MAS MAS6240A1TC00

DA6240.001
20 November 2006
MAS6240
Piezo Driver with Multi-Mode Charge Pump
This is preliminary information on a new
product under development. Micro Analog
Systems Oy reserves the right to make any
changes without notice.
• Both Single Ended and
Differential Output
• Three-Step Volume Adjusting
• Up to 18Vpp Output from 3V
Supply
• One Wire Audio & Shutdown
Control
• High Efficiency
• Solution without Inductors
• Low External Part Count
DESCRIPTION
MAS6240 is a piezo driver device that can drive
outputs up to 18Vpp from 3V supply. An internal
three-mode charge pump generates boosted supply
voltage for piezo driver. For adjusting the piezo
element sound volume, the charge pump can
operate in either of a 1x, 2x or 3x mode. In 1x mode
the input voltage is bypassed to the output, in 2x or
3x mode the input voltage is boosted up accordingly
2 or 3 times. Charge pump mode is selected by
control pins EN1 and EN2 (see Table1 at page 2).
MAS6240 is an easy and low-cost solution for piezo
driver, since only 4 small value capacitors are
needed in addition to sound element - the use of
inductors can be avoided. The inductorless design
also causes significantly less disturbance to the
surrounding circuits making it an ideal choice for
sensitive designs. Its charge pump switches at
1MHz, allowing to use as small as 100nF external
capacitors.
Control logic is switching the charge pump on at
first rising signal of digital input (DIN) pin. The
switch-off signal will be generated while the signal at
DIN has been low at least for 10ms. The piezo
driver is enabled at a second rising edge of a pulse
at DIN and the signal is transferred to piezo output
VO1. The same signal is inverted into output VO2
for using differential output.
Continuous logic high level at DIN input causes the
charge pump to be turned ON but leaves the audio
amplifier disabled. In that state the charge pump
output can be used to power the external LEDs or
any other external circuit. The output voltage is still
selectable at three steps.
In "disabled" mode (DIN has been low for 10ms) all
functional blocks are switched off to achieve the
quiescent current less than 1µA.
See more information in the chapter Detailed
Description.
FEATURES
APPLICATIONS
Thin 0.75 mm QFN 12 package
Piezo Driver
• Three-Step Volume Adjusting
• Both Single Ended and Differential Output
• Up to 18Vpp Output from 3V Supply
• One Wire Audio & Shutdown Control
•Wrist Watches
•Alarm Clocks
•Handheld GPS devices
•PDAs
•Portable Device with Sound Feature
Charge Pump
• Low External Part Count
• Solution without Inductors
• 1 MHz Switching Frequency
• Multi-Mode Charge Pump (1x/2x/3x)
1 (10)
DA6240.001
20 November 2006
BLOCK & APPLICATION DIAGRAM
0.1uF
CP1
0.1uF
CN1
CP2
CN2
VIN (3V)
1x/2x/3x Charge Pump
Oscillator
1MHz
0.1uF
EN1
EN2
VOUT
0.1uF
Short Circuit
Protection
Control
Logic
DIN
VO1
PIEZO SOUNDER
VO2
GND
Figure 1: Charge Pump + Single End Piezo Driver (max 9Vpp)
0.1uF
CP1
0.1uF
CN1
CP2
CN2
VIN (3V)
Oscillator
1MHz
0.1uF
EN1
EN2
1x/2x/3x Charge Pump
Control
Logic
VOUT
0.1uF
Short Circuit
Protection
DIN
VO1
PIEZO SOUNDER
VO2
GND
Figure 2: Charge Pump + Differential Piezo Driver (max 18Vpp)
Table 1 Charge Pump boosting mode selection
DIN
EN1
EN2
Charge Pump
0
1
1
1
1
0
0
1
1
0
1
0
1
OFF
OFF
1x Mode (VIN)
2x Mode (2xVIN)
3x Mode (3xVIN)
Note: Pulsed signal at digital input DIN is taken as “1” if pulse low time is less than 10 ms!
2 (10)
DA6240.001
20 November 2006
PIN DESCRIPTION
Pin Description
Symbol
Type
Control signal input for setting charge pump mode
Control signal input for setting charge pump mode
Enable signal + Digital signal input
Flying capacitor negative terminal
Supply ground
Digital audio signal output
Digital audio signal output
Flying capacitor negative terminal
Flying capacitor positive terminal
Charge pump output
Flying capacitor positive terminal
Power supply
EN1
EN2
DIN
CN1
GND
VO2
VO1
CN2
CP1
VOUT
CP2
VIN
DI
DI
DI
I/O
G
DO
DO
I/O
I/O
AO
I/O
P
X-coordinate
Y-coordinate
152 µm
152 µm
152 µm
672 µm
808 µm
980 µm
980 µm
980 µm
980 µm
765 µm
612 µm
447 µm
989 µm
804 µm
588 µm
200 µm
202 µm
225 µm
378 µm
558 µm
711 µm
1000 µm
1000 µm
999 µm
G = Ground, P = Power, D = Digital, A = Analog, I = Input, O = Output.
Note: Because the substrate of the die is internally connected to GND, the die has to be connected to GND or
left floating. Please make sure that GND is the first pad to be bonded. Pick-and-place and all component
assembly are recommended to be performed in ESD protected area.
Note: Pad coordinates are measured from the left bottom corner of the chip to the center of the pads. The
coordinates may vary depending on sawing width and location, however, distances between pads are accurate.
Note: See IC outlines on a page 6 for IC layout.
ABSOLUTE MAXIMUM RATINGS
Parameter
Symbol
Supply Voltage
Outputs and Flying
Capacitors Pins Voltages
VIN
VOUT,
CP1, CP2,
CN1, CN2,
VO1, VO2
DIN,
EN1, EN2
tSC
Voltage Range for Input
Pins
VOUT Short-Circuit
Duration
Storage Temperature
ESD Rating
Conditions
Min
Max
Unit
-0.3
-0.3
5.5
10
V
V
-0.3
VIN + 0.3
V
Note 1
Indefinite
-55
o
+150
1
Human Body Model (HBM)
C
kV
NOTE 1. SHORT CIRCUIT CURRENT INTERNALLY LIMITED.
RECOMMENDED OPERATING CONDITIONS
All voltages with respect to ground.
Parameter
Operating Junction
Temperature
Operating Ambient
Temperature
Operating Supply Voltage
Symbol
Conditions
Min
Typ
Max
Unit
+125
°C
TJ
-40
TA
-40
+27
+85
°C
VIN
2.5
3.0
3.3
V
3 (10)
DA6240.001
20 November 2006
ELECTRICAL CHARACTERISTICS
TA = -40°C to +85°C, typical values at TA = 27°C, VIN = 3.0 V, C1 = 100 nF, C2 = 100 nF, COUT = 100 nF, CIN = 100 nF, Cpiezo = 15 nF, digital
input DIN=4kHz; unless otherwise specified
Parameter
Output Voltage
Current Consumption
Signal Frequency
Symbol
VOUT
ICC
ISD
Internal Switching
Frequency (Charge Pump)
VOUT Turn-ON Time
(From DIN signal HIGH to
90% VOUT steady state)
Shut Down delay
FOSC
Short Circuit Current Limit
ISC
Control Input Threshold
VIH
VIL
IIH
IIL
tON
tOFF
IIH
IIL
IIH
IIL
Min
VOUT pin voltage towards ground
at VDD = 3 V
1x Mode (no load)
2x Mode (no load)
3x Mode (no load)
Charge Pump (no load):
1x Mode
2x Mode
3x Mode
Single ended application
(Cpiezo = 15nF; f=4kHz):
1x Mode
2x Mode
3x Mode
Differential application
(Cpiezo = 15 nF; f=4kHz):
1x Mode
2x Mode
3x Mode
FAUDIO
Shutdown Current
Control Input Current
Conditions
Typ
EN1, EN2, DIN pins
VDIN = 3V, (900kΩ pull down)
VDIN = 0V
VDIN = 3V
VEN1,EN2 = 3V, (900kΩ pull down)
VEN1,EN2 = 0V
VDIN = 0V
VEN1,EN2 = 3V
VEN1,EN2 = 0V
Unit
3
6
9
V
50
490
820
µA
0.27
1.3
2.7
mA
mA
0.2
0.88
3.5
7.6
4
8
1
µA
0.6
1
1.8
MHz
10
10
60
120
20
ms
10
30
mA
DIN = 0V,
1x Mode
2x Mode
3x Mode
Time before device shutdown after
DIN signal goes to LOW
From VIN pin
Max
kHz
µs
1.6
3.4
0
0.55
7
1
V
V
µA
µA
3.4
0
7
1
µA
µA
0
0
1
1
µA
µA
4 (10)
DA6240.001
20 November 2006
DETAILED DESCRIPTION
MAS6240 first pulse skipping
10
9
8
7
voltage [V]
6
5
VO1
4
DIN
3
2
1
0
-1
-20
-10
0
10
20
30
40
50
60
70
time [ms]
Figure 3: Enabling output VO1
The piezo driver is enabled at the second rising edge of the pulse at DIN, thus the signal is transferred to the
piezo output VO1. An output VO2 is enabled at the same time, but it is optional to take it in use. Control logic is
switching the charge pump on at first rising signal of digital input DIN pin. If only one continous pulse is fed to the
input DIN, the output VO1 is not enabled. This make it possible to control e.g. a white LED or other device
through pin VOUT while charge pump is enabled, without enabling the piezo output VO1.
MAS6240 first pulse skipping & power down delay
10
8
voltage [V]
6
DIN
4
VO2
2
0
-20
-10
0
10
20
30
40
50
60
70
-2
time [sec]
Figure 4: Disabling VO2
Figure 4 is drawn in the case of VO2. The switch-off signal will be generated after the signal at DIN has been low
at least for 10 ms. In the figure 4 the switch-off delay is about 25 ms. Again when new pulses are fed into DIN,
the charge pump and piezo driver will be enabled.
5 (10)
DA6240.001
20 November 2006
VOUT
VIN
CP2
IC OUTLINES
EN2
CP1
DIN
CN2
1200 µm
EN1
VO1
MAS6240
GND
CN1
VO2
1130 µm
DIE size = 1.13 x 1.20 mm; PAD size = 80 x 80 µm
DEVICE OUTLINE CONFIGURATION
QFN 3x3 12ld
7
10
1234
GAv 4
YWW
1
Top Marking Information:
1234 = Product Number
Av = Version Number
G = Lead Free, RoHS Compliant Package
YWW = Year Week
Pin nr.
1
2
3
Pin Name
EN1
EN2
DIN
Pin nr.
4
5
6
Pin Name
CN1
GND
VO2
Pin nr.
Pin Name
Pin nr.
Pin Name
7
8
9
VO1
CN2
CP1
10
11
12
VOUT
CP2
VIN
6 (10)
DA6240.001
20 November 2006
PACKAGE (QFN 3X3x0.75 12ld) OUTLINE
D
D/2
E/2
TOP VIEW
A3
A
PIN 1 MARK AREA
SIDE VIEW
A1
SEATING
PLANE
DETAIL A
D2
b
D2/2
L
Terminal Tip
e
Package Center Line X or Y
E2
E2/2
SHAPE OF PIN #1
IDENTIFICATION
IS OPTIONAL
BOTTOM VIEW
EXPOSED PAD
DETAIL A
Symbol
Min
Nom
Max
PACKAGE DIMENSIONS
A
0.700
0.750
0.800
A1
0.000
0.020
0.050
A3
0.178
--0.228
b
0.180
--0.300
D
2.950
3.000
3.050
D2 (Exposed.pad)
1.300
--1.550
E
2.950
3.000
3.050
E2 (Exposed.pad)
1.300
--1.550
e
0.500 BSC
L
0.300
--0.500
Dimensions do not include mold or interlead flash, protrusions or gate burrs.
Unit
mm
mm
mm
mm
mm
mm
mm
mm
mm
mm
2500 Components on Each Reel
Reel Material: Conductive, Plastic Antistatic or Static Dissipative
Carrier Tape Material: Conductive
Cover Tape Material: Static Dissipative
7 (10)
DA6240.001
20 November 2006
SOLDERING INFORMATION
◆ For Lead-Free / Green QFN 3mm x 3mm x 0.75mm
Resistance to Soldering Heat
Maximum Temperature
Maximum Number of Reflow Cycles
Reflow profile
According to RSH test IEC 68-2-58/20
260°C
3
Thermal profile parameters stated in IPC/JEDEC J-STD-020
should not be exceeded. http://www.jedec.org
7.62 - 25.4 µm, Matte Tin
Lead Finish
EMBOSSED TAPE SPECIFICATIONS
P2
PO
P1
D0
T
X
E
W
F
B0
R 0.25 typ
K0
X
A0
User Direction of Feed
Dimension
Ao
Bo
Do
E
F
Ko
Po
P1
P2
T
W
Min/Max
3.30 ±0.10
3.30 ±0.10
1.50 +0.1/-0.0
1.75
5.50 ±0.05
1.10 ±0.10
4.0
8.0
±0.10
2.0
±0.05
0.3
±0.05
12.00 ±0.3
All dimensions in millimeters
Unit
Mm
Mm
Mm
Mm
Mm
Mm
Mm
Mm
Mm
Mm
Mm
8 (10)
DA6240.001
20 November 2006
REEL SPECIFICATIONS
W2
A
D
C
Tape Slot for Tape Start
N
B
W1
Carrier Tape
Cover Tape
End
Start
Trailer
Dimension
A
B
C
D
N
W 1 (measured at hub)
W 2 (measured at hub)
Trailer
Leader
Components
Min
1.5
12.80
20.2
100
12.4
160
390,
of which minimum 160 mm of
empty carrier tape sealed with
cover tape
Leader
Max
Unit
330
mm
mm
mm
mm
mm
mm
mm
mm
mm
13.50
14.4
18.4
9 (10)
DA6240.001
20 November 2006
ORDERING INFORMATION
Product Code
Product
Package
Comments
MAS6240A1HP06
Piezo Driver with Multi-Mode
Charge Pump
Piezo Driver with Multi-Mode
Charge Pump
QFN 3x3x0.75 12ld, Pb Free,
RoHS Compliant
EWS Tested wafers 400 µm
Tape and Reel
MAS6240A1TC00
Die size 1.13 x 1.20
mm
The formation of product code
An example for MAS6240A1HP06:
MAS6240
Product name
A
Design version
1
Product
Version
HP
Package:
HP = QFN 3 x 3 x 0.75
(Pb free, RoHS compliant)
06
Delivery format:
06 = T&R
08 = Loose components
LOCAL DISTRIBUTOR
MICRO ANALOG SYSTEMS OY CONTACTS
Micro Analog Systems Oy
Kamreerintie 2, P.O.Box 51
FIN-02771 Espoo, FINLAND
Tel. +358 9 80 521
Telefax +358 9 805 3213
http://www.mas-oy.com
NOTICE
Micro Analog Systems Oy reserves the right to make changes to the products contained in this data sheet in order to improve the design or
performance and to supply the best possible products. Micro Analog Systems Oy assumes no responsibility for the use of any circuits
shown in this data sheet, conveys no license under any patent or other rights unless otherwise specified in this data sheet, and makes no
claim that the circuits are free from patent infringement. Applications for any devices shown in this data sheet are for illustration only and
Micro Analog Systems Oy makes no claim or warranty that such applications will be suitable for the use specified without further testing or
modification.
10 (10)