±16.5kV ESD Protected, 1.8V, Micro Power, +125°C, 1/8 Unit Load, RS-485/RS-422 Differential Receivers ISL32610E, ISL32611E, ISL32612E The ISL32610E, ISL32611E, ISL32612E are ±16.5kV IEC61000 ESD protected, fractional unit load (UL), 1.8V powered, single differential receivers (Rx) for balanced (e.g., RS-485) data communication. With their 85µA supply currents, these receivers are optimized for low power applications, and deliver the lowest supply currents of any available single Rx IC (see Figure 1). Features To improve performance in low data rate applications with slow signal transitions, these Rx feature symmetrical switching points (±200mV) and increased hysteresis. The symmetrical switching points eliminate the duty cycle distortion introduced by “full-failsafe” type receivers (see Figure 2), while the larger hysteresis increases noise immunity. • Symmetrical Switching Thresholds for Less Duty Cycle Distortion (see Figure 2) • Wide Supply Voltage Range . . . . . . . . . . . . . . . . . 1.8V to 3.6V • Ultra Low Quiescent Supply Current . . . . . . . . . 110µA (Max.) • IEC61000 ESD Protection on RS-485 Bus Pins . . . . ±16.5kV - Class 3 ESD Level on all Other Pins. . . . . . . . . . >8kV HBM • 5V Tolerant Logic Inputs • Pb-Free (RoHS Compliant) Applications • Industrial/Process Control Networks, Factory Automation • High Node Count Networks • Space Constrained Systems See Table 1 for a summary of each device’s features. For a companion 1.8V differential transmitter in a SOT-23 package, reference the ISL32613E data sheet. ISL3282E STATIC ICC (µA) 250 200 150 DYNAMIC (256kbps) ISL3261XE STATIC 50 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 RECEIVER OUTPUT (V) RECEIVER INPUT (V) • Building Environmental Control Systems DYNAMIC (256kbps) 100 • 1/8 Unit Load Allows up to 256 Devices on the RS-485 Bus • Three State Rx Output Available Receiver inputs feature a “failsafe-if-open” design, which ensures a logic high Rx output if Rx inputs are floating. Data rates up to 256kbps are achievable with this device at VCC = 1.8V. 300 • Data Rates up to 256kbps (1.8V) or 500kbps (3.3V) • Specified for +125°C Operation Receivers present a 1/8 “unit load” to the data bus, which allows up to 256 devices on the network for large node count systems (e.g., process automation, remote meter reading systems). The ISL32611E/ISL32612E Rx output is tri-statable via the RE/RE input. 500 450 400 350 • Larger Hysteresis for Improved Noise Immunity . . . . . 70mV 1 A-B 0 -1 4 ISL3261XE 0 4 ISL3282E 0 VCC = 3.3V, DATA RATE = 125kbps TIME (4µs/DIV) VCC (V) FIGURE 1. ISL3261XE REDUCES OPERATING ICC BY A FACTOR OF 4 FROM PREVIOUS GENERATION RECEIVER ICs, AND OPERATES WITH SUPPLY VOLTAGES AS LOW AS 1.8V October 21, 2011 FN7869.0 1 FIGURE 2. COMPARED WITH A FULL-FAILSAFE RECEIVER, THE SYMMETRICAL RX THRESHOLDS OF THE ISL3261XE DELIVER LESS OUTPUT DUTY CYCLE DISTORTION WHEN DRIVEN WITH SLOW INPUT SIGNALS CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Copyright Intersil Americas Inc. 2011. All Rights Reserved Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries. All other trademarks mentioned are the property of their respective owners. ISL32610E, ISL32611E, ISL32612E TABLE 1. SUMMARY OF FEATURES PART NUMBER NO. OF DEVICES ALLOWED ON BUS CONFIGURATION 1.8V, 3.3V DATA RATE (kbps) QUIESCENT ICC (µA) Rx ENABLE? LOW POWER SHUTDOWN? PIN COUNT ISL32610E Rx Only 256 256, 500 No 85 No 5 ISL32611E Rx Only 256 256, 500 Yes, Active Low 85 Yes 6 ISL32612E Rx Only 256 256, 500 Yes, Active High 85 Yes 6 Ordering Information PART NUMBER (Notes 1, 2, 3, 4) PART MARKING PACKAGE Tape & Reel (Pb-Free) TEMP. RANGE (°C) PKG. DWG. # ISL32610EFHZ-T 610F -40 to +125 5 Ld SOT-23 P5.064 ISL32610EFHZ-T7A 610F -40 to +125 5 Ld SOT-23 P5.064 ISL32611EFHZ-T 611F -40 to +125 6 Ld SOT-23 P6.064 ISL32611EFHZ-T7A 611F -40 to +125 6 Ld SOT-23 P6.064 ISL32612EFHZ-T 612F -40 to +125 6 Ld SOT-23 P6.064 ISL32612EFHZ-T7A 612F -40 to +125 6 Ld SOT-23 P6.064 NOTES: 1. Please refer to TB347 for details on reel specifications. 2. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 3. For Moisture Sensitivity Level (MSL), please see device information page for ISL32610E, ISL32611E, ISL32612E. For more information on MSL, please see Tech Brief TB363. 4. The part marking is located on the bottom of the part. Pin Configurations ISL32612E (6 LD SOT-23) TOP VIEW ISL32610E (5 LD SOT-23) TOP VIEW VCC 1 GND 2 5 A 4 B ISL32611E (6 LD SOT-23) TOP VIEW 1 GND 2 R RO 3 1 GND 2 R RO 3 VCC VCC R RO 3 6 A 5 RE 4 B Truth Table RECEIVING 6 A 5 RE 4 B INPUTS OUTPUT RE / RE (Note 12) A-B RO 0/1 ≥ +0.2V 1 0/1 ≤ -0.2V 0 0/1 Inputs Open 1 1/0 X High-Z (Note 5) NOTE: 5. Low Power Shutdown Mode (Note 10, except for the ISL32610E) 2 FN7869.0 October 21, 2011 ISL32610E, ISL32611E, ISL32612E Pin Descriptions PIN NUMBER PIN NAME ISL32610E ISL32611E ISL32612E FUNCTION VCC 1 1 1 System power supply input (1.8V to 3.6V). GND 2 2 2 Ground connection. RO 3 3 3 Receiver output: If A > B by at least 0.2V, RO is high; if A < B by 0.2V or more, RO is low; RO = High if A and B are unconnected (floating). B 4 4 4 ±16.5kV IEC61000 ESD Protected, inverting differential receiver input. RE - 5 - Receiver output enable. RO is enabled when RE is low; RO is high impedance when RE is high. If the enable function isn’t needed, connect RE to GND. RE is internally pulled low. RE - - 5 Receiver output enable. RO is enabled when RE is high; RO is high impedance when RE is low. If the enable function isn’t needed, connect RE to VCC through a 1kΩ or greater resistor. RE is internally pulled high. A 5 6 6 ±16.5kV IEC61000 ESD Protected, noninverting differential receiver input. Typical Operating Circuit +1.8V +1.8V + 1 0.1µF 0.1µF + 2 VCC 3 RO VCC R D 5 RE B 4 4 Z A 6 6 Y DE 3 GND GND 2 5 ISL32611E 3 DI 1 ISL32613E FN7869.0 October 21, 2011 ISL32610E, ISL32611E, ISL32612E Absolute Maximum Ratings Thermal Information VCC to Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7V Input Voltages RE, RE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 7V A, B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -8V to +12.5V Output Voltages RO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to (VCC +0.3V) ESD Rating . . . . . . . . . . . . . . See “Electrical Specifications” Table page 5 Latch-up (per JESD78, Level 2, Class A) . . . . . . . . . . . . . . . . . . . . . +125°C Thermal Resistance (Typical) θJA (°C/W) θJC (°C/W) 5 Ld SOT-23 Package (Note 6, 7) . . . . . . . 190 120 6 Ld SOT-23 Package (Note 6, 7) . . . . . . . 177 120 Maximum Junction Temperature (Plastic Package) . . . . . . . . . . . +150°C Storage Temperature Range. . . . . . . . . . . . . . . . . . . . . . . -65°C to +150°C Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp Recommended Operating Conditions Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to +125°C Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.8V to 3.3V Common Mode Input Voltage VCC = 1.8V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -2V to +2V VCC = 3.3V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -7V to +12V CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. NOTES: 6. θJA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details. 7. For θJC, the “case temp” location is taken at the package top center. Electrical Specifications ( Test Conditions: VCC = 1.8V; Unless Otherwise Specified. Typicals are at VCC = 1.8V, TA = +25°C. Boldface limits apply over the operating temperature range, -40°C to +125°C. (Note 9) PARAMETER SYMBOL TEST CONDITIONS TEMP (°C) MIN (Note 8) TYP MAX (Note 8) UNITS DC CHARACTERISTICS Logic Input High Voltage (Note 12) VIH RE, RE VCC = 1.8V Full 1.2 - - V 3V ≤ VCC ≤ 3.6V Full 2 - - V VCC = 1.8V Full - - 0.45 V 3V ≤ VCC ≤ 3.6V Full - - 0.8 V VCC = 1.8V Full -6 - 6 µA VCC ≤ 3.6V Full -12 - 12 µA VIN = 2V Full - - 60 µA VIN = -2V Full -60 - - µA VCC = 0V or 3.6V VIN = 12V Full - - 125 µA VIN = -7V Full -100 - - µA -2V ≤ VCM ≤ 2V VCC = 1.8V Full -0.2 - 0.2 V -7V ≤ VCM ≤ 12V 3V ≤ VCC ≤ 3.6V Full -0.2 - 0.2 V VCC = 1.8V Full - 70 - mV Logic Input Low Voltage (Note 12) VIL RE, RE Logic Input Current (Note 12) IIN1 RE, RE Input Current (A, B) (Note 11) IIN2 VCC = 0V or 1.8V Receiver Differential Threshold Voltage V TH Receiver Input Hysteresis ΔV TH VCM = 0V Full - 70 - mV Receiver Output High Voltage VOH IO = -1mA, VID = 200mV Full VCC - 0.4 - - V Receiver Output Low Voltage VOL IO = 2mA, VID = -200mV Full - - 0.4 V Three-State (High Impedance) Receiver Output Current (Note 12) IOZR 0V ≤ VO ≤ VCC Full -1 - 1 µA Receiver Short-Circuit Current IOSR 0V ≤ VO ≤ VCC Full - - 30 mA 3V ≤ VCC ≤ 3.6V No-Load Supply Current ICC Shutdown Supply Current (Notes 10, 12) ISHDN RE = 0V or RE = VCC Full - 85 110 µA 3V ≤ VCC ≤ 3.6V Full - - 135 µA Full - - 2 µA ISL32611, RE = VCC, VCC ≥ 1.8V ISL32612, RE = 0V 4 VCC = 1.8V VCC = 1.8V Full - - 7 µA VCC ≤ 3.6V Full - - 14 µA FN7869.0 October 21, 2011 ISL32610E, ISL32611E, ISL32612E Electrical Specifications Test Conditions: VCC = 1.8V; Unless Otherwise Specified. Typicals are at VCC = 1.8V, TA = +25°C. Boldface limits apply over the operating temperature range, -40°C to +125°C. (Note 9) (Continued) PARAMETER SYMBOL TEST CONDITIONS TEMP (°C) MIN (Note 8) TYP - MAX (Note 8) UNITS SWITCHING CHARACTERISTICS Maximum Data Rate fMAX Receiver Input to Output Delay tPLH, tPHL Receiver Skew | tPLH - tPHL | tSKD VID = ±1V, VCM = 0V, (Figure 3) VCC = 1.8V Full 256 3V ≤ VCC ≤ 3.6V Full 500 (Figure 3) VCC = 1.8V Full - VCC = 3.3V 25 - (Figure 3) kbps ns 200 - ns - 3 125 ns 25 - 6 - ns VCC = 1.8V Full - 1100 4000 ns VCC = 3.3V 25 - 1500 - ns VCC = 1.8V Full - 1100 4000 ns VCC = 3.3V 25 - 1500 - ns CL = 15pF, SW = GND, (Figure 4, Note 12) VCC = 1.8V Full - 15 75 ns VCC = 3.3V 25 - 6 - ns CL = 15pF, SW = VCC, (Figure 4, Note 12) VCC = 1.8V Full - 15 75 ns VCC = 3.3V 25 - 6 - ns IEC61000-4-2, Air-Gap Discharge Method 25 - ±16.5 - kV IEC61000-4-2, Contact Discharge Method 25 - ±9 - kV Human Body Model, From Bus Pins to GND 25 - ±16.5 - kV Human Body Model (Tested per JESD22-A114E) 25 - ±8 - kV Machine Model (Tested per JESD22-A115-A) 25 - ±400 - V Receiver Enable to Output Low tZL CL = 15pF, SW = VCC, (Figure 4, Note 12) tLZ 1000 Full CL = 15pF, SW = GND, (Figure 4, Note 12) Receiver Disable from Output Low 210 VCC = 1.8V tZH tHZ kbps VCC = 3.3V Receiver Enable to Output High Receiver Disable from Output High - ESD PERFORMANCE RS-485 Pins (A, B) All Pins NOTES: 8. Compliance to data sheet limits is assured by one or more methods: production test, characterization and/or design. 9. Currents into device pins are positive; currents out of device pins are negative. Voltages are referenced to ground unless otherwise specified. 10. The ISL32611E enters SHDN whenever RE switches high, and the ISL32612E enters SHDN whenever RE switches low. 11. Devices meeting these limits are denoted as “1/8 unit load (1/8 UL)” transceivers. The RS-485 standard allows up to 32 Unit Loads on the bus, so there can be 256 1/8 UL devices on a bus. 12. Not applicable to the ISL32610E. Test Circuits and Waveforms GND / VCC B R A +0.5V B RE / RE RO 15pF 0V 0V -0.5V A tPLH tPHL VOH SIGNAL GENERATORS 50% RO 50% VOL FIGURE 3A. TEST CIRCUIT FIGURE 3B. MEASUREMENT POINTS FIGURE 3. RECEIVER PROPAGATION DELAY AND DATA RATE 5 FN7869.0 October 21, 2011 ISL32610E, ISL32611E, ISL32612E Test Circuits and Waveforms (Continued) VCC RE 50% 50% 0V RE / RE VCC B SIGNAL GENERATOR 1kΩ RO R VCC SW A RE 50% 50% 0V GND 15pF tZH OUTPUT HIGH VOH - 0.25V RO PARAMETER A SW tHZ +1V GND tLZ -1V VCC tZH +1V GND tZL -1V VCC FIGURE 4A. TEST CIRCUIT tHZ VOH 50% 0V tZL tLZ VCC RO 50% VOL + 0.25V V OUTPUT LOW OL FIGURE 4B. MEASUREMENT POINTS FIGURE 4. RECEIVER ENABLE AND DISABLE TIMES (EXCLUDING ISL32610E) 6 FN7869.0 October 21, 2011 ISL32610E, ISL32611E, ISL32612E Application Information Features These devices utilize a differential input receiver for maximum noise immunity and common mode rejection. Input sensitivity is ±200mV, as required by the RS-422 and RS-485 standards. These receivers’ symmetrical ±200mV switching thresholds deliver less duty cycle distortion than similar receivers with a full-failsafe design (i.e., skewed low/high input thresholds, (such as -200mV/-20mV) which increase the high bit width). This distortion is especially noticeable when the Rx is driven by slow input transitions (see Figure 2). The symmetrical input thresholds also allow more room for increased input hysteresis, thereby increasing the Rx noise immunity. The 70mV hysteresis of this Rx is twice the amount specified for most full-failsafe devices. Receiver input resistance of 96kΩ surpasses the RS-422 specification of 4kΩ, and is eight times the RS-485 “Unit Load (UL)” requirement of 12kΩ minimum. Thus, these products are known as “one-eighth UL” receivers, and there can be up to 256 of these devices on a network while still complying with the RS-485 loading specification. Receiver inputs function with common mode voltages (CMV) of ±2V with VCC = 1.8V, and with CMVs of -7V to +12V for VCC ≥ 2.7V. All the receivers include a “failsafe-if-open” function that guarantees a high level receiver output if the receiver inputs are unconnected (floating). As mentioned previously, the full-failsafe function is not implemented in order to deliver output duty cycles that better match the input. Receivers support data rates up to 256kbps (VCC = 1.8V) or 500kbps (VCC ≥ 3V), and receiver outputs of the ISL32611E and ISL32612E are three-statable via the active low RE or active high RE input. Data Rate Recommendations When coupled with the ISL32613E or ISL32614E 1.8V transmitter ICs, these receivers are useful for networks up to 4000’ (1220m) long, or for data rates up to 500kbps. For 4000’ distances with VCC = 1.8V, the ISL32613E can be used with any of these receivers at data rates ≤ 50kbps. With VCC = 3.3V, any transmitter / receiver combination operates over 4000’ at rates up to 128kbps. Shorter networks allow data rates up to 500kbps, as shown in Figures 9, 10, 11 and 12. Network termination resistors are only recommended for networks operating at VCC ≥ 2.7V, and using termination resistors may allow for higher data rates. 7 Low Power Shutdown Mode (ISL32611E and ISL32612E) These devices use a fraction of the power required by most differential receivers (see Figure 1 on page 1), but they also include a shutdown feature that reduces the already low quiescent ICC even further. The ISL32611E and ISL32612E enter shutdown whenever the receiver is disabled (RE = GND or RE = VCC). ESD Protection All pins on these devices include class 3 (>6kV) Human Body Model (HBM) ESD protection structures, but the bus pins (Rx inputs) incorporate advanced structures allowing them to survive ESD events in excess of ±16.5kV HBM and ±16.5kV IEC61000. The bus pins are particularly vulnerable to ESD damage because they typically connect to an exposed port on the exterior of the finished product. Simply touching the port pins, or connecting a cable, can cause an ESD event that might destroy unprotected ICs. These new ESD structures protect the device whether or not it is powered up, and without degrading the common mode range. This built-in ESD protection eliminates the need for board-level protection structures (e.g., transient suppression diodes), and the associated, undesirable capacitive load they present. IEC61000-4-2 Testing The IEC61000 test method applies to finished equipment, rather than to an individual IC. Therefore, the pins most likely to suffer an ESD event are those that are exposed to the outside world (the bus pins in this case), and the IC is tested in its typical application configuration (power applied) rather than testing each pin-to-pin combination. The smaller value current limiting resistor coupled with the larger charge storage capacitor yields a test that is much more severe than the HBM test. The extra ESD protection built into this device’s bus pins allows the design of equipment meeting level 4 criteria without the need for additional board-level protection on the I/O port. AIR-GAP DISCHARGE TEST METHOD For the air-gap discharge test method, a charged probe tip moves toward the IC pin until the voltage arcs to it. The current waveform delivered to the IC pin depends on approach speed, humidity, temperature, etc., so it is difficult to obtain repeatable results. The A and B pins withstand ±16.5kV air-gap discharges. CONTACT DISCHARGE TEST METHOD During the contact discharge test, the probe contacts the tested pin before the probe tip is energized, thereby eliminating the variables associated with the air-gap discharge. The result is a more repeatable and predictable test, but equipment limits prevent testing devices at voltages higher than ±9kV. The ISL32610E, ISL32611E, ISL32612E survive ±9kV contact discharges on the bus pins. FN7869.0 October 21, 2011 ISL32610E, ISL32611E, ISL32612E Typical Performance Curves 30 VCC = 1.8V +25°C 8 RECEIVER OUTPUT CURRENT (mA) RECEIVER OUTPUT CURRENT (mA) 10 TA = +25°C; Unless Otherwise Specified +85°C 6 +125°C 4 2 RO LOW 0 RO HIGH -2 +25°C +125°C -4 -6 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 +85°C 20 +125°C 10 RO LOW 0 RO HIGH -10 +85°C +25°C +125°C -20 -30 1.8 +25°C VCC = 3.3V 0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3.0 3.3 RECEIVER OUTPUT VOLTAGE (V) RECEIVER OUTPUT VOLTAGE (V) FIGURE 5. RECEIVER OUTPUT CURRENT vs RECEIVER OUTPUT VOLTAGE (VCC = 1.8V) FIGURE 6. RECEIVER OUTPUT CURRENT vs RECEIVER OUTPUT VOLTAGE (VCC = 3.3V) 105 120 RE = 0V, RE = VCC 500kbps 100 110 VCC = 3.3V 100 95 90 90 256kbps ICC (µA) ICC (µA) 128kbps 80 9.6kbps 85 VCC = 1.8V 70 80 60 75 -15 10 35 60 85 70 1.8 110 125 2.0 1 0 A-B -1 RD = ∞ -2 2 1 0 TIME (10µs/DIV) FIGURE 9. ISL32613E AND ISL32611E PERFORMANCE WITH VCC = 1.8V, 128kbps, 2000’ (610m) CAT 5 CABLE 8 RECEIVER INPUTS (V) 2 2.6 2.8 3.0 3.2 3.4 3.6 5 RECEIVER OUTPUT (V) RECEIVER INPUTS (V) RECEIVER OUTPUT (V) 0 DI 2.4 FIGURE 8. DYNAMIC SUPPLY CURRENT vs SUPPLY VOLTAGE AT DIFFERENT DATA RATES DRIVER INPUT (V) FIGURE 7. STATIC SUPPLY CURRENT vs TEMPERATURE 2 2.2 VCC (V) TEMPERATURE (°C) DRIVER INPUT (V) 50 -40 0 DI 3 2 1 0 A-B -1 -2 -3 RD = ∞ 4 2 0 TIME (10µs/DIV) FIGURE 10. ISL32613E AND ISL32611E PERFORMANCE WITH VCC = 3.3V, 256kbps, 3000’ (915m) CAT 5 CABLE FN7869.0 October 21, 2011 ISL32610E, ISL32611E, ISL32612E RECEIVER OUTPUT (V) 0 DRIVER INPUT (V) RECEIVER INPUTS (V) 2 DI 2 1 0 A-B -1 -2 RD = ∞ 2 1 0 TIME (10µs/DIV) FIGURE 11. ISL32614E AND ISL32611E PERFORMANCE WITH VCC = 1.8V, 256kbps, 1000’ (305m) CAT 5 CABLE DRIVER INPUT (V) TA = +25°C; Unless Otherwise Specified (Continued) 5 0 RECEIVER OUTPUT (V) RECEIVER INPUTS (V) Typical Performance Curves DI 4 3 2 1 0 A-B -1 -2 -3 -4 RD = ∞ 4 2 0 TIME (4µs/DIV) FIGURE 12. ISL32614E AND ISL32611E PERFORMANCE WITH VCC = 3.3V, 500kbps, 2000’ (610m) CAT 5 CABLE Die Characteristics SUBSTRATE POTENTIAL (POWERED UP) : GND PROCESS: Si Gate BiCMOS 9 FN7869.0 October 21, 2011 ISL32610E, ISL32611E, ISL32612E Revision History The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to web to make sure you have the latest revision. DATE 10/21/2011 REVISION CHANGE FN7869.0 Initial Release Products Intersil Corporation is a leader in the design and manufacture of high-performance analog semiconductors. The Company's products address some of the industry's fastest growing markets, such as, flat panel displays, cell phones, handheld products, and notebooks. Intersil's product families address power management and analog signal processing functions. Go to www.intersil.com/products for a complete list of Intersil product families. For a complete listing of Applications, Related Documentation and Related Parts, please see the respective device information page on intersil.com: ISL32610E, ISL32611E, ISL32612E To report errors or suggestions for this datasheet, please go to: www.intersil.com/askourstaff FITs are available from our website at: http://rel.intersil.com/reports/search.php For additional products, see www.intersil.com/product_tree Intersil products are manufactured, assembled and tested utilizing ISO9000 quality systems as noted in the quality certifications found at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 10 FN7869.0 October 21, 2011 ISL32610E, ISL32611E, ISL32612E Package Outline Drawing P5.064 5 LEAD SMALL OUTLINE TRANSISTOR PLASTIC PACKAGE Rev 3, 4/11 8° 0° 3.00 3 2.80 (1.90) 5 0.22 0.08 5 4 3.00 2.60 1.70 1.50 3 2 (0.95) SEE DETAIL X 0.50 0.30 0.20 (0.008) M C TOP VIEW END VIEW 0.25 0.10 0.10 MIN 1.30 0.90 1.45 SEATING 0.90 PLANE C GAUGE PLANE SEATING PLANE 4 0.55 0.35 C 0.15 0.00 0.10 (0.004) C (0.60) SIDE VIEW 8° 0° (0.25) DETAIL "X" 5x (0.60) 5x (1.2) 5 4 (2.4) NOTES: 1. Dimensioning and tolerance per ASME Y14.5M-1994. 3 2. Package conforms to EIAJ SC-74 and JEDEC MO178AA. 3. Package length and width are exclusive of mold flash, protrusions, or gate burrs. 4. Footlength measured at reference to gauge plane. 5. Lead thickness applies to the flat section of the lead between 0.08mm and 0.15mm from the lead tip. (2x 0.95) 6. Controlling dimension: MILLIMETER. Dimensions in ( ) for reference only. (1.90) TYPICAL RECOMMENDED LAND PATTERN 11 FN7869.0 October 21, 2011 ISL32610E, ISL32611E, ISL32612E Package Outline Drawing P6.064 6 LEAD SMALL OUTLINE TRANSISTOR PLASTIC PACKAGE Rev 4, 2/10 0-8° 1.90 0.95 0.08-0.22 D A 6 5 4 2.80 PIN 1 INDEX AREA 3 1.60 +0.15/-0.10 3 (0.60) 1 2 3 0.20 C 2x 0.40 ±0.10 B SEE DETAIL X 3 0.20 M C A-B D END VIEW TOP VIEW 10° TYP (2 PLCS) 2.90 ±0.10 3 1.15 +0.15/-0.25 C 0.10 C SEATING PLANE 0.00-0.15 SIDE VIEW (0.25) GAUGE PLANE 1.45 MAX DETAIL "X" 0.45±0.1 4 (0.95) (0.60) (1.20) (2.40) NOTES: 1. Dimensions are in millimeters. Dimensions in ( ) for Reference Only. 2. Dimensioning and tolerancing conform to ASME Y14.5M-1994. 3. Dimension is exclusive of mold flash, protrusions or gate burrs. 4. Foot length is measured at reference to guage plane. 5. Package conforms to JEDEC MO-178AB. TYPICAL RECOMMENDED LAND PATTERN 12 FN7869.0 October 21, 2011