KOA FBA1J4BTTE221P

1733 Reader's Spreadspg189-328:1570 Reader's Spreadspg189-328
1/27/09
4:59 PM
Page 63
FBA
ferrite bead array
EU
features
• Noise suppression in signal I/O lines
and other circuits that require multiple
chip beads for noise suppression
• Multiple circuits in a single package
• Marking: Black body color with no marking
• Products with lead-free terminations meet
EU RoHS requirements
dimensions and construction
L
a
Type
p
(Inch Size Code)
b
W
1J
(0603)
L
W
Dimensions inches (mm)
t
a
b
p
.126±.008 .063±.008 .031±.008 .016±.008 .012±.008 .031±.008
(3.2±0.2) (1.6±0.2) (0.8±0.2) (0.40±0.2) (0.3±0.2) (0.8±0.2)
t
Protective
Coating
Solder
Plating
ordering information
New Part #
FBA
1J
4
A
Type
Size
Circuits
Characteristics
1J: 0603
Number
of
circuits
A: Standard
B: High speed
T
Termination
Material
T: Sn
TE
300
P
Packaging
Impedance
Tolerance
TE: 7" embossed
plastic
(3,000
pieces/reel)
2 significant
figures + 1
multiplier
Ex: 300 = 30Ω
P: ±25%
EMI/EMC
filtering
circuit schematic
For further information on packaging,
please refer to Appendix A.
Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.
258
2/24/08
KOA Speer Electronics, Inc. • 199 Bolivar Drive • Bradford, PA 16701 • USA • 814-362-5536 • Fax: 814-362-8883 • www.koaspeer.com
1733 Reader's Spreadspg189-328:1570 Reader's Spreadspg189-328
1/27/09
4:59 PM
Page 64
PMS 300 neg.
Black neg.
FBA
ferrite bead array
applications and ratings
NEW
Impedance
@ 100MHz
(Ω)
FBA1J4ATTE300P
FBA1J4ATTE600P
FBA1J4ATTE121P
FBA1J4ATTE221P
FBA1J4ATTE301P
FBA1J4ATTE601P
FBA1J4ATTE102P
FBA1J4BTTE300P
FBA1J4BTTE600P
FBA1J4BTTE121P
FBA1J4BTTE221P
FBA1J4BTTE301P
FBA1J4BTTE601P
30
60
120
220
300
600
1000
30
60
120
220
300
600
DC
Resistance
Maximum
(Ω)
0.1
0.25
0.3
0.4
0.5
0.7
0.25
0.3
0.4
0.45
0.50
0.65
Allowable
DC Current
Per Element
Maximum (mA)
200
400
350
Operating
Temperature
Range
250
100
200
400
350
-55°C to +125°C
100
150
100
environmental applications
Performance Characteristics
Requirement
Parameter
Test Method
Operating Temperature
-55°C to +125°C
Storage Temperature
40°C @ 70% humidity
Sealed plastic bags with desiccant shall be used to
reduce the potential of oxidation on the terminations
during storage.
Resistance to Solder Heat
Change in Impedance: Relative to value before
test ±20%
Appearance: There shall be no cracking.
Solder Coverage: More than 75% of the terminal
electrode shall be covered with solder.
Flux: 5 - 10 second dip
After Flux: Air dry for 15 seconds
Preheat: 150°C ± 10°C
Preheat Time: 60 seconds
Solder Temperature: 260°C ± 5°C
Dip Time: 10 ± 1 second
Solderability
Solder Coverage: More than 95% of the termination
shall be covered with solder.
Flux: 5 - 10 second dip
After Flux: Air dry for 15 seconds
Solder Temperature: 245°C ± 5°C
Dip Time: 5 ± 0.5 second
Leach Resistance
Appearance: There shall be no visible signs of
physical or mechanical damage (i.e. no cracks).
Terminations: Termination must not be leached
away for more than 5%.
The bead shall be subjected to the following 5 steps
for the period of time shown below. The 5 steps
constitute one (1) rotation. 4 rotations shall be
carried out.
1) Flux: 5 - 10 seconds
2) After Flux: Air dry for 15 seconds
3) Solder Temperature: 230°C ± 5°C
4) Dip Time: 5 ± 0.5 second
5) Cool: Air cool for 60 seconds
Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.
3/05/07
KOA Speer Electronics, Inc. • 199 Bolivar Drive • Bradford, PA 16701 • USA • 814-362-5536 • Fax: 814-362-8883 • www.koaspeer.com
259
EMI/EMC
filtering
NEW
Part
Designation
1733 Reader's Spreadspg189-328:1570 Reader's Spreadspg189-328
1/27/09
4:59 PM
Page 65
FBA
ferrite bead array
environmental applications (continued)
Performance Characteristics
Parameter
Requirement
Test Method
EMI/EMC
filtering
Insulation Resistance
Insulation Resistance: Min. 1G ohms
Solvent Resistance
Change in Impedance: Relative to value before
test ±10%
Cleaning by:
Washer: Ultrasonic washer (100W)
Solvent: Isopropyl alcohol
Time: 3 minutes
Terminal Strength
(hanging test)
Appearance: The terminal electrode shall not break
off, nor shall there be damage to the body.
Type:
1206
W(kgf):
1.5
Time:
30 seconds ± 2 seconds
Terminal Strength
(push test)
Appearance: There shall be no evidence of
mechanical degradations to terminals or body.
Type:
1206
W(kgf):
2.3
Time:
60 seconds
Bending Strength
Appearance: There shall be no physical
or mechanical damage.
Impedance: Relative to initial value
before test ±10%
Board: 90 x 40 x 1.6mm
Bend: 1mm
Time: 5 sec
Mechanical Shock
Appearance: There shall be no physical
or mechanical damage.
Impedance: Relative to initial value
before test ±10%
Force: 50G
Time: 11 msec
There shall be 3 shocks in each of 6 directions
(18 shocks total)
Vibration
Impedance: Relative to initial value ±10%
Only endurance conditioning by sweeping shall
be made. The entire frequency range from
10 - 2,000 Hz, return to 10 Hz in 20 minutes
(this will constitute one cycle).
Amplitude: 15G
The test shall have a 15G peak and shall be
applied for a period of 4 hours (12 cycles) in each
of 3 mutually perpendicular directions (a total of
36 cycles within a total of 12 hours).
Thermal Shock
Appearance: There shall be no physical
or mechanical damage.
Impedance: Relative to initial value ±20%
DCR: The DCR shall not exceed initial specified value.
Testing of the parts will be made at 0 hours, 250
hours and 500 hours. Before testing, the parts shall
be allowed to cool to room temperature for 24 hours.
Step:
Temperature:
Time:
1-start
-40°C ± 2°C
—
2-hold
-40°C ± 2°C
30 minutes ± 5 minutes
3-transfer —
0.5 minutes maximum
4-hold
±105°C ± 2°C 30 minutes ± 5 minutes
5-transfer —
0.5 minutes maximum
Steps 1 thru 5 constitute one complete cycle and the
test shall consist of a total of 500 cycles.
Load Humidity
Appearance: There shall be no physical
or mechanical damage.
Impedance: Relative to initial value ±15%
Measurements shall be taken at 0 hours, 250 hours,
500 hours and 1,000 hours and shall meet the
conditions stated above.
Temperature: ±85°C ± 2°C
Relative Humidity: 85%
Time: 1,000 hours total
Apply: 100% rated current
Life Test
Appearance: There shall be no physical
or mechanical damage.
Impedance: Relative to initial value ±15%
Measurements shall be taken at 0 hours, 250 hours,
500 hours and 1,000 hours and shall meet the
conditions stated above.
Temperature: ±85°C ± 2°C
Time: 1,000 hours total
Apply: 100% rated current
Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.
260
3/01/07
KOA Speer Electronics, Inc. • 199 Bolivar Drive • Bradford, PA 16701 • USA • 814-362-5536 • Fax: 814-362-8883 • www.koaspeer.com