CM2576 3A STEP DOWN VOLTAGE REGULATOR GENERAL DESCRIPTION FEATURES The CM2576 series are step-down switching regulators with ! Guaranteed 3A output current all required active functions. It is capable of driving 3A load ! 3.3V, 5V, and adjustable versions with excellent line and load regulations. These devices are ! Wide input voltage range, up to 40V available in fixed output voltages of 3.3V, 5V, and an ! Internal oscillator of 52KHz fixed frequency adjustable output version. ! Wide adjustable version output voltage range, from The CM2576 series offers a high-efficiency replacement for ! Low standby current, typ. 70µA, at shutdown mode popular three-terminal linear regulators. Also it requires a ! Requires only 4 external components minimum number of external components. It substantially not ! Thermal shutdown and current limit protection only reduces the area of board size but also the size of the ! P+ product enhancement tested 1.23V to 37V±4% max over line and load conditions heat sink, and in some cases no heat sink is required. ±4% tolerance on output voltage within specified input voltages and output load conditions is guaranteed. Also, the oscillator frequency accuracy is within ±10%. External shutdown is included, featuring 70µA (typical) standby current. The output switch includes cycle-by-cycle current limiting, as well as thermal shutdown for full protection under fault conditions. APPLICATIONS ! LCD Monitors ! ADD-ON Cards Switching Regulators ! High Efficiency Step-Down Regulators ! Efficient Pre-regulator for Linear Regulators ORDERING INFORMATION Package Type Temperature Range Output Voltage CM2576SCN263 -40℃ ~ +125℃ 3.3V CM2576ZJCN220 CM2576ZJCN263 -40℃ ~ +125℃ 5.0V CM2576CN220 CM2576CN263 -40℃ ~ +125℃ ADJ. TO-220 TO-263 CM2576SCN220 2003/08/07 Preliminary Rev. 1.1 Champion Microelectronic Corporation Page 1 CM2576 3A STEP DOWN VOLTAGE REGULATOR PIN CONFIGURATION TO-263 Top View FB EN ABLE 1 2 GND V OUT V IN TO-220 Top View 3 4 5 E N A B LE 5 FB GND 4 3 VOUT V IN 2 1 ABSOLUTE MAXIMUM RATINGS Input Voltage (VPOWER) …….………………………………………….……. +45V ENABLE Pin Input Voltage ….…………………………………. –0.3V ≦V≦VIN Operating Junction Temperature Range, TJ ……………...… 0℃ to +150℃ Storage Temperature ………………………………….….…... -65℃ to +150℃ Lead Temperature (10 sec.) ……..……………………..….…………….... 260℃ POWER DISSIPATION TABLE Package ℃/W) ΘJA (℃ TO-220 TO-263 45 45 Derating factor (mW/℃ ℃) ℃ TA >= 25℃ 22.2 22.2 TA <= 25℃ ℃ Power rating (mW) 2775 2775 TA = 70℃ ℃ TA = 85℃ ℃ Power rating (mW) Power rating (mW) 1776 1443 1776 1443 Note: 1. ΘJA : Thermal Resistance-Junction to Ambient, DF: Derating factor, PO: Power consumption. 2. Junction Temperature Calculation: TJ = TA + (PD x ΘJA ), PO = DF x (TJ – TA) The ΘJA numbers are guidelines for the thermal performance of the device/PC-board system. All of the above assume no ambient airflow. ΘJT : Thermal Resistance-Junction to Ambient, TC: case (Tab) temperature, TJ = TC + (PD x ΘJA ) RESOMMENDED OPERATING CONDITIONS Parameter Input Voltage (VIN) Temperature Range 2003/08/07 Preliminary Rev. 1.1 Symbol VIN TJ Min. -40 Champion Microelectronic Corporation Typ. Max 40 125 Units V ℃ Page 2 CM2576 3A STEP DOWN VOLTAGE REGULATOR ELECTRICAL CHARACTERISTICS Electrical Characteristics at IOUT = 0mA, and TJ = +25℃; unless otherwise noted Parameter Device Output Voltage CM2576S (Note 1) CM2576ZJ CM2576S 6V<=VIN <=40V (Note 1) CM2576ZJ 8V<=VIN <=40V CM2576S 6V<=VIN <=40V (Note 1) Feedback Voltage (Note 1) Feedback Voltage (Note 1) Feedback Voltage (Note 1) Test circuit of Figure 2 3.300 3.366 V 4.900 5.000 5.100 V 3.168 3.300 3.432 V 4.800 5.000 5.200 V 3.135 3.300 3.482 V 4.750 5.000 5.250 V VOUT =5V 1.217 1.230 1.243 V 0.5A<=ILOAD <=3A 1.193 1.230 1.267 V 1.180 1.230 1.286 V Test circuit of Figure 1 8V<=VIN <=40V, VOUT =5V Test circuit of Figure 2 8V<=VIN <=40V, VOUT =5V 0.5A<=ILOAD <=3A, Test circuit of Figure 2 -40℃<=TJ<=125℃ CM2576S Efficiency 3.234 0.5A<=ILOAD <=3A, CM2576 (Adj) CM2576 (Adj) Max. -40℃<=TJ<=125℃ 8V<=VIN <=40V CM2576 (Adj) Typ. 0.5A<=ILOAD <=3A CM2576ZJ 75 ILOAD =3A CM2576ZJ CM2576(adj) Note 2 % 77 ILOAD =3A, VOUT =5V Oscillator Frequency Unit Min. Test circuit of Figure 1 Output Voltage Output Voltage CM2576 Test Conditions 77 % TJ=25℃ 47 52 58 -40℃<=TJ<=125℃ 42 52 63 kHz Quiescent Current Note 3 5 10 mA Standby Current ENABLE = 5V 70 200 µA 1.4 1.8 Saturation Voltage Feedback Bias Current TJ=25℃ ILOAD =3A (Note 4) -40℃<=TJ<=125℃ VOUT =5V TJ=25℃ (Adj. Version only) -40℃<=TJ<=125℃ Duty Cycle (ON) Note 5 Current Limit Note 2,4 Output Leakage Current Note 3 VIH (VOUT =0V) ENABLE Threshold Voltage 100 500 98 TJ=25℃ 4.2 7 8.8 -40℃<=TJ<=125℃ 3.5 7.2 9.0 VOUT =0V 0.3 2 VOUT =-1V 9 20 TJ=25℃ 2.2 -40℃<=TJ<=125℃ 2.4 TJ=25℃ Voltage) -40℃<=TJ<=125℃ 2003/08/07 Preliminary Rev. 1.1 50 93 VIL (VOUT = Normal Output ENABLE Input Current 2.0 IIH ( ENABLE = 5V) IIH ( ENABLE = 0V) Champion Microelectronic Corporation nA % 1.4 1.2 V A mA V 1.0 0.8 12 30 0 10 Page 3 V µA CM2576 3A STEP DOWN VOLTAGE REGULATOR Note 1: External components such as the catch diode, inductor, input and output capacitors can affect switching regulator system performance. Refer to Application Information for details. Note 2: The oscillator frequency reduces to approximately 11KHz in the event of fault conditions, such as output short or overload. And the regulated output voltage will drop approximately 40% from the nominal output voltage. This self-protection feature lowers the average power dissipation by lowering the minimum duty cycle from 5% down to approximately 2%. Note 3: For these parameters, FB is removed from VOUT and connected to +12V to force the output transistor OFF. Note 4: VOUT pin sourcing current. No diode, inductor or capacitor connect to VOUT. Note 5: FB is removed from VOUT and connected to 0V. BLOCK DIAGRAM 2003/08/07 Preliminary Rev. 1.1 Champion Microelectronic Corporation Page 4 CM2576 3A STEP DOWN VOLTAGE REGULATOR APPLICATION CIRCUIT 2003/08/07 Preliminary Rev. 1.1 Champion Microelectronic Corporation Page 5 CM2576 3A STEP DOWN VOLTAGE REGULATOR TYPICAL CHARACTERISTICS 2003/08/07 Preliminary Rev. 1.1 Champion Microelectronic Corporation Page 6 CM2576 3A STEP DOWN VOLTAGE REGULATOR 2003/08/07 Preliminary Rev. 1.1 Champion Microelectronic Corporation Page 7 CM2576 3A STEP DOWN VOLTAGE REGULATOR APPLICATION INFORMATION It is required that VIN must be bypassed with at least a 100uF electrolytic capacitor for stability. Also, it is strongly recommended the capacitor’s leads must be dept short, and located near the regulator as possible. For low operating temperature range, for example, below -25℃, the input capacitor value may need to be larger. This is due to the reason that the capacitance value of electrolytic capacitors decreases and the ESR increases with lower temperatures and age. Paralleling a ceramic or solid tantalum capacitor will increase the regulator stability at cold temperatures. Output Capacitors (COUT) An output capacitor is also required to filter the output voltage and is needed for loop stability. The capacitor should be located near the CM2576 using short PC board traces. Low ESR types capacitors are recommended for low output ripple voltage and good stability. Generally, low value or low voltage (less than 12V) electrolytic capacitors usually have higher ESR numbers. For example, the lower capacitor values (220uF – 1000uF) will yield typically 50mV to 150mV of output ripple voltage, while larger-value capacitors will reduce the ripple to approximately 20mV to 50mV. The amount of output ripple voltage is primarily a function of the ESR (Equivalent Series Resistance) of the output capacitor and the amplitude of the inductor ripple current (△IIND). Output Ripple Voltage = (△IIND) x (ESR of COUT) Some capacitors called “high-frequency”, “low-inductance”, or “low-ESR” are recommended to use to further reduce the output ripple voltage to 10mV or 20mV. However, very low ESR capacitors, such as Tantalum capacitors, should be carefully evaluated. Catch Diode This diode is required to provide a return path for the inductor current when the switch is off. It should be located close to the CM2576 using short leads and short printed circuit traces as possible. To satisfy the need of fast switching speed and low forward voltage drop, Schottky diodes are widely used to provide the best efficiency, especially in low output voltage switching regulators (less than 5V). Besides, fast-Recovery, high-efficiency, or ultra-fast recovery diodes are also suitable. But some types with an abrupt turn-off characteristic may cause instability and EMI problems. A fast-recovery diode with soft recovery characteristics is better choice. 2003/08/07 Preliminary Rev. 1.1 Champion Microelectronic Corporation Page 8 CM2576 3A STEP DOWN VOLTAGE REGULATOR Output Voltage Ripple and Transients The output ripple voltage is due mainly to the inductor sawtooth ripple current multiplied by the ESR of the output capacitor. The output ripple voltage of a switching power supply will contain a sawtooth ripple voltages at the switcher frequency, typically about 1% of the output voltages, and may also contain short voltage spikes of the sawtooth waveform. Due to the fast switching action, and the parasitic inductance of the output filter capacitor, there is voltage spikes presenting at the peaks of the sawtooth waveform. Cautions must be taken for stray capacitance, wiring inductance, and even the scope probes used for transients evaluation. To minimize these voltage spikes, shortening the lead length and PCB traces is always the first thought. Further more, an additional small LC filter (30uH & 100uF) (as shown in Figure 3) will possibly provide a 10X reduction in output ripple voltage and transients. Inductor Selection The CM2576 can be used for either continuous or discontinuous modes of operation. Each mode has distinctively different operating characteristics, which can affect the regulator performance and requirements. With relatively heavy load currents, the circuit operates in the continuous mode (inductor current always flowing), but under light load conditions, the circuit will be forced to the discontinuous mode (inductor current falls to zero for a period of time). For light loads (less than approximately 300mA) it may be desirable to operate the regulator in the discontinuous mode, primarily because of the lower inductor values required for the discontinuous mode. Inductors are available in different styles such as pot core, toriod, E-frame, bobbin core, et., as well as different core materials, such as ferrites and powdered iron. The least expensive, the bobbin core type, consists of wire wrapped on a ferrite rod core. This type of construction makes for an inexpensive inductor, but since the magnetic flux is not completely contained within the core, it generates more electromagnetic interference (EMI). This EMI can cause problems in sensitive circuits, or can give incorrect scope readings because of induced voltages in the scope probe. 2003/08/07 Preliminary Rev. 1.1 Champion Microelectronic Corporation Page 9 CM2576 3A STEP DOWN VOLTAGE REGULATOR An inductor should not be operated beyond its maximum rated current because it may saturate. When an inductor begins to saturate, the inductance decreases rapidly and the inductor begins to look mainly resistive (the DC resistance of the winding). This will cause the switch current to rise very rapidly. Different inductor types have different saturation characteristics, and this should be well considered when selecting as inductor. Feedback Connection For fixed output voltage version, the FB (feedback) pin must be connected to VOUT. For the adjustable version, it is important to place the output voltage ratio resistors near CM2576 as possible in order to minimize the noise introduction. ENABLE It is required that the ENABLE must not be left open. For normal operation, connect this pin to a “LOW” voltage (typically, below 1.6V). On the other hand, for standby mode, connect this pin with a “HIGH” voltage. This pin can be safely pulled up to +VIN without a resistor in series with it. Grounding To maintain output voltage stability, the power ground connections must be low-impedance. For the 5-lead TO-220 and TO-263 style package, both the tab and pin 3 are ground and either connection may be used. Heatsink and Thermal Consideration Although the CM2576 requires only a small heatsink for most cases, the following thermal consideration is important for all operation. With the package thermal resistances θJA and θJC, total power dissipation can be estimated as follows: PD = (VIN x IQ) + (VOUT / VIN)(ILOAD x VSAT); When no heatsink is used, the junction temperature rise can be determined by the following: ∆TJ = PD x θJA; With the ambient temerpature, the actual junction temperature will be: TJ = ∆TJ + TA; If the actual operating junction temperature is out of the safe operating junction temperature (typically 125℃), then a heatsink is required. When using a heatsink, the junction temperature rise will be reduced by the following: ∆TJ = PD x (θJC + θinterface + θHeatsink); Also one can see from the above, it is important to choose an heatsink with adequate size and thermal resistance, such that to maintain the regulator’s junction temperature below the maximum operating temperature. 2003/08/07 Preliminary Rev. 1.1 Champion Microelectronic Corporation Page 10 CM2576 3A STEP DOWN VOLTAGE REGULATOR PACKAGE DIMENSION TO-220 (N220) C B S T F A B C A D F G J K 1 2 3 4 5 N R S K T G N R J D TO-263 (N263) C D L K B I A G F 2003/08/07 Preliminary Rev. 1.1 E Champion Microelectronic Corporation Page 11 CM2576 3A STEP DOWN VOLTAGE REGULATOR IMPORTANT NOTICE Champion Microelectronic Corporation (CMC) reserves the right to make changes to its products or to discontinue any integrated circuit product or service without notice, and advises its customers to obtain the latest version of relevant information to verify, before placing orders, that the information being relied on is current. A few applications using integrated circuit products may involve potential risks of death, personal injury, or severe property or environmental damage. CMC integrated circuit products are not designed, intended, authorized, or warranted to be suitable for use in life-support applications, devices or systems or other critical applications. understood to be fully at the risk of the customer. Use of CMC products in such applications is In order to minimize risks associated with the customer’s applications, the customer should provide adequate design and operating safeguards. HsinChu Headquarter Sales & Marketing 5F, No. 11, Park Avenue II, Science-Based Industrial Park, HsinChu City, Taiwan T E L : +886-3-567 9979 F A X : +886-3-567 9909 11F, No. 306-3, SEC. 1, Ta Tung Road, Hsichih, Taipei Hsien 221, Taiwan 2003/08/07 Preliminary Rev. 1.1 T E L : +886-2-8692 1591 F A X : +886-2-8692 1596 Champion Microelectronic Corporation Page 12