NLX3G17 Product Preview Triple Non-Inverting Schmitt-Trigger Buffer The NLX3G17 MiniGatet is an advanced high-speed CMOS triple non-inverting Schmitt-trigger buffer in ultra-small footprint. The NLX3G17 input and output structures provide protection when voltages up to 7.0 V are applied, regardless of the supply voltage. The NLX3G17 can be used to enhance noise immunity or to square up slowly changing waveforms. Features •Designed for 1.65 V to 5.5 V VCC Operation •Low Power Dissipation: ICC = 1 mA (Max) at TA = 25°C •24 mA Balanced Output Source and Sink Capability @ VCC = 3.0 V •Balanced Propagation Delays •Overvoltage Tolerant (OVT) Input and Output Pins •Ultra-Small Packages •These are Pb-Free Devices IN A1 1 8 VCC OUT Y3 2 7 OUT Y1 http://onsemi.com MARKING DIAGRAMS KM 1 ULLGA8 1.45 x 1.0 CASE 613AA 1 ULLGA8 1.6 x 1.0 CASE 613AB AEM G ULLGA8 1.95 x 1.0 CASE 613AC AEM G 1 K or AE = Specific Device Code M = Date Code G = Pb-Free Package PIN ASSIGNMENT 3 IN A2 6 4 GND IN A3 5 OUT Y2 Figure 1. Pinout (Top View) IN A1 1 OUT Y1 IN A2 1 OUT Y2 IN A3 1 OUT Y3 1 IN A1 2 OUT Y3 3 IN A2 4 GND 5 OUT Y2 6 IN A3 7 OUT Y1 8 VCC FUNCTION TABLE A Y L H L H Figure 2. Logic Symbol ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 5 of this data sheet. This document contains information on a product under development. ON Semiconductor reserves the right to change or discontinue this product without notice. © Semiconductor Components Industries, LLC, 2008 March, 2008 - Rev. P1 1 Publication Order Number: NLX3G17/D NLX3G17 MAXIMUM RATINGS Symbol Value Unit VCC DC Supply Voltage -0.5 to +7.0 V VIN DC Input Voltage -0.5 to +7.0 V DC Output Voltage -0.5 to +7.0 V VIN < GND -50 mA VOUT < GND -50 mA VOUT Parameter IIK DC Input Diode Current IOK DC Output Diode Current IO DC Output Source/Sink Current ±50 mA ICC DC Supply Current Per Supply Pin ±100 mA IGND DC Ground Current per Ground Pin ±100 mA TSTG Storage Temperature Range -65 to +150 °C TL Lead Temperature, 1 mm from Case for 10 Seconds 260 °C TJ Junction Temperature Under Bias 150 °C MSL FR ILATCHUP Moisture Sensitivity Level 1 Flammability Rating Oxygen Index: 28 to 34 UL 94 V-0 @ 0.125 in Latchup Performance Above VCC and Below GND at 125 °C (Note 5) ±500 mA Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. Measured with minimum pad spacing on an FR4 board, using 10 mm-by-1 inch, 2 ounce copper trace no air flow. 2. Tested to EIA/JESD22-A114-A. 3. Tested to EIA/UESD22-A115-A. 4. Tested to JESD22-C101-A. 5. Tested to EIA / JESD78. RECOMMENDED OPERATING CONDITIONS Symbol Parameter Min Max Unit 1.65 5.5 V VCC Positive DC Supply Voltage VIN Digital Input Voltage 0 5.5 V Output Voltage 0 5.5 V -55 +125 °C 0 0 0 No Limit No Limit No Limit ns/V VOUT TA Operating Free-Air Temperature Dt/DV Input Transition Rise or Fall Rate VCC = 2.5 V ± 0.2 V VCC = 3.3 V ± 0.3 V VCC = 5.0 V ± 0.5 V http://onsemi.com 2 NLX3G17 DC ELECTRICAL CHARACTERISTICS TA = 25 5C TA = +855C TA = -555C to +1255C VCC (V) Min Typ Max Min Max Min Max Unit Positive Threshold Voltage 1.65 2.3 2.7 3.0 4.5 5.5 0.6 1.0 1.2 1.3 1.9 2.2 1.0 1.5 1.7 1.9 2.7 3.3 1.4 1.8 2.0 2.2 3.1 3.6 0.6 1.0 1.2 1.3 1.9 2.2 1.4 1.8 2.0 2.2 3.1 3.6 0.6 1.0 1.2 1.3 1.9 2.2 1.4 1.8 2.0 2.2 3.1 3.6 V VT- Negative Threshold Voltage 1.65 2.3 2.7 3.0 4.5 5.5 0.2 0.4 0.5 0.6 1.0 1.2 0.5 0.75 0.87 1.0 1.5 1.9 0.8 1.15 1.4 1.5 2.0 2.3 0.2 0.4 0.5 0.6 1.0 1.2 0.8 1.15 1.4 1.5 2.0 2.3 0.2 0.4 0.5 0.6 1.0 1.2 0.8 1.15 1.4 1.5 2.0 2.3 V VH Low-Level Input Voltage 1.65 2.3 2.7 3.0 4.5 5.5 0.1 0.25 0.3 0.4 0.6 0.7 0.48 0.75 0.83 0.93 1.2 1.4 0.9 1.1 1.15 1.2 1.5 1.7 0.1 0.25 0.3 0.4 0.6 0.7 0.9 1.1 1.15 1.2 1.5 1.7 0.1 0.25 0.3 0.4 0.6 0.7 0.9 1.1 1.15 1.2 1.5 1.7 V 1.65 - 5.5 VCC 0.1 VCC VCC 0.1 VCC 0.1 1.65 2.3 2.7 3.0 3.0 4.5 1.29 1.9 2.2 2.4 2.3 3.8 1.52 2.1 2.4 2.7 2.5 4.0 1.29 1.9 2.2 2.4 2.3 3.8 1.29 1.8 2.1 2.3 2.2 3.7 Symbol Parameter VT+ VOH VOL HighLevel Output Voltage Low-Level Output Voltage Conditions VIN w VT+MAX IOH = -100 mA VIN w VT+MAX IOH = -4 mA IOH = -8 mA IOH = -12 mA IOH = -16 mA IOH = -24 mA IOH = -32 mA VIN v VT-MIN IOL = 100 mA VIN v VT-MIN IOH = 4 mA IOH = 8 mA IOH = 12 mA IOH = 16 mA IOH = 24 mA IOH = 32 mA Input Leakage Current 0 v VIN v 5.5 V IOFF Power-Off Output Leakage Current VOUT = 5.5 V ICC Quiescent Supply Current 0 v VIN v VCC IIN V V 1.65 - 5.5 0 0.1 0.1 0.1 1.65 2.3 2.7 3.0 3.0 4.5 0.08 0.2 0.22 0.28 0.38 0.42 0.24 0.3 0.4 0.4 0.55 0.55 0.24 0.3 0.4 0.4 0.55 0.55 0.24 0.4 0.5 0.5 0.55 0.55 0 to 5.5 ±0.1 ±1.0 ±1.0 mA 0 1.0 10 10 mA 5.5 1.0 10 10 mA http://onsemi.com 3 NLX3G17 AC ELECTRICAL CHARACTERISTICS (Input tr = tf = 3.0 nS) Symbol tPLH, tPHL Parameter Propagation Delay Input A to Output VCC (V) Test Condition 2.3 to 2.7 3.0 to 3.6 4.5 to 5.5 TA = 25 5C TA = +855C TA = -555C to +1255C Min Typ Max Min Max Min Max Unit RL = 1 MW, CL = 15 pF 1.8 4.3 7.4 1.8 8.1 1.8 9.1 ns RL = 1 MW, CL = 15 pF 1.5 3.3 5.0 1.5 5.5 1.5 6.5 RL = 500 W, CL = 50 pF 1.8 4.0 5.0 1.8 6.6 1.8 7.6 RL = 1 MW, CL = 15 pF 1.0 2.7 4.1 1.0 4.5 1.0 5.5 RL = 500 W, CL = 50 pF 1.2 3.2 4.9 1.2 5.4 1.2 6.4 CIN Input Capacitance 5.5 VIN = 0 V or VCC 7.0 pF CPD Power Dissipation Capacitance (Note 6) 3.3 5.5 10 MHz VIN = 0 V or VCC 9.0 11 pF 6. CPD is defined as the value of the internal equivalent capacitance which is calculated from the dynamic operating current consumption without load. Average operating current can be obtained by the equation ICC(OPR) = CPD • VCC • fin + ICC. CPD is used to determine the no-load dynamic power consumption: PD = CPD • VCC2 • fin + ICC • VCC. VCC A or B 50% GND tPLH Y tPHL 50% VCC Figure 3. Switching Waveforms VCC PULSE GENERATOR DUT RT CL RT = ZOUT of pulse generator (typically 50 W) Figure 4. Test Circuit http://onsemi.com 4 RL NLX3G17 VT, TYPICAL INPUT THRESHOLD VOLTAGE (V) 4 3 (VT+) 2 VHtyp (VT-) 1 2 2.5 3 3.5 3.6 VCC, POWER SUPPLY VOLTAGE (V) VHtyp = (VT + typ) - (VT - typ) Figure 5. Typical Input Threshold, VT+, VTversus Power Supply Voltage VH VCC VT+ VT- VIN VCC VH VT+ VT- VIN GND GND VOH VOH VOUT Vout VOL VOL (a) A Schmitt-Trigger Squares Up Inputs With Slow Rise and Fall Times (b) A Schmitt-Trigger Offers Maximum Noise Immunity Figure 6. Typical Schmitt-Trigger Applications ORDERING INFORMATION Package Shipping† NLX3G17AMX1TCG ULLGA8, 1.95 x 1.0, 0.5P (Pb-Free) 3000 / Tape & Reel NLX3G17BMX1TCG ULLGA8, 1.6 x 1.0, 0.4P (Pb-Free) 3000 / Tape & Reel NLX3G17CMX1TCG ULLGA8, 1.45 x 1.0, 0.35P (Pb-Free) 3000 / Tape & Reel Device †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 5 NLX3G17 PACKAGE DIMENSIONS ULLGA8 1.45x1.0, 0.35P CASE 613AA-01 ISSUE A ÉÉÉ ÉÉÉ ÉÉÉ PIN ONE REFERENCE 0.10 C NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.30 mm FROM THE TERMINAL TIP. 4. A MAXIMUM OF 0.05 PULL BACK OF THE PLATED TERMINAL FROM THE EDGE OF THE PACKAGE IS ALLOWED. A B D E DIM A A1 b D E e L L1 TOP VIEW 0.10 C 0.05 C A 8X 0.05 C SEATING PLANE SIDE VIEW MOUNTING FOOTPRINT SOLDERMASK DEFINED* C A1 MILLIMETERS MIN MAX --0.40 0.00 0.05 0.15 0.25 1.45 BSC 1.00 BSC 0.35 BSC 0.25 0.35 0.30 0.40 7X 0.48 8X 0.22 e/2 e 1 7X L NOTE 4 4 1.18 L1 0.53 8 5 8X PKG OUTLINE b 0.05 C 0.35 PITCH DIMENSIONS: MILLIMETERS 0.10 C A B BOTTOM VIEW 1 *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. NOTE 3 http://onsemi.com 6 NLX3G17 PACKAGE DIMENSIONS ULLGA8 1.6x1.0, 0.4P CASE 613AB-01 ISSUE A PIN ONE REFERENCE 0.10 C 0.10 C NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.30 mm FROM THE TERMINAL TIP. 4. A MAXIMUM OF 0.05 PULL BACK OF THE PLATED TERMINAL FROM THE EDGE OF THE PACKAGE IS ALLOWED. A B D ÉÉÉ ÉÉÉ ÉÉÉ E DIM A A1 b D E e L L1 TOP VIEW 0.05 C A 8X 0.05 C SEATING PLANE SIDE VIEW MOUNTING FOOTPRINT SOLDERMASK DEFINED* C A1 MILLIMETERS MIN MAX --0.40 0.00 0.05 0.15 0.25 1.60 BSC 1.00 BSC 0.40 BSC 0.25 0.35 0.30 0.40 7X 0.49 8X 0.26 e/2 e 1 7X L NOTE 4 4 1.24 L1 0.53 8 5 8X b 0.05 C 0.40 PITCH DIMENSIONS: MILLIMETERS 0.10 C A B BOTTOM VIEW 1 PKG OUTLINE *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. NOTE 3 http://onsemi.com 7 NLX3G17 PACKAGE DIMENSIONS ULLGA8 1.95x1.0, 0.5P CASE 613AC-01 ISSUE A PIN ONE REFERENCE 0.10 C NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.30 mm FROM THE TERMINAL TIP. 4. A MAXIMUM OF 0.05 PULL BACK OF THE PLATED TERMINAL FROM THE EDGE OF THE PACKAGE IS ALLOWED. A B D ÉÉÉÉ ÉÉÉÉ ÉÉÉÉ E DIM A A1 b D E e L L1 TOP VIEW 0.10 C 0.05 C MILLIMETERS MIN MAX --0.40 0.00 0.05 0.15 0.25 1.95 BSC 1.00 BSC 0.50 BSC 0.25 0.35 0.30 0.40 A 8X 0.05 C MOUNTING FOOTPRINT SOLDERMASK DEFINED* SEATING PLANE SIDE VIEW 7X C A1 0.49 8X 0.30 e/2 e 7X L NOTE 4 4 1 1.24 L1 0.53 8 5 8X BOTTOM VIEW b 0.10 C A B 0.05 C 1 PKG OUTLINE 0.50 PITCH DIMENSIONS: MILLIMETERS *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. NOTE 3 MiniGate is a trademark of Semiconductor Components Industries, LLC (SCILLC). ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 http://onsemi.com 8 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NLX3G17/D