Pressure Freescale Semiconductor MPXH6400A Rev 4, 11/2009 High Temperature Accuracy Integrated Silicon Pressure Sensor for Measuring Absolute Pressure, On-Chip Signal Conditioned, Temperature Compensated and Calibrated MPXA6400A MPXH6400A MPXHZ6400A Series 20 to 400 kPa (3.0 to 58 psi) 0.2 to 4.8 V Output The Freescale MPXxx6400A series sensor integrates on-chip, bipolar op amp circuitry and thin film resistor networks to provide a high output signal and temperature compensation. The small form factor and high reliability of on-chip integration make the Freescale pressure sensor a logical and economical choice for the system designer. The MPXxx6400A series piezoresistive transducer is a state-of-the-art, monolithic, signal conditioned, silicon pressure sensor. This sensor combines advanced micromachining techniques, thin film metallization, and bipolar semiconductor processing to provide an accurate, high level analog output signal that is proportional to applied pressure. Application Examples • Industrial Controls • Engine Control/Manifold Absolute Pressure (MAP)/Liquefied Petroleum Gas (LPG) Features • • • • • • Improved Accuracy at High Temperature Available in Small and Super Small Outline Packages 1.5% Maximum Error over 0° to 85°C Ideally suited for Microprocessor or Microcontroller-Based Systems Temperature Compensated from -40° to +125°C Durable Thermoplastic (PPS) Surface Mount Package ORDERING INFORMATION Device Name Package Options Case No. None # of Ports Single Dual Gauge Pressure Type Differential Absolute Device Marking Small Outline Package (MPXA6400A Series) MPXA6400AP Tray 1369 • • MPXA6400A Super Small Outline Package (MPXH6400A Series) MPXH6400AC6U Rails 1317A • • MPXH6400A MPXH6400AC6T1 Tape and Reel 1317A • • MPXH6400A • MPXHZ6400A Super Small Outline Package (Media Resistant Gel) (MPXHZ6400A Series) MPXHZ6400AC6T1 Tape and Reel 1317A • SUPER SMALL OUTLINE PACKAGE SMALL OUTLINE PACKAGE MPXH6400AC6U/C6T1 MPXHZ6400AC6T1 CASE 1317A-04 MPXA6400AP CASE 1369-01 © Freescale Semiconductor, Inc., 2007-2009. All rights reserved. Pressure OPERATING CHARACTERISTICS (VS = 10 Vdc, TA = 25°C unless otherwise noted, P1 > P2) Characteristic Symbol Min Typ Max Unit Pressure Range POP 20 — 400 kPa Supply Voltage(1) VS 4.64 5.0 5.36 Vdc Supply Current Io — 6.0 10 mAdc Minimum Pressure Offset @ VS = 5.0 Volts(2) (0 to 85°C) Voff 0.133 0.2 0.267 Vdc Full Scale Output @ VS = 5.0 Volts(3) (0 to 85°C) VFSO 4.733 4.8 4.866 Vdc Full Scale Span @ VS = 5.0 Volts(4) (0 to 85°C) VFSS 4.467 4.6 4.733 Vdc Accuracy(5) (0 to 85°C) — — — ±1.5 %VFSS Sensitivity V/P — 12.1 — mV/kPa (6) tR — 1.0 — ms Time(7) — — 20 — ms — — ±0.25 — %VFSS Response Time Warm-Up Offset Stability(8) 1. Device is ratiometric within this specified excitation range. 2. Offset (Voff) is defined as the output voltage at the minimum rated pressure. 3. Full Scale Output (VFSO) is defined as the output voltage at the maximum or full rated pressure. 4. Full Scale Span (VFSS) is defined as the algebraic difference between the output voltage at full rated pressure and the output voltage at the minimum rated pressure. 5. Accuracy is the deviation in actual output from nominal output over the entire pressure range and temperature range as a percent of span at 25°C due to all sources of error including the following: Linearity:Output deviation from a straight line relationship with pressure over the specified pressure range. Temperature Hysteresis: Output deviation at any temperature within the operating temperature range, after the temperature is cycled to and from the minimum or maximum operating temperature points, with zero differential pressure applied. Pressure Hysteresis: Output deviation at any pressure within the specified range, when this pressure is cycled to and from the minimum or maximum rated pressure, at 25°C. TcSpan: Output deviation over the temperature range of 0 to 85°C, relative to 25°C. TcOffset: Output deviation with minimum rated pressure applied, over the temperature range of 0 to 85°C, relative to 25°C. Variation from Nominal: The variation from nominal values, for Offset or Full Scale Span, as a percent of VFSS, at 25°C. 6. Response Time is defined as the time for the incremental change in the output to go from 10% to 90% of its final value when subjected to a specified step change in pressure. 7. Warm-up Time is defined as the time required for the product to meet the specified output voltage after the Pressure has been stabilized. 8. Offset Stability is the product's output deviation when subjected to 1000 hours of Pulsed Pressure, Temperature Cycling with Bias Test. MPXH6400A 2 Sensors Freescale Semiconductor Pressure MAXIMUM RATINGS(1) Rating Symbol Value Unit Maximum Pressure (P1 > P2) PMAX 1600 kPa Storage Temperature TSTG -40° to +125° °C Operating Temperature TA -40° to +125° °C Output Source Current @ Full Scale Output(2) Io + 0.5 mAdc Output Sink Current @ Minimum Pressure Offset(2) Io - -0.5 mAdc 1. Exposure beyond the specified limits may cause permanent damage or degradation to the device. 2. Maximum Output Current is controlled by effective impedance from Vout to GND or Vout to VS in the application circuit. Figure 1 shows a block diagram of the internal circuitry integrated on a pressure sensor chip. 2 VS Thin Film Temperature Compensation and Gain Stage #1 Sensing Element 3 GND Gain Stage #2 and Ground Reference Shift Circuitry 4 Vout Pins 1, 5, 6, 7, and 8 are NO CONNECTS for small outline package and super small outline package devices. Figure 1. Fully Integrated Pressure Sensor Schematic MPXH6400A Sensors Freescale Semiconductor 3 Pressure Figure 1 illustrates the absolute sensing chip in the basic Super Small Outline chip carrier (Case 1317). Figure 2. illustrates a typical application circuit (output source current operation). Figure 3. shows the sensor output signal relative to pressure input. Typical minimum and maximum output curves are shown for operation over 0 to 85°C temperature range. The output will saturate outside of the rated pressure range. A fluorosilicone gel isolates the die surface and wire bonds from the environment, while allowing the pressure signal to be transmitted to the silicon diaphragm. The MPXxx6400A series pressure sensor operating characteristics, internal reliability and qualification tests are based on use of dry air as the pressure media. Media other than dry air may have adverse effects on sensor performance and long-term reliability. Contact the factory for information regarding media compatibility in your application. Fluoro Silicone Gel Die Coat Stainless Steel Cap Die P1 Wire Bond Thermoplastic Case Lead Frame Absolute Element Die Bond Sealed Vacuum Reference Figure 1. Cross Sectional Diagram SSOP (not to scale) +5.0 V VS Pin 2 MPXxx6400A VOUT Pin 4 100 nF To ADC 47 pF GND Pin 3 51 K Figure 2. Typical Application Circuit (Output Source Current Operation) 5.0 4.5 4.0 Output (Volts) 3.5 Transfer Function: VOUT = VS x (0.002421xP–0.00842 ± Error VS = 5.0 VDC Temperature = 0 to 85°C 3.0 2.5 MAX 2.0 TYP 1.5 1.0 0 MIN 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 320 340 360 380 400 0.5 Pressure (Reference to Sealed Vacuum) in kPa Figure 3. Output vs. Absolute Pressure MPXH6400A 4 Sensors Freescale Semiconductor Pressure Transfer Function (MPXxx6400A) Normal Transfer Value: VOUT = VS x (0.002421 x P – 0.00842) ± Pressure Error x Temp. Factor x 0.002421 x VS VS = 5.0 ± 0.36 VDC Temperature Error Band MPXxx6400A Series 4.0 3.0 Temperature Error Factor Break Points 2.0 1.0 Temp 0.0 -40 -20 0 20 80 40 60 Temperature in C° 100 120 140 NOTE: The Temperature Multiplier is a linear response from 0°C to -40°C and from 85°C to 125°C - 40 0 to 85 125 Multiplier 3 1 1.75 Pressure Error Band Error Limits for Pressure ±5.5 (kPa) 6.0 5.0 4.0 Pressure Error (kPa) 3.0 2.0 1.0 0.0 -1.0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 320 340 360 380 400 -2.0 -3.0 -4.0 - 5.0 - 6.0 Pressure (in kPa) Pressure 20 to 400 (kPa) Error (Max) ±5.5 (kPa) MPXH6400A Sensors Freescale Semiconductor 5 Pressure PRESSURE (P1)/VACUUM (P2) SIDE IDENTIFICATION TABLE The two sides of the pressure sensor are designated as the Pressure (P1) side and the Vacuum (P2) side. The Pressure (P1) side is the side containing fluorosilicone gel, which protects the die from harsh media. The MPX pressure Part Number sensor is designed to operate with positive differential pressure applied, P1 > P2. The Pressure (P1) side may be identified by using the following table: Case Type Pressure (P1) Side Identifier MPXH6400AC6U 1317A Side with Port Attached MPXH6400AC6T1 1317A Side with Port Attached MPXHZ6400AC6T1 1317A Side with Port Attached 1369 Side with Port Attached MPXA6400AP SURFACE MOUNTING INFORMATION Minimum Recommended Footprint for Small Outline Package Surface mount board layout is a critical portion of the total design. The footprint for the surface mount packages must be the correct size to ensure proper solder connection interface between the board and the package. With the correct footprint, the packages will self align when subjected to a solder reflow process. It is always recommended to design boards with a solder mask layer to avoid bridging and shorting between solder pads. 0.100 TYP 8X 2.54 0.660 16.76 0.060 TYP 8X 1.52 0.300 7.62 inch mm 0.100 TYP 8X 2.54 SCALE 2:1 Figure 4. SOP Footprint (Case 1369) Minimum Recommended Footprint for Super Small Outline Package Surface mount board layout is a critical portion of the total design. The footprint for the semiconductor package must be the correct size to ensure proper solder connection interface between the board and the package. With the correct pad geometry, the packages will self-align when subjected to a solder reflow process. It is always recommended to fabricate boards with a solder mask layer to avoid bridging and/or shorting between solder pads, especially on tight tolerances and/or tight layouts. 0.050 1.27 TYP 0.387 9.83 0.150 3.81 0.027 TYP 8X 0.69 0.053 TYP 8X 1.35 inch mm Figure 5. SSOP Footprint (Case 1317A) MPXH6400A 6 Sensors Freescale Semiconductor Pressure PACKAGE DIMENSIONS PAGE 1 OF 2 CASE 1317A-04 ISSUE D SUPER SMALL OUTLINE PACKAGE MPXH6400A Sensors Freescale Semiconductor 7 Pressure PACKAGE DIMENSIONS PAGE 2 OF 2 CASE 1317A-04 ISSUE D SUPER SMALL OUTLINE PACKAGE MPXH6400A 8 Sensors Freescale Semiconductor Pressure PACKAGE DIMENSIONS PAGE 1 OF 2 CASE 1369-01 ISSUE B SMALL OUTLINE PACKAGE MPXH6400A Sensors Freescale Semiconductor 9 Pressure PACKAGE DIMENSIONS PAGE 2 OF 2 CASE 1369-01 ISSUE B SMALL OUTLINE PACKAGE MPXH6400A 10 Sensors Freescale Semiconductor How to Reach Us: Home Page: www.freescale.com Web Support: http://www.freescale.com/support USA/Europe or Locations Not Listed: Freescale Semiconductor, Inc. Technical Information Center, EL516 2100 East Elliot Road Tempe, Arizona 85284 1-800-521-6274 or +1-480-768-2130 www.freescale.com/support Europe, Middle East, and Africa: Freescale Halbleiter Deutschland GmbH Technical Information Center Schatzbogen 7 81829 Muenchen, Germany +44 1296 380 456 (English) +46 8 52200080 (English) +49 89 92103 559 (German) +33 1 69 35 48 48 (French) www.freescale.com/support Japan: Freescale Semiconductor Japan Ltd. Headquarters ARCO Tower 15F 1-8-1, Shimo-Meguro, Meguro-ku, Tokyo 153-0064 Japan 0120 191014 or +81 3 5437 9125 [email protected] Asia/Pacific: Freescale Semiconductor China Ltd. Exchange Building 23F No. 118 Jianguo Road Chaoyang District Beijing 100022 China +86 10 5879 8000 [email protected] For Literature Requests Only: Freescale Semiconductor Literature Distribution Center 1-800-441-2447 or +1-303-675-2140 Fax: +1-303-675-2150 [email protected] Information in this document is provided solely to enable system and software implementers to use Freescale Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. Freescale Semiconductor reserves the right to make changes without further notice to any products herein. Freescale Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters that may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”, must be validated for each customer application by customer’s technical experts. Freescale Semiconductor does not convey any license under its patent rights nor the rights of others. Freescale Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale Semiconductor product could create a situation where personal injury or death may occur. Should Buyer purchase or use Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was negligent regarding the design or manufacture of the part. Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. © Freescale Semiconductor, Inc. 2009. All rights reserved. MPXH6400A Rev. 4 11/2009