Multi-Rate CWDM SFP Transceiver SPC-MR-EIR-xx Features • Single 3.3 V supply • 30/60 km reach (1270~1450nm/1470~1610nm) • 20dB minnimum, 24 dB typical link budget • Commercial temperature available • CWDM wavelength, DFB laser • SFP MSA SFF-8074i compliant • GR 253/STM G.957 compliant • Digital Diagnostic SFF-8472 Rev.9.3 compliant • Telcordia GR-468 compliant • RoHS compliant General Operating Parameter Symbol Min. Typical Max. Unit Supply Voltage Vcc 3.135 3.3 3.465 V Total Current Icc - - 300 mA Power Supply Noise Rejectiona PSR 100 - - mVp-p Operating Temperature (-Cxx) Top -5 - 70 ºC Storage Temperature Tst -40 - 85 ºC Data Rate DR 100 - 2700 Mbps Max Unit a) 20Hz to 155MHz Transmitter Specifications (Optical) Parameter Symbol Min Typical Optical Power Pop 0 2 5 dBm Average Launch Power Of Off Tx Poff - - -45 dBm Extinction Ratio ER 9 - - dB Jgen - - 0.007 UI Optical Rise Timeb tr - - 160 ps Optical Fall Timeb tf - 160 ps Mean Wavelength λ 1xxx-6.5nm 1xxx 1xxx+6.5nm nm nm Eye Mask Optical Jitter Generation IEEE 802.3Z, SONET/SDH compliant Spectral Width (20dB) ∆λ - - 1 Dispersion Penalty (60 Km)c dp - 0.5 1 dB Relative Intensity Noise RIN - - -120 dB/Hz Reflection Toleranced rp -24 - - dB b) 20%-80% values c) Measured at BER of 1e-12, PRBS of 223-1, at eye center d) 1 dB degradation of receiver sensitivity LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 1 LUMNDS1538-Aug0407 Rev A.3 Multi-Rate CWDM SFP Transceiver SPC-MR-EIR-xx Transmitter Specifications (Electical) Parameter Symbol Min Typical Max Unit Rin 80 100 120 Ω PECL Single Ended Data Input Swing Vin,p-p 250 - 1200 mV TxFault_Fault Vfault 2 - Vcc V Vnormal Vee - Vee+0.5 V Vd 2 - Vcc V Ven Vee - Vee+0.8 V Symbol Min Typical Max Unit Rsens,low - -22 -20 dBm Input Differential Impedence TxFault_Normal TxDisable_Disable TxDisable_Enable Receiver Specifications Parameter Receive Power Lowe Receive Power Highe Damage Threshold For Receiver Wavelength Maximum Reflectance Of Receiver Rsens,high 0 - - dBm Pin,damage 5 - - dBm λ 1200 - 1625 nm RX_r - - -27 dB -30 - - dBm LOS De-assert - - -20 dBm LOS Hysteresis 0.5 - - dB LOS Assert e) 10-10 BER, PRBS 223-1 for SONE T, 10-12 BER, PRBS 27-1 for Gigabit Ethernet Electrical Output Parameter Symbol Min Typical Max Unit PECL Single Ended Data Output Swing Vout, p-p 185 - 800 mV Data Output Rise Time tr - - 175 ps Data Output Fall Time tf - - 175 ps Timing and Electrical Parameter Symbol Min Typical Max Unit t_on - - 1 ms Tx Disable Assert Time t_off - - 10 µs Time To Initialize, Including Reset Of Tx Fault t_init - - 300 ms Tx Disable Negate Time Tx Fault Assert Time t_fault - - 100 µs Tx Disable To Reset t_reset 10 - - µs t_loss_on - - 100 µs LOS De-assert Time t_loss_off - - 100 µs Serial ID Clock Rate f_serial_clock - - 100 KHz 2 - - V LOS Assert Time RX_LOS Voltage (High) RX_LOS Voltage (Low) LOS Output Voltage-Fault LOS Output Voltage-Normal - - 0.8 V VLOS fault 2 - Vcc V VLOSnormal Vee - Vee+0.5 V MOD_DEF (0:2)-High VH 2 - Vcc V MOD_DEF (0:2)-Low VL Vee - Vee+0.5 V LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 2 LUMNDS1538-Aug0407 Rev A.3 Multi-Rate CWDM SFP Transceiver SPC-MR-EIR-xx λ Wavelength Ordering SPC-MR-EIR-xxCDA See table below for “XX” values λc Wavelength Guide Code λC Unit Code λC Unit Code λC Unit Code λC Unit 31 1310 nm 39 1390 nm 47 1470 nm 55 1550 nm 33 1330 nm 41 1410 nm 49 1490 nm 57 1570 nm 35 1350 nm 43 1430 nm 51 1510 nm 59 1590 nm 37 1370 nm 45 1450 nm 53 1530 nm 61 1610 nm Range Diagnostics Accuracy Unit Calibration Temperature (-CDA) -5 to 70 ±3 ºC External Tc(C) = Tslope*Tad(16 bit signed twos complement value) + Toffset Voltage 0 to Vcc 0.1 V External V(Volts) = Vslope*Vad (16 bit unsigned integer) + Voffset Bias Current 0 to 120 5 mA External I(mA)=Islope*Iad(16 bit unsigned integer)+Ioffset Parameter Formula TX Power 0 to 5 ±3 dB dBm External TX_PWR(µW)=TX_PWRslope*TX_PWRad(16 bit unsigned integer +TX_ PWRoffset RX Power -20 to 0 ±3 dB dBm External RX_PWR(µW)=A0+A1*x+A2*x^2+A3*x^3+A4*x^4 LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 3 LUMNDS1538-Aug0407 Rev A.3 Multi-Rate CWDM SFP Transceiver SPC-MR-EIR-xx EEPROM Serial ID Name of Field Vendor Name Vendor OUI Vendor PN LUMINENTOIC.COM Description of Field SFP Vendor Name(ASCII) IEEE Vendor OUI Code For LuminentOIC Inc. Part Number in ASCII, e.g. SPC-MR-EIR-xxCDA Address Hex ASCII 20 4C L 21 55 U 22 4D M 23 49 I 24 4E N 25 45 E 26 4E N 27 54 T 28 4F O 29 49 I 30 43 C 37 00 38 06 39 B5 40 53 41 50 P 42 43 C 43 4D M 44 52 R 45 45 E 46 49 I 47 52 R 48 x x 49 x x 50 43 C 51 44 D 52 41 A 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 4 S LUMNDS1538-Aug0407 Rev A.3 Multi-Rate CWDM SFP Transceiver SPC-MR-EIR-xx Pin Function Notes 1 VeeT TX GND 2 TX_FAULT Open Collector 3 TX_DISABLE Internally Pulled High 4 MOD_DEF2 Serial Data Input 5 MOD_DEF1 Serial Clock Input 6 MOD_DEF0 Internally Grounded 7 NC Not Connected 8 LOS Open Collector 9 VeeR RX Ground 10 VeeR RX Ground 11 VeeR RX Ground 12 RXD- RX Data Negative 13 RXD+ RX Data Positive 14 VeeR RX GND 15 VccR RX Power 16 VccT TX Power 17 VeeT TX GND 18 TXD+ TX Data Positive 19 TXD- TX Data Negative 20 VeeT TX GND LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 5 LUMNDS1538-Aug0407 Rev A.3 Multi-Rate CWDM SFP Transceiver SPC-MR-EIR-xx Outline Drawing Units in mm(inches) LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 6 LUMNDS1538-Aug0407 Rev A.3 Multi-Rate CWDM SFP Transceiver SPC-MR-EIR-xx Suggested Transceiver Interface 1�H Vcc 10�F 1�H 0.1�F VCCT .01�F Protocol IC R1 LuminentOIC SFP 10K� TX_DISABLE TX_DISABLE TX_FAULT TX_FAULT TD + SerDes Laser Driver .01�F 100� TD VEET .01�F VCCR 10�F 0.1�F RD + Receiver Amplifier .01�F 100� RD - RX_LOS RX_LOS Vcc R VEER 1 R1 R1 .01�F EEPROM R1 MOD_DEF 2 MOD_DEF 1 MOD_DEF 0 R1=4.7K to 10K� LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 7 LUMNDS1538-Aug0407 Rev A.3 Multi-Rate CWDM SFP Transceiver SPC-MR-EIR-xx Ordering Information Available Options: SPC-MR-EIR-xxCDA SPC-MR-EIR-xxCNA Part numbering Definition: SPC - MR - EIR - xx Temperature Diagnostic Revision • SPC = Small Form Pluggable CWDM MR = Multi Rate EIR = IEEE 802.3ah Interface 30/60 km • xx = CWDM Wavelength • Operating Temperature C = Commercial temperature (-5 to 70ºC) • D = Digital Diagnostic (SFF-8472) N = No Digital Diagnostic • Design Revision A = RoHS compliant Warnings: Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow guidelines according to proper ESD procedures. Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation. Legal Notes: IMPORTANT NOTICE! All information contained in this document is subject to change without notice, at LuminentOIC’s sole and absolute discretion. LuminentOIC warrants performance of its products to current specifications only in accordance with the company’s standard one-year warranty; however, specifications designated as “preliminary” are given to describe components only, and LuminentOIC expressly disclaims any and all warranties for said products, including express, implied, and statutory warranties, warranties of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of Sale for further warranty information. LuminentOIC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and LuminentOIC makes no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this document are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. LuminentOIC customers using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify LuminentOIC for any damages resulting from such use or sale. THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that LuminentOIC is not liable for any actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact LuminentOIC to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current. © LuminentOIC, Inc. 2003 All rights reserved LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 8 LUMNDS1538-Aug0407 Rev A.3