PHILIPS TDA6106Q

INTEGRATED CIRCUITS
DATA SHEET
TDA6106Q
Video output amplifier
Product specification
File under Integrated Circuits, IC02
1997 Mar 03
Philips Semiconductors
Product specification
Video output amplifier
TDA6106Q
FEATURES
GENERAL DESCRIPTION
• No external heatsink required
The TDA6106Q is a monolithic video output amplifier with
a 6 MHz bandwidth and is contained in a 9-lead plastic
DIL-bent-SIL medium power package. The device uses
high-voltage DMOS technology and is intended to drive
the cathode of a CRT. To obtain maximum performance,
the amplifier should be used with black current control.
• Black current measurement output for Automatic Black
current Stabilization (ABS)
• Internal 2.5 V reference circuit
• Internal protection against positive appearing CRT
flashover discharges
• Single supply voltage of 200 V
• Simple application with a variety of colour decoders
• Controlled switch-off behaviour.
ORDERING INFORMATION
PACKAGE
TYPE NUMBER
NAME
TDA6106Q
DESCRIPTION
DBS9MPF
VERSION
plastic DIL-bent-SIL medium power package with fin; 9 leads
SOT111-1
BLOCK DIAGRAM
handbook, full pagewidth
feedback
output
supply voltage
6
n.c.
n.c.
n.c.
9
1
2
7
MIRROR 1
in
MIRROR 2
out
Vbias
out
1×
in
8
1×
TDA6106Q
CURRENT
SOURCE
5
inverting
input
3
− DIFFERENTIAL +
STAGE
out
out
out
out
MIRROR 3
black current
measurement
output
in
gnd
4
ground
(substrate)
Fig.1 Block diagram.
1997 Mar 03
cathode
output
2
MBG343
Philips Semiconductors
Product specification
Video output amplifier
TDA6106Q
PINNING
SYMBOL
PIN
DESCRIPTION
n.c.
1
not connected
n.c.
2
not connected
Vin
3
inverting input voltage
GND
4
ground, substrate
Iom
5
black current measurement output
VDD
6
n.c.
handbook, halfpage
n.c.
1
n.c.
2
Vin
3
GND
4
supply voltage
Iom
5
7
not connected
VDD
6
Voc
8
cathode output voltage
n.c.
7
Vof
9
feedback output voltage
Voc
8
Vof
9
TDA6106Q
MBG342
Fig.2 Pin configuration.
LIMITING VALUES
In accordance with the Absolute Maximum Rating System (IEC 134); voltages with respect to pin 4 (ground) unless
otherwise specified; currents specified as in Fig.1.
SYMBOL
PARAMETER
CONDITIONS
MIN.
MAX.
UNIT
VDD
supply voltage
0
250
V
Vin
inverting input voltage
0
8
V
Vom
black current measurement output voltage
0
6
V
Voc
cathode DC output voltage
0
VDD
V
Vof
feedback output voltage
0
VDD
V
Ioc(l)
low non-repetitive peak cathode output
current
flashover discharge = 100 µC;
note 1
0
5
A
Ioc(h)
high non-repetitive peak cathode output
current
flashover discharge = 100 nC;
note 2
0
10
A
Pmax
maximum power dissipation
0
tbf
W
Tstg
storage temperature
−55
+150
°C
Tj
junction temperature
−20
+150
°C
Vesd
electrostatic discharge
note 3
−2000
+2000
V
note 4
−300
+300
V
Notes
1. The cathode output is protected against peak currents (caused by positive voltage peaks during high-resistance
flash) of 5 A maximum with a charge content of 100 µC.
2. The cathode output is also protected against peak currents (caused by positive voltage peaks during low-resistance
flash) of 10 A maximum with a charge content of 100 nC.
3. Human body model: equivalent to discharging a 100 pF capacitor through a 1.5 kΩ resistor.
4. Machine model: equivalent to discharging a 200 pF capacitor through a 0 Ω resistor.
1997 Mar 03
3
Philips Semiconductors
Product specification
Video output amplifier
TDA6106Q
HANDLING
Inputs and outputs are protected against electrostatic discharge in normal handling. However, to be totally safe, it is
desirable to take normal precautions appropriate to handling MOS devices (see “Handling MOS Devices” ).
QUALITY SPECIFICATION
Quality specification “SNW-FQ-611 part E” is applicable, except for ESD Human body model see Chapter “Limiting
values”, and can be found in the “Quality reference handbook” (ordering number 9397 750 00192).
THERMAL CHARACTERISTICS
PARAMETER(1)
SYMBOL
VALUE
UNIT
Rth j-a
thermal resistance from junction to ambient in free air
56
K/W
Rth j-c
thermal resistance from junction to case
12
K/W
Note
1. External heatsink not required.
CHARACTERISTICS
Operating range: Tamb = −20 to +65 °C; VDD = 180 to 210 V (see note 1), Vom = 1.4 to 6 V.
Test conditions: Tamb = 25 °C; VDD = 200 V; Vom = 4 V; CL = 10 pF (CL consists of parasitic and cathode capacitance);
measured in test circuit of Fig.5; unless otherwise specified.
SYMBOL
PARAMETER
CONDITIONS
IDD
quiescent voltage supply current
VocDC = 100 V
Ibias
input bias current (pin 3)
Vint
Iom(os)
offset current of black current
measurement output
∆VTint
MIN.
TYP.
MAX.
UNIT
2.8
3.0
3.3
mA
VocDC = 100 V
0
−
20
µA
internal reference voltage input stage VocDC = 100 V
−
2.5
−
V
Ioc = 0 µA;
Vin = 1.5 to +3.5 V;
Vom = 1.4 to 6 V
−10
0
+10
µA
temperature drift of internal
reference voltage input stage
VocDC = 100 V
−
0.5
−
mV/K
∆I om
-----------∆I oc
linearity of current transfer
Ioc = −10 µA to 3 mA;
Vin = 1.5 to +3.5 V;
Vom = 1.4 to 6 V
0.9
1.0
1.1
Iof(max)
maximum peak output current (pin 9)
Voc = 20 V to VDD −30 V
−
25
−
Voc(min)
minimum output voltage (pin 8)
Vin = 3.5 V
−
7
12
V
Voc(max)
maximum output voltage (pin 8)
Vin = 1.5 V
VDD − 14
VDD − 10
−
V
GB
gain bandwidth product of open-loop
gain Vos/Vi, dm
f = 500 kHz;
VocDC = 100 V
−
0.52
−
GHz
BWS
small signal bandwidth
VocAC = 60 V (p-p);
VocDC = 100 V
5
6
−
MHz
BWL
large signal bandwidth
VocAC = 100 V (p-p);
VocDC = 100 V
4.7
5.7
−
MHz
1997 Mar 03
4
mA
Philips Semiconductors
Product specification
Video output amplifier
SYMBOL
PARAMETER
TDA6106Q
CONDITIONS
MIN.
TYP.
MAX.
UNIT
tpd
cathode output propagation delay
time 50% input to 50% output
Voc = 50 to 150 V square
wave; f < 1 MHz;
trin = tfin = 40 ns;
see Figs 3 and 4
38
49
60
ns
tr
cathode output rise time 10% output
to 90% output
Voc = 50 to 150 V square
wave; f < 1 MHz;
tfin = 40 ns; see Fig.4
62
74
87
ns
tf
cathode output fall time 90% output to Voc = 150 to 50 V square
10% output
wave; f < 1 MHz;
trin = 40 ns; see Fig.4
62
74
87
ns
ts
settling time 50% input to
(99% < output < 101%)
Voc = 50 to 150 V square
wave; f < 1 MHz;
trin = tfin = 40 ns;
see Figs 3 and 4
−
−
350
ns
SR
slew rate between 50 and 150 V
Vin = 2 V (p-p) square
wave; f < 1 MHz;
trin = tfin = 40 ns
−
1200
−
V/µs
OV
cathode output voltage overshoot
Voc = 50 to 150 V square
wave; f < 1 MHz;
trin = tfin = 40 ns;
see Figs 3 and 4
−
1
−
%
PSRR
power supply rejection ratio
f < 50 kHz; note 2
−
60
−
dB
Notes
1. The rating of supply voltage is 250 V, but because of flash the maximum operating range for supply voltage is 210 V.
2. PSSR: The ratio of the change in supply voltage to the change in input voltage when there is no change in output
voltage.
1997 Mar 03
5
Philips Semiconductors
Product specification
Video output amplifier
TDA6106Q
x
Vi
0
t
x
ts
overshoot (in %)
Voc
151
150
140
149
100
60
50
t
tr
MGA974
t pd
Fig.3 Output voltage (pin 8 rising edge) as a function of AC input signal.
1997 Mar 03
6
Philips Semiconductors
Product specification
Video output amplifier
TDA6106Q
x
Vi
0
t
x
ts
150
140
Voc
100
overshoot (in %)
51
60
50
49
t
tf
MGA975
t pd
Fig.4 Output voltage (pin 8 falling edge) as a function of AC input signal.
Flashover protection
VDD to GND must be decoupled:
The TDA6106Q incorporates a protection diode against
CRT flashover discharges that clamp the cathode output
voltage to a maximum of VDD + Vdiode. To limit the diode
current, an external 1.5 kΩ carbon high-voltage resistor in
series with the cathode output and a 2 kV spark gap are
needed (for this resistor-value, the CRT has to be
connected to the main PCB). This addition produces an
increase in the rise and fall times of approximately 7.5 ns
and a decrease in the overshoot of approximately 1.3%.
1. With a capacitor larger than 20 nF with good HF
behaviour (e.g. foil). This capacitor must be placed as
close as possible to pins 6 and 4, but definitely within
5 mm.
1997 Mar 03
2. With a capacitor larger than10 µF on the picture tube
base print (shared by three output stages).
Switch-off behaviour
The output pins of the TDA6106Q are still under the control
of the input pin for a supply voltage down to approximately
30 V.
7
Philips Semiconductors
Product specification
Video output amplifier
TDA6106Q
TEST AND APPLICATION INFORMATION
Cpar
handbook, full pagewidth
Rfb
C1
Vin
R10 100 kΩ
22 nF
R9
C2
866 Ω
200 V
C6
100 nF
22 µF
Cn
560 pF
6
R1
50 Ω
3
0.98 mA
9
TDA6106Q 8
4
C8
5
C7
A
3.2 pF
Vom
4V
6.8 pF
R3
20 MΩ
probe
C9
136 pF
R2
1 MΩ
GND
MBG344
Cpar = 150 fF.
Fig.5 Test circuit with feedback factor 1⁄116.
Dissipation
The dynamic dissipation equals:
With respect to dissipation, distinction must be made
between static dissipation (independent of frequency) and
dynamic dissipation (proportional to frequency).
P dyn = V DD × ( C L + C fb + C int ) × f × V o ( p – p ) × b
Where:
CL = load capacitance.
The static dissipation of the TDA6106Q is due to supply
currents and load currents in the feedback network and
CRT.
P stat
Cfb = feedback capacitance.
Cint = internal load capacitance (≈ 4 pF).
f = input frequency.
 V of 
= V DD × I DD + V oc × I oc – V of ×  -------- 
 R fb 
Vo(p-p) = output voltage (peak-to-peak value).
b = non-blanking duty-cycle.
Where:
The IC must be mounted on the picture tube base print to
minimize the load capacitance (CL).
Rfb = value of feedback resistor.
Ioc = DC value of cathode current.
1997 Mar 03
8
Philips Semiconductors
Product specification
Video output amplifier
TDA6106Q
INTERNAL PIN CONFIGURATION
handbook, full pagewidth
GND
VDD
4
6
from
input
circuit
TDA6106Q
esd
esd
esd
Vin
9
Vbias
from
reference
circuit
Vof
from
input
circuit
3
esd
flash
prot.
Iom
esd
from
pin 9
5
flash
prot.
8
from
pin 9
6.8 V
esd
from
reference
circuit
to BCS-circuit
output
MBG345
Fig.6 Internal pin configuration.
1997 Mar 03
9
Voc
Philips Semiconductors
Product specification
Video output amplifier
TDA6106Q
PACKAGE OUTLINE
DBS9MPF: plastic DIL-bent-SIL medium power package with fin; 9 leads
SOT111-1
D
D1
A2
q
P
P1
Q
A3
q2
q1
A
seating plane
A4
E
pin 1 index
c
L
1
9
e2
b
e
Z
b2
0
θ
w M
b1
5
10 mm
scale
DIMENSIONS (mm are the original dimensions)
UNIT
A
mm
18.5
17.8
A2
A3
max.
3.7
8.7
8.0
A4
b
b1
b2
c
D (1)
D1
E (1)
e
e2
15.5 1.40 0.67 1.40 0.48 21.8 21.4 6.48 2.54 2.54
15.1 1.14 0.50 1.14 0.38 21.4 20.7 6.20
L
P
P1
3.9
3.4
2.75
2.50
3.4
3.2
Q
q
1.75 15.1
1.55 14.9
q1
q2
w
Z (1)
max.
θ
4.4
4.2
5.9
5.7
0.25
1.0
65o
55o
Note
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
OUTLINE
VERSION
REFERENCES
IEC
JEDEC
EIAJ
ISSUE DATE
92-11-17
95-03-11
SOT111-1
1997 Mar 03
EUROPEAN
PROJECTION
10
Philips Semiconductors
Product specification
Video output amplifier
TDA6106Q
The device may be mounted up to the seating plane, but
the temperature of the plastic body must not exceed the
specified maximum storage temperature (Tstg max). If the
printed-circuit board has been pre-heated, forced cooling
may be necessary immediately after soldering to keep the
temperature within the permissible limit.
SOLDERING
Introduction
There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mounted components are mixed
on one printed-circuit board. However, wave soldering is
not always suitable for surface mounted ICs, or for
printed-circuits with high population densities. In these
situations reflow soldering is often used.
Repairing soldered joints
Apply a low voltage soldering iron (less than 24 V) to the
lead(s) of the package, below the seating plane or not
more than 2 mm above it. If the temperature of the
soldering iron bit is less than 300 °C it may remain in
contact for up to 10 seconds. If the bit temperature is
between 300 and 400 °C, contact may be up to 5 seconds.
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our “IC Package Databook” (order code 9398 652 90011).
Soldering by dipping or by wave
The maximum permissible temperature of the solder is
260 °C; solder at this temperature must not be in contact
with the joint for more than 5 seconds. The total contact
time of successive solder waves must not exceed
5 seconds.
DEFINITIONS
Data sheet status
Objective specification
This data sheet contains target or goal specifications for product development.
Preliminary specification
This data sheet contains preliminary data; supplementary data may be published later.
Product specification
This data sheet contains final product specifications.
Limiting values
Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or
more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation
of the device at these or at any other conditions above those given in the Characteristics sections of the specification
is not implied. Exposure to limiting values for extended periods may affect device reliability.
Application information
Where application information is given, it is advisory and does not form part of the specification.
LIFE SUPPORT APPLICATIONS
These products are not designed for use in life support appliances, devices, or systems where malfunction of these
products can reasonably be expected to result in personal injury. Philips customers using or selling these products for
use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such
improper use or sale.
1997 Mar 03
11
Philips Semiconductors – a worldwide company
Argentina: see South America
Australia: 34 Waterloo Road, NORTH RYDE, NSW 2113,
Tel. +61 2 9805 4455, Fax. +61 2 9805 4466
Austria: Computerstr. 6, A-1101 WIEN, P.O. Box 213,
Tel. +43 1 60 101, Fax. +43 1 60 101 1210
Belarus: Hotel Minsk Business Center, Bld. 3, r. 1211, Volodarski Str. 6,
220050 MINSK, Tel. +375 172 200 733, Fax. +375 172 200 773
Belgium: see The Netherlands
Brazil: see South America
Bulgaria: Philips Bulgaria Ltd., Energoproject, 15th floor,
51 James Bourchier Blvd., 1407 SOFIA,
Tel. +359 2 689 211, Fax. +359 2 689 102
Canada: PHILIPS SEMICONDUCTORS/COMPONENTS,
Tel. +1 800 234 7381
China/Hong Kong: 501 Hong Kong Industrial Technology Centre,
72 Tat Chee Avenue, Kowloon Tong, HONG KONG,
Tel. +852 2319 7888, Fax. +852 2319 7700
Colombia: see South America
Czech Republic: see Austria
Denmark: Prags Boulevard 80, PB 1919, DK-2300 COPENHAGEN S,
Tel. +45 32 88 2636, Fax. +45 31 57 1949
Finland: Sinikalliontie 3, FIN-02630 ESPOO,
Tel. +358 9 615800, Fax. +358 9 61580/xxx
France: 4 Rue du Port-aux-Vins, BP317, 92156 SURESNES Cedex,
Tel. +33 1 40 99 6161, Fax. +33 1 40 99 6427
Germany: Hammerbrookstraße 69, D-20097 HAMBURG,
Tel. +49 40 23 53 60, Fax. +49 40 23 536 300
Greece: No. 15, 25th March Street, GR 17778 TAVROS/ATHENS,
Tel. +30 1 4894 339/239, Fax. +30 1 4814 240
Hungary: see Austria
India: Philips INDIA Ltd, Shivsagar Estate, A Block, Dr. Annie Besant Rd.
Worli, MUMBAI 400 018, Tel. +91 22 4938 541, Fax. +91 22 4938 722
Indonesia: see Singapore
Ireland: Newstead, Clonskeagh, DUBLIN 14,
Tel. +353 1 7640 000, Fax. +353 1 7640 200
Israel: RAPAC Electronics, 7 Kehilat Saloniki St, TEL AVIV 61180,
Tel. +972 3 645 0444, Fax. +972 3 649 1007
Italy: PHILIPS SEMICONDUCTORS, Piazza IV Novembre 3,
20124 MILANO, Tel. +39 2 6752 2531, Fax. +39 2 6752 2557
Japan: Philips Bldg 13-37, Kohnan 2-chome, Minato-ku, TOKYO 108,
Tel. +81 3 3740 5130, Fax. +81 3 3740 5077
Korea: Philips House, 260-199 Itaewon-dong, Yongsan-ku, SEOUL,
Tel. +82 2 709 1412, Fax. +82 2 709 1415
Malaysia: No. 76 Jalan Universiti, 46200 PETALING JAYA, SELANGOR,
Tel. +60 3 750 5214, Fax. +60 3 757 4880
Mexico: 5900 Gateway East, Suite 200, EL PASO, TEXAS 79905,
Tel. +9-5 800 234 7381
Middle East: see Italy
Netherlands: Postbus 90050, 5600 PB EINDHOVEN, Bldg. VB,
Tel. +31 40 27 82785, Fax. +31 40 27 88399
New Zealand: 2 Wagener Place, C.P.O. Box 1041, AUCKLAND,
Tel. +64 9 849 4160, Fax. +64 9 849 7811
Norway: Box 1, Manglerud 0612, OSLO,
Tel. +47 22 74 8000, Fax. +47 22 74 8341
Philippines: Philips Semiconductors Philippines Inc.,
106 Valero St. Salcedo Village, P.O. Box 2108 MCC, MAKATI,
Metro MANILA, Tel. +63 2 816 6380, Fax. +63 2 817 3474
Poland: Ul. Lukiska 10, PL 04-123 WARSZAWA,
Tel. +48 22 612 2831, Fax. +48 22 612 2327
Portugal: see Spain
Romania: see Italy
Russia: Philips Russia, Ul. Usatcheva 35A, 119048 MOSCOW,
Tel. +7 095 755 6918, Fax. +7 095 755 6919
Singapore: Lorong 1, Toa Payoh, SINGAPORE 1231,
Tel. +65 350 2538, Fax. +65 251 6500
Slovakia: see Austria
Slovenia: see Italy
South Africa: S.A. PHILIPS Pty Ltd., 195-215 Main Road Martindale,
2092 JOHANNESBURG, P.O. Box 7430 Johannesburg 2000,
Tel. +27 11 470 5911, Fax. +27 11 470 5494
South America: Rua do Rocio 220, 5th floor, Suite 51,
04552-903 São Paulo, SÃO PAULO - SP, Brazil,
Tel. +55 11 821 2333, Fax. +55 11 829 1849
Spain: Balmes 22, 08007 BARCELONA,
Tel. +34 3 301 6312, Fax. +34 3 301 4107
Sweden: Kottbygatan 7, Akalla, S-16485 STOCKHOLM,
Tel. +46 8 632 2000, Fax. +46 8 632 2745
Switzerland: Allmendstrasse 140, CH-8027 ZÜRICH,
Tel. +41 1 488 2686, Fax. +41 1 481 7730
Taiwan: Philips Semiconductors, 6F, No. 96, Chien Kuo N. Rd., Sec. 1,
TAIPEI, Taiwan Tel. +886 2 2134 2870, Fax. +886 2 2134 2874
Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd.,
209/2 Sanpavuth-Bangna Road Prakanong, BANGKOK 10260,
Tel. +66 2 745 4090, Fax. +66 2 398 0793
Turkey: Talatpasa Cad. No. 5, 80640 GÜLTEPE/ISTANBUL,
Tel. +90 212 279 2770, Fax. +90 212 282 6707
Ukraine: PHILIPS UKRAINE, 4 Patrice Lumumba str., Building B, Floor 7,
252042 KIEV, Tel. +380 44 264 2776, Fax. +380 44 268 0461
United Kingdom: Philips Semiconductors Ltd., 276 Bath Road, Hayes,
MIDDLESEX UB3 5BX, Tel. +44 181 730 5000, Fax. +44 181 754 8421
United States: 811 East Arques Avenue, SUNNYVALE, CA 94088-3409,
Tel. +1 800 234 7381
Uruguay: see South America
Vietnam: see Singapore
Yugoslavia: PHILIPS, Trg N. Pasica 5/v, 11000 BEOGRAD,
Tel. +381 11 625 344, Fax.+381 11 635 777
For all other countries apply to: Philips Semiconductors, Marketing & Sales Communications,
Building BE-p, P.O. Box 218, 5600 MD EINDHOVEN, The Netherlands, Fax. +31 40 27 24825
Internet: http://www.semiconductors.philips.com
© Philips Electronics N.V. 1997
SCA53
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner.
The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed
without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license
under patent- or other industrial or intellectual property rights.
Printed in The Netherlands
547047/1200/01/pp12
Date of release: 1997 Mar 03
Document order number:
9397 750 01869