LM2931-N www.ti.com SNOSBE5G – MARCH 2000 – REVISED APRIL 2013 LM2931-N Series Low Dropout Regulators Check for Samples: LM2931-N FEATURES DESCRIPTION • • • • • • • • • • The LM2931-N positive voltage regulator features a very low quiescent current of 1mA or less when supplying 10mA loads. This unique characteristic and the extremely low input-output differential required for proper regulation (0.2V for output currents of 10mA) make the LM2931-N the ideal regulator for standby power systems. Applications include memory standby circuits, CMOS and other low power processor power supplies as well as systems demanding as much as 100mA of output current. 1 2 • Very Low Quiescent Current Output Current in Excess of 100 mA Input-output Differential Less than 0.6V Reverse Battery Protection 60V Load Dump Protection −50V Reverse Transient Protection Short Circuit Protection Internal Thermal Overload Protection Mirror-image Insertion Protection Available in TO-220, TO-92, TO-263, or SOIC-8 Packages Available as Adjustable with TTL Compatible Switch Designed originally for automotive applications, the LM2931-N and all regulated circuitry are protected from reverse battery installations or 2 battery jumps. During line transients, such as a load dump (60V) when the input voltage to the regulator can momentarily exceed the specified maximum operating voltage, the regulator will automatically shut down to protect both internal circuits and the load. The LM2931-N cannot be harmed by temporary mirror-image insertion. Familiar regulator features such as short circuit and thermal overload protection are also provided. The LM2931-N family includes a fixed 5V output (±3.8% tolerance for A grade) or an adjustable output with ON/OFF pin. Both versions are available in a TO-220 power package, DDPAK/TO-263 surface mount package, and an 8-lead SOIC package. The fixed output version is also available in the TO-92 plastic package. Connection Diagrams FIXED VOLTAGE OUTPUT Figure 1. TO-220 3-Lead Power Package Front View Figure 2. DDPAK/TO-263 Surface-Mount Package Top View Figure 3. Side View 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2000–2013, Texas Instruments Incorporated LM2931-N SNOSBE5G – MARCH 2000 – REVISED APRIL 2013 www.ti.com *NC = Not internally connected. Must be electrically isolated from the rest of the circuit for the DSBGA package. Figure 4. 8-Pin SOIC Top View Figure 5. TO-92 Plastic Package Bottom View Figure 6. 6-Bump DSBGA Top View (Bump Side Down) Figure 7. DSBGA Laser Mark ADJUSTABLE OUTPUT VOLTAGE Figure 8. TO-220 5-Lead Power Package Front View Figure 9. DDPAK/TO-263 5-Lead Surface-Mount Package Top View 2 Submit Documentation Feedback Figure 10. Side View Copyright © 2000–2013, Texas Instruments Incorporated Product Folder Links: LM2931-N LM2931-N www.ti.com SNOSBE5G – MARCH 2000 – REVISED APRIL 2013 Figure 11. 8-Pin SOIC Top View Typical Applications *Required if regulator is located far from power supply filter. **C2 must be at least 100 μF to maintain stability. May be increased without bound to maintain regulation during transients. Locate as close as possible to the regulator. This capacitor must be rated over the same operating temperature range as the regulator. The equivalent series resistance (ESR) of this capacitor is critical; see curve. Figure 12. LM2931-N Fixed Output Note: Using 27k for R1 will automatically compensate for errors in VOUT due to the input bias current of the ADJ pin (approximately 1 μA). Figure 13. LM2931-N Adjustable Output Submit Documentation Feedback Copyright © 2000–2013, Texas Instruments Incorporated Product Folder Links: LM2931-N 3 LM2931-N SNOSBE5G – MARCH 2000 – REVISED APRIL 2013 www.ti.com These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. ABSOLUTE MAXIMUM RATINGS (1) (2) Input Voltage Operating Range 26V Overvoltage Protection LM2931A, LM2931C (Adjustable) 60V LM2931-N 50V Internal Power Dissipation (3) (4) Internally Limited Operating Ambient Temperature −40°C to +85°C Range Maximum Junction Temperature 125°C −65°C to +150°C Storage Temperature Range Lead Temp. (Soldering, 10 seconds) ESD Tolerance (1) (2) (3) (4) (5) 230°C (5) 2000V Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Electrical specifications do not apply when operating the device beyond its rated operating conditions. If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and specifications. See circuit in Typical Applications. To ensure constant junction temperature, low duty cycle pulse testing is used. The maximum power dissipation is a function of maximum junction temperature TJmax, total thermal resistance θJA, and ambient temperature TA. The maximum allowable power dissipation at any ambient temperature is PD = (TJmax − TA)/θJA. If this dissipation is exceeded, the die temperature will rise above 150°C and the LM2931-N will go into thermal shutdown. For the LM2931-N in the TO-92 package, θJA is 195°C/W; in the SOIC-8 package, θJA is 160°C/W, and in the TO-220 package, θJA is 50°C/W; in the DDPAK/TO-263 package, θJA is 73°C/W; and in the 6-Bump DSBGA package θJA is 290°C/W. If the TO-220 package is used with a heat sink, θJA is the sum of the package thermal resistance junction-to-case of 3°C/W and the thermal resistance added by the heat sink and thermal interface.If the TO-263 package is used, the thermal resistance can be reduced by increasing the P.C. board copper area thermally connected to the package: Using 0.5 square inches of copper area, θJA is 50°C/W; with 1 square inch of copper area, θJA is 37°C/W; and with 1.6 or more square inches of copper area, θJA is 32°C/W. Human body model, 100 pF discharged through 1.5 kΩ. ELECTRICAL CHARACTERISTICS FOR FIXED 3.3V VERSION VIN = 14V, IO = 10mA, TJ = 25°C, C2 = 100μF (unless otherwise specified) (1) LM2931-N-3.3 Parameter Conditions Output Voltage Typ 3.3 4V ≤ VIN ≤ 26V, IO = 100 mA −40°C ≤ TJ ≤ 125°C Limit Units 3.465 3.135 VMAX VMIN 3.630 2.970 VMAX VMIN (2) Line Regulation 4V ≤ VIN ≤ 26V 4 33 mVMAX Load Regulation 5mA ≤ IO ≤ 100mA 10 50 mVMAX Output Impedance 100mADC and 10mArms, 100Hz - 10kHz 200 Quiescent Current IO ≤ 10mA, 4V ≤ VIN ≤ 26V 0.4 mΩ 1.0 mAMAX −40°C ≤ TJ ≤ 125°C Output Noise Voltage IO = 100mA, VIN = 14V, TJ = 25°C 15 10Hz -100kHz, COUT = 100μF 330 μVrms 13 mV/1000 hr 80 dB Long Term Stability Ripple Rejection (1) (2) 4 fO = 120Hz mA See circuit in Typical Applications. To ensure constant junction temperature, low duty cycle pulse testing is used. All limits are specified for TJ = 25°C (standard type face) or over the full operating junction temperature range of −40°C to +125°C (bold type face). Submit Documentation Feedback Copyright © 2000–2013, Texas Instruments Incorporated Product Folder Links: LM2931-N LM2931-N www.ti.com SNOSBE5G – MARCH 2000 – REVISED APRIL 2013 ELECTRICAL CHARACTERISTICS FOR FIXED 3.3V VERSION (continued) VIN = 14V, IO = 10mA, TJ = 25°C, C2 = 100μF (unless otherwise specified) (1) LM2931-N-3.3 Parameter Conditions Dropout Voltage Limit Units 0.05 0.30 0.2 0.6 VMAX Typ IO = 10mA IO = 100mA Maximum Operational Input Voltage (2) 33 26 VMIN Maximum Line Transient RL = 500Ω, VO ≤ 5.5V, T = 1ms, τ ≤ 100ms 70 50 VMIN Reverse Polarity Input Voltage, DC VO ≥ −0.3V, RL = 500Ω −30 −15 VMIN Reverse Polarity Input Voltage, Transient T = 1ms, τ ≤ 100ms, RL = 500Ω −80 −50 VMIN ELECTRICAL CHARACTERISTICS FOR FIXED 5V VERSION VIN = 14V, IO = 10mA, TJ = 25°C, C2 = 100 μF (unless otherwise specified) (1) LM2931A-5.0 Parameter Conditions Output Voltage Typ 5 6.0V ≤ VIN ≤ 26V, IO = 100mA −40°C ≤ TJ ≤ 125°C Line Regulation 9V ≤ VIN ≤ 16V 6V ≤ VIN ≤ 26V Load Regulation Output Impedance Quiescent Current LM2931-N-5.0 Limit Limit Units 5.25 4.75 VMAX VMIN 5.5 4.5 VMAX VMIN 2 4 10 30 mVMAX 14 50 mVMAX (2) Typ 5.19 4.81 5 5.25 4.75 (2) 2 4 10 30 5 mA ≤ IO ≤ 100mA 14 50 100mADC and 10mArms, 100Hz -10kHz 200 IO ≤ 10mA, 6V ≤ VIN ≤ 26V 0.4 1.0 IO = 100mA, VIN = 14V, TJ = 25°C 15 30 10Hz -100kHz, COUT = 100μF 500 500 μVrms 20 20 mV/1000 hr 200 0.4 mΩ 1.0 mAMAX −40°C ≤ TJ ≤ 125°C Output Noise Voltage Long Term Stability 15 mAMAX Ripple Rejection fO = 120 Hz 80 55 80 Dropout Voltage IO = 10mA IO = 100mA 0.05 0.3 0.2 0.6 0.05 0.3 0.2 0.6 VMAX 33 26 33 26 VMIN Maximum Operational Input Voltage dBMIN Maximum Line Transient RL = 500Ω, VO ≤ 5.5V, T = 1ms, τ ≤ 100ms 70 60 70 50 VMIN Reverse Polarity Input Voltage, DC VO ≥ −0.3V, RL = 500Ω −30 −15 −30 −15 VMIN Reverse Polarity Input Voltage, Transient T = 1ms, τ ≤ 100ms, RL = 500Ω −80 −50 −80 −50 VMIN (1) (2) See circuit in Typical Applications. To ensure constant junction temperature, low duty cycle pulse testing is used. All limits are specified for TJ = 25°C (standard type face) or over the full operating junction temperature range of −40°C to +125°C (bold type face). Submit Documentation Feedback Copyright © 2000–2013, Texas Instruments Incorporated Product Folder Links: LM2931-N 5 LM2931-N SNOSBE5G – MARCH 2000 – REVISED APRIL 2013 www.ti.com ELECTRICAL CHARACTERISTICS FOR ADJUSTABLE VERSION VIN = 14V, VOUT = 3V, IO = 10 mA, TJ = 25°C, R1 = 27k, C2 = 100 μF (unless otherwise specified) Parameter Conditions Reference Voltage (1) Typ Limit Units Limit 1.20 1.26 VMAX 1.14 VMIN IO ≤ 100 mA, −40°C ≤ Tj ≤ 125°C, R1 = 27k 1.32 VMAX Measured from VOUT to Adjust Pin 1.08 VMIN 24 VMAX Output Voltage Range 3 VMIN mV/VMAX Line Regulation VOUT + 0.6V ≤ VIN ≤ 26V 0.2 1.5 Load Regulation 5 mA ≤ IO ≤ 100 mA 0.3 1 Output Impedance 100 mADC and 10 mArms, 100 Hz–10 kHz 40 Quiescent Current IO = 10 mA 0.4 Output Noise Voltage %MAX mΩ/V 1 mAMAX 1 mAMAX IO = 100 mA 15 During Shutdown RL = 500Ω 0.8 10 Hz–100 kHz 100 μVrms/V 0.4 %/1000 hr Long Term Stability mA Ripple Rejection fO = 120 Hz 0.02 Dropout Voltage IO ≤ 10 mA 0.05 0.2 VMAX %/V IO = 100 mA 0.3 0.6 VMAX 33 26 VMIN 70 60 VMIN −30 −15 VMIN −80 −50 VMIN On 2.0 1.2 VMAX Off 2.2 3.25 VMIN 20 50 μAMAX Maximum Operational Input Voltage Maximum Line Transient IO = 10 mA, Reference Voltage ≤ 1.5V T = 1 ms, τ ≤ 100 ms Reverse Polarity Input VO ≥ −0.3V, RL = 500Ω Voltage, DC Reverse Polarity Input T = 1 ms, τ ≤ 100 ms, RL = 500Ω Voltage, Transient On/Off Threshold Voltage VO=3V On/Off Threshold Current (1) 6 See circuit in Typical Applications. To ensure constant junction temperature, low duty cycle pulse testing is used. Submit Documentation Feedback Copyright © 2000–2013, Texas Instruments Incorporated Product Folder Links: LM2931-N LM2931-N www.ti.com SNOSBE5G – MARCH 2000 – REVISED APRIL 2013 TYPICAL PERFORMANCE CHARACTERISTICS Dropout Voltage Dropout Voltage Figure 14. Figure 15. Low Voltage Behavior Output at Voltage Extremes Figure 16. Figure 17. Line Transient Response Load Transient Response Figure 18. Figure 19. Submit Documentation Feedback Copyright © 2000–2013, Texas Instruments Incorporated Product Folder Links: LM2931-N 7 LM2931-N SNOSBE5G – MARCH 2000 – REVISED APRIL 2013 www.ti.com TYPICAL PERFORMANCE CHARACTERISTICS (continued) 8 Peak Output Current Quiescent Current Figure 20. Figure 21. Quiescent Current Quiescent Current Figure 22. Figure 23. Ripple Rejection Ripple Rejection Figure 24. Figure 25. Submit Documentation Feedback Copyright © 2000–2013, Texas Instruments Incorporated Product Folder Links: LM2931-N LM2931-N www.ti.com SNOSBE5G – MARCH 2000 – REVISED APRIL 2013 TYPICAL PERFORMANCE CHARACTERISTICS (continued) Output Impedance Operation During Load Dump Figure 26. Figure 27. Reference Voltage Maximum Power Dissipation (SOIC-8) Figure 28. Figure 29. Maximum Power Dissipation (TO-220) Maximum Power Dissipation (TO-92) Figure 30. Figure 31. Submit Documentation Feedback Copyright © 2000–2013, Texas Instruments Incorporated Product Folder Links: LM2931-N 9 LM2931-N SNOSBE5G – MARCH 2000 – REVISED APRIL 2013 www.ti.com TYPICAL PERFORMANCE CHARACTERISTICS (continued) Maximum Power Dissipation (TO-263) (1) On/Off Threshold Figure 32. Figure 33. Output Capacitor ESR Figure 34. (1) 10 The maximum power dissipation is a function of maximum junction temperature TJmax, total thermal resistance θJA, and ambient temperature TA. The maximum allowable power dissipation at any ambient temperature is PD = (TJmax − TA)/θJA. If this dissipation is exceeded, the die temperature will rise above 150°C and the LM2931-N will go into thermal shutdown. For the LM2931-N in the TO-92 package, θJA is 195°C/W; in the SOIC-8 package, θJA is 160°C/W, and in the TO-220 package, θJA is 50°C/W; in the DDPAK/TO-263 package, θJA is 73°C/W; and in the 6-Bump DSBGA package θJA is 290°C/W. If the TO-220 package is used with a heat sink, θJA is the sum of the package thermal resistance junction-to-case of 3°C/W and the thermal resistance added by the heat sink and thermal interface.If the TO-263 package is used, the thermal resistance can be reduced by increasing the P.C. board copper area thermally connected to the package: Using 0.5 square inches of copper area, θJA is 50°C/W; with 1 square inch of copper area, θJA is 37°C/W; and with 1.6 or more square inches of copper area, θJA is 32°C/W. Submit Documentation Feedback Copyright © 2000–2013, Texas Instruments Incorporated Product Folder Links: LM2931-N LM2931-N www.ti.com SNOSBE5G – MARCH 2000 – REVISED APRIL 2013 SCHEMATIC DIAGRAM Submit Documentation Feedback Copyright © 2000–2013, Texas Instruments Incorporated Product Folder Links: LM2931-N 11 LM2931-N SNOSBE5G – MARCH 2000 – REVISED APRIL 2013 www.ti.com APPLICATION HINTS One of the distinguishing factors of the LM2931-N series regulators is the requirement of an output capacitor for device stability. The value required varies greatly depending upon the application circuit and other factors. Thus some comments on the characteristics of both capacitors and the regulator are in order. High frequency characteristics of electrolytic capacitors depend greatly on the type and even the manufacturer. As a result, a value of capacitance that works well with the LM2931-N for one brand or type may not necessary be sufficient with an electrolytic of different origin. Sometimes actual bench testing, as described later, will be the only means to determine the proper capacitor type and value. Experience has shown that, as a rule of thumb, the more expensive and higher quality electrolytics generally allow a smaller value for regulator stability. As an example, while a high-quality 100 μF aluminum electrolytic covers all general application circuits, similar stability can be obtained with a tantalum electrolytic of only 47μF. This factor of two can generally be applied to any special application circuit also. Another critical characteristic of electrolytics is their performance over temperature. While the LM2931-N is designed to operate to −40°C, the same is not always true with all electrolytics (hot is generally not a problem). The electrolyte in many aluminum types will freeze around −30°C, reducing their effective value to zero. Since the capacitance is needed for regulator stability, the natural result is oscillation (and lots of it) at the regulator output. For all application circuits where cold operation is necessary, the output capacitor must be rated to operate at the minimum temperature. By coincidence, worst-case stability for the LM2931-N also occurs at minimum temperatures. As a result, in applications where the regulator junction temperature will never be less than 25°C, the output capacitor can be reduced approximately by a factor of two over the value needed for the entire temperature range. To continue our example with the tantalum electrolytic, a value of only 22μF would probably thus suffice. For high-quality aluminum, 47μF would be adequate in such an application. Another regulator characteristic that is noteworthy is that stability decreases with higher output currents. This sensible fact has important connotations. In many applications, the LM2931-N is operated at only a few milliamps of output current or less. In such a circuit, the output capacitor can be further reduced in value. As a rough estimation, a circuit that is required to deliver a maximum of 10mA of output current from the regulator would need an output capacitor of only half the value compared to the same regulator required to deliver the full output current of 100mA. If the example of the tantalum capacitor in the circuit rated at 25°C junction temperature and above were continued to include a maximum of 10mA of output current, then the 22μF output capacitor could be reduced to only 10μF. In the case of the LM2931CT adjustable regulator, the minimum value of output capacitance is a function of the output voltage. As a general rule, the value decreases with higher output voltages, since internal loop gain is reduced. At this point, the procedure for bench testing the minimum value of an output capacitor in a special application circuit should be clear. Since worst-case occurs at minimum operating temperatures and maximum operating currents, the entire circuit, including the electrolytic, should be cooled to the minimum temperature. The input voltage to the regulator should be maintained at 0.6V above the output to keep internal power dissipation and die heating to a minimum. Worst-case occurs just after input power is applied and before the die has had a chance to heat up. Once the minimum value of capacitance has been found for the brand and type of electrolytic in question, the value should be doubled for actual use to account for production variations both in the capacitor and the regulator. (All the values in this section and the remainder of the data sheet were determined in this fashion.) LM2931-N DSBGA Light Sensitivity When the LM2931-N DSBGA package is exposed to bright sunlight, normal office fluorescent light, and other LED's, it operates within the limits specified in the electrical characteristic table. 12 Submit Documentation Feedback Copyright © 2000–2013, Texas Instruments Incorporated Product Folder Links: LM2931-N LM2931-N www.ti.com SNOSBE5G – MARCH 2000 – REVISED APRIL 2013 Definition of Terms Dropout Voltage: The input-output voltage differential at which the circuit ceases to regulate against further reduction in input voltage. Measured when the output voltage has dropped 100 mV from the nominal value obtained at 14V input, dropout voltage is dependent upon load current and junction temperature. Input Voltage: The DC voltage applied to the input terminals with respect to ground. Input-Output Differential: The voltage difference between the unregulated input voltage and the regulated output voltage for which the regulator will operate. Line Regulation: The change in output voltage for a change in the input voltage. The measurement is made under conditions of low dissipation or by using pulse techniques such that the average chip temperature is not significantly affected. Load Regulation: The change in output voltage for a change in load current at constant chip temperature. Long Term Stability: Output voltage stability under accelerated life-test conditions after 1000 hours with maximum rated voltage and junction temperature. Output Noise Voltage: The rms AC voltage at the output, with constant load and no input ripple, measured over a specified frequency range. Quiescent Current: That part of the positive input current that does not contribute to the positive load current. The regulator ground lead current. Ripple Rejection: The ratio of the peak-to-peak input ripple voltage to the peak-to-peak output ripple voltage at a specified frequency. Temperature Stability of VO: The percentage change in output voltage for a thermal variation from room temperature to either temperature extreme. Submit Documentation Feedback Copyright © 2000–2013, Texas Instruments Incorporated Product Folder Links: LM2931-N 13 LM2931-N SNOSBE5G – MARCH 2000 – REVISED APRIL 2013 www.ti.com REVISION HISTORY Changes from Revision F (April 2013) to Revision G • 14 Page Changed layout of National Data Sheet to TI format .......................................................................................................... 13 Submit Documentation Feedback Copyright © 2000–2013, Texas Instruments Incorporated Product Folder Links: LM2931-N PACKAGE OPTION ADDENDUM www.ti.com 21-May-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (°C) Device Marking (3) (4/5) LM2931AM-5.0 ACTIVE SOIC D 8 95 TBD Call TI Call TI -40 to 85 2931A M-5.0 LM2931AM-5.0/NOPB ACTIVE SOIC D 8 95 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 2931A M-5.0 LM2931AMX-5.0 ACTIVE SOIC D 8 2500 TBD Call TI Call TI -40 to 85 2931A M-5.0 LM2931AMX-5.0/NOPB ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 2931A M-5.0 LM2931AS-5.0 ACTIVE DDPAK/ TO-263 KTT 3 45 TBD Call TI Call TI -40 to 85 LM2931 AS5.0 LM2931AS-5.0/NOPB ACTIVE DDPAK/ TO-263 KTT 3 45 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR -40 to 85 LM2931 AS5.0 LM2931ASX-5.0 ACTIVE DDPAK/ TO-263 KTT 3 500 TBD Call TI Call TI -40 to 85 LM2931 AS5.0 LM2931ASX-5.0/NOPB ACTIVE DDPAK/ TO-263 KTT 3 500 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR -40 to 85 LM2931 AS5.0 LM2931AT-5.0 ACTIVE TO-220 NDE 3 45 TBD Call TI Call TI -40 to 85 LM2931 AT5.0 LM2931AT-5.0/NOPB ACTIVE TO-220 NDE 3 45 Green (RoHS & no Sb/Br) CU SN Level-1-NA-UNLIM -40 to 85 LM2931 AT5.0 LM2931AZ-5.0/LFT1 ACTIVE TO-92 LP 3 2000 Green (RoHS & no Sb/Br) SN Level-1-NA-UNLIM LM293 1AZ-5 LM2931AZ-5.0/LFT3 ACTIVE TO-92 LP 3 2000 Green (RoHS & no Sb/Br) SNCU Level-1-NA-UNLIM LM293 1AZ-5 LM2931AZ-5.0/LFT4 ACTIVE TO-92 LP 3 2000 Green (RoHS & no Sb/Br) SNCU Level-1-NA-UNLIM LM293 1AZ-5 LM2931AZ-5.0/NOPB ACTIVE TO-92 LP 3 1800 Green (RoHS & no Sb/Br) SNCU Level-1-NA-UNLIM -40 to 85 LM293 1AZ-5 LM2931CM ACTIVE SOIC D 8 95 TBD Call TI Call TI -40 to 85 LM29 31CM LM2931CM/NOPB ACTIVE SOIC D 8 95 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 LM29 31CM LM2931CMX ACTIVE SOIC D 8 2500 TBD Call TI Call TI -40 to 85 LM29 31CM Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 21-May-2013 Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (°C) Device Marking (3) (4/5) LM2931CMX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 LM29 31CM LM2931CS ACTIVE DDPAK/ TO-263 KTT 5 45 TBD Call TI Call TI -40 to 85 LM2931CS LM2931CS/NOPB ACTIVE DDPAK/ TO-263 KTT 5 45 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR -40 to 85 LM2931CS LM2931CT ACTIVE TO-220 KC 5 45 TBD Call TI Call TI -40 to 85 LM2931CT LM2931CT/LF03 ACTIVE TO-220 NDH 5 45 Green (RoHS & no Sb/Br) CU SN Level-1-NA-UNLIM LM2931CT LM2931CT/LF04 ACTIVE TO-220 NEB 5 45 Green (RoHS & no Sb/Br) CU SN Level-1-NA-UNLIM LM2931CT LM2931CT/NOPB ACTIVE TO-220 KC 5 45 Green (RoHS & no Sb/Br) CU SN Level-1-NA-UNLIM -40 to 85 LM2931CT LM2931M-5.0 ACTIVE SOIC D 8 95 TBD Call TI Call TI -40 to 85 2931 M-5.0 LM2931M-5.0/NOPB ACTIVE SOIC D 8 95 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 2931 M-5.0 LM2931MX-5.0 ACTIVE SOIC D 8 2500 TBD Call TI Call TI -40 to 85 2931 M-5.0 LM2931MX-5.0/NOPB ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 2931 M-5.0 LM2931S-5.0 ACTIVE DDPAK/ TO-263 KTT 3 45 TBD Call TI Call TI -40 to 85 LM2931S 5.0 LM2931S-5.0/NOPB ACTIVE DDPAK/ TO-263 KTT 3 45 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR -40 to 85 LM2931S 5.0 LM2931T-5.0 ACTIVE TO-220 NDE 3 45 TBD Call TI Call TI -40 to 85 LM2931T 5.0 LM2931T-5.0/NOPB ACTIVE TO-220 NDE 3 45 Green (RoHS & no Sb/Br) CU SN Level-1-NA-UNLIM -40 to 85 LM2931T 5.0 LM2931Z-5.0/LFT1 ACTIVE TO-92 LP 3 2000 Green (RoHS & no Sb/Br) SN Level-1-NA-UNLIM LM293 1Z-5 LM2931Z-5.0/LFT2 ACTIVE TO-92 LP 3 2000 Green (RoHS & no Sb/Br) SN Level-1-NA-UNLIM LM293 1Z-5 LM2931Z-5.0/NOPB ACTIVE TO-92 LP 3 1800 Green (RoHS & no Sb/Br) SNCU Level-1-NA-UNLIM Addendum-Page 2 -40 to 85 LM293 1Z-5 Samples PACKAGE OPTION ADDENDUM www.ti.com 21-May-2013 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 3 PACKAGE MATERIALS INFORMATION www.ti.com 8-Apr-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device LM2931AMX-5.0 Package Package Pins Type Drawing SOIC SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) D 8 2500 330.0 12.4 6.5 B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 5.4 2.0 8.0 12.0 Q1 LM2931AMX-5.0/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1 LM2931ASX-5.0 DDPAK/ TO-263 KTT 3 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2 LM2931ASX-5.0/NOPB DDPAK/ TO-263 KTT 3 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2 LM2931CMX SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1 LM2931CMX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1 LM2931MX-5.0 SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1 LM2931MX-5.0/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 8-Apr-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM2931AMX-5.0 SOIC D 8 2500 367.0 367.0 35.0 LM2931AMX-5.0/NOPB SOIC D 8 2500 367.0 367.0 35.0 LM2931ASX-5.0 DDPAK/TO-263 KTT 3 500 367.0 367.0 45.0 LM2931ASX-5.0/NOPB DDPAK/TO-263 KTT 3 500 367.0 367.0 45.0 LM2931CMX SOIC D 8 2500 367.0 367.0 35.0 LM2931CMX/NOPB SOIC D 8 2500 367.0 367.0 35.0 LM2931MX-5.0 SOIC D 8 2500 367.0 367.0 35.0 LM2931MX-5.0/NOPB SOIC D 8 2500 367.0 367.0 35.0 Pack Materials-Page 2 MECHANICAL DATA NDH0005D www.ti.com MECHANICAL DATA NDE0003B www.ti.com MECHANICAL DATA KTT0003B TS3B (Rev F) BOTTOM SIDE OF PACKAGE www.ti.com MECHANICAL DATA KTT0005B TS5B (Rev D) BOTTOM SIDE OF PACKAGE www.ti.com MECHANICAL DATA NEB0005F www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2013, Texas Instruments Incorporated