ISSI IS61LV5128AL ® 512K x 8 HIGH-SPEED CMOS STATIC RAM APRIL 2005 FEATURES • High-speed access times: 10, 12 ns • High-performance, low-power CMOS process • Multiple center power and ground pins for greater noise immunity • Easy memory expansion with CE and OE options • CE power-down • Fully static operation: no clock or refresh required • TTL compatible inputs and outputs • Single 3.3V power supply • Packages available: – 36-pin 400-mil SOJ – 36-pin miniBGA – 44-pin TSOP (Type II) • Lead-free available DESCRIPTION The ISSI IS61LV5128AL is a very high-speed, low power, 524,288-word by 8-bit CMOS static RAM. The IS61LV5128AL is fabricated using ISSI's high-performance CMOS technology. This highly reliable process coupled with innovative circuit design techniques, yields higher performance and low power consumption devices. When CE is HIGH (deselected), the device assumes a standby mode at which the power dissipation can be reduced down to 250 µW (typical) with CMOS input levels. The IS61LV5128AL operates from a single 3.3V power supply and all inputs are TTL-compatible. The IS61LV5128AL is available in 36-pin 400-mil SOJ, 36pin mini BGA, and 44-pin TSOP (Type II) packages. FUNCTIONAL BLOCK DIAGRAM A0-A18 DECODER 512K X 8 MEMORY ARRAY I/O DATA CIRCUIT COLUMN I/O VDD GND I/O0-I/O7 CE OE CONTROL CIRCUIT WE Copyright © 2005 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. C 04/15/05 1 ISSI IS61LV5128AL ® PIN CONFIGURATION 44-Pin TSOP (Type II) 36 mini BGA 1 2 3 4 5 6 A A0 A1 NC A3 A6 A8 B I/O4 A2 WE A4 A7 I/O0 C I/O5 NC A5 D GND VDD E VDD GND F I/O6 G I/O7 H A9 NC NC A0 A1 A2 A3 A4 CE I/O0 I/O1 VDD GND I/O2 I/O3 WE A5 A6 A7 A8 A9 NC NC I/O1 A18 A17 OE CE A16 A15 I/O3 A10 A11 A12 A13 A14 I/O2 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 NC NC NC A18 A17 A16 A15 OE I/O7 I/O6 GND VDD I/O5 I/O4 A14 A13 A12 A11 A10 NC NC NC 36-Pin SOJ PIN DESCRIPTIONS A0-A18 Address Inputs A0 1 36 NC CE Chip Enable Input A1 2 35 A18 Output Enable Input A2 3 34 A17 A3 4 33 A16 A4 5 32 A15 OE WE Write Enable Input I/O0-I/O7 Bidirectional Ports VDD Power GND Ground NC CE 6 31 OE I/O0 7 30 I/O7 I/O1 8 29 I/O6 VDD 9 28 GND GND 10 27 VDD I/O2 11 26 I/O5 I/O3 12 25 I/O4 WE 13 24 A14 A5 14 23 A13 A6 15 22 A12 VDD Current A7 16 21 A11 A8 17 20 A10 A9 18 19 NC No Connection TRUTH TABLE Mode WE Not Selected (Power-down) Output Disabled Read Write 2 CE OE I/O Operation X H X High-Z ISB1, ISB2 H H L L L L H L X High-Z DOUT DIN ICC ICC ICC Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. C 04/15/05 ISSI IS61LV5128AL ® ABSOLUTE MAXIMUM RATINGS(1) Symbol VTERM TSTG PT Parameter Terminal Voltage with Respect to GND Storage Temperature Power Dissipation Value –0.5 to VDD + 0.5 –65 to +150 1.0 Unit V °C W Notes: 1. Stress greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. OPERATING RANGE VDD Range Ambient Temperature 10ns 12ns 0°C to +70°C 3.3V +10%, -5% 3.3V +10% -40°C to +85°C 3.3V +10%, -5% 3.3V +10% Commercial Industrial CAPACITANCE(1,2) Symbol Parameter CIN Input Capacitance CI/O Input/Output Capacitance Conditions Max. Unit VIN = 0V 6 pF VOUT = 0V 8 pF Notes: 1. Tested initially and after any design or process changes that may affect these parameters. 2. Test conditions: TA = 25°C, f = 1 MHz, VDD = 3.3V. Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. C 04/15/05 3 ISSI IS61LV5128AL ® DC ELECTRICAL CHARACTERISTICS (Over Operating Range) Symbol Parameter Test Conditions Min. Max. Unit VOH Output HIGH Voltage VDD = Min., IOH = –4.0 mA 2.4 — V VOL Output LOW Voltage VDD = Min., IOL = 8.0 mA — 0.4 V VIH Input HIGH Voltage 2.0 VDD + 0.3 V –0.3 0.8 V (1) VIL Input LOW Voltage ILI Input Leakage GND ≤ VIN ≤ VDD Com. Ind. –2 –5 2 5 µA ILO Output Leakage GND ≤ VOUT ≤ VDD, Outputs Disabled Com. Ind. –2 –5 2 5 µA Note: 1. VIL = –3.0V for pulse width less than 10 ns. POWER SUPPLY CHARACTERISTICS(1) (Over Operating Range) Symbol Parameter -10 Min. Max. Test Conditions -12 Min. Max. Unit ICC VDD Dynamic Operating Supply Current VDD = Max., Com. IOUT = 0 mA, f = fMAX Ind. — — 90 95 — — 85 90 mA ISB TTL Standby Current (TTL Inputs) VDD = Max., VIN = VIH or VIL CE ≥ VIH, f = fMAX. Com. Ind. — — 40 45 — — 35 40 mA ISB1 TTL Standby Current (TTL Inputs) VDD = Max., VIN = VIH or VIL CE ≥ VIH, f = 0 Com. Ind. — — 20 25 — — 20 25 mA ISB2 CMOS Standby Current (CMOS Inputs) VDD = Max., Com. CE ≥ VDD – 0.2V, Ind. VIN ≥ VDD – 0.2V, or VIN ≤ 0.2V, f = 0 — — 15 20 — — 15 20 mA Note: 1. At f = fMAX, address and data inputs are cycling at the maximum frequency, f = 0 means no input lines change. 4 Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. C 04/15/05 ISSI IS61LV5128AL ® READ CYCLE SWITCHING CHARACTERISTICS(1) (Over Operating Range) Symbol -10 Min. Max. Parameter tRC tAA tOHA tACE tDOE tHZOE(2) tLZOE(2) tHZCE(2 tLZCE(2) tPU tPD -12 Min. Max. Unit Read Cycle Time 10 — 12 — ns Address Access Time — 10 — 12 ns Output Hold Time 2 — 2 — ns CE Access Time — 10 — 12 ns OE Access Time — 4 — 5 ns OE to High-Z Output — 4 — 5 ns OE to Low-Z Output 0 — 0 — ns CE to High-Z Output 0 4 0 6 ns CE to Low-Z Output 3 — 3 — ns Power Up Time 0 — 0 — ns Power Down Time — 10 — 12 ns Notes: 1. Test conditions assume signal transition times of 3 ns or less, timing reference levels of 1.5V, input pulse levels of 0V to 3.0V and output loading specified in Figure 1. 2. Tested with the load in Figure 2. Transition is measured ±500 mV from steady-state voltage. AC TEST CONDITIONS Parameter Input Pulse Level Input Rise and Fall Times Input and Output Timing and Reference Levels Output Load Unit 0V to 3.0V 3 ns 1.5V See Figures 1 and 2 AC TEST LOADS 319 Ω 319 Ω 3.3V 3.3V OUTPUT OUTPUT 30 pF Including jig and scope Figure 1 353 Ω 5 pF Including jig and scope Figure 2 Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. C 04/15/05 353 Ω 5 ISSI IS61LV5128AL ® AC WAVEFORMS READ CYCLE NO. 1(1,2) (Address Controlled) (CE = OE = VIL) t RC ADDRESS t AA t OHA t OHA DOUT DATA VALID PREVIOUS DATA VALID READ1.eps READ CYCLE NO. 2(1,3) (CE and OE Controlled) t RC ADDRESS t AA t OHA OE t HZOE t DOE t LZOE CE t ACE t HZCE t LZCE DOUT HIGH-Z DATA VALID CE_RD2.eps Notes: 1. WE is HIGH for a Read Cycle. 2. The device is continuously selected. OE, CE = VIL. 3. Address is valid prior to or coincident with CE LOW transitions. 6 Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. C 04/15/05 ISSI IS61LV5128AL ® WRITE CYCLE SWITCHING CHARACTERISTICS(1,3) (Over Operating Range) Symbol -10 Min. Max. Parameter -12 Min. Max. Unit tWC Write Cycle Time 10 — 12 — ns tSCE CE to Write End 8 — 8 — ns tAW Address Setup Time to Write End 8 — 8 — ns tHA Address Hold from Write End 0 — 0 — ns tSA Address Setup Time 0 — 0 — ns tPWE1 WE Pulse Width 8 — 8 — ns tPWE2 WE Pulse Width (OE = LOW) 10 — 12 — ns tSD Data Setup to Write End 6 — 6 — ns tHD Data Hold from Write End 0 — 0 — ns tHZWE(2) WE LOW to High-Z Output — 5 — 6 ns tLZWE(2) WE HIGH to Low-Z Output 2 — 2 — ns Notes: 1. Test conditions assume signal transition times of 3 ns or less, timing reference levels of 1.5V, input pulse levels of 0V to 3.0V and output loading specified in Figure 1. 2. Tested with the load in Figure 2. Transition is measured ±500 mV from steady-state voltage. Not 100% tested. 3. The internal write time is defined by the overlap of CE LOW and WE LOW. All signals must be in valid states to initiate a Write, but any one can go inactive to terminate the Write. The Data Input Setup and Hold timing are referenced to the rising or falling edge of the signal that terminates the write. AC WAVEFORMS WRITE CYCLE NO. 1(1,2) (CE Controlled, OE = HIGH or LOW) t WC VALID ADDRESS ADDRESS t SA t SCE t HA CE t AW t PWE1 t PWE2 WE t HZWE DOUT DATA UNDEFINED t LZWE HIGH-Z t SD DIN t HD DATAIN VALID CE_WR1.eps Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. C 04/15/05 7 ISSI IS61LV5128AL ® WRITE CYCLE NO. 2(1,2) (WE Controlled: OE is HIGH During Write Cycle) t WC ADDRESS VALID ADDRESS t HA OE CE LOW t AW t PWE1 WE t SA DOUT t HZWE t LZWE HIGH-Z DATA UNDEFINED t SD t HD DATAIN VALID DIN CE_WR2.eps Notes: 1. The internal write time is defined by the overlap of CE LOW and WE LOW. All signals must be in valid states to initiate a Write, but any one can go inactive to terminate the Write. The Data Input Setup and Hold timing are referenced to the rising or falling edge of the signal that terminates the Write. 2. I/O will assume the High-Z state if OE > VIH. WRITE CYCLE NO. 3 (WE Controlled: OE is LOW During Write Cycle) t WC ADDRESS VALID ADDRESS OE LOW CE LOW t HA t AW t PWE2 WE t SA DOUT DATA UNDEFINED t HZWE t LZWE HIGH-Z t SD DIN t HD DATAIN VALID CE_WR3.eps 8 Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. C 04/15/05 ISSI IS61LV5128AL ® ORDERING INFORMATION Commercial Range: 0°C to +70°C Speed (ns) Order Part No. Package 10 10 IS61LV5128AL-10K IS61LV5128AL-10T 400-mil Plastic SOJ TSOP (Type II) 12 12 IS61LV5128AL-12K IS61LV5128AL-12T 400-mil Plastic SOJ TSOP (Type II) Industrial Range: –40°C to +85°C Speed (ns) Order Part No. Package 10 10 10 10 10 10 IS61LV5128AL-10KI IS61LV5128AL-10KLI IS61LV5128AL-10TI IS61LV5128AL-10TLI IS61LV5128AL-10BI IS61LV5128AL-10BLI 400-mil Plastic SOJ 400-mil Plastic SOJ, Lead-free TSOP (Type II) TSOP (Type II), Lead-free mini BGA (8mmx10mm) mini BGA (8mmx10mm), Lead-free 12 IS61LV5128AL-12TI TSOP (Type II) Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. C 04/15/05 9 ISSI ® PACKAGING INFORMATION Mini Ball Grid Array Package Code: B (36-pin) Top View Bottom View φ b (36x) 1 2 3 4 5 6 6 A 4 3 2 1 A e B B C C D D D 5 D1 E E F F G G H H e E E1 Notes: 1. Controlling dimensions are in millimeters. A2 A A1 SEATING PLANE mBGA - 6mm x 8mm mBGA - 8mm x 10mm MILLIMETERS INCHES MILLIMETER INCHES Sym. Min. Typ. Max. Min. Typ. Max. Sym. Min. Typ. Max. Min. Typ. Max. N0. Leads 36 36 N0. Leads 36 36 A — — 1.20 — — 0.047 A — — 1.20 — — 0.047 A1 0.24 — 0.30 0.009 — 0.012 A1 0.24 — 0.30 0.009 — 0.012 A2 0.60 — — 0.024 — — A2 0.60 — — 0.024 — — D 7.90 8.00 D 9.90 10.00 10.10 D1 E 8.10 5.25BSC 5.90 6.00 0.311 0.315 0.319 0.207BSC 6.10 D1 0.232 0.236 0.240 E 5.25BSC 7.90 0.390 0.394 0.398 .207BSC 8.00 8.10 0.311 0.315 0.319 E1 3.75BSC 0.148BSC E1 3.75BSC 0.148BSC e 0.75BSC 0.030BSC e 0.75BSC 0.030BSC 0.012 0.014 0.016 b b 0.30 0.35 0.40 0.30 0.35 0.40 0.012 0.014 0.016 Copyright © 2003 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. E 01/15/03 ISSI PACKAGING INFORMATION ® 400-mil Plastic SOJ Package Code: K N Notes: 1. Controlling dimension: millimeters. 2. BSC = Basic lead spacing between centers. 3. Dimensions D and E1 do not include mold flash protrusions and should be measured from the bottom of the package. 4. Reference document: JEDEC MS-027. N/2+1 E1 1 E N/2 SEATING PLANE D b A C A2 e Symbol No. Leads A A1 A2 B b C D E E1 E2 e B Millimeters Inches Min Max Min Max (N) 28 3.25 3.75 0.128 0.148 0.64 — 0.025 — 2.08 — 0.082 — 0.38 0.51 0.015 0.020 0.66 0.81 0.026 0.032 0.18 0.33 0.007 0.013 18.29 18.54 0.720 0.730 11.05 11.30 0.435 0.445 10.03 10.29 0.395 0.405 9.40 BSC 0.370 BSC 1.27 BSC 0.050 BSC A1 E2 Millimeters Min Max Inches Min Max Millimeters Min Max 32 3.25 3.75 0.64 — 2.08 — 0.38 0.51 0.66 0.81 0.18 0.33 20.82 21.08 11.05 11.30 10.03 10.29 9.40 BSC 1.27 BSC 0.128 0.148 0.025 — 0.082 — 0.015 0.020 0.026 0.032 0.007 0.013 0.820 0.830 0.435 0.445 0.395 0.405 0.370 BSC 0.050 BSC 3.25 3.75 0.64 — 2.08 — 0.38 0.51 0.66 0.81 0.18 0.33 23.37 23.62 11.05 11.30 10.03 10.29 9.40 BSC 1.27 BSC Inches Min Max 36 0.128 0.148 0.025 — 0.082 — 0.015 0.020 0.026 0.032 0.007 0.013 0.920 0.930 0.435 0.445 0.395 0.405 0.370 BSC 0.050 BSC Copyright © 2003 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. F 10/29/03 ISSI PACKAGING INFORMATION Millimeters Inches Symbol Min Max Min Max No. Leads (N) 40 A 3.25 3.75 0.128 0.148 A1 0.64 — 0.025 — A2 2.08 — 0.082 — B 0.38 0.51 0.015 0.020 b 0.66 0.81 0.026 0.032 C 0.18 0.33 0.007 0.013 D 25.91 26.16 1.020 1.030 E 11.05 11.30 0.435 0.445 E1 10.03 10.29 0.395 0.405 E2 9.40 BSC 0.370 BSC e 1.27 BSC 0.050 BSC Millimeters Min Max Inches Min Max Millimeters Min Max 42 3.25 3.75 0.64 — 2.08 — 0.38 0.51 0.66 0.81 0.18 0.33 27.18 27.43 11.05 11.30 10.03 10.29 9.40 BSC 1.27 BSC 0.128 0.148 0.025 — 0.082 — 0.015 0.020 0.026 0.032 0.007 0.013 1.070 1.080 0.435 0.445 0.395 0.405 0.370 BSC 0.050 BSC 3.25 3.75 0.64 — 2.08 — 0.38 0.51 0.66 0.81 0.18 0.33 28.45 28.70 11.05 11.30 10.03 10.29 9.40 BSC 1.27 BSC ® Inches Min Max 44 0.128 0.148 0.025 — 0.082 — 0.015 0.020 0.026 0.032 0.007 0.013 1.120 1.130 0.435 0.445 0.395 0.405 0.370 BSC 0.050 BSC Copyright © 2003 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. 2 Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. F 10/29/03 ISSI ® PACKAGING INFORMATION Plastic TSOP Package Code: T (Type II) N N/2+1 E1 1 Notes: 1. Controlling dimension: millimieters, unless otherwise specified. 2. BSC = Basic lead spacing between centers. 3. Dimensions D and E1 do not include mold flash protrusions and should be measured from the bottom of the package. 4. Formed leads shall be planar with respect to one another within 0.004 inches at the seating plane. E N/2 D SEATING PLANE A ZD . b e Symbol Ref. Std. No. Leads A A1 b C D E1 E e L ZD α Millimeters Min Max Inches Min Max (N) 32 — 1.20 — 0.047 0.05 0.15 0.002 0.006 0.30 0.52 0.012 0.020 0.12 0.21 0.005 0.008 20.82 21.08 0.820 0.830 10.03 10.29 0.391 0.400 11.56 11.96 0.451 0.466 1.27 BSC 0.050 BSC 0.40 0.60 0.016 0.024 0.95 REF 0.037 REF 0° 5° 0° 5° L α A1 Plastic TSOP (T - Type II) Millimeters Inches Min Max Min Max 44 — 1.20 — 0.047 0.05 0.15 0.002 0.006 0.30 0.45 0.012 0.018 0.12 0.21 0.005 0.008 18.31 18.52 0.721 0.729 10.03 10.29 0.395 0.405 11.56 11.96 0.455 0.471 0.80 BSC 0.032 BSC 0.41 0.60 0.016 0.024 0.81 REF 0.032 REF 0° 5° 0° 5° Millimeters Min Max C Inches Min Max 50 — 1.20 0.05 0.15 0.30 0.45 0.12 0.21 20.82 21.08 10.03 10.29 11.56 11.96 0.80 BSC 0.40 0.60 0.88 REF 0° 5° — 0.047 0.002 0.006 0.012 0.018 0.005 0.008 0.820 0.830 0.395 0.405 0.455 0.471 0.031 BSC 0.016 0.024 0.035 REF 0° 5° Copyright © 2003 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. F 06/18/03