TECCOR P3100S

SIDACtor Device
SIDACtor Device
DO-214AA SIDACtor solid state protection devices protect telecommunications equipment
such as modems, line cards, fax machines, and other CPE.
SIDACtor devices are used to enable equipment to meet various regulatory requirements
including GR 1089, ITU K.20, K.21 and K.45, IEC 60950, UL 60950, and TIA/EIA-IS-968
(formerly known as FCC Part 68).
Electrical Parameters
Part
Number *
VDRM
Volts
VS
Volts
VT
Volts
IDRM
µAmps
IS
mAmps
IT
Amps
IH
mAmps
CO
pF
P0080S_
6
25
4
5
800
2.2
50
100
P0300S_
25
40
4
5
800
2.2
50
110
P0640S_
58
77
4
5
800
2.2
150
50
P0720S_
65
88
4
5
800
2.2
150
50
P0900S_
75
98
4
5
800
2.2
150
50
P1100S_
90
130
4
5
800
2.2
150
40
P1300S_
120
160
4
5
800
2.2
150
40
P1500S_
140
180
4
5
800
2.2
150
40
P1800S_
170
220
4
5
800
2.2
150
30
P2300S_
190
260
4
5
800
2.2
150
30
P2600S_
220
300
4
5
800
2.2
150
30
P3100S_
275
350
4
5
800
2.2
150
30
P3500S_
320
400
4
5
800
2.2
150
30
* For individual “SA”, “SB”, and “SC” surge ratings, see table below.
General Notes:
• All measurements are made at an ambient temperature of 25 °C. IPP applies to -40 °C through +85 °C temperature range.
• IPP is a repetitive surge rating and is guaranteed for the life of the product.
• Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities.
• VDRM is measured at IDRM.
• VS is measured at 100 V/µs.
• Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request.
• Off-state capacitance is measured at 1 MHz with a 2 V bias and is a typical value for “SA” and “SB” product. “SC” capacitance is
approximately 2x the listed value. The off-state capacitance of the P0080SB is equal to the “SC” device.
Surge Ratings
Series
IPP
2x10 µs
Amps
IPP
8x20 µs
Amps
A
150
150
90
50
45
20
500
B
250
250
150
100
80
30
500
C
500
400
200
150
100
50
500
http://www.teccor.com
+1 972-580-7777
IPP
10x160 µs
Amps
IPP
10x560 µs
Amps
2-4
IPP
10x1000 µs
Amps
ITSM
60 Hz
Amps
di/dt
Amps/µs
© 2002 Teccor Electronics
SIDACtor® Data Book and Design Guide
SIDACtor Device
Package
Symbol
Value
Unit
DO-214AA
TJ
Operating Junction Temperature Range
-40 to +150
°C
TS
Storage Temperature Range
-65 to +150
°C
90
°C/W
RqJA
Parameter
Thermal Resistance: Junction to Ambient
IPP – Peak Pulse Current – %IPP
+I
+I
IITT
ISS
IH
IDRM
-V
-V
+V
+V
V
VTT
V
VDRM
DRM
V
VS
S
Peak
Value
100
tr = rise time to peak value
td = decay time to half value
Waveform = tr x td
50
Half Value
0
0
tr
td
t – Time (µs)
-I
-I
14
12
10
IH
8
6
25 °C
4
2
IH (TC = 25 °C)
tr x td Pulse Wave-form
Ratio of
Percent of VS Change – %
V-I Characteristics
0
-4
2.0
1.8
1.6
1.4
25 °C
1.2
1.0
0.8
0.6
0.4
-40 -20 0
-6
-8
-40 -20
0
20 40 60 80 100 120 140 160
Case Temperature (TC) – °C
20 40 60 80 100 120 140 160
Junction Temperature (TJ) – °C
Normalized VS Change versus Junction Temperature
© 2002 Teccor Electronics
SIDACtor® Data Book and Design Guide
Normalized DC Holding Current versus Case Temperature
2-5
http://www.teccor.com
+1 972-580-7777
Data Sheets
Thermal Considerations