CXP847P60 CMOS 8-bit Single Chip Microcomputer Description The CXP847P60 is a CMOS 8-bit single chip microcomputer integrating on a single chip an A/D converter, serial interface, timer/counter, time base timer, capture timer/counter, FRC capture unit, highprecision timing pattern generation circuit, PWM output, and the like besides the basic configurations of 8-bit CPU, PROM, RAM, and I/O ports. The CXP847P60 also provides the sleep/stop functions that enable to execute the power-on reset function and lower the power consumption. The CXP847P60 is the PROM-incorporated version of the CXP84716/84720/84724 with built-in mask ROM. This provides the additional feature of being able to write directly into the program. Thus, it is most suitable for evaluaiton use during system development and for small-quantity production. 100 pin QFP (Plastic) 100 pin LQFP (Plastic) Structure Silicon gate CMOS IC Features • A wide instruction set (213 instructions) which covers various types of data. — 16-bit arithmetic/multiplication and division/Boolean bit operation instructions • Minimum instruction cycle 250ns at 16MHz operation (4.5 to 5.5V) 333ns at 12MHz operation (3.0 to 5.5V) • Incorporated PROM capacity 60K bytes • Incorporated RAM capacity 2144 bytes • Peripheral functions — A/D converter 8 bits, 8 channels, successive approximation method (Conversion time of 1.6µs at 16MHz) — Serial interface Srart-stop synchronization (UART), 1 channel Incorporated buffer RAM (Auto transfer for 1 to 32 bytes), 2 channels 8-bit clock syncronization (MSB/LSB first selectable), 1 channel — Timer 8-bit timer, 8-bit timer/counter, 19-bit time base timer, 16-bit capture timer/counter — FRC capture unit Incorporated 24-bit and 6-stage FIFO — High-precision timing pattern generation circuit PPG: maximum of 11 pins, 16 stages programmable, 2 channels — PWM output 8 bits, 8 channels • Interruption 19 factors, 15 vectors, multi-interruption possible • Standby mode Sleep/stop • Package 100-pin plastic QFP/LQFP Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits. –1– E97119-PS AVREF AVSS 8 BIT PWM GENERATOR 4 8 BIT PWM GENERATOR 5 8 BIT PWM GENERATOR 6 PWM4 PWM5 PWM6 TO CINT EC1 16 BIT CAPTURE TIMER/COUNTER 2 8 BIT TIMER 1 8 BIT TIMER/COUNTER 0 EC0 BUFFER RAM SERIAL INTERFACE UNIT (CH2) SERIAL INTERFACE UNIT (CH1) CS1 SI1 SO1 SCK1 BUFFER RAM SI2 SO2 SCK2 SERIAL INTERFACE UNIT (CH0) CS0 SI0 SO0 SCK0 8 BIT PWM GENERATOR 7 8 BIT PWM GENERATOR 2 8 BIT PWM GENERATOR 3 PWM7 8 BIT PWM GENERATOR 1 PWM2 PWM3 8 BIT PWM GENERATOR 0 UART BAUD RATE GENERATOR UART RECEIVER UART TRANSMITTER PWM0 PWM1 TxD AVDD A/D CONVERTER 2 2 NMI FIFO 4 11 PROGRAMMABLE PATTERN BUFFER GENERATOR RAM (CH1) FRC CAPTURE UNIT RAM 2144 BYTES CLOCK GENERATOR/ SYSTEM CONTROL 11 PROGRAMMABLE PATTERN BUFFER GENERATOR RAM (CH0) PRESCALER/ TIME BASE TIMER PROM 60K BYTES SPC 700 CPU CORE PPO0 to PPO10 RxD 8 INTERRUPT CONTROLLER NMI INT0 INT1 INT2 INT3 INT4 PPO11 to PPO21 AN0 to AN7 EXTAL XTAL RST VDD VSS EXI0 to EXI3 –2– PORT I PORT H PORT G PORT F PORT E PORT D PORT C PORT B PORT A PORT J Block Diagram PI0 to PI7 8 PJ0 to PJ7 PH0 to PH7 8 8 PG0 to PG7 PF6 PF7 PF0 to PF5 PE6 to PE7 PE0 to PE5 PD0 to PD7 PC0 to PC7 PB0 to PB7 PA0 to PA7 8 6 2 6 8 8 8 8 CXP847P60 CXP847P60 PI2/INT2 PI3/INT3 PI4/INT4 PI5/SCK2 PI6/SI2 PI7/SO2 PG0/PWM0 VDD VSS Vpp PG1/PWM1 PG2/PWM2 PG3/PWM3 PG4/PWM4 PG5/PWM5 PG6/PWM6 PG7/PWM7 PF0 PF1 PF2 Pin Assignment (Top View) 100-pin QFP package 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 PF3 1 80 PI1/INT1 PF4 2 79 PI0/INT0 PF5 3 78 PE7/TO PF6/TxD 4 77 PE6 PF7/RxD 5 76 PE5 PD0/PPO0 6 75 PE4 PD1/PPO1 7 74 PE3/NMI PD2/PPO2 8 73 PE2 PD3/PPO3 9 72 PE1/EC1 PD4/PPO4 10 71 PE0/EC0 11 70 PB7/SO1 PD5/PPO5 PD6/PPO6 12 69 PB6/SI1 PD7/PPO7 13 68 PB5/SCK1 PC0 14 67 PB4/CS1 PC1 15 66 PB3 PC2 16 65 PB2 PC3 17 64 PB1 PC4 18 63 PB0/CINT PC5 19 62 SO0 PC6 20 61 SI0 PC7 21 60 SCK0 PH0/PPO8 22 59 CS0 PH1/PPO9 23 58 PA7 PH2/PPO10 24 57 PA6 PH3/PPO11 25 56 PA5 PH4/PPO12 26 55 PA4 PH5/PPO13 27 54 PA3/AN7 PH6/PPO14 28 53 PA2/AN6 PH7/PPO15 29 52 PA1/AN5 PJ0/PPO16 30 51 PA0/AN4 Note) 1. Vpp (Pin 90) is left open. 2. VSS (Pins 41 and 88) are both connected to GND. –3– AN3 AN2 AN1 AN0 AVDD AVREF AVSS EXI3 EXI2 VSS XTAL EXTAL RST PJ7/EXI1 PJ6/EXI0 PJ5/PPO21 PJ4/PPO20 PJ3/PPO19 PJ2/PPO18 PJ1/PPO17 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 CXP847P60 PE7/TO PI0/INT0 PI1/INT1 PI2/INT2 PI3/INT3 PI4/INT4 PI5/SCK2 PI6/SI2 PI7/SO2 PG0/PWM0 VDD VSS Vpp PG1/PWM1 PG2/PWM2 PG3/PWM3 PG4/PWM4 PG5/PWM5 PG6/PWM6 PG7/PWM7 PF0 PF1 PF2 PF3 PF4 Pin Assignment (Top View) 100-pin LQFP package 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 PF5 1 75 PE6 PF6/TxD 2 74 PE5 PF7/RxD 3 73 PE4 PD0/PPO0 4 72 PE3/NMI PD1/PPO1 5 71 PE2 PD2/PPO2 6 70 PE1/EC1 PD3/PPO3 7 69 PE0/EC0 PD4/PPO4 8 68 PB7/SO1 PD5/PPO5 9 67 PB6/SI1 PD6/PPO6 10 66 PB5/SCK1 PD7/PPO7 11 65 PB4/CS1 PC0 12 64 PB3 PC1 13 63 PB2 PC2 14 62 PB1 PC3 15 61 PB0/CINT PC4 16 60 SO0 PC5 17 59 SI0 PC6 18 58 SCK0 PC7 19 57 CS0 PH0/PPO8 20 56 PA7 PH1/PPO9 21 55 PA6 PH2/PPO10 22 54 PA5 PH3/PPO11 23 53 PA4 PH4/PPO12 24 52 PA3/AN7 PH5/PPO13 25 51 PA2/AN6 Note) 1. Vpp (Pin 88) is left open. 2. VSS (Pins 39 and 86) are both connected to GND. –4– PA1/AN5 AN3 PA0/AN4 AN2 AN1 AN0 AVDD AVSS AVREF EXI3 EXI2 VSS XTAL EXTAL RST PJ7/EXI1 PJ6/EXI0 PJ5/PPO21 PJ4/PPO20 PJ3/PPO19 PJ2/PPO18 PJ1/PPO17 PJ0/PPO16 PH7/PPO15 PH6/PPO14 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 CXP847P60 Pin Description Symbol AN0 to AN3 I/O Input PA0/AN4 to PA3/AN7 I/O/Input PA4 to PA7 I/O PB0/CINT I/O/Input PB1 to PB3 I/O PB4/CS1 I/O/Input PB5/SCK1 I/O/I/O PB6/SI1 I/O/Input PB7/SO1 I/O/Output Description Analog inputs to A/D converter. (4 pins) (Port A) 8-bit I/O port. I/O can be set in a unit of single bits. Incorporation of pull-up resistor can be set through the software in a unit of 4 bits. (8 pins) Analog inputs to A/D converter. (4 pins) External capture input to 16-bit timer/counter. (Port B) 8-bit I/O port. I/O can be set in a unit of single bits. Incorporation of pull-up resistor can be set through the software in a unit of 4 bits. (8 pins) Chip select input for serial interface (CH1). Serial clock I/O (CH1). Serial data input (CH1). Serial data output (CH1). I/O (Port C) 8-bit I/O port. I/O can be set in a unit of single bits. Can drive 12mA sink current. Incorporation of pull-up resistor can be set through the software in a unit of 4 bits. (8 pins) PD0/PPO0 to PD7/PPO7 I/O/Real-time output (Port D) 8-bit I/O port. I/O can be set in a unit of single bits. Incorporation of pull-up resistor can be set through the software in a unit of 4 bits. Data is gated with PPO contents by OR-gate and they are output. (8 pins) PE0/EC0 Input/Input PE1/EC1 Input/Input PE2 Input PE3/NMI Input/Input PE4 to PE5 Input PE6 Output PE7/TO Output/Output PC0 to PC7 PPO0 to PPO7 outputs for programmable pattern generator (PPG0). Functions as high-precision real-time pulse output port. (PPG0: 11 pins; PPG1: 11 pins) External event inputs for timer/counter. (2 pins) (Port E) 8-bit port. Lower 6 bits are for input; upper 2 bits are for output. (8 pins) Non-maskable interruption request. Rectangular wave output for 16-bit timer/counter. –5– CXP847P60 Symbol I/O Description (Port F) Lower 6 bits are for I/O. I/O can be set in a unit of single bits. Incorporation of pull-up resistor can be set through the software in a unit of 4 bits (PF0 to PF3) or 2 bits (PF4, PF5). PF6 is for output; PF7 is for input. (8 pins) PF0 to PF5 I/O PF6/TXD Output/Output UART transmission data output. PF7/RXD Input/Input UART reception data input. I/O/Output (Port G) 8-bit I/O port. I/O can be set in a unit of single bits. Incorporation of pull-up resistor can be set through the software in a unit of 4 bits. (8 pins) PWM outputs. (8 pins) PH0/PPO8 to PH7/PPO15 I/O/Real-time output (Port H) 8-bit I/O port. I/O can be set in a unit of single bits. Incorporation of pull-up resistor can be set through the software in a unit of 4 bits. Data is gated with PPO contents by OR-gate and they are output. (8 pins) PPO8 to PPO11 (PPG0) outputs and PPO12 to PPO15 (PPG1) outputs for programmable pattern generator (PPG0, PPG1). Functions as high-precision real-time pulse output port. PI0/INT0 to PI4/INT4 I/O/Input PI5/SCK2 I/O/I/O PI6/SI2 I/O/Input PI7/SO2 I/O/Output PG0/PWM0 to PG7/PWM7 PJ0/PPO16 to PJ5/PPO21 I/O/Real-time output PJ6/EXI0 I/O/Input PJ7/EXI1 I/O/Input EXI2 to EXI3 Input (Port I) 8-bit I/O port. I/O can be set in a unit of single bits. Incorporation of pull-up resistor can be set through the software in a unit of 4 bits. (8 pins) (Port J) 8-bit I/O port. I/O can be set in a unit of single bits. Incorporation of pull-up resistor can be set through the software in a unit of 4 bits. Data is gated with PPO contents by OR-gate and they are output. (8 pins) External interruption request inputs. (5 pins) Serial clock I/O (CH2). Serial data input (CH2). Serial data output (CH2). PPO16 to PPO21 outputs for programmable pattern generator (PPG1). Functions as high-precision real-time pulse output port. External inputs to FRC capture unit. (2 pins) External inputs to FRC capture unit. (2 pins) CS0 Input Chip select input for serial interface (CH0). SCK0 I/O Serial clock I/O (CH0). SI0 Input Serial data input (CH0). SO1 Output Serial data output (CH0). –6– CXP847P60 Symbol I/O EXTAL Input XTAL Output RST I/O Description Connects a crystal for system clock oscillation. When a clock is supplied externally, input it to EXTAL pin and input a reversed phase clock to XTAL pin. System reset; active at Low level. This pin is I/O pin, and outputs Low level at the power on with the power-on reset function executed. (Mask option) Vpp Positive power supply for incorporated PROM writing. Leave this pin open for normal operation. (Internally connected to VDD.) AVDD Positive power supply of A/D converter. AVREF Input Reference voltage input of A/D converter. AVSS GND of A/D converter. VDD Positive power supply. VSS GND. –7– CXP847P60 I/O Circuit Format for Pins Pin Port A AAA AAA AAA AAA AAA AAA AAA ∗ Pull-up resistor AA AA AA AA "0" when reset Port A data PA0/AN4 to PA3/AN7 When reset Circuit format Port A direction Input protection circuit IP "0" when reset Data bus Hi-Z RD (Port A) Port A function selection Input multiplexer "0" when reset 4 pins Port A Port B Port F A/D converter AAAA AAAA AAAAA AAAAA AAAAA Pull-up resistor "0" when reset Ports A, B, F data PA4 to PA7 PB1 to PB3 PF0 to PF5 Ports A, B, F direction "0" when reset Data bus RD (Ports A, B, F) 13 pins Port B Port I AAAA AAAA AAAA AAAA AAAA Pull-up resistor "0" when reset Port J PB0/CINT PB4/CS1 PB6/SI1 PI6/SI2 PJ6/EXI0 PJ7/EXI1 Ports B, I, J data Ports B, I, J direction "0" when reset Data bus ∗ Pull-up transistors approx. 100kΩ (VDD = 4.5 to 5.5V) approx. 300kΩ (VDD = 3.0 to 3.6V) ∗ AA AA AA AA IP ∗ Pull-up transistors approx. 100kΩ (VDD = 4.5 to 5.5V) approx. 300kΩ (VDD = 3.0 to 3.6V) ∗ AA AA AA AA IP Schmitt input RD (Ports B, I, J) 6 pins CINT CS1 SI1 SI2 EXI0 EXI1 –8– Hi-Z ∗ Pull-up transistors approx. 100kΩ (VDD = 4.5 to 5.5V) approx. 300kΩ (VDD = 3.0 to 3.6V) Hi-Z CXP847P60 AAAA AAAA AAAA AAAA AAAA AAAA Pin When reset Circuit format Port B ∗ Pull-up resistor Port I "0" when reset SCK OUT Serial clock output enable AA AAAA Ports B, I function selection "0" when reset PB5/SCK1 PI5/SCK2 IP Ports B, I data Ports B, I direction Hi-Z "0" when reset Data bus Schmitt input RD (Ports B, I) SCK in 2 pins Port B AAAA AAAA AAAA AAAA AAAA ∗ Pull-up transistors approx. 100kΩ (VDD = 4.5 to 5.5V) approx. 300kΩ (VDD = 3.0 to 3.6V) ∗ Pull-up resistor Port I "0" when reset SO Serial data output enable AA AAAA Ports B, I function selection "0" when reset PB7/SO1 PI7/SO2 IP Ports B, I data Ports B, I direction Hi-Z "0" when reset Data bus RD (Ports B, I) 2 pins Port C ∗ Pull-up transistors approx. 100kΩ (VDD = 4.5 to 5.5V) approx. 300kΩ (VDD = 3.0 to 3.6V) AAA AAA AAA AAA AAA ∗2 Pull-up resistor AA AA AA AA "0" when reset Port C data PC0 to PC7 ∗1 Port C direction "0" when reset Data bus RD (Port C) IP ∗1 Large current 12mA ∗2 Pull-up transistors approx. 100kΩ (VDD = 4.5 to 5.5V) approx. 300kΩ (VDD = 3.0 to 3.6V) 8 pins –9– Hi-Z CXP847P60 Pin Port D PD0/PPO0 to PD7/PPO7 Port H Port J AAAA AAAA AAAA AAAA AAAA ∗ Pull-up resistor "0" when reset PPO data AAA Ports D, H, J data PH0/PPO8 to PH7/PPO15 Ports D, H, J direction PJ0/PPO16 to PJ5/PPO21 "0" when reset 22 pins ∗ Pull-up transistors approx. 100kΩ (VDD = 4.5 to 5.5V) approx. 300kΩ (VDD = 3.0 to 3.6V) Port E A A Port F Schmitt input (Inverter input for PE2, PE4, PE5) IP EC0, EC1, NMI, RxD Hi-Z Data bus RD (Ports E, F) 7 pins AAAA AAAA AA AA Port E PE6 Hi-Z IP Data bus RD (Ports D, H, J) PE0/EC0 PE1/EC1 PE2 PE3/NMI PE4 PE5 PF7/RxD When reset Circuit format Port E data "1" when reset Data bus 1 pin High level RD (Port E) Port E AAAA AAAA AAAAA AAAAA Internal reset signal 00 Port E data PE7/TO "1" when reset TO MPX AA ( AA ∗ 01 Port E function selection (upper) Port E function selection (lower) ∗ Pull-up transistors "00" when reset TO output enable 1 pin – 10 – approx. 150kΩ (VDD = 4.5 to 5.5V) approx. 400kΩ (VDD = 3.0 to 3.6V) High level with the resistor of pullup transistor ON for reset ) CXP847P60 Pin AAAAA AAAAA AAAA AAAA When reset Circuit format Port F UART transmission circuit Control for transmission and ports PF6/TxD A "0" when reset Port F data "1" when reset High level Data bus 1 pin RD (Port F) Port G AAAA AAAA AAAA AAAA AAAA ∗ Pull-up resistor "0" when reset PWM AA AAAA Port G function selection PG0/PWM0 to PG7/PWM7 "0" when reset IP Port G data Port G direction Hi-Z "0" when reset Data bus RD (Port G) 8 pins Port I AAAA AAAA AAAA AAAA AAAA Pull-up resistor "0" when reset Port I data PI0/INT0 to PI4/INT4 Port I direction "0" when reset Data bus RD (Port I) 5 pins AN0 to AN3 4 pins INT0 INT1 INT2 INT3 INT4 AA AA AAAA ∗ Pull-up transistors approx. 100kΩ (VDD = 4.5 to 5.5V) approx. 300kΩ (VDD = 3.0 to 3.6V) ∗ AA AA AA AA IP Hi-Z Schmitt input ∗ Pull-up transistors approx. 100kΩ (VDD = 4.5 to 5.5V) approx. 300kΩ (VDD = 3.0 to 3.6V) Input multiplexer IP – 11 – A/D converter Hi-Z CXP847P60 Pin When reset Circuit format AA A AA AAAA AA EXI2 EXI3 Schmitt input EXI2, EXI3 IP 2 pins CS0 SI0 Schmitt input 2 pins AA AA SO0 SO0 from SIO SO0 output enable AA AA AA AA Internal serial clock from SIO SCK0 External serial clock to SIO 1 pin 2 pins Hi-Z High level IP SCK0 output enable EXTAL XTAL Hi-Z SIO IP 1 pin Hi-Z Schmitt input AA AA A AA AA AA EXTAL IP IP • Diagram shows the circuit composition during oscillation. • Feedback resistor is removed during stop mode and XTAL becomes High level. Oscillation XTAL Pull-up resistor RST OP Mask option IP 1 pin Schmitt input From power-on reset circuit (Mask option) See the Selection Guide for the Mask option. – 12 – Low level (During a reset) CXP847P60 Absolute Maximum Ratings Item (Vss = 0V reference) Rating Unit VDD –0.3 to +7.0 V Vpp V AVDD –0.3 to +13.0 AVSS to +7.0∗1 AVSS –0.3 to +0.3 V AVREF V VIN AVSS to +7.0 –0.3 to +7.0∗2 Output voltage VOUT –0.3 to +7.0∗2 V High level output current IOH –5 mA Output (value per pin) –50 mA Total for all output pins IOL 15 mA All pins excluding large current outputs (value per pin) IOLC 20 mA Large current outputs (value per pin) ∗3 Low level total output current ∑IOL 100 mA Total for all output pins Operating temperature Topr –10 to +75 °C Storage temperature Tstg –55 to +150 °C Allowable power dissipation PD Supply voltage Input voltagte Symbol High level total output current ∑IOH Low level output current 600 380 Remarks Incorporated PROM V V mW QFP package LQFP package ∗1 AVDD and VDD must be set to the same voltage. ∗2 VIN and VOUT must not exceed VDD + 0.3V. ∗3 The large current output pins are Port C (PC). Note) Usage exceeding absolute maximum ratings may permanently impair the LSI. Normal operation should be conducted under the recommended operating conditions. Exceeding these conditions may adversely affect the reliability of the LSI. – 13 – CXP847P60 Recommended Operating Conditions Item Supply voltage Analog voltage Symbol VDD AVDD VIH High level input voltage VIHS VIHEX VIL Low level input voltage VILS VILEX Operating temperature Topr (Vss = 0V reference) Min. Max. Unit Remarks 4.5 5.5 V 3.0 5.5 V fc = 16MHz or less Guaranteed operation range for 1/2 and 1/4 fc = 12MHz or less frequency dividing clock. 2.7 5.5 V 2.5 5.5 V 3.0 5.5 V Guaranteed data hold range during stop mode ∗1 0.7VDD VDD V ∗2, ∗5 0.8VDD VDD V ∗2, ∗6 0.8VDD VDD V VDD – 0.4 VDD + 0.3 V VDD – 0.2 VDD + 0.2 V Guaranteed operation range for 1/16 frequency dividing clock or sleep mode Hysteresis input∗3 EXTAL pin∗4, ∗5 0 0.3VDD V EXTAL pin∗4, ∗6 ∗2, ∗5 0 0.2VDD V ∗2, ∗6 0 0.2VDD V –0.3 0.4 V Hysteresis input∗3 EXTAL pin∗4, ∗5 –0.3 0.2 V EXTAL pin∗4, ∗6 –10 +75 °C ∗1 AVDD and VDD must be set to the same voltage. ∗2 Normal input port (PA, PB1 to PB3, PB7, PC, PD, PE2, PE4, PE5, PF0 to PF5, PG, PH, PI7, PJ0 to PJ5) ∗3 RST, CINT, CS0, CS1, SCK0, SCK1, SCK2, SI0, SI1, SI2, EC0, EC1, NMI, RxD, INT0, INT1, INT2, INT3, INT4, EXI0, EXI1, EXI2 and EXI3 ∗4 Specifies only when the external clock is input. ∗5 This case applies to the range of 4.5 to 5.5V supply voltage (VDD). ∗6 This case applies to the range of 3.0 to 5.5V supply voltage (VDD). – 14 – CXP847P60 Electrical Characteristics (Ta = –10 to +75°C, VSS = 0V reference) DC Characteristics (VDD = 4.5 to 5.5V) Item Symbol High level VOH output voltage Low level VOL output voltage Pins PA to PD, VDD = 4.5V, IOH = –0.5mA PE6, PE7, PF0 to PF6, PG to PJ, VDD = 4.5V, IOH = –1.2mA SCK0, SO0 IILE IIHT Input current IILT IILR IIL I/O leakage current IIZ Min. EXTAL TEX Typ. Max. Unit 4.0 V 3.5 V PA to PD, VDD = 4.5V, IOL = 1.8mA PE6, PE7, PF0 to PF6, PG to PJ, SCK0, SO0, VDD = 4.5V, IOL = 3.6mA RST∗1 PC IIHE Conditions VDD = 4.5V, IOL = 12.0mA 0.4 V 0.6 V 1.5 V VDD = 5.5V, VIH = 5.5V 0.5 40 µA VDD = 5.5V, VIL = 0.4V –0.5 –40 µA VDD = 5.5V, VIL = 5.5V 0.1 10 µA VDD = 5.5V, VIL = 0.4V –0.1 –10 µA –1.5 –400 µA –45 µA RST∗2 VDD = 5.5V, VIL = 0.4V PA to PD∗3, PF0 to PF5∗3, VDD = 4.5V, VIL = 4.0V PG to PJ∗3 ∗ 3 PA to PD , PE0 to PE5, PF0 to PF5∗3, PF7, PG to PJ∗3, VDD = 5.5V CS0, SCK0, VI = 0, 5.5V SI0, EXI2, EXI3, AN0 to AN3 RST∗2 – 15 – –2.78 µA ±10 µA CXP847P60 Item Symbol Pins Conditions Min. Typ. Max. Unit 24 50 mA 1.5 10 mA 10 µA 20 pF 1/2 frequency dividing clock operation IDD Supply current∗4 Sleep mode IDDS1 IDDS2 Input capacity VDD = 5.5V, 16MHz crystal oscillation (C1 = C2 = 15pF) CIN VDD VDD = 5.5V, 16MHz crystal oscillation (C1 = C2 = 15pF) Stop mode VDD = 5.5V, termination of 16MHz crystal oscillation PA to PD, PE0 to PE5, PF0 to PF5, PF7, PG to PJ, Clock 1MHz CS0, SCK0, 0V for all pins excluding measured SI0, EXI2, pins EXI3, AN0 to AN3, EXTAL, RST 10 ∗1 RST pin specifies the output voltage only when the power-on reset circuit is selected with mask option. ∗2 RST pin specifies the input current when the pull-up resistance is selected, and specifies the leakage current when no resistance is selected. ∗3 PA to PD, PF0 to PF5 and PG to PJ pins specify the input current when the pull-up resistance is selected, and specify the leakage current when no resistance is selected. ∗4 When all pins are open. Note) See the Selection Guide for the mask option. – 16 – CXP847P60 Electrical Characteristics (Ta = –10 to +75°C, VSS = 0V reference) DC Characteristics (VDD = 3.0 to 3.6V) Item Symbol High level VOH output voltage Low level VOL output voltage Pins PA to PD, VDD = 3.0V, IOH = –0.15mA PE6, PE7, PF0 to PF6, PG to PJ, VDD = 3.0V, IOH = –0.5mA SCK0, SO0 IILE IIHT Input current IILT IILR IIL I/O leakage current IIZ Min. EXTAL TEX Typ. Max. Unit 2.7 V 2.3 V PA to PD, VDD = 3.0V, IOL = 1.2mA PE6, PE7, PF0 to PF6, PG to PJ, SCK0, SO0, VDD = 3.0V, IOL = 1.6mA RST∗1 PC IIHE Conditions VDD = 3.0V, IOL = 5.0mA 0.3 V 0.5 V 1 V VDD = 3.6V, VIH = 3.6V 0.3 20 µA VDD = 3.6V, VIL = 0.3V –0.3 –20 µA VDD = 3.6V, VIL = 3.6V 0.1 10 µA VDD = 3.6V, VIL = 0.4V –0.1 –10 µA –0.9 –200 µA –20 µA RST∗2 VDD = 3.6V, VIL = 0.3V PA to PD∗3, PF0 to PF5∗3, VDD = 3.0V, VIL = 2.7V PG to PJ∗3 ∗ 3 PA to PD , PE0 to PE5, PF0 to PF5∗3, PF7, PG to PJ∗3, VDD = 3.6V CS0, SCK0, VI = 0, 3.6V SI0, EXI2, EXI3, AN0 to AN3 RST∗2 – 17 – –1.0 µA ±10 µA CXP847P60 Item Symbol Pins Conditions Min. Typ. Max. Unit 10 25 mA 0.5 2.0 mA 10 µA 20 pF 1/2 frequency dividing clock operation IDD Supply current∗4 Sleep mode IDDS1 IDDS2 Input capacity VDD = 3.6V, 12MHz crystal oscillation (C1 = C2 = 15pF) CIN VDD VDD = 3.6V, 12MHz crystal oscillation (C1 = C2 = 15pF) Stop mode VDD = 3.6V, termination of 12MHz crystal oscillation PA to PD, PE0 to PE5, PF0 to PF5, PF7, PG to PJ, Clock 1MHz CS0, SCK0, 0V for all pins excluding measured SI0, EXI2, pins EXI3, AN0 to AN3, EXTAL, RST 10 ∗1 RST pin specifies the output voltage only when the power-on reset circuit is selected with mask option. ∗2 RST pin specifies the input current when the pull-up resistance is selected, and specifies the leakage current when no resistance is selected. ∗3 PA to PD, PF0 to PF5 and PG to PJ pins specify the input current when the pull-up resistance is selected, and specify the leakage current when no resistance is selected. ∗4 When all pins are open. Note) See the Selection Guide for the mask option. – 18 – CXP847P60 AC Characteristics (1) Clock timing Item (Ta = –10 to +75°C, VDD = 3.0 to 5.5V, Vss = 0V reference) Symbol Pin Conditions Min. VDD = 4.5 to 5.5V fC XTAL EXTAL Fig. 1, Fig. 2 System clock input pulse width tXL tXH XTAL EXTAL Fig. 1, Fig. 2 VDD = 4.5 to 5.5V External clock drive System clock input rise time, fall time tCR tCF tEH tEL tER tEF XTAL EXTAL Fig. 1, Fig. 2 External clock drive EC0 EC1 Fig. 3 EC0 EC1 Fig. 3 System clock frequency Event count input clock pulse width Event count input clock rise time, fall time Typ. Max. 1 16 1 12 28 Unit MHz ns 37.5 200 tsys + 50∗1 ns ns 20 ms ∗1 tsys indicates the three values below according to the upper two bits (CPU clock selection) of the clock control register (CLC: 00FEH). tsys [ns] = 2000/fc (upper two bits = “00”), 4000/fc (upper two bits = “01”), 16000/fc (Upper two bits = “11”) Fig. 1. Clock timing 1/fc VDD – 0.4V (VDD = 4.5 to 5.5V) VDD – 0.3V EXTAL 0.4V (VDD = 4.5 to 5.5V) 0.3V tCF tXH tXL tCR AAAA AAAA AAAA AAAA AAAA AAAA Fig. 2. Clock applied conditions Crystal oscillation Ceramic oscillation EXTAL XTAL C1 External clock EXTAL C2 XTAL 74HC04 Fig. 3. Event count clock timing 0.8VDD EC0 EC1 0.2VDD tEH tEF – 19 – tEL tER CXP847P60 (Ta = –10 to +75°C, VDD = 4.5 to 5.5V, Vss = 0V reference) (2) Serial transfer (CH0, CH1) Item Symbol Pin Conditions Min. Max. Unit CS↓ → SCK delay time tDCSK SCK0 SCK1 Chip select transfer mode (SCK = output mode) 1.5tsys + 200 ns CS↑ → SCK floating delay time tDCSKF SCK0 SCK1 Chip select transfer mode (SCK = output mode) 1.5tsys + 200 ns CS↓ → SO delay time tDCSO SO0 SO1 Chip select transfer mode 1.5tsys + 200 ns CS↑ → SO floating delay time tDCSOF SO0 SO1 Chip select transfer mode 1.5tsys + 200 ns CS High level width tWHCS CS0 CS1 Chip select transfer mode tsys + 200 ns SCK cycle time tKCY SCK0 SCK1 Input mode 2tsys + 200 ns 8000/fc ns SCK High and Low level widths tKH tKL SCK0 SCK1 Input mode tsys + 100 ns Output mode 4000/fc – 50 ns SI input setup time (for SCK↑) tSIK SI0 SI1 SCK input mode –tsys + 100 ns 200 ns SI input hold time (for SCK↑) tKSI SI0 SI1 SCK input mode 2tsys + 200 ns 100 ns SCK↓ → SO delay time tKSO SO0 SO1 SCK input mode Output mode SCK output mode SCK output mode SCK output mode 2tsys + 200 ns 100 ns Note 1) tsys indicates three values according to the contents of the clock control register (CLC: 00FEH) upper 2 bits (CPU clock selection). tsys [ns] = 2000/fc (upper 2 bits = “00”), 4000/fc (upper 2 bits = “01”), 16000/fc (upper 2 bits = “11”) Note 2) CS, SCK, SI and SO represent CS0, SCK0, SI0 and SO0 for CH0; they represent CS1, SCK1, SI1 and SO1 for CH1, respectively. Note 3) The load of SCK output mode and SO output delay time is 50pF + 1TTL. – 20 – CXP847P60 Serial transfer (CH0, CH1) Item Symbol (Ta = –10 to +75°C, VDD = 3.0 to 3.6V, Vss = 0V reference) Pin Conditions Min. Max. Unit CS↓ → SCK delay time tDCSK SCK0 SCK1 Chip select transfer mode (SCK = output mode) 1.5tsys + 250 ns CS↑ → SCK floating delay time tDCSKF SCK0 SCK1 Chip select transfer mode (SCK = output mode) 1.5tsys + 200 ns CS↓ → SO delay time tDCSO SO0 SO1 Chip select transfer mode 1.5tsys + 250 ns CS↑ → SO floating delay time tDCSOF SO0 SO1 Chip select transfer mode 1.5tsys + 200 ns CS High level width tWHCS CS0 CS1 Chip select transfer mode tsys + 200 ns SCK cycle time tKCY SCK0 SCK1 Input mode 2tsys + 200 ns 8000/fc ns SCK High and Low level widths tKH tKL SCK0 SCK1 Input mode tsys + 100 ns 4000/fc – 100 ns SI input setup time (for SCK↑) tSIK SI0 SI1 SCK input mode –tsys + 100 ns 200 ns SI input hold time (for SCK↑) tKSI SI0 SI1 SCK input mode 2tsys + 200 ns 100 ns SCK↓ → SO delay time tKSO SO0 SO1 SCK input mode Output mode Output mode SCK output mode SCK output mode SCK output mode 2tsys + 250 ns 125 ns Note 1) tsys indicates three values according to the contents of the clock control register (CLC: 00FEH) upper 2 bits (CPU clock selection). tsys [ns] = 2000/fc (upper 2 bits = “00”), 4000/fc (upper 2 bits = “01”), 16000/fc (upper 2 bits = “11”) Note 2) CS, SCK, SI and SO represent CS0, SCK0, SI0 and SO0 for CH0; they represent CS1, SCK1, SI1 and SO1 for CH1, respectively. Note 3) The load of SCK output mode and SO output delay time is 50pF. – 21 – CXP847P60 Fig. 4. Serial transfer CH0, CH1 timing tWHCS CS0 CS1 0.8VDD 0.2VDD tKCY tDCSK tKL tDCSKF tKH 0.8VDD 0.8VDD SCK0 SCK1 0.2VDD tSIK tKSI 0.8VDD SI0 SI1 Input data 0.2VDD tDCSO tKSO tDCSOF 0.8VDD SO0 SO1 Output data 0.2VDD – 22 – CXP847P60 Serial transfer (CH2) Item (Ta = –10 to +75°C, VDD = 4.5 to 5.5V, Vss = 0V reference) Symbol Pin tKCY SCK2 SCK High and Low level widths tKH tKL SCK2 SI input setup time (for SCK↑) tSIK SI2 SI input hold time (for SCK↑) tKSI SI2 SCK↓ → SO delay time tKSO SO2 SCK cycle time Conditions Input mode Min. Max. Unit 1000 ns 8000/fc ns 400 ns 4000/fc – 50 ns SCK input mode 100 ns SCK output mode 200 ns SCK input mode 200 ns SCK output mode 100 ns Output mode Input mode Output mode SCK input mode 200 ns SCK output mode 100 ns Note 1) tsys indicates three values according to the contents of the clock control register (CLC: 00FEH) upper 2 bits (CPU clock selection). tsys [ns] = 2000/fc (Upper 2 bits = “00”), 4000/fc (Upper 2 bits = “01’), 16000/fc (Upper 2 bits = “11”) Note 2) SCK, SI and SO represent SCK2, SI2 and SO2 for CH2, respectively. Note 3) The load of SCK2 output mode and SO2 output delay time is 50pF+1TTL. Serial transfer (CH2) Item (Ta = –10 to +75°C, VDD = 3.0 to 3.6V, Vss = 0V reference) Symbol Pin tKCY SCK2 SCK High and Low level widths tKH tKL SCK2 SI input setup time (for SCK↑) tSIK SI2 SI input hold time (for SCK↑) tKSI SI2 SCK↓ → SO delay time tKSO SO2 SCK cycle time Conditions Input mode Min. Max. Unit 1000 ns 8000/fc ns 400 ns 4000/fc – 100 ns SCK input mode 100 ns SCK output mode 200 ns SCK input mode 200 ns SCK output mode 100 ns Output mode Input mode Output mode SCK input mode 250 ns SCK output mode 125 ns Note 1) tsys indicates three values according to the contents of the clock control register (CLC: 00FEH) upper 2 bits (CPU clock selection). tsys [ns] = 2000/fc (Upper 2 bits = “00”), 4000/fc (Upper 2 bits = “01’), 16000/fc (Upper 2 bits = “11”) Note 2) SCK, SI and SO represent SCK2, SI2 and SO2 for CH2, respectively. Note 3) The load of SCK2 output mode and SO2 output delay time is 50pF. – 23 – CXP847P60 Fig. 5. Serial transfer CH2 timing tKCY tKL tKH 0.8VDD SCK2 0.2VDD tSIK tKSI 0.8VDD SI2 Input data 0.2VDD tKSO 0.8VDD SO2 Output data 0.2VDD – 24 – CXP847P60 (3) A/D converter characteristics (Ta = –10 to +75°C, VDD = AVDD = 3.0 to 5.5V, Vss = AVSS = 0V reference) Item Symbol Pin Conditions Min. Typ. Resolution Linearity errror Zero transition voltage VZT∗1 Full-scale transition voltage VFT∗2 Ta = 25°C VDD = AVDD = AVREF = 5.0V VSS = AVSS = 0V Zero transition voltage VZT∗1 Full-scale transition voltage VFT∗2 Convertion time tCONV tSAMP Sampling time 8 Bits ±3 LSB 10 70 mV 4910 4970 5030 mV ±5 LSB –10 6.5 70 mV 3215 3280 3345 mV 26/fADC∗3 6/fADC∗3 Reference input voltage VREF AVREF Analog input voltage VIAN AN0 to AN7 µs AVDD – 0.5 AVDD V VDD = AVDD = 3.0 to 3.6V AVDD – 0.3 AVDD V 0 AVREF V AVREF VDD = 5.5V 0.6 1.0 mA VDD = 3.6V 0.4 0.7 mA 10 µA Sleep mode Stop mode IREFS µs VDD = AVDD = 4.5 to 5.5V Operation mode IREF AVREF current Unit –50 Linearity errror Ta = 25°C VDD = AVDD = AVREF = 3.3V VSS = AVSS = 0V Max. Fig.6. Definition of A/D converter terms ∗1 VZT: Value at which the digital conversion value changes from 00H to 01H and vice versa. ∗2 VFT: Value at which the digital conversion value changes from FEH to FFH and vice versa. ∗3 fADC indicates the below values due to the contents of bit 6 (CKS) of the A/D control register (ADC: 00F9H). PS1 selected fADC = fc PS2 selected fADC = fc/2 Digital conversion value FFH FEH Linearity error 01H 00H VFT VZT Analog input – 25 – CXP847P60 (4) Interruption, reset input (Ta = –10 to +75°C, VDD = 3.0 to 5.5V, Vss = 0V reference) Item Symbol Pin External interruption High, Low level width tIH tIL INT0 INT1 INT2 INT3 INT4 NMI Reset input Low level width tRSL RST Conditions Min. Max. Unit 1 µs 32/fc µs Fig. 7. Interruption input timing tIH INT0 INT1 INT2 INT3 INT4 NMI (NMI is specified only for the falling edge) tIL 0.8VDD 0.2VDD tIL tIH Fig. 8. RST input timing tRSL RST 0.2VDD (5) Power-on reset∗1 (Ta = –10 to +75°C, VDD = 4.5 to 5.5V, VSS = 0V reference) Item Symbol Power supply rise time tR tOFF Power supply cut-off time Pin Conditions Power-on reset VDD Min. Max. Unit 0.05 50 ms 1 Repetitive power-on reset ∗1 Power-on reset function is selected by the mask option. See the Selection Guide for the mask option. Power-on reset function can be selected only for the supply voltage range of 4.5 to 5.5V. Fig. 9. Power-on reset 4.5V VDD 0.2V 0.2V tR tOFF Turn the power on smoothly. – 26 – ms CXP847P60 Appendix Fig. 10. Recommended oscillation circuit for SPC700 Series AAAA AAAA AAAA (i) Main clock EXTAL XTAL Rd C1 C2 Manufacturer RIVER ELETEC CO., LTD. Model HC-49/U03 fc (MHz) C1 (pF) C2 (pF) 8.00 10 10 5 5 22 (15) 22 (15) 12.00 15 15 16.00 12 12 10.00 12.00 Rd (Ω) Circuit example 0 (i) 0 (i) 16.00 8.00 KINSEKI LTD. HC-49/U (-S) 10.00 Selection Guide Option item Mask CXP847P60Q-1- CXP847P60R-1- Reset pin pull-up resistor Non-existent/Existent Existent Existent Power-on reset function Non-existent/Existent∗1 Existent Existent ∗1 Power-on reset function "Existent" is not selected under the using condition in the range of VDD=3.0 to 4.5V. – 27 – CXP847P60 Characteristics Curve (Reference) IDD vs. fc (VDD = 5V, Ta = 25°C, Typical) IDD vs. VDD (fc = 16MHz, Ta = 25°C, Typical) 20 1/2 dividing mode 1/2 dividing mode 20.0 1/4 dividing mode 10.0 IDD – Supply current [mA] Sleep mode 1.0 0.5 0.1 (100µA) 0.05 (50µA) IDD – Supply current [mA] 1/16 dividing mode 5.0 15 1/4 dividing mode 10 5 1/16 dividing mode 0.01 (10µA) Stop mode Sleep mode 3 4 5 6 5 10 fc – System clock [MHz] 0 VDD – Supply voltage [V] IDD vs. VDD (fc = 12MHz, Ta = 25°C, Typical) 20.0 1/2 dividing mode 10.0 1/4 dividing mode 20 1.0 Sleep mode 0.5 0.1 (100µA) 0.05 (50µA) IDD vs. fc (VDD = 3.3V, Ta = 25°C, Typical) 15 1/16 dividing mode IDD – Supply current [mA] IDD – Supply current [mA] 5.0 16 10 1/2 dividing mode 5 1/4 dividing mode 0.01 (10µA) 1/16 dividing mode Sleep mode 3 6 4 5 VDD – Supply voltage [V] 0 1 – 28 – 5 10 fc – System clock [MHz] 15 CXP847P60 Unit: mm 100PIN QFP (PLASTIC) + 0.1 0.15 – 0.05 15.8 ± 0.4 + 0.4 14.0 – 0.01 17.9 ± 0.4 23.9 ± 0.4 + 0.4 20.0 – 0.1 A 0.65 + 0.35 2.75 – 0.15 ±0.12 M 0° to 15° DETAIL A 0.8 ± 0.2 (16.3) 0.15 PACKAGE STRUCTURE PACKAGE MATERIAL EPOXY RESIN SOLDER PLATING SONY CODE QFP-100P-L01 LEAD TREATMENT EIAJ CODE ∗QFP100-P-1420-A LEAD MATERIAL COPPER / 42 ALLOY PACKAGE WEIGHT 1.4g JEDEC CODE 100PIN LQFP (PLASTIC) 16.0 ± 0.2 ∗ 14.0 ± 0.1 75 51 76 (15.0) 50 0.5 ± 0.2 A 26 (0.22) 100 1 0.5 ± 0.08 + 0.08 0.18 – 0.03 25 + 0.2 1.5 – 0.1 + 0.05 0.127 – 0.02 0.1 0.1 ± 0.1 0° to 10° 0.5 ± 0.2 Package Outline DETAIL A NOTE: Dimension “∗” does not include mold protrusion. PACKAGE STRUCTURE PACKAGE MATERIAL EPOXY/PHENOL RESIN SONY CODE LQFP-100P-L01 LEAD TREATMENT SOLDER PLATING EIAJ CODE ∗QFP100-P-1414-A LEAD MATERIAL 42 ALLOY JEDEC CODE PACKAGE WEIGHT – 29 –