TH97/2478 FKBP200 - FKBP210 IATF 0060636 SGS TH07/1033 FAST RECOVERY BRIDGE RECTIFIERS PRV : 50 - 1000 Volts Io : 2.0 Amperes KBP 0.59 (14.9) 0.57 (14.5) FEATURES : * * * * * * * * TH09/2479 High case dielectric strength of 2000 VDC High surge current capability High reliability Low reverse current Low forward voltage drop Fast switching for high efficiency Ideal for printed circuit board Pb / RoHS Free Φ3 0.448 (11.4) 0.433 (11.0) + AC AC 0.0307 (0.78) 0.0303 (0.77) 0.696 (17.7) MIN. 0.150 (3.82) 0.148 (3.78) 0.151 (3.85 ) 0.147 (3.75) 0.051 (1.30) 0.043 (1.10) MECHANICAL DATA : * Case : Molded plastic * Epoxy : UL94V-0 rate flame retardant * Terminals : Plated lead solderable per MIL-STD-202, Method 208 guaranteed * Polarity : Polarity symbols marked on case * Mounting position : Any * Weight : 3.4 grams Dimensions in inches and ( millimeter ) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating at 25 °C ambient temperature unless otherwise specified . Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. RATING SYMBOL FKBP FKBP FKBP FKBP FKBP FKBP FKBP 200 201 202 204 206 208 210 UNIT Maximum Recurrent Peak Reverse Voltage VRRM 50 100 200 400 600 800 1000 V Maximum RMS Voltage VRMS 35 70 140 280 420 560 700 V Maximum DC Blocking Voltage VDC 50 100 200 400 600 800 1000 V Maximum Average Forward Current Tc = 50 °C IF(AV) 2.0 A IFSM 35 A Current Squared Time at t < 8.3 ms. 2 It 10 A2S Maximum Forward Voltage drop per Diode at I F = 1.0 A VF 1.3 V IR 10 μA IR(H) 500 μA Peak Forward Surge Current Single half sine wave Superimposed on rated load (JEDEC Method) Maximum DC Reverse Current Ta = 25 °C at Rated DC Blocking Voltage Ta = 100 °C Maximum Reverse Recovery Time (Note 1) Typical Thermal Resistance (Note 2) Operating Junction Temperature Range Storage Temperature Range Trr 150 250 500 ns RθJA 30 °C/W TJ - 50 to + 150 °C TSTG - 50 to + 150 °C Notes : 1 ) Measured with IF = 0.5 Amp., IR = 1 Amp., Irr = 0.25 Amp. 2 ) Thermal resistance from Junction to Ambient on P.C. Board with, 0.47" X 0.47" ( 12 mm. x 12 mm. ) Cu. pads. Page 1 of 2 Rev. 03 : June 11, 2009 TH97/2478 TH09/2479 IATF 0060636 SGS TH07/1033 RATING AND CHARACTERISTIC CURVES ( FKBP200 - FKBP210 ) FIG.1 - REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50 Ω Trr 10 Ω + 0.5 A + D.U.T. 0 PULSE GENERATOR ( NOTE 2 ) 50 Vdc (approx) 1Ω - 0.25 A OSCILLOSCOPE ( NOTE 1 ) - 1.0 A SET TIME BASE FOR 50/100 ns/cm NOTES : 1. Rise Time = 7 ns max., Input Impedance = 1 megaohm, 22 pF. 1 cm 2. Rise time = 10 ns max., Source Impedance = 50 ohms. 3. All Resistors = Non-inductive Types. FIG.3 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 50 2.5 PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD OUTPUT CURRENT, AMPERES FIG.2 - DERATING CURVE FOR OUTPUT RECTIFIED CURRENT 2.0 1.5 1.0 0.5 Tc = 50 °C 40 30 20 10 60Hz RESISTIVE OR INDUCTIVE LOAD 0 0 25 50 75 100 125 150 0 175 1 CASE TEMPERATURE, ( °C) 2 6 10 20 40 60 100 NUMBER OF CYCLES AT 60Hz FIG.4 - TYPICAL FORWARD CHARACTERISTICS FIG.5 - TYPICAL REVERSE CHARACTERISTICS PER DIODE PER DIODE 100 10 Pulse Width = 300 μs 2% Duty Cycle TJ = 100 °C REVERSE CURRENT, MICROAMPERES FORWARD CURRENT, AMPERES 4 TJ = 25 °C 10 1.0 1.0 0.1 TJ = 25 °C 0.01 0.1 0 20 40 60 80 100 120 140 PERCENT OF RATED REVERSE VOLTAGE, (%) 0.01 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 FORWARD VOLTAGE, VOLTS Page 2 of 2 Rev. 03 : June 11, 2009