LINER LTC2493CDEPBF

LTC2493
24-Bit 2-/4-Channel
DS ADC with Easy Drive Input Current
Cancellation and I2C Interface
Description
Features
Up to 2 Differential or 4 Single-Ended Inputs
■ Easy DriveTM Technology Enables Rail-to-Rail
Inputs with Zero Differential Input Current
■ Directly Digitizes High Impedance Sensors with
Full Accuracy
■ 2-Wire I2C Interface with 9 Addresses Plus One
Global Address for Synchronization
■ 600nV RMS Noise
■ Integrated High Accuracy Temperature Sensor
■ GND to V
CC Input/Reference Common Mode Range
■ Programmable 50Hz, 60Hz or Simultaneous 50Hz/
60Hz Rejection Mode
■ 2ppm INL, No Missing Codes
■ 1ppm Offset and 15ppm Full-Scale Error
■ 2x Speed/Reduced Power Mode (15Hz Using Internal
Oscillator and 80µA at 7.5Hz Output)
■ No Latency: Digital Filter Settles in a Single Cycle,
Even After a New Channel Is Selected
■ Single Supply 2.7V to 5.5V Operation (0.8mW)
■ Internal Oscillator
■ Tiny 4mm × 3mm DFN Package
■
Applications
■
■
■
■
Direct Sensor Digitizer
Direct Temperature Measurement
Instrumentation
Industrial Process Control
The LTC®2493 is a 4-channel (2-channel differential), 24-bit,
No Latency DSTM ADC with Easy Drive technology and a
2-wire, I2C interface. The patented sampling scheme eliminates dynamic input current errors and the shortcomings
of on-chip buffering through automatic cancellation of
differential input current. This allows large external source
impedances and rail-to-rail input signals to be directly
digitized while maintaining exceptional DC accuracy.
The LTC2493 includes a high accuracy temperature
sensor and an integrated oscillator. This device can be
configured to measure an external signal (from combinations of 4 analog input channels operating in singleended or differential modes) or its internal temperature
sensor. The integrated temperature sensor offers 1/30th
°C resolution and 2°C absolute accuracy.
The LTC2493 allows a wide common mode input range
(0V to VCC), independent of the reference voltage. Any
combination of single-ended or differential inputs can
be selected and the first conversion, after a new channel
is selected, is valid. Access to the multiplexer output enables optional external amplifiers to be shared between all
analog inputs and auto calibration continuously removes
their associated offset and drift.
, LT, LTC and LTM are registered trademarks of Linear Technology Corporation.
No Latency DS and Easy Drive are trademarks of Linear Technology Corporation. All other
trademarks are the property of their respective owners.
Typical Application
Data Acquisition System with Temperature Compensation
Integrated High Performance Temperature Sensor
5
2.7V TO 5.5V
4
4-CHANNEL
MUX
IN+
TEMPERATURE
SENSOR
1.7k
24-BIT ∆Σ ADC
WITH EASY-DRIVE
IN–
CH3
COM
REF +
10µF
REF –
SDA
SCL
2-WIRE
I2C INTERFACE
CA1
CA0
9-PIN SELECTABLE
ADDRESSES
FO
OSC
2493 vTA01a
3
ABSOLUTE ERROR (°C)
CH2
0.1µF
VCC
CH0
CH1
2
1
0
–1
–2
–3
–4
–5
–55
–30
–5
20
45
70
TEMPERATURE (°C)
95
120
2493 TA02
2493fa
LTC2493
Absolute Maximum Ratings
pIN CONFIGURATION
(Notes 1, 2)
Supply Voltage (VCC).................................... –0.3V to 6V
Analog Input Voltage
(CH0 to CH3, COM)...................–0.3V to (VCC + 0.3V)
REF+, REF–. ...................................–0.3V to (VCC + 0.3V)
Digital Input Voltage.......................–0.3V to (VCC + 0.3V)
Digital Output Voltage....................–0.3V to (VCC + 0.3V)
Operating Temperature Range
LTC2493C................................................. 0°C to 70°C
LTC2493I.............................................. –40°C to 85°C
Storage Temperature Range.................... –65°C to 150°C
FO
1
14 REF–
CA0
2
13 REF+
CA1
3
SCL
4
SDA
5
10 CH2
GND
6
9 CH1
COM
7
8 CH0
12 VCC
15
11 CH3
DE PACKAGE
14-LEAD (4mm × 3mm) PLASTIC DFN
TJMAX = 125°C, θJA = 37°C/W
EXPOSED PAD (PIN 15) IS GND, MUST BE SOLDERED TO PCB
order information
LEAD FREE FINISH
TAPE AND REEL
PART MARKING*
PACKAGE DESCRIPTION
TEMPERATURE RANGE
LTC2493CDE#PBF
LTC2493IDE#PBF
LTC2493CDE#TRPBF
LTC2493IDE#TRPBF
2493
2493
14-Lead (4mm × 3mm) Plastic DFN
14-Lead (4mm × 3mm) Plastic DFN
0°C to 70°C
–40°C to 85°C
Consult LTC Marketing for parts specified with wider operating temperature ranges.
Consult LTC Marketing for information on non-standard lead based finish parts.
*For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
2493fa
LTC2493
Electrical
Characteristics (Normal Speed)
The ● denotes the specifications which
apply over the full operating temperature range, otherwise specifications are at TA = 25°C. (Notes 3, 4)
PARAMETER
CONDITIONS
Resolution (No Missing Codes)
0.1V ≤ VREF ≤ VCC, –FS ≤ VIN ≤ +FS (Note 5)
MIN
TYP
MAX
UNITS
Integral Nonlinearity
5V ≤ VCC ≤ 5.5V, VREF = 5V, VIN(CM) = 2.5V (Note 6)
2.7V ≤ VCC ≤ 5.5V, VREF = 2.5V, VIN(CM) = 1.25V (Note 6)
●
●
2
1
10
Offset Error
2.5V ≤ VREF ≤ VCC, GND ≤ IN+ = IN– ≤ VCC (Note 13)
●
0.5
2.5
Offset Error Drift
2.5V ≤ VREF ≤ VCC, GND ≤ IN+ = IN– ≤ VCC
Positive Full-Scale Error
2.5V ≤ VREF ≤ VCC, IN+ = 0.75VREF , IN– = 0.25VREF
Positive Full-Scale Error Drift
2.5V ≤ VREF ≤ VCC, IN+ = 0.75VREF , IN– = 0.25VREF
Negative Full-Scale Error
2.5V ≤ VREF ≤ VCC, IN+ = 0.25VREF , IN– = 0.75VREF
Negative Full-Scale Error Drift
2.5V ≤ VREF ≤ VCC, IN+ = 0.25VREF , IN– = 0.75VREF
0.1
ppm of VREF/°C
Total Unadjusted Error
5V ≤ VCC ≤ 5.5V, VREF = 2.5V, VIN(CM) = 1.25V
5V ≤ VCC ≤ 5.5V, VREF = 5V, VIN(CM) = 2.5V
2.7V ≤ VCC ≤ 5.5V, VREF = 2.5V, VIN(CM) = 1.25V
15
15
15
ppm of VREF
ppm of VREF
ppm of VREF
Output Noise
2.7V < VCC < 5.5V, 2.5V ≤ VREF ≤ VCC,
GND ≤ IN+ = IN– ≤ VCC (Note 12)
0.6
µVRMS
Internal PTAT Signal
TA = 27°C (Note 13)
24
Bits
ppm of VREF
ppm of VREF
µV
10
nV/°C
25
●
0.1
ppm of VREF
ppm of VREF/°C
25
●
27.8
28.0
Internal PTAT Temperature Coefficient
ppm of VREF
28.2
mV
93.5
µV/°C
Electrical
Characteristics (2x Speed)
The ● denotes the specifications which apply over the
full operating temperature range, otherwise specifications are at TA = 25°C. (Notes 3, 4)
PARAMETER
CONDITIONS
Resolution (No Missing Codes)
0.1V ≤ VREF ≤ VCC, –FS ≤ VIN ≤ +FS (Note 5)
MIN
TYP
MAX
UNITS
Integral Nonlinearity
5V ≤ VCC ≤ 5.5V, VREF = 5V, VIN(CM) = 2.5V (Note 6)
2.7V ≤ VCC ≤ 5.5V, VREF = 2.5V, VIN(CM) = 1.25V (Note 6)
●
Offset Error
2.5V ≤ VREF ≤ VCC, GND ≤ IN+ = IN– ≤ VCC (Note 13)
●
Offset Error Drift
2.5V ≤ VREF ≤ VCC, GND ≤ IN+ = IN– ≤ VCC
Positive Full-Scale Error
2.5V ≤ VREF ≤ VCC, IN+ = 0.75VREF , IN– = 0.25VREF
Positive Full-Scale Error Drift
2.5V ≤ VREF ≤ VCC, IN+ = 0.75VREF , IN– = 0.25VREF
Negative Full-Scale Error
2.5V ≤ VREF ≤ VCC, IN+ = 0.25VREF , IN– = 0.75VREF
Negative Full-Scale Error Drift
2.5V ≤ VREF ≤ VCC, IN+ = 0.25VREF , IN– = 0.75VREF
0.1
ppm of VREF/°C
Output Noise
5V ≤ VCC ≤ 5.5V, VREF = 5V, GND ≤ IN+ = IN– ≤ VCC
0.85
µVRMS
24
Bits
2
1
10
0.2
2
ppm of VREF
ppm of VREF
mV
100
nV/°C
25
●
0.1
ppm of VREF
ppm of VREF/°C
25
●
ppm of VREF
Converter
Characteristics
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. (Note 3)
PARAMETER
CONDITIONS
Input Common Mode Rejection DC
2.5V ≤ VREF ≤ VCC, GND ≤ IN+ = IN– ≤ VCC (Note 5)
MIN
, GND ≤ IN+ = IN– ≤ V
TYP
MAX
UNITS
●
140
dB
Input Common Mode Rejection 50Hz ±2%
2.5V ≤ VREF ≤ VCC
CC (Notes 5, 7)
●
140
dB
Input Common Mode Rejection 60Hz ±2%
2.5V ≤ VREF ≤ VCC, GND ≤ IN+ = IN– ≤ VCC (Notes 5, 8)
●
140
dB
110
120
dB
110
120
dB
, GND ≤ IN+ = IN– ≤ V
Input Normal Mode Rejection 50Hz ±2%
2.5V ≤ VREF ≤ VCC
CC (Notes 5, 7)
●
Input Normal Mode Rejection 60Hz ±2%
2.5V ≤ VREF ≤ VCC, GND ≤ IN+ = IN– ≤ VCC (Notes 5, 8)
●
, GND ≤ IN+ = IN– ≤ V
Input Normal Mode Rejection 50Hz/60Hz ±2%
2.5V ≤ VREF ≤ VCC
Reference Common Mode Rejection DC
2.5V ≤ VREF ≤ VCC, GND ≤ IN+ = IN– ≤ VCC (Note 5)
CC (Notes 5, 9)
= 2.5V, IN+ = IN– = GND
Power Supply Rejection DC
VREF
Power Supply Rejection, 50Hz ±2%, 60Hz ±2%
VREF = 2.5V, IN+ = IN– = GND (Notes 7, 8, 9)
●
87
●
120
dB
140
dB
120
dB
120
dB
2493fa
LTC2493
Analog
Input and Reference
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. (Note 3)
SYMBOL
PARAMETER
IN+
Absolute/Common Mode IN+ Voltage
(IN+ Corresponds to the Selected Positive Input Channel)
CONDITIONS
GND – 0.3V
MIN
VCC + 0.3V
V
IN–
Absolute/Common Mode IN– Voltage
(IN– Corresponds to the Selected Negative Input Channel)
GND – 0.3V
VCC + 0.3V
V
VIN
Input Differential Voltage Range (IN+ – IN–)
●
–FS
+FS
V
FS
Full Scale of the Differential Input (IN+ – IN–)
●
0.5VREF
LSB
Least Significant Bit of the Output Code
●
FS/224
REF+
Absolute/Common Mode REF+ Voltage
●
0.1
VCC
V
REF–
Absolute/Common Mode REF– Voltage
●
GND
REF+ – 0.1V
V
VREF
Reference Voltage Range (REF+ – REF–)
●
0.1
CS(IN+)
IN+ Sampling Capacitance
11
pF
CS(IN–)
IN– Sampling Capacitance
11
pF
CS(VREF)
VREF Sampling Capacitance
11
pF
IDC_LEAK(IN+)
IDC_LEAK(IN–)
IDC_LEAK(REF+)
IDC_LEAK(REF–)
IN+ DC Leakage Current
Sleep Mode, IN+ = GND
●
–10
1
10
nA
IN– DC Leakage Current
Sleep Mode, IN– = GND
●
–10
1
10
nA
REF+ DC Leakage Current
Sleep Mode, REF+ = V
●
–100
1
100
nA
REF– DC Leakage Current
Sleep Mode, REF– = GND
●
–100
1
100
nA
tOPEN
MUX Break-Before-Make
QIRR
MUX Off Isolation
CC
VIN = 2VP-P DC to 1.8MHz
TYP
MAX
UNITS
V
VCC
V
50
ns
120
dB
I 2C Inputs And Digital Outputs
The ● denotes the specifications which apply over the full
operating temperature range, otherwise specifications are at TA = 25°C. (Note 3)
SYMBOL
PARAMETER
VIH
High Level Input Voltage
CONDITIONS
●
MIN
TYP
MAX
VIL
Low Level Input Voltage
●
0.3VCC
V
VIHA
Low Level Input Voltage for Address Pins CA0, CA1
●
0.05VCC
V
VILA
High Level Input Voltage for Address Pins CA0, CA1
●
RINH
Resistance from CA0, CA1 to VCC to Set Chip Address
Bit to 1
●
10
kW
RINL
Resistance from CA0, CA1 to GND to Set Chip Address
Bit to 0
●
10
kW
RINF
Resistance from CA0, CA1 to GND or VCC to Set Chip
Address Bit to Float
●
2
II
Digital Input Current (fO)
●
–10
VHYS
Hysteresis of Schmitt Trigger Inputs
(Note 5)
●
0.05VCC
VOL
Low Level Output Voltage (SDA)
I = 3mA
●
tOF
Output Fall Time VIH(MIN) to VIL(MAX)
Bus Load CB 10pF to
400pF (Note 14)
●
IIN
Input Leakage (SDA, SCL)
0.1VCC ≤ VIN ≤ 0.9VCC
CCAX
External Capacitative Load on Chip Address Pins (CA0,
CA1) for Valid Float
0.7VCC
UNITS
V
0.95VCC
V
MW
10
µA
V
0.4
V
250
ns
●
1
µA
●
10
pF
20 + 0.1CB
2493fa
LTC2493
Power
Requirements
The ● denotes the specifications which apply over the full operating temperature
range, otherwise specifications are at TA = 25°C. (Note 3)
SYMBOL
PARAMETER
VCC
Supply Voltage
ICC
Supply Current
CONDITIONS
MIN
Conversion Current (Note 11)
Temperature Measurement (Note 11)
Sleep Mode (Note 11)
TYP
2.7
●
160
200
1
●
●
●
MAX
UNITS
5.5
V
275
300
2
µA
µA
µA
Digital
Inputs And Digital Outputs
The ● denotes the specifications which apply over the
full operating temperature range, otherwise specifications are at TA = 25°C. (Note 3)
SYMBOL
PARAMETER
CONDITIONS
MIN
fEOSC
External Oscillator Frequency Range
(Note 16)
tHEO
External Oscillator High Period
tLEO
External Oscillator Low Period
tCONV_1
Conversion Time for 1x Speed Mode
50Hz Mode
60Hz Mode
Simultaneous 50Hz/60Hz Mode
External Oscillator (Note 10)
tCONV_2
Conversion Time for 2x Speed Mode
50Hz Mode
60Hz Mode
Simultaneous 50Hz/60Hz Mode
External Oscillator (Note 10)
TYP
MAX
UNITS
●
10
4000
kHz
●
0.125
50
µs
●
0.125
50
µs
●
●
●
157.2
131
144.1
160.3
133.6
146.9
41036/fEOSC (in kHz)
163.5
136.3
149.9
ms
ms
ms
ms
●
●
●
78.7
65.6
72.2
80.3
66.9
73.6
81.9
68.2
75.1
ms
ms
ms
ms
20556/fEOSC (in kHz)
I 2C TIMING CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. (Note 3, 15)
SYMBOL
PARAMETER
fSCL
SCL Clock Frequency
CONDITIONS
●
MIN
0
TYP
MAX
UNITS
400
kHz
tHD(STA)
Hold Time (Repeated) Start Condition
●
0.6
µs
tLOW
Low Period of the SCL Pin
●
1.3
µs
tHIGH
High Period of the SCL Pin
●
0.6
µs
tSU(STA)
Set-Up Time for a Repeated Start Condition
●
0.6
µs
0
tHD(DAT)
Data Hold Time
●
tSU(DAT)
Data Set-Up Time
●
100
tr
Rise Time for SDA Signals
(Note 14)
●
20 + 0.1CB
300
ns
tf
Fall Time for SDA Signals
(Note 14)
●
20 + 0.1CB
300
ns
tSU(STO)
Set-Up Time for Stop Condition
●
0.6
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: All voltage values are with respect to GND.
Note 3: Unless otherwise specified: VCC = 2.7V to 5.5V
VREFCM = VREF/2, FS = 0.5VREF
VIN = IN+ – IN–, VIN(CM) = (IN+ – IN–)/2,
where IN+ and IN– are the selected input channels.
Note 4: Use internal conversion clock or external conversion clock source
with fEOSC = 307.2kHz unless otherwise specified.
Note 5: Guaranteed by design, not subject to test.
Note 6: Integral nonlinearity is defined as the deviation of a code from a
straight line passing through the actual endpoints of the transfer curve.
The deviation is measured from the center of the quantization band.
0.9
µs
ns
µs
Note 7: 50Hz mode (internal oscillator) or fEOSC = 256kHz ±2% (external oscillator).
Note 8: 60Hz mode (internal oscillator) or fEOSC = 307.2kHz ±2% (external oscillator).
Note 9: Simultaneous 50Hz/60Hz mode (internal oscillator) or fEOSC =
280kHz ±2% (external oscillator).
Note 10: The external oscillator is connected to the FO pin. The external
oscillator frequency, fEOSC, is expressed in kHz.
Note 11: The converter uses its internal oscillator.
Note 12: The output noise includes the contribution of the internal
calibration operations.
Note 13: Guaranteed by design and test correlation.
Note 14: CB = capacitance of one bus line in pF (10pF ≤ CB ≤ 400pF).
Note 15: All values refer to VIH(MIN) and VIL(MAX) levels.
Note 16: Refer to Applications Information section for Performance vs
Data Rate graphs.
2493fa
LTC2493
Typical Performance Characteristics
–45°C
2
25°C
0
85°C
–1
1
–45°C, 25°C, 85°C
0
–1
–2
–2
–3
–2.5 –2 –1.5 –1 –0.5 0 0.5 1 1.5
INPUT VOLTAGE (V)
2
–0.75
–0.25
0.25
0.75
INPUT VOLTAGE (V)
4
0
25°C
Total Unadjusted Error
(VCC = 5V, VREF = 2.5V)
12
VCC = 5V
VREF = 2.5V
VIN(CM) = 1.25V
FO = GND
8
85°C
TUE (ppm of VREF)
TUE (ppm of VREF)
8
–45°C
–4
–8
2
85°C
–45°C
0
–4
12
12
NUMBER OF READINGS (%)
4
–0.75
–0.25
0.25
0.75
INPUT VOLTAGE (V)
–4
–0.25
0.25
0.75
INPUT VOLTAGE (V)
–3 –2.4 –1.8 –1.2 –0.6 0 0.6
OUTPUT READING (µV)
VCC = 5V
TA = 25°C
VREF = 5V RMS NOISE = 0.60µV
VIN = 0V
VIN(CM) = 2.5V
4
3
4
0
1.25
Long-Term ADC Readings
6
0
2493 G07
–0.75
2493 G06
5
8
2
1.8
85°C
–45°C
–12
–1.25
1.25
10,000 CONSECUTIVE
READINGS
RMS = 0.59µV
VCC = 2.7V
AVERAGE = –0.19µV
VREF = 2.5V
10 VIN = 0V
TA = 25°C
2
1.2
25°C
0
Noise Histogram (7.5sps)
14
6
1.25
2493 G03
–8
Noise Histogram (6.8sps)
NUMBER OF READINGS (%)
4
2493 G05
14
8
–0.25
0.25
0.75
INPUT VOLTAGE (V)
VCC = 2.7V
VREF = 2.5V
VIN(CM) = 1.25V
FO = GND
8
4
–12
–1.25
2.5
10,000 CONSECUTIVE
READINGS
RMS = 0.60µV
VCC = 5V
AVERAGE = –0.69µV
VREF = 5V
10 VIN = 0V
TA = 25°C
–0.75
Total Unadjusted Error
(VCC = 2.7V, VREF = 2.5V)
25°C
2493 G04
–3 –2.4 –1.8 –1.2 –0.6 0 0.6
OUTPUT READING (µV)
–1
12
–8
–12
–2.5 –2 –1.5 –1 –0.5 0 0.5 1 1.5
INPUT VOLTAGE (V)
–45°C, 25°C, 85°C
0
2493 G02
Total Unadjusted Error
(VCC = 5V, VREF = 5V)
VCC = 5V
VREF = 5V
VIN(CM) = 2.5V
FO = GND
1
–3
–1.25
1.25
2493 G01
12
VCC = 2.7V
VREF = 2.5V
VIN(CM) = 1.25V
FO = GND
–2
–3
–1.25
2.5
Integral Nonlinearity
(VCC = 2.7V, VREF = 2.5V)
2
ADC READING (µV)
INL (ppm of VREF)
1
3
VCC = 5V
VREF = 2.5V
VIN(CM) = 1.25V
FO = GND
TUE (ppm of VREF)
2
3
VCC = 5V
VREF = 5V
VIN(CM) = 2.5V
FO = GND
INL (ppm of VREF)
3
Integral Nonlinearity
(VCC = 5V, VREF = 2.5V)
INL (ppm of VREF)
Integral Nonlinearity
(VCC = 5V, VREF = 5V)
2
1
0
–1
–2
–3
–4
1.2
1.8
2493 G08
–5
0
10
30
40
20
TIME (HOURS)
50
60
2493 G09
2493fa
LTC2493
Typical Performance Characteristics
RMS Noise
vs Input Differential Voltage
RMS NOISE (µV)
0.8
VCC = 5V
VREF = 5V
VIN(CM) = 2.5V
TA = 25°C
FO = GND
VCC = 5V
VREF = 5V
VIN = 0V
TA = 25°C
FO = GND
0.9
0.8
0.7
0.6
0.6
0.4
2.5
–1
0
2
1
3
5
4
1.0
VREF = 2.5V
VIN = 0V
VIN(CM) = GND
TA = 25°C
FO = GND
0.6
0.7
0.6
0.5
3.5
3.9 4.3
VCC (V)
4.7
5.1
0.4
5.5
0
1
2
3
VREF (V)
4
0.1
0.3
OFFSET ERROR (ppm of VREF)
OFFSET ERROR (ppm of VREF)
0.2
0
–0.1
–0.2
–0.3
–45 –30 –15
0 15 30 45 60
TEMPERATURE (°C)
75
90
2493 G16
0.2
0.1
0
–0.1
–0.2
–0.3
–1
0
1
3
2
VIN(CM) (V)
5
4
0.2
0.1
Offset Error vs VCC
0.3
REF+ = 2.5V
REF– = GND
VIN = 0V
VIN(CM) = GND
TA = 25°C
FO = GND
0
Offset Error vs VREF
VCC = 5V
REF – = GND
VIN = 0V
VIN(CM) = GND
TA = 25°C
FO = GND
0.2
0.1
0
–0.1
–0.1
–0.2
–0.3
2.7
6
2493 G15
OFFSET ERROR (ppm of VREF)
Offset Error vs Temperature
VCC = 5V
VREF = 5V
VIN = 0V
VIN(CM) = GND
FO = GND
VCC = 5V
VREF = 5V
VIN = 0V
TA = 25°C
FO = GND
2493 G14
2493 G13
0.3
5
90
Offset Error vs VIN(CM)
0.3
VCC = 5V
VIN = 0V
VIN(CM) = GND
TA = 25°C
FO = GND
0.8
0.5
3.1
75
2493 G12
RMS Noise vs VREF
0.9
0.7
0 15 30 45 60
TEMPERATURE (°C)
2493 G11
RMS Noise vs VCC
0.4
2.7
0.4
–45 –30 –15
6
OFFSET ERROR (ppm of VREF)
RMS NOISE (µV)
0.8
0.6
VIN(CM) (V)
RMS NOISE (µV)
0.9
0.7
0.5
2493 G10
1.0
0.8
0.5
0.4
–2.5 –2 –1.5 –1 –0.5 0 0.5 1 1.5 2
INPUT DIFFERENTIAL VOLTAGE (V)
VCC = 5V
VREF = 5V
VIN = 0V
VIN(CM) = GND
FO = GND
0.9
0.7
0.5
RMS Noise vs Temperature (TA)
1.0
RMS NOISE (µV)
0.9
RMS Noise vs VIN(CM)
1.0
RMS NOISE (µV)
1.0
–0.2
3.1
3.5
3.9 4.3
VCC (V)
4.7
5.1
5.5
2493 G17
–0.3
0
1
2
3
VREF (V)
4
5
2493 G18
2493fa
LTC2493
Typical Performance Characteristics
On-Chip Oscillator Frequency
vs VCC
310
308
308
306
304
VCC = 4.1V
VREF = 2.5V
VIN = 0V
VIN(CM) = GND
FO = GND
300
–45 –30 –15
306
304
75
300
90
2.5
–60
–80
3.0
3.5
4.0
VCC (V)
4.5
5.0
–120
–140
30600
30650
30700
30750
FREQUENCY AT VCC (Hz)
1.6
VCC = 5V
1.0
0.8
0.6
VCC = 2.7V
0.4
0 15 30 45 60
TEMPERATURE (°C)
75
90
2493 G25
FO = GND
VCC = 5V
160
VCC = 2.7V
140
120
100
–45 –30 –15
30800
0 15 30 45 60
TEMPERATURE (°C)
400
350
2
VCC = 5V
VCC = 3V
0
Integral Nonlinearity (2x Speed
Mode; VCC = 5V, VREF = 5V)
VCC = 5V
VREF = 5V
VIN(CM) = 2.5V
FO = GND
25°C, 85°C
–1
200
100
90
1
300
250
75
2493 G24
3
–2
150
0.2
0
–45 –30 –15
VREF = VCC
IN+ = GND
IN– = GND
FO = EXT OSC
TA = 25°C
450
SUPPLY CURRENT (µA)
SLEEP MODE CURRENT (µA)
500
1M
180
Conversion Current
vs Output Data Rate
FO = GND
1.2
10k 100k
1k
100
FREQUENCY AT VCC (Hz)
2493 G23
Sleep Mode Current
vs Temperature
1.4
10
2493 G21
200
2493 G22
1.8
1
Conversion Current
vs Temperature
–80
–120
2.0
–140
PSRR vs Frequency at VCC
–60
–100
0 20 40 60 80 100 120 140 160 180 200 220
FREQUENCY AT VCC (Hz)
5.5
VCC = 4.1V DC ±0.7V
V
= 2.5V
–20 INREF
+ = GND
–
IN = GND
–40 FO = GND
TA = 25°C
–100
–140
–80
CONVERSION CURRENT (µA)
REJECTION (dB)
–40
0
REJECTION (dB)
–20
–60
2493 G20
PSRR vs Frequency at VCC
VCC = 4.1V DC ±1.4V
VREF = 2.5V
IN+ = GND
IN– = GND
FO = GND
TA = 25°C
–40
–120
2493 G19
0
VCC = 4.1V DC ±0.7V
VREF = 2.5V
IN+ = GND
IN– = GND
FO = GND
TA = 25°C
–100
302
0 15 30 45 60
TEMPERATURE (°C)
PSRR vs Frequency at VCC
–20
INL (µV)
302
VREF = 2.5V
VIN = 0V
VIN(CM) = GND
FO = GND
TA = 25°C
0
REJECTION (dB)
310
FREQUENCY (kHz)
FREQUENCY (kHz)
On-Chip Oscillator Frequency
vs Temperature
0
10 20 30 40 50 60 70 80 90 100
OUTPUT DATA RATE (READINGS/SEC)
2493 G26
–45°C
–3
–2.5 –2 –1.5 –1 –0.5 0 0.5 1 1.5
INPUT VOLTAGE (V)
2
2.5
2493 G27
2493fa
LTC2493
Typical Performance Characteristics
3
3
VCC = 5V
VREF = 2.5V
VIN(CM) = 1.25V
FO = GND
1
2
INL (ppm OF VREF)
2
INL (ppm OF VREF)
Integral Nonlinearity (2x Speed
Mode; VCC = 2.7V, VREF = 2.5V)
85°C
0
–45°C, 25°C
–1
–2
16
VCC = 2.7V
VREF = 2.5V
VIN(CM) = 1.25V
FO = GND
1
85°C
0
–45°C, 25°C
–1
–2
–3
–1.25
–0.75
–0.25
0.25
0.75
INPUT VOLTAGE (V)
–3
–1.25
1.25
–0.75
–0.25
0.25
0.75
INPUT VOLTAGE (V)
198
196
OFFSET ERROR (µV)
RMS NOISE (µV)
0.8
0.6
0.4
VCC = 5V
VIN = 0V
VIN(CM) = GND
FO = GND
TA = 25°C
5
2493 G31
183.8
186.2
OUTPUT READING (µV)
194
230
192
190
188
186
180
188.6
2493 G30
240
VCC = 5V
VREF = 5V
VIN = 0V
FO = GND
TA = 25°C
220
VCC = 5V
VREF = 5V
VIN = 0V
VIN(CM) = GND
FO = GND
210
200
190
180
170
182
4
181.4
Offset Error vs Temperature
(2x Speed Mode)
184
3
2
VREF (V)
4
0
179
1.25
OFFSET ERROR (µV)
200
1
6
Offset Error vs VIN(CM)
(2x Speed Mode)
1.0
0
8
2493 G29
RMS Noise vs VREF
(2x Speed Mode)
0.2
RMS = 0.85µV
10,000 CONSECUTIVE
AVERAGE = 0.184mV
14 READINGS
VCC = 5V
12 VREF = 5V
VIN = 0V
T = 25°C
10 A
2
2493 G28
0
Noise Histogram
(2x Speed Mode)
NUMBER OF READINGS (%)
Integral Nonlinearity (2x Speed
Mode; VCC = 5V, VREF = 2.5V)
–1
0
1
3
VIN(CM) (V)
2
4
5
6
2493 G32
160
–45 –30 –15
0 15 30 45 60
TEMPERATURE (°C)
75
90
2493 G33
2493fa
LTC2493
Typical Performance Characteristics
250
240
VREF = 2.5V
VIN = 0V
VIN(CM) = GND
FO = GND
TA = 25°C
150
100
50
PSRR vs Frequency at VCC
(2x Speed Mode)
0
VCC = 5V
VIN = 0V
VIN(CM) = GND
FO = GND
TA = 25°C
230
OFFSET ERROR (µV)
200
OFFSET ERROR (µV)
Offset Error vs VREF
(2x Speed Mode)
220
–40
210
200
190
2
2.5
3
4
3.5
VCC (V)
4.5
5.5
5
160
1
0
2
4
3
VREF (V)
–60
10
10k 100k
1k
100
FREQUENCY AT VCC (Hz)
1M
2493 G36
0
VCC = 4.1V DC ±1.4V
REF+ = 2.5V
REF– = GND
IN+ = GND
IN– = GND
FO = GND
TA = 25°C
VCC = 4.1V DC ±0.7V
REF+ = 2.5V
REF– = GND
IN+ = GND
–40 IN– = GND
FO = GND
–60 TA = 25°C
–20
–80
–80
–100
–100
–120
–120
–140
1
PSRR vs Frequency at VCC
(2x Speed Mode)
REJECTION (dB)
RREJECTION (dB)
–40
–140
5
2493 G35
PSRR vs Frequency at VCC
(2x Speed Mode)
–20
–80
–120
2493 G34
0
–60
–100
180
170
0
VCC = 4.1V DC ±0.7V
REF+ = 2.5V
REF– = GND
IN+ = GND
IN– = GND
FO = GND
TA = 25°C
–20
REJECTION (dB)
Offset Error vs VCC
(2x Speed Mode)
0 20 40 60 80 100 120 140 160 180 200 220
FREQUENCY AT VCC (Hz)
2493 G37
–140
30600
30650
30700
30750
FREQUENCY AT VCC (Hz)
30800
2493 G38
2493fa
10
LTC2493
Pin Functions
FO (Pin 1): Frequency Control Pin. Digital input that controls
the internal conversion clock rate. When FO is connected
to GND, the converter uses its internal oscillator running at
307.2kHz. The conversion clock may also be overridden by
driving the FO pin with an external clock in order to change
the output rate and the digital filter rejection null.
CA0, CA1 (Pins 2, 3): Chip Address Control Pins. These
pins are configured as a three-state (LOW, HIGH, Floating)
address control bits for the device’s I2C address.
SCL (Pin 4): Serial Clock Pin of the I2C Interface. The
LTC2493 can only act as a slave and the SCL pin only accepts an external serial clock. Data is shifted into the SDA
pin on the rising edges of the SCL clock and output through
the SDA pin on the falling edges of the SCL clock.
SDA (Pin 5): Bidirectional Serial Data Line of the I2C Inter-
face. In the transmitter mode (Read), the conversion result
is output through the SDA pin, while in the receiver mode
(Write), the device channel select and configuration bits
are input through the SDA pin. The pin is high impedance
during the data input mode and is an open drain output
(requires an appropriate pull-up device to VCC) during the
data output mode.
GND (Pin 6): Ground. Connect this pin to a common ground
plane through a low impedance connection.
COM (Pin 7): The Common Negative Input (IN –) for All
Single-Ended Multiplexer Configurations. The voltage
on CH0-CH3 and COM pins can have any value between
GND – 0.3V to VCC + 0.3V. Within these limits, the two
selected inputs (IN+ and IN– ) provide a bipolar input
range (VIN = IN+ – IN– ) from –0.5 • VREF to 0.5 • VREF .
Outside this input range, the converter produces unique
over-range and under-range output codes.
CH0 to CH3 (Pin 8-Pin 11): Analog Inputs. May be programmed for single-ended or differential mode.
VCC (Pin 12): Positive Supply Voltage. Bypass to GND with
a 10µF tantalum capacitor in parallel with a 0.1µF ceramic
capacitor as close to the part as possible.
REF+, REF – (Pin 13, Pin 14): Differential Reference Input.
The voltage on these pins can have any value between
GND and VCC as long as the reference positive input, REF+,
remains more positive than the negative reference input,
REF–, by at least 0.1V. The differential voltage (VREF = REF+
– REF –) sets the full-scale range for all input channels.
Exposed Pad (Pin 15): Ground. This pin is ground and
must be soldered to the PCB ground plane. For prototyping
purposes, this pin may remain floating.
2493fa
11
LTC2493
FUNCTIONAL Block Diagram
VCC
INTERNAL
OSCILLATOR
TEMP
SENSOR
GND
CH0
CH1
CH2
CH3
COM
FO
(INT/EXT)
AUTOCALIBRATION
AND CONTROL
REF +
REF –
IN+
MUX
IN–
–
+
1.7k
DIFFERENTIAL
3RD ORDER
∆Σ MODULATOR
I2C
INTERFACE
SDA
SCL
CA0
CA1
DECIMATING FIR
ADDRESS
2493 BD
2493fa
12
LTC2493
Applications Information
CONVERTER OPERATION
Converter Operation Cycle
The LTC2493 is a multichannel, low power, delta-sigma
analog-to-digital converter with a 2-wire, I2C interface.
Its operation is made up of four states (see Figure 1).
The converter operating cycle begins with the conversion, followed by the sleep state and ends with the data
input/output cycle .
Initially, at power-up, the LTC2493 performs a conversion.
Once the conversion is complete, the device enters the
sleep state. While in the sleep state, power consumption is
reduced by two orders of magnitude. The part remains in
the sleep state as long it is not addressed for a read/write
operation. The conversion result is held indefinitely in a
static shift register while the part is in the sleep state.
The device will not acknowledge an external request during the conversion state. After a conversion is finished,
the device is ready to accept a read/write request. Once
the LTC2493 is addressed for a read operation, the device
begins outputting the conversion result under the control
of the serial clock (SCL). There is no latency in the conversion result. The data output is 32 bits long and contains a
24-bit plus sign conversion result. Data is updated on the
falling edges of SCL allowing the user to reliably latch data
on the rising edge of SCL. A new conversion is initiated
by a stop condition following a valid write operation or an
incomplete read operation. The conversion automatically
begins at the conclusion of a complete read cycle (all 32
bits read out of the device).
Ease of Use
The LTC2493 data output has no latency, filter settling
delay, or redundant data associated with the conversion
cycle. There is a one-to-one correspondence between the
conversion and the output data. Therefore, multiplexing
multiple analog inputs is straightforward. Each conversion, immediately following a newly selected input or
mode, is valid and accurate to the full specifications of
the device.
POWER-ON RESET
DEFAULT CONFIGURATION:
IN+ = CH0, IN– = CH1
50Hz/60Hz REJECTION
1X OUTPUT
CONVERSION
SLEEP
NO
ACKNOWLEDGE
YES
DATA OUTPUT/INPUT
NO
STOP
OR READ
32 BITS
YES
2493 F01
Figure 1. State Transition Table
The LTC2493 automatically performs offset and full-scale
calibration every conversion cycle independent of the input
channel selected. This calibration is transparent to the user
and has no effect on the operation cycle described above.
The advantage of continuous calibration is extreme stability
of offset and full-scale readings with respect to time, supply
voltage variation, input channel, and temperature drift.
Easy Drive Input Current Cancellation
The LTC2493 combines a high precision, delta-sigma ADC
with an automatic, differential, input current cancellation
front end. A proprietary front end passive sampling network
transparently removes the differential input current. This
enables external RC networks and high impedance sensors to directly interface to the LTC2493 without external
2493fa
13
LTC2493
Applications Information
amplifiers. The remaining common mode input current
is eliminated by either balancing the differential input impedances or setting the common mode input equal to the
common mode reference (see the Automatic Differential
Input Current Cancellation section). This unique architecture does not require on-chip buffers, thereby enabling
signals to swing beyond ground and VCC. Moreover, the
cancellation does not interfere with the transparent offset
and full-scale auto-calibration and the absolute accuracy
(full scale + offset + linearity + drift) is maintained even
with external RC networks.
Power-Up Sequence
The LTC2493 automatically enters an internal reset state
when the power supply voltage, VCC, drops below approximately 2.0V. This feature guarantees the integrity of
the conversion result and input channel selection.
When VCC rises above this threshold, the converter creates
an internal power-on-reset (POR) signal with a duration
of approximately 4ms. The POR signal clears all internal
registers. The conversion immediately following a POR
cycle is performed on the input channel IN+ = CH0, IN – =
CH1 with simultaneous 50Hz/60Hz rejection and 1x output
rate. The first conversion following a POR cycle is accurate
within the specification of the device if the power supply
voltage is restored to (2.7V to 5.5V) before the end of the
POR interval. A new input channel, rejection mode, speed
mode, or temperature selection can be programmed into
the device during this first data input/output cycle.
Reference Voltage Range
This converter accepts a truly differential external reference
voltage. The absolute/common mode voltage range for the
REF+ and REF – pins covers the entire operating range of
the device (GND to VCC). For correct converter operation,
VREF must be positive (REF+ > REF –).
The LTC2493 differential reference input range is 0.1V to
VCC. For the simplest operation, REF+ can be shorted to
VCC and REF – can be shorted to GND. The converter output noise is determined by the thermal noise of the front
end circuits and, as such, its value in nanovolts is nearly
constant with reference voltage. A decrease in reference
voltage will not significantly improve the converter’s effective resolution. On the other hand, a decreased reference
will improve the converter’s overall INL performance.
Input Voltage Range
The analog inputs are truly differential with an absolute,
common mode range for the CH0-CH3 and COM input pins
extending from GND – 0.3V to VCC + 0.3V. Outside these
limits, the ESD protection devices begin to turn on and
the errors due to input leakage current increase rapidly.
Within these limits, the LTC2493 converts the bipolar
differential input signal VIN = IN+ – IN– (where IN+ and
IN – are the selected input channels), from –FS = –0.5 • VREF
to +FS = 0.5 • VREF where VREF = REF+ - REF–. Outside
this range, the converter indicates the overrange or the
underrange condition using distinct output codes (see
Table 1).
In order to limit any fault current, resistors of up to 5kW
may be added in series with the input. The effect of series
resistance on the converter accuracy can be evaluated from
the curves presented in the Input Current/Reference Current sections. In addition, series resistors will introduce a
temperature dependent error due to input leakage current.
A 1nA input leakage current will develop a 1ppm offset
error on a 5k resistor if VREF = 5V. This error has a very
strong temperature dependency.
I2C INTERFACE
The LTC2493 communicates through an I2C interface. The
I2C interface is a 2-wire open-drain interface supporting
multiple devices and multiple masters on a single bus. The
connected devices can only pull the data line (SDA) low
and can never drive it high. SDA is required to be externally
2493fa
14
LTC2493
Applications Information
connected to the supply through a pull-up resistor. When
the data line is not being driven, it is high. Data on the
I2C bus can be transferred at rates up to 100kbits/s in the
standard mode and up to 400kbits/s in the fast mode.
Each device on the I2C bus is recognized by a unique
address stored in that device and can operate either as a
transmitter or receiver, depending on the function of the
device. In addition to transmitters and receivers, devices
can also be considered as masters or slaves when performing data transfers. A master is the device which initiates a
data transfer on the bus and generates the clock signals
to permit that transfer. Devices addressed by the master
are considered a slave.
The LTC2493 can only be addressed as a slave. Once
addressed, it can receive configuration bits (channel
selection, rejection mode, speed mode) or transmit the
last conversion result. The serial clock line, SCL, is always
an input to the LTC2493 and the serial data line SDA is
bidirectional. The device supports the standard mode and
the fast mode for data transfer speeds up to 400kbits/s.
Figure 2 shows the definition of the I2C timing.
The Start and Stop Conditions
A Start (S) condition is generated by transitioning SDA from
high to low while SCL is high. The bus is considered to be
busy after the Start condition. When the data transfer is
finished, a Stop (P) condition is generated by transitioning
SDA from low to high while SCL is high. The bus is free
after a Stop is generated. Start and Stop conditions are
always generated by the master.
When the bus is in use, it stays busy if a Repeated Start
(Sr) is generated instead of a Stop condition. The repeated
Start timing is functionally identical to the Start and is
used for writing and reading from the device before the
initiation of a new conversion.
Data Transferring
After the Start condition, the I2C bus is busy and data
transfer can begin between the master and the addressed
slave. Data is transferred over the bus in groups of nine
bits, one byte followed by one acknowledge (ACK) bit.
The master releases the SDA line during the ninth SCL
clock cycle. The slave device can issue an ACK by pulling
SDA low or issue a Not Acknowledge (NAK) by leaving
the SDA line high impedance (the external pull-up resistor
will hold the line high). Change of data only occurs while
the clock line (SCL) is low.
DATA FORMAT
After a Start condition, the master sends a 7-bit address
followed by a read/write (R/W) bit. The R/W bit is 1 for
a read request and 0 for a write request. If the 7-bit address matches the hard wired LTC2493’s address (one of
9 pin-selectable addresses) the device is selected. When
the device is addressed during the conversion state, it will
not acknowledge R/W requests and will issue a NAK by
leaving the SDA line high. If the conversion is complete,
the LTC2493 issues an ACK by pulling the SDA line low.
The LTC2493 has two registers. The output register (32
bits long) contains the last conversion result. The input
register (16 bits long) sets the input channel, selects the
temperature sensor, rejection mode, and speed mode.
SDA
tLOW
tf
tSU(DAT)
tr
tHD(SDA)
tf
tSP
tBUF
tr
SCL
S
tHD(SDA)
tHD(DAT)
tHIGH
tSU(STA)
Sr
tSU(STO)
P
S
2493 F02
Figure 2. Definition of Timing for Fast/Standard Mode Devices on the I2C Bus
2493fa
15
LTC2493
Applications Information
DATA OUTPUT FORMAT
binary two’s, complement format. The remaining six bits
are sub LSBs below the 24-bit level.
The output register contains the last conversion result.
After each conversion is completed, the device automatically enters the sleep state where the supply current is
reduced to 1µA. When the LTC2493 is addressed for a read
operation, it acknowledges (by pulling SDA low) and acts
as a transmitter. The master/receiver can read up to four
bytes from the LTC2493. After a complete read operation
(4 bytes), a new conversion is initiated. The device will
NAK subsequent read operations while a conversion is
being performed.
As long as the voltage on the selected input channels (IN+
and IN–) remains between –0.3V and VCC + 0.3V (absolute
maximum operating range) a conversion result is generated for any differential input voltage VIN from –FS = –0.5
• VREF to +FS = 0.5 • VREF . For differential input voltages
greater than +FS, the conversion result is clamped to the
value corresponding to +FS. For differential input voltages
below –FS, the conversion result is clamped to the value
–FS – 1LSB.
The data output stream is 32 bits long and is shifted out
on the falling edges of SCL (see Figure 3a). The first bit
is the conversion result sign bit (SIG) (see Tables 1 and
2). This bit is high if VIN ≥ 0 and low if VIN < 0 (where VIN
corresponds to the selected input signal IN+ – IN–). The
second bit is the most significant bit (MSB) of the result.
The first two bits (SIG and MSB) can be used to indicate
over and under range conditions (see Table 2). If both bits
are HIGH, the differential input voltage is equal to or above
+FS. If both bits are set low, the input voltage is below –FS.
The function of these bits is summarized in Table 2. The
24 bits following the MSB bit are the conversion result in
Table 2. LTC2493 Status Bits
Bit 31
SIG
Bit 30
MSB
VIN ≥ FS
1
1
0V ≤ VIN < FS
1
0
–FS ≤ VIN < 0V
0
1
VIN < –FS
0
0
Input Range
INPUT DATA FORMAT
The serial input word to the LTC2493 is 13 bits long and
is written into the device input register in two 8-bit words.
Table 1. Output Data Format
Differential Input Voltage
VIN*
Bit 31
SIG
Bit 30
MSB
Bit 29
Bit 28
Bit 27
…
Bit 6
LSB
Bits 5-0
Sub LSBs***
VIN* ≥ FS**
1
1
0
0
0
…
0
00000
FS** – 1LSB
1
0
1
1
1
…
1
XXXXX
0.5 • FS**
1
0
1
0
0
…
0
XXXXX
0.5 • FS** – 1LSB
1
0
0
1
1
…
1
XXXXX
0
1
0
0
0
0
…
0
XXXXX
–1LSB
0
1
1
1
1
…
1
XXXXX
–0.5 • FS**
0
1
1
0
0
…
0
XXXXX
–0.5 • FS** – 1LSB
0
1
0
1
1
…
1
XXXXX
–FS**
0
1
0
0
0
…
0
XXXXX
VIN* < –FS**
0
0
1
1
1
…
1
11111
*The differential input voltage VIN = IN+ – IN–. **The full-scale voltage FS = 0.5 • VREF .
*** Sub LSBs are below the 24-bit level. They may be included in averaging, or discarded without loss of resolution.
2493fa
16
LTC2493
Applications Information
The first word (SGL, ODD, A2, A1, A0) is used to select the
input channel. The second word of data (IM, FA, FB, SPD)
is used to select the frequency rejection, speed mode (1x,
2x), and temperature measurement.
If the first three bits shifted into the device are 101, then
the next five bits select the input channel for the next
conversion cycle (see Table 3).
The first input bit (SGL) following the 101 sequence determines if the input selection is differential (SGL = 0) or
single-ended (SGL = 1). For SGL = 0, two adjacent channels can be selected to form a differential input. For SGL
= 1, one of 4 channels is selected as the positive input.
The negative input is COM for all single-ended operations.
The remaining four bits (ODD, A2, A1, A0) determine
which channel(s) is/are selected and the polarity (for a
differential input).
After power-up, the device initiates an internal reset cycle
which sets the input channel to CH0-CH1 (IN+ = CH0, IN– =
CH1), the frequency rejection to simultaneous 50Hz/60Hz,
and 1x output rate (auto-calibration enabled). The first
conversion automatically begins at power-up using this
default configuration. Once the conversion is complete,
up to two words may be written into the device.
The first three bits of the first input word consist of two
preamble bits and one enable bit. Valid settings for these
three bits are 000, 100, and 101. Other combinations
should be avoided.
Once the first word is written into the device, a second
word may be input in order to select a configuration mode.
The first bit of the second word is the enable bit for the
conversion configuration (EN2). If this bit is set to 0, then
the next conversion is performed using the previously
selected converter configuration.
If the first three bits are 000 or 100, the following data
is ignored (don’t care) and the previously selected input
channel remains valid for the next conversion.
1
SCL
…
7
8
9
1
2
…
SIG
MSB
9
1
2
3
4
5
6
7
8
9
SDA
7-BIT
ADDRESS
R
D31
ACK BY
LTC2493
START BY
MASTER
LSB
ACK BY
MASTER
NAK BY
MASTER
SUB LSBs
SLEEP
DATA OUTPUT
2493 F03a
Figure 3a. Timing Diagram for Reading from the LTC2493
1
SCL
2
…
7
8
9
1
2
3
4
5
6
7
9
8
1
2
3
4
5
6
7
8
9
SDA
7-BIT ADDRESS
1
W
ACK BY
LTC2493
START BY
MASTER
SLEEP
0
EN
SGL ODD
A2
A1
A0
EN2
ACK BY
LTC2493
IM
FA
FB
SPD
(OPTIONAL 2ND BYTE)
DATA INPUT
ACK BY
LTC2493
2493 F03b
Figure 3b. Timing Diagram for Writing to the LTC2493
2493fa
17
LTC2493
Applications Information
set the rejection frequency. The final bit (SPD) is used to
select either the 1x output rate if SPD = 0 (auto-calibration
is enabled and the offset is continuously calibrated and
removed from the final conversion result) or the 2x output
rate if SPD = 1 (offset calibration disabled, multiplexing
output rates up to 15Hz with no latency). When IM = 1
(temperature measurement) SPD will be ignored and the
device will operate in 1x mode.
Table 3 Channel Selection
MUX ADDRESS
SGL
ODD/
SIGN
A2
A1
CHANNEL SELECTION
A0
0
1
IN+
IN–
*0
0
0
0
0
0
0
0
0
1
0
1
0
0
0
0
1
0
0
1
1
0
0
0
0
1
0
0
0
1
1
1
0
0
0
1
1
0
0
IN–
2
3
IN+
IN–
IN–
IN+
COM
IN+
IN+
IN–
IN+
The configuration remains valid until a new input word with
EN = 1 (the first three bits are 101 for the first word) and EN2
= 1 (for the second write byte) is shifted into the device.
IN–
IN+
IN–
IN+
1
IN–
*Default at power up
Rejection Mode (FA, FB)
The second set of configuration data can be loaded into
the device by setting EN2 = 1 (see Table 4). The first bit
(IM) is used to select the internal temperature sensor. If
IM = 1, the following conversion will be performed on
the internal temperature sensor rather than the selected
input channel. The next two bits (FA and FB) are used to
The LTC2493 includes a high accuracy on-chip oscillator
with no required external components. Coupled with an
integrated fourth order digital low pass filter, the LTC2493
rejects line frequency noise. In the default mode, the
LTC2493 simultaneously rejects 50Hz and 60Hz by at least
87dB. If more rejection is required, the LTC2493 can be
configured to reject 50Hz or 60Hz to better than 110dB.
Table 4. Converter Configuration
1
0
EN
SGL
ODD
A2
A1
A0
EN2
IM
FA
FB
SPD
CONVERTER CONFIGURATION
1
0
0
X
X
X
X
X
X
X
X
X
X
Keep Previous
1
0
1
X
X
X
X
X
0
X
X
X
X
Keep Previous
0
0
1
X
X
X
X
X
X
X
X
X
X
Keep Previous
1
0
1
X
X
X
X
X
1
0
0
0
0
External Input (See Table 3)
50Hz/60Hz Rejection, 1x
1
0
1
X
X
X
X
X
1
0
0
1
0
External Input (See Table 3)
50Hz Rejection, 1x
1
0
1
X
X
X
X
X
1
0
1
0
0
External Input (See Table 3)
60Hz Rejection, 1x
1
0
1
X
X
X
X
X
1
0
0
0
1
External Input (See Table 3)
50Hz/60Hz Rejection, 2x
1
0
1
X
X
X
X
X
1
0
0
1
1
External Input (See Table 3)
50Hz Rejection, 2x
1
0
1
X
X
X
X
X
1
0
1
0
1
External Input (See Table 3)
60Hz Rejection, 2x
1
0
1
X
X
X
X
X
1
1
0
0
X
Measure Temperature
50Hz/60Hz Rejection, 1x
1
0
1
X
X
X
X
X
1
1
0
1
X
Measure Temperature
50Hz Rejection, 1x
1
0
1
X
X
X
X
X
1
1
1
0
X
Measure Temperature
60Hz Rejection, 1x
1
0
1
X
X
X
X
X
1
X
1
1
X
Reserved, Do Not Use
2493fa
18
LTC2493
Applications Information
Speed Mode (SPD)
Every conversion cycle, two conversions are combined
to remove the offset (default mode). This result is free
from offset and drift. In applications where the offset is
not critical, the auto-calibration feature can be disabled
with the benefit of twice the output rate.
While operating in the 2x mode (SPD = 1), the linearity
and full-scale errors are unchanged from the 1x mode
performance. In both the 1x and 2x mode there is no
latency. This enables input steps or multiplexer changes
to settle in a single conversion cycle, easing system overhead and increasing the effective conversion rate. During
temperature measurements, the 1x mode is always used
independent of the value of SPD.
Temperature Sensor
The LTC2493 includes an integrated temperature sensor. The temperature sensor is selected by setting
IM = 1. The ADC internally connects to the temperature
sensor and performs a conversion.
The digital output is proportional to the absolute temperature of the device. This feature allows the converter
to perform cold junction compensation for external
thermocouples or continuously remove the temperature
effects of external sensors.
The internal temperature sensor output is 28mV at 27ºC
(300ºK), with a slope of 93.5µV/ºC independent of VREF
(see Figures 4 and 5). Slope calibration is not required if
the reference voltage (VREF) is known. A 5V reference has
a slope of 314 LSBs24/ºC. The temperature is calculated
from the output code (where DATAOUT24 is the decimal
representation of the 24-bit result) for a 5V reference using
the following formula:
TK =
DATAOUT24
in Kelvin
314
If a different value of VREF is used, the temperature
output is:
DATAOUT24 • VREF
TK =
in Kelvin
1570
If the value of VREF is not known, the slope is determined
by measuring the temperature sensor at a known temperature TN (in K) and using the following formula:
SLOPE =
This value of slope can be used to calculate further temperature readings using:
TK =
DATAOUT24
SLOPE
All Kelvin temperature readings can be converted to TC
(ºC) using the fundamental equation:
TC = TK – 273
140000
5
VCC = 5V
VREF = 5V
120000 SLOPE = 314 LSB /K
24
4
ABSOLUTE ERROR (°C)
3
DATAOUT24
100000
80000
60000
40000
2
1
0
–1
–2
–3
20000
0
DATAOUT24
TN
–4
0
100
200
300
TEMPERATURE (K)
400
2493 F04
Figure 4. Internal PTAT Digital Output vs Temperature
–5
–55
–30
–5
20
45
70
TEMPERATURE (°C)
95
120
2493 F05
Figure 5. Absolute Temperature Error
2493fa
19
LTC2493
Applications Information
Initiating a New Conversion
Table 5. Address Assignment
When the LTC2493 finishes a conversion, it automatically
enters the sleep state. Once in the sleep state, the device is
ready for a read operation. After the device acknowledges
a read request, the device exits the sleep state and enters
the data output state. The data output state concludes
and the LTC2493 starts a new conversion once a Stop
condition is issued by the master or all 32 bits of data are
read out of the device.
During the data read cycle, a Stop command may be issued
by the master controller in order to start a new conversion
and abort the data transfer. This Stop command must be
issued during the ninth clock cycle of a byte read when
the bus is free (the ACK/NAK cycle).
LTC2493 Address
The LTC2493 has two address pins (CA0, CA1). Each may
be tied high, low, or left floating enabling one of 9 possible
addresses (see Table 5).
In addition to the configurable addresses listed in Table
5, the LTC2493 also contains a global address (1110111)
which may be used for synchronizing multiple LTC2493s or
other LTC24XX delta-sigma I2C devices (see Synchronizing
Multiple LTC2493s with a Global Address Call section).
Operation Sequence
The LTC2493 acts as a transmitter or receiver, as shown
in Figure 6. The device may be programmed to perform
several functions. These include input channel selection,
S
R/W
7-BIT ADDRESS
CONVERSION
SLEEP
ACK
DATA
CA1
CA0
ADDRESS
LOW
LOW
0010100
LOW
HIGH
0010110
LOW
FLOAT
0010101
HIGH
LOW
0100110
HIGH
HIGH
0110100
HIGH
FLOAT
0100111
FLOAT
LOW
0010111
FLOAT
HIGH
0100101
FLOAT
FLOAT
0100100
measure the internal temperature, selecting the line frequency rejection (50Hz, 60Hz, or simultaneous 50Hz and
60Hz) and a 2x speed mode.
Continuous Read
In applications where the input channel/configuration does
not need to change for each cycle, the conversion can be
continuously performed and read without a write cycle
(see Figure 7). The configuration/input channel remains
unchanged from the last value written into the device. If
the device has not been written to since power up, the
configuration is set to the default value. At the end of a
read operation, a new conversion automatically begins.
At the conclusion of the conversion cycle, the next result
may be read using the method described above. If the
conversion cycle is not concluded and a valid address
selects the device, the LTC2493 generates a NAK signal
indicating the conversion cycle is in progress.
Sr
DATA TRANSFERRING
DATA INPUT/OUTPUT
P
CONVERSION
2493 F05
Figure 6. Conversion Sequence
2493fa
20
LTC2493
Applications Information
Continuous Read/Write
and 60Hz) is used but the channel is changed, a Stop or
Repeated Start may be issued after the first byte (channel
selection data) is written into the device.
Once the conversion cycle is concluded, the LTC2493 can
be written to and then read from using the Repeated Start
(Sr) command.
Discarding a Conversion Result and Initiating a New
Conversion with Optional Write
Figure 8 shows a cycle which begins with a data Write, a
repeated Start, followed by a Read and concluded with a
Stop command. The following conversion begins after all
32 bits are read out of the device or after a Stop command.
The following conversion will be performed using the
newly programmed data. In cases where the same speed
(1x/2x mode) and rejection frequency (50Hz, 60Hz, 50Hz
S
7-BIT ADDRESS
CONVERSION
R ACK
SLEEP
READ
At the conclusion of a conversion cycle, a write cycle
can be initiated. Once the write cycle is acknowledged, a
Stop command will start a new conversion. If a new input
channel or conversion configuration is required, this data
can be written into the device and a Stop command will
initiate the next conversion (see Figure 9).
P
S
DATA INPUT
7-BIT ADDRESS
CONVERSION
R ACK
SLEEP
READ
P
DATA OUTPUT
CONVERSION
2493 F07
Figure 7. Consecutive Reading with the Same Input/Configuration
S
7-BIT ADDRESS
CONVERSION
W ACK
SLEEP
WRITE
Sr
DATA INPUT
7-BIT ADDRESS
R ACK
ADDRESS
READ
DATA OUTPUT
P
CONVERSION
2493 F08
Figure 8. Write, Read, Start Conversion
S
7-BIT ADDRESS
CONVERSION
W ACK
SLEEP
WRITE (OPTIONAL)
DATA INPUT
P
CONVERSION
2493 F09
Figure 9. Start a New Conversion Without Reading Old Conversion Result
2493fa
21
LTC2493
Applications Information
Synchronizing Multiple LTC2493s with a Global
Address Call
to synchronize multiple converters without changing
the channel or configuration, a Stop may be issued after
acknowledgement of the global write command. Global
read commands are not allowed and the converters will
NAK a global read request.
In applications where several LTC2493s (or other I2C
delta-sigma ADCs from Linear Technology Corporation)
are used on the same I2C bus, all converters can be synchronized through the use of a global address call. Prior
to issuing the global address call, all converters must have
completed a conversion cycle. The master then issues a
Start, followed by the global address 1110111, and a write
request. All converters will be selected and acknowledge
the request. The master then sends a write byte (optional)
followed by the Stop command. This will update the channel selection (optional) converter configuration (optional)
and simultaneously initiate a start of conversion for all
delta-sigma ADCs on the bus (see Figure 10). In order
Driving the Input and Reference
The input and reference pins of the LTC2493 are connected
directly to a switched capacitor network. Depending on
the relationship between the differential input voltage and
the differential reference voltage, these capacitors are
switched between these four pins. Each time a capacitor
is switched between two of these pins, a small amount
of charge is transferred. A simplified equivalent circuit is
shown in Figure 11.
SCL
SDA
LTC2493
S
LTC2493
GLOBAL ADDRESS
W ACK
ALL LTC2493s IN SLEEP
…
LTC2493
WRITE (OPTIONAL)
P
CONVERSION OF ALL LTC2493s
DATA INPUT
2493 F10
Figure 10. Synchronize Multiple LTC2493s with a Global Address Call
IIN
+
IN+
INPUT
MULTIPLEXER
100Ω
INTERNAL
SWITCH
NETWORK
( )
I IN+
10kΩ
(
I REF +
IIN–
IN–
AVG
100Ω
SWITCHING FREQUENCY
fSW = 123kHz INTERNAL OSCILLATOR
fSW = 0.4 • fEOSC EXTERNAL OSCILLATOR
CEQ
12µF
0.5 • REQ
(
1.5VREF + VREF(CM) – VIN(CM)
0.5 • REQ
10kΩ
 REF + – REF −
VREF(CM) = 

2
)–
VIN2
VREF • REQ



VIN = IN+ − IN− , WHERE IN+ AND IN− ARE THE SELECTED INPUT CHANNELS
 IN+ – IN− 
VIN(CM) = 



2
REQ = 2.71MW INTERNAL OSCILLATOR 60Hz MODE
10kΩ
2493 F11a
REQ = 2.98MW INTERNAL OSCILLATOR 50Hz/60Hz MODE
(
)
REQ = 0.833 • 1012 /fEOSC EXTERNAL OSCILLATOR
Figure 11. Equivalent Analog Input Circuit
22
VIN(CM) − VREF(CM)
=
VREF = REF + − REF −
IREF–
REF–
AVG
≈
AVG
where :
10kΩ
IREF+
REF+
)
( )
= I IN–
2493fa
LTC2493
Applications Information
When using the LTC2493’s internal oscillator, the input
capacitor array is switched at 123kHz. The effect of the
charge transfer depends on the circuitry driving the input/reference pins. If the total external RC time constant
is less than 580ns the errors introduced by the sampling
process are negligible since complete settling occurs.
Typically, the reference inputs are driven from a low
impedance source. In this case, complete settling occurs
even with large external bypass capacitors. The inputs
(CH0-CH3, COM), on the other hand, are typically driven
from larger source resistances. Source resistances up
to 10k may interface directly to the LTC2493 and settle
completely; however, the addition of external capacitors
at the input terminals in order to filter unwanted noise
(antialiasing) results in incomplete settling.
Automatic Differential Input Current Cancellation
In applications where the sensor output impedance is
low (up to 10kW with no external bypass capacitor or up
to 500W with 0.001µF bypass), complete settling of the
input occurs. In this case, no errors are introduced and
direct digitization is possible.
For many applications, the sensor output impedance
combined with external input bypass capacitors produces
RC time constants much greater than the 580ns required
for 1ppm accuracy. For example, a 10kW bridge driving a
0.1µF capacitor has a time constant an order of magnitude
greater than the required maximum.
The LTC2493 uses a proprietary switching algorithm
that forces the average differential input current to zero
independent of external settling errors. This allows direct
digitization of high impedance sensors without the need
for buffers.
The switching algorithm forces the average input current
on the positive input (IIN+) to be equal to the average input
current on the negative input (IIN–). Over the complete
conversion cycle, the average differential input current
(IIN+ – IIN–) is zero. While the differential input current is
zero, the common mode input current (IIN+ + IIN–)/2 is
proportional to the difference between the common mode
input voltage (VIN(CM)) and the common mode reference
voltage (VREF(CM)).
In applications where the input common mode voltage is
equal to the reference common mode voltage, as in the
case of a balanced bridge, both the differential and common mode input current are zero. The accuracy of the
converter is not compromised by settling errors.
In applications where the input common mode voltage is
constant but different from the reference common mode
voltage, the differential input current remains zero while
the common mode input current is proportional to the
difference between VIN(CM) and VREF(CM). For a reference
common mode voltage of 2.5V and an input common mode
of 1.5V, the common mode input current is approximately
0.74µA (in simultaneous 50Hz/60Hz rejection mode). This
common mode input current does not degrade the accuracy
if the source impedances tied to IN+ and IN– are matched.
Mismatches in source impedance lead to a fixed offset
error but do not effect the linearity or full-scale reading. A
1% mismatch in a 1kW source resistance leads to a 74µV
shift in offset voltage.
In applications where the common mode input voltage
varies as a function of the input signal level (single-ended
type sensors), the common mode input current varies
proportionally with input voltage. For the case of balanced
input impedances, the common mode input current effects
are rejected by the large CMRR of the LTC2493, leading
to little degradation in accuracy. Mismatches in source
impedances lead to gain errors proportional to the difference between the common mode input and common
mode reference. 1% mismatches in 1k source resistances
lead to gain errors on the order of 15ppm. Based on the
stability of the internal sampling capacitors and the accuracy of the internal oscillator, a one-time calibration will
remove this error.
In addition to the input sampling current, the input ESD
protection diodes have a temperature dependent leakage
current. This current, nominally 1nA (±10nA max), results
in a small offset shift. A 1k source resistance will create a
1µV typical and a 10µV maximum offset voltage.
2493fa
23
LTC2493
Applications Information
Reference Current
Similar to the analog inputs, the LTC2493 samples the
differential reference pins (REF+ and REF–) transferring
small amounts of charge to and from these pins, thus
producing a dynamic reference current. If incomplete settling occurs (as a function the reference source resistance
and reference bypass capacitance) linearity and gain errors
are introduced.
For relatively small values of external reference capacitance
(CREF < 1nF), the voltage on the sampling capacitor settles
90
60
50
0
CREF = 0.01µF
CREF = 0.001µF
CREF = 100pF
CREF = 0pF
40
30
20
–20
–30
–40
–50
VCC = 5V
–60 VREF = 5V
V + = 1.25V
–70 VIN– = 3.75V
IN
–80 FO = GND
TA = 25°C
–90
10
0
10
0
0
10
1k
100
RSOURCE (Ω)
10k
100k
2493 F12
Figure 12. +FS Error vs RSOURCE at VREF (Small CREF)
500
VCC = 5V
VREF = 5V
VIN+ = 3.75V
VIN– = 1.25V
FO = GND
TA = 25°C
+FS ERROR (ppm)
400
300
2493 F13
–100
CREF = 0.1µF
CREF = 0.01µF
–200
CREF = 1µF, 10µF
–300
VCC = 5V
VREF = 5V
VIN+ = 1.25V
VIN– = 3.75V
FO = GND
TA = 25°C
–400
100
200
100k
0
CREF = 0.01µF
0
10k
CREF = 1µF, 10µF
200
0
1k
100
RSOURCE (Ω)
Figure 13. –FS Error vs RSOURCE at VREF (Small CREF)
–FS ERROR (ppm)
–10
CREF = 0.01µF
CREF = 0.001µF
CREF = 100pF
CREF = 0pF
–10
–FS ERROR (ppm)
+FS ERROR (ppm)
70
In cases where large bypass capacitors are required on
the reference inputs (CREF > .01µF), full-scale and linearity errors are proportional to the value of the reference
resistance. Every ohm of reference resistance produces
a full-scale error of approximately 0.5ppm (while operating in simultaneous 50Hz/60Hz mode (see Figures 14
and 15)). If the input common mode voltage is equal to
10
VCC = 5V
VREF = 5V
VIN+ = 3.75V
VIN– = 1.25V
FO = GND
TA = 25°C
80
for reference impedances of many kW (if CREF = 100pF up
to 10kW will not degrade the performance (see Figures
12 and 13)).
600
400
RSOURCE (Ω)
800
1000
2493 F14
Figure 14. +FS Error vs RSOURCE at VREF (Large CREF)
–500
0
200
CREF = 0.1µF
600
400
RSOURCE (Ω)
800
1000
2493 F15
Figure 15. –FS Error vs RSOURCE at VREF (Large CREF)
2493fa
24
LTC2493
Applications Information
In addition to the reference sampling charge, the reference
ESD protection diodes have a temperature dependent leakage current. This leakage current, nominally 1nA (±10nA
max) results in a small gain error. A 100W reference
resistance will create a 0.5µV full-scale error.
Normal Mode Rejection and Antialiasing
One of the advantages delta-sigma ADCs offer over
conventional ADCs is on-chip digital filtering. Combined
with a large oversample ratio, the LTC2493 significantly
simplifies antialiasing filter requirements. Additionally,
the input current cancellation feature allows external low
pass filtering without degrading the DC performance of
the device.
The SINC4 digital filter provides excellent normal mode
rejection at all frequencies except DC and integer multiples
of the modulator sampling frequency (fS) (see Figures
17 and 18). The modulator sampling frequency is fS =
15,360Hz while operating with its internal oscillator and
fS = fEOSC/20 when operating with an external oscillator
of frequency fEOSC .
0
INPUT NORMAL MODE REJECTION (dB)
the reference common mode voltage, a linearity error of
approximately 0.67ppm per 100W of reference resistance
results (see Figure 16). In applications where the input
and reference common mode voltages are different, the
errors increase. A 1V difference in between common mode
input and common mode reference results in a 6.7ppm
INL error for every 100W of reference resistance.
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
–110
–120
0 fS 2fS 3fS 4fS 5fS 6fS 7fS 8fS 9fS 10fS11fS12fS
DIFFERENTIAL INPUT SIGNAL FREQUENCY (Hz)
2493 F17
Figure 17. Input Normal Mode Rejection, Internal
Oscillator and 50Hz Rejection Mode
VCC = 5V
8 VREF = 5V
VIN(CM) = 2.5V
6 T = 25°C
A
4 CREF = 10µF
0
R = 1k
2
R = 500Ω
0
R = 100Ω
–2
–4
–6
–8
–10
– 0.5
– 0.3
0.1
– 0.1
VIN/VREF
0.3
0.5
2493 F16
Figure 16. INL vs Differential Input Voltage and
Reference Source Resistance for CREF > 1µF
INPUT NORMAL MODE REJECTION (dB)
INL (ppm OF VREF)
10
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
–110
–120
0 fS 2fS 3fS 4fS 5fS 6fS 7fS 8fS 9fS 10fS
DIFFERENTIAL INPUT SIGNAL FREQUENCY (Hz)
2493 F18
Figure 18. Input Normal Mode Rejection, Internal
Oscillator and 60Hz Rejection Mode
2493fa
25
LTC2493
Applications Information
When using the internal oscillator, the LTC2493 is designed
to reject line frequencies. As shown in Figure 19, rejection nulls occur at multiples of frequency fN, where fN is
determined by the input control bits FA and FB (fN = 50Hz
or 60Hz or 55Hz for simultaneous rejection). Multiples of
the modulator sampling rate (fS = fN • 256) only reject noise
to 15dB (see Figure 20); if noise sources are present at
these frequencies antialiasing will reduce their effects.
The user can expect to achieve this level of performance
using the internal oscillator, as shown in Figures 21, 22,
and 23. Measured values of normal mode rejection are
shown superimposed over the theoretical values in all
three rejection modes.
INPUT NORMAL MODE REJECTION (dB)
0
Traditional high order delta-sigma modulators suffer
from potential instabilities at large input signal levels.
The proprietary architecture used for the LTC2493 third
order modulator resolves this problem and guarantees
stability with input signals 150% of full scale. In many
industrial applications, it is not uncommon to have microvolt level signals superimposed over unwanted error
sources with several volts if peak-to-peak noise. Figures
24 and 25 show measurement results for the rejection
of a 7.5V peak-to-peak noise source (150% of full scale)
applied to the LTC2493. These curves show that the rejection performance is maintained even in extremely noisy
environments.
fN = fEOSC/5120
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
–110
–120
0
fN
2fN 3fN 4fN 5fN 6fN 7fN
INPUT SIGNAL FREQUENCY (Hz)
8fN
2493 F19
Figure 19. Input Normal Mode Rejection at DC
INPUT NORMAL MODE REJECTION (dB)
0
–10
fN = fEOSC/5120
–20
–30
–40
–50
–60
–70
–80
–90
–100
–110
–120
250fN 252fN 254fN 256fN 258fN 260fN 262fN
INPUT SIGNAL FREQUENCY (Hz)
2493 F20
Figure 20. Input Normal Mode Rejection at fS = 256 • fN
2493fa
26
LTC2493
Applications Information
MEASURED DATA
CALCULATED DATA
–20
–40
VCC = 5V
VREF = 5V
VIN(CM) = 2.5V
VIN(P-P) = 5V
TA = 25°C
– 60
–80
–100
–120
0
15
30
45
60
75
0
NORMAL MODE REJECTION (dB)
NORMAL MODE REJECTION (dB)
0
–40
VCC = 5V
VREF = 5V
VIN(CM) = 2.5V
VIN(P-P) = 5V
TA = 25°C
– 60
–80
–100
–120
90 105 120 135 150 165 180 195 210 225 240
INPUT FREQUENCY (Hz)
MEASURED DATA
CALCULATED DATA
–20
0
12.5 25 37.5 50 62.5 75 87.5 100 112.5 125 137.5 150 162.5 175 187.5 200
INPUT FREQUENCY (Hz)
2493 F21
NORMAL MODE REJECTION (dB)
0
MEASURED DATA
CALCULATED DATA
–20
–40
VCC = 5V
VREF = 5V
VIN(CM) = 2.5V
VIN(P-P) = 5V
TA = 25°C
– 60
–80
–100
–120
0
12.5 25 37.5 50 62.5 75 87.5 100 112.5 125 137.5 150 162.5 175 187.5 200
INPUT FREQUENCY (Hz)
Figure 22. Input Normal Mode Rejection vs Input Frequency with
Input Perturbation of 100% (50Hz Notch)
0
NORMAL MODE REJECTION (dB)
Figure 21. Input Normal Mode Rejection vs Input Frequency with
Input Perturbation of 100% (60Hz Notch)
2493 F22
VIN(P-P) = 5V
VIN(P-P) = 7.5V
(150% OF FULL SCALE)
–20
VCC = 5V
VREF = 5V
VIN(CM) = 2.5V
TA = 25°C
–40
– 60
–80
–100
–120
0
15
30
45
60
75
90 105 120 135 150 165 180 195 210 225 240
INPUT FREQUENCY (Hz)
2493 F24
2493 F23
Figure 23. Input Normal Mode Rejection vs Input Frequency with
Input Perturbation of 100% (50Hz/60Hz Notch)
Figure 24. Measure Input Normal Mode Rejection vs Input
Frequency with Input Perturbation of 150% (60Hz Notch)
NORMAL MODE REJECTION (dB)
0
VIN(P-P) = 5V
VIN(P-P) = 7.5V
(150% OF FULL SCALE)
–20
VCC = 5V
VREF = 5V
VIN(CM) = 2.5V
TA = 25°C
–40
– 60
–80
–100
–120
0
12.5 25 37.5 50 62.5 75 87.5 100 112.5 125 137.5 150 162.5 175 187.5 200
INPUT FREQUENCY (Hz)
2493 F25
Figure 25. Measure Input Normal Mode Rejection vs Input
Frequency with Input Perturbation of 150% (50Hz Notch)
2493fa
27
LTC2493
Applications Information
Using the 2X speed mode of the LTC2493 alters the
rejection characteristics around DC and multiples of fS.
The device bypasses the offset calibration in order to
increase the output rate. The resulting rejection plots are
shown in Figures 26 and 27. 1x type frequency rejection
can be achieved using the 2x mode by performing a running average of the previoius two conversion results (see
Figure 28).
Output Data Rate
When using its internal oscillator, the LTC2493 produces
up to 15 samples per second (sps) with a notch frequency of
60Hz. The actual output data rate depends upon the length
of the sleep and data output cycles which are controlled
by the user and can be made insignificantly short. When
operating with an external conversion clock (fO connected
to an external oscillator), the LTC2493 output data rate
can be increased. The duration of the conversion cycle is
41036/fEOSC. If fEOSC = 307.2kHz, the converter behaves
as if the internal oscillator is used.
A change in fEOSC results in a proportional change in the
internal notch position. This leads to reduced differential
mode rejection of line frequencies. The common mode
rejection of line frequencies remains unchanged, thus fully
differential input signals with a high degree of symmetry
on both the IN+ and IN – pins will continue to reject line
frequency noise.
An increase in fEOSC also increases the effective dynamic
input and reference current. External RC networks will
continue to have zero differential input current, but the
time required for complete settling (580ns for fEOSC =
307.2kHz) is reduced, proportionally.
Once the external oscillator frequency is increased above
1MHz (a more than 3x increase in output rate) the effectiveness of internal auto calibration circuits begins to degrade.
This results in larger offset errors, full-scale errors, and
decreased resolution, as seen in Figures 29-36.
0
0
–20
–20
INPUT NORMAL REJECTION (dB)
INPUT NORMAL REJECTION (dB)
An increase in fEOSC over the nominal 307.2kHz will translate into a proportional increase in the maximum output
data rate (up to a maximum of 100sps). The increase in
output rate leads to degradation in offset, full-scale error,
and effective resolution as well as a shift in frequency rejection. When using the integrated temperature sensor, the
internal oscillator should be used or an external oscillator
fEOSC = 307.2kHz maximum.
–40
–60
–80
–100
–120
0
fN
2fN 3fN 4fN 5fN 6fN 7fN
INPUT SIGNAL FREQUENCY (fN)
8fN
2493 F26
Figure 26. Input Normal Mode Rejection 2x Speed Mode
–40
–60
–80
–100
–120
248 250 252 254 256 258 260 262 264
INPUT SIGNAL FREQUENCY (fN)
2493 F27
Figure 27. Input Normal Mode Rejection 2x Speed Mode
2493fa
28
LTC2493
Applications Information
50
OFFSET ERROR (ppm OF VREF)
NO AVERAGE
–90
WITH
RUNNING
AVERAGE
–100
–110
–120
–130
30
TA = 85°C
20
10
0
–FS ERROR (ppm OF VREF)
RESOLUTION (BITS)
–2000
–2500
V
= VREF(CM)
–3000 IN(CM)
VCC = VREF = 5V
FO = EXT CLOCK
–3500
0 10 20 30 40 50 60 70 80 90 100
OUTPUT DATA RATE (READINGS/SEC)
20
20
TA = 85°C
16
14
12
10
VIN(CM) = VREF(CM)
VCC = VREF = 5V
VIN = 0V
FO = EXT CLOCK
RES = LOG 2 (VREF/NOISERMS)
0 10 20 30 40 50 60 70 80 90 100
OUTPUT DATA RATE (READINGS/SEC)
RESOLUTION (BITS)
VCC = 5V, VREF = 2.5V
0 10 20 30 40 50 60 70 80 90 100
OUTPUT DATA RATE (READINGS/SEC)
2493 F34
Figure 34. Offset Error vs Output
Data Rate and Temperature
TA = 25°C
14
2493 F33
20
Figure 33. Resolution (INLMAX ≤ 1LSB)
vs Output Data Rate and Temperature
22
VCC = VREF = 5V
22
0
TA = 85°C
VIN(CM) = VREF(CM)
12 VCC = VREF = 5V
FO = EXT CLOCK
RES = LOG 2 (VREF/INLMAX)
10
0 10 20 30 40 50 60 70 80 90 100
OUTPUT DATA RATE (READINGS/SEC)
24
VIN(CM) = VREF(CM)
VIN = 0V
15 FO = EXT CLOCK
TA = 25°C
VCC = VREF = 5V
16
Figure 32. Resolution (NoiseRMS ≤ 1LSB)
vs Output Data Rate and Temperature
20
10
18
2493 F32
2493 F31
OFFSET ERROR (ppm OF VREF)
22
18
Figure 31.–FS Error vs Output Data
Rate and Temperature
–10
2493 F30
TA = 25°C
22
TA = 85°C
0 10 20 30 40 50 60 70 80 90 100
OUTPUT DATA RATE (READINGS/SEC)
Figure 30. +FS Error vs Output Data
Rate and Temperature
24
TA = 25°C
–1500
0
2493 F29
–500
–5
500
Figure 29. Offset Error vs Output Data
Rate and Temperature
0
–1000
TA = 25°C
1000
10 20 30 40 50 60 70 80 90 100
OUTPUT DATA RATE (READINGS/SEC)
2493 F28
Figure 28. Input Normal Mode
Rejection 2x Speed Mode with and
Without Running Averaging
5
1500
0
–10
TA = 85°C
2000
TA = 25°C
60
62
48 50
54 56
58
52
DIFFERENTIAL INPUT SIGNAL FREQUENCY (Hz)
VIN(CM) = VREF(CM)
VCC = VREF = 5V
FO = EXT CLOCK
2500
RESOLUTION (BITS)
–140
40
3000
20
VCC = 5V, VREF = 2.5V
18
16
14 VIN(CM) = VREF(CM)
VIN = 0V
FO = EXT CLOCK
12 T = 25°C
A
RES = LOG 2 (VREF/NOISERMS)
10
0 10 20 30 40 50 60 70 80 90 100
OUTPUT DATA RATE (READINGS/SEC)
RESOLUTION (BITS)
NORMAL MODE REJECTION (dB)
–80
3500
VIN(CM) = VREF(CM)
VCC = VREF = 5V
VIN = 0V
FO = EXT CLOCK
+FS ERROR (ppm OF VREF)
–70
2493 F35
Figure 35. Resolution (NoiseRMS ≤ 1LSB)
vs Output Data Rate and Temperature
18
VCC = VREF = 5V
16
VCC = 5V, VREF = 2.5V
VIN(CM) = VREF(CM)
14
VIN = 0V
REF– = GND
12 FO = EXT CLOCK
TA = 25°C
RES = LOG 2 (VREF/INLMAX)
10
0 10 20 30 40 50 60 70 80 90 100
OUTPUT DATA RATE (READINGS/SEC)
2493 F36
Figure 36. Resolution (INLMAX ≤ 1LSB)
vs Output Data Rate and Temperature
2493fa
29
LTC2493
Applications Information
Easy Drive ADCs Simplify Measurement of High
Impedance Sensors
Delta-Sigma ADCs, with their high accuracy and high noise
immunity, are ideal for directly measuring many types
of sensors. Nevertheless, input sampling currents can
overwhelm high source impedances or low-bandwidth,
micropower signal conditioning circuits. The LTC2493
solves this problem by balancing the input currents, thus
simplifying or eliminating the need for signal conditioning
circuits.
A common application for a delta-sigma ADC is thermistor
measurement. Figure 37 shows two examples of thermistor
digitization benefiting from the Easy Drive technology.
The first circuit (applied to input channels CH0 and CH1)
uses balanced reference resistors in order to balance the
common mode input/reference voltage and balance the
differential input source resistance. If reference resistors
R1 and R4 are exactly equal, the input current is zero and
no errors result. If these resistors have a 1% tolerance,
the maximum error in measured resistance is 1.6Ω due
to a shift in common mode voltage; far less than the 1%
error of the reference resistors themselves. No amplifier
is required, making this an ideal solution in micropower
applications.
Easy Drive also enables very low power, low bandwidth
amplifiers to drive the input to the LTC2493. As shown in
Figure 7, CH2 is driven by the LT1494. The LT1494 has
excellent DC specs for an amplifier with 1.5µA supply
current (the maximum offset voltage is 150µV and the
open loop gain is 100,000). Its 2kHz bandwidth makes
it unsuitable for driving conventional delta sigma ADCs.
Adding a 1kΩ, 0.1µF filter solves this problem by providing
a charge reservoir that supplies the LTC2493 instantaneous
current, while the 1k resistor isolates the capacitive load
from the LT1494.
Conventional delta sigma ADCs input sampling current
lead to DC errors as a result of incomplete settling in the
external RC network.
The Easy Drive technology cancels the differential input
current. By balancing the negative input (CH3) with a 1kΩ,
0.1µF network errors due to the common mode input
current are cancelled.
2493fa
30
LTC2493
Package Description
DE Package
14-Lead Plastic DFN (4mm × 3mm)
(Reference LTC DWG # 05-08-1708 Rev B)
0.70 ±0.05
3.30 ±0.05
3.60 ±0.05
2.20 ±0.05
1.70 ± 0.05
PACKAGE
OUTLINE
0.25 ± 0.05
0.50 BSC
3.00 REF
RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS
APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED
4.00 ±0.10
(2 SIDES)
R = 0.05
TYP
3.00 ±0.10
(2 SIDES)
R = 0.115
TYP
8
0.40 ± 0.10
14
3.30 ±0.10
1.70 ± 0.10
PIN 1 NOTCH
R = 0.20 OR
0.35 × 45°
CHAMFER
PIN 1
TOP MARK
(SEE NOTE 6)
(DE14) DFN 0806 REV B
7
0.200 REF
1
0.25 ± 0.05
0.50 BSC
0.75 ±0.05
3.00 REF
0.00 – 0.05
BOTTOM VIEW—EXPOSED PAD
NOTE:
1. DRAWING PROPOSED TO BE MADE VARIATION OF VERSION (WGED-3) IN JEDEC
PACKAGE OUTLINE MO-229
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE
TOP AND BOTTOM OF PACKAGE
2493fa
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
31
LTC2493
Typical Application
5V
5V
R1
51.1k
C4
0.1µF
12
10µF
IIN+ = 0
R3
10k TO 100k
R4
IIN– = 0
51.1k
14
8
5V
9
10
5V
102k
11
+
0.1µF
10k TO 100k
7
1k
LT1494
–
= EXTERNAL OSCILLATOR
= INTERNAL OSCILLATOR
1
FO
LTC2493
13
0.1µF
C3
0.1µF
VCC
1.7k
REF +
REF–
5
SDA
4
SCL
2-WIRE
I2C INTERFACE
CH0
CH1
CA0
CH2
CA1
CH3
COM
GND
2
3
9-PIN SELECTABLE
ADDRESSES
6
2493 F37
0.1µF
1k
0.1µF
Figure 37. Easy Drive ADCs Simplify Measurement of High Impedance Sensors
Related Parts
PART NUMBER
DESCRIPTION
COMMENTS
LT1236A-5
Precision Bandgap Reference, 5V
0.05% Max Initial Accuracy, 5ppm/°C Drift
LT1460
Micropower Series Reference
0.075% Max Initial Accuracy, 10ppm/°C Max Drift
LT1790
Micropower SOT-23 Low Dropout Reference Family
0.05% Max Initial Accuracy, 10ppm/°C Max Drift
LTC2400
24-Bit, No Latency ΔΣ ADC in SO-8
0.3ppm Noise, 4ppm INL, 10ppm Total Unadjusted Error, 200µA
LTC2410
24-Bit, No Latency ΔΣ ADC with Differential Inputs
0.8µVRMS Noise, 2ppm INL
LTC2440
24-Bit, High Speed, Low Noise ΔΣ ADC
3.5kHz Output Rate, 200nV Noise, 24.6 ENOBs
LTC2442
24-Bit, High Speed, 2-/4-Channel ΔΣ ADC with Integrated
Amplifier
8kHz Output Rate, 200nV Noise, Simultaneous 50Hz/60Hz
Rejection
LTC2449
24-Bit, High Speed, 8-/16-Channel ΔΣ ADC
8kHz Output Rate, 200nV Noise, Simultaneous 50Hz/60Hz
Rejection
LTC2480/LTC2482/
LTC2484
16-Bit/24-Bit ΔΣ ADCs with Easy Drive Inputs, 600nV Noise,
Programmable Gain, and Temperature Sensor
Pin Compatible 16-Bit and 24-Bit Versions
LTC2481/LTC2483/
LTC2485
16-Bit/24-Bit ΔΣ ADCs with Easy Drive Inputs, 600nV Noise,
I2C Interface, Programmable Gain, and Temperature Sensor
Pin Compatible 16-Bit and 24-Bit Versions
LTC2486/LTC2488/
LTC2492
16-Bit/24-Bit 2-/4-Channel ΔΣ ADC with Easy Drive Inputs, SPI
Interface, Programmable Gain, and Temperature Sensor
Pin-Compatible 16-Bit and 24-Bit Versions
LTC2487
16-Bit 2-/4-Channel ΔΣ ADC with Easy Drive Inputs and
I2C Interface, Temperature Sensor
Pin-Compatible with LTC2493/LTC2489
LTC2489
16-Bit 2-/4-Channel ΔΣ ADC with Easy Drive Inputs
Pin-Compatible with LTC2487/LTC2493
LTC2495/LTC2497/
LTC2499
16-Bit/24-Bit 8-/16-Channel ΔΣ ADC with Easy Drive Inputs and
I2C Interface, Programmable Gain, and Temperature Sensor
Pin-Compatible 16-Bit and 24-Bit Versions
LTC2496/LTC2498
16-Bit 8-/16-Channel ΔΣ ADC with Easy Drive Inputs and
SPI Interface
Pin-Compatible with LTC2498/LTC2449
2493fa
32 Linear Technology Corporation
LT/CGRAFX 0407 REV A • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com
 LINEAR TECHNOLOGY CORPORATION 2007