TI SN74AVCBH164245KR

SCES393A − JUNE 2002 − REVISED MAY 2004
D Member of the Texas Instruments
D
D
D
D
D
D Ioff Supports Partial-Power-Down Mode
Widebus Family
DOC Circuitry Dynamically Changes
Output Impedance, Resulting in Noise
Reduction Without Speed Degradation
Dynamic Drive Capability Is Equivalent to
Standard Outputs With IOH and IOL of
±24 mA at 2.5-V VCC
Control Inputs VIH/VIL Levels are
Referenced to VCCB Voltage
If Either VCC Input Is at GND, Both Ports
Are in the High-Impedance State
Overvoltage-Tolerant Inputs/Outputs Allow
Mixed-Voltage-Mode Data Communications
D
D
D
D
Operation
Fully Configurable Dual-Rail Design Allows
Each Port to Operate Over the Full 1.4-V to
3.6-V Power-Supply Range
Bus Hold on Data Inputs Eliminates the
Need for External Pullup / Pulldown
Resistors
Latch-Up Performance Exceeds 100 mA Per
JESD 78, Class II
ESD Protection Exceeds JESD 22
− 2000-V Human-Body Model (A114-A)
− 200-V Machine Model (A115-A)
− 1000-V Charged-Device Model (C101)
description/ordering information
This 16-bit (dual-octal) noninverting bus transceiver uses two separate configurable power-supply rails. The
A-port is designed to track VCCA. VCCA accepts any supply voltage from 1.4 V to 3.6 V. The B-port is designed
to track VCCB. VCCB accepts any supply voltage from 1.4 V to 3.6 V. This allows for universal low-voltage
bidirectional translation between any of the 1.5-V, 1.8-V, 2.5-V, and 3.3-V voltage nodes.
The SN74AVCBH164245 is designed for asynchronous communication between data buses. The device
transmits data from the A bus to the B bus or from the B bus to the A bus, depending on the logic level at the
direction-control (DIR) input. The output-enable (OE) input can be used to disable the outputs so the buses are
effectively isolated.
The SN74AVCBH164245 is designed so that the control pins (1DIR, 2DIR, 1OE, and 2OE) are supplied by
VCCB.
Active bus-hold circuitry is provided to hold unused or floating data inputs at a valid logic level. Use of pullup
or pulldown resistors with the bus-hold circuitry is not recommended.
To ensure the high-impedance state during power up or power down, OE should be tied to VCCB through a pullup
resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.
This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs,
preventing damaging current backflow through the device when it is powered down. If either VCC input is at GND,
both ports are in the high-impedance state.
ORDERING INFORMATION
PACKAGE†
TA
−40°C
−40
C to 85
85°C
C
ORDERABLE
PART NUMBER
TOP-SIDE
MARKING
TSSOP − DGG
Tape and reel
SN74AVCBH164245GR
AVCBH164245
TVSOP − DGV
Tape and reel
SN74AVCBH164245VR
WBH4245
VFBGA − GQL
Tape and reel
SN74AVCBH164245KR
WBH4245
† Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines
are available at www.ti.com/sc/package.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
DOC and Widebus are trademarks of Texas Instruments.
Copyright  2004, Texas Instruments Incorporated
!"#$%! & '("")% $& ! *(+,'$%! -$%).
"!-('%& '!!"# %! &*)''$%!& *)" %/) %)"#& ! )0$& &%"(#)%&
&%$-$"- 1$""$%2. "!-('%! *"!')&&3 -!)& !% )')&&$",2 ',(-)
%)&%3 ! $,, *$"$#)%)"&.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
SCES393A − JUNE 2002 − REVISED MAY 2004
terminal assignments
DGG OR DGV PACKAGE
(TOP VIEW)
1DIR
1B1
1B2
GND
1B3
1B4
VCCB
1B5
1B6
GND
1B7
1B8
2B1
2B2
GND
2B3
2B4
VCCB
2B5
2B6
GND
2B7
2B8
2DIR
GQL PACKAGE
(TOP VIEW)
1
2
3
4
5
1
48
2
47
3
46
4
45
5
44
6
43
7
42
8
41
9
40
10
39
11
38
12
37
13
36
14
35
15
34
16
33
17
32
18
31
19
30
20
29
21
28
22
27
23
26
24
25
terminal assignments
6
1
A
B
C
D
E
F
G
1OE
1A1
1A2
GND
1A3
1A4
VCCA
1A5
1A6
GND
1A7
1A8
2A1
2A2
GND
2A3
2A4
VCCA
2A5
2A6
GND
2A7
2A8
2OE
2
3
6
A
1DIR
NC
NC
NC
NC
1OE
1B2
1B1
GND
GND
1A1
1A2
C
1B4
1B3
1B5
VCCA
GND
1A4
1B6
VCCB
GND
1A3
D
1A5
1A6
E
1B8
1B7
1A7
1A8
F
2B1
2B2
2A2
2A1
G
2B3
2B4
GND
GND
2A4
2A3
H
2B5
2B6
VCCA
GND
2A6
2A5
2A8
2A7
NC
NC
2OE
H
J
2B7
2B8
J
K
2DIR
NC
NC
2
5
B
VCCB
GND
K
4
NC − No internal connection
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SCES393A − JUNE 2002 − REVISED MAY 2004
FUNCTION TABLE
(each 8-bit section)
INPUTS
OE
DIR
OPERATION
L
L
B data to A bus
L
H
A data to B bus
H
X
Isolation
logic diagram (positive logic)
1DIR
1
2DIR
48
1A1
25
1OE
47
2A1
2
24
2OE
36
13
1B1
2B1
To Seven Other Channels
To Seven Other Channels
Pin numbers shown are for the DGG and DGV packages.
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage range, VCCA and VCCB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 4.6 V
Input voltage range, VI (see Note 1): I/O ports (A port) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 4.6 V
I/O ports (B port) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 4.6 V
Control inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 4.6 V
Voltage range applied to any output in the high-impedance or power-off state, VO
(see Note 1): (A port) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 4.6 V
(B port) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 4.6 V
Voltage range applied to any output in the high or low state, VO
(see Notes 1 and 2): (A port) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to VCCA + 0.5 V
(B port) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to VCCB + 0.5 V
Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −50 mA
Output clamp current, IOK (VO < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −50 mA
Continuous output current, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±50 mA
Continuous current through VCCA, VCCB, or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±100 mA
Package thermal impedance, θJA (see Note 3): DGG package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70°C/W
DGV package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58°C/W
GQL package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28°C/W
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. The input and output negative-voltage ratings may be exceeded if the input and output current ratings are observed.
2. The output positive-voltage rating may be exceeded up to 4.6 V maximum if the output current rating is observed.
3. The package thermal impedance is calculated in accordance with JESD 51-7.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
SCES393A − JUNE 2002 − REVISED MAY 2004
recommended operating conditions (see Notes 4 through 6)
VCCI
VCCA
VCCB
VCCO
MIN
MAX
Supply voltage
1.4
3.6
V
Supply voltage
1.4
3.6
V
VCCI × 0.65
1.7
1.4 V to 1.95 V
VIH
High-level input
voltage
Data inputs
1.95 V to 2.7 V
2.7 V to 3.6 V
VIL
Data inputs
VCCI × 0.35
0.7
1.95 V to 2.7 V
2.7 V to 3.6 V
High-level input
voltage
Control inputs
(Referenced to VCCB)
VCCB × 0.65
1.7
1.95 V to 2.7 V
2.7 V to 3.6 V
VI
VO
IOH
IOL
∆t/∆v
Low-level input
voltage
Control inputs
(Referenced to VCCB)
VCCB × 0.35
0.7
1.95 V to 2.7 V
2.7 V to 3.6 V
V
0.8
Input voltage
Output voltage
V
2
1.4 V to 1.95 V
VIL
V
0.8
1.4 V to 1.95 V
VIH
V
2
1.4 V to 1.95 V
Low-level input
voltage
UNIT
0
3.6
V
Active state
0
3-state
0
VCCO
3.6
V
High-level output current
Low-level output current
1.4 V to 1.6 V
−2
1.65 V to 1.95 V
−4
2.3 V to 2.7 V
−8
3 V to 3.6 V
−12
1.4 V to 1.6 V
2
1.65 V to 1.95 V
4
2.3 V to 2.7 V
8
3 V to 3.6 V
12
Input transition rise or fall rate
5
mA
mA
ns/V
TA
Operating free-air temperature
−40
85
°C
NOTES: 4. VCCI is the VCC associated with the data input port.
5. VCCO is the VCC associated with the output port.
6. All unused data inputs of the device must be held at VCCI or GND to ensure proper device operation. Refer to the TI application report,
Implications of Slow or Floating CMOS Inputs, literature number SCBA004.
4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SCES393A − JUNE 2002 − REVISED MAY 2004
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted) (see Note 7)
PARAMETER
VOH
VOL
II
Control inputs
IBHL‡
TEST CONDITIONS
IOH = −100 µA
IOH = −2 mA
VI = VIH
VI = VIH
IOH = −4 mA
IOH = −8 mA
VCCB
1.4 V to 3.6 V
1.4 V to 3.6 V
VI = VIH
VI = VIH
1.65 V
1.65 V
1.2
2.3 V
2.3 V
1.75
IOH = −12 mA
IOH = 100 µA
VI = VIH
VI = VIL
3V
3V
2.3
IOH = 2 mA
IOH = 4 mA
VI = VIL
VI = VIL
IOH = 8 mA
IOH = 12 mA
VI = VIL
VI = VIL
VI = VCCB or GND
VI = 0.49 V
VI = 0.57 V
VI = 0.7 V
VI = 1.07 V
VI = 1.7 V
1.4 V to 3.6 V
IBHHO#
VI = 0 to VCC
VI = 0 to VCC
B port
VI or VO = 0 to 3.6 V
MAX
1.4 V to 3.6 V
0.2
1.4 V
0.35
1.65 V
1.65 V
0.45
2.3 V
2.3 V
0.55
3V
1.4 V to 3.6 V
UNIT
V
1.4 V
3V
0.7
3.6 V
±2.5
1.4 V
1.4 V
1.65 V
1.65 V
25
2.3 V
2.3 V
45
75
V
µA
11
3V
3V
1.4 V
1.4 V
1.65 V
1.65 V
−25
2.3 V
2.3 V
−45
3V
3V
−75
µA
A
−11
1.6 V
1.6 V
100
1.95 V
1.95 V
200
2.7 V
2.7 V
300
3.6 V
3.6 V
525
1.6 V
1.6 V
−100
1.95 V
1.95 V
−200
2.7 V
2.7 V
−300
3.6 V
3.6 V
−525
µA
A
µA
A
A
µA
0V
0 to 3.6 V
±10
0 to 3.6 V
0V
±10
A port
Ioff
TYP†
VCCO−0.2 V
1.05
1.4 V
VI = 2 V
IBHLO¶
MIN
1.4 V
VI = 0.8 V
VI = 0.91 V
IBHH§
VCCA
µA
A
† All typical values are at TA = 25°C.
‡ The bus-hold circuit can sink at least the minimum low sustaining current at VIL max. IBHL should be measured after lowering VIN to GND and
then raising it to VIL max.
§ The bus-hold circuit can source at least the minimum high sustaining current at VIH min. IBHH should be measured after raising VIN to VCC and
then lowering it to VIH min.
¶ An external driver must source at least IBHLO to switch this node from low to high.
# An external driver must sink at least IBHHO to switch this node from high to low.
NOTE 7: VCCO is the VCC associated with the output port.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
SCES393A − JUNE 2002 − REVISED MAY 2004
electrical characteristics over recommended operating free-air temperature range (continued)
(unless otherwise noted) (see Notes 8 and 9)
PARAMETER
TEST CONDITIONS
OE = VIH
A or B ports
IOZ‡
VO = VCCO or GND,
VI = VCCI or GND
B port
A port
ICCA
VI = VCCI or GND,
ICCB
VI = VCCI or GND,
Ci
Control inputs
Cio
A or B ports
OE = don’t care
IO = 0
IO = 0
VI = 3.3 V or GND
VO = 3.3 V or GND
MIN
TYP†
MAX
UNIT
VCCA
VCCB
3.6 V
3.6 V
±12.5
0V
3.6 V
±12.5
3.6 V
0V
±12.5
1.6 V
1.6 V
20
1.95 V
1.95 V
20
2.7 V
2.7 V
30
0V
3.6 V
−40
3.6 V
0V
40
3.6 V
3.6 V
40
1.6 V
1.6 V
20
1.95 V
1.95 V
20
2.7 V
2.7 V
30
0V
3.6 V
40
3.6 V
0V
−40
3.6 V
3.6 V
40
3.3 V
3.3 V
4
pF
3.3 V
3.3 V
5
pF
µA
A
µA
µA
A
† All typical values are at TA = 25°C.
‡ For I/O ports, the parameter IOZ includes the input leakage current.
NOTES: 8. VCCO is the VCC associated with the output port.
9. VCCI is the VCC associated with the input port.
switching characteristics over recommended operating free-air temperature range,
VCCA = 1.5 V ± 0.1 V (see Figure 2)
PARAMETER
tpd
ten
tdis
6
FROM
(INPUT)
TO
(OUTPUT)
A
B
VCCB = 1.5 V
± 0.1 V
VCCB = 1.8 V
± 0.15 V
VCCB = 2.5 V
± 0.2 V
VCCB = 3.3 V
± 0.3 V
MIN
MAX
MIN
MAX
MIN
MAX
MIN
MAX
B
1.7
6.7
1.9
6.3
1.8
5.5
1.7
5.8
A
1.8
6.8
2.2
7.4
2.1
7.6
2.1
7.3
OE
A
2.5
8.4
2.4
7.4
2.1
5.2
1.9
4.2
OE
B
2.1
9
2.9
9.8
3.2
10
3
9.8
OE
A
2.2
6.9
2.3
6.1
1.3
3.6
1.3
3
OE
B
2.1
7.1
2.3
6.4
1.7
5.1
1.6
4.8
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
UNIT
ns
ns
ns
SCES393A − JUNE 2002 − REVISED MAY 2004
switching characteristics over recommended operating free-air temperature range,
VCCA = 1.8 V ± 0.15 V (see Figure 2)
PARAMETER
tpd
ten
tdis
FROM
(INPUT)
TO
(OUTPUT)
A
B
VCCB = 1.5 V
± 0.1 V
VCCB = 1.8 V
± 0.15 V
VCCB = 2.5 V
± 0.2 V
VCCB = 3.3 V
± 0.3 V
MIN
MAX
MIN
MAX
MIN
MAX
MIN
MAX
B
1.7
6.4
1.8
6
1.7
4.7
1.6
4.3
A
1.4
5.5
1.8
6
1.8
5.8
1.8
5.5
OE
A
2.6
8.5
2.5
7.5
2.2
5.3
1.9
4.2
OE
B
1.8
7.6
2.6
7.7
2.6
7.6
2.6
7.4
OE
A
2.3
7
2.3
6.1
1.3
3.6
1.3
3
OE
B
1.8
7
2.5
6.3
1.8
4.7
1.7
4.4
UNIT
ns
ns
ns
switching characteristics over recommended operating free-air temperature range,
VCCA = 2.5 V ± 0.2 V (see Figure 2)
PARAMETER
tpd
ten
tdis
FROM
(INPUT)
TO
(OUTPUT)
A
B
B
A
OE
VCCB = 1.5 V
± 0.1 V
MIN
VCCB = 1.8 V
± 0.15 V
VCCB = 2.5 V
± 0.2 V
VCCB = 3.3 V
± 0.3 V
MAX
MIN
MAX
MIN
MAX
MIN
MAX
1.6
6
1.8
5.6
1.5
4
1.4
3.4
1.3
4.6
1.7
4.4
1.5
4
1.4
3.7
A
3.1
8.5
2.5
7.5
2.2
5.3
1.9
4.2
OE
B
1.7
5.7
2.2
5.5
2.2
5.3
2.2
5.1
OE
A
2.4
7
3
6.1
1.4
3.6
1.2
3
OE
B
1.2
5.8
1.9
5
1.4
3.6
1.3
3.3
UNIT
ns
ns
ns
switching characteristics over recommended operating free-air temperature range,
VCCA = 3.3 V ± 0.3 V (see Figure 2)
PARAMETER
tpd
ten
tdis
FROM
(INPUT)
TO
(OUTPUT)
A
B
VCCB = 1.5 V
± 0.1 V
VCCB = 1.8 V
± 0.15 V
VCCB = 2.5 V
± 0.2 V
VCCB = 3.3 V
± 0.3 V
MIN
MAX
MIN
MAX
MIN
MAX
MIN
MAX
B
1.5
5.9
1.7
5.4
1.5
3.7
1.4
3.1
A
1.3
4.5
1.6
3.8
1.5
3.3
1.4
3.1
OE
A
2.6
8.3
2.5
7.4
2.2
5.2
1.9
4.1
OE
B
1.6
4.9
2
4.5
2
4.3
1.9
4.1
OE
A
2.3
7
3
6
1.3
3.5
1.2
3.5
OE
B
1.3
6.9
2.1
5.5
1.6
3.8
1.5
3.5
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
UNIT
ns
ns
ns
7
SCES393A − JUNE 2002 − REVISED MAY 2004
operating characteristics, VCCA and VCCB = 3.3 V, TA = 25°C
PARAMETER
CpdA
(VCCA)
CpdB
(VCCB)
TEST CONDITIONS
TYP
Outputs enabled
Power dissipation capacitance per transceiver,
A port input, B port output
UNIT
14
Outputs disabled
7
CL = 0,
f = 10 MHz
Power dissipation capacitance per transceiver,
B port input, A port output
Outputs enabled
20
Outputs disabled
7
Power dissipation capacitance per transceiver,
A port input, B port output
Outputs enabled
20
Power dissipation capacitance per transceiver,
B port input, A port output
Outputs enabled
Outputs disabled
pF
7
CL = 0,
f = 10 MHz
14
Outputs disabled
pF
7
output description
The DOC  circuitry is implemented, which, during the transition, initially lowers the output impedance to
effectively drive the load and, subsequently, raises the impedance to reduce noise. Figure 1 shows typical VOL
vs IOL and VOH vs IOH curves to illustrate the output impedance and drive capability of the circuit. At the
beginning of the signal transition, the DOC circuit provides a maximum dynamic drive that is equivalent to a
high-drive standard-output device. For more information, refer to the TI application reports, AVC Logic Family
Technology and Applications, literature number SCEA006, and Dynamic Output Control (DOC ) Circuitry
Technology and Applications, literature number SCEA009.
3.2
TA = 25°C
Process = Nominal
− Output Voltage − V
2.4
VCC = 3.3 V
2.0
1.6
VCC = 2.5 V
1.2
OH
VCC = 1.8 V
0.8
V
VOL − Output Voltage − V
2.8
2.8
2.4
2.0
1.6
1.2
0.8
0.4
0.4
0
17
34
51
68
85 102 119
IOL − Output Current − mA
136
153
170
TA = 25°C
Process = Nominal
VCC = 3.3 V
VCC = 2.5 V
−160 −144 −128 −112 −96 −80 −64 −48
IOH − Output Current − mA
Figure 1. Typical Output Voltage vs Output Current
8
POST OFFICE BOX 655303
VCC = 1.8 V
• DALLAS, TEXAS 75265
−32 −16
0
SCES393A − JUNE 2002 − REVISED MAY 2004
PARAMETER MEASUREMENT INFORMATION
2 × VCCO
S1
RL
From Output
Under Test
Open
GND
CL
(see Note A)
TEST
S1
tpd
tPLZ/tPZL
tPHZ/tPZH
Open
2 × VCCO
GND
RL
tw
LOAD CIRCUIT
VCCI
VCCI/2
Input
VCCO
1.5 V ± 0.1 V
1.8 V ± 0.15 V
2.5 V ± 0.2 V
3.3 V ± 0.3 V
CL
RL
15 pF
30 pF
30 pF
30 pF
2 kΩ
1 kΩ
500 Ω
500 Ω
VTP
0.1 V
0.15 V
0.15 V
0.3 V
VCCI/2
0V
VOLTAGE WAVEFORMS
PULSE DURATION
VCCB
Output
Control
(low-level
enabling)
VCCB/2
VCCB/2
0V
tPZL
VCCI
Input
VCCI/2
VCCI/2
0V
tPLH
Output
VOH
VCCO/2
VOL
VCCO/2
VCCO
Output
Waveform 1
S1 at 2 × VCCO
(see Note B)
tPHL
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
tPLZ
VCCO/2
tPZH
Output
Waveform 2
S1 at GND
(see Note B)
VOL + VTP
VOL
tPHZ
VCCO/2
VOH − VTP
VOH
0V
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES
NOTES: A. CL includes probe and jig capacitance.
B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control.
C. All input pulses are supplied by generators having the following characteristics: PRRv10 MHz, ZO = 50 Ω, dv/dt ≥ 1 V/ns,
dv/dt ≥1 V/ns.
D. The outputs are measured one at a time, with one transition per measurement.
E. tPLZ and tPHZ are the same as tdis.
F. tPZL and tPZH are the same as ten.
G. tPLH and tPHL are the same as tpd.
H. VCCI is the VCC associated with the input port.
I. VCCO is the VCC associated with the output port.
Figure 2. Load Circuit and Voltage Waveforms
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
9
MECHANICAL DATA
MPDS006C – FEBRUARY 1996 – REVISED AUGUST 2000
DGV (R-PDSO-G**)
PLASTIC SMALL-OUTLINE
24 PINS SHOWN
0,40
0,23
0,13
24
13
0,07 M
0,16 NOM
4,50
4,30
6,60
6,20
Gage Plane
0,25
0°–8°
1
0,75
0,50
12
A
Seating Plane
0,15
0,05
1,20 MAX
PINS **
0,08
14
16
20
24
38
48
56
A MAX
3,70
3,70
5,10
5,10
7,90
9,80
11,40
A MIN
3,50
3,50
4,90
4,90
7,70
9,60
11,20
DIM
4073251/E 08/00
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion, not to exceed 0,15 per side.
Falls within JEDEC: 24/48 Pins – MO-153
14/16/20/56 Pins – MO-194
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MECHANICAL DATA
MTSS003D – JANUARY 1995 – REVISED JANUARY 1998
DGG (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
48 PINS SHOWN
0,27
0,17
0,50
48
0,08 M
25
6,20
6,00
8,30
7,90
0,15 NOM
Gage Plane
1
0,25
24
0°– 8°
A
0,75
0,50
Seating Plane
0,15
0,05
1,20 MAX
PINS **
0,10
48
56
64
A MAX
12,60
14,10
17,10
A MIN
12,40
13,90
16,90
DIM
4040078 / F 12/97
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold protrusion not to exceed 0,15.
Falls within JEDEC MO-153
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright  2004, Texas Instruments Incorporated