VS-FCSP0530ETR www.vishay.com Vishay Semiconductors FlipKY®, 0.5 A FEATURES • Ultralow VF to footprint area • • • • Very low profile (< 0.6 mm) Low thermal resistance Supplied tested and on tape and reel Designed for consumer level APPLICATIONS • • • • • FlipKY® Reverse polarity protection Current steering Freewheeling Flyback Oring DESCRIPTION FlipKY® product family utilizes wafer level chip scale packaging to deliver Schottky diodes with the lowest VF to PCB footprint area in the industry. The three pad 0.9 mm x 1.2 mm devices can deliver up to 0.5 A and occupy only 1.08 mm2 of board space. The anode and cathode connections are made through solder bump pads on one side of the silicon rather than through protruding leads enabling designers to strategically place the diodes on the PCB. This design not only minimizes board space but also reduces thermal resistance and inductance, which can improve overall circuit efficiency. PRODUCT SUMMARY IF(AV) 0.5 A VR 30 V VF at IF 0.33 V IRM max. at 25 °C 50 μA IRM max. at 125 °C 15 mA TJ max. 150 °C EAS 5 mJ Typical applications include hand-held, portable equipment such as cell phones, MP3 players, PDAs, and portable hard disk drives where space savings and performance are crucial. MAJOR RATINGS AND CHARACTERISTICS SYMBOL IF(AV) CHARACTERISTICS Rectangular waveform VRRM VALUES UNITS 0.5 A 30 V IFSM tp = 5 μs sine 190 A VF 0.5 Apk, TJ = 125 °C 0.33 V TJ Range - 55 to 150 °C VS-FCSP0530ETR UNITS 30 V VOLTAGE RATINGS PARAMETER Maximum DC reverse voltage Maximum working peak reverse voltage Revision: 04-Jul-11 SYMBOL VR VRWM Document Number: 93429 1 For technical questions within your region: [email protected], [email protected], [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VS-FCSP0530ETR www.vishay.com Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS PARAMETER SYMBOL TEST CONDITIONS VALUES Maximum average forward current IF(AV) 50 % duty cycle at TPCB = 133 °C, rectangular waveform 0.5 Maximum peak one cycle non-repetitive surge current at TJ = 25 °C IFSM Non-repetitive avalanche energy EAS TJ = 25 °C, IAS = 2.0 A, L = 5.0 mH Repetitive avalanche current IAR Current decaying linearly to zero in 1 μs Frequency limited by TJ maximum VA = 1.5 x VR typical 5 µs sine or 3 µs rect. pulse 10 ms sine or 6 ms rect. pulse Following any rated load condition and with rated VRRM applied UNITS 190 A 10 5 mJ 0.5 A ELECTRICAL SPECIFICATIONS PARAMETER SYMBOL TEST CONDITIONS 0.5 A Maximum forward voltage drop See fig. 1 VFM (1) TJ = 25 °C 1A 0.5 A TJ = 125 °C 1A Maximum reverse leakage current See fig. 2 IRM (1) CT Maximum junction capacitance dV/dt Maximum voltage rate of charge TJ = 25 °C VR = Rated VR TJ = 125 °C TYP. MAX. UNITS 0.40 0.44 0.45 0.49 0.29 0.33 0.36 0.39 10 50 μA V 5 15 mA VR = 5 VDC (test signal range 100 kHz to 1 MHz), 25 °C - 90 pF Rated VR - 10 000 V/μs Note (1) Pulse width < 300 μs, duty cycle < 2 % THERMAL - MECHANICAL SPECIFICATIONS PARAMETER SYMBOL Maximum junction and storage temperature range TJ (1), TStg Typical thermal resistance, junction to PCB RthJL (2) Typical thermal resistance, junction to ambient RthJA (2) TEST CONDITIONS DC operation VALUES UNITS - 55 to 150 °C 35 °C/W 150 Notes (1) (2) dP tot 1 ------------- < -------------- thermal runaway condition for a diode on its own heatsink dT J R thJA Mounted on dual sided 0.58" square FR4 PCB with 0.2 square inches of 1 oz. top copper area Revision: 04-Jul-11 Document Number: 93429 2 For technical questions within your region: [email protected], [email protected], [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VS-FCSP0530ETR www.vishay.com Vishay Semiconductors TJ = 150 °C TJ = 125 °C TJ = 25 °C 1.0 160 Allowable Case Temperature (°C) IF - Instantaneous Forward Current (A) 10 DC 140 D = 3/4 D = 1/2 D = 1/3 D = 1/4 120 D = 1/5 100 Square wave (D = 0.50) 80 % VR applied See note (1) 0.1 80 0 0.2 0.4 0.6 0.8 1.0 0 1.2 0.6 0.8 Fig. 4 - Maximum Allowable Case Temperature vs. Average Forward Current (Per Leg) Fig. 1 - Maximum Forward Voltage Drop Characteristics (Per Leg) 0.3 10 Average Power Loss (W) 100 IR - Reverse Current (mA) 0.4 IF(AV) - Average Forward Current (A) VFM - Forward Voltage Drop (V) TJ = 150 °C TJ = 125 °C 1.0 TJ = 100 °C 0.1 TJ = 75 °C 0.01 TJ = 50 °C 0.001 TJ = 25 °C 0.0001 D = 0.20 D = 0.25 D = 0.33 D = 0.50 D = 0.75 0.2 RMS limit 0.1 DC 0 0 5 10 15 20 25 30 0 VR - Reverse Voltage (V) 0.2 0.4 0.6 0.8 IF(AV) - Average Forward Current (A) Fig. 5 - Forward Power Loss Characteristics (Per Leg) Fig. 2 - Typical Values of Reverse Current vs. Reverse Voltage (Per Leg) 1000 IFSM - Non-Repetitive Surge Current (A) 1000 CT - Junction Capacitance (pF) 0.2 TJ = 25 °C 100 10 100 10 At any rated load condition and with rated VRRM applied following surge 1 0 10 20 VR - Reverse Voltage (V) Fig. 3 - Typical Junction Capacitance vs. Reverse Voltage (Per Leg) 30 10 100 1000 10 000 tp - Square Wave Pulse Duration (µs) Fig. 6 - Maximum Non-Repetitive Surge Current (Per Leg) Note (1) Formula used: T = T - (Pd + Pd C J REV) x RthJC; Pd = Forward power loss = IF(AV) x VFM at (IF(AV)/D) (see fig. 6); PdREV = Inverse power loss = VR1 x IR (1 - D); IR at 80 % VR applied Revision: 04-Jul-11 Document Number: 93429 3 For technical questions within your region: [email protected], [email protected], [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VS-FCSP0530ETR www.vishay.com Vishay Semiconductors L D.U.T. IRFP460 Rg = 25 Ω Current monitor High-speed switch Freewheel diode + Vd = 25 V 40HFL40S02 Fig. 7 - Unclamped Inductive Test Circuit LINKS TO RELATED DOCUMENTS Dimensions www.vishay.com/doc?95049 Part marking information www.vishay.com/doc?95060 Packaging information www.vishay.com/doc?95062 Revision: 04-Jul-11 Document Number: 93429 4 For technical questions within your region: [email protected], [email protected], [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Outline Dimensions Vishay High Power Products FlipKY® 0.5 A/0.75 A DIMENSIONS in millimeters 0.520 0.460 0.500 0.071 0.125 0.105 Assignments 0.200 2 1 = Cathode 2 = Cathode 3 = Anode 1 0.300 0.700 1.244 1.244 3 0.300 0.300 0.173 0.400 0.395 0.355 0.914 Recommended footprint 0.500 PIN 2 cathode PIN 1 cathode 0.350 0.250 0.700 0.350 PIN 3 anode 0.450 Notes • Dimensioning and tolerancing per ASME Y14.5M-1994 • Controlling dimension: millimeter Document Number: 95049 Revision: 07-Sep-09 For technical questions concerning discrete products, contact: [email protected] For technical questions concerning module products, contact: [email protected] www.vishay.com 1 Legal Disclaimer Notice Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 11-Mar-11 www.vishay.com 1