LM5642 High Voltage, Dual Synchronous Buck Converter with Oscillator Synchronization General Description Features The LM5642 consists of two current mode synchronous buck regulator controllers operating 180˚ out of phase with each other at a normal switching frequency of 200kHz. n Two synchronous buck regulators n 180˚ out of phase operation n Synchronizable switching frequency from 150kHz to 250kHz n 4.5V to 36V input range n 50µA Shutdown current n Adjustable output from 1.3V to 90% of Vin n 0.04% (typical) line and load regulation error n Current mode control with or without a sense resistor n Independent enable/soft-start pins allow simple sequential startup configuration. n Configurable for single output parallel operation. (See Figure 2) n Adjustable cycle-by-cycle current limit n Input under-voltage lockout n Output over-voltage latch protection n Output under-voltage protection with delay n Thermal shutdown n Self discharge of output capacitors when the regulator is OFF n TSSOP package Out of phase operation reduces the input ripple RMS current, thereby significantly reducing the required input capacitance. The switching frequency can be synchronized to an external clock between 150kHz and 250kHz. The two switching regulator outputs can also be paralleled to operate as a dual-phase single output regulator. The output of each channel can be independently adjusted from 1.3 to 90% of Vin. An internal 5V rail is also available externally for driving bootstrap circuitry. Current-mode feedback control assures excellent line and load regulation and a wide loop bandwidth for excellent response to fast load transients. Current is sensed across either the Vds of the top FET or across an external currentsense resistor connected in series with the drain of the top FET. The LM5642 features analog soft-start circuitry that is independent of the output load and output capacitance making the soft-start behavior more predictable and controllable than traditional soft-start circuits. Over-voltage protection is available for both outputs. A UVDelay pin is also available to allow delayed shut off time for the IC during an output under-voltage event. Applications n n n n n Embedded Computer Systems Telecom Systems Set-Top Boxes WebPAD Point Of Load Power Architectures Typical Application Circuit 20060101 © 2003 National Semiconductor Corporation DS200601 www.national.com LM5642 High Voltage, Dual Synchronous Buck Converter with Oscillator Synchronization September 2003 LM5642 Connection Diagram TOP VIEW 20060102 28-Lead TSSOP (MTC) Order Number LM5642MTC See NS Package Number MTC28 current source. When UV_DELAY charges to 2.3V (typical), the system immediately latches off. Connecting this pin to ground will disable the output under-voltage protection. VLIN5 (Pin 7): The output of an internal 5V LDO regulator derived from VIN. It supplies the internal bias for the chip and supplies the bootstrap circuitry for gate drive. Bypass this pin to signal ground with a minimum of 4.7µF ceramic capacitor. SGND (Pin 8): The ground connection for the signal-level circuitry. It should be connected to the ground rail of the system. ON/SS1 (Pin 9): Channel 1 enable pin. This pin is internally pulled up to one diode drop above VLIN5. Pulling this pin below 1.2V (open-collector type) turns off Channel 1. If both ON/SS1 and ON/SS2 pins are pulled below 1.2V, the whole chip goes into shut down mode. Adding a capacitor to this pin provides a soft-start feature that minimizes inrush current and output voltage overshoot. ON/SS2 (Pin 10): Channel 2 enable pin. See the description for Pin 9, ON/SS1. May be connected to ON/SS1 for simultaneous startup or for parallel operation. FB2 (Pin 11): Feedback input for channel 2. Connect to VOUT through a voltage divider to set the Channel 2 output voltage. COMP2 (Pin 12): Compensation pin for Channel 2. This is the output of the internal transconductance amplifier. The compensation network should be connected between this pin and the signal ground SGND (Pin 8). ILIM2 (Pin 13): Current limit threshold setting for Channel 2. See ILIM1 (Pin 2). KS2 (Pin 14): The positive (+) Kelvin sense for the internal current sense amplifier of Channel 2. See KS1 (Pin 1). RSNS2 (Pin 15): The negative (-) Kelvin sense for the internal current sense amplifier of Channel 2. Connect this pin to the low side of the current sense resistor that is placed between VIN and the drain of the top MOSFET. When the Pin Descriptions KS1 (Pin 1): The positive (+) Kelvin sense for the internal current sense amplifier of Channel 1. Use a separate trace to connect this pin to the current sense point. It should be connected to VIN as close as possible to the node of the current sense resistor. When no current-sense resistor is used, connect as close as possible to the drain node of the upper MOSFET. ILIM1 (Pin 2): Current limit threshold setting for Channel 1. It sinks a constant current of 9.9µA, which is converted to a voltage across a resistor connected from this pin to VIN. The voltage across the resistor is compared with either the VDS of the top MOSFET or the voltage across the external current sense resistor to determine if an over-current condition has occurred in Channel 1. COMP1 (Pin 3): Compensation pin for Channel 1. This is the output of the internal transconductance amplifier. The compensation network should be connected between this pin and the signal ground, SGND (Pin 8). FB1 (Pin 4): Feedback input for channel 1. Connect to VOUT through a voltage divider to set the Channel 1 output voltage. SYNC (Pin 5): The switching frequency of the LM5642 can be synchronized to an external clock. SYNC = LOW: Free running at 200kHz, channels are 180˚ out of phase. SYNC = HIGH: Waiting for external clock SYNC = Falling Edge: Channel 1 HDRV pin goes high. Channel 2 HDRV pin goes high after 2.5µs delay. The maximum SYNC pulse width must be greater than 100ns. For SYNC = Low operation, connect this pin to signal ground through a 220kΩ resistor. UV_DELAY (Pin 6): A capacitor from this pin to ground sets the delay time for UVP. The capacitor is charged from a 5µA www.national.com 2 LDRV2 (Pin 20): Low-side gate-drive output for Channel 2. (Continued) PGND (Pin 21): The power ground connection for both channels. Connect to the ground rail of the system. VIN (Pin 22): The power input pin for the chip. Connect to the positive (+) input rail of the system. This pin must be connected to the same voltage rail as the top FET drain (or the current sense resistor when used). Rds of the top MOSFET is used for current sensing, connect this pin to the source of the top MOSFET. Always use a separate trace to form a Kelvin connection to this pin. SW2 (Pin 16): Switch-node connection for Channel 2, which is connected to the source of the top MOSFET of Channel 2. It serves as the negative supply rail for the top-side gate driver, HDRV2. HDRV2 (Pin 17): Top-side gate-drive output for Channel 2. HDRV is a floating drive output that rides on the corresponding switching-node voltage. CBOOT2 (Pin 18): Bootstrap capacitor connection. It serves as the positive supply rail for the Channel 2 top-side gate drive. Connect this pin to VDD2 (Pin 19) through a diode, and connect the low side of the bootstrap capacitor to SW2 (Pin16). VDD2 (Pin 19): The supply rail for the Channel 2 low-side gate drive. Connected to VLIN5 (Pin 7) through a 4.7Ω resistor and bypassed to power ground with a ceramic capacitor of at least 1µF. Tie this pin to VDD1 (Pin 24). LDRV1 (Pin 23): Low-side gate-drive output for Channel 1. VDD1 (Pin 24): The supply rail for Channel 1 low-side gate drive. Tie this pin to VDD2 (Pin 19). CBOOT1 (Pin 25): : Bootstrap capacitor connection. It serves as the positive supply rail for Channel 1 top-side gate drive. See CBOOT2 (Pin 18). HDRV1 (Pin 26): Top-side gate-drive output for Channel 1. See HDRV2 (Pin 17). SW1 (Pin 27): Switch-node connection for Channel 1. See SW2 (Pin16). RSNS1 (Pin 28): The negative (-) Kelvin sense for the internal current sense amplifier of Channel 1. See RSNS2 (Pin 15). 3 www.national.com LM5642 Pin Descriptions LM5642 Absolute Maximum Ratings (Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. −0.3V to 38V SW1, SW2, RSNS1, RSNS2 −0.3 to (VIN + 0.3)V FB1, FB2, VDD1, VDD2 −0.3V to (VLIN5 +0.3)V ON/SS1, ON/SS2 (Note 2) −0.3V to (VLIN5 +0.6)V CBOOT1, CBOOT2 −0.3V to 7V LDRV1, LDRV2 −0.3V to (VDD+0.3)V HDRV1 to SW1, HDRV2 to SW2 1.1W −65˚C to +150˚C 4 sec, 260˚C 10sec, 240˚C 75sec, 219˚C ESD Rating (Note 5) 2kV Operating Ratings(Note 1) 43V CBOOT1 to SW1, CBOOT2 to SW2 Power Dissipation (TA = 25˚C), (Note 3) Soldering Dwell Time, Temperature (Note 4) Wave Infrared Vapor Phase −0.3V to 6V SYNC, COMP1, COMP2, UV Delay +0.3V Ambient Storage Temperature Range Voltages from the indicated pins to SGND/PGND: VIN, ILIM1, ILIM2, KS1, KS2 HDRV1 to CBOOT1, HDRV2 to CBOOT2 VIN (VLIN5 tied to VIN) 4.5V to 5.5V VIN (VIN and VLIN5 separate) 5.5V to 36V Junction Temperature −0.3V −40˚C to +125˚C Electrical Characteristics Unless otherwise specified, VIN = 28V, GND = PGND = 0V, VLIN5 = VDD1 = VDD2. Limits appearing in boldface type apply over the specified operating junction temperature range, (-40˚C to +125˚C, if not otherwise specified). Specifications appearing in plain type are measured using low duty cycle pulse testing with TA = 25˚C (Note 6), (Note 7). Min/Max limits are guaranteed by design, test, or statistical analysis. Symbol Parameter Conditions Min Typ Max Units System ∆VOUT/VOUT VFB1_FB2 IVIN Load Regulation VIN = 28V, Vcompx = 0.5V to 1.5V 0.04 % Line Regulation 5.5V ≤ VIN ≤ 36V, Vcompx =1.25V 0.04 % Feedback Voltage Input Supply Current 5.5V ≤ VIN ≤ 36V 1.2154 1.2364 1.2574 -20˚C to 85˚C 1.2179 1.2364 1.2549 VON_SSx > 2V 5.5V ≤ VIN ≤ 36V 1.1 2.0 mA Shutdown (Note 8) VON_SS1 = VON_SS2 = 0V 50 110 µA 5 5.30 V ±2 ± 7.0 mV 8.4 9.9 11.4 µA 0.5 2.4 5.0 µA 2 5.5 10 µA 0.7 1.12 1.4 V VLIN5 VLIN5 Output Voltage IVLIN5 = 0 to 25mA, 5.5V ≤ VIN ≤ 36V VCLos Current Limit Comparator Offset (VILIMX −VRSNSX) VIN = 6V 4.70 ICL Current Limit Sink Current Iss_SC1, Iss_SC2 Soft-Start Source Current VON_ss1 = VON_ss2 = 1.5V (on) Iss_SK1, Iss_SK2 Soft-Start Sink Current VON_ss1 = VON_ss2 = 1.5V VON_SS1, VON_SS2 Soft-Start On Threshold VSSTO Soft-Start Timeout Threshold (Note 9) Isc_uvdelay UV_DELAY Source Current UV-DELAY = 2V Isk_uvdelay UV_DELAY Sink Current UV-DELAY = 0.4V VUVDelay UV_DELAY Threshold Voltage www.national.com 3.4 V 2 5 9 µA 0.2 0.48 1.2 mA 2.3 4 V V (Continued) Unless otherwise specified, VIN = 28V, GND = PGND = 0V, VLIN5 = VDD1 = VDD2. Limits appearing in boldface type apply over the specified operating junction temperature range, (-40˚C to +125˚C, if not otherwise specified). Specifications appearing in plain type are measured using low duty cycle pulse testing with TA = 25˚C (Note 6), (Note 7). Min/Max limits are guaranteed by design, test, or statistical analysis. Symbol VUVP Parameter FB1, FB2, Under Voltage Protection Latch Threshold Conditions As a percentage of nominal output voltage (falling edge) Min Typ Max Units 75 80.7 86 % Hysteresis 3.7 VOUT Overvoltage Shutdown Latch Threshold As a percentage measured at VFB1, VFB2 SW1, SW2 ON-Resistance VSW1 = VSW2 = 0.4V ICBOOT CBOOTx Leakage Current VCBOOT1 = VCBOOT2 = 7V ISC_DRV HDRVx and LDRVx Source Current Isk_HDRV VOVP Swx_R % 107 114 122 % 420 487 560 Ω Gate Drive 10 nA VCBOOT1 = VCBOOT2 = 5V, VSWx=0V, HDRVx=LDRVx=2.5V 0.5 A HDRVx Sink Current VCBOOTx = VDDx = 5V, VSWx = 0V, HDRVX = 2.5V 0.8 A Isk_LDRV LDRVx Sink Current VCBOOTx = VDDx = 5V, VSWx = 0V, LDRVX = 2.5V 1.1 A RHDRV HDRV1 & 2 Source On-Resistance VCBOOT1 = VCBOOT2 = 5V, VSW1 = VSW2 = 0V 3.1 Ω 1.5 Ω 3.1 Ω 1.1 Ω HDRV1 & 2 Sink On-Resistance RLDRV LDRV1 & 2 Source On-Resistance LDRV1 & 2 Sink On-Resistance VCBOOT1 = VCBOOT2 = 5V, VSW1 = VSW2 = 0V VDD1 = VDD1 = 5V Oscillator and Sync Controls Fosc Oscillator Frequency 5.5 ≤ VIN ≤ 36V 166 200 Don_max Maximum On-Duty Cycle VFB1 = VFB2 = 1V, Measured at pins HDRV1 and HDRV2 96 98.9 % Ton_min Minimum On-Time 166 ns SSOT_delta HDRV1 and HDRV2 Delta On Time VHS SYNC Pin Min High Input VLS SYNC Pin Max Low Input ON/SS1 = ON/SS2 = 2V 20 2 226 250 1.52 kHz ns V 1.44 0.8 V 80 ± 200 nA Error Amplifier IFB1, IFB2 Feedback Input Bias Current VFB1_FIX = 1.5V, VFB2_FIX = 1.5V Icomp1_SC, Icomp2_SC COMP Output Source Current VFB1_FIX = VFB2_FIX = 1V, VCOMP1 = VCOMP2 = 1V 6 -20˚C to 85˚C 18 VFB1_FIX = VFB2_FIX = 1.5V and VCOMP1 = VCOMP2 = 0.5V 6 -20˚C to 85˚C 18 Icomp1_SK, Icomp2_SK gm1, gm2 COMP Output Sink Current Transconductance 127 118 720 5 µA µA µmho www.national.com LM5642 Electrical Characteristics LM5642 Electrical Characteristics (Continued) Unless otherwise specified, VIN = 28V, GND = PGND = 0V, VLIN5 = VDD1 = VDD2. Limits appearing in boldface type apply over the specified operating junction temperature range, (-40˚C to +125˚C, if not otherwise specified). Specifications appearing in plain type are measured using low duty cycle pulse testing with TA = 25˚C (Note 6), (Note 7). Min/Max limits are guaranteed by design, test, or statistical analysis. Symbol GISNS1, GISNS2 Parameter Current Sense Amplifier (1&2) Gain Conditions VCOMPx = 1.25V Min Typ Max 4.2 5.2 7.5 3.6 4.0 4.4 Units Voltage References and Linear Voltage Regulators UVLO VLIN5 Under-voltage Lockout Threshold Rising ON/SS1, ON/SS2 transition from low to high V Note 1: Absolute maximum ratings indicate limits beyond which damage to the device may occur. Operating Range indicates conditions for which the device is intended to be functional, but does not guarantee specfic performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions. Some performance characteristics may degrade when the device is not operated under the listed test conditions. Note 2: ON/SS1 and ON/SS2 are internally pulled up to one diode drop above VLIN5. Do not apply an external pull-up voltage to these pins. It may cause damage to the IC. Note 3: The maximum allowable power dissipation is calculated by using PDMAX = (TJMAX - TA)/θJA, where TJMAX is the maximum junction temperature, TA is the ambient temperature and θJA is the junction-to-ambient thermal resistance of the specified package. The 1.1W rating results from using 125˚C, 25˚C, and 90.6˚C/W for TJMAX, TA, and θJA respectively. A θJA of 90.6˚C/W represents the worst-case condition of no heat sinking of the 28-pin TSSOP. A thermal shutdown will occur if the temperature exceeds the maximum junction temperature of the device. Note 4: For detailed information on soldering plastic small-outline packages, refer to the Packaging Databook available from National Semiconductor Corporation. Note 5: For testing purposes, ESD was applied using the human-body model, a 100pF capacitor discharged through a 1.5kΩ resistor. Note 6: A typical is the center of characterization data measured with low duty cycle pulse tsting at TA = 25˚C. Typicals are not guaranteed. Note 7: All limits are guaranteed. All electrical characteristics having room-temperature limits are tested during production with TA = TJ = 25˚C. All hot and cold limits are guaranteed by correlating the electrical characteristics to process and temperature variations and applying statistical process control. Note 8: Both switching controllers are off. The linear regulator VLIN5 remains on. Note 9: When SS1 and SS2 pins are charged above this voltage and either of the output voltages at Vout1 or Vout2 is still below the regulation limit, the under voltage protection feature is initialized. www.national.com 6 LM5642 20060103 FIGURE 1. Typical 2 Channel Application Circuit 7 www.national.com LM5642 20060104 FIGURE 2. Typical Single Channel Application Circuit www.national.com 8 Block Diagram 20060105 LM5642 9 www.national.com LM5642 Typical Performance Characteristics Softstart Waveforms (No-Load Both Channels) UVP Startup Waveform (VIN = 24V) 20060168 20060123 Over-Current and UVP Shutdown (VIN = 24V, Io2 = 0A) Shutdown Waveforms (VIN = 24V, No-Load) 20060120 20060122 Ch.1 Load Transient Response (VIN = 24V, Vo1 = 1.8V) Ch.2 Load Transient Response (VIN = 24V, Vo2 = 3.3V) 20060165 www.national.com 20060129 10 LM5642 Typical Performance Characteristics (Continued) Ch. 2 Load Transient Response (VIN = 36V, Vo2 = 3.3V) Ch.1 Load Transient Response (VIN = 36V, Vo1 = 1.8V) 20060128 20060191 Input Supply Current vs VIN Shutdown Mode (25˚C) Input Supply Current vs Temperature (Shutdown Mode VIN = 28V) 20060124 20060125 VLIN5 vs Temperature VLIN5 vs VIN (25˚C) 20060126 20060127 11 www.national.com LM5642 Typical Performance Characteristics (Continued) Operating Frequency vs Temperature (VIN = 28V) FB Reference Voltage vs Temperature 20060166 20060167 Efficiency vs Load Current Using Resistor Sense Ch.1 = 1.8V, Ch.2 = Off Error Amplifier Tranconductance Gain vs Temperature 20060170 20060169 Efficiency vs Load Current Ch.2 = 3.3V, Ch.1 = Off Efficiency vs Load Current Using Vds Sense Ch.2 = 1.8V, Ch.2 = Off 20060172 20060171 www.national.com 12 LM5642 Typical Performance Characteristics (Continued) Efficiency vs Load Current Using Vds Sense Ch.2 = 3.3V, Ch.1 = Off 20060173 13 www.national.com LM5642 Operating Descriptions SOFT START The ON/SS1 pin has dual functionality as both channel enable and soft start control. Referring to the soft start block diagram is shown in Figure 3, the LM5642 will remain shutdown mode while both soft start pins are grounded. The LM5642 will remain in shutdown mode while both soft start pins are grounded. In a normal application (with a soft start capacitor connected between the ON/SS1 pin and SGND) soft start functions as follows. As the input voltage rises (note: Iss starts to flow when VIN ≥ 2.2V), the internal 5V LDO starts up, and an internal 2.4µA current charges the soft start capacitor. During soft start, the error amplifier output voltage at the COMPx pin is clamped at 0.55V and the duty cycle is controlled only by the soft start voltage. As the SSx pin voltage ramps up, the duty cycle increases proportional to the soft start ramp, causing the output voltage to ramp up. The rate at which the duty cycle increases depends on the capacitance of the soft start capacitor. The higher the capacitance, the slower the output voltage ramps up. When the corresponding output voltage exceeds 98% (typical) of the set target voltage, the regulator switches from soft start to normal operating mode. At this time, the 0.55V clamp at the output of the error amplifier releases and peak current feedback control takes over. Once in peak current feedback control mode, the output of the error amplifier will travel within the 0.5V and 2V window to achieve PWM control. See Figure 4. The amount of capacitance needed for a desired soft-start time can be approximated in the following equation: 20060106 FIGURE 3. Soft-Start and ON/OFF 20060107 (1) In this equation Iss = 2.4µA for one channel and 4.8µA if the channels are paralleled. tss is the desired soft-start time. Finally, FIGURE 4. Voltage Clamp at COMPx Pin (2) During soft start, over-voltage protection and current limit remain in effect. The under voltage protection feature is activated when the ON/SS pin exceeds the timeout threshold (3.4V typical). If the ON/SSx capacitor is too small, the duty cycle may increase too rapidly, causing the device to latch off due to output voltage overshoot above the OVP threshold. This becomes more likely in applications requiring low output voltage, high input voltage and light load. A capacitance of 10nF is recommended at each soft start pin to provide a smooth monotonic output ramp. 20060108 FIGURE 5. OVP and UVP OVER VOLTAGE PROTECTION (OVP) If the output voltage on either channel rises above 113% of nominal, over voltage protection activates. Both channels will latch off. When the OVP latch is set, the high side FET driver, HDRVx, is immediately turned off and the low side FET driver, LDRVx, is turned on to discharge the output www.national.com 14 noise, especially during heavy load transients and short on time conditions. The filter components should be connected as close as possible to the IC. (Continued) capacitor through the inductor. To reset the OVP latch, either the input voltage must be cycled, or both channels must be switched off. As shown in Figure 6, adding a resistor in series with the SWx pin will slow down the gate drive (HDRVx), thus slowing the rise and fall time of the top FET, yielding a longer drain current transition time. Usually a 3.3Ω to 4.7Ω resistor is sufficient to suppress the noise. Top FET switching losses will increase with higher resistance values. Small resistors (1-5 ohms) can also be placed in series with the HDRVx pin or the CBOOTx pin to effectively reduce switch node ringing. A CBOOT resistor will slow the rise time of the FET, whereas a resistor at HDRV will reduce both rise and fall times. UNDER VOLTAGE PROTECTION (UVP) AND UV DELAY If the output voltage on either channel falls below 80% of nominal, under voltage protection activates. As shown in Figure 5, an under-voltage event will shut off the UV_DELAY MOSFET, which will allow the UV_DELAY capacitor to charge at 5µA (typical). At the UV_DELAY threshold (2.3V typical) both channels will latch off. Also, UV_DELAY will be disabled and the UV_DELAY pin will return to 0V. During UVP, both the high side and low side FET drivers will be turned off. If no capacitor is connected to the UV_DELAY pin, the UVP latch will be activated immediately. To reset the UVP latch, either the input voltage must be cycled, or both ON/SS pins must be pulled low. The UVP function can be disabled by connecting the UV_DELAY pin to ground. THERMAL SHUTDOWN The LM5642 IC will enter thermal shutdown if the die temperature exceeds 160˚C. The top and bottom FETs of both channels will be turned off immediately. In addition, both soft capacitors will begin to discharge through separate 5.5µA current sinks. The voltage on both capacitors will settle to approximately 1.1V, where it will remain until the thermal shutdown condition has cleared. The IC will return to normal operating mode when the die temperature has fallen to below 146˚C. At this point the two soft start capacitors will begin to charge with their normal 2.4µA current sources. This allows a controlled return to normal operation, similar to the soft start during turn-on. If the thermal shutdown condition clears before the voltage on the soft start capacitors has fallen to 1.1V, the capacitors will first be discharged to 1.1V, and then immediately begin charging back up. 20060109 FIGURE 6. SW Series Resistor CURRENT SENSING AND LIMITING As shown in Figure 7, the KSx and RSNSx pins are the inputs of the current sense amplifier. Current sensing is accomplished either by sensing the Vds of the top FET or by sensing the voltage across a current sense resistor connected from VIN to the drain of the top FET. The advantages of sensing current across the top FET are reduced parts count, cost and power loss. The RDS-ON of the top FET is not as stable over temperature and voltage as a sense resistor, hence great care must be used in layout for VDS sensing circuits. At input voltages above 30V, the maximum recommended output current is 5A per channel. Keeping the differential current-sense voltage below 200mV ensures linear operation of the current sense amplifier. Therefore, the RDS-ON of the top FET or the current sense resistor must be small enough so that the current sense voltage does not exceed 200mV when the top FET is on. There is a leading edge blanking circuit that forces the top FET on for at least 166ns. Beyond this minimum on time, the output of the PWM comparator is used to turn off the top FET. Additionally, a minimum voltage of at least 50mV across Rsns is recommended to ensure a high SNR at the current sense amplifier. Assuming a maximum of 200mV across Rsns, the current sense resistor can be calculated as follows: OUTPUT CAPACITOR DISCHARGE Each channel has an embedded 480Ω MOSFET with the drain connected to the SWx pin. This MOSFET will discharge the output capacitor of its channel if its channel is off, or the IC enters a fault state caused by one of the following conditions: 1. UVP 2. UVLO If an output over voltage event occurs, the HDRVx will be turned off and LDRVx will be turned on immediately to discharge the output capacitor of both channels through the inductor. SWITCHING NOISE REDUCTION Power MOSFETs are very fast switching devices. In synchronous rectifier converters, the rapid increase of drain current in the top FET coupled with parasitic inductance will generate unwanted Ldi/dt noise spikes at the source node of the FET (SWx node) and also at the VIN node. The magnitude of this noise will increase as the output current increases. This parasitic spike noise may turn into electromagnetic interference (EMI), and can also cause problems in device performance. Therefore, it must be suppressed using one of the following methods. When using resistor sense, it is strongly recommended to add R-C filters to the current sense amplifier inputs as shown in Figure 7. This will reduce the susceptibility to switching (3) where Imax is the maximum expected load current, including overload multiplier (ie:120%), and Irip is the inductor ripple current (See Equation 3). The above equation gives the maximum allowable value for Rsns. Switching losses will increase with Rsns, thus lowering efficiency. 15 www.national.com LM5642 Operating Descriptions LM5642 Operating Descriptions INPUT UNDER VOLTAGE LOCKOUT (UVLO) The input under-voltage lock out threshold, which is sensed via the VLIN5 internal LDO output, is 4.0V (typical). Below this threshold, both HDRVx and LDRVx will be turned off and the internal 480Ω MOSFETs will be turned on to discharge the output capacitors through the SWx pins. During UVLO, the ON/SS pins will sink 5mA to discharge the soft start capacitors and turn off both channels. As the input voltage increases again above 4.0V, UVLO will be de-activated, and the device will restart again from soft start phase. If the voltage at VLIN5 remains below 4.5V, but above the 4.0V UVLO threshold, the device cannot be guaranteed to operate within specification. If the input voltage is between 4.0V and 5.2V, the VLIN5 pin will not regulate, but will follow approximately 200mV below the input voltage. (Continued) The peak current limit is set by an external resistor connected between the ILIMx pin and the KSx pin. An internal 10µA current sink on the ILIMx pin produces a voltage across the resistor to set the current limit threshold which is compared to the current sense voltage. A 10nF capacitor across this resistor is required to filter unwanted noise that could improperly trip the current limit comparator. DUAL-PHASE PARALLEL OPERATION In applications with high output current demand, the two switching channels can be configured to operate as a two phase converter to provide a single output voltage with current sharing between the two switching channels. This approach greatly reduces the stress and heat on the output stage components while lowering input ripple current. The sum of inductor ripple current is also reduced which results in lowering output ripple voltage. Figure 2 shows an example of a typical two-phase circuit. Because precision current sense is the primary design criteria to ensure accurate current sharing between the two channels, both channels must use external sense resistors for current sensing. To minimize the error between the error amplifiers of the two channels, tie the feedback pins FB1 and FB2 together and connect to a single voltage divider for output voltage sensing. Also, tie the COMP1 and COMP2 together and connect to the compensation network. ON/SS1 and ON/SS2 must be tied together to enable and disable both channels simultaneously. 20060110 FIGURE 7. Current Sense and Current Limit Current limit is activated when the inductor current is high enough to cause the voltage at the RSNSx pin to be lower than that of the ILIMx pin. This toggles the comparator, thus turning off the top FET immediately. The comparator is disabled either when the top FET is turned off or during the leading edge blanking time. The equation for current limit resistor, Rlim, is as follows: EXTERNAL FREQUENCY SYNC The LM5642 has the ability to synchronize to external sources in order to set the switching frequency. This allows the chip to use frequencies from 150kHz to 250kHz. Lowering the switching frequency allows a smaller minimum duty cycle, DMIN, and hence a greater range between input and output voltage. Increasing switching frequency allows the use of smaller output inductors and output capacitors (See Component Selection). In general, synching all the switching frequencies in multi-converter systems makes filtering of the switching noise easier. The sync input can be from a system clock, from another switching converter in the system, or from any other periodic signal with a low-level less than 1.4V and a high level greater than 2V. Both CMOS and TTL level inputs are acceptable. The LM5642 uses a fixed delay scheme in order to ensure a 180˚ phase difference between Channel 1 and Channel 2. Due the nominal switching frequency of 200kHz, which corresponds to a switching period of 5µs, Channel 2 always begins its period 2.5µs after Channel 1 (Figure 8a). When the converter is synched to a frequency other than 200kHz, the switching period is reduced or increased, while the fixed delay between Channel 1 and Channel 2 remains the same. The phase difference between channels is therefore no longer 180˚. At the extremes of the sync range, the phase difference drops to 135˚ (Figure 8b) and Figure 8c). The result of this lower phase difference is a reduction in the maximum duty cycle of one channel that will not overlap the duty cycle of the other. As shown in Input Capacitor Selec- (4) Where Ilim is the load current at which the current limit comparator will be tripped. When sensing current across the top FET, replace Rsns with the RDS-ON of the FET. This calculated Rlim value guarantees that the minimum current limit will not be less than Imax. It is recommended that a 1% tolerance resistor be used. When sensing across the top FET, RDS-ON will show more variation than a current sense resistor, largely due to temperature. RDS-ON will increase proportional to temperature according to a specific temperature coefficient. Refer to the manufacturer’s datasheet to determine the range of RDS-ON values over operating temperature or see the Component Selection section (Equation 4) for a calculation of maximum RDS-ON. This will prevent RDS-ON variations from prematurely setting off the current limit comparator as the operating temperature increases. To ensure accurate current sensing using VDS sense, special attention in board layout is required. The KSx and RSNSx pins require separate traces to form a Kelvin connection to the corresponding current sense nodes. In addition, the filter components R14, R16, C14, C15 should be removed. www.national.com 16 LM5642 Operating Descriptions (Continued) tion section, when the duty cycle D1 for Channel 1 overlaps the duty cycle D2 for Channel 2, the input rms current increases, requiring more input capacitors or input capacitors with higher ripple current ratings. The new, reduced maximum duty cycle can be calculated by multiplying the sync frequency (in Hz) by 2.5x10-6 (the fixed delay in seconds). (5) DMAX = FSYNC*2.5x10-6 (6) Where Vfb=1.238V. Although increasing the value of R1 and R2 will increase efficiency, this will also decrease accuracy. Therefore, a maximum value is recommended for R2 in order to keep the output within .3% of Vnom. This maximum R2 value should be calculated first with the following equation: (7) Where 200nA is the maximum current drawn by FBx pin. 20060180 (a) 20060111 FIGURE 9. Output Voltage Setting Example: Vnom=5V, Vfb=1.2364V, Ifbmax=200nA. 20060181 (b) (8) Choose 60K (9) The Cycle Skip and Dropout modes of the LM5642 IC regulate the minimum and maximum output voltage/duty cycle that the converter can deliver. Both modes check the voltage at the COMP pin. Minimum output voltage is determined by the Cycle Skip Comparator. This circuitry skips the high side FET ON pulse when the COMP pin voltage is below 0.5V at the beginning of a cycle. The converter will continue to skip every other pulse until the duty cycle (and COMP pin voltage) rise above 0.5V, effectively halving the switching frequency. Maximum output voltage is determined by the Dropout circuitry, which skips the low side FET ON pulse whenever the COMP pin voltage exceeds the ramp voltage derived from the current sense. Up to three low side pulses may be skipped in a row before a minimum duty pulse must be applied to the low side FET. Figure 10 shows the range of ouput voltage (for Io = 3A) with respect to input voltage that will keep the converter from entering either Skip Cycle or Dropout mode. For input voltages below 5.5V, VLIN5 must be connected to Vin through a small resistor (approximately 4.7 ohm). This will ensure that VLIN5 does not fall below the UVLO threshold. 20060182 (c) FIGURE 8. At a sync frequency of 150kHz, for example, the maximum duty cycle for Channel 1 that will not overlap Channel 2 would be 37.5%. At 250kHz, it is the duty cycle for Channel 2 that is reduced to a DMAX of 37.5%. Component Selection OUTPUT VOLTAGE SETTING The output voltage for each channel is set by the ratio of a voltage divider as shown in Figure 9. The resistor values can be determined by the following equation: 17 www.national.com LM5642 Component Selection MAXIMUM ESR CALCULATION (Continued) Unless the rise and fall times of a load transient are slower than the response speed of the control loop, if the total combined ESR (Re) is too high, the load transient requirement will not be met, no matter how large the capacitance. The maximum allowed total combined ESR is: (12) Example: ∆Vc_s = 160mV, ∆Ic_s = 3A. Then Re_max = 53.3mΩ. Maximum ESR criterion can be used when the associated capacitance is high enough, otherwise more capacitors than the number determined by this criterion should be used in parallel. MINIMUM CAPACITANCE CALCULATION In a switch mode power supply, the minimum output capacitance is typically dictated by the load transient requirement. If there is not enough capacitance, the output voltage excursion will exceed the maximum allowed value even if the maximum ESR requirement is met. The worst-case load transient is an unloading transient that happens when the input voltage is the highest and when the present switching cycle has just finished. The corresponding minimum capacitance is calculated as follows: 20060113 FIGURE 10. Output Voltage Range Output Capacitor Selection In applications that exhibit large and fast load current swings, the slew rate of such a load current transient may be beyond the response speed of the regulator. Therefore, to meet voltage transient requirements during worst-case load transients, special consideration should be given to output capacitor selection. The total combined ESR of the output capacitors must be lower than a certain value, while the total capacitance must be greater than a certain value. Also, in applications where the specification of output voltage regulation is tight and ripple voltage must be low, starting from the required output voltage ripple will often result in fewer design iterations. (13) Notice it is already assumed the total ESR, Re, is no greater than Re_max, otherwise the term under the square root will be a negative value. Also, it is assumed that L has already been selected, therefore the minimum L value should be calculated before Cmin and after Re (see Inductor Selection below). Example: Re = 20mΩ, Vnom = 5V, ∆Vc_s = 160mV, ∆Ic_s = 3A, L = 8µH ALLOWED TRANSIENT VOLTAGE EXCURSION The allowed output voltage excursion during a load transient (∆Vc_s) is: (10) Where ± δ% is the output voltage regulation window and ± e% is the output voltage initial accuracy. Example: Vnom = 5V, δ% = 7%, e% = 3.4%, Vrip = 40mV peak to peak. (14) Generally speaking, Cmin decreases with decreasing Re, ∆Ic_s, and L, but with increasing Vnom and ∆Vc_s. Inductor Selection The size of the output inductor can be determined from the desired output ripple voltage, Vrip, and the impedance of the output capacitors at the switching frequency. The equation to determine the minimum inductance value is as follows: (11) Since the ripple voltage is included in the calculation of ∆Vc_s, the inductor ripple current should not be included in the worst-case load current excursion. That is, the worstcase load current excursion should be simply maximum load current change specification, ∆Ic_s. www.national.com (15) In the above equation, Re is used in place of the impedance of the output capacitors. This is because in most cases, the impedance of the output capacitors at the switching frequency is very close to Re. In the case of ceramic capacitors, replace Re with the true impedance. 18 perature as well as the maximum input voltage. In applications in which output voltages are less than half of the input voltage, the corresponding duty cycles will be less than 50%. This means there will be no overlap between the two channels’ input current pulses. The equation for calculating the maximum total input ripple RMS current for duty cycles under 50% is: (Continued) Example: Vin = 36V, Vo = 3.3V, VRIP = 60mV, Re = 20mΩ, F = 200kHz. (16) The actual selection process usually involves several iterations of all of the above steps, from ripple voltage selection, to capacitor selection, to inductance calculations. Both the highest and the lowest input and output voltages and load transient requirements should be considered. If an inductance value larger than Lmin is selected, make sure that the Cmin requirement is not violated. Priority should be given to parameters that are not flexible or more costly. For example, if there are very few types of capacitors to choose from, it may be a good idea to adjust the inductance value so that a requirement of 3.2 capacitors can be reduced to 3 capacitors. (21) where I1 is maximum load current of Channel 1, I2 is the maximum load current of Channel 2, D1 is the duty cycle of Channel 1, and D2 is the duty cycle of Channel 2. Example: Imax_1 = 3.6A, Imax_2 = 3.6A, D1 = 0.42, and D2 = 0.275 Since inductor ripple current is often the criterion for selecting an output inductor, it is a good idea to double-check this value. The equation is: (22) Choose input capacitors that can handle 1.66A ripple RMS current at highest ambient temperature. In applications where output voltages are greater than half the input voltage, the corresponding duty cycles will be greater than 50%, and there will be overlapping input current pulses. Input ripple current will be highest under these circumstances. The input RMS current in this case is given by: (17) Also important is the ripple content, which is defined by Irip /Inom. Generally speaking, a ripple content of less than 50% is ok. Larger ripple content will cause too much loss in the inductor. Example: Vin = 36V, Vo = 3.3V, F = 200kHz, L = 5µH, 3A max IOUT (23) Where, again, I1 and I2 are the maximum load currents of channel 1 and 2, and D1 and D2 are the duty cycles. This equation should be used when both duty cycles are expected to be higher than 50%. If the LM5642 is being used with an external clock frequency other than 200kHz, the preceding equations for input rms current can still be used. The selection of the first equation or the second changes because overlap can now occur at duty cycles that are less than 50%. From the External Frequency Sync section, the maximum duty cycle that ensures no overlap between duty cycles (and hence input current pulses) is: (24) DMAX = FSYNC* 2.5 x 10-6 There are now three distinct possibilities which must be considered when selecting the equation for input rms current: 1. Both duty cycles D1 and D2 are less than DMAX. In this case, the first, simple equation can always be used. 2. One duty cycle is greater than DMAX and the other duty cycle is less than DMAX. In this case, the system designer can take advantage of the fact that the sync feature reduces DMAX for one channel, but lengthens it for the other channel. For FSYNC < 200kHz, D1 is reduced to DMAX while D2 actually increases to (1-DMAX). For FSYNC > 200kHz, D2 is reduced to DMAX while D1 increases to (1-DMAX). By using the channel reduced to DMAX for the lower duty cycle, and the channel that has been increased for the higher duty cycle, the first, simple rms input current equation can be used. (18) 3A is 100% ripple which is too high. In this case, the inductor should be reselected on the basis of ripple current. Example: 40% ripple, 40% • 3A = 1.2A (19) (20) When choosing the inductor, the saturation current should be higher than the maximum peak inductor current and the RMS current rating should be higher than the maximum load current. Input Capacitor Selection The fact that the two switching channels of the LM5642 are 180˚ out of phase will reduce the RMS value of the ripple current seen by the input capacitors. This will help extend input capacitor life span and result in a more efficient system. Input capacitors must be selected that can handle both the maximum ripple RMS current at highest ambient tem- 19 www.national.com LM5642 Inductor Selection LM5642 Input Capacitor Selection 35.3mΩ) can be used in parallel. In this case, the temperature rise on each FET will not go to Tj_max because each FET is now dissipating only half of the total power. (Continued) 3. Both duty cycles are greater than DMAX. This case is identical to a system at 200kHz where either duty cycle is 50% or greater. Some overlap of duty cycles is guaranteed, and hence the second, more complicated rms input current equation must be used. Input capacitors must meet the minimum requirements of voltage and ripple current capacity. The size of the capacitor should then be selected based on hold up time requirements. Bench testing for individual applications is still the best way to determine a reliable input capacitor value. Input capacitors should always be placed as close as possible to the current sense resistor or the drain of the top FET. When high ESR capacitors such as tantalum are used, a 1µF ceramic capacitor should be added as closely as possible to the high-side FET drain and low-side FET source. TOP FET SELECTION The top FET has two types of losses: switching loss and conduction loss. The switching losses mainly consist of crossover loss and bottom diode reverse recovery loss. Since it is rather difficult to estimate the switching loss, a general starting point is to allot 60% of the top FET thermal capacity to switching losses. The best way to precisely determine switching losses is through bench testing. The equation for calculating the on resistance of the top FET is thus: MOSFET Selection BOTTOM FET SELECTION (27) During normal operation, the bottom FET is switching on and off at almost zero voltage. Therefore, only conduction losses are present in the bottom FET. The most important parameter when selecting the bottom FET is the on resistance (RDS-ON). The lower the on resistance, the lower the power loss. The bottom FET power loss peaks at maximum input voltage and load current. The equation for the maximum allowed on resistance at room temperature for a given FET package, is: Example: Tj_max = 100˚C, Ta_max = 60˚C, Rqja = 60˚C/W, Vin_min = 5.5V, Vnom = 5V, and Iload_max = 3.6A. (28) When using FETs in parallel, the same guidelines apply to the top FET as apply to the bottom FET. Loop Compensation The general purpose of loop compensation is to meet static and dynamic performance requirements while maintaining stability. Loop gain is what is usually checked to determine small-signal performance. Loop gain is equal to the product of control-output transfer function and the output-control transfer function (the compensation network transfer function). Generally speaking it is a good idea to have a loop gain slope that is -20dB /decade from a very low frequency to well beyond the crossover frequency. The crossover frequency should not exceed one-fifth of the switching frequency. The higher the bandwidth is, the faster the load transient response speed will potentially be. However, if the duty cycle saturates during a load transient, further increasing the small signal bandwidth will not help. Since the control-output transfer function usually has very limited low frequency gain, it is a good idea to place a pole in the compensation at zero frequency, so that the low frequency gain will be relatively large. A large DC gain means high DC regulation accuracy (i.e. DC voltage changes little with load or line variations). The rest of the compensation scheme depends highly on the shape of the control-output plot. (25) where Tj_max is the maximum allowed junction temperature in the FET, Ta_max is the maximum ambient temperature, Rθja is the junction-to-ambient thermal resistance of the FET, and TC is the temperature coefficient of the on resistance which is typically in the range of 10,000ppm/˚C. If the calculated RDS-ON (MAX) is smaller than the lowest value available, multiple FETs can be used in parallel. This effectively reduces the Imax term in the above equation, thus reducing RDS-ON. When using two FETs in parallel, multiply the calculated RDS-ON (MAX) by 4 to obtain the RDS-ON (MAX) for each FET. In the case of three FETs, multiply by 9. (26) If the selected FET has an Rds value higher than 35.3Ω, then two FETs with an RDS-ON less than 141mΩ (4 x www.national.com 20 LM5642 Loop Compensation (Continued) (32) First determine the minimum frequency (fpmin) of the pole across the expected load range, then place the first compensation zero at or below that value. Once fpmin is determined, Rc1 should be calculated using: (33) Where B is the desired gain in V/V at fp (fz1), gm is the transconductance of the error amplifier, and R1 and R2 are the feedback resistors. A gain value around 10dB (3.3v/v) is generally a good starting point. 20060114 Example: B=3.3v/v, gm=650m, R1=20KΩ, R2=60.4KΩ: FIGURE 11. Control-Output Transfer Function As shown in Figure 11, the control-output transfer function consists of one pole (fp), one zero (fz), and a double pole at fn (half the switching frequency). The following can be done to create a -20dB /decade roll-off of the loop gain: Place the first pole at 0Hz, the first zero at fp, the second pole at fz, and the second zero at fn. The resulting output-control transfer function is shown in Figure 12. (34) Bandwidth will vary proportional to the value of Rc1. Next, Cc1 can be determined with the following equation: (35) Example: fpmin=695Hz, Rc1=20KΩ: (36) The compensation network (Figure 13) will also introduce a low frequency pole which will be close to 0Hz. A second pole should also be placed at fz. This pole can be created with a single capacitor Cc2 and a shorted Rc2 (see Figure 13). The minimum value for this capacitor can be calculated by: 20060112 FIGURE 12. Output-Control Transfer Function The control-output corner frequencies, and thus the desired compensation corner frequencies, can be determined approximately by the following equations: (37) Cc2 may not be necessary, however it does create a more stable control loop. This is especially important with high load currents and in current sharing mode. Example: fz=80kHz, Rc1= 20KΩ: (29) (30) Since fp is determined by the output network, it will shift with loading (Ro). It is best to use a minimum Iout value of approximately 100mA when determining the maximum Ro value. Example: Re=20mΩ, Co=100uF, Romax=5V/100mA=50Ω: (38) A second zero can also be added with a resistor in series with Cc2. If used, this zero should be placed at fn, where the control to output gain rolls off at -40dB/dec. Generally, fn will be well below the 0dB level and thus will have little effect on stability. Rc2 can be calculated with the following equation: (31) (39) 21 www.national.com LM5642 Loop Compensation (Continued) 20060174 FIGURE 13. Compensation Network Bill Of Materials for Figure 1 24V to 1.8,3.3V ID Part Number Type Size U1 LM5642 Dual Synchronous Controller TSSOP-28 Q1, Q4 Si4850EY N-MOSFET SO-8 Q2, Q5 Si4840DY N-MOSFET SO-8 D3 BAS40-06 Schottky Diode L1 RLF12560T-4R2N100 Parameters Qty Vendor 1 NSC 60V 2 Vishay 40V 2 Vishay SOT-23 40V 1 ON Inductor 12.5x12.5x 6mm 4.2µH, 7mΩ 10A 1 TDK L2 RLF12545T-100M5R1 Inductor 12.5x12.5x 4.5mm 10µH, 12mΩ 5.1A 1 TDK C1 C3216X7R1H105K Capacitor 1206 1µF, 50V 1 TDK C3, C4, C14, C15 VJ1206Y101KXXAT Capacitor 1206 100pF, 25V 3 Vishay C27 C2012X5R1C105K Capacitor 0805 1µF, 16V 1 TDK C6, C16 C5750X5R1H106M Capacitor 2220 10µF 50V, 2.8A 2 TDK C9, C23 6TPD330M Capacitor 7.3x4.3x 3.8mm 330µF, 6.3V, 10mΩ 2 Sanyo C2, C11, C12, C13 VJ1206Y103KXXAT Capacitor 1206 10nF, 25V 4 Vishay C7, C25, C34 VJ1206Y104KXXAT Capacitor 1206 100nF, 25V 3 Vishay C19 VJ1206Y822KXXAT Capacitor 1206 8.2nF 10% 1 Vishay C20 VJ1206Y153KXXAT Capacitor 1206 15nF 10% 1 Vishay C26 C3216X7R1C475K Capacitor 1206 4.7µF 25V 1 TDK R1 CRCW1206123J Resistor 1206 12kΩ 5% 1 Vishay R2, R6, R14, R16 CRCW1206100J Resistor 1206 100Ω 5% 1 Vishay R13 CRCW1206682J Resistor 1206 6.8kΩ 12% 1 Vishay R7, R15 WSL-2512 .010 1% Resistor 2512 10mΩ 1W 2 Vishay R8, R9, R12, R17, R18, R21, R31, R32 CRCW1206000Z Resistor 1206 0Ω 8 Vishay R10 CRCW12062261F Resistor 1206 2.26kΩ 1% 1 Vishay Vishay R23 CRCW12068451F Resistor 1206 8.45kΩ 1% 1 R24 CRCW12061372F Resistor 1206 13.7kΩ 1% 1 Vishay R11, R20 CRCW12064991F Resistor 1206 4.99kΩ 1% 2 Vishay R19 CRCW12068251F Resistor 1206 8.25kΩ 1% 1 Vishay R27 CRCW12064R7J Resistor 1206 4.7Ω 5% 1 Vishay R28 CRCW1206224J Resistor 1206 220kΩ 5% 1 Vishay www.national.com 22 ID Part Number Type Size U1 LM5642 Dual Synchronous Controller TSSOP-28 Parameters Qty Vendor 1 NSC Q1, Q4 Si4850EY N-MOSFET SO-8 60V 2 Vishay Q2, Q3, Q5, Q6 Si4470DY N-MOSFET SO-8 60V 4 Vishay D3 BAS40-06 Schottky Diode SOT-23 40V 1 ON L1,L2 RLF12560T-2R7N110 Inductor 12.5x12.5x 6mm 2.7µH,4.5mΩ 11.5A 2 TDK C1 C3216X7R1H105K Capacitor 1206 1µF, 50V 1 TDK C10, C24, C27 C2012X5R1C105K Capacitor 0805 1µF, 16V 3 TDK C6, C16, C28, C30 C5750X5R1H106M Capacitor 2220 10µF 50V, 2.8A 4 TDK C9, C23 16MV1000WX Capacitor 10mm D20mm H 1000µF, 16V, 22mΩ 2 Sanyo C2, C13 VJ1206Y103KXXAT Capacitor 1206 10nF, 25V 2 Vishay C11 VJ1206Y223KXXAT Capacitor 1206 22nF, 25V 1 Vishay C7,C25, C34 VJ1206Y104KXXAT Capacitor 1206 100nF, 25V 3 Vishay C19 VJ1206Y273KXXAT Capacitor 1206 27nF 10% 1 Vishay C26 C3216X7R1C475K Capacitor 1206 4.7µF 25V 1 TDK R1, R13 CRCW1206123J Resistor 1206 16.9kΩ 1% 1 Vishay R2, R6, R14, R16 CRCW1206100J Resistor 1206 100Ω 5% 1 Vishay R7, R15 WSL-2512 .010 1% Resistor 2512 10mΩ 1W 2 Vishay R8, R9, R12, R17, R18, R21, R31, R32 CRCW1206000Z Resistor 1206 0Ω 8 Vishay R10 CRCW12062261F Resistor 1206 2.26kΩ 1% 1 Vishay R11 CRCW12064991F Resistor 1206 4.99kΩ 1% 1 Vishay Vishay R23 CRCW12061152F Resistor 1206 11.5kΩ 1% 1 R27 CRCW12064R7J Resistor 1206 4.7Ω 5% 1 Vishay R28 CRCW1206224J Resistor 1206 220kΩ 5% 1 Vishay 23 www.national.com LM5642 Bill of Materials for Figure 2 30V to 1.8V, 20A LM5642 High Voltage, Dual Synchronous Buck Converter with Oscillator Synchronization Physical Dimensions inches (millimeters) unless otherwise noted 28-Lead TSSOP Package Order Number LM5642MTC NS Package Number MTC28 LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Americas Customer Support Center Email: [email protected] Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: [email protected] Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Support Center Email: [email protected] National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: [email protected] Tel: 81-3-5639-7560 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.