INTEGRATED CIRCUITS DATA SHEET TDA3672 Very low dropout voltage/quiescent current 3.0 V voltage regulator with enable Preliminary specification File under Integrated Circuits, IC01 2000 Apr 26 Philips Semiconductors Preliminary specification Very low dropout voltage/quiescent current 3.0 V voltage regulator with enable TDA3672 – Able to withstand voltages up to 18 V at the output (supply line may be short-circuited) FEATURES • Fixed 3.0 V, 100 mA regulator with enable function – ESD protection on all pins • Supply voltage range up to 33 V (45 V) – DC short-circuit safe to ground and VP of the regulator output • Very low quiescent current of 15 µA (typical value) • Very low dropout voltage – Temperature protection (at Tj > 150 °C). • High ripple rejection • Very high stability: GENERAL DESCRIPTION – Electrolytic capacitors: Equivalent Series Resistance (ESR) < 30 Ω at IREG ≤ 25 mA (see Fig.6) The TDA3672 is a fixed 3.0 V voltage regulator with very low dropout voltage and quiescent current, which operates over a wide supply voltage range. – Other capacitors: 100 nF at 200 µA ≤ IREG ≤ 100 mA. • Pin compatible family TDA3672 to TDA3676 The IC is available as: • Protections: TDA3672AT: VP ≤ 45 V; −40 °C ≤ Tamb ≤ +125 °C and SO8 package (automotive). – Reverse polarity safe (down to −25 V without high reverse current) – Negative transient of 50 V (RS = 10 Ω and t < 100 ms) QUICK REFERENCE DATA SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT Supply VP supply voltage regulator on 3 14.4 45 V Iq quiescent supply current VP = 14.4 V; IREG = 0 mA; VI(EN) = 5 V − 15 30 µA 7.5 ≤ VP ≤ 22 V; IREG = 0.5 mA 2.84 3.0 3.16 V 5.5 V ≤ VP ≤ 45 V; IREG = 0.5 mA 2.81 3.0 3.19 V VP = 14.4 V; 0.5 mA ≤ IREG ≤ 100 mA 2.81 3.0 3.19 V 0.18 0.3 V Voltage regulator VREG VREG(drop) output voltage dropout voltage VP = 2.8 V; IREG = 50 mA; Tamb ≤ 85 °C − ORDERING INFORMATION TYPE NUMBER TDA3672AT 2000 Apr 26 PACKAGE NAME SO8 DESCRIPTION plastic small outline package; 8 leads; body width 3.9 mm 2 VERSION SOT96-1 Philips Semiconductors Preliminary specification Very low dropout voltage/quiescent current 3.0 V voltage regulator with enable TDA3672 BLOCK DIAGRAM handbook, halfpage VP 8 REGULATOR EN 5 1 REG BAND GAP THERMAL PROTECTION TDA3672 2, 3, 6, 7 MBL122 GND Fig.1 Block diagram. PINNING SYMBOL PIN DESCRIPTION REG 1 regulator output GND 2, 3, 6 and 7 ground; note 1 n.c. 4 not connected EN 5 enable input VP 8 supply voltage handbook, halfpage Note REG 1 1. All pins GND are connected to the lead frame and can also be used to reduce the total thermal resistance Rth(j-a) by soldering these pins to a ground plane. The ground plane on the top side of the PCB acts like a heat spreader. 8 VP GND 2 7 GND TDA3672 GND 3 6 GND n.c. 4 5 EN MBL123 Fig.2 Pin configuration. 2000 Apr 26 3 Philips Semiconductors Preliminary specification Very low dropout voltage/quiescent current 3.0 V voltage regulator with enable FUNCTIONAL DESCRIPTION TDA3672 A temperature protection circuit is included, which switches off the regulator output at a junction temperature above 150 °C. The TDA3672 is a fixed 3.0 V regulator which can deliver output currents up to 100 mA. The regulator is available in an SO8 package with fused centre pins connected to the lead frame. The regulator is intended for portable, mains, telephone and automotive applications. To increase the lifetime of batteries, a specially built-in clamp circuit keeps the quiescent current of this regulator very low, also in dropout and full load conditions. A new output circuit guarantees the stability of the regulator for a capacitor output circuit with an ESR up to 20 Ω (see Fig.5). If only a 100 nF capacitor is used, the regulator is fully stable when IREG > 200 µA. This is very attractive as the ESR of an electrolytic capacitor increases strongly at low temperatures (no expensive tantalum capacitor is required). The regulator remains operating down to very low supply voltages and below this voltage it switches off. LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 60134). SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT − 45 V non-operating − −25 V total power dissipation temperature of copper area is 25 °C − 4.1 W Tstg storage temperature non-operating −55 +150 °C Tamb ambient temperature operating −40 +125 °C Tj junction temperature operating −40 +150 °C VP supply voltage VP(rp) reverse polarity supply voltage Ptot THERMAL CHARACTERISTICS SYMBOL PARAMETER CONDITIONS VALUE UNIT Rth(j-a) thermal resistance from junction to ambient in free air; soldered in 125 K/W Rth(j-c) thermal resistance from junction to case to centre pins; soldered in 30 K/W QUALITY SPECIFICATION In accordance with “SNW-FQ-611E”. 2000 Apr 26 4 Philips Semiconductors Preliminary specification Very low dropout voltage/quiescent current 3.0 V voltage regulator with enable TDA3672 CHARACTERISTICS VP = 14.4 V; Tamb = 25 °C; measured in test circuit (see Fig.3); unless otherwise specified. SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT Supply voltage: pin VP VP supply voltage regulator operating; note 1 3 14.4 45 V Iq quiescent current VP = 14.4 V; IREG = 0 mA; VI(EN) = 0 V − 4 15 µA VP = 14.4 V; IREG = 0 mA; VI(EN) = 5 V − 15 30 µA 5.5 V ≤ VP ≤ 22 V; IREG = 10 mA − 0.2 0.5 mA 5.5 V ≤ VP ≤ 22 V; IREG = 50 mA − 1.4 2.5 mA enable off; VREG ≤ 0.8 V −1 − +1.0 V enable on; VREG ≥ 2.7 V 3.0 − 18 V VI(EN) = 5 V − 0.3 − µA Enable input: pin EN VI(EN) II(EN) enable input voltage enable input current Regulator output: pin REG; note 2 VREG output voltage VREG(drop) dropout voltage VREG(stab) long-term output voltage stability ∆VREG(line) line regulation voltage 7.5 V ≤ VP ≤ 22 V; IREG = 0.5 mA 2.84 3.0 3.16 V 0.5 mA ≤ IREG ≤ 100 mA; Tamb ≤ 125 °C 2.81 3.0 3.19 V 5.5 V ≤ VP ≤ 45 V; IREG = 0.5 mA; 2.81 Tamb ≤ 125 °C 3.0 3.19 V − 0.18 0.3 V − 20 − mV/1000 h − 1 30 mV VP = 2.8 V; IREG = 50 mA; Tamb ≤ 85 °C 6.5 V ≤ VP ≤ 22 V; IREG = 0.5 mA 6.5 V ≤ VP ≤ 45 V; IREG = 0.5 mA − 1 50 mV ∆VREG(load) load output regulation voltage 0.5 mA ≤ IREG ≤ 50 mA − 10 50 mV SVRR supply voltage ripple rejection fi = 120 Hz; Vi(ripple) = 1 V (RMS); IREG = 0.5 mA 50 60 − dB IREG(crl) current limit VREG > 2.5 V 0.17 0.25 − A ILO(rp) output leakage current at reverse polarity input VP = −15 V; VREG ≤ 0.3 V − 1 500 µA Notes 1. The regulator output will follow VP if VP < VREG + VREG(drop). 2. Limiting values as applicable for device type TDA3672AT: VP ≤ 45 V and −40 °C ≤ Tamb ≤ +125 °C. 2000 Apr 26 5 Philips Semiconductors Preliminary specification Very low dropout voltage/quiescent current 3.0 V voltage regulator with enable TDA3672 TEST AND APPLICATION INFORMATION MDA961 102 handbook, halfpage ESR (Ω) (1) 10 ndbook, halfpage VP 8 C1 1 µF VREG = 3.0 V C2 10 µF 1 TDA3672 stable region 1 VI(EN) 5 2, 3, 6, 7 MBL125 (2) 10−1 10−1 1 10 C2 (µF) 102 (1) Maximum ESR at 200 µA ≤ IREG ≤ 100 mA. (2) Minimum ESR only when IREG ≤ 200 µA. VI(EN) = 5 V. C1 is optional (to minimize supply noise only). Fig.4 Graph for selecting the value of the output capacitor. Fig.3 Test circuit. Noise The output noise is determined by the value of the output capacitor. The noise figure is measured at a bandwidth of 10 Hz to 100 kHz (see Table 1). Table 1 MDA962 103 handbook, halfpage ESR (Ω) Noise figures 102 OUTPUT CURRENT IREG (mA) NOISE FIGURE (µV) C2 = 10 µF C2 = 47 µF C2 = 100 µF 0.5 550 320 300 50 650 400 400 22 10 stable region 1 Stability The regulator is stabilized with an external capacitor connected to the output. The value of this capacitor can be selected using the diagrams shown in Figs 4 and 5. The following four examples show the effects of the stabilization circuit using different values for the output capacitor. 10−1 1 Fig.5 2000 Apr 26 6 10 102 IREG (mA) 103 ESR as a function of IREG for selecting the value of the output capacitor. Philips Semiconductors Preliminary specification Very low dropout voltage/quiescent current 3.0 V voltage regulator with enable TDA3672 For successful operation of the IC (maximum output current capability) special attention has to be given to the copper area required as heatsink (connected to all GND pins), the thermal capacity of the heatsink and its ability to transfer heat to the external environment. It is possible to reduce the total thermal resistance from 120 to 50 K/W. EXAMPLE 1 The regulator is stabilized with an electrolytic capacitor of 68 µF (ESR = 0.5 Ω). At Tamb = −40 °C, the capacitor value is decreased to 22 µF and the ESR is increased to 3.5 Ω. The regulator will remain stable at a temperature of Tamb = −40 °C. EXAMPLE 2 Application circuit with backup function The regulator is stabilized with an electrolytic capacitor of 10 µF (ESR = 3.3 Ω). At Tamb = −40 °C, the capacitor value is decreased to 3 µF and the ESR is increased to 20 Ω. The regulator will remain stable at a temperature of Tamb = −40 °C. Sometimes a backup function is needed to supply, for example, a microcontroller for a short period of time when the supply voltage spikes to 0 V (or even −1 V). This function can be easily built with the TDA3672 by using a large output capacitor. When the supply voltage is 0 V (or −1 V), only a small current will flow into pin REG from this output capacitor (a few µA). EXAMPLE 3 The regulator is stabilized with a 100 nF MKT capacitor connected to the output. Full stability is guaranteed when the output current is larger then 200 µA. The application circuit is given in Fig.6. Because the thermal influence on this capacitor value is almost zero, the regulator will remain stable at a temperature of Tamb = −40 °C. EXAMPLE 4 The regulator is stabilized with a 100 nF capacitor in parallel with a electrolytic capacitor of 10 µF connected to the output. ndbook, halfpage VP The regulator is now stable under all conditions and independent of: • The ESR of the electrolytic capacitor 8 C1 1 µF VI(EN) • The value of the electrolytic capacitor • The output current. VREG = 3.0 V 1 C2 TDA3672 5 2, 3, 6, 7 MBL124 Application circuits The maximum output current of the regulator equals: 150 – T amb I REG ( max ) = ----------------------------------------------------------R th ( j – a ) × ( V P – V REG ) VI(EN) = 5 V. C1 is optional (to minimize supply noise only). C2 ≤ 4700 µF. 150 – T amb = ----------------------------------------- ( mA ) 100 × ( V P – 3.0 ) Fig.6 Application circuit with backup function. When Tamb = 21 °C and VP = 14 V the maximum output current equals 117 mA. 2000 Apr 26 7 Philips Semiconductors Preliminary specification Very low dropout voltage/quiescent current 3.0 V voltage regulator with enable TDA3672 Additional application information This section gives typical curves for various parameters measured on the TDA3672AT. Standard test conditions are: VP = 14.4 V; Tamb = 25 °C. MDA947 25 MDA949 4 handbook, halfpage handbook, halfpage Iq (µA) Iq (mA) 20 3 15 2 10 1 5 0 0 0 20 10 VP (V) 0 30 10 20 40 30 VP (V) 50 IREG = 0 mA. Fig.7 Quiescent current as a function of the supply voltage. Fig.8 MDA951 2 Quiescent current as a function of high supply voltage. MDA948 0.48 handbook, halfpage handbook, halfpage Iq (mA) (1) Iq (mA) 1.5 0.44 1 0.40 0.5 (2) 0 −40 0.36 0 40 80 120 5 160 Tj (°C) (1) Iq at 50 mA load. (2) Iq at 10 mA load. Fig.9 15 20 VP (V) 25 IREG = 10 mA. Quiescent current as a function of the junction temperature. 2000 Apr 26 10 Fig.10 Quiescent current as a function of the supply voltage. 8 Philips Semiconductors Preliminary specification Very low dropout voltage/quiescent current 3.0 V voltage regulator with enable MDA950 2 TDA3672 MDA952 4 handbook, halfpage handbook, halfpage Iq (mA) Iq (mA) 3 1.8 2 1.6 1 0 1.4 5 10 20 15 VP (V) 0 25 20 40 60 80 100 IREG (mA) IREG = 50 mA. Fig.11 Quiescent current as a function of the supply voltage. Fig.12 Quiescent current as a function of the output current. MGU155 3.10 MGU156 4 handbook, halfpage handbook, halfpage VREG (V) VREG (V) 3 3.05 2 3.00 1 2.95 −50 0 50 100 0 −50 150 200 Tj (°C) 0 50 100 150 200 Tj (°C) IREG = 0 mA. IREG = 0 mA. Fig.13 Output voltage as a function of the junction temperature. Fig.14 Output voltage thermal protection as a function of the junction temperature. 2000 Apr 26 9 Philips Semiconductors Preliminary specification Very low dropout voltage/quiescent current 3.0 V voltage regulator with enable TDA3672 MDA957 500 MGU157 4 handbook, halfpage handbook, halfpage VREG(drop) VREG (mV) (V) 400 3 300 2 200 1 0 100 0 80 40 IREG (mA) 120 0 100 200 IREG (mA) VP = 8 V with pulsed load. Fig.15 Dropout voltage as a function of the output current. Fig.16 Foldback protection mode. MDA956 −30 handbook, halfpage (1) SVRR (dB) −40 (2) −50 (3) (1) −60 (2) −70 10 (3) 102 103 104 f (Hz) 105 C2 = 10 µF. (1) SVRR at RL = 10 kΩ. (2) SVRR at RL = 500 Ω. (3) SVRR at RL = 100 Ω. Fig.17 SVRR as a function of the ripple frequency. 2000 Apr 26 10 300 Philips Semiconductors Preliminary specification Very low dropout voltage/quiescent current 3.0 V voltage regulator with enable TDA3672 PACKAGE OUTLINE SO8: plastic small outline package; 8 leads; body width 3.9 mm SOT96-1 D E A X c y HE v M A Z 5 8 Q A2 A (A 3) A1 pin 1 index θ Lp L 4 1 e detail X w M bp 0 2.5 5 mm scale DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT A max. A1 A2 A3 bp c D (1) E (2) e HE L Lp Q v w y Z (1) mm 1.75 0.25 0.10 1.45 1.25 0.25 0.49 0.36 0.25 0.19 5.0 4.8 4.0 3.8 1.27 6.2 5.8 1.05 1.0 0.4 0.7 0.6 0.25 0.25 0.1 0.7 0.3 0.01 0.019 0.0100 0.014 0.0075 0.20 0.19 0.16 0.15 0.244 0.039 0.028 0.050 0.041 0.228 0.016 0.024 inches 0.010 0.057 0.069 0.004 0.049 0.01 0.01 0.028 0.004 0.012 θ Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic or metal protrusions of 0.25 mm maximum per side are not included. REFERENCES OUTLINE VERSION IEC JEDEC SOT96-1 076E03 MS-012 2000 Apr 26 EIAJ EUROPEAN PROJECTION ISSUE DATE 97-05-22 99-12-27 11 o 8 0o Philips Semiconductors Preliminary specification Very low dropout voltage/quiescent current 3.0 V voltage regulator with enable SOLDERING TDA3672 If wave soldering is used the following conditions must be observed for optimal results: Introduction to soldering surface mount packages • Use a double-wave soldering method comprising a turbulent wave with high upward pressure followed by a smooth laminar wave. This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our “Data Handbook IC26; Integrated Circuit Packages” (document order number 9398 652 90011). • For packages with leads on two sides and a pitch (e): – larger than or equal to 1.27 mm, the footprint longitudinal axis is preferred to be parallel to the transport direction of the printed-circuit board; There is no soldering method that is ideal for all surface mount IC packages. Wave soldering is not always suitable for surface mount ICs, or for printed-circuit boards with high population densities. In these situations reflow soldering is often used. – smaller than 1.27 mm, the footprint longitudinal axis must be parallel to the transport direction of the printed-circuit board. Reflow soldering The footprint must incorporate solder thieves at the downstream end. Reflow soldering requires solder paste (a suspension of fine solder particles, flux and binding agent) to be applied to the printed-circuit board by screen printing, stencilling or pressure-syringe dispensing before package placement. • For packages with leads on four sides, the footprint must be placed at a 45° angle to the transport direction of the printed-circuit board. The footprint must incorporate solder thieves downstream and at the side corners. Several methods exist for reflowing; for example, infrared/convection heating in a conveyor type oven. Throughput times (preheating, soldering and cooling) vary between 100 and 200 seconds depending on heating method. During placement and before soldering, the package must be fixed with a droplet of adhesive. The adhesive can be applied by screen printing, pin transfer or syringe dispensing. The package can be soldered after the adhesive is cured. Typical reflow peak temperatures range from 215 to 250 °C. The top-surface temperature of the packages should preferable be kept below 230 °C. Typical dwell time is 4 seconds at 250 °C. A mildly-activated flux will eliminate the need for removal of corrosive residues in most applications. Wave soldering Manual soldering Conventional single wave soldering is not recommended for surface mount devices (SMDs) or printed-circuit boards with a high component density, as solder bridging and non-wetting can present major problems. Fix the component by first soldering two diagonally-opposite end leads. Use a low voltage (24 V or less) soldering iron applied to the flat part of the lead. Contact time must be limited to 10 seconds at up to 300 °C. To overcome these problems the double-wave soldering method was specifically developed. When using a dedicated tool, all other leads can be soldered in one operation within 2 to 5 seconds between 270 and 320 °C. 2000 Apr 26 12 Philips Semiconductors Preliminary specification Very low dropout voltage/quiescent current 3.0 V voltage regulator with enable TDA3672 Suitability of surface mount IC packages for wave and reflow soldering methods SOLDERING METHOD PACKAGE REFLOW(1) WAVE BGA, SQFP not suitable HLQFP, HSQFP, HSOP, HTSSOP, SMS not PLCC(3), SO, SOJ LQFP, QFP, TQFP SSOP, TSSOP, VSO suitable suitable(2) suitable suitable suitable not recommended(3)(4) suitable not recommended(5) suitable Notes 1. All surface mount (SMD) packages are moisture sensitive. Depending upon the moisture content, the maximum temperature (with respect to time) and body size of the package, there is a risk that internal or external package cracks may occur due to vaporization of the moisture in them (the so called popcorn effect). For details, refer to the Drypack information in the “Data Handbook IC26; Integrated Circuit Packages; Section: Packing Methods”. 2. These packages are not suitable for wave soldering as a solder joint between the printed-circuit board and heatsink (at bottom version) can not be achieved, and as solder may stick to the heatsink (on top version). 3. If wave soldering is considered, then the package must be placed at a 45° angle to the solder wave direction. The package footprint must incorporate solder thieves downstream and at the side corners. 4. Wave soldering is only suitable for LQFP, TQFP and QFP packages with a pitch (e) equal to or larger than 0.8 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.65 mm. 5. Wave soldering is only suitable for SSOP and TSSOP packages with a pitch (e) equal to or larger than 0.65 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.5 mm. 2000 Apr 26 13 Philips Semiconductors Preliminary specification Very low dropout voltage/quiescent current 3.0 V voltage regulator with enable TDA3672 DATA SHEET STATUS DATA SHEET STATUS PRODUCT STATUS DEFINITIONS (1) Objective specification Development This data sheet contains the design target or goal specifications for product development. Specification may change in any manner without notice. Preliminary specification Qualification This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Product specification Production This data sheet contains final specifications. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Note 1. Please consult the most recently issued data sheet before initiating or completing a design. DEFINITIONS DISCLAIMERS Short-form specification The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Life support applications These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Limiting values definition Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Right to make changes Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no licence or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Application information Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. 2000 Apr 26 14 Philips Semiconductors Preliminary specification Very low dropout voltage/quiescent current 3.0 V voltage regulator with enable NOTES 2000 Apr 26 15 TDA3672 Philips Semiconductors – a worldwide company Argentina: see South America Australia: 3 Figtree Drive, HOMEBUSH, NSW 2140, Tel. +61 2 9704 8141, Fax. +61 2 9704 8139 Austria: Computerstr. 6, A-1101 WIEN, P.O. Box 213, Tel. +43 1 60 101 1248, Fax. +43 1 60 101 1210 Belarus: Hotel Minsk Business Center, Bld. 3, r. 1211, Volodarski Str. 6, 220050 MINSK, Tel. +375 172 20 0733, Fax. +375 172 20 0773 Belgium: see The Netherlands Brazil: see South America Bulgaria: Philips Bulgaria Ltd., Energoproject, 15th floor, 51 James Bourchier Blvd., 1407 SOFIA, Tel. +359 2 68 9211, Fax. +359 2 68 9102 Canada: PHILIPS SEMICONDUCTORS/COMPONENTS, Tel. +1 800 234 7381, Fax. +1 800 943 0087 China/Hong Kong: 501 Hong Kong Industrial Technology Centre, 72 Tat Chee Avenue, Kowloon Tong, HONG KONG, Tel. +852 2319 7888, Fax. +852 2319 7700 Colombia: see South America Czech Republic: see Austria Denmark: Sydhavnsgade 23, 1780 COPENHAGEN V, Tel. +45 33 29 3333, Fax. +45 33 29 3905 Finland: Sinikalliontie 3, FIN-02630 ESPOO, Tel. +358 9 615 800, Fax. +358 9 6158 0920 France: 51 Rue Carnot, BP317, 92156 SURESNES Cedex, Tel. +33 1 4099 6161, Fax. +33 1 4099 6427 Germany: Hammerbrookstraße 69, D-20097 HAMBURG, Tel. +49 40 2353 60, Fax. +49 40 2353 6300 Hungary: see Austria India: Philips INDIA Ltd, Band Box Building, 2nd floor, 254-D, Dr. Annie Besant Road, Worli, MUMBAI 400 025, Tel. +91 22 493 8541, Fax. +91 22 493 0966 Indonesia: PT Philips Development Corporation, Semiconductors Division, Gedung Philips, Jl. Buncit Raya Kav.99-100, JAKARTA 12510, Tel. +62 21 794 0040 ext. 2501, Fax. +62 21 794 0080 Ireland: Newstead, Clonskeagh, DUBLIN 14, Tel. +353 1 7640 000, Fax. +353 1 7640 200 Israel: RAPAC Electronics, 7 Kehilat Saloniki St, PO Box 18053, TEL AVIV 61180, Tel. +972 3 645 0444, Fax. +972 3 649 1007 Italy: PHILIPS SEMICONDUCTORS, Via Casati, 23 - 20052 MONZA (MI), Tel. +39 039 203 6838, Fax +39 039 203 6800 Japan: Philips Bldg 13-37, Kohnan 2-chome, Minato-ku, TOKYO 108-8507, Tel. +81 3 3740 5130, Fax. +81 3 3740 5057 Korea: Philips House, 260-199 Itaewon-dong, Yongsan-ku, SEOUL, Tel. +82 2 709 1412, Fax. +82 2 709 1415 Malaysia: No. 76 Jalan Universiti, 46200 PETALING JAYA, SELANGOR, Tel. +60 3 750 5214, Fax. +60 3 757 4880 Mexico: 5900 Gateway East, Suite 200, EL PASO, TEXAS 79905, Tel. +9-5 800 234 7381, Fax +9-5 800 943 0087 Middle East: see Italy Netherlands: Postbus 90050, 5600 PB EINDHOVEN, Bldg. VB, Tel. +31 40 27 82785, Fax. +31 40 27 88399 New Zealand: 2 Wagener Place, C.P.O. Box 1041, AUCKLAND, Tel. +64 9 849 4160, Fax. +64 9 849 7811 Norway: Box 1, Manglerud 0612, OSLO, Tel. +47 22 74 8000, Fax. +47 22 74 8341 Pakistan: see Singapore Philippines: Philips Semiconductors Philippines Inc., 106 Valero St. Salcedo Village, P.O. Box 2108 MCC, MAKATI, Metro MANILA, Tel. +63 2 816 6380, Fax. +63 2 817 3474 Poland: Al.Jerozolimskie 195 B, 02-222 WARSAW, Tel. +48 22 5710 000, Fax. +48 22 5710 001 Portugal: see Spain Romania: see Italy Russia: Philips Russia, Ul. Usatcheva 35A, 119048 MOSCOW, Tel. +7 095 755 6918, Fax. +7 095 755 6919 Singapore: Lorong 1, Toa Payoh, SINGAPORE 319762, Tel. +65 350 2538, Fax. +65 251 6500 Slovakia: see Austria Slovenia: see Italy South Africa: S.A. PHILIPS Pty Ltd., 195-215 Main Road Martindale, 2092 JOHANNESBURG, P.O. Box 58088 Newville 2114, Tel. +27 11 471 5401, Fax. +27 11 471 5398 South America: Al. Vicente Pinzon, 173, 6th floor, 04547-130 SÃO PAULO, SP, Brazil, Tel. +55 11 821 2333, Fax. +55 11 821 2382 Spain: Balmes 22, 08007 BARCELONA, Tel. +34 93 301 6312, Fax. +34 93 301 4107 Sweden: Kottbygatan 7, Akalla, S-16485 STOCKHOLM, Tel. +46 8 5985 2000, Fax. +46 8 5985 2745 Switzerland: Allmendstrasse 140, CH-8027 ZÜRICH, Tel. +41 1 488 2741 Fax. +41 1 488 3263 Taiwan: Philips Semiconductors, 6F, No. 96, Chien Kuo N. Rd., Sec. 1, TAIPEI, Taiwan Tel. +886 2 2134 2886, Fax. +886 2 2134 2874 Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd., 209/2 Sanpavuth-Bangna Road Prakanong, BANGKOK 10260, Tel. +66 2 745 4090, Fax. +66 2 398 0793 Turkey: Yukari Dudullu, Org. San. Blg., 2.Cad. Nr. 28 81260 Umraniye, ISTANBUL, Tel. +90 216 522 1500, Fax. +90 216 522 1813 Ukraine: PHILIPS UKRAINE, 4 Patrice Lumumba str., Building B, Floor 7, 252042 KIEV, Tel. +380 44 264 2776, Fax. +380 44 268 0461 United Kingdom: Philips Semiconductors Ltd., 276 Bath Road, Hayes, MIDDLESEX UB3 5BX, Tel. +44 208 730 5000, Fax. +44 208 754 8421 United States: 811 East Arques Avenue, SUNNYVALE, CA 94088-3409, Tel. +1 800 234 7381, Fax. +1 800 943 0087 Uruguay: see South America Vietnam: see Singapore Yugoslavia: PHILIPS, Trg N. Pasica 5/v, 11000 BEOGRAD, Tel. +381 11 3341 299, Fax.+381 11 3342 553 For all other countries apply to: Philips Semiconductors, International Marketing & Sales Communications, Building BE-p, P.O. Box 218, 5600 MD EINDHOVEN, The Netherlands, Fax. +31 40 27 24825 Internet: http://www.semiconductors.philips.com SCA 69 © Philips Electronics N.V. 2000 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. Printed in The Netherlands 753503/25/01/pp16 Date of release: 2000 Apr 26 Document order number: 9397 750 06704