NSC DS22EV5110

DS22EV5110
May 11, 2009
DVI, HDMI Extended Reach Equalizer with Retimer and
Output De-Emphasis
General Description
Features
The DS22EV5110 is a 6.75 Gbps (3 x 2.25 Gbps) extended
reach equalizer optimized for DVI™and HDMI™ cable extension applications with a high performance re-clocking feature.
It supports 3 Transition Minimized Differential Signaling
(TMDS®) data channels and a single clock channel over
DVI™ v1.0, and HDMI™ v1.3a data rates up to 2.25 Gbps for
each data channel. The device incorporates a configurable
receive equalizer, a clock and data recovery (CDR) circuit and
a de-emphasis driver on each data channel over DVI v1.0,
and HDMI v1.3a data rates up to 2.25 Gbps for each data
channel. The device incorporates a configurable receive
equalizer with a clock and data recovery (CDR) circuit on each
data channel. The clock channel feeds a high-perfromance
phase locked loop (PLL) that regenerates a low jitter output
clock for data recovery, enabling the extended reach of driving capability feature for repeater application.
The DS22EV5110 equalizes greater than 25 meters 28 AWG
of HDMI cable, enabling 1080p resolution with 12 bit deep
color depth (2.25 Gbps), to a low jitter version of the clock and
data signal outputs, reducing both deterministic and random
jitter. Obtaining total jitter is 0.09 UI or less over the supported
data rates. This extremely low level of output jitter provides
system designers with extra margin and flexibility when working with stringent timing budgets. It is ideal for the DVI and
HDMI source and repeater applications.
The transmitter supports configurable transmit de-emphasis
so the output can be optimized for driving additional lengths
of cables or FR4 traces.
■ Optimized for HDMI/DVI source and repeater applications
■ TMDS compatible inputs with configurable receive
equalization supporting data rates up to 2.25 Gbps
■ TMDS compatible outputs with configurable transmit deemphasis
■ Dedicated CDR on each data channel reduces jitter
transfer
■ Resistor adjustable differential output voltage for AC
■
■
■
■
■
■
coupled Cat5e and Cat6 extension applications
2 equalizer settings for a wide range of cable reaches up
to 2.25 Gbps
Total Output Jitter of 0.09 UI at 2.25 Gbps
DVI 1.0 and HDMI v1.3a compatible TMDS source and
sink interface
7 mm x 7 mm 48 pin LLP package
>8 kV HBM ESD protection
0 °C to +70 °C operating temperature
Applications
■ Repeater Applications
— HDMI / DVI Extender
■ Source Applications
— Video Cards
— Blu-ray DVD Players
— Game Consoles
■ Sink Applications
— High Definition Displays
— Projectors
Application Diagram
30094953
© 2009 National Semiconductor Corporation
300949
www.national.com
DS22EV5110 DVI, HDMI Extended Reach Equalizer with Retimer and Output De-Emphasis
PRELIMINARY
DS22EV5110
Pin Descriptions
Pin Name
Pin Number
I/O, Type
Description
High Speed Differential I/O
C_IN−
C_IN+
1
2
I, CML
Inverting and non-inverting TMDS Clock inputs to the equalizer. An on-chip 50 Ω terminating
resistor connects C_IN+ to VDD and C_IN- to VDD.
D_IN0−
D_IN0+
4
5
I, CML
Inverting and non-inverting TMDS Data inputs to the equalizer. An on-chip 50 Ω terminating
resistor connects D_IN0+ to VDD and D_IN0- to VDD.
D_IN1−
D_IN1+
8
9
I, CML
Inverting and non-inverting TMDS Data inputs to the equalizer. An on-chip 50 Ω terminating
resistor connects D_IN1+ to VDD and D_IN1- to VDD.
D_IN2−
D_IN2+
11
12
I, CML
Inverting and non-inverting TMDS Data inputs to the equalizer. An on-chip 50 Ω terminating
resistor connects D_IN2+ to VDD and D_IN2- to VDD.
C_OUTC_OUT+
36
35
O, CML
Inverting and non-inverting TMDS outputs from the equalizer. Open collector.
D_OUT0−
D_OUT0+
33
32
O, CML
Inverting and non-inverting TMDS outputs from the equalizer. Open collector.
D_OUT1–
D_OUT1+
29
28
O, CML
Inverting and non-inverting TMDS outputs from the equalizer. Open collector.
D_OUT2−
D_OUT2+
26
25
O, CML
Inverting and non-inverting TMDS outputs from the equalizer. Open collector.
Equalization Control
EQ2
EQ1
EQ0
37
38
39
I, LVCMOS EQ2, EQ1 and EQ0 select the equalizer boost level for EQ channels. Internally pulled LOW
as default. See Table 1.
De-Emphasis Control
DE1
DE0
42
43
I,
LVCMOS
DE1, DE0 select the DE-emphasis level for output drivers. Internally pulled low as default.
Refer to Table 2.
BYPASS
47
I,
LVCMOS
Reclocker enable control. Internally pulled low as default.
H = Reclock and De-Emphasis function is bypassed.
L = Normal operation.
EN
44
I, LVCMOS Enable Output Drivers. Internally pulled HIGH as default.
H = normal operation (enabled).
L = standby mode.
SD
45
O, LVCMOS Signal Detect Output pin.
H = signal detected on all channels.
L = no signal detected on one or more channels.
LOCK
14
O, LVCMOS Lock Indicator Output pin.
H = PLL is locked.
L = PLL is not locked.
VOD_CRL
48
I,
Analog
VOD control pin. Refer to Table 3. See Functional Description.
External resistance = 24 kΩ to GND, Output DC Coupled Application.
External resistance = 12 kΩ to GND, Output AC Coupled Application.
LFp
LFn
40
41
I,
Analog
Loop filter capacitor pins.
See Functional Description.
VDD
3, 6, 7,
10, 13,
15, 46
Power
VDD = 3.3 V ±5%. VDD pins should be tied to the VDD plane through a low inductance path.
A 0.1 µF bypass capacitor should be connected between each VDD pin to the GND planes.
See Power Supply Bypassing for additional details.
GND
22, 24,
27, 30,
31, 34
GND
Ground reference. GND should be tied to a solid ground plane through a low impedance
path.
DAP
GND
Ground reference. The exposed pad at the center of the package must be connected to the
ground plane.
Device Control
Power
Exposed
DAP
www.national.com
2
Pin Number
I/O, Type
DS22EV5110
Pin Name
Description
Other
Reserv
16, 17,
18, 19,
20,21,
23
Note: I = Input, O = Output,
Reserved. Do not connect. Leave open.
IO =Input/Output,
Connection Diagram
30094952
TOP VIEW — Not to Scale
Ordering Information
NSID
Package
Tape & Reel QTY
Package Number
DS22EV5110SQE
48 Lead LLP
250
SQA48A
DS22EV5110SQ
48 Lead LLP
1000
SQA48A
DS22EV5110SQX
48 Lead LLP
2,500
SQA48A
3
www.national.com
DS22EV5110
Absolute Maximum Ratings (Note 1)
ESD Rating
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
HBM, 1.5 kΩ, 100 pF
Thermal Resistance
θJA, No Airflow
Supply Voltage (VDD)
LVCMOS Input Voltage
LVCMOS Output Voltage
CML Input/Output Voltage
Junction Temperature
Storage Temperature
Lead Temp. (Soldering, 5 sec.)
-0.5V to 4.0 V
-0.5V to (VDD+ 0.5) V
-0.5V to (VDD+ 0.5) V
-0.5V to (VDD+ 0.5) V
+125°C
-65°C to +150°C
+260°C
>8 kV
33°C/W
Recommended Operating
Conditions (Notes 3, 4)
Supply Voltage
(VDD to GND)
Supply Noise Tolerance
(100 Hz to 50 MHz)
Ambient Temperature
Min
3.135
Typ
3.3
Max
3.465
Units
V
100
0
25
mVp-p
+70
°C
Electrical Characteristics
Over recommended operating supply and temperature ranges unless otherwise specified. All parameters are guaranteed by test,
statistical analysis, or design unless otherwise specified. (Note 3)
Symbol
Parameter
Condition
Min
Typ
Max
Unit
Power
P
Power Supply
Consumption
EN = H, Device Enabled
PRBS15 pattern, fCLK=225
MHz
RT= 50Ω to AVCC, Figure 2
1000
1150
mW
EN = L, Standby Mode
PRBS15 pattern, fCLK=225
MHz
RT= 50Ω to AVCC, Figure 2
750
900
mW
LVCMOS / LVTTL DC Specifications
VIH
High level input
voltage
2
VDD
V
VIL
Low level input
voltage
GND
0.8
V
VOH
High level output
voltage
IOH = -3 mA
VOL
Low level output
voltage
IOL = 3 mA
IIH
2.4
VIN = VDD, EQ2, EQ1, EQ0,
DE1, DE0, BYPASS pins
Input HighCurrent
(pull down)
VIN = VDD, EN pin (pull up)
IIL
V
0.4
V
60
mA
-15
mA
VIN = 0 V, EQ2, EQ1, EQ0,
DE1, DE0, BYPASS pins
Input Low Current
(pull down)
15
VIN = 0 V, EN pin (pull up)
μA
μA
-20
Signal Detect
SDH
Default Input signal level to
Signal Detect High assert SD pin
80
mVp-p
SDL
Default Input signal level to
Signal Detect Low deassert SD
20
mVp-p
www.national.com
4
Parameter
Condition
Min
Typ
Max
Unit
VTX
Input Voltage
Swing (Launch
Amplitude)
Measured differentially at
TPA, Figure 1, note 4
800
1000
1560
mVp-p
VICMDC
Input CommonMode Voltage
DC-Coupled requirement
Measured at TPB,
VINmin=800mV,
VINmax=1200mV, Figure 1
VDD-0.3
VDD-0.2
V
VIN
Input Voltage
Sensitivity
Measured differentially at
TPB, Figure 1
2.25 Gbps, Clock Pattern
150
1560
mVp-p
RIN
Input resistance
IN+ to VDD and IN- to VDD
40
60
Ohms
RLI
Differential output
100 MHz — 1125 MHz
return loss
CML Inputs
50
10
dB
CML Outputs
Measured DC outputs at
TPC, RT = 50Ω when DUT
VDD is off with OUT+ and
OUT- terminated by RT=
50Ω to AVCC, Figure 2
VOFF
Standby Output
Voltage
VO
External resistor = 24 kΩ at
VOD_CRL pin.Measured
Differential Output differentially with OUT+ and
OUT- terminated by
voltage swing
RT=50Ω to AVCC,Figures 2,
3
VOCM
Output commonmode Voltage
Measured single-ended,
> 1.65 Gbps, Figure 2
tR, tF
Transition time
20% to 80% of differential
output voltage, measured
within 1” from output pins,
Figure 3
85
tCCSK
Inter Pair Data
Channel-toChannel Skew (all
3 data channels)
Difference in 50% crossing
between channels
2.25 Gbps, Clock Pattern
(Note 4)
2
tPPSK
Inter Pair Data
Channels ParttoPart Skew
Difference in 50% crossing
between channels of any two
devices
2.25 Gbps, Clock Pattern
50
ps
tDD
Data Channels
Latency
2.25 Gbps, Clock Pattern,
Figure 4
400
ps
tCD
Clock Channel
Latency
2.25 Gbps, Clock Pattern,
Figure 4
600
ps
4
ms
AVCC- 10
AVCC+ 10
mV
800
1200
mVp-p
AVCC- 0.35
AVCC- 0.2
V
ps
3
ps
LVCMOS Outputs
tSL
SD to LOCK time
Figure 4
fCLK
Clock Frequency
Clock Path
(Note 4)
25
250
MHz
bR
Bit Rate
Data Paths
(Note 4)
0.25
2.25
Gbps
Bit Rate
5
www.national.com
DS22EV5110
Symbol
DS22EV5110
Symbol
Parameter
Condition
Min
Typ
Max
Unit
Data Channel Random Jitter
RJ
Random Jitter
(Notes 4, 5, 6)
3
psrms
Data Channel CDR Jitter Generation
TROJ1
Data Paths, measured at
Total Output Jitter
TPC PRBS7, EQ [2:0] = 000
0.25 Gbps
Figure 1, (Notes 4, 5, 6)
0.03
0.05
UIp-p
TROJ2
Data Paths, measured at
Total Output Jitter
TPC PRBS7, EQ [2:0] = 000
1.65 Gbps
Figure 1, (Notes 4, 5, 6)
0.08
0.14
UIp-p
TROJ3
Data Paths, measured at
Total Output Jitter
TPC PRBS7, EQ [2:0] = 000
2.25 Gbps
Figure 1, (Notes 4, 5, 6)
0.09
0.16
UIp-p
BWLOOP
CDR Loop
Bandwidth
0.25 Gbps data rate
0.25
MHz
1.65 Gbps data rate
1.65
MHz
2.25 Gbps data rate
2.25
MHz
Clock Channel PLL Jitter Generation
TROJ4
Clock Path, measured at
Total Output Jitter TPC
25 MHz
Figure 1
(Notes 4, 5, 6)
0.03
0.045
UIp-p
TROJ5
Clock Path, measured at
Total Output Jitter TPC
165 MHz
Figure 1
(Notes 4, 5, 6)
0.07
0.13
UIp-p
TROJ6
Clock Path, measured at
Total Output Jitter TPC
225 MHz
Figure 1
(Notes 4, 5, 6)
0.08
0.135
UIp-p
Note 1: “Absolute Maximum Ratings” are the ratings beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the device
should be operated at these limits.
Note 2: Allowed supply noise (mVp-p sine wave) at typical condition.
Note 3: Typical parameters are measured at VDD = 3.3 V, TA = 25 °C. They are for reference purposes, and are not production-tested.
Note 4: Parameter is guaranteed by statistical analysis and/or design.
Note 5: Deterministic jitter is measured at the differential outputs (TPC of Figure 1), minus the deterministic jitter before the test channel (TPA of Figure 1). Random
jitter is removed through the use of averaging or similar means.
Note 6: Total Jitter is defined as peak-to-peak deterministic jitter from + 12 times random jitter (ps).
Note 7: Random jitter contributed by the equalizer is defined as sq rt (JOUT2 − JIN2). JOUT is the random jitter at equalizer outputs in ps-rms, see TPC of Figure
1; JIN is the random jitter at the input of the equalizer in ps-rms, see TPA of Figure 1.
www.national.com
6
DS22EV5110
Setup and Timing Diagrams
30094910
FIGURE 1. Test Setup Diagram
30094912
FIGURE 2. CML Output Swings at A/B (VOD_CRL = 24 kΩ
7
www.national.com
DS22EV5110
30094911
FIGURE 3. CML Output Transition Times
30094913
FIGURE 4. CML Latency Delay Time
30094914
FIGURE 5. SD – LOCK Delay Time
www.national.com
8
The DS22EV5110 DVI, HDMI Extended Reach Equalizer with
Retimer and Output De-Emphasis consists of three data
30094915
FIGURE 6. Block Diagram
pins (EQ [2:0]). The range of boost settings provided enables
the DS22EV5110 to address a wide range of transmission line
path loss scenarios, enabling support for a variety of data
rates and formats. See Applications Information for recommended EQ settings.
PHASE-LOCKED-LOCKED LOOP (PLL)
The clock channel has a high-performance PLL that creates
a low jitter sampling clock for the clock and data recovery units
in the data channels. An external loop filter, composed of 2.2
nF (+ 5% tolerance) capacitor and a 3.3 kΩ (+ 5% tolerance)
resistor in series, are required between the LFp and the LFn
pins.
OUTPUT DE-EMPHASIS
De-emphasis is the conditioning function for use in compensating against backplane and cable transmission loss. The
DS22EV5110 provides four steps of de-emphasis ranging
from 0, 3, 6 and 9 dB, user-selectable dependent on the loss
profile of output channels. Table 2. shows the De-emphasis
control with default VO = 1000 mVp-p, and Figure 7. shows a
driver de-emphasis waveform.
CLOCK-DATA RECOVERY UNIT (CDR)
Each TMDS data channel has a CDR that operates independently from other TMDS data channels. Each CDR aligns the
sampling clock edges by digitally interpolating the clock from
PLL of the TMDS clock channel. The device is designed to
connect to DVI/HDMI compatible transmitter and receiver at
any data rate between 250 Mbps to 2.25 Gbps. The loop
bandwidth of the CDR is approximately baud_rate/1000, i.e.
2.25 MHz for 2.25 Gbps data.
OUTPUT VO CONTROL
Output differential voltage (VO) is controlled through
VOD_CRL pin ties an external resistor to the ground as shown
in Table 3. Users should restrict the external resistor values
used to be 12 kΩ to 24 kΩ. +5% tolerance is recommended.
INPUT EQUALIZATION
The input data channel equalizers support eight programmable levels of equalization boost Table 1 by the EQ
9
www.national.com
DS22EV5110
channels and a clock channel. Each data channel consists of
a TMDS compatible receiver with a power efficient equalizer,
a dedicated clock-data recovery (CDR) unit, and a TMDS
compatible transmitter.
Functional Description
DS22EV5110
TABLE 1. Equalization Control
INPUTS
RESULT
EQ2
EQ1
EQ0
Equalization in dB (1.125 GHz)
0
0
0
0 (default)
0
0
1
12
0
1
0
18
0
1
1
21
1
0
0
24
1
0
1
26
1
1
0
28
1
1
1
30
TABLE 2. De-Emphasis Control
INPUTS
RESULT
DE1
DE0
VO De-Emphasis level in mVpp
(VODE w/VOD_CRL = 24 kΩ
0
0
1000 (default)
0 (default)
0
1
710
-3
1
0
500
-6
1
1
355
-9
VO De-Emphasis in dB
TABLE 3. VO Control
External Resistor Value
(VOD_CRL pin)
Applications
VO Level (mVp-p)
24 kΩ
DC Coupled
1000
12 kΩ
AC Coupled
1000
30094916
FIGURE 7. Output De-Emphasis Differential Waveform (showing all de-emphasis steps)
www.national.com
10
SIGNAL DETECT
The DS22EV5110 features a signal detect circuit on all channels. The status of the input signals can be determined by the
state of the SD pin. A logic HIGH indicates the presence of
signals that have exceeded a specified maximum threshold
value (called SD_ON) on all channels. A logic LOW means
that the signals have fallen below a minimum threshold value
(called SD_OFF) on one or more channels.
DEVICE STATE AND ENABLE CONTROL
The DS22EV5110 has an Enable feature which provides the
ability to control device power consumption. This feature can
be controlled via the Enable Pin (EN Pin). If Enable is activated, the data channels and clock channel are placed in the
ACTIVE state and all device blocks function as described.
The DS22EV5110 can also be placed in STANDBY mode to
save power. In this mode, the output drivers of the device are
disabled. The CML outputs are in the HIGH (AVCC) state. All
LVCMOS outputs are in the HiZ state.
AUTOMATIC ENABLE FEATURE
During normal operation (i.e. BYPASS pin is LOW), the
DS22EV5110 can be configured to automatically enter
STANDBY mode, if the PLL of the DS22EV5110 is not locked.
The STANDBY mode can be implemented by connecting the
LOCK DETECT (LOCK) pin to the external (LVCMOS) Enable (EN) pin. If the LOCK pin is connected to the EN pin, a
logic HIGH on the LOCK pin will enable the device; thus the
DS22EV5110 will automatically enter the ACTIVE state. If the
PLL is unlocked, then the LOCK pin will be asserted LOW,
causing the aforementioned blocks to be placed in the
STANDBY state.
LOCK DETECT
When the PLL of the DS22EV5110 is locked, and the generated reference phases are successfully interpolated by the
CDR, this status is indicated by a logic HIGH on the LOCK
pin. The LOCK pin may be connected to the Enable (EN) pin
input to disable the data channels and clock channel when no
data signal is being received.
11
www.national.com
DS22EV5110
RETIMING AND DE-EMPHASIS BYPASS
The retiming and De-emphasis BYPASS pin provides the
flexibility to configure the device to an equalizer only mode.
The device is in normal operation, when holding a LOW state
on the BYPASS pin. The retiming and De-emphasis features
are disabled, when a HIGH state is applied.
DS22EV5110
vice, the output de-emphasis setting should be configured
based on the driving cable length. When used as the sink device, the levels of the equalization boost of the input data
channels should be optimized based on the receiving cable
length. The DS22EV5110 can also be used as a repeater in
an external extender box with the equalization and de-emphasis level settings optimized to provide the maximum cable
reach.
Application Information
The DS22EV5110 is a DVI/HDMI video signal reconditioning
device. The device conforms to DVI v1.0 and HDMI v1.3a
standards supporting up to 6.75 Gbps total throughput TMDS
data for 1080p with 36 bit deep color depth.
TYPICAL APPLICATION
The DS22EV5110 is used as a DVI/HDMI source device, sink
device, or a repeater device, see Figure 8. As the source de-
30094953
FIGURE 8. Typical Application Diagram
ground potential difference, or to use one CAT5/6 cable between two chassis. To optimize the DS22EV5110 performance, the external resistance of 12 kΩ at the VOD_CRL pin
should be used on the Source DS22EV5110, and a pair of 50
Ω pull-up resistors should be placed close to the outputs of
the Source DS22EV5110, in order to DC bias the output driver. Meanwhile, 622Ω pull-down resistors should be placed at
the inputs of the Sink DS22EV5110 device, in order to set the
input common mode to a 3.05 V. Note AC coupled configuration is not compliant to the HDMI specification of Source
requirement (See Figure 10).
DC AND AC COUPLED APPLICATIONS
The DS22EV5110 is designed to support TMDS differential
pairs with DC coupled transmission lines. It contains integrated termination resistors (50Ω), pulled up to VDD at the input
stage, and open collector outputs for DVI / HDMI signaling.
Figure 9 shows the DC coupled connection between the HDMI Source (ie. DS22EV5110) and HDMI Sink (ie.
DS22EV5110) devices. In the DC coupled application, the
external resistance of 24 kΩ at VOD_CRL pin is used at the
Source to ensure the VO level of 1000 mVp-p. The AC coupled method connecting between the Source and the Sink
devices may be preferred to eliminate the impact of the
30094920
FIGURE 9. DC Coupled Application
www.national.com
12
DS22EV5110
30094921
FIGURE 10. AC Coupled Application
24 AWG UTP (LOW SKEW UNSHIELDED TWIST PAIRS)
CABLES
The DS22EV5110 can be used to extend the length of low
skew grade UTP cables, such as Cat5e and Cat6 to distances
greater than 30 meters at 1.65 Gbps with < 0.20 UI of jitter.
Note that for non-standard DVI/HDMI cables, the user must
ensure the inter pair skew requirements are met. Table 5
shows the recommended EQ control settings for various data
rates and cable lengths for UTP configurations.
CABLE SELECTION AND INTER-PAIR SKEW
DVI v1.0 and HDMI v1.3a specify Inter-Pair Skew requirements for the system. The DS22EV5110 intends to extend the
longer cable reach with STP (DVI / HDMI) cable, or UTP
(Cat5 / Cat5e / Cat6) cable, and it does not have a de-skew
function to compensate any cable Inter-Pair Skews. Long cable with Inter-Pair Skew exceeding the DVI / HDMI standard
limit tolerance could cause system distortion. Therefore, National suggests the consideration of Inter-Pair Skew budget
during the system design, and recommends Low-Skew Video
grade cables for cable extending applications.
TABLE 5. EQ Control Setting for UTP Cable
Format (Data Rate)
28 AWG STP (SHIELDED TWIST PAIRS) DVI / HDMI
CABLES RECOMMENDED EQ SETTINGS
Table 4 provides the recommended EQ control settings for
various data rates and cable lengths for 28 AWG DVI/HDMI
compliant configurations. The EQ setting is made via three
EQ [2:0] pins.
0 ~ 10m
> 10m
1080P 36-bit (2.25 Gbps) Setting 0x01
Setting 0x05
1080P (1.65 Gbps)
Setting 0x01
Setting 0x05
1080I (750 Mbps)
Setting 0x05
Setting 0x05
TABLE 4. EQ Control Setting for STP Cable
Format (Data Rate)
0 ~ 10m
> 10m
1080P 36-bit (2.25 Gbps)
Setting 0x01
Setting 0x06
1080P (1.65 Gbps)
Setting 0x01
Setting 0x06
1080I (750 Mbps)
Setting 0x06
Setting 0x06
13
www.national.com
DS22EV5110
POWER SUPPLY BYPASSING
Two approaches are recommended to ensure the
DS22EV5110 is provided with an adequate power supply.
First, the supply (VDD) and ground (GND) pins should be
connected to power planes routed on adjacent layers of the
printed circuit board. The layer thickness of the dielectric
should be minimized so the VDD and GND planes create a
low inductance supply with distributed capacitance. Second,
careful attention to supply bypassing through the proper use
of bypass capacitors is required. A 0.1 μF bypass capacitor
should be connected to each VDD pin such that the capacitor
is placed as close as possible to the DS22EV5110. Smaller
body size capacitors can help facilitate proper component
placement. Additionally, two capacitors with capacitance in
the range of 2.2 μF to 10 μF should be incorporated in the
power supply bypassing design as well. These capacitors can
be either tantalum or an ultra-low ESR ceramic and should be
placed as close as possible to the DS22EV5110.
General Recommendations
The DS22EV5110 is a high performance circuit capable of
delivering excellent performance. To achieve optimal performance, careful attention must be paid to the details associated with high-speed design as well as providing a clean
power supply. Refer to the LVDS Owner’s Manual for more
detailed information on high-speed design tips as well as
many other available resources addressing signal integrity
design issues.
PCB LAYOUT CONSIDERATIONS FOR DIFFERENTIAL
PAIRS
The TMDS differential inputs and outputs must have a controlled differential impedance of 100 Ω. It is preferable to route
TMDS lines exclusively on one layer of the board, particularly
for the input traces. The use of vias should be avoided if possible. If vias must be used, they should be used sparingly and
must be placed symmetrically for each side of a given differential pair. Route the TMDS signals away from other signals
and noise sources on the printed circuit board. All traces of
TMDS differential inputs and outputs must be equal in length
to minimize intra-pair skew.
EQUIVALENT I/O STRUCTURES
Figure 14 shows the DS22EV5110 CML output structure and
ESD protection circuitry.
Figure 15 shows the DS22EV5110 CML input structure and
ESD protection circuitry.
LLP FOOTPRINT RECOMMENDATIONS
See National application note: AN-1187, “Leadless Leadframe Package (LLP)” for additional information on LLP packages footprint and soldering information.
30094922
FIGURE 11. Equivalent Output Structure
30094923
FIGURE 12. Equivalent Input Structure
www.national.com
14
DS22EV5110
Typical Performance Characteristics as a Repeater
30094909
FIGURE 13. Simplified Test Setup as a Single Repeater
30094960
30094961
FIGURE 14. System Source Eye Diagram at TPA
(2.25 Gbps)
FIGURE 15. Device Sink Eye Diagram at TPB
(2.25 Gbps, Cable A = 25m 28 AWG HDMI)
30094963
30094962
FIGURE 17. Device Source Eye Diagram at TPC
(2.25 Gbps, Cable A = 25m 28 AWG HDMI,
EQ = 0x05, BYPASS = 0, DE = -3dB)
FIGURE 16. Device Source Eye Diagram at TPC
(2.25 Gbps, Cable A = 25m 28 AWG HDMI,
EQ = 0x05, BYPASS = 0, DE = 0dB)
30094964
FIGURE 18. System Sink Eye Diagram at TPD
(2.25 Gbps, Cable A = 25m 28 AWG HDMI, Cable B = 7.5m
28AWG HDMI, EQ = 0x05, BYPASS = 0, DE = -3dB)
15
www.national.com
DS22EV5110
30094965
30094966
FIGURE 19. System Source Eye Diagram at TPA
(1.65 Gbps)
FIGURE 20. Device Sink Eye Diagram at TPB
(1.65 Gbps, Cable A = 35m 28 AWG HDMI)
30094967
30094968
FIGURE 21. Device Source Eye Diagram at TPC
(1.65 Gbps, Cable A = 35m 28 AWG HDMI,
EQ = 0x05, BYPASS = 0, DE = 0dB)
FIGURE 22. Device Source Eye Diagram at TPC
(1.65 Gbps, Cable A = 35m 28 AWG HDMI,
EQ = 0x05, BYPASS = 0, DE = -6dB)
30094969
FIGURE 23. System Sink Eye Diagram at TPD
(1.65 Gbps, Cable A = 35m 28 AWG HDMI, Cable B = 10m
28AWG HDMI, EQ = 0x05, BYPASS = 0, DE = -6dB)
www.national.com
16
DS22EV5110
Physical Dimensions inches (millimeters) unless otherwise noted
7mm x 7mm 48-pin LLP Package
Order Number DS22EV5110SQ
Package Number SQA48A
17
www.national.com
DS22EV5110 DVI, HDMI Extended Reach Equalizer with Retimer and Output De-Emphasis
Notes
For more National Semiconductor product information and proven design tools, visit the following Web sites at:
Products
Design Support
Amplifiers
www.national.com/amplifiers
WEBENCH® Tools
www.national.com/webench
Audio
www.national.com/audio
App Notes
www.national.com/appnotes
Clock and Timing
www.national.com/timing
Reference Designs
www.national.com/refdesigns
Data Converters
www.national.com/adc
Samples
www.national.com/samples
Interface
www.national.com/interface
Eval Boards
www.national.com/evalboards
LVDS
www.national.com/lvds
Packaging
www.national.com/packaging
Power Management
www.national.com/power
Green Compliance
www.national.com/quality/green
Switching Regulators
www.national.com/switchers
Distributors
www.national.com/contacts
LDOs
www.national.com/ldo
Quality and Reliability
www.national.com/quality
LED Lighting
www.national.com/led
Feedback/Support
www.national.com/feedback
Voltage Reference
www.national.com/vref
Design Made Easy
www.national.com/easy
www.national.com/powerwise
Solutions
www.national.com/solutions
Mil/Aero
www.national.com/milaero
PowerWise® Solutions
Serial Digital Interface (SDI) www.national.com/sdi
Temperature Sensors
www.national.com/tempsensors SolarMagic™
www.national.com/solarmagic
Wireless (PLL/VCO)
www.national.com/wireless
www.national.com/training
PowerWise® Design
University
THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION
(“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY
OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO
SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS,
IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS
DOCUMENT.
TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT
NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL
PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR
APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND
APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE
NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS.
EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO
LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE
AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR
PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY
RIGHT.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR
SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and
whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected
to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform
can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness.
National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other
brand or product names may be trademarks or registered trademarks of their respective holders.
Copyright© 2009 National Semiconductor Corporation
For the most current product information visit us at www.national.com
National Semiconductor
Americas Technical
Support Center
Email: [email protected]
Tel: 1-800-272-9959
www.national.com
National Semiconductor Europe
Technical Support Center
Email: [email protected]
National Semiconductor Asia
Pacific Technical Support Center
Email: [email protected]
National Semiconductor Japan
Technical Support Center
Email: [email protected]