The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. 0.2 mm Pitch, 0.9 mm above the board, Flexible Printed Circuit ZIF Connectors FH43B Series Space saving 2. 77 17. 8m m(8 1p sho wn) 0.9 os. Can be mounted over conductive traces. ■Features 1. Low-profile, small PCB mounting area Board footprint: Reduced approximately 45% Weight: Reduced approximately 55% (As compared with Hirose Electric's FH26 Series connectors 51 positions) 2. Easy solderability on the PC board No exposed contacts on the bottom of the connector Simple FPC insertion actuator The soldering leads are on 0.4 mm pitch, exiting on front and back of the connector. 3. Conducive traces on the PCB can run under the connector No exposed contacts on the bottom of the connector. 4. Easy FPC insertion and reliable electrical connection Proven Flip Lock actuator allows easy insertion of FPC and provides a tactile sensation when fully closed, confirming complete electrical and mechanical connection. 5. Easy FPC/FFC insertion FPC Lock FPC/FFC is self-guided in the connector assuring correct and reliable electrical and mechanical connection. 6. Accepts standard FPC thickness 0.2mm thick standard Flexible Printed Circuit (FPC) can be used. This is the only ultra-low profile ZIF connector using standard FPC. 7. Board placement with automatic equipment Flat upper surface and tape and reel packaging facilitate vacuum pick-up and placement. Standard reel packaging contains 5000 connectors. Temporary hold of FPC 2010.9 1 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH43B Series●0.2 mm Pitch, 0.9 mm above the board, Flexible Printed Circuit ZIF Connectors ■Specifications Current rating 0.2 A Operating temperature range -55 to +85°C (Note 1) Storage temperature range -10 to +50°C (Note 2) Voltage rating 30 Vrms AC Operating humidity range Relative humidity 90% max. (No condensation) Storage humidity range Relative humidity 90% max. (No condensation) Ratings Recommended FPC Thickness Item 0.2 ± 0.02 mm, Gold plated contact pads Specification Conditions 1. Insulation resistance 50 Mø min. 100 V DC 2. Withstanding voltage No flashover or insulation breakdown 90 Vrms AC / one minute 3. Contact resistance 100 mø max. * Including FPC conductor resistance 1 mA, AC max (AC: 1kHz) 4. Durability Contact resistance: 100 mø max. No damage, cracks, or parts dislocation 10 cycles 5. Vibration No electrical discontinuity of 1μs or longer Contact resistance: 100 mø max. No damage, cracks, or parts dislocation Frequency: 10 to 55 Hz, single amplitude of 0.75mm, 10 cycles in each of the 3 axis 6. Shock No electrical discontinuity of 1μs or longer Contact resistance: 100 mø max. No damage, cracks, or parts dislocation Acceleration of 981m/s , 6 ms duration, sine halfwave, 3 cycles in each of the 3 axis 7. Humidity (Steady state) Contact resistance: 100 mø max. Insulation resistance: 50 Mø min. No damage, cracks, or parts dislocation 96 hours at 40°C and humidity of 90 to 95% 8. Temperature cycle Contact resistance: 100 mø max. Insulation resistance: 50 Mø min. No damage, cracks, or parts dislocation Temperature : -55°C → +15°C to +35°C → +85°C→ +15°C to +35°C Time: 30 → 2 to 3 → 30 → 2 to 3 minutes 5 cycles 9. Resistance to soldering heat No deformation of components affecting performance Reflow: At the recommended temperature profile Manual soldering: 350°C ±10°C for 5 seconds 2 Note 1. Includes temperature rise caused by current flow. Note 2.The term "storage" refers to products stored for a long period prior to mounting and use. The operating temperature and humidity range covers the non-conducting condition of installed connectors in storage, shipment or during transportation after board mounting. Note 3. Information contained in this catalog represents general requirements for this Series. Contact us for the drawings and specifications for a specific part number shown. ■Materials Part Material Finish LCP Color:Beige PA Color:Black Insulator Contacts Phosphor bronze Metalfittings Remarks UL94V-0 Gold plated --------- Pure tin reflow plated --------- ■Ordering information FH 43B − 51S − 0.2 SHW (10) 1 2 3 1Series name : FH 2Series No.: 43B 3Number of positions : 21to81 4Contact pitch : 0.2mm 2 4 5 6 5Termination type : SHW…SMT horizontal staggered row mount type 6Plating specifications (10)…Gold plating with nickel barrier The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH43B Series●0.2 mm Pitch, 0.9 mm above the board, Flexible Printed Circuit ZIF Connectors ■Connector Dimensions A 0.2 B A * * (2.85) (0.95) (00.08) 0.4 Number of contacts (00.08) 0.4 C R (0.45) (0.12) (2.5) D E R 5°) 0.9 (1.75) (12 0.4 (0.53) (1.2) (1.6) 2.17 0.1 1 0.47 1 Note 1 2. 3. 4. 0.3 0.2 0.1 The coplanarity of each terminal lead within specified dimension is 0.1 mm Max. Packaged on tape and reel only. Check packaging specification. Slight variations in color of the plastic compounds do not affect form, fit or function of the connector. After reflow, the terminal plating may change color, however this does not represent a quality issue. Unit : mm CL No. Number of contacts A B C D E FH43B-21S-0.2SHW(10) Part Number ----- 21 5.8 3.6 4 4.53 5.29 FH43B-25S-0.2SHW(10) ----- 25 6.6 4.4 4.8 5.33 6.09 FH43B-31S-0.2SHW(10) ----- 31 7.8 5.6 6 6.53 7.29 FH43B-35S-0.2SHW(10) 0580-2803-5-10 35 8.6 6.4 6.8 7.33 8.09 FH43B-41S-0.2SHW(10) ----- 41 9.8 7.6 8 8.53 9.29 FH43B-45S-0.2SHW(10) ----- 45 10.6 8.4 8.8 9.33 10.09 FH43B-51S-0.2SHW(10) 0580-2806-3-10 51 11.8 9.6 10 10.53 11.29 FH43B-61S-0.2SHW(10) 0580-2805-0-10 61 13.8 11.6 12 12.53 13.29 FH43B-71S-0.2SHW(10) 0580-2807-6-10 71 15.8 13.6 14 14.53 15.29 FH43B-81S-0.2SHW(10) ----- 81 17.8 15.6 16 16.53 17.29 Note1. Tape and reel packaging (5,000 pieces/reel). Order by number of reels. 3 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH43B Series●0.2 mm Pitch, 0.9 mm above the board, Flexible Printed Circuit ZIF Connectors ×(n-1)/2 0.04 S 0.4 0.2±0.02 (0.18±0.01:Metal Mask) ×(n+1)/2 0.04 0.4±0.05 C S S (0.3±0.03:Metal Mask) 0.4 S 0.04 (0.58±0.03:Metal Mask) (0.2) 0.2±0.02 (0.18±0.01:Metal Mask) 0.2 (0.68±0.03:Metal Mask) 0.82±0.03 B 0.02±0.05 0.8±0.05 Recommended meal mask thickness : t=0.1 3.17±0.05 1.7±0.05 0.65±0.03 (0.55±0.03:Metal Mask) ■Recommended PCB mounting pattern and metal mask dimensions 0.485±0.05 ■Recommended FPC Dimensions A±0.1 (F) G±0.05 C±0.02 0.2 +0.03 − 0.02 0.4±0.02 0.2±0.02 M AX 0.25±0.05 R0 .2 AX M 0.05±0.15 0.74±0.1(Even pattern) 0.75±0.1(Odd pattern) 0.84±0.1(Even pattern) 0.85±0.1(Odd pattern) 1.45±0.1 0.25±0.05 .2 R0 0.055±0.02 0.67±0.05(Mating area) (2.8:Stiffeuer) 2 0.1 0. .2± X R A M (0.13:Odd pattern) (0.1:Even pattern) R0 1MIN 0.1 1.8MIN .2± R0 1.6±0.05 1.1±0.05 0.2±0.02 0.2 +0.03 − 0.02 0.67±0.05(Mating area) B±0.02 H±0.05(Mating area) ■Recommended FPC construction Part Number 4 Unit : mm CL No. Number of contacts B C F G H FH43B-21S-0.2SHW(10) ----- 21 3.6 4 5.3 4.5 4.94 FH43B-25S-0.2SHW(10) ----- 25 4.4 4.8 6.1 5.3 5.74 FH43B-31S-0.2SHW(10) ----- 31 5.6 6 7.3 6.5 6.94 FH43B-35S-0.2SHW(10) 0580-2803-5-10 35 6.4 6.8 8.1 7.3 7.74 FH43B-41S-0.2SHW(10) ----- 41 7.6 8 9.3 8.5 8.94 FH43B-45S-0.2SHW(10) ----- 45 8.4 8.8 10.1 9.3 9.74 FH43B-51S-0.2SHW(10) 0580-2806-3-10 51 9.6 10 11.3 10.5 10.94 FH43B-61S-0.2SHW(10) 0580-2805-0-10 61 11.6 12 13.3 12.5 12.94 FH43B-71S-0.2SHW(10) 0580-2807-6-10 71 13.6 14 15.3 14.5 14.94 FH43B-81S-0.2SHW(10) ----- 81 15.6 16 17.3 16.5 16.94 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH43B Series●0.2 mm Pitch, 0.9 mm above the board, Flexible Printed Circuit ZIF Connectors ■FHB Series FPC 1. Using Single-sided FPC Material Name Covering film layer Material Material Thickness (μm) Polyimide 1 mil thick. (25) Cover adhesive Surface treatment 2. Using Double-sided FPC (25) 0.2μm thick gold plated over 1 to 6μm nickel underplating 4 Copper foil Cu 1/3oz 12 Base adhesive Thermosetting adhesive 10 Base film Polyimide 1/2mil thick 15 Reinforcement material adhesive Thermosetting adhesive 30 Stiffener Polyimide 5 mil thick 125 Total 194 Material Name Covering film layer Material Material Thickness (μm) Polyimide 1 mil thick. Cover adhesive Surface treatment (25) (25) 0.2μm thick gold plated over 1 to 6μm nickel underplating 4 Through-hole copper Cu 12 Copper foil Cu 1/3oz 12 Base adhesive Thermosetting adhesive — Base film Polyimide 1/2mil thick 13 Base adhesive Thermosetting adhesive — Copper foil Cu 1/3oz (12) Cover adhesive Thermosetting adhesive 25 Covering film layer Polyimide 1/2 mil thick 13 Reinforcement material adhesive Thermosetting adhesive Stiffener Polyimide 4 mil thick 100 25 Total 204 * To prevent release of the FPC due to its bending, use of the double sided FPC with copper foil on the back side is NOT RECOMMENDED. 3. Precautions 1. This specification is a recommendation for the construction of the FH43B Series FPC and FFC (t=0.2 ±0.02). 2. For details about the construction, please contact the FPC/FFC manufacturers. 5 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH43B Series●0.2 mm Pitch, 0.9 mm above the board, Flexible Printed Circuit ZIF Connectors ■Packaging Specification 2±0.15 8±0.1 4±0.1 2±0.15 8±0.1 .5 Flat surface, for placement with automatic equipment. 1.5+0.1 0 1.7 +0.15 0 (M) (2.95) (3.85) J±0.3 L±0.1 Ø1 0 0 .1 (1.5) (0.3) .1 +00 (M) L±0.1 K±0.1 J±0.3 4±0.1 Ø1. 5+ 1.75±0.1 (1.5) (0.3) (0.95) Unreeling direction Unreeling direction (Ø1 3) ■Reel Dimensions 1.75±0.1 ●Embossed Carrier Tape Dimensions (Tape width to 32mm min.) ●Embossed Carrier Tape Dimensions (Tape width to 24mm max.) (Ø80) (Ø380) (L: INSIDE) (M: OUTSIDE) End portion Mounting portion Lead portion (400mm min.) Embossed carrier tape No connector inserted (25 pockets min.) No connector inserted (25 pockets min.) Top cover tape Unit : mm Part Number 6 CL No. Number of contacts J K L M N P FH43B-21S-0.2SHW(10) ----- 21 16 ----- 7.5 6 17.4 21.4 FH43B-25S-0.2SHW(10) ----- 25 16 ----- 7.5 6.8 17.4 21.4 FH43B-31S-0.2SHW(10) ----- 31 24 ----- 11.5 8 25.4 29.4 FH43B-35S-0.2SHW(10) 0580-2803-5-10 35 24 ----- 11.5 8.8 25.4 29.4 FH43B-41S-0.2SHW(10) ----- 41 24 ----- 11.5 10 25.4 29.4 FH43B-45S-0.2SHW(10) ----- 45 24 ----- 11.5 10.8 25.4 29.4 FH43B-51S-0.2SHW(10) 0580-2806-3-10 51 24 ----- 11.5 12 25.4 29.4 FH43B-61S-0.2SHW(10) 0580-2805-0-10 61 24 ----- 11.5 14 25.4 29.4 FH43B-71S-0.2SHW(10) 0580-2807-6-10 71 24 ----- 11.5 16 25.4 29.4 FH43B-81S-0.2SHW(10) ----- 81 32 28.4 14.2 18 33.4 37.4 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH43B Series●0.2 mm Pitch, 0.9 mm above the board, Flexible Printed Circuit ZIF Connectors ■Temperature Profile MAX 250°C 250 Temperature(°C) 230°C 200 HRS test condition Solder method : Reflow, IR/hot air Environment : Room air Solder composition :Paste, 96.5%Sn/3.0%Ag/0.5%Cu (Senju Metal Industry, Co., Ltd.'s Part 200°C 150 150°C 100 50 25°C 0 (60sec) 90~120sec Preheating (60sec) Soldering Number:M705-221CM5-32-10.5) Test board : Glass epoxy 100mm×72.5mm×0.8mm thick Land dimensions : 0.2mm×0.65mm, 0.2mm×0.82mm Metal mask : 0.18×0.55, 0.18×0.68×0.1mm thick The temperature profiles shown are based on the above conditions. In individual applications the actual temperature may vary, depending on solder paste type, volume / thickness and board size / thickness. Consult your solder paste and equipment manufacturer for specific recommendations. Start Time(Seconds) 7 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH43B Series●0.2 mm Pitch, 0.9 mm above the board, Flexible Printed Circuit ZIF Connectors ■Operation and Precautions Operation 1. FPC insertion procedure. Connector installed on the board. 1Lift up the actuator. Use thumb or index finger. 2Insert the FPC (contact surfaces facing down) at angle of approximately 10° to the board surface ①, making sure that the FPC positioning tabs clear the protrusions on both sides of the connector. Lower the FPC down ②, parallel to the board surface. FPC contact surface faces downward 12 5° ① ② 15° Protrusions for the FPC positioning. 3Rotate down the actuator until firmly closed. 2. FPC removal 1Lift up the actuator Pull up the FPC at an angle of approximately 10° ① and than withdrew it from the connector ②. 125 ° ② 15° ① Protrusions for the FPC positioning. 8 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH43B Series●0.2 mm Pitch, 0.9 mm above the board, Flexible Printed Circuit ZIF Connectors Precautions Exercise care when handling connectors. Follow recommendations given below. [ Precautions when mounting connectors on the PCB ] ◆Handling before mounting on PCB Insertion of the FPC or operation of the actuator prior to mounting on the PCB is NOT RECOMMENDED. ◆PC board warpage Minimize the warpage as much as possible. The connector is straight within 0.1 mm max. Make sure that the mounting area flatness can accept the connector terminals without causing any failure of the solder joints. ◆When braking the large PC board into individual boards exercise care NOT to damage the installed connectors. ◆When attaching the boards or other components with the screws make sure that any stresses will NOT cause board deflections affecting the mounting areas of the connector. 100 Connector F Board F Board 0.6 0.5MAX Connector 0.6 Fig. 1 0.5MAX ◆Bending of the board For a board width of 100 mm, bending of the board must be 0.5 mm max. (Ref to Fig. 1) 100 [ Precautions during FPC insertion and mating ] Pay attention to the following points when inserting FPC. ◆Actuator operation 1Do not apply excessive force when opening the actuator prior to FPC insertion. When opening make sure that the force is applied only to the actuator itself, avoiding touching of the contacts. Actuator Damage to the actuator Damage to the actuator 2Axis of rotation Assure free rotation of the actuator. 9 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH43B Series●0.2 mm Pitch, 0.9 mm above the board, Flexible Printed Circuit ZIF Connectors Precautions 3The actuator will rotate 125°C Do not apply force to rotate further. 12 5° 4When opening or closing the actuator, do so at the center section. 5Do not grasp or and lift the actuator (Fig. 3) nor insert the nail from the back of it (Fig. 4). Fig. 3 ◆FPC insertion Do not insert the FPC at any high angle from above. 15° Protrusions for FPC positioning 10 Fig. 4 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH43B Series●0.2 mm Pitch, 0.9 mm above the board, Flexible Printed Circuit ZIF Connectors Precautions As illustrated (Fig. 5) angle insertion may cause electrical discontinuity when the FPC is deflected in use. 45° Fig. 5 Opening of the FPC pattern To avert insertion of the FPC at an angle, consideration should be given to securing enough insertion space when designing the board lay-out. Insertion will be difficult when the FPC is too short. ● Contact FPC manufacturer for information about the bending specifications. ● Verification of the fully closed actuator ◆ The FPC should be fully inserted, with its positioning tabs fully behind the protrusions on both sides of the connector’s insertion slot (Fig. 6). FPC positioning tab Protrusions FPC positioning Fig. 6 [ Routing of the FPC (FPC fully inserted / actuator closed) ] ◆Do not apply any pull or upward-directed force to the FPC. Do not make any sharp bends of FPC close to the immediate exit from the connector (Fig. 7) Fig. 7 11 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH43B Series●0.2 mm Pitch, 0.9 mm above the board, Flexible Printed Circuit ZIF Connectors Precautions [ Removing of the FPC ] ◆Rotate the actuator to the fully open position (max. angle of 125°C) Lift the FPC approximately 10°C (making sure that the positioning tabs clear the protrusions on both sides) and carefully withdraw it from the connector. 125 ° 15° Protrusions for FPC positioning [ Other Precautions ] ◆Hand Soldering Precautions When hand soldering: 1Do not perform reflow or hand soldering with the FPC inserted in the connector. 2Do not apply excessive heat or touch the soldering iron anywhere other than the connector leads. 3Do not use excessive amount of solder or flux compounds. Operation of the actuator or contacts may be affected by excessive amounts of solder or flux compounds. ® 12 5-23,OSAKI 5-CHOME,SHINAGAWA-KU,TOKYO 141-8587,JAPAN PHONE: 81-3-3491-5300, FAX: 81-3-3495-5230 http://www.hirose.com http://www.hirose-connectors.com The contents of this catalog are current as of date of 09/2010. Contents are subject to change without notice for the purpose of improvements.