MN102L610B Type MN102L610B ROM (×× 8-bit / × 16-bit) External RAM (×× 8-bit / × 16-bit) 4K Package LQFP100-P-1414 *Lead-free Minimum Instruction Execution Time 88.5 ns (at 4.5 V to 5.5 V, 22.6 MHz) Interrupts • RESET • Watchdog • Timer counter 0 to 5 • Timer counter 6 to 7 • Timer counter 6 to 7 compare capture A • Timer counter 6 to 7 compare capture B • ATC transfer finish • External 0 to 4 • Serial ch.0, 1 transmission • Serial ch.0, 1 reception • NMI pin • A/D conversion finish Timer Counter Timer counter 0 : 8-bit × 1 (timer output, event count) Clock source ····················· 1/1, 1/128 of system clock frequency; 1/4 of low speed clock frequency; external clock Interrupt source ················ underflow of timer counter 0 Timer counter 1 : 8-bit × 1 (timer output, event count, A/D conversion start up) Clock source ····················· system clock; 1/4 of low speed clock frequency; external clock; timer counter 0 output Interrupt source ················ underflow of timer counter 1 Timer counter 2 to 3 : 8-bit × 1 (timer output, event count, UART baud rate generator) Clock source ····················· system clock; external clock; timer counter 0 output; timer counter 1, 2 output Interrupt source ················ underflow of timer counter 2, 3 Timer counter 4, 5 : 8-bit × 1 (timer output, event count) Clock source ····················· 1/4 of low speed clock frequency; external clock; timer counter 0 output; timer counter 3, 4 output Interrupt source ················ underflow of timer counter 4, 5 Timer counter 6, 7 : 16-bit × 1 (timer output, event count, input capture, output compare, PWM output, 2-phase encoder input) Clock source ····················· system clock; external clock; timer counter 4, 5 output Interrupt source ················ coincidence with compare capture A or at capture; coincidence with compare capture B or at capture; underflow of timer counter 6, 7 Connectable timer counter 0 to 5 Serial 0 : 7, 8-bit × 1 (common use with UART, transfer direction of MSB/LSB selectable) Clock source ····················· 1/16 of timer counter 2 frequency; 1/16 of timer counter 3 frequency; external clock; 1/2 of timer counter 2 frequency Serial Interface Serial 1 : 7, 8-bit × 1 (common use with UART, transfer direction of MSB/LSB selectable) Clock source ····················· 1/16 of timer counter 2 frequency; 1/16 of timer counter 3 frequency; external clock; 1/2 of timer counter 3 frequency UART × 2 (common use with serial 0, 1) I2C × 2 (single master) I/O Pins 1 I/O 80 48 • Common use : 16 (by 8 bits), 8 (by 4 bits), 56 (by bit)(MN102LF61G) • Common use : 8 (by 4 bits), 40 (by bit)(MN102L610B) A/D Inputs 8-bit × 8-ch. (with S/H) PWM 16-bit × 2-ch. Special Ports LED drive port × 2 Notes Burst ROM inferface support, ATC (between serial 0ch and internal RAM) support MAE00004CEM MN102L610B Electrical Characteristics A/D characteristics Limit Parameter Symbol Condition Unit min A/D conversion relative error max ch.0 to 3 ±3 ch.4 to 7 ±4 VDD = 5 V , VSS = 0 V A/D conversion time Analog input voltage typ µs 4.248 VIA VSS LSB VDD V (Ta = 25°C , VDD = 5.0 V , VSS = 0 V) SBI1,P74 SBT1,P73 SBO0,P72 SBI0,P71 SBT0,P70 VDD AN3,P97 AN2,P96 AN1,P95 AN0,P94 (LED drive) VSS TM7IC,P93 (LED drive) TM7IOB,P92 TM7IOA,P91 TM6IC,P90 TM6IOB,P87 TM6IOA,P86 VDD TM5IO,P85 TM4IO,P84 TM3IO,P83 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 38 39 40 41 42 43 44 45 46 47 48 49 50 SBO1,P75 72 73 74 37 36 35 34 33 32 31 30 29 28 27 22 23 24 25 XO VDD OSCI OSCO MODE 26 21 20 XI 17 VDD 19 16 P23,A03 VSS 15 P22,A02 18 14 P21,A01 SYSCLK 13 P20,A00 *P17,D15,AD15 12 P16,D14,AD14 *P57, WORD *P15,D13,AD13 11 *P14,D12,AD12 *P56,ALE, ALE, BSTRE *P13,D11,AD11 10 *P12,D10,AD10 P55, BRACK *P11,D09,AD09 9 *P10,D08,AD08 P54, BREQ VSS 8 P07,D07,AD07 *P53, CS3 P06,D06,AD06 MN102L610B 7 P05,D05,AD05 *P52, CS2 P04,D04,AD04 6 P03,D03,AD03 5 P02,D02,AD02 4 P01,D01,AD01 *P51, CS1 P00,D00,AD00 *P50, CS0 VDD *P63, WEH RST 3 *PA5,ADSEP *P62, WEL PA4, IRQ4 2 PA3, IRQ3 1 PA2, IRQ2 *P61,RE PA1, IRQ1 P60,WAIT PA0, IRQ0 100 98 96 94 92 90 88 86 84 82 80 78 76 99 97 95 93 91 89 87 85 83 81 79 77 75 NMI Pin Assignment TM2IO,P82 TM1IO,P81 TM0IO,P80 A23,WDOUT,AN7,P47 A22,STOP,AN6,P46 A21,AN5,P45* A20,AN4,P44* VSS A19,P43* A18,P42* A17,P41* A16,P40* A15,P37 A14,P36 A13,P35 A12,P34 VDD A11,P33 A10,P32 A09,P31 A08,P30 A07,P27 A06,P26 A05,P25 A04,P24 LQFP100-P-1414 *Lead-free * Port unusable in MN102L610B * The MN102LF61G is manufactured and sold under license agreement with BULL CP8 Inc. Note that MN102LF61G cannot be used as the IC card. Support Tool In-circuit Emulator PX-ICE102L00 + PX-PRB102L53-LQFP100-P-1414 Flash Memory Built-in Type Type MN102LF61G ROM (× 8-bit / × 16-bit) 128 K RAM (× 8-bit / × 16-bit) 4K Minimum instruction execution time 88.5 ns (at 4.5 V to 5.5 V, 22.6 MHz) Package LQFP100-P-1414 *Lead-free MAE00004CEM 2 Request for your special attention and precautions in using the technical information and semiconductors described in this material (1) An export permit needs to be obtained from the competent authorities of the Japanese Government if any of the products or technologies described in this material and controlled under the "Foreign Exchange and Foreign Trade Law" is to be exported or taken out of Japan. (2) The technical information described in this material is limited to showing representative characteristics and applied circuits examples of the products. It neither warrants non-infringement of intellectual property right or any other rights owned by our company or a third party, nor grants any license. (3) We are not liable for the infringement of rights owned by a third party arising out of the use of the product or technologies as described in this material. (4) The products described in this material are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances). Consult our sales staff in advance for information on the following applications: • Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. • Any applications other than the standard applications intended. (5) The products and product specifications described in this material are subject to change without notice for modification and/or improvement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to make sure that the latest specifications satisfy your requirements. (6) When designing your equipment, comply with the guaranteed values, in particular those of maximum rating, the range of operating power supply voltage, and heat radiation characteristics. Otherwise, we will not be liable for any defect which may arise later in your equipment. Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (7) When using products for which damp-proof packing is required, observe the conditions (including shelf life and amount of time let standing of unsealed items) agreed upon when specification sheets are individually exchanged. (8) This material may be not reprinted or reproduced whether wholly or partially, without the prior written permission of Matsushita Electric Industrial Co., Ltd. 2002 JUL