HA-5104/883 Low Noise, High Performance, Quad Operational Amplifier July 1994 Features Description • This Circuit is Processed in Accordance to MIL-STD883 and is Fully Conformant Under the Provisions of Paragraph 1.2.1. Low noise and high performance are key words describing the unity gain stable HA-5104/883. This general purpose quad amplifier offers an array of dynamic specifications including 1V/µs slew rate (min), and 8MHz bandwidth (typ). Complementing these outstanding parameters are very low noise specifications of 4.3nV/√Hz at 1kHz (typ) or 6nV/√Hz (max). • Low Input Noise Voltage Density at 1kHz. . 6nV/√Hz (Max) 4.3nV/√Hz (Typ) • Slew Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . 1V/µs (Min) 3V/µs (Typ) • Unity Gain Bandwidth . . . . . . . . . . . . . . . . . 8MHz (Typ) • High Open Loop Gain (Full Temp) . . . . . 100kV/V (Min) 250kV/V (Typ) • High CMRR, PSRR (Full Temp) . . . . . . . . . . . 86dB (Min) 100dB (Typ) • Low Offset Voltage Drift . . . . . . . . . . . . . . 3µV/oC (Typ) Fabricated using the Intersil standard high frequency D.I. process, these operational amplifiers also offer excellent input specifications such as 2.5mV (max) offset voltage and 75nA (max) offset current. Complementing these specifications are 100dB (min) open loop gain and 55dB channel separation (min). Economically, the HA-5104/883 also consumes a very moderate amount of power (225mW per package) while also saving board space and cost. This impressive combination of features make this amplifier ideally suited for designs ranging from audio amplifiers and active filters to the most demanding signal conditioning and instrumentation circuits. • No Crossover Distortion • Standard Quad Pinout Applications Ordering Information • High Q Active Filters • Audio Amplifiers PART NUMBER • Integrators • Signal Generators • Instrumentation Amplifiers TEMPERATURE RANGE PACKAGE HA1-5104/883 -55oC to +125oC 14 Lead CerDIP HA4-5104/883 -55oC to +125oC 20 Lead Ceramic LCC Pinouts 3 2 1 V+ 4 11 V- +IN2 5 10 +IN3 -IN2 6 OUT 2 7 +2 - +IN1 12 +IN4 3 +- 9 -IN3 8 OUT 3 3-114 18 +IN4 4 NC 5 V+ 6 NC 7 +IN2 8 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. http://www.intersil.com or 407-727-9207 | Copyright © Intersil Corporation 1999 20 19 + 1 - + 4 17 NC 16 V- 3 - + 2 + - 15 NC 14 +IN3 9 10 11 12 13 -IN3 3 4+ OUT 3 +IN1 -1 + NC 2 OUT 2 -IN1 -IN2 1 -IN4 NC 13 -IN4 OUT 1 OUT 4 14 OUT 4 OUT 1 HA-5104/883 (CLCC) TOP VIEW -IN1 HA-5104/883 (CERDIP) TOP VIEW 511014-883 File Number 3710 Spec Number Specifications HA5104/883 Absolute Maximum Ratings Thermal Information Voltage Between V+ and V- Terminals . . . . . . . . . . . . . . . . . . . . 40V Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7V Voltage at Either Input Terminal . . . . . . . . . . . . . . . . . . . . . . V+ to VPeak Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Indefinite (One Amplifier Shorted to Ground) Junction Temperature (TJ) . . . . . . . . . . . . . . . . . . . . . . . . . . +175oC Storage Temperature Range . . . . . . . . . . . . . . . . . -65oC to +150oC ESD Rating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <2000V Lead Temperature (Soldering 10s) . . . . . . . . . . . . . . . . . . . . +300oC Thermal Resistance θJA θJC CerDIP Package . . . . . . . . . . . . . . . . . . . 75oC/W 20oC/W Ceramic LCC Package . . . . . . . . . . . . . . 65oC/W 15oC/W Package Power Dissipation Limit at +75oC for TJ ≤ +175oC CerDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.33W Ceramic LCC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.54W Package Power Dissipation Derating Factor Above +75oC CerDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.3mW/oC Ceramic LCC Package . . . . . . . . . . . . . . . . . . . . . . . . 15.4mW/oC CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Operating Conditions Operating Temperature Range . . . . . . . . . . . . . . . . -55oC to +125oC Operating Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . ±5V to ±15V VINCM ≤ 1/2 (V+ - V-) RL ≥ 2kΩ TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS Device Tested at: VSUPPLY = ±15V, RSOURCE = 100Ω, RLOAD = 500kΩ, VOUT = 0V, Unless Otherwise Specified. PARAMETERS Input Offset Voltage SYMBOL VIO CONDITIONS TEMPERATURE MIN MAX UNITS 1 +25oC -2.5 2.5 mV -3.0 3.0 mV -200 200 nA -325 325 nA -200 200 nA -325 325 nA -75 75 nA -125 125 nA +12 - V +12 - V - -12 V - -12 V 100 - kV/V 100 - kV/V 100 - kV/V 100 - kV/V 86 - dB 86 - dB 86 - dB 86 - dB VCM = 0V 2, 3 Input Bias Current +IB -IB Input Offset Current Common Mode Range IIO +CMR VCM = 0V, +RS = 10kΩ, -RS = 100Ω 1 2, 3 VCM = 0V, +RS = 100Ω, -RS = 10kΩ 1 2, 3 VCM = 0V, +RS = 10kΩ, -RS = 10kΩ 1 2, 3 V+ = +3V, V- = -27V 1 2, 3 -CMR V+ = +27V, V- = -3V 1 2, 3 Large Signal Voltage Gain +AVOL -AVOL Common Mode Rejection Ratio +CMRR -CMRR LIMITS GROUP A SUBGROUPS VOUT = 0V and +10V, RL = 2kΩ 4 5, 6 VOUT = 0V and -10V, RL = 2kΩ 4 5, 6 ∆VCM = +5V, V+ = +10V, V- = -20V, VOUT = -5V 1 2, 3 ∆VCM = -5V, V+ = +20V, V- = -10V, VOUT = +5V 1 2, 3 +125oC, -55oC +25oC +125oC, -55oC +25oC +125oC, -55oC +25oC +125oC, -55oC +25oC +125oC, -55oC +25oC +125oC, -55oC +25oC +125oC, -55oC +25oC +125oC, -55oC +25oC +125oC, -55oC +25oC +125oC, -55oC Spec Number 3-115 511014-883 Specifications HA5104/883 TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS (Continued) Device Tested at: VSUPPLY = ±15V, RSOURCE = 100Ω, RLOAD = 500kΩ, VOUT = 0V, Unless Otherwise Specified. PARAMETERS Output Voltage Swing SYMBOL +VOUT1 -VOUT1 +VOUT2 -VOUT2 Output Current +IOUT -IOUT Quiescent Power Supply Current +ICC -ICC Power Supply Rejection Ratio +PSRR -PSRR CONDITIONS LIMITS GROUP A SUBGROUPS TEMPERATURE MIN MAX UNITS 1 +25oC 10 - V 2, 3 +125oC, -55oC 10 - V 1 +25oC - -10 V 2, 3 +125oC, -55oC - -10 V 1 +25oC 12 - V 2, 3 +125oC, -55oC 12 - V 1 +25oC - -12 V 2, 3 +125oC, -55oC - -12 V 1 +25oC 10 - mA 2, 3 +125oC, -55oC 10 - mA 1 +25oC - -10 mA 2, 3 +125oC, -55oC - -10 mA 1 +25oC - 6.5 mA 2, 3 +125oC, -55oC - 7.5 mA 1 +25oC -6.5 - mA 2, 3 +125oC, -55oC -7.5 - mA 1 +25oC 86 - dB 2, 3 +125oC, -55oC 86 - dB 1 +25oC 86 - dB 2, 3 +125oC, -55oC 86 - dB RL = 2kΩ RL = 2kΩ RL = 10kΩ RL = 10kΩ VOUT = -5V VOUT = +5V VOUT = 0V, IOUT = 0mA VOUT = 0V, IOUT = 0mA ∆VSUP = 10V, V+ = +10V, V- = -15V V+ = +20V, V- = -15V ∆VSUP = 10V, V+ = +15V, V- = -10V V+ = +15V, V- = -20V TABLE 2. AC ELECTRICAL PERFORMANCE CHARACTERISTICS Device Tested at: VSUPPLY = ±15V, RSOURCE = 50Ω, RLOAD = 2kΩ, CLOAD = 50pF, AVCL = +1V/V, Unless Otherwise Specified. PARAMETERS Slew Rate SYMBOL +SR -SR Rise and Fall Time Overshoot CONDITIONS LIMITS GROUP A SUBGROUPS TEMPERATURE MIN MAX UNITS 4 +25oC 1 - V/µs 4 +25oC 1 - V/µs - 200 ns VOUT = -3V to +3V VOUT = +3V to -3V TR VOUT = 0 to +200mV 10% ≤ TR ≤ 90% 4 +25oC TF VOUT = 0 to -200mV 10% ≤ TF ≤ 90% 4 +25oC - 200 ns +OS VOUT = 0 to +200mV 4 +25oC - 35 % 4 +25oC - 35 % -OS VOUT = 0 to -200mV Spec Number 3-116 511014-883 Specifications HA5104/883 TABLE 3. ELECTRICAL PERFORMANCE CHARACTERISTICS Device Characterized at: VSUPPLY = ±15V, RLOAD = 2kΩ, CLOAD = 50pF, AVCL = 1V/V, Unless Otherwise Specified. LIMITS PARAMETERS SYMBOL CONDITIONS NOTES TEMPERATURE MIN MAX UNITS Differential Input Resistance RIN VCM = 0V 1 +25oC 250 - kΩ Input Noise Voltage Density EN RS = 20Ω, fO = 1000Hz 1 +25oC - 6 nV/√Hz Input Noise Current Density IN RS = 2MΩ, fO = 1000Hz 1 +25oC - 3 pA/√Hz Full Power Bandwidth FPBW VPEAK = 10V 1, 2 +25oC 32 - kHz Minimum Closed Loop Stable Gain CLSG RL = 2kΩ, CL = 50pF 1 -55oC to +125oC +1 - V/V Output Resistance ROUT Open Loop 1 +25oC - 270 Ω - 225 mW 55 - dB Quiescent Power Consumption PC VOUT = 0V, IOUT = 0mA Channel Separation CS RS = 1kΩ, AVCL = 100V/V, VIN = 100mVPEAK at 10kHz Referred to Input 1, 3 1 -55oC to +125oC +25oC NOTES: 1. Parameters listed in Table 3 are controlled via design or process parameters and are not directly tested at final production. These parameters are lab characterized upon initial design release, or upon design changes. These parameters are guaranteed by characterization based upon data from multiple production runs which reflect lot to lot and within lot variation. 2. Full Power Bandwidth guarantee based on Slew Rate measurement using FPBW = Slew Rate/(2πVPEAK). 3. Quiescent Power Consumption based upon Quiescent Supply Current test maximum. (No load on outputs.). TABLE 4. ELECTRICAL TEST REQUIREMENTS MIL-STD-883 TEST REQUIREMENTS SUBGROUPS (SEE TABLES 1 AND 2) Interim Electrical Parameters (Pre Burn-In) 1 Final Electrical Test Parameters 1 (Note 1), 2, 3, 4, 5, 6 Group A Test Requirements 1, 2, 3, 4, 5, 6 Groups C and D Endpoints 1 NOTE: 1. PDA applies to Subgroup 1 only. Spec Number 3-117 511014-883 HA5104/883 Die Characteristics DIE DIMENSIONS: 95 x 99 x 19 mils ± 1 mils 2420 x 2530 x 483µm ± 25.4µm METALLIZATION: Type: Al, 1% Cu Thickness: 16kÅ ± 2kÅ GLASSIVATION: Type: Nitride (Si3N4) over Silox (SIO2, 5% Phos.) Silox Thickness: 12kÅ ± 2kÅ Nitride Thickness: 3.5kÅ ± 1.5kÅ WORST CASE CURRENT DENSITY: 1.43 x 105 A/cm2 SUBSTRATE POTENTIAL (Powered Up): Unbiased TRANSISTOR COUNT: 175 PROCESS: Bipolar Dielectric Isolation Metallization Mask Layout HA5104/883 +IN2 V+ +IN1 -IN1 -IN2 OUT2 OUT1 OUT3 OUT4 -IN3 -IN4 +IN3 V- +IN4 All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification. Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see web site http://www.intersil.com Spec Number 3-118 511014-883