TDA7245 5W AUDIO AMPLIFIER WITH MUTING AND STAND-BY MUTING AND STAND-BY FUNCTIONS VOLTAGE RANGE UP TO 30V HIGH SUPPLY VOLTAGE REJECTION SVR TYP = 50dB (f = 100Hz) MUSIC POWER = 12W (RL = 4Ω, d = 10%) PROTECTION AGAINST CHIP OVER TEMPERATURE Powerdip 9+9 DESCRIPTION The TDA7245 is a monolithic integrated circuit in 9+9 POWERDIP package, intended for use as ORDERING NUMBER: TDA7245 low frequency power amplifier in a wide range of applications in radio and TV sets. Figure 1: Test and Application Circuit March 1995 1/11 TDA7245 ABSOLUTE MAXIMUM RATINGS Symbol Parameter Value Unit VS Supply Voltage 30 V IO Output Peak Current (non repetitive t = 100µs) 3 A IO Output Peak Current (repetitive, f > 20Hz) 2.5 A Ptot Power Dissipation at Tamb = 80°C at T case = 70°C 1 6 W W Tstg, Tj Storage and junction Temperature -40 to 150 °C PIN CONNECTION (Top view) THERMAL DATA Symbol Rth j-case Rth j-amb 2/11 Description Thermal Resistance junction-case Thermal Resistance junction-ambient Max Max Value Unit 15 70 °C/W °C/W TDA7245 ELECTRICAL CHARACTERISTICS (Refer to the test circuit, Tamb = 25°C, f = 1kHz; unless otherwise specified). Symbol Parameter Test Condition Min. Typ. Max. Unit 30 V 11.6 V 17 21 35 mA mA VS Supply Voltage VO Quiescent Output Voltage VS = 24V Id Quiescent Drain Current VS = 14V VS = 28V d = 1%, f = 1KHz VS = 14V, R L = 4Ω VS = 18V, R L = 8Ω 4 4 W W 5 5 W W 12 W PO Output Power 12 d = 10%, f = 1KHz VS = 14V, R L = 4Ω VS = 18V, R L = 8Ω 4 Music Power (*) VS = 24V, d = 10%, RL = 4Ω d RI Harmonic Distortion VS = 14V, R L = 4Ω, PO = 50mW to 3W f = 1KHz f = 10KHz 0.15 0.8 VS = 18V, R L = 8Ω, PO = 50mW to 3.5W f = 1KHz f = 10KHz 0.12 0.5 % % VS = 22V, R L = 16Ω, PO = 50mW to 3W f = 1KHz f = 10KHz 0.08 0.4 % % Input Impedance f = 1kHz BW Small signal bandwidth (-3dB) PO = 1W; R L = 4Ω VS = 14V GV Voltage Gain (open loop) f = 1kHz GV Voltage Gain (closed loop) f = 1kHz eN Total Input Noise B = 22 - 22,000Hz R s = 50Ω R s = 1kΩ R s = 10kΩ S/N Signal to Noise Ratio VS = 18V; RL = 8Ω PO = 5W; RS = 10KΩ SVR Supply Voltage Rejection VS = 16.5V; R L = 8Ω; f = 100Hz R s = 10kΩ; Vr = 0.5Vrms T sd 0.5 30 39 kΩ 50 to 40,000 Hz 75 dB 40 1.7 2 3 40 Thermal shut-down Junction Temperature % % 41 dB 6 mV µV µV 86 dB 50 dB 150 °C MUTE FUNCTION Symbol Vm ATTm Parameter Test Condition Pin 4 DC Voltage Mute SW Open (play) Muting Attenuation f = 100Hz to 10kHz Min. 60 Typ. Max. Unit 6.4 V 65 dB 3/11 TDA7245 ELECTRICAL CHARACTERISTCS (Continued) STAND-BY FUNCTION Symbol Parameter Test Condition Min. Typ. Vst-by Pin 5 DC Voltage Mute SW Open (play) 6.4 Ist- by Pin 5 Current Mute SW Closed (st-by) 160 Stand-by Attenuation f = 100Hz to 10kHz ATT st-by Vt Id st-by Stand-by Threshold (pin 5) Stand-by Current 70 Max. Unit 280 µA V 90 dB 3.8 VS = 14V 1 V 3 mA Note (*): MUSIC POWER CONCEPT MUSIC POWER is ( according to the IEC clauses n.268-3 of Jan 83) the maximal power which the amplifier is capable of producing across the rated load resistance (regardless of non linearity) 1 sec after the application of a sinusoidal input signal of frequency 1KHz. According to this definition our method of measurement comprises the following steps: 1) Set the voltage supply at the maximum operating value -20% 2) Apply a input signal in the form of a 1KHz tone burst of 1 sec duration; the repetition period of the signal pulses is > 60 sec 3) The output voltage is measured 1 sec from the start of the pulse 4) Increase the input voltage until the output signal show a THD = 10% 5) The music power is then V2out/R1, where Vout is the output voltage measured in the condition of point 4) and R1 is the rated load impedance The target of this method is to avoid excessive dissipation in the amplifier. Figure 2: Schematic Diagram 4/11 TDA7245 Figure 3: P.C. Board and Components Layout of the Circuit of fig 2 (1:1 scale) APPLICATION SUGGESTIONS The recommended values of the external components are those shown on the application circuit of fig.1. Different values can be used. The following table can help the dsigner. Component Rec. Value R1 20KΩ St-By Biasing Purpose Incorrect St-By Function Larger than Rec. Value Smaller than Rec. Value Feedback Resistors Increase of Gain Decrease of Gain Decrease of Gain Increase of Gain Frequency Stability Danger of Oscillations Worse POP and Shorter Delay at St-By Insertion R2(*) 27KΩ R3(*) 270Ω R4 1Ω C1 22µF St-By Capacitor Longer ON/OFF Delay Time at St-By IN/OUT Worse POP and Shorter Delay at St-By insertion C2 47µF SVR Capacitor Worse Turn-On POP by VS and St-By Degradation of SVR C3 0.1µF Input Capacitance Higher Low Frequency Cut-off C4 2.2µF Inverting Input DC Decoupling Higher Low Frequency Cut-off C5 470µF Supply Voltage Danger of Oscillations C6 0.22µF Frequency Stability C7 1000µF Output DC Decoupling Danger of Oscillations Higher Low Frequency Cut-off (*) The value of closed loop gain (GV = 1 + R2/R3) must be higher than 25dB. 5/11 TDA7245 Figure 4: DC Output Voltage vs. Supply Voltage Figure 5: ID vs. Supply Voltage Figure 6: Output Power vs. Supply Voltage Figure 7: Output Power vs. Supply Voltage Figure 8: Output Power vs. Supply Voltage Figure 9: Distortion vs. Output Power 6/11 TDA7245 Figure 10: Distortion vs. Output Power Figure 11: Distortion vs. Output Power Figure 12: Supply Voltage Rejection vs. Frequency (play) Figure 13: Power Dissipation & Efficiency vs. Output Power Figure 14: Power Dissipation & Efficiency vs. Output Power Figure 15: Vpin5 (=Vpin4) vs. Supply Voltage 7/11 TDA7245 Figure 16: Ipin4 (muting) vs. Supply Voltage Figure 17: Ipin5 (St-By) vs. Supply Voltage Figure 18: Quiescent Current (St-By) vs. Supply Voltage Figure 19: Output Attenuation vs. Vpin5 Figure 20: Quiescent Current vs. Vpin5 MUTING / STAND- BY The muting function allows to inhibit the output signal through an external control signal. It can be used in many cases, when a temporary inhibition of the output signal is requested, for example: – in switch-on condition, to avoid preamplifier power-on transients – during switching at the input stages – during the receiver tuning. The stand-by function is very useful and permits a complete turn ON/OFF of the device through a low power signal, which can be provided by a µP. 8/11 TDA7245 THERMAL SHUTDOWN The presence of a thermal limiting circuit offers the following advantages: 1)An overload on the output (even if it is permanent), or an above limit ambient temperature can be easily tolerated since the Tj cannot be higher than 150°C. 2)The heatsink can have a smaller factor of safety compared with that of a conventional circuit. There is no possibility of device damage due to high junction temperature. If for any reason, the junction temperature increase up to 150°C, the thermal shutdown simply reduces the power dissipation and the current consumption. The maximum allowable power dissipation depends upon the junction-ambient thermal resistance. Fig. 21 shows this dissipable power as a function of ambient temperature for different thermal resistance. MOUNTING INSTRUCTIONS The TDA7245 is assembled in the POWERDIP, in which 9 pins (from 10 to 18) are attached to the frame and remove the heat produced by the chip. Figure 22 shows a PC Board copper area used as a Heatsink (l = 65mm). The Thermal Resistance Junction-Ambient is 35°C. Figure 22: Example of Heatsink using PC Board Copper (l = 65mm) Figure 21: Maximum Allowable Power Dissipation vs. Ambient Temperature 9/11 TDA7245 POWERDIP 18 (9+9) PACKAGE MECHANICAL DATA mm DIM. MIN. a1 0.51 B 0.85 b b1 TYP. MAX. MIN. TYP. MAX. 0.020 1.40 0.033 0.50 0.38 0.055 0.020 0.50 D 0.015 0.020 24.80 0.976 E 8.80 0.346 e 2.54 0.100 e3 20.32 0.800 F 7.10 0.280 I 5.10 0.201 L Z 10/11 inch 3.30 0.130 2.54 0.100 TDA7245 Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specification mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. SGSTHOMSON Microelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of SGS-THOMSON Microelectronics. 1996 SGS-THOMSON Microelectronics – Printed in Italy – All Rights Reserved SGS-THOMSON Microelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A. 11/11