TAS5614A www.ti.com SLAS712 – JUNE 2010 150W STEREO / 300W MONO PurePath™ HD DIGITAL-INPUT POWER STAGE Check for Samples: TAS5614A FEATURES APPLICATIONS • • • • • • 23 • • • • • • • • PurePath™ HD Enabled Integrated Feedback Provides: – Signal Bandwidth up to 80kHz for High Frequency Content From HD Sources – Ultralow 0.03% THD at 1W into 4Ω – Ultralow 0.01% THD at 1W into 8Ω – Flat THD at all Frequencies for Natural Sound – 80dB PSRR (BTL, No Input Signal) – >100dB (A weighted) SNR – Click and Pop Free Startup Pin compatible with TAS5631, TAS5616 and TAS5612 Multiple Configurations Possible on the Same PCB With Stuffing Options: – Mono Parallel Bridge Tied Load (PBTL) – Stereo Bridge Tied Load (BTL) – 2.1 Single Ended Stereo Pair and Bridge Tied Load Subwoofer Total Output Power at 10%THD+N – 300W in Mono PBTL Configuration – 150W per Channel in Stereo BTL Configuration Total Output Power in BTL Configuration at 1%THD+N – 160W Stereo into 3Ω – 125W Stereo into 4Ω – 85W Stereo into 6Ω – 65W Stereo into 8Ω >90% Efficient Power Stage With 60-mΩ Output MOSFETs Self-Protection Design (Including Undervoltage, Overtemperature, Clipping, and Short-Circuit Protection) With Error Reporting EMI Compliant When Used With Recommended System Design Two Thermally Enhanced Package Options: – PHD (64-Pin QFP) – DKD (44-Pin PSOP3) Home Theater Systems AV Receivers DVD/Blu-ray™ Receivers Mini Combo Systems Active Speakers and Subwoofers DESCRIPTION The TAS5614A is a high performance analog input Class D amplifier with integrated closed loop feedback technology (known as PurePath™ HD) with the ability to drive up to 150W (1) Stereo into 4 to 8 Ω Speakers from a single 36V supply. PurePath™ HD technology enables traditional AB-Amplifier performance (<0.03% THD) levels while providing the power efficiency of traditional class D amplifiers. Unlike traditional Class D amplifiers, the distortion curve only increases once the output levels move into clipping. PurePath™ HD Power PAD™ PurePath™ HD technology enables lower idle losses making the device even more efficient. TOTAL HARMONIC DISTORTION+NOISE VS OUTPUT POWER 10 4Ohm (6kHz) THD+N - Total tal Harmonic Distortion - % 1 4Ohm (1kHz) 1 0,1 0,01 TC = 75 C CONFIG = BTL 0,001 0,01 1 100 PO - Output Power - W (1) Achievable output power levels are dependent on the thermal configuration of the target application. A high performance thermal interface material between the package exposed heatslug and the heat sink should be used to achieve high output power levels. 1 2 3 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PurePath, Power PAD are trademarks of Texas Instruments. All other trademarks are the property of their respective owners. UNLESS OTHERWISE NOTED this document contains PRODUCTION DATA information current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2010, Texas Instruments Incorporated TAS5614A SLAS712 – JUNE 2010 www.ti.com These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. DEVICE INFORMATION Terminal Assignment Both package types contains a heat slug that is located on the top side of the device for convenient thermal coupling to the heat sink. DKD PACKAGE (TOP VIEW) PR EV IE W 44 pins PACKAGE (TOP VIEW) CT AGND VREG INPUT_C INPUT_D TEST NC NC SD OTW READY M1 M2 M3 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 OD U GND_A GND_B GND_B OUT_B OUT_B PVDD_B PVDD_B BST_B BST_C PVDD_C PVDD_C OUT_C OUT_C GND_C GND_C _ GND_D PSU_REF VDD OC_ADJ RESET C_STARTUP INPUT_A INPUT_B VI_CM GND PR 64-pins QFP package 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 OTW2 CLIP READY M1 M2 M3 GND GND GVDD_C GVDD_D BST_D OUT_D OUT_D PVDD_D PVDD_D GND_D OC_ADJ RESET C_STARTUP INPUT_A INPUT_B VI_CM GND AGND VREG INPUT_C INPUT_D TEST NC NC SD OTW1 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 VDD PSU_REF NC NC NC NC GND GND GVDD_B GVDD_A BST_A OUT_A OUT_A PVDD_A PVDD_A GND_A PHD PACKAGE (TOP VIEW) 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 GVDD_AB BST_A PVDD_A PVDD_A OUT_A OUT_A GND_A GND_B OUT_B PVDD_B BST_B BST_C PVDD_C OUT_C GND_C GND_D OUT_D OUT_D PVDD_D PVDD_D BST_D GVDD_CD PIN ONE LOCATION PHD PACKAGE Electrical Pin 1 Pin 1 Marker White Dot 2 Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TAS5614A TAS5614A www.ti.com SLAS712 – JUNE 2010 MODE SELECTION PINS MODE PINS PWM INPUT (1) OUTPUT CONFIGURATION 0 2N 2 × BTL AD mode 1 — — Reserved 1 0 2N 2 × BTL BD mode 0 1 1 1N 1 × BTL +2 ×SE AD mode 1 0 0 1N 4 × SE AD mode 2N 1N M3 M2 M1 0 0 0 0 0 (1) (2) 1 0 1 1 1 0 1 1 1 1 × PBTL DESCRIPTION INPUT_C (2) INPUT_D (2) 0 0 AD mode 1 0 BD mode Reserved The 1N and 2N naming convention is used to indicate the number of PWM lines to the power stage per channel in a specific mode. INPUT_C and D are used to select between a subset of AD and BD mode operations in PBTL mode PACKAGE HEAT DISSIPATION RATINGS (1) PARAMETER TAS5614APHD TAS5614ADKD RqJC (°C/W) – 2 BTL or 4 SE channels 3.2 2.1 RqJC (°C/W) – 1 BTL or 2 SE channel(s) 5.4 3.5 RqJC (°C/W) – 1 SE channel Pad Area (1) (2) (2) 7.9 5.1 64mm2 80mm2 JC is junction-to-case, CH is case-to-heat sink RqCH is an important consideration. Assume a 2-mil thickness of thermal grease with a thermal conductivity of 2.5 W/mK between the pad area and the heat sink and both channels active. The RqCH with this condition is 1.1°C/W for the PHD package and 0.44°C/W for the DKD package. Table 1. ORDERING INFORMATION (1) (1) TA PACKAGE DESCRIPTION 0°C–70°C TAS5614APHD 64 pin HTQFP 0°C–70°C TAS5614ADKD 44 pin PSOP3 For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI website at www.ti.com. Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TAS5614A 3 TAS5614A SLAS712 – JUNE 2010 www.ti.com ABSOLUTE MAXIMUM RATINGS over operating free-air temperature range unless otherwise noted (1) TAS5614A UNIT VDD to GND –0.3 to 13.2 V GVDD to GND –0.3 to 13.2 V –0.3 to 53 V PVDD_X to GND_X (2) OUT_X to GND_X (2) –0.3 to 53 V –0.3 to 66.2 V BST_X to GVDD_X (2) –0.3 to 53 V VREG to GND –0.3 to 4.2 V GND_X to GND –0.3 to 0.3 V GND to AGND –0.3 to 0.3 V OC_ADJ, M1, M2, M3, OSC_IO+, OSC_IO-, FREQ_ADJ, VI_CM, C_STARTUP, PSU_REF to GND –0.3 to 4.2 V INPUT_X –0.3 to 7 V RESET, SD, OTW1, OTW2, CLIP, READY to GND –0.3 to 7 V BST_X to GND_X (2) Maximum continuous sink current (SD, OTW1, OTW2, CLIP, READY) Maximum operating junction temperature range, TJ Storage temperature, Tstg Electrostatic discharge (1) (2) (3) Human body model (3) 9 mA 0 to 150 °C –40 to 150 °C ±2 kV ±500 V (all pins) Charged device model (3) (all pins) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. These voltages represents the DC voltage + peak AC waveform measured at the terminal of the device in all conditions. Failure to follow good anti-static ESD handling during manufacture and rework will contribute to device malfunction. Make sure the operators handling the device are adequately grounded through the use of ground straps or alternative ESD protection. RECOMMENDED OPERATING CONDITIONS over operating free-air temperature range (unless otherwise noted) MIN NOM MAX UNIT PVDD_x Half-bridge supply DC supply voltage 18 36 38 V GVDD_x Supply for logic regulators and gate-drive circuitry DC supply voltage 10.8 12 13.2 V VDD Digital regulator supply voltage DC supply voltage 10.8 12 13.2 V 3.5 4 2.8 3 1.6 2 2.8 3 7 10 7 15 7 10 352 384 RL(BTL) RL(SE) Output filter according to schematics in the application information section. Load impedance RL(PBTL) RL(BTL) Output filter according to schematics in the application information section. ROC = 22kΩ, add Schottky diodes from OUT_X to GND_X. Load impedance LOUTPUT(BTL) LOUTPUT(SE) Output filter inductance Minimum output inductance at IOC LOUTPUT(PBTL) Ω Ω mH FPWM PWM frame rate CPVDD PVDD close decoupling capacitors 2 mF ROC Over-current programming resistor Resistor tolerance = 5% 22 30 kΩ ROC_LATCHED Over-current programming resistor Resistor tolerance = 5% 47 64 TJ Junction temperature 4 0 Submit Documentation Feedback 500 kHz kΩ 150 °C Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TAS5614A TAS5614A www.ti.com SLAS712 – JUNE 2010 PIN FUNCTIONS PIN FUNCTION (1) DESCRIPTION NAME PHD NO. DKD NO. AGND 8 10 P Analog ground BST_A 54 43 P HS bootstrap supply (BST), external 0.033mF capacitor to OUT_A required. BST_B 41 34 P HS bootstrap supply (BST), external 0.033mF capacitor to OUT_B required. BST_C 40 33 P HS bootstrap supply (BST), external 0.033mF capacitor to OUT_C required. BST_D 27 24 P HS bootstrap supply (BST), external 0.033mF capacitor to OUT_D required. CLIP 18 — O Clipping warning; open drain; active low C_STARTUP 3 5 O Startup ramp requires a charging capacitor of 4.7nF to GND TEST 12 14 I Connect to VREG node GND 7, 23, 24, 57, 58 9 P Ground GND_A 48, 49 38 P Power ground for half-bridge A GND_B 46, 47 37 P Power ground for half-bridge B GND_C 34, 35 30 P Power ground for half-bridge C GND_D 32, 33 29 P Power ground for half-bridge D GVDD_A 55 — P Gate drive voltage supply requires 0.1mF capacitor to GND GVDD_B 56 — P Gate drive voltage supply requires 0.1mF capacitor to GND GVDD_C 25 — P Gate drive voltage supply requires 0.1mF capacitor to GND GVDD_D 26 — P Gate drive voltage supply requires 0.1mF capacitor to GND GVDD_AB — 44 P Gate drive voltage supply requires 0.22mF capacitor to GND GVDD_CD — 23 P Gate drive voltage supply requires 0.22mF capacitor to GND INPUT_A 4 6 I Input signal for half bridge A INPUT_B 5 7 I Input signal for half bridge B INPUT_C 10 12 I Input signal for half bridge C INPUT_D 11 13 I Input signal for half bridge D M1 20 20 I Mode selection M2 21 21 I Mode selection M3 22 22 I Mode selection NC 59–62 – — No connect, pins may be grounded. NC 13, 14 15, 16 — No connect, pins may be grounded. OC_ADJ 1 3 O Analog overcurrent programming pin requires resistor to ground. OTW — 18 O Overtemperature warning signal, open drain, active low. OTW1 16 — O Overtemperature warning signal, open drain, active low. OTW2 17 — O Overtemperature warning signal, open drain, active low. OUT_A 52, 53 39, 40 O Output, half bridge A OUT_B 44, 45 36 O Output, half bridge B OUT_C 36, 37 31 O Output, half bridge C OUT_D 28, 29 27, 28 O Output, half bridge D 63 1 P PSU Reference requires close decoupling of 4.7mF to GND PVDD_A 50, 51 41, 42 P Power supply input for half bridges A requires close decoupling of 2mF capacitor to GND_A PVDD_B 42, 43 35 P Power supply input for half bridges B requires close decoupling of 2mF capacitor to GND_B PVDD_C 38, 39 32 P Power supply input for half bridges C requires close decoupling of 2mF capacitor to GND_C PVDD_D 30, 31 25, 26 P Power supply input for half bridges D requires close decoupling of 2mF capacitor to GND_D READY 19 19 O Normal operation; open drain; active high RESET 2 4 I Device reset Input; active low SD 15 17 O Shutdown signal, open drain, active low VDD 64 2 P Power supply for digital voltage regulator requires a 47mF capacitor in parallel with a 0.1mF capacitor to GND for decoupling. VI_CM 6 8 O Analog comparator reference node requires close decoupling of 4.7mF to GND PSU_REF (1) I = Input, O = Output, P = Power Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TAS5614A 5 TAS5614A SLAS712 – JUNE 2010 www.ti.com PIN FUNCTIONS (continued) PIN NAME PHD NO. DKD NO. VREG 9 11 FUNCTION (1) P DESCRIPTION Digital regulator supply filter pin requires 0.1mF capacitor to GND TYPICAL SYSTEM BLOCK DIAGRAM Caps for External Filtering and Startup/Stop System microcontroller (2) AMP RESET LeftChannel Output PWM_A C_STARTUP VI_CM /CLIP PSU_REF RESET VALID READY /SD *NOTE1 /OTW1, /OTW2, /OTW I2C TAS5518/ TAS5508/ TAS5086 BST_A BST_B OUT_A INPUT_A PWM_B Input H-Bridge 1 INPUT_B Output H-Bridge 1 2 OUT_B 2 Bootstrap Caps 2nd Order L-C Output Filter for each H-Bridge 2-CHANNEL H-BRIDGE BTL MODE PWM_C INPUT_C PWM_D OUT_C Input H-Bridge 2 INPUT_D Output H-Bridge 2 2 OUT_D 8 36V 50V PVDD 12V PVDD Power Supply Decoupling SYSTEM Power Supplies GND 8 BST_D OC_ADJ TEST VREG AGND M3 2nd Order L-C Output Filter for each H-Bridge BST_C VDD M2 GND M1 GND_A, B, C, D Hardwire Mode Control GVDD_A, B, C, D 2 PVDD_A, B, C, D RightChannel Output Bootstrap Caps 4 GVDD, VDD, and VREG Power Supply Decoupling Hardwire OverCurrent Limit GND GVDD (12V)/VDD (12V) VAC (1) 6 Logic AND is inside or outside the micro controller. Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TAS5614A TAS5614A www.ti.com SLAS712 – JUNE 2010 FUNCTIONAL BLOCK DIAGRAM CLIP READY OTW1 OTW2 SD PROTECTION & I/O LOGIC M1 M2 M3 RESET STARTUP CONTROL C_STARTUP VDD POWER-UP RESET UVP VREG VREG AGND TEMP SENSE GVDD_A GVDD_C GVDD_B OVER-LOAD PROTECTION CURRENT SENSE CB3C 4 PPSC 4 4 GND GVDD_D OC_ADJ PVDD_X OUT_X GND_X GVDD_A PWM ACTIVITY DETECTOR BST_A PVDD_A PWM RECEIVER CONTROL TIMING CONTROL GATE-DRIVE OUT_A GND_A PSU_REF GVDD_B VI_CM - ANALOG LOOP FILTER INPUT_A BST_B + PVDD_B INPUT_C INPUT_D PVDD_X GND ANALOG LOOP FILTER ANALOG LOOP FILTER + ANALOG COMPARATOR MUX 4 AGC ANALOG INPUT MUX INPUT_B PWM RECEIVER + ANALOG LOOP FILTER CONTROL TIMING CONTROL GATE-DRIVE OUT_B GND_B GVDD_C BST_C PVDD_C PWM RECEIVER CONTROL TIMING CONTROL GATE-DRIVE + OUT_C GND_C GVDD_D BST_D PVDD_D PWM RECEIVER CONTROL TIMING CONTROL GATE-DRIVE OUT_D GND_D Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TAS5614A 7 TAS5614A SLAS712 – JUNE 2010 www.ti.com AUDIO CHARACTERISTICS (BTL) Audio performance is recorded as a chipset consisting of a TAS5518 PWM Processor (modulation index limited to 97.7%) and a TAS5614A power stage. PCB and system configurations are in accordance with recommended guidelines. Audio frequency = 1kHz, PVDD_X = 36V, GVDD_X = 12V, RL = 4Ω, fS = 384 kHz, ROC = 30kΩ, TC = 75°C, Output Filter: LDEM = 7mH, CDEM = 680nF, MODE = 000, unless otherwise noted. PARAMETER PO Power output per channel TEST CONDITIONS MIN TYP MAX UNIT RL = 3Ω, 10% THD+N (ROC = 22kΩ, add Schottky diodes from OUT_X to GND_X.) 200 RL = 4Ω, 10% THD+N 150 RL = 3Ω, 1% THD+N (ROC = 22kΩ, add Schottky diodes from OUT_X to GND_X.) 160 RL = 4Ω, 1% THD+N 125 1 W, RL = 4Ω 0.03% 1 W, RL = 8Ω 0.01% W THD+N Total harmonic distortion + noise Vn Output integrated noise A-weighted, TAS5518 Modulator |VOS| Output offset voltage No signal SNR Signal-to-noise ratio (1) A-weighted, TAS5518 Modulator 103 dB DNR Dynamic range A-weighted, input level –60 dBFS using TAS5518 modulator 103 dB Pidle Power dissipation due to Idle losses (IPVDD_X) PO = 0, 4 channels switching (2) 2.6 W (1) (2) 8 125 20 mV 40 mV SNR is calculated relative to 1% THD-N output level. Actual system idle losses also are affected by core losses of output inductors. Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TAS5614A TAS5614A www.ti.com SLAS712 – JUNE 2010 AUDIO CHARACTERISTICS (PBTL) Audio performance is recorded as a chipset consisting of a TAS5518 PWM Processor (modulation index limited to 97.7%) and a TAS5614A power stage. PCB and system configurations are in accordance with recommended guidelines. Audio frequency = 1kHz, PVDD_X = 36V, GVDD_X = 12V, RL = 2Ω, fS = 384kHz, ROC = 30kΩ, TC = 75°C, Output Filter: LDEM = 7mH, CDEM = 1mF, MODE = 101-00, unless otherwise noted. PARAMETER PO TEST CONDITIONS Power output per channel MIN TYP MAX RL = 2Ω, 10%, THD+N 300 RL = 3Ω, 10%, THD+N 200 RL = 4Ω, 10%, THD+N 160 RL = 2Ω, 1% THD+N 250 RL = 3Ω, 1% THD+N 160 RL = 4Ω, 1% THD+N UNIT W 130 THD+N Total harmonic distortion + noise 1W Vn Output integrated noise A-weighted, TAS5518 Modulator 128 mV SNR Signal to noise ratio (1) A-weighted, TAS5518 Modulator 103 dB DNR Dynamic range A-weighted, input level –60 dBFS using TAS5518 modulator 103 dB Pidle Power dissipation due to idle losses (IPVDD_X) PO = 0, 4 channels switching (2) 2.4 W (1) (2) 0.03% SNR is calculated relative to 1% THD-N output level. Actual system idle losses are affected by core losses of output inductors. ELECTRICAL CHARACTERISTICS PVDD_X = 36V, GVDD_X = 12V, VDD = 12V, TC (Case temperature) = 75°C, fS = 384kHz, unless otherwise specified. PARAMETER TEST CONDITIONS MIN TYP MAX UNIT INTERNAL VOLTAGE REGULATOR AND CURRENT CONSUMPTION VREG Voltage regulator, only used as reference node, VREG VI_CM Analog comparator reference node, VI_CM IVDD VDD supply current IGVDD_x Gate-supply current per half-bridge IPVDD_x Half-bridge idle current VDD = 12V 3 3.3 3.6 V 1.5 1.75 1.9 V Operating, 50% duty cycle 20 Idle, reset mode 20 50% duty cycle 10 Reset mode 1.5 mA mA 50% duty cycle without output filter or load 16.8 mA Reset mode, No switching 620 mA OUTPUT-STAGE MOSFETs Drain-to-source resistance, low side (LS) RDS(on) Drain-to-source resistance, high side (HS) TJ = 25°C, excludes metallization resistance, GVDD = 12V 60 100 mΩ 60 100 mΩ Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TAS5614A 9 TAS5614A SLAS712 – JUNE 2010 www.ti.com ELECTRICAL CHARACTERISTICS (continued) PVDD_X = 36V, GVDD_X = 12V, VDD = 12V, TC (Case temperature) = 75°C, fS = 384kHz, unless otherwise specified. PARAMETER TEST CONDITIONS MIN TYP MAX UNIT I/O PROTECTION Vuvp,G Undervoltage protection limit, GVDD_x Vuvp,hyst (1) 10 V 0.6 V (1) Overtemperature warning 1 95 100 105 °C OTW2 (1) Overtemperature warning 2 115 125 135 °C OTWhyst Temperature drop needed below OTW temperature for OTW to be inactive after OTW event. OTW1 (1) 25 Overtemperature error OTE (1) OTEHYST (1) OLPC 145 °C 30 °C A reset needs to occur for SD to be released following an OTE event 25 °C fPWM = 384kHz 2.6 ms Resistor – programmable, nominal peak current in 1Ω load, ROCP = 30kΩ 14 Resistor – programmable, nominal peak current in 1Ω load, ROCP = 22kΩ (With Schottky diodes from OUT_X to GND_X.) 18 Resistor – programmable, nominal peak current in 1Ω load, ROCP = 64kΩ 14 Resistor – programmable, nominal peak current in 1Ω load, ROCP = 47kΩ (With Schottky diodes from OUT_X to GND_X.) 18 Overcurrent limit protection IOC_LATCHED 165 OTE-OTW differential Overload protection counter IOC 155 °C Overcurrent limit protection A A IOCT Overcurrent response time Time from application of short condition to Hi-Z of affected half bridge 150 ns IPD Internal pulldown resistor at output of each half bridge Connected when RESET is active to provide bootstrap charge. Not used in SE mode. 3 mA STATIC DIGITAL SPECIFICATIONS VIH High level input voltage VIL Low level input voltage Ilkg Input leakage current INPUT_X, M1, M2, M3, RESET 1.9 V 0.8 V 100 mA kΩ OTW/SHUTDOWN (SD) RINT_PU Internal pullup resistance, OTW1 to VREG, OTW2 to VREG, SD to VREG VOH High level output voltage VOL Low level output voltage IO = 4mA FANOUT Device fanout OTW1, OTW2, SD, CLIP, READY No external pullup (1) 10 Internal pullup resistor External pullup of 4.7kΩ to 5V 20 26 33 3 3.3 3.6 4.5 5 200 30 500 V mV devices Specified by design. Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TAS5614A TAS5614A www.ti.com SLAS712 – JUNE 2010 TYPICAL CHARACTERISTICS, BTL CONFIGURATION TOTAL HARMONIC+NOISE vs OUTPUT POWER OUTPUT POWER vs SUPPLY VOLTAGE 250 TC = 75°C TC = 75°C THD+N 10% 3W 4W 200 6W 1 PO - Output Power - W THD+N - Total Harmonic Distortion + Noise - % 10 8W 0.1 3W 4W 6W 150 8W 100 0.01 50 0.001 0.01 0.1 1 100 10 PO - Output Power - W 0 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 PVDD - Supply Voltage - V 1000 Figure 1. Figure 2. UNCLIPPED OUTPUT POWER vs SUPPLY VOLTAGE SYSTEM EFFICIENCY vs OUTPUT POWER 100 200 TC = 75°C 90 80 150 6W 4W 70 4W Efficiency - % PO - Output Power - W 8W 3W 6W 8W 100 60 50 40 30 50 20 TC = 25°C THD+N = 10% 10 0 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 PVDD - Supply Voltage - V 0 0 50 Figure 3. 100 150 200 250 300 350 2 Channel Output Power - W 400 Figure 4. Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TAS5614A 11 TAS5614A SLAS712 – JUNE 2010 www.ti.com TYPICAL CHARACTERISTICS, BTL CONFIGURATION (continued) SYSTEMS POWER LOSS vs OUTPUT POWER OUTPUT POWER vs CASE TEMPERATURE 30 250 TC = 25°C THD+N = 10% THD+N = 10% 3W 4W 200 PO - Output Power - W Powr Loss - W 4W 20 6W 10 0 50 100 150 200 250 300 350 2 Channel Output Power - W 100 8W 0 20 400 30 40 50 60 70 80 TC - Case Temperature - °C 90 Figure 5. Figure 6. NOISE AMPLITUDE vs FREQUENCY TOTAL HORMONIC DISTORTION+NOISE vs FREQUENCY 0 100 10 -40 THD+N - Total Harmonic Distortion - % TC = 75°C, REF = 25.46 V, Sample Rate = 48 kHz, FFT Size = 16384 -20 Noise Amplitude - dB 6W 50 8W 0 150 -60 -80 -100 -120 4W -140 RL = 4 W, TC = 75°C, Toroidal Output Inductors 1 0.1 1W 0.01 21 W (1/8 Power) -160 0 5 10 15 f - Frequency - kHz 20 0.001 10 Figure 7. 12 100 1k 10k f - Frequency - Hz 100k Figure 8. Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TAS5614A TAS5614A www.ti.com SLAS712 – JUNE 2010 TYPICAL CHARACTERISTICS, PBTL CONFIGURATION TOTAL HARMONIC+NOISE vs OUTPUT POWER OUTPUT POWER vs SUPPLY VOLTAGE 400 TC = 75°C 2W 350 3W 1 300 6W 8W 0.1 3W 4W 250 6W 200 8W 150 100 0.01 0.001 0.01 TC = 75°C THD+N = 10% 2W 4W PO - Output Power - W THD+N - Total Harmonic Distortion + Noise - % 10 50 0.1 1 100 10 PO - Output Power - W 0 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 PVDD - Supply Voltage - V 1000 Figure 9. Figure 10. OUTPUT POWER vs CASE TEMPERATURE 400 THD+N = 10% 2W 350 PO - Output Power - W 300 3W 250 4W 200 6W 150 100 8W 50 0 20 30 40 50 60 70 80 90 TC - Case Temperature - °C Figure 11. 100 Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TAS5614A 13 TAS5614A SLAS712 – JUNE 2010 www.ti.com APPLICATION INFORMATION PCB MATERIAL RECOMMENDATION FR-4 Glass Epoxy material with 2oz. (70mm) is recommended for use with the TAS5614A. The use of this material can provide for higher power output, improved thermal performance, and better EMI margin (due to lower PCB trace inductance. PVDD CAPACITOR RECOMMENDATION The large capacitors used in conjunction with each full-bridge, are referred to as the PVDD Capacitors. These capacitors should be selected for proper voltage margin and adequate capacitance to support the power requirements. In practice, with a well designed system power supply, 1000mF, 50V support more applications. The PVDD capacitors should be low ESR type because they are used in a circuit associated with high-speed switching. DECOUPLING CAPACITOR RECOMMENDATION To design an amplifier that has robust performance, passes regulatory requirements, and exhibits good audio performance, good quality decoupling capacitors should be used. In practice, X7R should be used in this application. The voltage of the decoupling capacitors should be selected in accordance with good design practices. Temperature, ripple current, and voltage overshoot must be considered. This fact is particularly true in the selection of the 0.1mF that is placed on the power supply to each half-bridge. It must withstand the voltage overshoot of the PWM switching, the heat generated by the amplifier during high power output, and the ripple current created by high power output. A minimum voltage rating of 50V is required for use with a 36V power supply. SYSTEM DESIGN RECOMMENDATIONS The following schematics and PCB layouts illustrate best practices in the use of the TAS5614A. 14 Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TAS5614A R_RIGHT_N IN_RIGHT_P IN_LEFT_N IN_LEFT_P /RESET 100R R13 100R R12 100R R11 100R R10 100R Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TAS5614A GND READY /CLIP /OTW2 /OTW1 /SD C18 100pF GND R19 47k GND GND GND GND 100nF C22 VREG GND VREG 4.7uF C21 4.7nF 30k C20 R20 4.7uF /OTW1 /SD NC NC TEST INPUT_D INPUT_C VREG AGND GND VI_CM INPUT_B INPUT_A C_STARTUP /RESET OC_ADJ PSU_REF /CLIP R18 VREG NC READY GND NC M1 U10 TAS5614APHD VREG NC M2 VDD /OTW2 GND GND GND C33 100nF GND GND GND GND GND NC M3 C31 100nF GVDD_B C32 100nF GND GND GVDD_C C30 100nF 3.3R 3.3R R33 R32 C43 33nF BST_A BST_D 3.3R GVDD_A GVDD_D C26 100nF OUT_A OUT_D C23 C25 10uF OUT_A OUT_D C40 33nF C60 2uF C63 2uF PVDD_A PVDD_D R31 PVDD_A PVDD_D 3.3R GND_A GND_D R30 GND_D GND_C GND_C OUT_C OUT_C PVDD_C PVDD_C BST_C BST_B PVDD_B PVDD_B OUT_B OUT_B GND_B GND_B GND_A GND GND C62 2uF C61 2uF GND L13 7uH 7uH L12 C42 33nF C41 33nF L11 7uH L10 7uH 1000uF C65 C53 680nF C52 680nF GND C51 680nF C50 680nF C72 1nF GND C73 1nF GND 1000uF C66 C71 1nF GND C70 1nF R73 3.3R C77 10nF C76 10nF R72 3.3R GND GND GND C68 47uF 63V R71 3.3R C75 10nF C74 10nF R70 3.3R C67 1000uF GND GND C69 2.2uF GND C64 1000uF GND GND PVDD GVDD/VDD (+12V) PVDD OUT_RIGHT_R - + GND OUT_RIGHT_P C78 10nF R74 3.3R OUT_LEFT_M - + OUT_LEFT_P PVDD GVDD/VDD (+12V) TAS5614A www.ti.com SLAS712 – JUNE 2010 Figure 12. Typical Differential (2N) BTL Application With BD Modulation Filters Submit Documentation Feedback 15 READY /CLIP /OTW2 /OTW1 /SD IN_N IN_P /RESET 100R 100R 100R GND 100pF GND VREG 47k VREG GND GND GND GND 100nF 4.7uF 4.7nF 30k VREG VREG GND GND 1 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 /OTW1 /SD NC NC TEST INPUT_D INPUT_C VREG AGND GND VI_CM INPUT_B INPUT_A C_STARTUP /RESET OC_ADJ 4.7uF GND GND 100nF 100nF GND GND GND GND 100nF GND 100nF GND GND 100nF TAS5614APHD VREG 33nF 3.3R 3.3R 3.3R 33nF GND 24 59 NC M3 3.3R 25 64 VDD /OTW2 17 63 PSU_REF /CLIP 18 57 GND GVDD_C 58 GND GND 10uF 19 56 GVDD_B GVDD_D 26 53 BST_D 62 NC READY 55 GVDD_A 28 27 52 OUT_A OUT_D 61 NC M1 20 54 BST_A OUT_A OUT_D 29 51 PVDD_A PVDD_D 50 PVDD_A PVDD_D 30 60 NC M2 21 Product Folder Link(s): TAS5614A 22 Submit Documentation Feedback 23 49 GND_A GND_D 31 16 32 VDD (+12V) 2uF GND_D GND_C GND_C OUT_C OUT_C PVDD_C PVDD_C BST_C BST_B PVDD_B PVDD_B OUT_B OUT_B GND_B GND_B GND_A GND 2uF 48 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 GND 2uF 2uF GND 33nF 33nF 7uH 7uH 7uH 7uH 1uF 1000uF 1000uF GND 1uF 1000uF 1000uF GND GND 1nF 1nF GND GND 47uF GND 3.3R 10nF 10nF 3.3R GND + - GVDD (+12V) PVDD OUT_LEFT_M GND OUT_LEFT_P 10nF 3.3R GND 2.2uF PVDD GVDD (+12V) TAS5614A SLAS712 – JUNE 2010 www.ti.com Figure 13. Typical (2N) PBTL Application With BD Modulation Filters Copyright © 2010, Texas Instruments Incorporated Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TAS5614A READY /OTW /SD IN_RIGHT_N IN_RIGHT_P IN_LEFT_N IN_LEFT_P /RESET VDD (+12V) 100R 100R 100R 100R 100R GND 100pF VREG 47k GND GND GND GND GND 100nF 4.7uF 4.7nF 30k 4.7uF VREG 10uF GND GND GND VREG VREG GND 100nF 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 M3 M2 M1 READY /OTW /SD NC NC TEST INPUT_D INPUT_C VREG AGND GND VI_CM INPUT_B INPUT_A TAS5614ADKD C_STARTUP /RESET OC_ADJ VDD PSU_REF GVDD_CD BST_D PVDD_D PVDD_D OUT_D OUT_D GND_D GND_C OUT_C PVDD_C BST_C BST_B PVDD_B OUT_B GND_B GND_A OUT_A OUT_A PVDD_A PVDD_A BST_A GVDD_AB 100nF 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 GND 100nF 33nF 1.5R 33nF GND 100nF GND 33nF GND 33nF 100nF 1.5R 2uF 2uF 2uF 2uF GND 7uH 680nF GND GND 1000uF 680nF 7uH GND 1000uF 7uH 680nF GND 680nF 7uH 1nF 1nF GND 1000uF 47uF 1nF 1nF 1000uF GND 3.3R 10nF 10nF 3.3R GND GND + - OUT_RIGHT_M GND OUT_RIGHT_P 10nF 3.3R OUT_LEFT_M - + OUT_LEFT_P GND 2.2uF 3.3R 10nF 10nF 3.3R GND GVDD (+12V) PVDD PVDD PVDD GVDD (+12V) TAS5614A www.ti.com SLAS712 – JUNE 2010 Figure 14. Typical Differential Input BTL Application with BD Modulation Filters DKD Package Submit Documentation Feedback 17 TAS5614A SLAS712 – JUNE 2010 www.ti.com THEORY OF OPERATION POWER SUPPLIES To facilitate system design, the TAS5614A needs only a 12V supply in addition to the (typical) 36V power-stage supply. An internal voltage regulator provides suitable voltage levels for the digital and low-voltage analog circuitry. Additionally, all circuitry requiring a floating voltage supply, e.g., the high-side gate drive, is accommodated by built-in bootstrap circuitry requiring only an external capacitor for each half-bridge. To provide outstanding electrical and acoustical characteristics, the PWM signal path including gate drive and output stage is designed as identical, independent half-bridges. For this reason, each half-bridge has separate gate drive supply (GVDD_X), bootstrap pins (BST_X), and power-stage supply pins (PVDD_X). Furthermore, an additional pin (VDD) is provided as supply for all common circuits. Although supplied from the same 12 V source, it is highly recommended to separate GVDD_A, GVDD_B, GVDD_C, GVDD_D, and VDD on the printed-circuit board (PCB) by RC filters (see application diagram for details). These RC filters provide the recommended high-frequency isolation. Special attention should be paid to placing all decoupling capacitors as close to their associated pins as possible. In general, inductance between the power supply pins and decoupling capacitors must be avoided. (See reference board documentation for additional information.) For a properly functioning bootstrap circuit, a small ceramic capacitor must be connected from each bootstrap pin (BST_X) to the power-stage output pin (OUT_X). When the power-stage output is low, the bootstrap capacitor is charged through an internal diode connected between the gate-drive power-supply pin (GVDD_X) and the bootstrap pin. When the power-stage output is high, the bootstrap capacitor potential is shifted above the output potential and thus provides a suitable voltage supply for the high-side gate driver. In an application with PWM switching frequencies in the range from 300kHz to 4000kHz, it is recommended to use 33nF ceramic capacitors, size 0603 or 0805, for the bootstrap supply. These 33-nF capacitors ensure sufficient energy storage, even during minimal PWM duty cycles, to keep the high-side power stage FET (LDMOS) fully turned on during the remaining part of the PWM cycle. Special attention should be paid to the power-stage power supply; this includes component selection, PCB placement, and routing. As indicated, each half-bridge has independent power-stage supply pins (PVDD_X). For optimal electrical performance, EMI compliance, and system reliability, it is important that each PVDD_X pin is decoupled with a 2mF ceramic capacitor placed as close as possible to each supply pin. It is recommended to follow the PCB layout of the TAS5614A reference design. For additional information on recommended power supply and required components, see the application diagrams in this data sheet. The 12V supply should be from a low-noise, low-output-impedance voltage regulator. Likewise, the 36V power-stage supply is assumed to have low output impedance and low noise. The power-supply sequence is not critical as facilitated by the internal power-on-reset circuit. Moreover, the TAS5614A is fully protected against erroneous power-stage turn on due to parasitic gate charging. Thus, voltage-supply ramp rates (dV/dt) are non-critical within the specified range (see the Recommended Operating Conditions table of this data sheet). SYSTEM POWER-UP/POWER-DOWN SEQUENCE Powering Up The TAS5614A does not require a power-up sequence. The outputs of the H-bridges remain in a high-impedance state until the gate-drive supply voltage (GVDD_X) and VDD voltage are above the undervoltage protection (UVP) voltage threshold (see the Electrical Characteristics table of this data sheet). Although not specifically required, it is recommended to hold RESET in a low state while powering up the device. This allows an internal circuit to charge the external bootstrap capacitors by enabling a weak pulldown of the half-bridge output. Powering Down The TAS5614A does not require a power-down sequence. The device remains fully operational as long as the gate-drive supply (GVDD_X) voltage and VDD voltage are above the undervoltage protection (UVP) voltage threshold (see the Electrical Characteristics table of this data sheet). Although not specifically required, it is a good practice to hold RESET low during power down, thus preventing audible artifacts including pops or clicks. 18 Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TAS5614A TAS5614A www.ti.com SLAS712 – JUNE 2010 ERROR REPORTING The SD, OTW, OTW1 and OTW2 pins are active-low, open-drain outputs. Their function is for protection-mode signaling to a PWM controller or other system-control device. Any fault resulting in device shutdown is signaled by the SD pin going low. Likewise, OTW and OTW2 goes low when the device junction temperature exceeds 125°C and OTW1 goes low when the junction temperature exceeds 100°C (see the following table). SD OTW1 OTW2, OTW 0 0 0 Overtemperature (OTE) or overload (OLP) or undervoltage (UVP) 0 0 1 Overload (OLP) or undervoltage (UVP). Junction temperature higher than 100°C (overtemperature warning) 0 1 1 Overload (OLP) or undervoltage (UVP) 1 0 0 Junction temperature higher than 125°C (overtemperature warning) 1 0 1 Junction temperature higher than 100°C (overtemperature warning) 1 1 1 Junction temperature lower than 100°C and no OLP or UVP faults (normal operation) DESCRIPTION Note that asserting RESET low forces the SD signal high, independent of faults being present. TI recommends monitoring the OTW signal using the system micro controller and responding to an overtemperature warning signal by, e.g., turning down the volume to prevent further heating of the device resulting in device shutdown (OTE). To reduce external component count, an internal pullup resistor to 3.3V is provided on both SD and OTW outputs. Level compliance for 5V logic can be obtained by adding external pullup resistors to 5V (see the Electrical Characteristics table of this data sheet for further specifications). DEVICE PROTECTION SYSTEM The TAS5614A contains advanced protection circuitry carefully designed to facilitate system integration and ease of use, as well as to safeguard the device from permanent failure due to a wide range of fault conditions such as short circuits, overload, overtemperature, and undervoltage. The TAS5614A responds to a fault by immediately setting the power stage in a high-impedance (Hi-Z) state and asserting the SD pin low. In situations other than overload and overtemperature error (OTE), the device automatically recovers when the fault condition has been removed, i.e., the supply voltage has increased. The device will function on errors, as shown in the following table. BTL Mode PBTL Mode SE Mode Local Error In Turns Off Local Error In Turns Off Local Error In Turns Off A A+B A A+B+C+D A A+B B C C+D D B B C C D D C+D Bootstrap UVP does not shutdown according to the table, it shuts down the respective halfbridge. PIN-TO-PIN SHORT CIRCUIT PROTECTION (PPSC) The PPSC detection system protects the device from permanent damage if a power output pin (OUT_X) is shorted to GND_X or PVDD_X. For comparison, the OC protection system detects an over current after the demodulation filter where PPSC detects shorts directly at the pin before the filter. PPSC detection is performed at startup i.e. when VDD is supplied, consequently a short to either GND_X or PVDD_X after system startup will not activate the PPSC detection system. When PPSC detection is activated by a short on the output, all half bridges are kept in a Hi-Z state until the short is removed, the device then continues the startup sequence and starts switching. The detection is controlled globally by a two step sequence. The first step ensures that there are no shorts from OUT_X to GND_X, the second step tests that there are no shorts from OUT_X to PVDD_X. The total duration of this process is roughly proportional to the capacitance of the output LC filter. The typical duration is Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TAS5614A 19 TAS5614A SLAS712 – JUNE 2010 www.ti.com <15 ms/mF. While the PPSC detection is in progress, SD is kept low, and the device will not react to changes applied to the RESET pins. If no shorts are present the PPSC detection passes, and SD is released. A device reset will not start a new PPSC detection. PPSC detection is enabled in BTL and PBTL output configurations, the detection is not performed in SE mode. To make sure not to trip the PPSC detection system it is recommended not to insert resistive load to GND_X or PVDD_X. OVERTEMPERATURE PROTECTION The two different package options has individual over temperature protection schemes. PHD Package The TAS5614A PHD package option has a three-level temperature-protection system that asserts an active-low warning signal (OTW1) when the device junction temperature exceeds 100°C (typical), (OTW2) when the device junction temperature exceeds 125°C (typical) and, if the device junction temperature exceeds 155°C (typical), the device is put into thermal shutdown, resulting in all half-bridge outputs being set in the high-impedance (Hi-Z) state and SD being asserted low. OTE is latched in this case. To clear the OTE latch, RESET must be asserted. Thereafter, the device resumes normal operation. DKD Package The TAS5614A DKD package option has a two-level temperature-protection system that asserts an active-low warning signal (OTW) when the device junction temperature exceeds 125°C (typical) and, if the device junction temperature exceeds 155°C (typical), the device is put into thermal shutdown, resulting in all half-bridge outputs being set in the high-impedance (Hi-Z) state and SD being asserted low. OTE is latched in this case. To clear the OTE latch, RESET must be asserted. Thereafter, the device resumes normal operation. UNDERVOLTAGE PROTECTION (UVP) AND POWER-ON RESET (POR) The UVP and POR circuits of the TAS5614A fully protect the device in any power-up/down and brownout situation. While powering up, the POR circuit resets the overload circuit (OLP) and ensures that all circuits are fully operational when the GVDD_X and VDD supply voltages reach stated in the Electrical Characteristics table. Although GVDD_X and VDD are independently monitored, a supply voltage drop below the UVP threshold on any VDD or GVDD_X pin results in all half-bridge outputs immediately being set in the high-impedance (Hi-Z) state and SD being asserted low. The device automatically resumes operation when all supply voltages have increased above the UVP threshold. DEVICE RESET When RESET is asserted low, all power-stage FETs in the four half-bridges are forced into a high-impedance (Hi-Z) state. In BTL modes, to accommodate bootstrap charging prior to switching start, asserting the reset input low enables weak pulldown of the half-bridge outputs. In the SE mode, the output is forced into a high impedance state when asserting the reset input low. Asserting reset input low removes any fault information to be signaled on the SD output, i.e., SD is forced high. A rising-edge transition on reset input allows the device to resume operation after an overload fault. To ensure thermal reliability, the rising edge of reset must occur no sooner than 4 ms after the falling edge of SD. SYSTEM DESIGN CONSIDERATION A rising-edge transition on reset input allows the device to execute the startup sequence and starts switching. Apply only audio when the state of READY is high that will start and stop the amplifier without having audible artifacts that is heard in the output transducers. If an overcurrent protection event is introduced the READY signal goes low, hence, filtering is needed if the signal is intended for audio muting in non micro controller systems. The CLIP signal is indicating that the output is approaching clipping. The signal can be used to either an audio volume decrease or intelligent power supply controlling a low and a high rail. The device is inverting the audio signal from input to output. The VREG pin is not recommended to be used as a voltage source for external circuitry. 20 Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TAS5614A TAS5614A www.ti.com SLAS712 – JUNE 2010 PRINTED CIRCUIT BOARD RECOMMENDATION Use an unbroken ground plane to have good low impedance and inductance return path to the power supply for power and audio signals. PCB layout, audio performance and EMI are linked closely together. The circuit contains high fast switching currents; therefore, care must be taken to prevent damaging voltage spikes. Routing the audio input should be kept short and together with the accompanied audio source ground. A local ground area underneath the device is important to keep solid to minimize ground bounce. Netlist for this printed circuit board is generated from the schematic in Figure 12. Note T1: PVDD decoupling bulk capacitors C60-C64 should be as close as possible to the PVDD and GND_X pins, the heat sink sets the distance. Wide traces should be routed on the top layer with direct connection to the pins and without going through vias. No vias or traces should be blocking the current path. Note T2: Close decoupling of PVDD with low impedance X7R ceramic capacitors is placed under the heat sink and close to the pins. Note T3: Heat sink needs to have a good connection to PCB ground. Note T4: Output filter capacitors must be linear in the applied voltage range preferable metal film types. Figure 15. Printed Circuit Board - Top Layer Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TAS5614A 21 TAS5614A SLAS712 – JUNE 2010 www.ti.com Note B1: It is important to have a direct low impedance return path for high current back to the power supply. Keep impedance low from top to bottom side of PCB through a lot of ground vias. Note B2: Bootstrap low impedance X7R ceramic capacitors placed on bottom side providing a short low inductance current loop. Note B3: Return currents from bulk capacitors and output filter capacitors. Figure 16. Printed Circuit Board - Bottom Layer SPACER 22 Submit Documentation Feedback Copyright © 2010, Texas Instruments Incorporated Product Folder Link(s): TAS5614A PACKAGE OPTION ADDENDUM www.ti.com 11-Jun-2010 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) Samples (Requires Login) TAS5614APHD PREVIEW HTQFP PHD 64 90 TBD Call TI Call TI Samples Not Available TAS5614APHDR PREVIEW HTQFP PHD 64 1000 TBD Call TI Call TI Samples Not Available TAS5614PHD ACTIVE HTQFP PHD 64 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-5A-260C-24 HR Purchase Samples TAS5614PHDR ACTIVE HTQFP PHD 64 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-5A-260C-24 HR Request Free Samples (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DLP® Products www.dlp.com Communications and Telecom www.ti.com/communications DSP dsp.ti.com Computers and Peripherals www.ti.com/computers Clocks and Timers www.ti.com/clocks Consumer Electronics www.ti.com/consumer-apps Interface interface.ti.com Energy www.ti.com/energy Logic logic.ti.com Industrial www.ti.com/industrial Power Mgmt power.ti.com Medical www.ti.com/medical Microcontrollers microcontroller.ti.com Security www.ti.com/security RFID www.ti-rfid.com Space, Avionics & Defense www.ti.com/space-avionics-defense RF/IF and ZigBee® Solutions www.ti.com/lprf Video and Imaging www.ti.com/video Wireless www.ti.com/wireless-apps Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2010, Texas Instruments Incorporated