NL17SZ74 Single D Flip Flop The NL17SZ74 is a high performance, full function Edge triggered D Flip Flop, with all the features of a standard logic device such as the 74LCX74. • • • • • • • Extremely High Speed: tPD 2.6 ns (typical) at VCC = 5 V http://onsemi.com Designed for 1.65 V to 5.5 V VCC Operation 5 V Tolerant Inputs – Interface Capability with 5 V TTL Logic PR LVTTL Compatible LVCMOS Compatible 7 24 mA Balanced Output Sink and Source Capability Near Zero Static Supply Current (10 µA) Substantially Reduces System Power Requirements Replacement for NC7SZ74 • • Tiny Ultra Small Package Only 2.1 X 3.0 mm • High ESD Ratings: 2000 V Human Body Model • D 2 5 Q CP 1 3 Q 6 VCC = 8, GND = 4 CLR High ESD Ratings: 200 V Machine Model Chip Complexity: FET = 64 Figure 1. Logic Diagram TRUTH TABLE Inputs Outputs PR CLR CP D Q Q Operating Mode L H L H L L X X X X X X H L H L H H Asynchronous Set Asynchronous Clear Undetermined H H H H ↑ ↑ h l H L L H Load and Read Register H H ↑ X NC NC Hold H h L l NC X ↑ ↑ US8 CASE 493 US SUFFIX MARKING DIAGRAM = High Voltage Level = High Voltage Level One Setup Time Prior to the Low–to–High Clock Transition = Low Voltage Level = Low Voltage Level One Setup Time Prior to the Low–to–High Clock Transition = No Change = High or Low Voltage Level and Transitions are Acceptable = Low–to–High Transition = Not a Low–to–High Transition MH D MH = Specific Device Code D = Date Code For ICC reasons, DO NOT FLOAT Inputs PINOUT CP D Q GND 1 8 7 6 5 2 3 4 VCC PR CLR Q ORDERING INFORMATION Device NL17SZ74US Semiconductor Components Industries, LLC, 2002 May, 2002 – Rev. 2 1 Package Shipping US8 3000/Tape & Reel Publication Order Number: NL17SZ74/D NL17SZ74 MAXIMUM RATINGS Symbol Parameter Value Unit VCC DC Supply Voltage –0.5 to +7.0 V VI DC Input Voltage –0.5 to +7.0 V VO DC Output Voltage – Output in High or Low State (Note 1) –0.5 to VCC +0.5 V IIK DC Input Diode Current VI < GND –50 mA IOK DC Output Diode Current VO < GND –50 mA IO DC Output Sink Current ±50 mA ICC DC Supply Current Per Supply Pin ±100 mA IGND DC Ground Current Per Ground Pin ±100 mA TSTG Storage Temperature Range –65 to +150 °C TL Lead Temperature, 1 mm from Case for 10 Seconds 260 °C TJ Junction Temperature Under Bias +150 °C JA Thermal Resistance (Note 2) 250 °C/W PD Power Dissipation in Still Air at 85°C 250 mW MSL Moisture Sensitivity FR Flammability Rating Oxygen Index: 28 to 34 VESD ESD Withstand Voltage Human Body Model (Note 3) Machine Model (Note 4) Charged Device Model (Note 5) Level 1 UL 94 V–0 @ 0.125 in >2000 >200 N/A V Maximum Ratings are those values beyond which damage to the device may occur. Exposure to these conditions or conditions beyond those indicated may adversely affect device reliability. Functional operation under absolute maximum–rated conditions is not implied. Functional operation should be restricted to the Recommended Operating Conditions. 1. IO absolute maximum rating must be observed. 2. Measured with minimum pad spacing on an FR4 board, using 10 mm X 1 inch, 2 ounce copper trace with no air flow. 3. Tested to EIA/JESD22–A114–A. 4. Tested to EIA/JESD22–A115–A. 5. Tested to JESD22–C101–A. RECOMMENDED OPERATING CONDITIONS Symbol Parameter Min Max Unit 1.65 1.5 5.5 5.5 V VCC Supply Voltage Operating Data Retention Only VI Input Voltage (Note 6) 0 5.5 V VO Output Voltage (HIGH or LOW State) 0 VCC V TA Operating Free–Air Temperature –40 +85 °C t/∆V Input Transition Rise or Fall Rate 0 0 0 20 10 5.0 ns/V VCC = 2.5 V ±0.2 V VCC = 3.0 V ±0.3 V VCC = 5.0 V ±0.5 V 6. Unused inputs may not be left open. All inputs must be tied to a high–logic voltage level or a low–logic input voltage level. http://onsemi.com 2 NL17SZ74 DC ELECTRICAL CHARACTERISTICS Symbol Parameter VIH High–Level Input Voltage VIL Low–Level Input Voltage Condition 40C TA 85C TA = 25C VCC (V) Min Typ Max Min 1.65 0.75 VCC 0.75 VCC 2.3 to 5.5 0.7 VCC 0.7 VCC Max V 1.65 0.25 VCC 0.25 VCC 2.3 to 5.5 0.3 VCC 0.3 VCC VOH High Level Out High–Level Output ut Voltage VIN = VIL or VIL IOH = 100 A IOH = –3 3 mA IOH = –8 8 mA IOH = –12 12 mA IOH = –16 16 mA IOH = –24 24 mA IOH = –32 mA 1.65 to 5.5 1.65 2.3 2.7 3.0 3.0 4.5 VOL Low Level Output Low–Level Out ut Voltage VIN = VIH IOL = 100 A IOL = 3 mA IOL = 8 mA IOL = 12 mA IOL = 16 mA IOL = 24 mA IOL = 32 mA 1.65 to 5.5 1.65 2.3 2.7 3.0 3.0 4.5 IIN Input Leakage Current VIN = VCC or GND IOFF Power off Input Leakage Current 5.5V or VIN = GND ICC Quiescent Supply Current VIN = VCC or GND VCC – 0.1 1.29 1.9 2.2 2.4 2.3 3.8 VCC 1.52 2.1 2.4 2.7 2.5 4.0 VCC – 0.1 1.29 1.9 2.2 2.4 2.3 3.8 V V 0.1 0.24 0.3 0.4 0.4 0.55 0.55 0.1 0.24 0.3 0.4 0.4 0.55 0.55 V 5.5 0.1 1.0 A 0 1.0 10 A 5.5 1.0 10 A http://onsemi.com 3 0.008 0.10 0.12 0.15 0.19 0.30 0.30 Unit NL17SZ74 ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ Î ÎÎÎÎÎÎ ÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ Î ÎÎÎ ÎÎ Î ÎÎÎÎ ÎÎÎ ÎÎÎ Î ÎÎÎ ÎÎ ÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ Î ÎÎÎÎÎÎ ÎÎÎÎÎ Î ÎÎÎÎ ÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ Î ÎÎÎ ÎÎ Î ÎÎÎÎ ÎÎÎ ÎÎÎ Î ÎÎÎ ÎÎ ÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ Î ÎÎÎÎÎÎ ÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ Î ÎÎÎ ÎÎ Î ÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎ ÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎ AC ELECTRICAL CHARACTERISTICS (Input tr = tf = 3.0 ns) TA = 25°C Symbol fMAX Parameter Maximum Clock F Frequency (50% Duty Cycle) (Waveform 1) VCC (V) 1.8 ± 0.15 2.5 ± 0.2 3.3 ± 0.3 Test Conditions CL = 15 pF RD = 1 M S1 = Open 5.0 ± 0.5 tPLH, tPHL Propagation Delay, t Q or Q CP to (Waveform 1) 1.8 ± 0.15 2.5 ± 0.2 3.3 ± 0.3 5.0 ± 0.5 tPLH, tPHL Propagation Delay, PR or CLR tto Q or Q (Waveform 2) 1.8 ± 0.15 2.5 ± 0.2 3.3 ± 0.3 5.0 ± 0.5 tS Setup Time, D to t CP (Waveform 1) 1.8 ± 0.15 2.5 ± 0.2 3.3 ± 0.3 5.0 ± 0.5 tH Hold Time, D to t CP (Waveform 1) 1.8 ± 0.15 2.5 ± 0.2 3.3 ± 0.3 200 250 250 CL = 50 pF, RD = 500 , S1 = O Open 175 175 CL = 15 pF RD = 1 M S1 = Open 2.5 6.5 12.5 2.5 13 1.5 3.8 7.5 1.5 8.0 1.0 2.8 6.5 1.0 7.0 0.8 2.2 4.5 0.8 5.0 CL = 50 pF, RD = 500 , S1 = O Open 1.0 3.4 7.0 1.0 7.5 1.0 2.6 5.0 1.0 5.5 CL = 15 pF RD = 1 M S1 = Open 2.5 6.5 14 2.5 14.5 1.5 3.8 9.0 1.5 9.5 1.0 2.8 6.5 1.0 7.0 0.8 2.2 5.0 0.8 5.5 CL = 50 pF, RD = 500 , S1 = O Open 1.0 3.4 7.0 1.0 7.5 1.0 2.6 5.0 1.0 5.5 CL = 15 pF RD = 1 M S1 = Open 6.5 6.5 3.5 3.5 2.0 2.0 1.5 1.5 CL = 50 pF, RD = 500 , S1 = O Open 2.0 2.0 1.5 1.5 CL = 15 pF RD = 1 M S1 = Open 0.5 0.5 0.5 0.5 0.5 0.5 5.0 ± 0.5 tW Pulse Width, CP CLR, CP, CLR PR (Waveform 3) 1.8 ± 0.15 2.5 ± 0.2 3.3 ± 0.3 5.0 ± 0.5 tREC Recover Time PR CLR tto CP PR; (Waveform 3) 1.8 ± 0.15 2.5 ± 0.2 3.3 ± 0.3 0.5 0.5 0.5 0.5 0.5 0.5 CL = 15 pF RD = 1 M S1 = Open 6.0 6.0 4.0 4.0 3.0 3.0 2.0 2.0 CL = 50 pF, RD = 500 , S1 = O Open 3.0 3.0 2.0 2.0 CL = 15 pF RD = 1 M S1 = Open 8.0 8.0 4.5 4.5 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 5.0 ± 0.5 3.3 ± 0.3 5.0 ± 0.5 200 CL = 50 pF, RD = 500 , S1 = O Open 5.0 ± 0.5 3.3 ± 0.3 200 CL = 50 pF, RD = 500 , S1 = O Open Unit MHz 200 5.0 ± 0.5 3.3 ± 0.3 Max 150 5.0 ± 0.5 3.3 ± 0.3 Min 150 5.0 ± 0.5 3.3 ± 0.3 TA = –40 to 85°C Max 75 5.0 ± 0.5 3.3 ± 0.3 Typ 75 5.0 ± 0.5 3.3 ± 0.3 Min ns ns ns ns ns MHz 7. CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load. Average operating current can be obtained by the equation: ICC(OPR) = CPD VCC fin + ICC/2 (per flip–flop). CPD is used to determine the no–load dynamic power consumption; PD = CPD VCC2 fin + ICC VCC. http://onsemi.com 4 NL17SZ74 CAPACITANCE (Note 8) Typical Unit CIN Input Capacitance VCC = 5.5 V 7.0 pF COUT Output Capacitance VCC = 5.5 V 7.0 pF CPD Power Dissipation Capacitance (Note 9) Frequency = 10 MHz VCC = 3.3 V VCC = 5.0 V 16 21 pF Symbol Parameter Condition 8. TA = +25°C, f = 1 MHz 9. CPD is defined as the value of the internal equivalent capacitance which is derived from dynamic operating current consumption (I CCD) at no output loading and operating at 50% duty cycle. (See Figure 2) C PD is related to ICCD dynamic operating current by the expression: ICCD = CPD VCC fin + ICC(static). http://onsemi.com 5 NL17SZ74 Vcc D 50% 0V th ts Vcc tw CP 50% 0V fmax tPLH, tPHL VOH Q, Q 50% VOL WAVEFORM 1 – PROPAGATION DELAYS, SETUP AND HOLD TIMES tR = tF = 3.0 ns, 10% to 90%; f = 1 MHz; tW = 500 ns Vcc PR 50% 0V Vcc CLR 50% 0V tPLH tPHL Q 50% 50% VOL VOH tPLH Q 50% 50% tPHL WAVEFORM 2 – PROPAGATION DELAYS tR = tF = 3.0 ns, 10% to 90%; f = 1 MHz; tW = 500 ns Vcc tw PR, CLR 50% 0V trec Vcc 50% CP tw 0V WAVEFORM 3 – RECOVERY TIME tR = tF = 3.0 ns from 10% to 90%; f = 1 MHz; tw = 500 ns Output Reg: VOL ≤ 0.8 V, VOH ≥ 2.0 V Figure 2. AC Waveforms http://onsemi.com 6 NL17SZ74 VCC PULSE GENERATOR DUT RT CL RL Figure 3. Test Circuit DEVICE ORDERING INFORMATION Device Nomenclature Device Order Number NL17SZ74US Logic Circuit Indicator No. of Gates per Package Temp Range Identifier Technology Device Function Package Suffix Package Type Tape and Reel Size NL 1 7 SZ 74 US US8 178 mm, 3000 Unit http://onsemi.com 7 NL17SZ74 CAVITY TAPE TOP TAPE TAPE TRAILER (Connected to Reel Hub) NO COMPONENTS 160 mm MIN COMPONENTS TAPE LEADER NO COMPONENTS 400 mm MIN DIRECTION OF FEED Figure 4. Tape Ends for Finished Goods TAPE DIMENSIONS mm 4.00 1.50 TYP 4.00 2.00 1.75 3.50 0.25 0.30 8.00 + – 0.10 1 1.00 ± 0.25 TYP DIRECTION OF FEED Figure 5. US8 Reel Configuration/Orientation http://onsemi.com 8 NL17SZ74 t MAX 1.5 mm MIN (0.06 in) A 13.0 mm 0.2 mm (0.512 in 0.008 in) 50 mm MIN (1.969 in) 20.2 mm MIN (0.795 in) FULL RADIUS G Figure 6. Reel Dimensions REEL DIMENSIONS Tape Size T and R Suffix A Max G t Max 8 mm US 178 mm (7 in) 8.4 mm, + 1.5 mm, –0.0 (0.33 in + 0.059 in, –0.00) 14.4 mm (0.56 in) DIRECTION OF FEED BARCODE LABEL POCKET Figure 7. Reel Winding Direction http://onsemi.com 9 HOLE NL17SZ74 PACKAGE DIMENSIONS US8 US SUFFIX CASE 493–01 ISSUE O NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETERS 3. DIMENSION A" DOES NOT INCLUDE MOLD FLASH, PROTRUSION OR GATE BURR. MOLD FLASH. PROTRUSION AND GATE BURR SHALL NOT EXCEED 0.140 MM (0.0055") PER SIDE. 4. DIMENSION B" DOES NOT INCLUDE INTER-LEAD FLASH OR PROTRUSION. INTER-LEAD FLASH AND PROTRUSION SHALL NOT E3XCEED 0.140 (0.0055") PER SIDE. 5. LEAD FINISH IS SOLDER PLATING WITH THICKNESS OF 0.0076-0. 0203 MM. (300-800 mINCH). 6. ALL TOLERANCE UNLESS OTHERWISE SPECIFIED ±0.0508 (0.0002"). –X– A 8 J –Y– 5 DETAIL E B L 1 4 R S G P U C –T– SEATING PLANE H 0.10 (0.004) T K D N 0.10 (0.004) M T X Y R 0.10 TYP V M F DETAIL E 3.8 0.5 TYP ÉÉÉ ÉÉÉ ÉÉÉ ÉÉÉ ÉÉÉ ÉÉÉ ÉÉÉ ÉÉÉ ÉÉÉ ÉÉÉ 1.8 TYP 1.0 http://onsemi.com 10 0.3 TYP (mm) DIM A B C D F G H J K L M N P R S U V MILLIMETERS MIN MAX 1.90 2.10 2.20 2.40 0.60 0.90 0.17 0.25 0.20 0.35 0.50 BSC 0.40 REF 0.10 0.18 0.00 0.10 3.00 3.20 0 6 5 10 0.28 0.44 0.23 0.33 0.37 0.47 0.60 0.80 0.12 BSC INCHES MIN MAX 0.075 0.083 0.087 0.094 0.024 0.035 0.007 0.010 0.008 0.014 0.020 BSC 0.016 REF 0.004 0.007 0.000 0.004 0.118 0.126 0 6 5 10 0.011 0.017 0.009 0.013 0.015 0.019 0.024 0.031 0.005 BSC NL17SZ74 Notes http://onsemi.com 11 NL17SZ74 ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. PUBLICATION ORDERING INFORMATION Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303–675–2175 or 800–344–3860 Toll Free USA/Canada Fax: 303–675–2176 or 800–344–3867 Toll Free USA/Canada Email: [email protected] JAPAN: ON Semiconductor, Japan Customer Focus Center 4–32–1 Nishi–Gotanda, Shinagawa–ku, Tokyo, Japan 141–0031 Phone: 81–3–5740–2700 Email: [email protected] ON Semiconductor Website: http://onsemi.com For additional information, please contact your local Sales Representative. N. American Technical Support: 800–282–9855 Toll Free USA/Canada http://onsemi.com 12 NL17SZ74/D