SN74CBT3253 DUAL 1-OF-4 FET MULTIPLEXER/DEMULTIPLEXER SCDS018I – MAY 1995 – REVISED MAY 1998 D D D D D, DB, DBQ, DGV, OR PW PACKAGE (TOP VIEW) Functionally Equivalent to QS3253 5-Ω Switch Connection Between Two Ports TTL-Compatible Input Levels Package Options Include Plastic Small-Outline (D), Shrink Small-Outline (DB, DBQ), Thin Very Small-Outline (DGV), and Thin Shrink Small-Outline (PW) Packages 1OE S1 1B4 1B3 1B2 1B1 1A GND description 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 VCC 2OE S0 2B4 2B3 2B2 2B1 2A The SN74CBT3253 is a dual 1-of-4 high-speed TTL-compatible FET multiplexer/demultiplexer. The low on-state resistance of the switch allows connections to be made with minimal propagation delay. 1OE, 2OE, S0, and S1 select the appropriate B output for the A-input data. The SN74CBT3253 is characterized for operation from –40°C to 85°C. FUNCTION TABLE (each multiplexer/demultiplexer) INPUTS FUNCTION OE S1 L L L A port = B1 port L L H A port = B2 port L H L A port = B3 port L H H A port = B4 port H X X Disconnect S0 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 1998, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 SN74CBT3253 DUAL 1-OF-4 FET MULTIPLEXER/DEMULTIPLEXER SCDS018I – MAY 1995 – REVISED MAY 1998 logic diagram (positive logic) 1A 6 7 1B1 5 1B2 4 1B3 3 1B4 2A 10 9 2B1 11 2B2 12 2B3 13 2B4 14 S0 S1 2 1 1OE 15 2OE absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V Continuous channel current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 mA Input clamp current, IK (VI/O < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –50 mA Package thermal impedance, θJA (see Note 2): D package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113°C/W DB package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131°C/W DBQ package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139°C/W DGV package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180°C/W PW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149°C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed. 2. The package thermal impedance is calculated in accordance with JESD 51. 2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 SN74CBT3253 DUAL 1-OF-4 FET MULTIPLEXER/DEMULTIPLEXER SCDS018I – MAY 1995 – REVISED MAY 1998 recommended operating conditions (see Note 3) MIN MAX VCC VIH Supply voltage 4 5.5 High-level control input voltage 2 VIL TA Low-level control input voltage Operating free-air temperature –40 UNIT V V 0.8 V 85 °C NOTE 3: All unused control inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER VIK II TEST CONDITIONS VCC = 4.5 V, VCC = 5 V, II = –18 mA VI = 5.5 V or GND IO = 0, One input at 3.4 V, ICC ∆ICC‡ Control inputs VCC = 5.5 V, VCC = 5.5 V, Ci Control inputs VI = 3 V or 0 Cio(OFF) i (OFF) A port B port MIN TYP† VI = VCC or GND Other inputs at VCC or GND MAX –1.2 V ±1 µA 3 µA 2.5 mA 3.5 pF 10 VO = 3 V or 0 0, OE = VCC VCC = 4 V, TYP at VCC = 4 V VI = 2.4 V, II = 15 mA VI = 0 II = 64 mA II = 30 mA ron§ VCC = 4.5 V UNIT pF 4 5 7 5 7 Ω VI = 2.4 V, II = 15 mA 10 15 † All typical values are at VCC = 5 V (unless otherwise noted), TA = 25°C. ‡ This is the increase in supply current for each input that is at the specified TTL voltage level rather than VCC or GND. § Measured by the voltage drop between the A and the B terminals at the indicated current through the switch. On-state resistance is determined by the lower voltage of the two (A or B) terminals. switching characteristics over recommended operating free-air temperature range, CL = 50 pF (unless otherwise noted) (see Figure 1) VCC = 4 V VCC = 5 V ± 0.5 V MIN MIN FROM (INPUT) TO (OUTPUT) tpd¶ A or B B or A 0.35 0.25 ns tpd S A or B 6.6 1.6 6.2 ns 7.1 1.3 6.3 7.3 1.4 6.4 7.9 1.1 7.4 7.3 2.3 7 PARAMETER ten S A or B OE S tdi dis MAX UNIT MAX A or B OE ns ns ¶ The propagation delay is the calculated RC time constant of the typical on-state resistance of the switch and the specified load capacitance, when driven by an ideal voltage source (zero output impedance). POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 SN74CBT3253 DUAL 1-OF-4 FET MULTIPLEXER/DEMULTIPLEXER SCDS018I – MAY 1995 – REVISED MAY 1998 PARAMETER MEASUREMENT INFORMATION 7V 500 Ω From Output Under Test S1 Open GND CL = 50 pF (see Note A) TEST S1 tpd tPLZ/tPZL tPHZ/tPZH Open 7V Open 500 Ω 3V Output Control (low-level enabling) LOAD CIRCUIT 1.5 V 0V tPZL 3V Input 1.5 V 1.5 V 0V tPLH Output Waveform 1 S1 at 7 V (see Note B) 1.5 V tPLZ 3.5 V 1.5 V VOL + 0.3 V VOL tPZH tPHL VOH Output 1.5 V 1.5 V VOL Output Waveform 2 S1 at Open (see Note B) VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES tPHZ 1.5 V VOH VOH – 0.3 V 0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 ns. D. The outputs are measured one at a time with one transition per measurement. E. tPLZ and tPHZ are the same as tdis. F. tPZL and tPZH are the same as ten. G. tPLH and tPHL are the same as tpd. Figure 1. Load Circuit and Voltage Waveforms 4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER’S RISK. In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI’s publication of information regarding any third party’s products or services does not constitute TI’s approval, warranty or endorsement thereof. Copyright 1998, Texas Instruments Incorporated