LM4880 www.ti.com SNAS103C – NOVEMBER 1995 – REVISED MAY 2013 LM4880 Dual 250 mW Audio Power Amplifier with Shutdown Mode Check for Samples: LM4880 FEATURES DESCRIPTION • The LM4880 is a dual audio power amplifier capable of delivering typically 250mW per channel of continuous average power to an 8Ω load with 0.1% THD+N using a 5V power supply. 1 2 • • • No Bootstrap Capacitors or Snubber Circuits are Necessary Small Outline (SOIC) and PDIP Packaging Unity-Gain Stable External Gain Configuration Capability APPLICATIONS Boomer audio power amplifiers were designed specifically to provide high quality output power with a minimal amount of external components using surface mount packaging. • • • Headphone Amplifier Personal Computers CD-ROM Players Since the LM4880 does not require bootstrap capacitors or snubber networks, it is optimally suited for low-power portable systems. KEY SPECIFICATIONS The LM4880 features an externally controlled, lowpower consumption shutdown mode, as well as an internal thermal shutdown protection mechanism. • • • • • THD+N at 1kHz at 200mW Continuous Average Output Power into 8Ω: 0.1% (max) THD+N at 1kHz at 85mW Continuous Average Output Power into 32Ω: 0.1% (typ) Output Power at 10% THD+N at 1kHz into 8Ω 325 mW (typ) Shutdown Current 0.7 µA (typ) 2.7V to 5.5V Supply Voltage Range The unity-gain stable LM4880 can be configured by external gain-setting resistors. Connection Diagram Figure 1. Small Outline and PDIP Packages- Top View See Package Number D0008A for SOIC or Package Number P0008E for PDIP 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 1995–2013, Texas Instruments Incorporated LM4880 SNAS103C – NOVEMBER 1995 – REVISED MAY 2013 www.ti.com Typical Application *Refer to Application Information for information concerning proper selection of the input and output coupling capacitors. Figure 2. Typical Audio Amplifier Application Circuit These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. Absolute Maximum Ratings (1) (2) Supply Voltage 6.0V −65°C to +150°C Storage Temperature −0.3V to VDD + 0.3V Input Voltage Power Dissipation (3) Internally limited ESD Susceptibility (4) 2000V ESD Susceptibility (5) 200V Junction Temperature Soldering Information 150°C Small Outline Package Vapor Phase (60 sec.) Infrared (15 sec.) Thermal Resistance (1) (2) (3) (4) (5) 2 215°C 220°C θJC (PDIP) 37°C/W θJA (PDIP) 107°C/W θJC (SOIC) 35°C/W θJA (SOIC) 170°C/W Absolute Maximum Ratings indicate limits beyond which damage may occur. Operating Ratings indicate conditions for which the device is functional, but do not specify specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not specified for parameters where no limit is given, however, the typical value is a good indication of device performance. If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and specifications. The maximum power dissipation must be derated at elevated temperatures and is dictated by TJMAX, θJA, and the ambient temperature TA. The maximum allowable power dissipation is PDMAX = (TJMAX − TA)/θJA or the number given in the Absolute Maximum Ratings, whichever is lower. For the LM4880, TJMAX = 150°C, and the typical junction-to-ambient thermal resistance is 170°C/W for package D0008A and 107°C/W for package P0008E. Human body model, 100 pF discharged through a 1.5 kΩ resistor. Machine model, 220 pF–240 pF discharged through all pins. Submit Documentation Feedback Copyright © 1995–2013, Texas Instruments Incorporated Product Folder Links: LM4880 LM4880 www.ti.com SNAS103C – NOVEMBER 1995 – REVISED MAY 2013 Operating Ratings TMIN≤TA≤TMAX Temperature Range −40°C≤TA≤+85°C 2.7V≤VDD≤5.5V Supply Voltage Electrical Characteristics (1) (2) The following specifications apply for VDD = 5V unless otherwise specified. Limits apply for TA = 25°C. Symbol Parameter Conditions LM4880 Typical (3) Limit Units (Limits) (4) VDD Supply Voltage 2.7 V (min) 5.5 V (max) IDD Quiescent Power Supply Current VIN=0V, IO=0A 3.6 6.0 mA (max) ISD Shutdown Current VPIN5=VDD 0.7 5 μA (max) VOS Output Offset Voltage VIN=0V 5 50 mV (max) PO Output Power THD=0.1% (max); f=1 kHz; RL=8Ω 250 200 mW (min) RL=32Ω 85 mW RL=8Ω 325 mW RL=32Ω 110 mW RL=8Ω, PO=200 mW; 0.03 % RL=32Ω, PO=75 mW; 0.02 % 50 dB THD+N=10%; f=1 kHz THD+N Total Harmonic Distortion+Noise f=1 kHz PSRR (1) (2) (3) (4) CB = 1.0 μF, VRIPPLE=200 mVrms, f = 100 Hz Power Supply Rejection Ratio All voltages are measured with respect to the ground pin, unless otherwise specified. Absolute Maximum Ratings indicate limits beyond which damage may occur. Operating Ratings indicate conditions for which the device is functional, but do not specify specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not specified for parameters where no limit is given, however, the typical value is a good indication of device performance. Typicals are measured at 25°C and represent the parametric norm. Limits are ensured to TI's AOQL (Average Outgoing Quality Level). Automatic Shutdown Circuit Figure 3. Automatic Shutdown Circuit Submit Documentation Feedback Copyright © 1995–2013, Texas Instruments Incorporated Product Folder Links: LM4880 3 LM4880 SNAS103C – NOVEMBER 1995 – REVISED MAY 2013 www.ti.com Automatic Switching Circuit Figure 4. Automatic Switching Circuit External Components Description (Figure 2) Components Functional Description 1. Ri Inverting input resistance which sets the closed-loop gain in conjunction with RF. This resistor also forms a high pass filter with Ci at fc = 1/(2πRiCi). 2. Ci Input coupling capacitor which blocks the DC voltage at the amplifier's input terminals. Also creates a high pass filter with Ri at fc = 1/(2πRiCi). Refer to PROPER SELECTION OF EXTERNAL COMPONENTS for an explanation of how to determine the value of Ci. 3. RF Feedback resistance which sets closed-loop gain in conjunction with Ri. 4. CS Supply bypass capacitor which provides power supply filtering. Refer to Application Information for proper placement and selection of the supply bypass capacitor. 5. CB Bypass pin capacitor which provides half-supply filtering. Refer to PROPER SELECTION OF EXTERNAL COMPONENTS for information concerning proper placement and selection of CB. 6. Co Output coupling capacitor which blocks the DC voltage at the amplifier's output. Forms a high pass filter with RL at fo = 1/(2πRLCo). 4 Submit Documentation Feedback Copyright © 1995–2013, Texas Instruments Incorporated Product Folder Links: LM4880 LM4880 www.ti.com SNAS103C – NOVEMBER 1995 – REVISED MAY 2013 Typical Performance Characteristics THD + N vs Output Power THD + N vs Output Power Figure 5. Figure 6. THD + N vs Output Power THD + N vs Output Power Figure 7. Figure 8. THD + N vs Output Power THD + N vs Output Power Figure 9. Figure 10. Submit Documentation Feedback Copyright © 1995–2013, Texas Instruments Incorporated Product Folder Links: LM4880 5 LM4880 SNAS103C – NOVEMBER 1995 – REVISED MAY 2013 www.ti.com Typical Performance Characteristics (continued) 6 THD + N vs Frequency THD + N vs Frequency Figure 11. Figure 12. THD + N vs Frequency THD + N vs Frequency Figure 13. Figure 14. Output Power vs Load Resistance Output Power vs Load Resistance Figure 15. Figure 16. Submit Documentation Feedback Copyright © 1995–2013, Texas Instruments Incorporated Product Folder Links: LM4880 LM4880 www.ti.com SNAS103C – NOVEMBER 1995 – REVISED MAY 2013 Typical Performance Characteristics (continued) Output Power vs Supply Voltage Output Power vs Supply Voltage Figure 17. Figure 18. Output Power vs Supply Voltage Clipping Voltage vs Supply Voltage Figure 19. Figure 20. Clipping Voltage vs Supply Voltage Power Dissipation vs Output Power Figure 21. Figure 22. Submit Documentation Feedback Copyright © 1995–2013, Texas Instruments Incorporated Product Folder Links: LM4880 7 LM4880 SNAS103C – NOVEMBER 1995 – REVISED MAY 2013 www.ti.com Typical Performance Characteristics (continued) 8 Channel Separation Output Attenuation in Shutdown Mode Figure 23. Figure 24. Noise Floor Power Supply Rejection Ratio Figure 25. Figure 26. Open Loop Frequency Response Supply Current vs Supply Voltage Figure 27. Figure 28. Submit Documentation Feedback Copyright © 1995–2013, Texas Instruments Incorporated Product Folder Links: LM4880 LM4880 www.ti.com SNAS103C – NOVEMBER 1995 – REVISED MAY 2013 Typical Performance Characteristics (continued) Frequency Response vs Output Capacitor Size Frequency Response vs Output Capacitor Size Figure 29. Figure 30. Frequency Response vs Input Capacitor Size Typical Application Frequency Response Figure 31. Figure 32. Typical Application Frequency Response Power Derating Curve Figure 33. Figure 34. Submit Documentation Feedback Copyright © 1995–2013, Texas Instruments Incorporated Product Folder Links: LM4880 9 LM4880 SNAS103C – NOVEMBER 1995 – REVISED MAY 2013 www.ti.com APPLICATION INFORMATION SHUTDOWN FUNCTION In order to reduce power consumption while not in use, the LM4880 contains a shutdown pin to externally turn off the amplifier's bias circuitry. This shutdown feature turns the amplifier off when a logic high is placed on the shutdown pin. The trigger point between a logic low and logic high level is typically half supply. It is best to switch between ground and the supply to provide maximum device performance. By switching the shutdown pin to VDD, the LM4880 supply current draw will be minimized in idle mode. While the device will be disabled with shutdown pin voltages less than VDD, the idle current may be greater than the typical value of 0.7 μA. In either case, the shutdown pin should be tied to a definite voltage because leaving the pin floating may result in an unwanted shutdown condition. In many applications, a microcontroller or microprocessor output is used to control the shutdown circuitry which provides a quick, smooth transition into shutdown. Another solution is to use a single-pole, single-throw switch in conjunction with an external pull-up resistor. When the switch is closed, the shutdown pin is connected to ground and enables the amplifier. If the switch is open, then the external pull-up resistor will disable the LM4880. This scheme ensures that the shutdown pin will not float which will prevent unwanted state changes. POWER DISSIPATION Power dissipation is a major concern when using any power amplifier and must be thoroughly understood to ensure a successful design. Equation 1 states the maximum power dissipation point for a single-ended amplifier operating at a given supply voltage and driving a specified output load. PDMAX = (VDD)2/(2π2RL) (1) Since the LM4880 has two operational amplifiers in one package, the maximum internal power dissipation point is twice that of the number which results from Equation 1. Even with the large internal power dissipation, the LM4880 does not require heat sinking over a large range of ambient temperatures. From Equation 1, assuming a 5V power supply and an 8Ω load, the maximum power dissipation point is 158 mW per amplifier. Thus the maximum package dissipation point is 317 mW. The maximum power dissipation point obtained must not be greater than the power dissipation that results from Equation 2: PDMAX = (TJMAX-TA)/θJA (2) For the LM4880 surface mount package, θJA = 170° C/W and TJMAX = 150°C. Depending on the ambient temperature, TA, of the system surroundings, Equation 2 can be used to find the maximum internal power dissipation supported by the IC packaging. If the result of Equation 1 is greater than that of Equation 2, then either the supply voltage must be decreased, the load impedance increased, or the ambient temperature reduced. For the typical application of a 5V power supply, with an 8Ω load, the maximum ambient temperature possible without violating the maximum junction temperature is approximately 96°C provided that device operation is around the maximum power dissipation point. Power dissipation is a function of output power and thus, if typical operation is not around the maximum power dissipation point, the ambient temperature may be increased accordingly. Refer to Typical Performance Characteristics for power dissipation information for lower output powers. POWER SUPPLY BYPASSING As with any power amplifier, proper supply bypassing is critical for low noise performance and high power supply rejection. The capacitor location on both the bypass and power supply pins should be as close to the device as possible. As displayed in Typical Performance Characteristics, the effect of a larger half supply bypass capacitor is improved low frequency PSRR due to increased half-supply stability. Typical applications employ a 5V regulator with 10 μF and a 0.1 μF bypass capacitors which aid in supply stability, but do not eliminate the need for bypassing the supply nodes of the LM4880. The selection of bypass capacitors, especially CB, is thus dependant upon desired low frequency PSRR, click and pop performance as explained in PROPER SELECTION OF EXTERNAL COMPONENTS, system cost, and size constraints. 10 Submit Documentation Feedback Copyright © 1995–2013, Texas Instruments Incorporated Product Folder Links: LM4880 LM4880 www.ti.com SNAS103C – NOVEMBER 1995 – REVISED MAY 2013 AUTOMATIC SHUTDOWN CIRCUIT As shown in Figure 3, the LM4880 can be set up to automatically shutdown when a load is not connected. This circuit is based upon a single control pin common in many headphone jacks. This control pin forms a normally closed switch with one of the output pins. The output of this circuit (the voltage on pin 5 of the LM4880) has two states based on the state of the switch. When the switch is open, signifying that headphones are inserted, the LM4880 should be enabled. When the switch is closed, the LM4880 should be off to minimize power consumption. The operation of this circuit is rather simple. With the switch closed, Rp and Ro form a resistor divider which produces a gate voltage of less than 5 mV. This gate voltage keeps the NMOS inverter off and Rsd pulls the shutdown pin of the LM4880 to the supply voltage. This places the LM4880 in shutdown mode which reduces the supply current to 0.7 μA typically. When the switch is open, the opposite condition is produced. Resistor Rp pulls the gate of the NMOS high which turns on the inverter and produces a logic low signal on the shutdown pin of the LM4880. This state enables the LM4880 and places the amplifier in its normal mode of operation. This type of circuit is clearly valuable in portable products where battery life is critical, but is also beneficial for power conscious designs such as “Green PC's”. AUTOMATIC SWITCHING CIRCUIT A circuit closely related to Automatic Shutdown Circuit is Automatic Switching Circuit. Automatic Switching Circuit utilizes both the input and output of the NMOS inverter to toggle the states of two different audio power amplifiers. The LM4880 is used to drive stereo single ended loads, while the LM4861 drives bridged internal speakers. In this application, the LM4880 and LM4861 are never on at the same time. When the switch inside the headphone jack is open, the LM4880 is enabled and the LM4861 is disabled since the NMOS inverter is on. If a headphone jack is not present, it is assumed that the internal speakers should be on and thus the voltage on the LM4861 shutdown pin is low and the voltage at the LM4880 pin is high. This results in the LM4880 being shutdown and the LM4861 being enabled. Only one channel of this circuit is shown in Figure 4 to keep the drawing simple but the typical application would a LM4880 driving a stereo external headphone jack and two LM4861's driving the internal stereo speakers. If only one internal speaker is required, a single LM4861 can be used as a summer to mix the left and right inputs into a single mono channel. PROPER SELECTION OF EXTERNAL COMPONENTS Selection of external components when using integrated power amplifiers is critical to optimize device and system performance. While the LM4880 is tolerant of external component combinations, care must be exercised when choosing component values. The LM4880 is unity-gain stable which gives a designer maximum system flexibility. The LM4880 should be used in low gain configurations to minimize THD + N values, and maximize the signal to noise ratio. Low gain configurations require large input signals to obtain a given output power. Input signals equal to or greater than 1 Vrms are available from sources such as audio codecs. Please refer to AUDIO POWER AMPLIFIER DESIGN for a more complete explanation of proper gain selection. Besides gain, one of the major design considerations is the closed-loop bandwidth of the amplifier. To a large extent, the bandwidth is dictated by the choice of external components shown in Figure 2. Both the input coupling capacitor, Ci, and the output coupling capacitor, Co, form first order high pass filters which limit low frequency response. These values should be chosen based on needed frequency response for a few distinct reasons. Selection of Input and Output Capacitor Size Large input and output capacitors are both expensive and space hungry for portable designs. Clearly a certain sized capacitor is needed to couple in low frequencies without severe attenuation. But in many cases the transducers used in portable systems, whether internal or external, have little ability to reproduce signals below 100 Hz–150 Hz. Thus using large input and output capacitors may not increase system performance. Submit Documentation Feedback Copyright © 1995–2013, Texas Instruments Incorporated Product Folder Links: LM4880 11 LM4880 SNAS103C – NOVEMBER 1995 – REVISED MAY 2013 www.ti.com In addition to system cost and size, click and pop performance is effected by the size of the input coupling capacitor, Ci. A larger input coupling capacitor requires more charge to reach its quiescent DC voltage (normally 1/2 VDD.) This charge comes from the output via the feedback and is apt to create pops upon device enable. Thus, by minimizing the capacitor size based on necessary low frequency response, turn-on pops can be minimized. Besides minimizing the input and output capacitor sizes, careful consideration should be paid to the bypass capacitor size. The bypass capacitor, CB, is the most critical component to minimize turn-on pops since it determines how fast the LM4880 turns on. The slower the LM4880's outputs ramp to their quiescent DC voltage (nominally 1/2 VDD), the smaller the turn-on pop. Choosing CB equal to 1.0 μF along with a small value of Ci (in the range of 0.1 μF to 0.39 μF), should produce a virtually clickless and popless shutdown function. While the device will function properly, (no oscillations or motorboating), with CB equal to 0.1 μF, the device will be much more susceptible to turn-on clicks and pops. Thus, a value of CB equal to 1.0 μF or larger is recommended in all but the most cost sensitive designs. AUDIO POWER AMPLIFIER DESIGN Design a Dual 200 mW/8Ω Audio Amplifier Given: Power Output: 200 mWrms Load Impedance: 8Ω Input Level: 1 Vrms (max) Input Impedance: 20 kΩ Bandwidth: 100 Hz–20 kHz ± 0.50 dB A designer must first determine the needed supply rail to obtain the specified output power. Calculating the required supply rail involves knowing two parameters, Vopeak and also the dropout voltage. As shown in Typical Performance Characteristics, the dropout voltage is typically 0.5V. Vopeak can be determined from Equation 3. (3) For 200 mW of output power into an 8Ω load, the required Vopeak is 1.79V. Since this is a single supply application, the minimum supply voltage is twice the sum of Vopeak and Vod. Since 5V is a standard supply voltage in most applications, it is chosen for the supply rail. Extra supply voltage creates headroom that allows the LM4880 to reproduce peaks in excess of 200 mW without clipping the signal. At this time, the designer must make sure that the power supply choice along with the output impedance does not violate the conditions explained in POWER DISSIPATION. Remember that the maximum power dissipation value from Equation 1 must be multiplied by two since there are two independent amplifiers inside the package. Once the power dissipation equations have been addressed, the required gain can be determined from Equation 4. (4) (5) AV = −RF/Ri From Equation 4, the minimum gain is: AV = −1.26 Since the desired input impedance was 20 kΩ, and with a gain of −1.26, a value of 27 kΩ is designated for Rf, assuming 5% tolerance resistors. This combination results in a nominal gain of −1.35. The final design step is to address the bandwidth requirements which must be stated as a pair of −3 dB frequency points. Five times away from a −3 dB point is 0.17 dB down from passband response assuming a single pole roll-off. As stated in External Components Description, both Ri in conjunction with Ci, and Co with RL, create first order high pass filters. Thus to obtain the desired frequency low response of 100 Hz within ± 0.5 dB, both poles must be taken into consideration. The combination of two single order filters at the same frequency forms a second order response. This results in a signal which is down 0.34 dB at five times away from the single order filter −3 dB point. Thus, a frequency of 20 Hz is used in the following equations to ensure that the response if better than 0.5 dB down at 100 Hz. Ci ≥ 1/(2π*20kΩ*20Hz) = 0.397 μF; use 0.39 μF 12 Submit Documentation Feedback Copyright © 1995–2013, Texas Instruments Incorporated Product Folder Links: LM4880 LM4880 www.ti.com SNAS103C – NOVEMBER 1995 – REVISED MAY 2013 Co ≥ 1/(2π*8Ω*20Hz) = 995 μF; use 1000 μF The high frequency pole is determined by the product of the desired high frequency pole, fH, and the closed-loop gain, AV. With a closed-loop gain magnitude of 1.35 and fH = 100 kHz, the resulting GBWP = 135 kHz which is much smaller than the LM4880 GBWP of 12.5 MHz. This figure displays that if a designer has a need top design an amplifier with a higher gain, the LM4880 can still be used without running into bandwidth limitations. LM4880 MDA MWA DUAL 250 MW AUDIO POWER AMPLIFIER WITH SHUTDOWN MODE Figure 35. Die Layout (B - Step) Table 1. Die/Wafer Characteristics Fabrication Attributes General Die Information Physical Die Identification LM4880B Bond Pad Opening Size (min) 86µm x 86µm Die Step B Bond Pad Metalization ALUMINUM Passivation NITRIDE Physical Attributes Wafer Diameter 150mm Back Side Metal Bare Back Dise Size (Drawn) 952µm x 1283µm 37mils x 51mils Back Side Connection GND Thickness 254µm Nominal Min Pitch 117µm Nominal Special Assembly Requirements: Note: Actual die size is rounded to the nearest micron. Die Bond Pad Coordinate Locations (B - Step) (Referenced to die center, coordinates in µm) NC = No Connection SIGNAL NAME PAD# NUMBER X/Y COORDINATES PAD SIZE X Y X BYPASS 1 -322 523 86 x 86 Y GND 2 -359 259 86 x 188 NC 3 -359 5 86 x 86 GND 4 -359 -259 86 x 188 SHUTDOWN 5 -323 -523 86 x 86 INPUT B 6 -109 -523 86 x 86 OUTPUT B 7 8 -523 86 x 86 Submit Documentation Feedback Copyright © 1995–2013, Texas Instruments Incorporated Product Folder Links: LM4880 13 LM4880 SNAS103C – NOVEMBER 1995 – REVISED MAY 2013 www.ti.com VDD 8 358 -78 86 x 188 GND 9 358 141 86 x 188 OUTPUT A 10 359 406 86 x 86 INPUT A 11 323 523 86 x 86 NC 12 8 523 86 x 86 NC 13 -109 523 86 x 86 14 Submit Documentation Feedback Copyright © 1995–2013, Texas Instruments Incorporated Product Folder Links: LM4880 LM4880 www.ti.com SNAS103C – NOVEMBER 1995 – REVISED MAY 2013 REVISION HISTORY Changes from Revision B (May 2013) to Revision C • Page Changed layout of National Data Sheet to TI format .......................................................................................................... 14 Submit Documentation Feedback Copyright © 1995–2013, Texas Instruments Incorporated Product Folder Links: LM4880 15 PACKAGE OPTION ADDENDUM www.ti.com 2-May-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (°C) Top-Side Markings (3) (4) LM4880M ACTIVE SOIC D 8 95 TBD Call TI Call TI -40 to 85 LM 4880M LM4880M/NOPB ACTIVE SOIC D 8 95 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 LM 4880M LM4880MX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 LM 4880M (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Top-Side Marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 Samples PACKAGE MATERIALS INFORMATION www.ti.com 8-May-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device LM4880MX/NOPB Package Package Pins Type Drawing SOIC D 8 SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 2500 330.0 12.4 Pack Materials-Page 1 6.5 B0 (mm) K0 (mm) P1 (mm) 5.4 2.0 8.0 W Pin1 (mm) Quadrant 12.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 8-May-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM4880MX/NOPB SOIC D 8 2500 367.0 367.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2013, Texas Instruments Incorporated