User’s Manual IE-703217-G1-EM1 Emulation Board Target Devices V850ES/KF1TM V850ES/KG1TM V850ES/KJ1TM Document No. U16594EJ1V0UM00 (1st edition) Date Published September 2003 N CP(K) 2003 Printed in Japan [MEMO] 2 User’s Manual U16594EJ1V0UM V850ES/KF1, V850ES/KG1, and V850ES/KJ1 are trademarks of NEC Electronics Corporation. Windows is either a trademark or a registered trademark of Microsoft Corporation in the United States and/or other countries. PC/AT is a trademark of International Business Machines Corporation. • The information in this document is current as of February, 2003. The information is subject to change without notice. For actual design-in, refer to the latest publications of NEC Electronics data sheets or data books, etc., for the most up-to-date specifications of NEC Electronics products. Not all products and/or types are available in every country. Please check with an NEC Electronics sales representative for availability and additional information. • No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Electronics. NEC Electronics assumes no responsibility for any errors that may appear in this document. • NEC Electronics does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from the use of NEC Electronics products listed in this document or any other liability arising from the use of such products. No license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC Electronics or others. • Descriptions of circuits, software and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples. The incorporation of these circuits, software and information in the design of a customer's equipment shall be done under the full responsibility of the customer. NEC Electronics assumes no responsibility for any losses incurred by customers or third parties arising from the use of these circuits, software and information. • While NEC Electronics endeavors to enhance the quality, reliability and safety of NEC Electronics products, customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To minimize risks of damage to property or injury (including death) to persons arising from defects in NEC Electronics products, customers must incorporate sufficient safety measures in their design, such as redundancy, fire-containment and anti-failure features. • NEC Electronics products are classified into the following three quality grades: "Standard", "Special" and "Specific". The "Specific" quality grade applies only to NEC Electronics products developed based on a customerdesignated "quality assurance program" for a specific application. The recommended applications of an NEC Electronics product depend on its quality grade, as indicated below. Customers must check the quality grade of each NEC Electronics product before using it in a particular application. "Standard": Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots. "Special": Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support). "Specific": Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems and medical equipment for life support, etc. The quality grade of NEC Electronics products is "Standard" unless otherwise expressly specified in NEC Electronics data sheets or data books, etc. If customers wish to use NEC Electronics products in applications not intended by NEC Electronics, they must contact an NEC Electronics sales representative in advance to determine NEC Electronics' willingness to support a given application. (Note) (1) "NEC Electronics" as used in this statement means NEC Electronics Corporation and also includes its majority-owned subsidiaries. (2) "NEC Electronics products" means any product developed or manufactured by or for NEC Electronics (as defined above). M8E 02. 11-1 User’s Manual U16594EJ1V0UM 3 Regional Information Some information contained in this document may vary from country to country. Before using any NEC Electronics product in your application, pIease contact the NEC Electronics office in your country to obtain a list of authorized representatives and distributors. They will verify: • Device availability • Ordering information • Product release schedule • Availability of related technical literature • Development environment specifications (for example, specifications for third-party tools and components, host computers, power plugs, AC supply voltages, and so forth) • Network requirements In addition, trademarks, registered trademarks, export restrictions, and other legal issues may also vary from country to country. [GLOBAL SUPPORT] http://www.necel.com/en/support/support.html NEC Electronics America, Inc. (U.S.) NEC Electronics (Europe) GmbH NEC Electronics Hong Kong Ltd. Santa Clara, California Tel: 408-588-6000 800-366-9782 Duesseldorf, Germany Tel: 0211-65 03 01 Hong Kong Tel: 2886-9318 • Sucursal en España Madrid, Spain Tel: 091-504 27 87 • Succursale Française Vélizy-Villacoublay, France Tel: 01-30-67 58 00 • Filiale Italiana Milano, Italy Tel: 02-66 75 41 • Branch The Netherlands Eindhoven, The Netherlands Tel: 040-244 58 45 • Tyskland Filial Taeby, Sweden Tel: 08-63 80 820 NEC Electronics Hong Kong Ltd. Seoul Branch Seoul, Korea Tel: 02-558-3737 NEC Electronics Shanghai, Ltd. Shanghai, P.R. China Tel: 021-6841-1138 NEC Electronics Taiwan Ltd. Taipei, Taiwan Tel: 02-2719-2377 NEC Electronics Singapore Pte. Ltd. Novena Square, Singapore Tel: 6253-8311 • United Kingdom Branch Milton Keynes, UK Tel: 01908-691-133 J03.4 4 User’s Manual U16594EJ1V0UM INTRODUCTION Target Readers This manual is intended for users who design and develop application systems using the V850ES/KF1, V850ES/KG1, and V850ES/KJ1 microcontrollers. Purpose The purpose of this manual is to describe the basic specifications of the IE703217-G1-EM1 and its proper operation. Organization This manual is broadly divided into the following parts. How to Read This Manual • Outline • Setup procedure • Part names and functions • Cautions • Switch settings • Restrictions It is assumed that the reader of this manual has general knowledge in the fields of electrical engineering, logic circuits, and microcontrollers. Use the IE-703217-G1-EM1 connected to the in-circuit emulator (IE-V850ES-G1). This manual describes the basic setup procedures and switch settings of the IE-703217-G1-EM1 and IE-V850ES-G1. For the part names, functions, and configuration parts of the IE-V850ES-G1, refer to the IE-V850ES-G1 User’s Manual (U16313E) provided separately. To learn about the basic specifications and operation →Read this manual in the order listed in CONTENTS. To learn software settings such as the operation methods, command functions, etc., of the IE-V850ES-G1 or IE-703217-G1-EM1 →Read the user’s manual of the debugger (sold separately) that is used. Conventions Note: Footnote for item marked with Note in the text Caution: Information requiring particular attention Remark: Supplementary information Binary … ×××× or ××××B Numeral representation: Decimal ... ×××× Hexadecimal ... ××××H Prefix representing a power of 2 (address space, memory capacity): K (kilo): 10 2 = 1024 20 M (mega): 2 = 1024 Terminology 2 The meanings of terms used in this manual are listed below. Target device This is the device to be emulated. Target system The system (user-built system) to be debugged. configured by the user. Emulation CPU The CPU that executes the program created by the user in the emulator. This includes the target program and hardware User’s Manual U16594EJ1V0UM 5 Related Documents When using this manual, refer to the following manuals. The related documents (user’s manuals) indicated in this publication may include preliminary versions. However, preliminary versions are not marked as such. Documents Related to Development Tools (User’s Manuals) Document Name Document Number IE-V850ES-G1 (In-Circuit Emulator for V850ES) U16313E IE-703217-G1-EM1 (In-Circuit Emulator Emulation Board for V850ES/KF1, V850ES/KG1, V850ES/KJ1) This manual V850ES/KF1, V850ES/KG1, V850ES/KJ1 Hardware U15862E CA850 Ver.2.50 C Compiler Package Operation U16053E C Language U16054E PM Plus U16055E Assembly Language TM U16042E ID850 Ver.2.50 Integrated Debugger Operation Windows based U16217E SM850 Ver.2.50 System Simulator Operation Windows based U16218E SM850 Ver.2.00 or Later System Simulator External Part User Open Interface Specifications U14873E RX850 Ver.3.13 or Later (Real-Time OS) Basics U13430E Installation U13410E Technical U13431E RX850 Pro Ver.3.13 (Real-Time OS) Basics U13773E Installation U13774E Technical U13772E RD850 Ver.3.01 Task Debugger U13737E RD850 Pro Ver.3.01 Task Debugger U13916E AZ850 Ver.3.10 System Performance Analyzer U14410E PG-FP4 Flash Memory Programmer U15260E Caution The related documents listed above are subject to change without notice. Be sure to use the latest version of each document when designing. 6 User’s Manual U16594EJ1V0UM CONTENTS CHAPTER 1 OUTLINE ........................................................................................................................10 1.1 Product Configuration ...........................................................................................................11 1.2 Features ..................................................................................................................................12 1.3 Function Specifications (When Connected to IE-V850ES-G1) ..........................................13 1.4 System Configuration............................................................................................................14 1.5 Contents in Carton.................................................................................................................15 CHAPTER 2 PART NAMES AND FUNCTIONS..................................................................................16 2.1 Part Names and Functions of IE-703217-G1-EM1 ...............................................................16 2.2 LEDs Controlled by IE-703217-G1-EM1................................................................................18 CHAPTER 3 SWITCH SETTINGS .......................................................................................................19 3.1 Clock Settings ........................................................................................................................19 3.2 Pull-Up Resistor Settings ......................................................................................................20 3.3 Power-ON Threshold Voltage Settings ................................................................................21 3.4 Regulator Output Stabilization Capacitance Setting Jumpers..........................................22 CHAPTER 4 SETUP PROCEDURE ....................................................................................................23 4.1 Removing Probe and Replacing Clock Module ..................................................................23 4.2 Removing Emulation Board ..................................................................................................25 4.3 Probe Cable Connection .......................................................................................................28 CHAPTER 5 CAUTIONS .....................................................................................................................29 CHAPTER 6 RESTRICTIONS .............................................................................................................30 APPENDIX A TARGET INTERFACE CHARACTERISTICS...............................................................31 APPENDIX B EXTERNAL VIEWS.......................................................................................................44 User’s Manual U16594EJ1V0UM 7 LIST OF FIGURES Figure No. Title Page 1-1 System Configuration ........................................................................................................................................14 1-2 Contents in Carton.............................................................................................................................................15 2-1 Part Names of IE-703217-G1-EM1....................................................................................................................16 2-2 LEDs Controlled by IE-703217-G1-EM1............................................................................................................18 3-1 JP4 Settings at Shipment ..................................................................................................................................21 3-2 Changing Power-ON Threshold Voltage............................................................................................................21 4-1 Opening/Closing Cover Step 1 (Removing Front Cover 1)................................................................................23 4-2 Opening/Closing Cover Step 1 (After Removing Front Cover 1) .......................................................................24 4-3 Opening/Closing Cover Step 2 (Loosening Screws) .........................................................................................25 4-4 Opening/Closing Cover Step 2 (Lifting Front Cover 2) ......................................................................................26 4-5 Opening/Closing Cover Step 2 (After Lifting Front Cover 2)..............................................................................27 4-6 Probe Cable Attachment Position......................................................................................................................28 A-1 Equivalent Circuit A ...........................................................................................................................................31 A-2 Equivalent Circuit B ...........................................................................................................................................31 A-3 Equivalent Circuit C ...........................................................................................................................................31 A-4 Equivalent Circuit D ...........................................................................................................................................32 A-5 Equivalent Circuit E ...........................................................................................................................................32 A-6 Equivalent Circuit F............................................................................................................................................32 A-7 Equivalent Circuit G ...........................................................................................................................................33 A-8 Equivalent Circuit H ...........................................................................................................................................33 A-9 Equivalent Circuit I.............................................................................................................................................34 A-10 Equivalent Circuit J ............................................................................................................................................34 8 User’s Manual U16594EJ1V0UM LIST OF TABLES Figure No. Title Page 3-1 Main Clock Settings...........................................................................................................................................19 3-2 Pull-Up Resistor Settings...................................................................................................................................20 3-3 Regulator Output Stabilization Capacitance Settings........................................................................................22 A-1 Pin Correspondence List (V850ES/KJ1 Pin Names) .........................................................................................35 A-2 Pin Correspondence List (V850ES/KG1 Pin Names) ........................................................................................39 A-3 Pin Correspondence List (V850ES/KF1 Pin Names).........................................................................................42 User’s Manual U16594EJ1V0UM 9 CHAPTER 1 OUTLINE The IE-703217-G1-EM1 is an emulation board for the IE-V850ES-G1 in-circuit emulator. Connected to the IE-V850ES-G1, the IE-703217-G1-EM1 can be used for efficient hardware and software debugging during system development using the V850ES/KF1, V850ES/KG1, and V850ES/KJ1. This manual describes the basic setup procedure and the switch settings of the IE-V850ES-G1 when connected to the IE-703217-G1-EM1. For the part names and functions of the IE-V850ES-G1, refer to the separate IE-V850ES-G1 User’s Manual (U16313E). 10 User’s Manual U16594EJ1V0UM CHAPTER 1 OUTLINE 1.1 Product Configuration Separately-sold products In-circuit emulator (IE-V850ES-G1) Emulation board (IE-703217-G1-EM1) The IE-V850ES-G1 can be used as an in-circuit emulator for the V850ES/KF1, V850ES/KG1, and V850ES/KJ1 by installing the IE-703217-G1-EM1 board. Separately-sold products Sockets EV-703210GC EV-703210GK EV-703214GC EV-703217GJ PC interface board IE-70000-PCI-IF(-A) IE-70000-CD-IF-A Package conversion sockets made by NEC Electronics EV-703210GC: For V850ES/KF1 (GC package) EV-703210GK: For V850ES/KF1 (GK package) EV-703214GC: For V850ES/KG1 EV-703217GJ: For V850ES/KJ1 This is a board for connecting the IE-V850ES-G1 to a PC. , More than one such board can be installed using the PC s expansion slots. IE-70000-PCI-IF(-A): For PCI bus IE-70000-CD-IF-A: For PCMCIA socket User’s Manual U16594EJ1V0UM 11 CHAPTER 1 OUTLINE 1.2 Features • Maximum operating frequency: 20 MHz (2.7 V to 5.5 V) • The following pins can be masked. NMI, WAIT, RESET, HLDRQ • The external dimensions of the IE-703217-G1-EM1 are listed below Item External dimensions 12 Value Height 35 mm Width 205 mm Depth 140 mm User’s Manual U16594EJ1V0UM CHAPTER 1 OUTLINE 1.3 Function Specifications (When Connected to IE-V850ES-G1) Item Specification Emulation memory capacity Internal ROM 1 MB For user memory 4 MB Internal ROM 256 KB External memory 1 MB Memory access detection coverage memory capacity External memory 1 MB Branch destination entry count calculation coverage memory capacity Internal ROM 256 KB External memory 1 MB Execution/pass detection coverage memory capacity Trace memory capacity 168 bits × 32 K frames Time measurement function Internal timers × 3 External logic probe 8-bit external trace possible Trace/break event setting possible Break function Event break Step execution break Forced break Fail-safe break • Illegal access to peripheral I/O • Access to guard area • Write to ROM area Caution Some functions may not be supported depending on the debugger that is used. User’s Manual U16594EJ1V0UM 13 CHAPTER 1 OUTLINE 1.4 System Configuration The system configuration when using the IE-703217-G1-EM1 connected to the IE-V850ES-G1, which itself is connected to a PC (PC-9800 series or PC/AT TM compatible) is shown below. Figure 1-1. System Configuration <10> <7> Target connector connection example (enlarged view) <6> <1> <8> <9> Target system <2> <8> <4> <3> <5> <9> Target system Remarks <1>: PC (PC-9800 series or PC/AT compatible) <2>: Debugger (sold separately), device file (obtained separately)Note 1 <3>: PC interface board (IE-70000-PCI-IF(-A), IE-70000-CD-IF-A: Sold separately) <4>: PC interface cable (supplied with IE-V850ES-G1) <5>: IE-V850ES-G1 (sold separately) <6>: In-circuit emulator emulation board (this product) <7>: Probe cableNote 2 (supplied with this product) <8>: Conversion adapterNote 2 <9>: Target connectorNote 2 <10>: Power-supply cable (3 types) (supplied with IE-V850ES-G1) Notes 1. The device file can be downloaded from the NEC Electronics website. (URL: http://www.necel.com/micro) 2. For the probe cable, conversion adapter, and target connector, refer to the user's manual of the emulation board. 14 User’s Manual U16594EJ1V0UM CHAPTER 1 OUTLINE 1.5 Contents in Carton The IE-703217-G1-EM1 package contains the IE-703217-G1-EM1 emulation board, a guarantee card, a packing list, this manual, and an accessory bag. Check whether the accessory bag contains the items listed below. If you find any missing or damaged items, contact an NEC Electronics sales representative or distributor. Figure 1-2. Contents in Carton <1> IE-703217-G1-EM1 <4> Packing list <3> Guarantee card <2> Accessory bag <1> IE-703217-G1-EM1 × 1 <2> Accessory bag × 1 <3> Guarantee card × 1 <4> Packing list × 1 Check whether the accessory bag contains the following items in addition to this manual and the packing list (× 1). (a) 8-pin header (for resonator replacement): ×1 (b) 4-pin header (for reference voltage replacement): × 1 (c) Socket (for REGC capacitor replacement): ×1 (d) Screws/washers: 6 sets (6 screws + 6 washers) User’s Manual U16594EJ1V0UM 15 CHAPTER 2 PART NAMES AND FUNCTIONS This chapter describes the part names and functions of the IE-703217-G1-EM1. For the part names and functions of the IE-V850ES-G1, refer to the IE-V850ES-G1 User’s Manual (U16313E). 2.1 Part Names and Functions of IE-703217-G1-EM1 Figure 2-1. Part Names of IE-703217-G1-EM1 Regulator output stabilization capacitance setting jumper JP7 Regulator output stabilization capacitance socket JP8 JP7JP8 3 2 SW1 8 1 1 Power-ON threshold voltage setting socket JP4 Pull-up resistance setting switch SW1 4 JP4 1 1 Main clock oscillator socket X1 X1 1 1 OSC2 7 CN7 CN6 CN5 1 OSC1 8 1 1 1 50 50 Subclock resonator socket OSC2 Main clock resonator socket OSC1 Emulation probe cable connection connectors CN5,CN6,CN7 50 GXP-AXK/KEL IE-703217-G1-EM1 16 User’s Manual U16594EJ1V0UM CHAPTER 2 PART NAMES AND FUNCTIONS (1) Emulation probe cable connection connectors (CN5, CN6, CN7) Connect the supplied probe cable. (2) Main clock resonator socket (OSC1) This socket is used to connect the main clock resonator. (For details, refer to 3.1 Clock Settings.) (3) Subclock resonator socket (OSC2) This socket is used to connect the subclock resonator. (For details, refer to 3.1 Clock Settings.) (4) Main clock oscillator socket (X1) This socket is used to connect the main clock oscillator. (For details, refer to 3.1 Clock Settings.) (5) Pull-up resistance setting switch (SW1) This switch is used to set emulation of the pull-up resistance, which is a mask option of the V850ES/KF1, V850ES/KG1, and V850ES/KJ1. (For details, refer to 3.2 Pull-Up Resistor Settings.) (6) Power-ON threshold voltage setting socket (JP4) This socket is used to set the threshold voltage for judging whether the target system is connected. (For details, refer to 3.3 Power-ON Threshold Voltage Settings.) (7) Regulator output stabilization capacitance socket (JP8) This socket is used to stabilize the output when using the regulator of the V850ES/KF1, V850ES/KG1, or V850ES/KJ1. (For details, refer to 3.4 Regulator Output Stabilization Capacitance Setting Jumpers.) (8) Regulator output stabilization capacitance setting jumper (JP7) This jumper is used to set whether to use the regulator of the V850ES/KF1, V850ES/KG1, or V850ES/KJ1. (For details, refer to 3.4 Regulator Output Stabilization Capacitance Setting Jumpers.) User’s Manual U16594EJ1V0UM 17 CHAPTER 2 PART NAMES AND FUNCTIONS 2.2 LEDs Controlled by IE-703217-G1-EM1 Some of the LEDs mounted in the IE-V850ES-G1 are controlled by the IE-703217-G1-EM1. For the LEDs that are controlled by the IE-V850ES-G1, refer to the IE-V850ES-G1 User’s Manual (U16313E). Figure 2-2. LEDs Controlled by IE-703217-G1-EM1 (1) Target RESET LED (2) Target BVDD LED (3) Target EVDD LED LEDs controlled by IE-V850ES-G1 STATUS LED (1) Target RESET LED The status of the RESET signal connected to the target system is indicated as follows. Lit (ON): The target system is connected and the RESET signal is active (GND level). Unlit (OFF): Either the target system is not connected, or the RESET signal is inactive (VDD level). (2) Target BVDD LED The status of the BVDD signal connected to the target system is indicated as follows. Lit (ON): The target system is connected, and voltage is being applied to the BVDD pin. Unlit (OFF): Either the target system is not connected, or voltage is not being applied to the BVDD pin. (3) Target EVDD LED The status of the EVDD signal connected to the target system is indicated as follows. Lit (ON): The target system is connected and voltage is being applied to the EVDD pin. Unlit (OFF): Either the target system is not connected, or voltage is not being applied to the EVDD pin. 18 User’s Manual U16594EJ1V0UM CHAPTER 3 SWITCH SETTINGS This chapter describes the settings of the switches of the IE-703217-G1-EM1. 3.1 Clock Settings Table 3-1 lists the main clock settings. For the locations of OSC1 and X1, refer to Figure 2-1. Since only the 32.768 kHz resonator on the IE-703217-G1-EM1 is connectable for the subclock, the oscillator cannot be changed. Table 3-1. Main Clock Settings Main Clock Supply Source Resonator OSC1 X1 Capacitance Resonator Debugger Setting − (don’t care) Capacitance − (don’t care) (Settings at shipment: Resonator: 4 MHz Capacitance: 15 pF) (Open) 1 2 3 4 (Open) 5 6 7 8 8-pin header (standard accessory) 1 2 3 4 5 6 7 8 OSC1 Oscillator on IE-703217G1-EM1 Shorted pins Mount oscillator Shorted pins on X1 socket. Set configuration clock to “Internal”. . +5V (Open) (Open) 1 2 (Open) 3 4 5 (Open) 6 7 1 8 2 7 3 6 4 5 8 Clock output OSC1 Oscillator on target system Shorted pins Mount oscillator Shorted pins on X1 socket. Caution Always input a square wave. Set configuration clock to “Target”. +5V (Open) (Open) 1 2 (Open) 3 4 5 (Open) 6 7 1 8 2 7 3 6 4 5 8 OSC1 User’s Manual U16594EJ1V0UM Clock output 19 CHAPTER 3 SWITCH SETTINGS 3.2 Pull-Up Resistor Settings Table 3-2 lists the settings for pull-up resistor emulation, which is a mask option of the V850ES/KF1, V850ES/KG1, and V850ES/KJ1. For the location of SW1, refer to Figure 2-1. Table 3-2. Pull-Up Resistor Settings SW1 ON: Port 1 P36 2 P37 3 P38 4 P39 5 P614 6 P615 7 Not used 8 Not used Connect pull-up resistor. OFF: Don’t connect pull-up resistor. Remark 20 All the settings are OFF at shipment. User’s Manual U16594EJ1V0UM CHAPTER 3 SWITCH SETTINGS 3.3 Power-ON Threshold Voltage Settings The threshold voltage used to judge whether the target system is connected (hereafter called "power-ON threshold voltage") is set to 1.7 V at shipment. (Refer to Figure 3-1 JP4 Settings at Shipment.) To change this threshold voltage, insert a 4-pin jumper (standard accessory) on which resistors have been mounted to JP4 as shown in Figure 3-2. For the location of JP4, refer to Figure 2-1. Figure 3-1. JP4 Settings at Shipment 3.9 kΩ 1 2 kΩ 2 3 4 JP4 5V (1.7 V) Voltage comparator VDD from target system Figure 3-2. Changing Power-ON Threshold Voltage R1 R2 Split resistor 1 2 3 4 1 2 3 4 4-pin jumper (standard accessory) JP4 The threshold voltage can be obtained with the following equation. Threshold voltage = 5 V × R2/(R1 + R2) User’s Manual U16594EJ1V0UM 21 CHAPTER 3 SWITCH SETTINGS 3.4 Regulator Output Stabilization Capacitance Setting Jumpers These are the jumpers for connecting the capacitance for stabilizing the output when using the regulator of the V850ES/KF1, V850ES/KG1, or V850ES/KJ1. For the location of JP7 and JP8, refer to Figure 2-1. A 10 µF electrolytic capacitor is mounted on JP8 at shipment. Table 3-3. Regulator Output Stabilization Capacitance Settings Regulator JP7 JP8 − (don’t care) Don’t use (setting at shipment) 1 3 + Use 1 3 Output stabilization capacitance 2-pin jumper (standard accessory) JP8 To REGC pin of emulation CPU 22 User’s Manual U16594EJ1V0UM 1 2 1 2 CHAPTER 4 SETUP PROCEDURE This chapter describes how to connect the IE-703217-G1-EM1 and related products. 4.1 Removing Probe and Replacing Clock Module <1> Hold the IE-703217-G1-EM1 by placing the fingers at the two locations indicated by the arrows and pull out front cover 1. Figure 4-1. Opening/Closing Cover Step 1 (Removing Front Cover 1) Front cover 1 User’s Manual U16594EJ1V0UM 23 CHAPTER 4 SETUP PROCEDURE <2> Then remove the probe and change the clock. Figure 4-2. Opening/Closing Cover Step 1 (After Removing Front Cover 1) 24 User’s Manual U16594EJ1V0UM CHAPTER 4 SETUP PROCEDURE 4.2 Removing Emulation Board <1> Place the case down horizontally. <2> Disconnect the power supply cable and the host interface cable. <3> Refer to 4.1 Removing Probe and Replacing Clock Module for the procedure up to the removal of front cover 1. <4> Loosen the 2 screws indicated by the arrows. Figure 4-3. Opening/Closing Cover Step 2 (Loosening Screws) User’s Manual U16594EJ1V0UM 25 CHAPTER 4 SETUP PROCEDURE <5> Holding front cover 2 down, lift the case using the hinges that connect front cover 2 to the rear panel of the case until the case stands vertically. Figure 4-4. Opening/Closing Cover Step 2 (Lifting Front Cover 2) Front cover 2 26 User’s Manual U16594EJ1V0UM CHAPTER 4 SETUP PROCEDURE <6> Remove the 6 screws on the board indicated by the arrows, and replace the board. Figure 4-5. Opening/Closing Cover Step 2 (After Lifting Front Cover 2) User’s Manual U16594EJ1V0UM 27 CHAPTER 4 SETUP PROCEDURE 4.3 Probe Cable Connection The probe cable is connected to the IE-703217-G1-EM1 at shipment. To remove the probe cable, use the following procedure. (1) To remove the probe cable <1> Remove front cover 1 of the case. <2> Remove the fixing screws from the EM1 board. <3> Remove the probe cable fixing bracket. Proceed with caution when doing so as one end of the probe cable fixing bracket covers the probe cable positioning mark. <4> Remove the probe cable. <5> Close front cover 1 of the case. Figure 4-6. Probe Cable Attachment Position IE-703217-G1-EM1 board Probe cable Fixing screw Probe cable fixing bracket GXP-AXK/KEL board (2) To connect the probe cable <1> Remove front cover 1 from the case. <2> Insert the probe cable in the socket on the EM1 board. <3> Connect the probe cable fixing bracket so that one end covers the probe cable positioning mark. <4> Tighten the fixing screw. <5> Close front cover 1 of the case. 28 User’s Manual U16594EJ1V0UM CHAPTER 5 CAUTIONS The following cautions apply to the IE-703217-G1-EM1. • Target system connection Before connecting the IE-703217-G1-EM1 and the target system, be sure to set the power supply switch of the IE-V850ES-G1 to OFF. • V850ES/KF1 emulation To perform V850ES/KF1 emulation with the target board unconnected, do so after connecting the conversion adapter (GEA) supplied with the EV-703210GK or EV-703210GC to the probe cable. If emulation is performed without connecting a conversion adapter, the fixed bit values of the following ports become undefined. Bits 6 and 7 of port 3 Bits 2, 3, 4, 5, 10, 11, and 12 of port 9 User’s Manual U16594EJ1V0UM 29 CHAPTER 6 RESTRICTIONS The following restrictions apply to the IE-703217-G1-EM1. Permanent restrictions (1) Clock generator • Emulation of oscillation stabilization time after reset release An oscillation stabilization time is inserted after reset release for the emulation target device, but no oscillation stabilization time is inserted in the in-circuit emulator. • Operating clock after reset The operating clock after reset is fxx/8 in the emulation target device, but in the in-circuit emulator, there may be a period during which the operating clock is not initialized to fxx/8. (This depends on the timing after reset release.) (2) Standby mode set/release timing The standby mode set/release timing differs in the target device and the in-circuit emulator. When the standby mode is set, the timing difference is 1 clock or less, and when it is released, the difference is 2 to 3 clocks. (3) Timing of reset via watchdog timer The reset timing using WDT1, WDT2 overflow differs for the target device and the in-circuit emulator. • Operation during break Since various peripheral functions operate even during breaks in the in-circuit emulator, differences in the operations of the in-circuit emulator and the target device may occur. (However, the watchdog timer counter stops during an in-circuit emulator break.) 30 User’s Manual U16594EJ1V0UM APPENDIX A TARGET INTERFACE CHARACTERISTICS From a functional aspect, the target interface (signals that connect the in-circuit emulator and target system) appears to operate as if an actual device were connected, but there may be differences with the actual device from a performance aspect. The target interface of this product can be any one of the interfaces described in Figures A-1 to A-10. The processing of the target interface for each target device is described in Tables A-1 to A-3. Figure A-1. Equivalent Circuit A Target system side IE system side Port pin Numbered port (other than P9) µPD70F3217 emulation CPU Figure A-2. Equivalent Circuit B Target system side IE system side Same potential as BVDD A Alphabetic port 5V HD151015 (level shifter) B B QS3384Q (bus switch) A EP1K100FC484 (FPGA) 1 MΩ Figure A-3. Equivalent Circuit C Target system side IE system side P9 P9 Same potential as BVDD A 5V HD151015 (level shifter) User’s Manual U16594EJ1V0UM µPD70F3217 emulation CPU B EP1K100FC484 (FPGA) 31 APPENDIX A TARGET INTERFACE CHARACTERISTICS Figure A-4. Equivalent Circuit D Target system side VDD, EVDD, BVDD IE system side µPC393G2 (comparator) IIx100 Ω 1 MΩ G6H-2F (relayNote) + 0.1 µF µPC741G2 (operational amplifier) Note Conducts only when a target system is connected. Figure A-5. Equivalent Circuit E Target system side IE system side AVREF0, AVREF1 G6H-2F (relayNote) AVREFX µPD70F3217 emulation CPU Note Conducts only when a target system is connected. Figure A-6. Equivalent Circuit F Target system side IE system side 3.6 V applied only when target system not connected HSK120 HSK120 74VHCT00 RESET 1 MΩ 32 User’s Manual U16594EJ1V0UM APPENDIX A TARGET INTERFACE CHARACTERISTICS Figure A-7. Equivalent Circuit G 5V Target system side VCC 8 IE system side 5 1A 1Y 1B 2Y µPD70F3217 OSC1 74HC157 4 emulation CPU 1 2 X1 X1 3 4 2A 74LCX04 6 2B 74LCX04 X2 X2 5 7 8 Open Figure A-8. Equivalent Circuit H Target system side IE system side AVSS, VSS, EVSS, BVSS AVSS, VSS, EVSS, BVSS µPD70F3217 emulation CPU User’s Manual U16594EJ1V0UM 33 APPENDIX A TARGET INTERFACE CHARACTERISTICS Figure A-9. Equivalent Circuit I Same potential as VDD of target system, or 5 V Target system side IE system side VPP/IC VPP/IC Open Same potential as VDD of target system, or 5 V µPD70F3217 emulation CPU JP7 3 REGC REGC 2 Open 1 JP8 2 1 Figure A-10. Equivalent Circuit J IE system side Target system side µ PD70F3217 OSC2 emulation CPU 1 2 XT2 Open XT2 3 4 XT1 Open 5 6 7 34 User’s Manual U16594EJ1V0UM 1 MΩ XT1 APPENDIX A TARGET INTERFACE CHARACTERISTICS Table A-1. Pin Correspondence List (V850ES/KJ1 Pin Names) (1/4) V850ES/KJ1 Pin No. Target Interface Name (V850ES/KJ1 Pin Name) In-Circuit Emulator Processing 1 AVREF0 Equivalent circuit E 2 AVSS Equivalent circuit H 3 P10/ANO0 Equivalent circuit A 4 P11/ANO1 Equivalent circuit A 5 AVREF1 Equivalent circuit E 6 P00/TOH0 Equivalent circuit A 7 P01/TOH1 Equivalent circuit A 8 VPP/IC Equivalent circuit I 9 VDD Equivalent circuit D 10 REGC Equivalent circuit I 11 VSS Equivalent circuit H 12 X1 Equivalent circuit G 13 X2 Equivalent circuit G 14 RESET Equivalent circuit F 15 XT1 Equivalent circuit J 16 XT2 Equivalent circuit J 17 P02/NMI Equivalent circuit A 18 P03/INTP0 Equivalent circuit A 19 P04/INTP1 Equivalent circuit A 20 P05/INTP2 Equivalent circuit A 21 P06/INTP3 Equivalent circuit A 22 P40/SI00 Equivalent circuit A 23 P41/SO00 Equivalent circuit A 24 P42/SCK00 Equivalent circuit A 25 P30/TXD0 Equivalent circuit A 26 P31/RXD0 Equivalent circuit A 27 P32/ASCK0 Equivalent circuit A 28 P33/TI000/TO00 Equivalent circuit A 29 P34/TI001 Equivalent circuit A 30 P35/TI010/TO01 Equivalent circuit A 31 P36 Equivalent circuit A 32 P37 Equivalent circuit A 33 EVSS Equivalent circuit H 34 EVDD Equivalent circuit D 35 P38/SDA0 Equivalent circuit A 36 P39/SCL0 Equivalent circuit A 37 P50/TI011/RTP00/KR0 Equivalent circuit A 38 P51/TI50/RTP01/KR1 Equivalent circuit A 39 P52/TO50/RTP02/KR2 Equivalent circuit A 40 P53/SIA0/RTP03/KR3 Equivalent circuit A User’s Manual U16594EJ1V0UM 35 APPENDIX A TARGET INTERFACE CHARACTERISTICS Table A-1. Pin Correspondence List (V850ES/KJ1 Pin Names) (2/4) V850ES/KJ1 Pin No. 36 Target Interface Name (V850ES/KJ1 Pin Name) In-Circuit Emulator Processing 41 P54/SOA0/RTP04/KR4 Equivalent circuit A 42 P55/SCKA0/RTP05/KR5 Equivalent circuit A 43 P60/RTP10 Equivalent circuit A 44 P61/RTP11 Equivalent circuit A 45 P62/RTP12 Equivalent circuit A 46 P63/RTP13 Equivalent circuit A 47 P64/RTP14 Equivalent circuit A 48 P65/RTP15 Equivalent circuit A 49 P66/SI02 Equivalent circuit A 50 P67/SO02 Equivalent circuit A 51 P68/SCK02 Equivalent circuit A 52 P69/TI040 Equivalent circuit A 53 P610/TI041 Equivalent circuit A 54 P611/TO04 Equivalent circuit A 55 P612/TI050 Equivalent circuit A 56 P613/TI051/TO05 Equivalent circuit A 57 P614 Equivalent circuit A 58 P615 Equivalent circuit A 59 P80/RXD2/SDA1 Equivalent circuit A 60 P81/TXD2/SCL1 Equivalent circuit A 61 P90/A0/TXD1/KR6 Equivalent circuit C 62 P91/A1/RXD1/KR7 Equivalent circuit C 63 P92/A2/TI020/TO02 Equivalent circuit C 64 P93/A3/TI021 Equivalent circuit C 65 P94/A4/TI030/TO03 Equivalent circuit C 66 P95/A5/TI031 Equivalent circuit C 67 P96/A6/TI51/TO51 Equivalent circuit C 68 P97/A7/SI01 Equivalent circuit C 69 P98/A8/SO01 Equivalent circuit C 70 P99/A9/SCK01 Equivalent circuit C 71 P910/A10/SIA1 Equivalent circuit C 72 P911/A11/SOA1 Equivalent circuit C 73 P912/A12/SCKA1 Equivalent circuit C 74 P913/A13/INTP4 Equivalent circuit C 75 P914/A14/INTP5 Equivalent circuit C 76 P915/A15/INTP6 Equivalent circuit C 77 PCD0 Equivalent circuit B 78 PCD1 Equivalent circuit B 79 PCD2 Equivalent circuit B 80 PCD3 Equivalent circuit B User’s Manual U16594EJ1V0UM APPENDIX A TARGET INTERFACE CHARACTERISTICS Table A-1. Pin Correspondence List (V850ES/KJ1 Pin Names) (3/4) V850ES/KJ1 Pin No. Target Interface Name (V850ES/KJ1 Pin Name) In-Circuit Emulator Processing 81 PCS0/CS0 Equivalent circuit B 82 PCS1/CS1 Equivalent circuit B 83 PCS2/CS2 Equivalent circuit B 84 PCS3/CS3 Equivalent circuit B 85 PCM0/WAIT Equivalent circuit B 86 PCM1/CLKOUT Equivalent circuit B 87 PCM2/HLDAK Equivalent circuit B 88 PCM3/HLDRQ Equivalent circuit B 89 PCM4 Equivalent circuit B 90 PCM5 Equivalent circuit B 91 PCS4 Equivalent circuit B 92 PCS5 Equivalent circuit B 93 PCS6 Equivalent circuit B 94 PCS7 Equivalent circuit B 95 PCT0/WR0 Equivalent circuit B 96 PCT1/WR1 Equivalent circuit B 97 PCT2 Equivalent circuit B 98 PCT3 Equivalent circuit B 99 PCT4/RD Equivalent circuit B 100 PCT5 Equivalent circuit B 101 PCT6/ASTB Equivalent circuit B 102 PCT7 Equivalent circuit B 103 BVSS Equivalent circuit H 104 BVDD Equivalent circuit D 105 PDL0/AD0 Equivalent circuit B 106 PDL1/AD1 Equivalent circuit B 107 PDL2/AD2 Equivalent circuit B 108 PDL3/AD3 Equivalent circuit B 109 PDL4/AD4 Equivalent circuit B 110 PDL5/AD5 Equivalent circuit B 111 PDL6/AD6 Equivalent circuit B 112 PDL7/AD7 Equivalent circuit B 113 PDL8/AD8 Equivalent circuit B 114 PDL9/AD9 Equivalent circuit B 115 PDL10/AD10 Equivalent circuit B 116 PDL11/AD11 Equivalent circuit B 117 PDL12/AD12 Equivalent circuit B 118 PDL13/AD13 Equivalent circuit B 119 PDL14/AD14 Equivalent circuit B 120 PDL15/AD15 Equivalent circuit B User’s Manual U16594EJ1V0UM 37 APPENDIX A TARGET INTERFACE CHARACTERISTICS Table A-1. Pin Correspondence List (V850ES/KJ1 Pin Names) (4/4) V850ES/KJ1 Pin No. 38 Target Interface Name (V850ES/KJ1 Pin Name) In-Circuit Emulator Processing 121 PDH0/A16 Equivalent circuit B 122 PDH1/A17 Equivalent circuit B 123 PDH2/A18 Equivalent circuit B 124 PDH3/A19 Equivalent circuit B 125 PDH4/A20 Equivalent circuit B 126 PDH5/A21 Equivalent circuit B 127 PDH6/A22 Equivalent circuit B 128 PDH7/A23 Equivalent circuit B 129 P715/ANI15 Equivalent circuit A 130 P714/ANI14 Equivalent circuit A 131 P713/ANI13 Equivalent circuit A 132 P712/ANI12 Equivalent circuit A 133 P711/ANI11 Equivalent circuit A 134 P710/ANI10 Equivalent circuit A 135 P79/ANI9 Equivalent circuit A 136 P78/ANI8 Equivalent circuit A 137 P77/ANI7 Equivalent circuit A 138 P76/ANI6 Equivalent circuit A 139 P75/ANI5 Equivalent circuit A 140 P74/ANI4 Equivalent circuit A 141 P73/ANI3 Equivalent circuit A 142 P72/ANI2 Equivalent circuit A 143 P71/ANI1 Equivalent circuit A 144 P70/ANI0 Equivalent circuit A User’s Manual U16594EJ1V0UM APPENDIX A TARGET INTERFACE CHARACTERISTICS Table A-2. Pin Correspondence List (V850ES/KG1 Pin Names) (1/3) V850ES/KG1 Pin No. Target Interface Name (V850ES/KG1 Pin Name) In-Circuit Emulator Processing 1 AVREF0 Equivalent circuit E 2 AVSS Equivalent circuit H 3 P10/ANO0 Equivalent circuit A 4 P11/ANO1 Equivalent circuit A 5 AVREF1 Equivalent circuit E 6 P00/TOH0 Equivalent circuit A 7 P01/TOH1 Equivalent circuit A 8 VPP/IC Equivalent circuit I 9 VDD Equivalent circuit D 10 REGC Equivalent circuit I 11 VSS Equivalent circuit H 12 X1 Equivalent circuit G 13 X2 Equivalent circuit G 14 RESET Equivalent circuit F 15 XT1 Equivalent circuit J 16 XT2 Equivalent circuit J 17 P02/NMI Equivalent circuit A 18 P03/INTP0 Equivalent circuit A 19 P04/INTP1 Equivalent circuit A 20 P05/INTP2 Equivalent circuit A 21 P06/INTP3 Equivalent circuit A 22 P40/SI00 Equivalent circuit A 23 P41/SO00 Equivalent circuit A 24 P42/SCK00 Equivalent circuit A 25 P30/TXD0 Equivalent circuit A 26 P31/RXD0 Equivalent circuit A 27 P32/ASCK0 Equivalent circuit A 28 P33/TI000/TO00 Equivalent circuit A 29 P34/TI001 Equivalent circuit A 30 P35/TI010/TO01 Equivalent circuit A 31 P36 Equivalent circuit A 32 P37 Equivalent circuit A 33 EVSS Equivalent circuit H 34 EVDD Equivalent circuit D 35 P38/SDA0 Equivalent circuit A 36 P39/SCL0 Equivalent circuit A 37 P50/TI011/RTP00/KR0 Equivalent circuit A 38 P51/TI50/RTP01/KR1 Equivalent circuit A 39 P52/TO50/RTP02/KR2 Equivalent circuit A 40 P53/SIA0/RTP03/KR3 Equivalent circuit A User’s Manual U16594EJ1V0UM 39 APPENDIX A TARGET INTERFACE CHARACTERISTICS Table A-2. Pin Correspondence List (V850ES/KG1 Pin Names) (2/3) V850ES/KG1 Pin No. 40 Target Interface Name (V850ES/KG1 Pin Name) In-Circuit Emulator Processing 41 P54/SOA0/RTP04/KR4 Equivalent circuit A 42 P55/SCKA0/RTP05/KR5 Equivalent circuit A 43 P90/A0/TXD1/KR6 Equivalent circuit C 44 P91/A1/RXD1/KR7 Equivalent circuit C 45 P92/A2/TI020/TO02 Equivalent circuit C 46 P93/A3/TI021 Equivalent circuit C 47 P94/A4/TI030/TO03 Equivalent circuit C 48 P95/A5/TI031 Equivalent circuit C 49 P96/A6/TI51/TO51 Equivalent circuit C 50 P97/A7/SI01 Equivalent circuit C 51 P98/A8/SO01 Equivalent circuit C 52 P99/A9/SCK01 Equivalent circuit C 53 P910/A10/SIA1 Equivalent circuit C 54 P911/A11/SOA1 Equivalent circuit C 55 P912/A12/SCKA1 Equivalent circuit C 56 P913/A13/INTP4 Equivalent circuit C 57 P914/A14/INTP5 Equivalent circuit C 58 P915/A15/INTP6 Equivalent circuit C 59 PCS0/CS0 Equivalent circuit B 60 PCS1/CS1 Equivalent circuit B 61 PCM0/WAIT Equivalent circuit B 62 PCM1/CLKOUT Equivalent circuit B 63 PCM2/HLDAK Equivalent circuit B 64 PCM3/HLDRQ Equivalent circuit B 65 PCT0/WR0 Equivalent circuit B 66 PCT1/WR1 Equivalent circuit B 67 PCT4/RD Equivalent circuit B 68 PCT6/ASTB Equivalent circuit B 69 BVSS Equivalent circuit H 70 BVDD Equivalent circuit D 71 PDL0/AD0 Equivalent circuit B 72 PDL1/AD1 Equivalent circuit B 73 PDL2/AD2 Equivalent circuit B 74 PDL3/AD3 Equivalent circuit B 75 PDL4/AD4 Equivalent circuit B 76 PDL5/AD5 Equivalent circuit B 77 PDL6/AD6 Equivalent circuit B 78 PDL7/AD7 Equivalent circuit B 79 PDL8/AD8 Equivalent circuit B 80 PDL9/AD9 Equivalent circuit B User’s Manual U16594EJ1V0UM APPENDIX A TARGET INTERFACE CHARACTERISTICS Table A-2. Pin Correspondence List (V850ES/KG1 Pin Names) (3/3) V850ES/KG1 Pin No. Target Interface Name (V850ES/KG1 Pin Name) In-Circuit Emulator Processing 81 PDL10/AD10 Equivalent circuit B 82 PDL11/AD11 Equivalent circuit B 83 PDL12/AD12 Equivalent circuit B 84 PDL13/AD13 Equivalent circuit B 85 PDL14/AD14 Equivalent circuit B 86 PDL15/AD15 Equivalent circuit B 87 PDH0/A16 Equivalent circuit B 88 PDH1/A17 Equivalent circuit B 89 PDH2/A18 Equivalent circuit B 90 PDH3/A19 Equivalent circuit B 91 PDH4/A20 Equivalent circuit B 92 PDH5/A21 Equivalent circuit B 93 P77/ANI7 Equivalent circuit A 94 P76/ANI6 Equivalent circuit A 95 P75/ANI5 Equivalent circuit A 96 P74/ANI4 Equivalent circuit A 97 P73/ANI3 Equivalent circuit A 98 P72/ANI2 Equivalent circuit A 99 P71/ANI1 Equivalent circuit A 100 P70/ANI0 Equivalent circuit A User’s Manual U16594EJ1V0UM 41 APPENDIX A TARGET INTERFACE CHARACTERISTICS Table A-3. Pin Correspondence List (V850ES/KF1 Pin Names) (1/2) V850ES/KF1 Pin No. 42 Target Interface Name (V850ES/KF1 Pin Name) In-Circuit Emulator Processing 1 AVREF0 Equivalent circuit E 2 AVSS Equivalent circuit H 3 P00/TOH0 Equivalent circuit A 4 P01/TOH1 Equivalent circuit A 5 P02/NMI Equivalent circuit A 6 P03/INTP0 Equivalent circuit A 7 P04/INTP1 Equivalent circuit A 8 VPP/IC Equivalent circuit I 9 VDD Equivalent circuit D 10 REGC Equivalent circuit I 11 VSS Equivalent circuit H 12 X1 Equivalent circuit G 13 X2 Equivalent circuit G 14 RESET Equivalent circuit F 15 XT1 Equivalent circuit J 16 XT2 Equivalent circuit J 17 P05/INTP2 Equivalent circuit A 18 P06/INTP3 Equivalent circuit A 19 P40/SI00 Equivalent circuit A 20 P41/SO00 Equivalent circuit A 21 P42/SCK00 Equivalent circuit A 22 P30/TXD0 Equivalent circuit A 23 P31/RXD0 Equivalent circuit A 24 P32/ASCK0 Equivalent circuit A 25 P33/TI000/TO00 Equivalent circuit A 26 P34/TI001 Equivalent circuit A 27 P35/TI010/TO01 Equivalent circuit A 28 P38/SDA0 Equivalent circuit A 29 P39/SCL0 Equivalent circuit A 30 EVSS Equivalent circuit H 31 EVDD Equivalent circuit D 32 P50/TI011/RTP00/KR0 Equivalent circuit A 33 P51/TI50/RTP01/KR1 Equivalent circuit A 34 P52/TO50/RTP02/KR2 Equivalent circuit A 35 P53/SIA0/RTP03/KR3 Equivalent circuit A 36 P54/SOA0/RTP04/KR4 Equivalent circuit A 37 P55/SCKA0/RTP05/KR5 Equivalent circuit A 38 P90/A0/TXD1/KR6 Equivalent circuit C 39 P91/A1/RXD1/KR7 Equivalent circuit C 40 P96/A6/TI51/TO51 Equivalent circuit C User’s Manual U16594EJ1V0UM APPENDIX A TARGET INTERFACE CHARACTERISTICS Table A-3. Pin Correspondence List (V850ES/KF1 Pin Names) (2/2) V850ES/KF1 Pin No. Target Interface Name (V850ES/KF1 Pin Name) In-Circuit Emulator Processing 41 P97/A7/SI01 Equivalent circuit C 42 P98/A8/SO01 Equivalent circuit C 43 P99/A9/SCK01 Equivalent circuit C 44 P913/A13/INTP4 Equivalent circuit C 45 P914/A14/INTP5 Equivalent circuit C 46 P915/A15/INTP6 Equivalent circuit C 47 PCS0/CS0 Equivalent circuit B 48 PCS1/CS1 Equivalent circuit B 49 PCM0/WAIT Equivalent circuit B 50 PCM1/CLKOUT Equivalent circuit B 51 PCM2/HLDAK Equivalent circuit B 52 PCM3/HLDRQ Equivalent circuit B 53 PCT0/WR0 Equivalent circuit B 54 PCT1/WR1 Equivalent circuit B 55 PCT4/RD Equivalent circuit B 56 PCT6/ASTB Equivalent circuit B 57 PDL0/AD0 Equivalent circuit B 58 PDL1/AD1 Equivalent circuit B 59 PDL2/AD2 Equivalent circuit B 60 PDL3/AD3 Equivalent circuit B 61 PDL4/AD4 Equivalent circuit B 62 PDL5/AD5 Equivalent circuit B 63 PDL6/AD6 Equivalent circuit B 64 PDL7/AD7 Equivalent circuit B 65 PDL8/AD8 Equivalent circuit B 66 PDL9/AD9 Equivalent circuit B 67 PDL10/AD10 Equivalent circuit B 68 PDL11/AD11 Equivalent circuit B 69 PDL12/AD12 Equivalent circuit B 70 PDL13/AD13 Equivalent circuit B 71 PDL14/AD14 Equivalent circuit B 72 PDL15/AD15 Equivalent circuit B 73 P77/ANI7 Equivalent circuit A 74 P76/ANI6 Equivalent circuit A 75 P75/ANI5 Equivalent circuit A 76 P74/ANI4 Equivalent circuit A 77 P73/ANI3 Equivalent circuit A 78 P72/ANI2 Equivalent circuit A 79 P71/ANI1 Equivalent circuit A 80 P70/ANI0 Equivalent circuit A User’s Manual U16594EJ1V0UM 43 APPENDIX B EXTERNAL VIEWS (1) EV-703210GC (for 80GC) Unit: mm Dimensions with GX-Probe connected Dimensions with IC mounted 39 24.1 32 21.8 25.3 14.4 12.8 7.2 7.2 Target connector for 80GC 17 39 2 1 7.1 17 1 12.35 0.65x19=12.35 15 16 C1.5 N 80-14-0.65 CTC APAN 40 2 TOP VIEW 44 BOTTOM VIEW User’s Manual U16594EJ1V0UM APPENDIX B EXTERNAL VIEWS Conversion adapter for 80GC C1.5 JAPAN 1 49 39 19 1.6 MR1 2 MR2 2 40 703210GC-EA-B MR3 2 50 703210GC-EA-B 49 1 CN2 1 2 1 40 10.75 29.7 JAPAN 1.6 2 10.75 NEC 7.1 1 3.2 TOP VIEW 1.6 BOTTOM VIEW IC mounting adapter for 80GC 24.1 3-R2.5 JAPAN 24.1 TET 1 40 TOP VIEW 1 GMA80 -14-0.65 39 080SB C1.5 20 7.1 C2.0 2 BOTTOM VIEW User’s Manual U16594EJ1V0UM 45 APPENDIX B EXTERNAL VIEWS (2) EV-703210GK (for 80GK) Unit: mm Dimensions with GX-Probe connected Dimensions with IC mounted 39 21.0 32 21.8 25.3 14.4 12.8 7.2 7.2 Target connector for 80GK 15 C1.5 GTC80 13 14 0.5x19=9.5 9.5 2 1 7.1 15 1 -12-0.5 AL JAPAN 2 TOP VIEW 46 BOTTOM VIEW User’s Manual U16594EJ1V0UM APPENDIX B EXTERNAL VIEWS Conversion adapter for 80GK C1.5 JAPAN CN2 1 2 1 40 39 2 JAPANCN1-H 1 50 49 2 40 CN1-H MR3MR2 MR1 7.1 39 10.75 703210GK-EA-B 49 1 10.75 29.7 2 NEC 1.6 1 2 19 1.6 3.2 TOP VIEW 1.6 BOTTOM VIEW IC mounting adapter for 80GK 21 18 21 JAPAN TET 080SB TOP VIEW 1 2 1 18 GMA80-12-0.5 C1.5 7.1 3-R2.5 C2.0 BOTTOM VIEW User’s Manual U16594EJ1V0UM 47 APPENDIX B EXTERNAL VIEWS (3) EV-703214GC (for 100GC) Unit: mm Dimensions with GX-Probe connected Dimensions with IC mounted 39 23 32 21.8 25.3 14.4 12.8 7.2 7.2 Target connector for 100GC 17 C1.5 GTC100 -14-0.5 15 16 12 0.5x24=12.0 2 1 8 17 1 JAPAN 2 TOP VIEW 48 BOTTOM VIEW User’s Manual U16594EJ1V0UM APPENDIX B EXTERNAL VIEWS Conversion adapter for 100GC 19 1 GEA100-14-0.5 CN2 1 4 10.75 NEC 2 1 50 2 CN1 1 50 JAPAN 49 10.75 29.7 49 2 GEA100-14-0.5 49 1 50 CN1 4 C1.5 2 JAPAN 2 TOP VIEW BOTTOM VIEW IC mounting adapter for 100GC 4-Ø3.2 20 23 C1.5 100SD TOP VIEW 2 1 4 23 JAPAN TET 4 GMA100-14-0.5 1 BOTTOM VIEW User’s Manual U16594EJ1V0UM 49 APPENDIX B EXTERNAL VIEWS (4) EV-703217GJ (for 144GJ) Unit: mm Dimensions with GX-Probe connected Dimensions with IC mounted 39 32 29 21.8 25.3 14.4 12.8 7.2 7.2 Target connector for 144GJ C1.5 23 TC-144-20-0.5 21 22 23 JAPAN 21 0.5x35=17.5 17.5 TC-144-20-0.5 21 7.1 49 7.1 1 JAPAN 2 50 2 TOP VIEW 50 BOTTOM VIEW User’s Manual U16594EJ1V0UM APPENDIX B EXTERNAL VIEWS Conversion adapter for 144GJ 19 49 2 CN1 1 50 JAPAN 49 7.1 10.75 2 CN3 EA-144-20-0.5 49 1 EA-144-20-0.5 CN3 49 1 10.75 29.7 1 50 49 2 1 CN 2 2 1 50 CN1 JAPAN 2 TOP VIEW 7.1 C1.5 BOTTOM VIEW IC mounting adapter for 144GJ GMA144-20-0.5 49 29 TET 144 SD 50 TOP VIEW 1 1 2 1 7.1 23 3-R2.5 7.1 29 JAPAN C2.0 2 BOTTOM VIEW User’s Manual U16594EJ1V0UM 51 APPENDIX B EXTERNAL VIEWS (5) Emulation probe cable Unit: mm (44) (400) GXP-CABLE-TARGET NEC (32) (32) GXP-CABLE-EML NEC MADE IN JAPAN (12.5) 3 52 (39) User’s Manual U16594EJ1V0UM JAPAN