TDA7492P 25-watt + 25-watt dual BTL class-D audio amplifier Features ■ 25 W + 25 W continuous output power at THD = 10% with VCC = 20 V and RL = 8 Ω ■ Wide-range single-supply operation (8 - 26 V) ■ High efficiency (η = 90%) ■ Four selectable, fixed gain settings of nominally 21.6 dB, 27.6 dB, 31.1 dB and 33.6 dB ■ Differential inputs minimize common-mode noise ■ Standby and mute features ■ Short-circuit protection ■ Thermal overload protection ■ Externally synchronizable ■ ECOPACK®, environmentally-friendly package Table 1. PowerSSO-36 with exposed pad down Description The TDA7492P is a dual BTL class-D audio amplifier with single power supply, designed for LCD TVs and monitors. Thanks to the high efficiency and exposed-paddown (EPD) package no heatsink is required. Device summary Order code Operating temp. range Package Packaging TDA7492P -40 to 85 °C PowerSSO-36 EPD Tube TDA7492P13TR -40 to 85 °C PowerSSO-36 EPD Tape and reel September 2011 Doc ID 15068 Rev 5 1/26 www.st.com 1 Contents TDA7492P Contents 1 Device block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3 4 2.1 Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2.2 Pin list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Electrical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 3.1 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 3.2 Thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 3.3 Electrical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Characterization curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 4.1 Characterizations for 6 Ω loads with 18 V . . . . . . . . . . . . . . . . . . . . . . . . 10 4.2 Characterizations for 8 Ω loads with 20 V . . . . . . . . . . . . . . . . . . . . . . . . 13 5 Applications circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 6 Applications information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 6.1 Mode selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 6.2 Gain setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 6.3 Input resistance and capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 6.4 Internal and external clocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 6.4.1 Master mode (internal clock) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 6.4.2 Slave mode (external clock) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 6.5 Output low-pass filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 6.6 Protection functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 6.7 Diagnostic output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 7 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 8 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 2/26 Doc ID 15068 Rev 5 TDA7492P List of tables List of tables Table 1. Table 2. Table 3. Table 4. Table 5. Table 6. Table 7. Table 8. Table 9. Table 10. Device summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Pin description list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Thermal data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Electrical specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Mode settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Gain settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 How to set up SYNCLK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 PowerSSO-36 EPD dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Doc ID 15068 Rev 5 3/26 List of figures TDA7492P List of figures Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. Figure 7. Figure 8. Figure 9. Figure 10. Figure 11. Figure 12. Figure 13. Figure 14. Figure 15. Figure 16. Figure 17. Figure 18. Figure 19. Figure 20. Figure 21. Figure 22. Figure 23. Figure 24. Figure 25. Figure 26. Figure 27. Figure 28. 4/26 Internal block diagram (showing one channel only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Pin connections (top view, PCB view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Output power vs. supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 THD at 1 kHz vs. output power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 THD at 100 Hz vs. output power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 THD at 1 W vs. frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Frequency response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Crosstalk vs frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 FFT 0 dB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 FFT -60 dB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Output power vs supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 THD at 1 kHz vs output power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 THD at 100 Hz vs output power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 THD at 1 W vs frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Frequency response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Crosstalk vs frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 FFT 0 dB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 FFT -60 dB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Test board (SZ-LAB-TDA7492P) layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Applications circuit for class-D amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Standby and mute circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Turn-on/off sequence for minimizing speaker “pop” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Device input circuit and frequency response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Master and slave connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Typical LC filter for a 8-Ω speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Typical LC filter for a 4-Ω speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Behavior of pin DIAG for various protection conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 PowerSSO-36 EPD outline drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Doc ID 15068 Rev 5 TDA7492P 1 Device block diagram Device block diagram Figure 1 shows the block diagram of one of the two identical channels of the TDA7492P. Figure 1. Internal block diagram (showing one channel only) Doc ID 15068 Rev 5 5/26 Pin description TDA7492P 2 Pin description 2.1 Pinout Figure 2. 6/26 Pin connections (top view, PCB view) SUB_GND 1 36 VSS OUTPB 2 35 SVCC OUTPB 3 34 VREF PGNDB 4 33 INNB PGNDB 5 32 INPB PVCCB 6 31 GAIN1 PVCCB 7 30 GAIN0 OUTNB 8 29 SVR OUTNB 9 28 DIAG OUTNA 10 27 SGND OUTNA 11 26 VDDS PVCCA 12 25 SYNCLK PVCCA 13 24 ROSC PGNDA 14 23 INNA PGNDA 15 22 INPA OUTPA 16 21 MUTE OUTPA 17 20 STBY PGND 18 19 VDDPW Exposed pad down (Connect to ground) Doc ID 15068 Rev 5 TDA7492P 2.2 Pin description Pin list Table 2. Pin description list Number Name Type Description 1 SUB_GND PWR Connect to the frame 2,3 OUTPB O Positive PWM for right channel 4,5 PGNDB PWR Power stage ground for right channel 6,7 PVCCB PWR Power supply for right channel 8,9 OUTNB O Negative PWM output for right channel 10,11 OUTNA O Negative PWM output for left channel 12,13 PVCCA PWR Power supply for left channel 14,15 PGNDA PWR Power stage ground for left channel 16,17 OUTPA O Positive PWM output for left channel 18 PGND PWR Power stage ground 19 VDDPW O 3.3-V (nominal) regulator output referred to ground for power stage 20 STBY I Standby mode control 21 MUTE I Mute mode control 22 INPA I Positive differential input of left channel 23 INNA I Negative differential input of left channel 24 ROSC O Master oscillator frequency-setting pin 25 SYNCLK I/O Clock in/out for external oscillator 26 VDDS O 3.3-V (nominal) regulator output referred to ground for signal blocks 27 SGND PWR Signal ground 28 DIAG O Open-drain diagnostic output 29 SVR O Supply voltage rejection 30 GAIN0 I Gain setting input 1 31 GAIN1 I Gain setting input 2 32 INPB I Positive differential input of right channel 33 INNB I Negative differential input of right channel 34 VREF O Half VDDS (nominal) referred to ground 35 SVCC PWR Signal power supply 36 VSS O 3.3-V (nominal) regulator output referred to power supply - EP PWR Exposed pad for connection to ground plane as heatsink Doc ID 15068 Rev 5 7/26 Electrical specifications TDA7492P 3 Electrical specifications 3.1 Absolute maximum ratings Table 3. Absolute maximum ratings Symbol 3.2 Parameter Value Unit VCCMAX DC supply voltage for pins PVCCA, PVCCB, SVCC 30 V VI Voltage limits for input pins STANDBY, MUTE, INNA, INPA, INNB, INPB, GAIN0, GAIN1 -0.3 to 3.6 V Top Operating temperature -40 to 85 °C Tj Junction temperature -40 to 150 °C Tstg Storage temperature -40 to 150 °C Thermal data Table 4. Thermal data Symbol Parameter Rth j-case Thermal resistance, junction to case Rth j-amb Min - Thermal resistance, junction to ambient Typ 2 - 24 (1) Max Unit 3 °C/W - °C/W 1. FR4 with vias to copper area of 9 cm2 3.3 Electrical specifications Unless otherwise stated, the results in Table 5 below are given for the conditions: VCC = 20 V, RL (load) = 8 Ω, ROSC = R3 = 39 kΩ, C8 = 100 nF, f = 1 kHz, GV = 21.6 dB, and Tamb = 25 °C. Table 5. Symbol 8/26 Electrical specifications Parameter Condition Min Typ Max Unit VCC Supply voltage for pins PVCCA, PVCCB, SVCC - 8 - 26 V Iq Total quiescent - - 26 35 mA IqSTBY Quiescent current in standby - - 2.5 5.0 µA Play mode - - ±100 mV VOS Output offset voltage Mute mode - - ±60 mV IOCP Overcurrent protection threshold RL = 0 Ω 3.8 4.2 - A TjSD Junction temperature at thermal shutdown - - 150 - °C Ri Input resistance Differential input 48 60 - kΩ Doc ID 15068 Rev 5 TDA7492P Electrical specifications Table 5. Electrical specifications (continued) Symbol Parameter Condition Min Typ Max Unit VOVP Overvoltage protection threshold - 28 29 - V VUVP Undervoltage protection threshold - - - 7 V High side - 0.2 - RdsON Power transistor on resistance Low side - 0.2 - THD = 10% - 25 - Po Output power THD = 1% - 20 - 9.5 - Output power VCC = 12 V, THD = 10% - Po VCC = 12 V, THD = 1% - 7.2 - PD Power dissipated by device Po = 25 W + 25 W, THD = 10% - 5.0 - W η Efficiency Po = 10 W + 10 W 80 90 - % THD Total harmonic distortion Po = 1 W - 0.1 0.4 % GAIN0 = L, GAIN1 = L 20.6 21.6 22.6 GAIN0 = L, GAIN1 = H 26.6 27.6 28.6 GAIN0 = H, GAIN1 = L 30.1 31.1 32.1 GAIN0 = H, GAIN1 = H 32.6 33.6 34.6 GV Ω W W Closed-loop gain dB ΔGV Gain matching - - - ±1 dB CT Cross talk f = 1 kHz - 50 - dB 20 - Total input noise A Curve, GV = 20 dB - eN f = 22 Hz to 22 kHz - 25 35 µV SVRR Supply voltage rejection ratio fr = 100 Hz, Vr = 0.5 V, CSVR = 10 µF 40 50 - dB Tr, Tf Rise and fall times - - 50 - ns fSW Switching frequency Internal oscillator 290 310 330 kHz 250 - 400 250 - 400 2.3 - - - - 0.8 60 80 - fSWR Output switching frequency range VinH Digital input high (H) VinL Digital input low (L) AMUTE Mute attenuation With internal oscillator With external oscillator (1) (2) kHz VMUTE = 1 V V dB 1. fSW = 106 / ((16 * ROSC + 182) * 4) kHz, fSYNCLK = 2 * fSW with R3 = 39 kΩ, see Figure 20. 2. fSW = fSYNCLK / 2 with the frequency of the external oscillator. Doc ID 15068 Rev 5 9/26 Characterization curves 4 TDA7492P Characterization curves The following characterizations were made using the SZ-LAB-TDA7492P demo board. The layout is shown in Figure 19 on page 16. The LC filter for the 6 Ω load used 22 µH and 220 nF components, whilst that for the 8 Ω load used 33 µH and 220 nF. 4.1 Characterizations for 6 Ω loads with 18 V Figure 3. Output power vs. supply voltage 28 26 Vcc = 8 to 18 V, 24 RL = 6 Ω, 22 Rosc = 39 kΩ, Cosc = 100 nF, 20 f = 1 kHz, Gv = 30 dB, Tamb = 25r C Specification limit: Output power (W) Test conditions: THD = 10% 18 16 14 THD = 1% 12 10 8 Typical: 6 Vcc =18 V, RL = 6 Ω 4 Po = 25 W @THD = 10% 2 0 Po = 20 W @THD = 1% 8 9 10 11 12 13 14 15 16 17 18 Supply voltage (V) Figure 4. THD at 1 kHz vs. output power 10 5 Test conditions: Vcc = 18 V, THD (%) RL = 6 Ω, 2 Rosc = 39 kΩ, Cosc = 100 nF, 1 f = 1 kHz, 0.5 Gv = 30 dB, Tamb = 25r C 0.2 0.1 0.05 Specification limit: Typical: 0.02 Po = 25 W @THD = 10% 0.01 0.005 200m 500m 1 2 Output power (W) 10/26 Doc ID 15068 Rev 5 5 10 20 30 TDA7492P Characterization curves Figure 5. THD at 100 Hz vs. output power 10 Test conditions: Vcc = 18 V, 5 THD (%) RL = 6 Ω, 2 Rosc = 39 kΩ, Cosc = 100 nF, 1 f = 100 Hz, 0.5 Gv = 30 dB, Tamb = 25r C 0.2 0.1 0.05 Specification limit: 0.02 Typical: 0.01 Po = 25 W @THD = 10% 0.005 200m 500m 1 2 5 10 2k 5k 20 30 2XWSXWSRZHU: Figure 6. THD at 1 W vs. frequency 0.5 Test conditions: Vcc = 18 V, THD (%) RL = 6 Ω, 0.2 Rosc = 39 kΩ, Cosc = 100 nF, f = 1 kHz, 0.1 Gv = 30 dB, Po = 1 W 0.05 Tamb = 25r C 0.02 0.01 Specification limit: Typical: THD < 0.4% 0.005 20 50 100 200 500 1k 10k 20k Frequency (Hz) Figure 7. Frequency response +2 Test conditions: Vcc = 18 V, RL = 6 Ω, Ampl Rosc = 39 kΩ, Cosc = 100 nF, (dB) +1 -0 f = 1 kHz, Gv = 30 dB, -1 Po = 1 W Tamb = 25r C -2 -3 Specification limit: Max: -4 +/-3 dB @20 Hz to 20 kHz -5 10 20 50 100 200 500 1k 2k 5k 10k 30k Frequency (Hz) Doc ID 15068 Rev 5 11/26 Characterization curves Figure 8. TDA7492P Crosstalk vs frequency -60 Test conditions: -65 Vcc = 18 V, Crosstalk RL = 6 Ω, (dB) -70 -75 Rosc = 39 kΩ, Cosc = 100 nF, f = 1 kHz, -80 Gv = 30 dB, -85 Po = 1 W -90 Tamb = 25r C -95 -100 -105 Specification limit: -110 Typical: -115 > 50 dB @f = 1 kHz -120 20 50 100 200 500 1k 2k 5k 10k 20k Frequency (Hz) Figure 9. FFT 0 dB +10 Test conditions: +0 FFT -10 (dB) -20 Vcc = 18 V, RL = 6 Ω, -30 Rosc = 39 kΩ, Cosc = 100 nF, -40 f = 1 kHz, -50 Gv = 30 dB, -60 Po = 1 W -70 Tamb = 25r C -80 -90 -100 -110 Specification limit: -120 Typical: -130 > 60 dB for the harmonic frequency -140 -150 20 50 100 200 500 1k 2k 5k 10k Frequency (Hz) Figure 10. FFT -60 dB +0 -10 Test conditions: Vcc = 18 V, FFT -20 RL = 6 Ω, (dB) -30 Rosc = 39 kΩ, Cosc = 100 nF, -40 f = 1 kHz, -50 Gv = 30 dB, -60 Po = -60 dB @1 W = 0 dB -70 Tamb = 25r C -80 -90 -100 -110 Specification limit: -120 Typical: -130 > 90dB for the harmonic frequency -140 -150 20 50 100 200 500 1k Frequency (Hz) 12/26 Doc ID 15068 Rev 5 2k 5k 10k 20k 20k TDA7492P Characterizations for 8 Ω loads with 20 V Figure 11. Output power vs supply voltage 28 Test conditions: 26 Vcc = 8 to 20 V, 24 RL = 8 Ω, Rosc = 39 kΩ, Cosc = 100 nF, f = 1 kHz, Gv = 30 dB, Tamb = 25r C Output power (W) 4.2 Characterization curves 22 20 THD = 10% 18 16 14 12 THD = 1% 10 Specification limit: 8 Typical: 6 Vs = 20 V, RL = 8 Ω 4 Po = 25 W @THD = 10% 2 8 Po = 20 W @THD = 1% 9 10 11 12 13 14 15 16 17 18 19 20 Supply voltage (V) Figure 12. THD at 1 kHz vs output power 10 Test conditions: Vcc = 20 V, RL = 8 Ω, Rosc = 39 kΩ, Cosc = 100 nF, 5 THD (%) 2 1 f = 1 kHz, 0.5 Gv = 30 dB, Tamb = 25r C 0.2 0.1 0.05 Specification limit: Typical: 0.02 Po = 25 W @THD = 10% 0.01 0.005 100m 200m 500m 1 2 5 10 20 30 Output power (W) Doc ID 15068 Rev 5 13/26 Characterization curves TDA7492P Figure 13. THD at 100 Hz vs output power 10 Test conditions: Vcc = 20 V, 5 THD (%) RL = 8 Ω, 2 Rosc = 39 kΩ, Cosc = 100 nF, 1 f = 100 Hz, 0.5 Gv = 30 dB, Tamb = 25r C 0.2 0.1 0.05 Specification limit: 0.02 Typical: 0.01 Po = 25 W @THD = 10% 0.005 100m 200m 500m 1 2 5 10 20 30 Output power (W) Figure 14. THD at 1 W vs frequency 0.5 Test conditions: Vcc = 20 V, RL = 8 Ω, Rosc = 39 kΩ, Cosc = 100 nF, 0.2 THD (%) f = 1 kHz, 0.1 Gv = 30 dB, Po = 1 W 0.05 Tamb = 25r C 0.02 Specification Limit: 0.01 Typical: THD < 0.4% 0.005 20 50 100 200 500 1k 2k 5k 10k 20k Frequency (Hz) Figure 15. Frequency response +2 Test conditions: Vcc = 20 V, RL = 8 Ω, Rosc = 39 kΩ, Cosc = 100 nF, f = 1 kHz, +1 Ampl (dB) -0 Gv = 30 dB, -1 Po = 1 W Tamb = 25r C -2 -3 Specification limit: Max: -4 +/-3 dB @20 Hz to 20 kHz -5 10 20 50 100 200 500 1k Frequency (Hz) 14/26 Doc ID 15068 Rev 5 2k 5k 10k 20k 30k TDA7492P Characterization curves Figure 16. Crosstalk vs frequency -60 Test conditions: TTTTTTTTTTT TTTT T TTTTT -65 Vcc = 20 V, Crosstalk RL = 8 Ω, (dB) -70 -75 Rosc = 39 kΩ, Cosc = 100 nF, f = 1 kHz, -80 Gv = 30 dB, -85 Po = 1 W -90 Tamb = 25r C -95 -100 -105 Specification limit: -110 Typical: -115 > 50 dB @f = 1 kHz -120 20 50 100 200 500 1k 2k 5k 10k 20k 2k 5k 10k 20k 5k 10k 20k Frequency (Hz) Figure 17. FFT 0 dB +10 Test conditions: +0 Vcc = 20 V, FFT RL = 8 Ω (dB) -10 -20 Rosc = 39 kΩ, Cosc = 100 nF, -30 f = 1 kHz, -40 -50 Gv = 30 dB, -60 Po = 1 W -70 Tamb = 25r C -80 -90 -100 -110 Specification limit: -120 Typical: -130 > 60 dB for the harmonic frequency -140 -150 20 50 100 200 500 1k Frequency (Hz) Figure 18. FFT -60 dB +0 Test conditions: Vcc = 20 V, RL = 8 Ω, Rosc = 39 kΩ, Cosc = 100 nF, -10 FFT (dB) -20 -30 -40 f = 1 kHz, -50 Gv = 30 dB, -60 Po = -60 dB (1 W = 0 dB) -70 Tamb = 25r C -80 -90 -100 Specification limit: Typical: > 90 dB for the harmonic frequency -110 -120 -130 -140 -150 20 50 100 200 500 1k 2k Frequency (Hz) Doc ID 15068 Rev 5 15/26 Characterization curves TDA7492P 2. Test Board Figure 19. Test board (SZ-LAB-TDA7492P) layout 16/26 Doc ID 15068 Rev 5 Applications circuit TDA7492P 5 Figure 20. Applications circuit for class-D amplifier & Q) & Q) 6*1' & Q) & Q) 6*1' Jumper settings for gain: Q) 0V:0V 0 V : 3.3 V Doc ID 15068 Rev 5 31.1 dB 3.3 V : 3.3 V 33.6 dB 5 )RU 6LQJOH(QGHG ',$* & 5 Q) - Play - & & 9''6 Q) Q) ',$* 39&&$ & / 526& *$,1 9''6 *$,1 - 6*1' 6LQJOH(QGHG - Q) & 966 / 2873% X+ 39&&% 39&&% ,13% ,11% & & Q) 9 6*1' 6 087( 9 6*1' & 6*1' 6*1' 5 N 5 9&& ,1 /&= N 5 & Q) *1' N 6*1' 6*1' 6*1' 6*1' 6*1' 932:(56833/< 6*1' & & 3*1'% 2871% 2871% 9&& *1' - Q) 2875 2875 Q) & & S) Q) / X+ 95() 695 087( & X) 9 67%< & X) 9 & X) 9 6*1' 7'$36OXJGRZQ &/$66'$03/,),(5 & X) 9 6*1' /&),/7(5&20321(17 LC filter components /RDG Load && //// C20,C26 L1,L2,L3,L4 RKP 4Ω 15 µHX+ 470 Q) nF RKP 6Ω 22 µHX+ 220 Q) nF RKP 8Ω 33 µHX+ 220 Q) nF 16 Ω RKP 68 µHX+ 220 Q) nF 17/26 Applications circuit & X) 6*1' ,& Q) Q) 5 5 N 6 67%< 287 Q) & 5 6*1' & Q) X) 9 2873% 3*1'% 287/ ,& 69&& & - 287/ Q) X+ TDA7492P 7'$3 & S) 2871$ 6<1&/. . Standby 3.3 V : 3.3 V & Q) 6*1' 3*1' ,1/ ,QSXW Mute 5 9''3: 6<1&/. - )RU 3.3 V : 0 V 5 39&&$ Switch settings for standby, mute and play: 0 V : 3.3 V 2871$ Q) ,15 Standby 3*1'$ 3*1'$ 6*1' ,15 0V:0V ,11$ & - ,1/ Mode 5 STBY : MUTE X+ 5 N ,QSXW 3.3 V : 0 V / 2873$ 6*1' 21.6 dB 27.6 dB 2873$ ,13$ 9''6 & GAIN0 : GAIN1 Nominal gain 68%B*1' Applications information TDA7492P 6 Applications information 6.1 Mode selection The three operating modes of the TDA7492P are set by the two inputs STBY (pin 20) and MUTE (pin 21). ● Standby mode: all circuits are turned off, very low current consumption. ● Mute mode: inputs are connected to ground and the positive and negative PWM outputs are at 50% duty cycle. ● Play mode: the amplifiers are active. The protection functions of the TDA7492P are enabled by pulling down the voltages of the STBY and MUTE inputs shown in Figure 21. The input current of the corresponding pins must be limited to 200 µA. Table 6. Mode settings Mode selection STBY MUTE L (1) Standby Mute H Play H X (don’t care) (1) L H 1. Drive levels defined in Table 5: Electrical specifications on page 8 Figure 21. Standby and mute circuits Standby STBY 3.3 V 0V R2 30 kΩ C7 2.2 µF R4 30 kΩ C15 2.2 µF Mute MUTE 3.3 V 0V TDA7492P Figure 22. Turn-on/off sequence for minimizing speaker “pop” VCC 0 t STBY 0 t MUTE 0 Input t 0 t Output 0 t Standby Mute Play Mute Standby Iq 0 18/26 t Doc ID 15068 Rev 5 TDA7492P 6.2 Applications information Gain setting The gain of the TDA7492P is set by the two inputs, GAIN0 (pin 30) and GAIN1 (pin31). Internally, the gain is set by changing the feedback resistors of the amplifier. Table 7. Gain settings GAIN0 6.3 GAIN1 Nominal gain, Gv (dB) 0 0 21.6 0 1 27.6 1 0 31.1 1 1 33.6 Input resistance and capacitance The input impedance is set by an internal resistor Ri = 60 kΩ (typical). An input capacitor (Ci) is required to couple the AC input signal. The equivalent circuit and frequency response of the input components are shown in Figure 23. For Ci = 470 nF the high-pass filter cutoff frequency is below 20 Hz: fc = 1 / (2 * π * Ri * Ci) Figure 23. Device input circuit and frequency response Rf Input signal Ci Input pin Ri Doc ID 15068 Rev 5 19/26 Applications information 6.4 TDA7492P Internal and external clocks The clock of the class-D amplifier can be generated internally or can be driven by an external source. If two or more class-D amplifiers are used in the same system, it is recommended that all devices operate at the same clock frequency. This can be implemented by using one TDA7492P as master clock, while the other devices are in slave mode (that is, externally clocked. The clock interconnect is via pin SYNCLK of each device. As explained below, SYNCLK is an output in master mode and an input in slave mode. 6.4.1 Master mode (internal clock) Using the internal oscillator, the output switching frequency, fSW, is controlled by the resistor, ROSC, connected to pin ROSC: fSW = 106 / ((16 * ROSC + 182) * 4) kHz where ROSC is in kΩ. In master mode, pin SYNCLK is used as a clock output pin, whose frequency is: fSYNCLK = 2 * fSW For master mode to operate correctly then resistor ROSC must be less than 60 kΩ as given below in Table 8. 6.4.2 Slave mode (external clock) In order to accept an external clock input the pin ROSC must be left open, that is, floating. This forces pin SYNCLK to be internally configured as an input as given in Table 8. The output switching frequency of the slave devices is: fSW = fSYNCLK / 2 s Table 8. How to set up SYNCLK Mode ROSC SYNCLK Master ROSC < 60 kΩ Output Slave Floating (not connected) Input Figure 24. Master and slave connection Master Slave TDA7492P ROSC TDA7492P SYNCLK Output Cosc 100 nF 20/26 Rosc 39 kΩ Doc ID 15068 Rev 5 SYNCLK Input ROSC TDA7492P 6.5 Applications information Output low-pass filter To avoid EMI problems, it may be necessary to use a low-pass filter before the speaker. The cutoff frequency should be larger than 22 kHz and much lower than the output switching frequency. It is necessary to choose the L-C component values depending on the loud speaker impedance. Some typical values, which give a cutoff frequency of 27 kHz, are shown in Figure 25 and Figure 26 below. Figure 25. Typical LC filter for a 8-Ω speaker Figure 26. Typical LC filter for a 4-Ω speaker Doc ID 15068 Rev 5 21/26 Applications information 6.6 TDA7492P Protection functions The TDA7492P is fully protected against overvoltages, undervoltages, overcurrents and thermal overloads as explained here. Overvoltage protection (OVP) If the supply voltage exceeds the value for VOVP given in Table 5: Electrical specifications on page 8 the overvoltage protection is activated which forces the outputs to the high-impedance state. When the supply voltage drops to below the threshold value the device restarts. Undervoltage protection (UVP) If the supply voltage drops below the value for VUVP given in Table 5: Electrical specifications on page 8 the undervoltage protection is activated which forces the outputs to the high-impedance state. When the supply voltage recovers the device restarts. Overcurrent protection (OCP) If the output current exceeds the value for IOCP given in Table 5: Electrical specifications on page 8 the overcurrent protection is activated which forces the outputs to the high-impedance state. Periodically, the device attempts to restart. If the overcurrent condition is still present then the OCP remains active. The restart time, TOC, is determined by the R-C components connected to pin STBY. Thermal protection (OTP) If the junction temperature, Tj, reaches 145 °C (nominally), the device goes to mute mode and the positive and negative PWM outputs are forced to 50% duty cycle. If the junction temperature reaches the value for Tj given in Table 5: Electrical specifications on page 8 the device shuts down and the output is forced to the high-impedance state. When the device cools sufficiently the device restarts. 6.7 Diagnostic output The output pin DIAG is an open-drain transistor. When the protection is activated it is in the high-impedance state. The pin can be connected to a power supply (<26 V) by a pull-up resistor whose value is limited by the maximum sinking current (200 µA) of the pin. Figure 27. Behavior of pin DIAG for various protection conditions VDD TDA7492P R1 DIAG Protection logic VDD Restart Restart Overcurrent protection 22/26 OV, UV, OT protection Doc ID 15068 Rev 5 TDA7492P 7 Package mechanical data Package mechanical data The TDA7492P comes in a 36-pin PowerSSO package with exposed pad down. Figure 28 below shows the package outline and Table 9 gives the dimensions. Table 9. PowerSSO-36 EPD dimensions Dimensions in mm Dimensions in inches Symbol Min Typ Max Min Typ Max A 2.15 - 2.45 0.085 - 0.096 A2 2.15 - 2.35 0.085 - 0.093 a1 0 - 0.10 0 - 0.004 b 0.18 - 0.36 0.007 - 0.014 c 0.23 - 0.32 0.009 - 0.013 D 10.10 - 10.50 0.398 - 0.413 E 7.40 - 7.60 0.291 - 0.299 e - 0.5 - - 0.020 - e3 - 8.5 - - 0.335 - F - 2.3 - - 0.091 - G - - 0.10 - - 0.004 H 10.10 - 10.50 0.398 - 0.413 h - - 0.40 - - 0.016 k 0 - 8 degrees 0 - 8 degrees L 0.60 - 1.00 0.024 - 0.039 M - 4.30 - - 0.169 - N - - 10 degrees - - 10 degrees O - 1.20 - - 0.047 - Q - 0.80 - - 0.031 - S - 2.90 - - 0.114 - T - 3.65 - - 0.144 - U - 1.00 - - 0.039 - X 4.10 - 4.70 0.161 - 0.185 Y 4.90 - 7.10 0.193 - 0.280 In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark. Doc ID 15068 Rev 5 23/26 h x 45° Package mechanical data 24/26 Figure 28. PowerSSO-36 EPD outline drawing Doc ID 15068 Rev 5 TDA7492P TDA7492P 8 Revision history Revision history Table 10. Document revision history Date Revision Changes 30-Sep-2008 1 Initial release. 11-May-2009 2 Updated supply operating range to 8 V - 26 V on page 1 Changed C1 to C8 at beginning of Section 3.3 on page 8 Updated Table 5: Electrical specifications on page 8 for VCC min, VOS min/max and added new parameter VUV Updated Figure 20: Applications circuit for class-D amplifier on page 17 Inserted brackets in equation in Table 5 footnote and in Section 6.4.1 on page 20 Updated values in UVP and OCP in Section 6.6 on page 22 Updated voltage to “<26 V” in Section 6.7 on page 22 Updated max dimensions for A and A2 in Table 9: PowerSSO-36 EPD dimensions on page 23. 02-Sep-2009 3 Updated value for GV at head of Section 3.3 on page 8 Updated package Y (Min) dimension in Table 9 on page 23. 19-Jan-2011 4 Updated operating temperature range Updated datasheet presentation. 12-Sep-2011 5 Updated OUTNA in Table 2: Pin description list Doc ID 15068 Rev 5 25/26 TDA7492P Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY TWO AUTHORIZED ST REPRESENTATIVES, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2011 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 26/26 Doc ID 15068 Rev 5