M54HC4066 RAD-HARD QUAD BILATERAL SWITCH ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ HIGH SPEED: tPD = 7ns (TYP.) at VCC = 6V LOW POWER DISSIPATION: ICC = 1µA(MAX.) at TA=25°C LOW "ON" RESISTANCE: RON = 50Ω TYP. AT VCC = 9V, II/O = 100 µA WIDE OPERATING VOLTAGE RANGE VCC (OPR) = 2V TO 12V SINE WAVE DISTORTION: 0.042% at VCC = 4V f = 1KHz HIGH NOISE IMMUNITY: VNIH = VNIL = 28% VCC (MIN.) PIN AND FUNCTION COMPATIBLE WITH 54 SERIES 4066 SPACE GRADE-1: ESA SCC QUALIFIED 50 krad QUALIFIED, 100 krad AVAILABLE ON REQUEST NO SEL UNDER HIGH LET HEAVY IONS IRRADIATION DEVICE FULLY COMPLIANT WITH SCC-9408-052 DILC-14 FPC-14 ORDER CODES PACKAGE FM EM DILC FPC M54HC4066D M54HC4066K M54HC4066D1 M54HC4066K1 The C input is provided to control the switch; the switch is on when the C input is held high and off when C is held low. DESCRIPTION The M54HC4066 is an high speed CMOS QUAD BILATERAL SWITCH fabricated with silicon gate C2MOS technology. PIN CONNECTION May 2004 Rev. 1 1/11 M54HC4066 Figure 1: IEC Logic Symbols Figure 2: Logic Diagram Table 1: Pin Description PIN N° SYMBOL 1, 4, 8, 11 1 to 4 I/O 2, 3, 9, 10 1 to 4 O/I 13, 5, 6, 12 1C to 4C 7 14 GND VCC NAME AND FUNCTION Independent Inputs/Outputs Independent Outputs/ Inputs Enable Inputs (Active High) Ground (0V) Positive Supply Voltage Table 2: Truth Table CONTROL SWITCH FUNCTION H L ON OFF Table 3: Absolute Maximum Ratings Symbol Parameter VCC Supply Voltage VIN DC Input Voltage VI/O DC Input/Output Voltage IOK IIOK IO Value Unit -0.5 to +13 V -0.5 to VCC + 0.5 -0.5 to VCC + 0.5 V Control Input DC Diode Current ± 20 mA I/O DC Diode Current ± 20 mA DC Output Source Sink Current Per Output Pin ± 25 mA ± 50 mA ICC or IGND DC VCC or Ground Current PD Power Dissipation Tstg Storage Temperature TL Lead Temperature (10 sec) V 300 mW -65 to +150 °C 265 °C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied 2/11 M54HC4066 Table 4: Recommended Operating Conditions Symbol Parameter VCC Supply Voltage Value Unit 2 to 12 V VIN Input Voltage (Control) 0 to VCC V VI/O I/O Voltage 0 to VCC V Top Operating Temperature -55 to 125 °C Input Rise and Fall Time tr, tf VCC = 2.0V 0 to 1000 VCC = 4.5V 0 to 500 VCC = 6.0V 0 to 400 VCC = 10.0V 0 to 250 ns Table 5: DC Specifications Test Condition Symbol VIHC VILC RON ∆RON IOFF IIZ IIN ICC Parameter High Level Control Input Voltage Low Level Control Input Voltage ON Resistance Difference of ON Resistance between switches Input/Output Leakage Current (SWITCH OFF) Switch Input Leakage Current (SWITCH ON, OUTPUT OPEN) Control Input Current Quiescent Supply Current TA = 25°C VCC (V) Min. 2.0 4.5 9.0 12.0 2.0 4.5 9.0 12.0 4.5 VI = VIHC V = 9.0 I/O V CC to GND II/O ≤ 1mA 12.0 4.5 VI = VIHC 9.0 VI/O = VCC or GND II/O ≤ 1mA 12.0 4.5 VI = VIHC 9.0 VI/O = VCC or GND II/O ≤ 1mA 12.0 VOS = VCC or GND 12.0 VIS = VCC or GND VIN = VILC 12.0 6.0 6.0 9.0 12.0 Value Typ. Max. 1.5 3.15 6.3 8.4 -40 to 85°C -55 to 125°C Min. Min. Max. 1.5 3.15 6.3 8.4 96 55 45 70 50 45 10 5 5 0.5 1.35 2.7 3.6 170 85 80 100 75 70 Max. 1.5 3.15 6.3 8.4 0.5 1.35 2.7 3.6 200 100 90 130 95 90 Unit V 0.5 1.35 2.7 3.6 250 150 120 160 115 110 V Ω Ω ± 0.1 ±1 ±2 µA VOS = VCC or GND VIN = VIHC ± 0.1 ±1 ±2 µA VI = VCC or GND ± 0.1 ±1 ±1 µA VI = VCC or GND 1 4 8 10 40 80 20 80 160 µA 3/11 M54HC4066 Table 6: AC Electrical Characteristics (CL = 50 pF, Input tr = tf = 6ns) Test Condition Symbol ΦI/O tPZL tPZH tPLZ tPHZ Parameter TA = 25°C VCC (V) 2.0 4.5 9.0 12.0 Output Enable Time 2.0 4.5 9.0 12.0 Output Disable 2.0 Time 4.5 9.0 12.0 Maximum Control 2.0 Input Frequency 4.5 9.0 12.0 Value Min. Phase Difference Between Input and Output RL = 1KΩ RL = 1KΩ RL = 1KΩ CL = 15 pF VOUT = 1/2 VCC Typ. Max. 10 4 3 3 18 8 6 6 20 10 8 8 30 30 30 30 50 10 8 7 100 20 12 12 115 23 20 18 -40 to 85°C -55 to 125°C Min. Min. Max. 65 13 10 9 125 25 22 18 145 29 25 22 Unit Max. 75 15 13 10 150 30 27 25 175 35 30 27 ns ns ns MHz Table 7: Capacitive Characteristics Test Condition Symbol Parameter VCC (V) Value TA = 25°C Min. Typ. Max. 10 -40 to 85°C -55 to 125°C Min. Min. Max. Unit Max. CIN Input Capacitance 5 CI/O Switch Terminal Capacitance Feed Through Capacitance Power Dissipation Capacitance (note 1) 6 pF 0.5 pF 15 pF CIOS CPD 10 10 pF 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC 4/11 M54HC4066 Table 8: Analog Switch Characteristics (GND = 0V;TA = 25°C) Symbol Parameter Sine Wave Distortion (THD) fMAX Frequency Response (Switch ON) Feed through Attenuation (Switch OFF) Crosstalk (Control Input to Signal Output) Crosstalk (Between Any Switches) Test Condition VCC (V) VIN (Vp-p) 4.5 9.0 4.5 9.0 4 8 Value Unit Typ. fIN = 1 KHz RL = 10 KΩ, CL = 50 pF Adjust fIN voltage to obtain 0 dBm at VOS. Increase fIN Frequency until dB meter reads -3dB RL = 50Ω, CL = 10 pF 0.05 0.04 200 200 MHz % 4.5 9.0 VIN is centered at VCC/2. Adjust input for 0 dBm RL = 600Ω CL = 50 pF, fIN = 1MHz sine wave -60 -60 dB 4.5 9.0 RL = 600Ω, CL = 50 pF, fIN = 1MHz square wave (tr = tf =6ns) 60 100 mV 4.5 9.0 Adjust VIN to Obtain 0 dBmat input RL = 600Ω, CL = 50 pF, fIN = 1MHz sine wave -60 -60 dB 5/11 M54HC4066 Figure 3: Switching Characteristics Test Circuit CROSSTALK (control to output) CROSSTALK BETWEEN ANY TWO SWITCHES BANDWIDTH AND FEEDTHROUGH ATTENUATION MAXIMUM CONTROL FREQUENCY 6/11 M54HC4066 Figure 4: Channel Resistance (RON) Figure 5: ICC (Opr.) 7/11 M54HC4066 DILC-14 MECHANICAL DATA mm. inch DIM. MIN. TYP MAX. MIN. TYP. MAX. A 2.1 2.54 0.083 0.100 a1 3.00 3.70 0.118 0.146 a2 0.63 0.88 1.14 0.025 0.035 0.045 B 1.82 2.03 2.39 0.072 0.080 0.094 b 0.40 0.45 0.50 0.016 0.018 0.020 b1 0.20 0.254 0.30 0.008 0.010 0.012 D 18.79 19.00 19.20 0.740 0.748 0.756 E 7.36 7.62 7.87 0.290 0.300 0.310 e 2.54 0.100 e1 15.11 15.24 15.37 0.595 0.600 0.605 e2 7.62 7.87 8.12 0.300 0.310 0.320 F 7.11 7.75 0.280 I 0.305 3.70 K 10.90 L 1.14 1.27 0.146 12.1 0.429 1.5 0.045 0.476 0.050 0.059 0016173H 8/11 M54HC4066 FPC-14 MECHANICAL DATA mm. inch DIM. MIN. TYP MAX. MIN. TYP. MAX. A 6.75 6.91 7.06 0.266 0.272 0.278 B 9.76 9.95 10.14 0.384 0.392 0.399 C 1.49 1.95 0.059 D 0.10 0.127 0.15 0.004 0.005 0.006 E 7.50 7.62 7.75 0.295 0.300 0.305 F G 1.27 0.38 0.050 0.43 H L 0.077 0.48 0.015 0.017 6.0 0.019 0.236 18.75 22.0 0.738 0.866 M 0.38 0.015 N 4.31 0.170 G F D H 14 8 L N A 7 1 H E B M C 016029E 9/11 M54HC4066 Table 9: Revision History Date Revision 14-May-2004 1 10/11 Description of Changes First Release M54HC4066 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics All other names are the property of their respective owners © 2004 STMicroelectronics - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States. http://www.st.com 11/11