TI THS3061DGNR

THS3061
THS3062
www.ti.com
SLOS394B – JULY 2002 – REVISED NOVEMBER 2009
LOW-DISTORTION, HIGH SLEW RATE, CURRENT-FEEDBACK AMPLIFIERS
Check for Samples: THS3061 THS3062
FEATURES
1
•
•
•
•
•
•
23
Unity Gain Bandwidth: 300 MHz
0.1-dB Bandwidth: 120 MHz (G = 2)
High Slew Rate: 7000 V/μs
HD3 at 10 MHz: –81 dBc (G = 2, RL = 150 Ω)
High Output Current: ±145 mA into 50 Ω
Power-Supply Voltage Range: ±5 V to ±15 V
APPLICATIONS
•
•
•
•
•
High-Speed Signal Processing
Test and Measurement Systems
VDSL Line Driver
High-Voltage ADC Preamplifier
Video Line Driver
The THS3061 and THS3062 provide well-regulated
ac performance characteristics with power supplies
ranging from ±5-V operation up to ±15-V supplies.
Most notably, the 0.1-dB flat bandwidth is exceedingly
high, reaching beyond 100 MHz, and the THS306x
has less than 0.3 dB of peaking in the frequency
response when configured in unity gain. The
unity-gain bandwidth of 300 MHz provides excellent
distortion characteristics at 10 MHz. The flexibility of
the current-feedback design allows a 220-MHz, –3-dB
bandwidth in a gain of 10, indicating excellent
performance even at high gains.
The THS306x consumes 8.3 mA per-channel
quiescent current at room temperature, and has the
capability of producing up to ±145 mA of output
current. The THS3061 is packaged in an 8-pin SOIC
and an 8-pin MSOP with PowerPAD™. The THS3062
is available in an 8-pin SOIC with PowerPAD and an
8-pin MSP with PowerPAD.
DESCRIPTION
The THS3061 (single) and THS3062 (dual) are
high-voltage, high slew-rate current feedback
amplifiers utilizing Texas Instruments' BICOM-1
process. Designed for low-distortion with a high slew
rate of 7000 V/μs, the THS306x amplifiers are ideally
suited for applications requiring large, linear output
signals such as video line drivers and VDSL line
drivers.
space
RELATED DEVICES AND DESCRIPTIONS
DEVICE
THS3001
Low Distortion
Current-Feedback Amplifier
THS3112
Dual Current-Feedback
Amplifier With 175 mA Drive
THS3122
Dual Current-Feedback
Amplifier With 350 mA Drive
OPA691
Wideband Current-Feedback
Amplifier with 350 mA Drive
SLEW RATE
vs
OUTPUT STEP
HARMONIC DISTORTION
vs
FREQUENCY
8000
–20
G=5
VCC = ±15
Rf = 375 Ω
TA = 25°C
6000
G=1
–30
Harmonic Distortion – dB
7000
SR – Slew Rate – V/ µ s
DESCRIPTION
5000
VCC = ±15
4000
3000
2000
–40
–50
VCC = ±15 V
VCC = ±5 V
RL = 1 kΩ
Rf = 750 Ω
VO = 2VPP
–60
2nd HD
–70
–80
3rd HD
1000
–90
0
0
5
10
15
Output Step – VPP
20
25
–100
100 k
1M
10 M
f – Frequency – Hz
100 M
1
2
3
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PowerPAD is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2002–2009, Texas Instruments Incorporated
THS3061
THS3062
SLOS394B – JULY 2002 – REVISED NOVEMBER 2009
www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
ABSOLUTE MAXIMUM RATINGS
Over operating free-air temperature range unless otherwise noted. (1)
VS
Supply voltage
VI
Input voltage
IO
Output current
VID
Differential input voltage
±16.5 V
±VS
200 mA
±3 V
Continuous power dissipation
TJ
TJ
(2)
Tstg
(1)
(2)
See Dissipation Ratings Table
Maximum junction temperature
+150°C
Maximum junction temperature, continuous operation, long term reliability
+125°C
Storage temperature range
–65°C to +150°C
The absolute maximum ratings under any condition is limited by the constraints of the silicon process. Stresses above these ratings may
cause permanent damage. Exposure to absolute maximum conditions for extended periods may degrade device reliability. These are
stress ratings only, and functional operation of the device at these or any other conditions beyond those specified is not implied.
The maximum junction temperature for continuous operation is limited by package constraints. Operation above this temperature may
result in reduced reliability and/or lifetime of the device.
PACKAGE DISSIPATION RATINGS
(1)
(2)
(3)
POWER RATING
(TJ = +125°C) (2)
PACKAGE
θJC
(°C/W)
θJA
(°C/W) (1)
TA ≤ +25°C
TA = +85°C
D (8 pin)
38.3
97.5
1.02 W
410 mW
DDA (8 pin)
(3)
9.2
45.8
2.18 W
873 mW
DGN (8 pin)
(3)
4.7
58.4
1.71 W
680 mW
This data was taken using the JEDEC High-K test PCB.
This data was taken using 2 oz. trace and copper pad that is soldered directly to a 3 in x 3 in PCB.
The THS306x may incorporate a PowerPAD on the underside of the chip. This acts as a heatsink and must be connected to a thermally
dissipative plane for proper power dissipation. Failure to do so may result in exceeding the maximum junction temperature which could
permanently damage the device. See TI technical brief SLMA002 for more information about utilizing the PowerPAD thermally enhanced
package.
RECOMMENDED OPERATING CONDITIONS
Supply voltage
2
Submit Documentation Feedback
MIN
MAX
Dual supply
±5
±15
Single supply
10
30
UNIT
V
Copyright © 2002–2009, Texas Instruments Incorporated
Product Folder Link(s): THS3061 THS3062
THS3061
THS3062
www.ti.com
SLOS394B – JULY 2002 – REVISED NOVEMBER 2009
ORDERING INFORMATION (1)
PART NUMBER
PACKAGE TYPE
PACKAGE MARKING
SOIC-8
—
MSOP-8-PP (2)
BIB
SOIC-8
—
SOIC-8-PP (2)
—
MSOP-8-PP (2)
BIC
TRANSPORT MEDIA, QUANTITY
Single
THS3061D
THS3061DR
THS3061DGN
THS3061DGNR
Rails, 75
Tape and Reel, 2500
Rails, 80
Tape and Reel, 2500
Dual
THS3062D
THS3062DR
THS3062DDA
THS3062DDAR
THS3062DGN
THS3062DGNR
(1)
(2)
Rails, 75
Tape and Reel, 2500
Rails, 75
Tape and Reel, 2500
Rails, 80
Tape and Reel, 2500
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
web site at www.ti.com.
The PowerPAD is electrically isolated from all other pins.
PIN ASSIGNMENTS
TOP VIEW
D, DGN
TOP VIEW
D, DDA, DGN
THS3061
NC
VIN −
VIN +
VS−
1
8
2
7
3
6
4
5
THS3062
NC
VS+
VOUT
NC
1VOUT
1VIN −
1VIN +
VS−
1
8
2
7
3
6
4
5
VS+
2VOUT
2VIN −
2VIN+
NC − No internal connection
PARAMETER MEASUREMENT INFORMATION
Rg
Rg
Rf
Rf
VI
_
_
VI
+
50 Ω
RT
VO
RL
RL
Figure 1. Noninverting Test Circuit
VO
+
Figure 2. Inverting Test Circuit
Copyright © 2002–2009, Texas Instruments Incorporated
Product Folder Link(s): THS3061 THS3062
Submit Documentation Feedback
3
THS3061
THS3062
SLOS394B – JULY 2002 – REVISED NOVEMBER 2009
www.ti.com
ELECTRICAL CHARACTERISTICS
At VS = ±15 V: Rf = 560 Ω, RL = 150 Ω, and G = 2, unless otherwise noted.
THS3061, THS3062
TYP
PARAMETER
OVER TEMPERATURE
TEST CONDITIONS
+25°C
+25°C
0°C to
+70°C
–40°C
to
+85°C
UNITS
MIN/
TYP/
MAX
MHz
Typ
AC PERFORMANCE
Small-signal bandwidth
(VO = 100 mVPP,
Peaking < 0.3 dB)
G = 1, Rf = 750Ω
300
G = 2, Rf = 560 Ω
275
G = 5, Rf = 357 Ω
260
G = 10, Rf = 200 Ω
220
Bandwidth for 0.1-dB flatness
G = 2, VO = 100mVPP
120
MHz
Typ
Peaking at a gain of 1
VO = 100 mVPP
0.3
dB
Typ
Large-signal bandwidth
G = 2, VO = 4 VPP
120
MHz
Typ
G = 5, 20 V-Step
7000
G = 2, 10 V-Step
5700
V/μs
Typ
1
ns
Typ
30
ns
Typ
125
ns
Typ
dBc
Typ
dBc
Typ
Slew rate (25% to 75% level)
Rise and fall time
Settling
time to
0.1%
0.01%
G = 2, VO = 10 V-Step
G = –2, VO = 2 V-Step
Harmonic distortion
2nd order harmonic
G = 2, f = 10 MHz,
VO = 2 VPP
3rd order harmonic
RL = 150 Ω
–78
RL = 1 kΩ
–73
RL = 150 Ω
–81
RL = 1 kΩ
–82
3rd order intermodulation distortion
G = 2, fc = 10 MHz,
VO = 2 VPP(envelope) Δf = 200 kHz
–93
dBc
Typ
Input voltage noise
f > 10 kHz
2.6
nV/√Hz
Typ
20
pA/√Hz
Typ
36
pA/√Hz
Typ
Input current noise (noninverting)
Input current noise (inverting)
Differential gain (NTSC, PAL)
Differential phase (NTSC, PAL)
f > 10 kHz
G = 2, RL = 150 Ω
0.02%
Typ
0.01°
Typ
DC PERFORMANCE
Open-loop transimpedance gain
VO = 0 V, RL = 1 kΩ
Input offset voltage
1
0.7
0.6
0.6
MΩ
Min
±0.7
±3.5
±4.4
±4.5
mV
Max
±10
±10
μV/°C
Typ
±2.0
±20
±32
±35
μA
Max
±25
±30
nA/°C
Typ
±38
±40
A
Max
±45
±50
nA/°C
Typ
V
Min
Average offset voltage drift
Input bias current (inverting)
Average bias current drift (–)
VCM = 0 V
Input bias current (noninverting)
±6.0
±25
Average bias current drift (+)
INPUT
Common-mode input range
Common-mode rejection ratio
Input resistance
Input capacitance
4
Submit Documentation Feedback
±13.9
±13.1
±13.1
±13.1
VCM = ±0.5 V
72
60
58
58
dB
Min
Noninverting
518
kΩ
Typ
Inverting
71
Ω
Typ
Noninverting
1
pF
Typ
Copyright © 2002–2009, Texas Instruments Incorporated
Product Folder Link(s): THS3061 THS3062
THS3061
THS3062
www.ti.com
SLOS394B – JULY 2002 – REVISED NOVEMBER 2009
ELECTRICAL CHARACTERISTICS (continued)
At VS = ±15 V: Rf = 560 Ω, RL = 150 Ω, and G = 2, unless otherwise noted.
THS3061, THS3062
TYP
PARAMETER
OVER TEMPERATURE
TEST CONDITIONS
+25°C
+25°C
0°C to
+70°C
–40°C
to
+85°C
±13.7
±13.4
±13.4
±13.3
±13
±12.6
±12.4
±12.3
UNITS
MIN/
TYP/
MAX
V
Min
OUTPUT
Voltage output swing
RL = 1 kΩ
RL = 150 Ω
Current output, sourcing
RL = 50 Ω
145
140
135
130
mA
Min
Current output, sinking
RL = 50 Ω
–145
–140
–135
–130
mA
Min
0.1
Ω
Typ
±15
V
Typ
POWER SUPPLY
Closed-loop output impedance
G = 1, f = 1 MHz
Specified operating voltage
Maximum operating voltage
±16.5
±16.5
±16.5
V
Max
Maximum quiescent current/channel
8.3
10
11.7
12
mA
Max
Minimum quiescent current/channel
8.3
6.1
6
6
mA
Min
Power-supply rejection (+PSRR)
VS+ = 14.50 V to 15.50 V
76
65
63
63
dB
Min
Power-supply rejection (–PSRR)
VS– = –14.50 V to –15.50 V
74
65
63
63
dB
Min
Copyright © 2002–2009, Texas Instruments Incorporated
Product Folder Link(s): THS3061 THS3062
Submit Documentation Feedback
5
THS3061
THS3062
SLOS394B – JULY 2002 – REVISED NOVEMBER 2009
www.ti.com
ELECTRICAL CHARACTERISTICS
At VS = ±5 V: Rf = 560 Ω, RL = 150 Ω , and G = 2, unless otherwise noted.
THS3061, THS3062
TYP
PARAMETER
OVER TEMPERATURE
TEST CONDITIONS
+25°C
+25°C
0°C to
+70°C
–40°C
to
+85°C
UNITS
MIN/
TYP/
MAX
MHz
Typ
AC PERFORMANCE
Small-signal bandwidth
(VO = 100 mVPP, peaking < 0.3 dB)
G = 1, Rf = 750 Ω
275
G = 2, Rf = 560 Ω
250
G = 5, Rf = 383 Ω
230
G = 10, Rf = 200 Ω
210
Bandwidth for 0.1-dB flatness
G = 2, VO = 100 mVPP
100
MHz
Typ
Peaking at a gain of 1
VO = 100 mVPP
< 0.3
dB
Typ
Large-signal bandwidth
G = 2, VO = 4 VPP
100
MHz
Typ
G = 1, 5-V Step, Rf = 750 Ω
2700
G = 5, 5-V Step, Rf = 357 Ω
1300
V/μs
Typ
ns
Typ
ns
Typ
dBc
Typ
dBc
Typ
Slew rate (25% to 75% level)
Rise and fall time
0.1%
Settling
time to
0.01%
G = 2, VO = 5-V Step
2
20
G = –2, VO = 2-V Step
160
Harmonic distortion
2nd order harmonic
G = 2, f = 10 MHz,
VO = 2 VPP
3rd order harmonic
RL = 150 Ω
–76
RL = 1 kΩ
–70
RL = 150 Ω
–79
RL = 1 kΩ
–77
3rd order intermodulation distortion
G = 2, fc = 10 MHz,
VO = 2 VPP(envelope)
Δf = 200 kHz
–91
dBc
Typ
Input voltage noise
f > 10 kHz
2.6
nV/√Hz
Typ
20
pA/√Hz
Typ
36
pA/√Hz
Typ
Input current noise (noninverting)
Input current noise (inverting)
Differential gain (NTSC, PAL)
Differential phase (NTSC, PAL)
f > 10 kHz
G = 2, RL = 150 Ω
0.025%
Typ
0.01°
Typ
DC PERFORMANCE
Open-loop transimpedance gain
VO = 0 V, RL = 1 kΩ
Input offset voltage
0.8
0.6
0.5
0.5
±0.3
±3.5
±4.4
±9
Average offset voltage drift
Input bias current (inverting)
Average bias current drift (–)
±2.0
±20
±6.0
±25
VCM = 0 V
Input bias current (noninverting)
Average bias current drift (+)
MΩ
Min
±4.5
mV
Max
±9
μV/°C
Typ
±32
±35
μA
Max
±20
±25
nA/°C
Typ
±38
±40
μA
Max
±30
±35
nA/°C
Typ
Min
INPUT
Common-mode input range
Common-mode rejection ratio
Input resistance
Input capacitance
±3.9
±3.1
±3.1
±3.1
V
VCM = ±0.5 V
70
60
58
58
dB
Min
Noninverting
518
kΩ
Typ
Inverting
71
Ω
Typ
Noninverting
1
pF
Typ
V
Min
OUTPUT
Voltage output swing
6
Submit Documentation Feedback
RL = 1 kΩ
±4.1
±3.8
±3.8
±3.7
RL = 150 Ω
±4.0
±3.6
±3.6
±3.5
Copyright © 2002–2009, Texas Instruments Incorporated
Product Folder Link(s): THS3061 THS3062
THS3061
THS3062
www.ti.com
SLOS394B – JULY 2002 – REVISED NOVEMBER 2009
ELECTRICAL CHARACTERISTICS (continued)
At VS = ±5 V: Rf = 560 Ω, RL = 150 Ω , and G = 2, unless otherwise noted.
THS3061, THS3062
TYP
PARAMETER
Current output, sourcing
Current output, sinking
Closed-loop output impedance
OVER TEMPERATURE
TEST CONDITIONS
RL = 50 Ω
G = 1, f = 1 MHz
+25°C
+25°C
0°C to
+70°C
–40°C
to
+85°C
UNITS
MIN/
TYP/
MAX
63
61
60
59
mA
Min
–63
–61
–60
–59
mA
Min
0.1
Ω
Typ
±5
V
Typ
POWER SUPPLY
Specified operating voltage
Minimum operating voltage
±4.5
±4.5
±4.5
V
Min
Maximum quiescent current
6.3
8.0
9.2
9.5
mA
Max
Minimum quiescent current
6.3
5.0
4.7
4.6
mA
Min
Power-supply rejection (+PSRR)
VS+ = 4.50 V to 5.50 V
73
65
63
63
dB
Min
Power-supply rejection (–PSRR)
VS– = –4.50 V to –5.50 V
75
65
63
63
dB
Min
space
space
space
TYPICAL CHARACTERISTICS
Table of Graphs
FIGURE
Small-signal frequency response
3-14
Large-signal frequency response
15, 16
Harmonic distortion
vs Frequency
17-23
Harmonic distortion
vs Output voltage
24-29
Output impedance
vs Frequency
30
Common-mode rejection ratio
vs Frequency
31
Input current noise
vs Frequency
32
Voltage noise density
vs Frequency
33
Power-supply rejection ratio
vs Frequency
34
Common-mode rejection ratio (DC)
vs Input common-mode range
Supply current
vs Power-supply voltage
36, 37
Slew rate
vs Output voltage
38, 39
Slew rate
vs Output step
Input offset voltage
vs Output voltage swing
Overdrive recovery time
35
40
41
42, 43
Differential gain
vs Number of 150-Ω loads
44, 45
Differential phase
vs Number of 150-Ω loads
46, 47
Copyright © 2002–2009, Texas Instruments Incorporated
Product Folder Link(s): THS3061 THS3062
Submit Documentation Feedback
7
THS3061
THS3062
SLOS394B – JULY 2002 – REVISED NOVEMBER 2009
www.ti.com
TYPICAL CHARACTERISTICS
SMALL-SIGNAL
FREQUENCY RESPONSE
SMALL-SIGNAL
FREQUENCY RESPONSE
2
1
0
-1
Rf 1 kΩ
Rf 750 Ω
-2
G=1
VCC = ±5 V
RL = 1 kΩ
VI = 100 mVPP
Rf 500 Ω
1
-1
Rf 1 kΩ
1M
10 M
100M
f - Frequency - Hz
-4
1G
100 k
1M
10 M
100 M
f - Frequency - Hz
SMALL-SIGNAL
FREQUENCY RESPONSE
SMALL-SIGNAL
FREQUENCY RESPONSE
SMALL-SIGNAL
FREQUENCY RESPONSE
9
10
G=1
VCC = ±15 V
RL = 1 kΩ
VI = 100 mVPP
Rf 357 Ω
Rf 500 Ω
6
4
Rf 1 kΩ
2
0
Rf 750 Ω
-3
G=2
VCC = ±15, ±5 V
RL = 150 Ω
VI = 100 mVPP
-2
-4
1M
10 M
100 M
f - Frequency - Hz
4
Rf 1 kΩ
G=2
VCC = ±15, ±5 V
RL = 1 kΩ
VI = 100 mVPP
2
1
Rf 560 Ω
0
100 k
1G
5
3
Rf 560 Ω
-4
1M
10 M
100 M
100 k
1G
1M
10 M
100 M
Figure 6.
Figure 7.
Figure 8.
SMALL-SIGNAL
FREQUENCY RESPONSE
SMALL-SIGNAL
FREQUENCY RESPONSE
SMALL-SIGNAL
FREQUENCY RESPONSE
18
Rf 200 Ω
16
14
12
100 k
1M
10 M
100 M
1G
f - Frequency - Hz
Figure 9.
Submit Documentation Feedback
16
Rf 560 Ω
10
Rf 383 Ω
Rf 200 Ω
14
12
Rf 560 Ω
10
18
G=5
VCC = ±15 V
RL = 1 kΩ
VI = 100 mVPP
Gain - dB
Gain - dB
G=5
VCC = ±5 V
RL = 150 Ω
VI = 100 mVPP
8
1G
f - Frequency - Hz
f - Frequency - Hz
18
8
Rf 357 Ω
7
6
Rf 1 kΩ
100 k
1G
8
8
Gain - dB
-1
16
1M
10 M
100 M
f - Frequency - Hz
Figure 5.
-2
Gain - dB
100 k
Figure 4.
0
8
1G
Figure 3.
2
1
Rf 750 Ω
-3
-4
100 k
Rf 1 kΩ
-1
Rf 750 Ω
-3
-4
Rf 500 Ω
-2
-2
-3
G=1
VCC = ±15 V
RL = 150 Ω
VI = 100 mVPP
0
0
Gain - dB
Gain - dB
1
Rf 500 Ω
Gain - dB
2
Gain - dB
2
3
G=1
VCC = ±5 V
RL = 150 Ω
VI = 100 mVPP
Gain - dB
3
SMALL-SIGNAL
FREQUENCY RESPONSE
G=5
VCC = ±15 V
RL = 150 Ω
VI = 100 mVPP
14
12
Rf 560 Ω
10
Rf 357 Ω
Rf 200 Ω
Rf 357 Ω
8
100 k
1M
10 M
100 M
1G
100 k
1M
10 M
f - Frequency - Hz
f - Frequency - Hz
Figure 10.
Figure 11.
100 M
1G
Copyright © 2002–2009, Texas Instruments Incorporated
Product Folder Link(s): THS3061 THS3062
THS3061
THS3062
www.ti.com
SLOS394B – JULY 2002 – REVISED NOVEMBER 2009
TYPICAL CHARACTERISTICS (continued)
SMALL-SIGNAL
FREQUENCY RESPONSE
SMALL-SIGNAL
FREQUENCY RESPONSE
3
3
G = -1
VCC =±5 V
RL = 150 Ω
VI = 100 mVPP
2
20
1
Gain - dB
19
18
G = 10
VCC =±5 V, ±15 V
RL = 150 Ω, 1 kΩ
VI = 100 mVPP,
17
Rf 332 Ω
1
0
-1
Rf 560 Ω
-2
Rf 511 Ω
1M
10 M
100 M
1G
Rf 560 Ω
Rf 475 Ω
1M
10 M
100 M
1G
100 k
1M
10 M
100 M
f - Frequency - Hz
f - Frequency - Hz
Figure 12.
Figure 13.
Figure 14.
LARGE-SIGNAL
FREQUENCY RESPONSE
LARGE-SIGNAL
FREQUENCY RESPONSE
THS3061
HARMONIC DISTORTION
vs FREQUENCY
9
8
Harmonic Distortion - dB
6
Gain - dB
Gain - dB
Rf = 1 KΩ
5
4
3
G=2
VCC = ±15 V
Rf = 560 Ω
VI = 2 VPP,
0
100 k
3
G=2
VCC = ±5 V
Rf = 604 Ω
RL = 150 Ω
RL = 1 kΩ
VI = 2 VPP,
10 M
100 M
100 k
1G
1M
-40
-50
-60
2nd HD
-70
-80
3rd HD
-90
2
1M
VCC = ±15 V
G=1
RL = 150 Ω
VO = 2 VPP
Rf = 750 Ω
-30
RL = 150 Ω
6
10 M
100 M
-100
1G
100 k
f - Frequency - Hz
f - Frequency - Hz
1M
10 M
Figure 16.
Figure 17.
THS3062
HARMONIC DISTORTION
vs FREQUENCY
HARMONIC DISTORTION
vs
FREQUENCY
HARMONIC DISTORTION
vs
FREQUENCY
-20
Harmonic Distortion - dB
-60
-30
2nd HD
-80
-40
-50
−60
VCC = ±5 V
G=1
RL = 150 Ω
VO = 2 VPP
Rf = 750 Ω
2nd HD
-60
-70
-80
-90
3rd HD
Harmonic Distortion − dB
VCC = ±15 V
G=1
RL = 150 Ω
VO = 2 VPP
Rf = 845 Ω
100 k
1M
10 M
f - Frequency - Hz
Figure 18.
−70
−80
2nd HD
−90
3rd HD
−100
−110
100 k
100 M
VCC = ±5 V, VCC = ±15 V
G=2
Rf = 560 Ω
RL = 150 Ω
VO = 1 VPP
3rd HD
-100
-100
100 M
f - Frequency - Hz
Figure 15.
-20
1G
-20
7
Harmonic Distortion - dB
-1
-4
100 k
f - Frequency - Hz
-40
0
-3
-4
100 k
Rf 332 Ω
-2
-3
16
G = -1
VCC =±15 V
RL = 150 Ω
VI = 100 mVPP
2
Gain - dB
21
Gain - dB
SMALL-SIGNAL
FREQUENCY RESPONSE
1M
10 M
f - Frequency - Hz
100 M
Figure 19.
Copyright © 2002–2009, Texas Instruments Incorporated
Product Folder Link(s): THS3061 THS3062
1M
10 M
100 M
f − Frequency − Hz
Figure 20.
Submit Documentation Feedback
9
THS3061
THS3062
SLOS394B – JULY 2002 – REVISED NOVEMBER 2009
www.ti.com
TYPICAL CHARACTERISTICS (continued)
HARMONIC DISTORTION
vs
FREQUENCY
-60
2nd HD
-70
-80
3rd HD
-60
-70
-80
3rd HD
1M
10 M
100 M
-100
-60
-70
-80
3rd HD
-90
1M
10 M
100 M
-100
100 k
Figure 23.
THS3061
HARMONIC DISTORTION
vs OUTPUT VOLTAGE
THS3061
HARMONIC DISTORTION
vs OUTPUT VOLTAGE
THS3061
HARMONIC DISTORTION
vs OUTPUT VOLTAGE
-60
2nd HD
-75
3rd HD
-80
-85
VCC = ±5 V
G=1
RL = 1 kΩ
Rf = 750 Ω
f = 10 MHz
-90
-95
-70
3rd HD
-75
-80
-85
VCC = ±15 V
G=1
RL = 1 kΩ
Rf = 750 Ω
f = 10 MHz
-90
-95
-100
2
3
4
5
6
3rd HD
-80
-85
-90
1
2
3
4
5
6
0
1
VO - Output Voltage - V
2
3
4
Figure 26.
THS3061
HARMONIC DISTORTION
vs OUTPUT VOLTAGE
HARMONIC DISTORTION
vs OUTPUT VOLTAGE
HARMONIC DISTORTION
vs OUTPUT VOLTAGE
-60
-60
-85
-70
-80
2nd HD 8 MHz
-90
3rd HD 1 MHz
VCC = ±15 V
G=2
Rf = 560 Ω
RL = 150 Ω
-100
-90
-95
3
4
5
VO - Output Voltage - V
Figure 27.
Submit Documentation Feedback
6
Harmonic Distortion - dBc
Harmonic Distortion - dBc
2nd HD 1 MHz
-80
2
6
3rd HD 8 MHz
2nd HD
3rd HD
1
5
VO - Output Voltage - V
Figure 25.
-75
0
-75
Figure 24.
VCC = ±5 V
G=1
RL = 150 Ω
f= 1 MHz
-70
2nd HD
-100
0
VO - Output Voltage - V
-65
-70
100 M
-95
-100
1
VCC = ±15 V
G=1
RL = 150 Ω
f= 1 MHz
Rf = 750 Ω
-65
Harmonic Distortion - dBc
Harmonic Distortion - dBc
-65
-70
-60
1M
10 M
f - Frequency - Hz
Figure 22.
-60
0
2nd HD
Figure 21.
2nd HD
-65
Harmonic Distortion - dBc
-50
f - Frequency - Hz
-60
Harmonic Distortion - dBc
-40
-90
f - Frequency - Hz
10
G=1
VCC = ±15 V
VCC = ±5 V
RL = 1 kΩ
Rf = 750 Ω
VO = 2VPP
-30
2nd HD
-90
-100
-20
VCC = ±15 V
G=2
Rf = 560 Ω
RL = 150 Ω
VO = 2VPP
-50
Harmonic Distortion - dB
-50
Harmonic Distortion - dB
-40
VCC = ±5 V
G=2
Rf = 560 Ω
RL = 150 Ω
VO = 2VPP
HARMONIC DISTORTION
vs
FREQUENCY
Harmonic Distortion - dB
-40
HARMONIC DISTORTION
vs
FREQUENCY
-110
0
2
4
6
8
10
2nd HD 1 MHz
-70
2nd HD f = 8 MHz
-80
3rd HD 8 MHz
-90
3rd HD f = 1 MHz
VCC = ±5 V
G=2
Rf = 560 Ω
RL = 150 Ω
-100
-110
0
12
VO - Output Voltage - V
1
2
3
4
5
6
VO - Output Voltage - V
Figure 28.
Figure 29.
Copyright © 2002–2009, Texas Instruments Incorporated
Product Folder Link(s): THS3061 THS3062
THS3061
THS3062
www.ti.com
SLOS394B – JULY 2002 – REVISED NOVEMBER 2009
TYPICAL CHARACTERISTICS (continued)
OUTPUT IMPEDANCE
vs
FREQUENCY
10
1
0.1
0.01
1M
10 M
100 M
THS3062
50
40
THS3061
20
10
In150
100
50
In+
1M
10 M
100 M
1G
10
100 k
Figure 31.
Figure 32.
VOLTAGE NOISE DENSITY
vs
FREQUENCY
POWER-SUPPLY REJECTION RATIO
vs FREQUENCY
COMMON-MODE REJECTION RATIO (DC)
vs
INPUT COMMON-MODE RANGE
25
VCC = ±5 V
20
15
10
5
VCC = ±15 V
10
100
1k
10 k
f - Frequency - Hz
70
CMMR - Common-Mode Rejection Ratio (DC) - dB
Figure 30.
0
VCC = ±15 V, ±5 V
G=2
Rf = 560 Ω
RL = 150 Ω
VO = 35 mVPP
60
50
40
PSRR+
30
20
10
PSRR0
-10
100 k
100 k
1M
10 M
100 M
f - Frequency - Hz
80
RL = 150 Ω
70
60
50
40
30
20
10
0
-15
-10
-5
0
5
Figure 34.
Figure 35.
THS3061
SUPPLY CURRENT vs
POWER-SUPPLY VOLTAGE
THS3062
SUPPLY CURRENT vs
POWER-SUPPLY VOLTAGE
SLEW RATE
vs
OUTPUT VOLTAGE
21
-40°C
6
4
2
0
2.5
85°C
G = -1
Rf = 475 Ω
RL = 150 Ω
TA = 25°C
18
3000
SR - Slew Rate - V/ µ s
8
ICC - Supply Current - mA
25°C
25°C
15
12
-40°C
9
6
6.5
8.5
10.5 12.5
4
Power Supply Voltage - V
Figure 36.
VCC = ±15
2000
1500
VCC = ±5
1000
0
0
14.5 16.5
2500
500
3
4.5
15
3500
24
85°C
10
10
Input Common-Mode Voltage Range - V
Figure 33.
12
I CC - Supply Current - mA
100
1k
10 k
f - Frequency - Hz
f - Frequency - Hz
PSRR - Power Supply Rejection Ratio - dBc
Hz
nV/
Vn - Voltage Noise Density -
30
200
0
0
100 k
1G
45
35
Hz
60
30
VCC = ±15 V,
VCC = ±5 V,
VCC = ±2.5 V,
250
pA
70
f - Frequency - Hz
40
300
G=2
VCC = ±15 V, ±5 V
RL = 150 Ω
Rf = 1 kΩ
80
I n - Input Current Noise -
G=2
Rf = 560 Ω
VCC = ±15 V
100 k
90
CMRR - Common-Mode Rejection Ratio - dB
ZO - Output Impedance - Ω
1000
100
INPUT CURRENT NOISE
vs
FREQUENCY
COMMON-MODE REJECTION RATIO
vs FREQUENCY
6
8
10
12
14
Power Supply Voltage - V
16
Figure 37.
Copyright © 2002–2009, Texas Instruments Incorporated
Product Folder Link(s): THS3061 THS3062
0
2
4
6
VO - Output Voltage - V
Figure 38.
Submit Documentation Feedback
11
THS3061
THS3062
SLOS394B – JULY 2002 – REVISED NOVEMBER 2009
www.ti.com
TYPICAL CHARACTERISTICS (continued)
SLEW RATE
vs
OUTPUT VOLTAGE
SLEW RATE
vs
OUTPUT STEP
8000
G=1
Rf = 750 Ω
RL = 150 Ω
TA = 25°C
SR - Slew Rate - V/ µ s
2000
VCC = ±15
1500
VCC = ±5
1000
500
6000
5000
VCC = ±15
4000
3000
2000
1000
1
2
3
4
VO - Output Voltage - V
5
0
6
5
Figure 39.
OVERDRIVE RECOVERY TIME
3
5
0
0
-1
-1
-2
G=2
VCC = ±5
Rf = 604 Ω
RL = 150 Ω
-2
-3
-3
0.5
0
1
1.5
VI - Input Voltage - V
1
VO - Output Voltage - V
0
0
-4
0.6
10
5
-5
-5
G=5
VCC = ±15
Rf = 560 Ω
RL = 150 Ω
0.5
0
1
1.5
0.5
VCC = ±5
0.4
0.3
0.2
-10
0.1
-15
0
2
VCC = ±15
1
2
3
Number of 150-Ω Loads
t - Time - µs
Figure 42.
Figure 43.
Figure 44.
DIFFERENTIAL GAIN
vs
NUMBER OF 150-Ω LOADS
DIFFERENTIAL PHASE
vs
NUMBER OF 150-Ω LOADS
DIFFERENTIAL PHASE
vs
NUMBER OF 150-Ω LOADS
0.07
G=2
Rf = 560 Ω
PAL Modulation
0.4
VCC = ±5
0.3
VCC = ±15
0.2
0.05
0.03
0.02
0.01
0
0
1
2
3
Number of 150-Ω Loads
Figure 45.
Submit Documentation Feedback
4
VCC = ±5
0.04
0.1
4
0.08
G=2
Rf = 560 Ω
NTSC Modulation
0.06
Differential Phase - Degree
0.5
20
G=2
Rf = 560 Ω
NTSC Modulation
t - Time - µs
0.6
Differential Gain - %
OVERDRIVE RECOVERY TIME
-1
2
-15 -10 -5
0
5
10 15
VO - Output Voltage Swing - V
DIFFERENTIAL GAIN
vs
NUMBER OF 150-Ω LOADS
1
-3
-1
Figure 41.
2
-4
85°C
Figure 40.
15
-2
25°C
-0.5
-20
Differential Phase - Degree
VI - Input Voltage - V
2
25
3
3
1
20
4
4
2
10
15
Output Step - VPP
Differential Gain - %
0
-40°C
-1.5
0
0
VO - Output Voltage - V
SR - Slew Rate - V/ µ s
2500
0
G=5
VCC = ±15
Rf = 375 Ω
TA = 25°C
7000
VIO- Input Offset Voltage - mV
3000
12
INPUT OFFSET VOLTAGE
vs
OUTPUT VOLTAGE SWING
G=2
Rf = 560 Ω
PAL Modulation
0.06
VCC = ±5
0.04
0.02
VCC = ±15
VCC = ±15
1
2
3
0
4
1
2
3
Number of 150-Ω Loads
Number of 150-Ω Loads
Figure 46.
Figure 47.
4
Copyright © 2002–2009, Texas Instruments Incorporated
Product Folder Link(s): THS3061 THS3062
THS3061
THS3062
www.ti.com
SLOS394B – JULY 2002 – REVISED NOVEMBER 2009
APPLICATION INFORMATION
INTRODUCTION
The THS306x is a high-speed operational amplifier
configured in a current-feedback architecture. The
device is built using Texas Instruments' BiCOM-I
process,
a
30-V,
dielectrically
isolated,
complementary bipolar process with NPN and PNP
transistors possessing fTs of several GHz. This
configuration
implements
an
exceptionally
high-performance amplifier that has a wide
bandwidth, high slew rate, fast settling time, and low
distortion.
MAXIMUM SLEW RATE FOR REPETITIVE
SIGNALS
The THS3061 and THS3062 are recommended for
high slew rate, pulsed applications where the internal
nodes of the amplifier have time to stabilize between
pulses.It is recommended to have at least a 20-ns
delay between pulses.
The THS3061 and THS3062 are not recommended
for applications with repetitive signals (sine, square,
sawtooth, or other types) that exceed 900 V/μs. Using
this device in these types of applications results in an
excessive current draw from the power supply and
possible device damage. For applications with a high
slew rate and repetitive signals, the THS3091 and
THS3095 (singles) or the THS3092 and THS3096
(duals) are recommended instead.
RECOMMENDED FEEDBACK AND GAIN
RESISTOR VALUES
As with all current-feedback amplifiers, the bandwidth
of the THS306x is an inversely proportional function
of the value of the feedback resistor. The
recommended resistors for optimum frequency
response are shown in Table 1. These should be
used as a starting point, and once optimum values
are found, 1% tolerance resistors should be used to
maintain frequency response characteristics. For
most applications, a feedback-resistor value of 750 Ω
is recommended—a good compromise between
bandwidth and phase margin that yields a very stable
amplifier.
As shown in Table 1, to maintain the highest
bandwidth with increasing gain, the feedback resistor
is reduced. The advantage of dropping the feedback
resistance (and the gain-resistor value) is that the
noise of the system is also reduced compared to no
reduction of these resistor values (see NOISE
CALCULATIONS). Thus, keeping the bandwidth as
high as possible maintains very good distortion
performance of the amplifier by keeping the excess
loop gain as high as possible.
Table 1. Recommended Resistor Values for
Optimum Frequency Response
GAIN
RF for VCC = ±15 V
RF for VCC = ±5 V
1
750 Ω
750 Ω
2, –1
560 Ω
560 Ω
5
357 Ω
383 Ω
10
200 Ω
200 Ω
Care must be taken to not set these values too low.
The amplifier's output must drive the feedback
resistance (and gain resistance), and this may place
a burden on the amplifier. The end result is that
distortion may actually increase due to the
low-impedance load presented to the amplifier. The
designer must carefully manage the amplifier
bandwidth and the associated loading effects for
optimum performance.
The THS3061/62 amplifiers exhibit very good
distortion performance and bandwidth, and can use
power supplies up to 15 V. The excellent
current-drive capability of up to 145 mA into a 50-Ω
load allows many versatile applications. One
application is driving a twisted pair line (that is, a
telephone line). Figure 48 shows a simple circuit for
driving a twisted pair differentially.
Copyright © 2002–2009, Texas Instruments Incorporated
Product Folder Link(s): THS3061 THS3062
Submit Documentation Feedback
13
THS3061
THS3062
SLOS394B – JULY 2002 – REVISED NOVEMBER 2009
www.ti.com
THS3062(a)
0.1 µF
en
Noiseless
+
_
eni
+
10 µF
IN+
eno
eRf
RS
+
_
VI+
eRs
RS
+12 V
Rf
RLine
2n2
499 Ω
0.1 µF
Telephone Line
210 Ω
Rg
RLine
THS3062(b)
VI–
Figure 49. Noise Model
RS
+
_
eRg
IN–
1:n
RLine
space
2n2
499 Ω
0.1 µF
10 µF
space
+
–12 V
space
Figure 48. Simple Line Driver With THS3062
Due to the high supply voltages and the large
current-drive capability, the power dissipation of the
amplifier must be carefully considered. To have as
much power dissipation as possible in a small
package, the THS3062 is available only in a MSOP-8
PowerPAD package (DGN), and an even lower
thermal-impedance SOIC-8 PowerPAD package
(DDA). The thermal impedance of a standard SOIC
package is too large to allow useful applications with
up to 30 V across the power-supply terminals with
this dual amplifier. But the THS3061 (a single
amplifier) can be used in the standard SOIC package.
Again, the amplifier power dissipation must be
carefully examined, or else the amplifiers could
overheat, severely degrading performance. See the
Power Dissipation and Thermal Considerations
section for more information on thermal management.
NOISE CALCULATIONS
Noise can cause errors on very small signals. This is
especially true for amplifying small signals coming
over a transmission line or an antenna. The noise
model for current-feedback amplifiers (CFB) is the
same as for voltage feedback amplifiers (VFB). The
only difference between the two is that CFB
amplifiers generally specify different current-noise
parameters for each input, while VFB amplifiers
usually only specify one noise-current parameter. The
noise model is shown in Figure 49. This model
includes all of the noise sources as follows:
• en = Amplifier internal voltage noise (nV/√Hz)
• IN+ = Noninverting current noise (pA/√Hz)
• IN– = Inverting current noise (pA/√Hz)
• eRx = Thermal voltage noise associated with each
resistor (eRx = 4 kTRx)
14
Submit Documentation Feedback
space
space
The total equivalent input noise density (eni) is
calculated by using the following equation:
e
ni
+
Ǹǒ
2
e nǓ ) IN )
ǒ
R
S
Ǔ
2
ǒ
) IN *
ǒR f ø RgǓǓ
2
ǒ
Ǔ
) 4 kTR s ) 4 kT R ø R g
f
where
k = Boltzmann’s constant = 1.380658 × 10–23
T = Temperature in degrees Kelvin (273 +°C)
Rf || Rg = Parallel resistance of Rf and Rg
To calculate the equivalent output noise of the
amplifier, multiply the equivalent input noise density
(eni) by the overall amplifier gain (AV).
e no + e
ǒ
Ǔ
R
A + e
1) f
ni V
ni
Rg
(Noninverting Case)
As the previous equations show, to keep noise at a
minimum, small value resistors should be used. As
the closed-loop gain is increased (by reducing RF and
RG), the input noise is reduced considerably because
of the parallel resistance term. This leads to the
general conclusion that the most dominant noise
sources are the source resistor (RS) and the internal
amplifier noise voltage (en). Because noise is
summed in a root-mean-squares method, noise
sources smaller than 25% of the largest noise source
can be effectively ignored. This can greatly simplify
the formula and make noise calculations much easier.
PCB LAYOUT TECHNIQUES
FOR OPTIMAL PERFORMANCE
Achieving optimum performance with high-frequency
devices in the THS306x family requires careful
attention to board layout, parasitic effects, and
external component types.
Recommendations to optimize performance include:
Copyright © 2002–2009, Texas Instruments Incorporated
Product Folder Link(s): THS3061 THS3062
THS3061
THS3062
www.ti.com
•
•
•
SLOS394B – JULY 2002 – REVISED NOVEMBER 2009
Minimize parasitic capacitance to any ac ground
for all signal I/O pins. Parasitic capacitance on the
output and input pins can cause instability. To
reduce unwanted capacitance, a window around
the signal I/O pins should be opened in all of the
ground and power planes around those pins.
Ground and power planes should be unbroken
elsewhere on the board.
Minimize the distance (< 0.25”) from the power
supply pins to high frequency 0.1-μF decoupling
capacitors. At the device pins, the ground and
power plane layout should not be in close
proximity to the signal I/O pins. Avoid narrow
power and ground traces to minimize inductance
between the pins and the decoupling capacitors.
The power supply connections should always be
decoupled with these capacitors. Larger (6.8 μF or
more) tantalum decoupling capacitors, effective at
lower frequencies, should also be used on the
main supply pins. These may be placed
somewhat farther from the device and may be
shared among several devices in the same area
of the printed circuit board (PCB). The primary
goal is to minimize the impedance in the
differential-current return paths. For driving
differential loads with the THS3062, adding a
capacitor between the power-supply pins
improves
2nd-order
harmonic-distortion
performance. This also minimizes the current loop
formed by the differential drive.
Careful selection and placement of external
components preserve the high frequency
performance of the THS306x family. Resistors
should be a very low reactance type.
Surface-mount resistors work best and allow a
tighter overall layout. Again, keep leads and PCB
trace lengths as short as possible. Never use
wirebound-type resistors in a high-frequency
application. Since the output pin and inverting
input pins are the most sensitive to parasitic
capacitance, always position the feedback and
series-output resistors, if any, as close as possible
to the inverting-input pins and output pins. Other
network components, such as input-termination
resistors, should be placed close to the
gain-setting resistors. Even with a low parasitic
capacitance shunting the external resistors,
excessively high resistor values can create
significant time constants that can degrade
performance.
Good
axial
metal-film
or
surface-mount resistors have approximately 0.2
pF in shunt with the resistor. For resistor values >
2.0 kΩ, this parasitic capacitance can add a pole
and/or a zero that can affect circuit operation.
Keep resistor values as low as possible,
consistent with load-driving considerations.
•
•
Connections to other wideband devices on the
board may be made with short direct traces or
through onboard transmission lines. For short
connections, consider the trace and the input to
the next device as a lumped capacitive load.
Relatively wide traces (50 mils to 100 mils) should
be used, preferably with ground and power planes
opened up around them. Estimate the total
capacitive load and determine if isolation resistors
on the outputs are necessary. Low parasitic
capacitive loads (< 4 pF) may not need an RS
since the THS306x family is nominally
compensated to operate with a 2-pF parasitic
load. Higher parasitic capacitive loads without an
RS are allowed as the signal gain increases
(increasing the unloaded phase margin). If a long
trace is required, and the 6-dB signal loss intrinsic
to a doubly-terminated transmission line is
acceptable, implement a matched-impedance
transmission line using microstrip or stripline
techniques (consult an ECL design handbook for
microstrip and stripline layout techniques).
A 50-Ω environment is not necessary onboard,
and in fact, a higher-impedance environment
improves
distortion
as
shown
in
the
distortion-versus-load plots. With a characteristic
board-trace impedance based on board material
and trace dimensions, a matching series resistor
is used in the trace from the output of the
THS306x, as well as a terminating shunt resistor
at the input of the destination device.
Remember also that the terminating impedance is
the parallel combination of the shunt resistor and
the input impedance of the destination device: this
total effective impedance should be set to match
the trace impedance. If the 6-dB attenuation of a
doubly-terminated
transmission
line
is
unacceptable,
a
long
trace
can
be
series-terminated at the source end only. Treat
the trace as a capacitive load in this case. This
does not preserve signal integrity as well as a
doubly-terminated line. If the input impedance of
the destination device is low, there is some signal
attenuation due to the voltage divider formed by
the series output into the terminating impedance.
Socketing a high speed part like the THS306x
family is not recommended. The additional lead
length and pin-to-pin capacitance introduced by
the socket can create an extremely troublesome
parasitic network that can make it almost
impossible to achieve a smooth, stable frequency
response. Best results are obtained by soldering
the THS306x family parts directly onto the board.
PowerPAD DESIGN CONSIDERATIONS
The
THS306x
family
is
available
in
a
thermally-enhanced PowerPAD family of packages.
These packages are constructed using a downset
Copyright © 2002–2009, Texas Instruments Incorporated
Product Folder Link(s): THS3061 THS3062
Submit Documentation Feedback
15
THS3061
THS3062
SLOS394B – JULY 2002 – REVISED NOVEMBER 2009
www.ti.com
leadframe upon which the die is mounted [see
Figure 50(a) and Figure 50(b)]. This arrangement
results in the lead frame being exposed as a thermal
pad on the underside of the package [see
Figure 50(c)]. Because this thermal pad has direct
thermal contact with the die, excellent thermal
performance can be achieved by providing a good
thermal path away from the thermal pad.
0.205
0.060
0.017
Pin 1
0.013
0.030
0.075
The PowerPAD package allows for both assembly
and thermal management in one manufacturing
operation. During the surface-mount solder operation
(when the leads are being soldered), the thermal pad
can also be soldered to a copper area underneath the
package. Through the use of thermal paths within this
copper area, heat can be conducted away from the
package into either a ground plane or other heat
dissipating device.
The PowerPAD package represents a breakthrough
in combining the small area and ease of assembly of
surface mount, compared with awkward mechanical
methods of heatsinking.
DIE
Side View (a)
Thermal
Pad
DIE
End View (b)
Bottom View (c)
Figure 50. Views of Thermally Enhanced Package
Although there are many ways to properly heatsink
the PowerPAD package, the following steps illustrate
the recommended approach.
PowerPAD PCB LAYOUT CONSIDERATIONS
1. Prepare the PCB with a top-side etch pattern as
shown in Figure 51. There should be etch for the
leads as well as etch for the thermal pad.
16
Submit Documentation Feedback
0.025 0.094
0.010
vias
0.035
0.040
Top View
Figure 51. DGN PowerPAD PCB Etch
and Via Pattern
2. Place five holes in the area of the thermal pad.
These holes should be 10 mils in diameter. Keep
them small so that solder wicking through the
holes is not a problem during reflow.
3. Additional vias may be placed anywhere along
the thermal plane outside of the thermal pad
area. This helps dissipate the heat generated by
the THS306x-family IC. These additional vias
may be larger than the 10-mil diameter vias
directly under the thermal pad. They can be
larger because they are not in the thermal pad
area to be soldered, so wicking is not a problem.
4. Connect all holes to the internal ground plane.
5. When connecting these holes to the ground
plane, do not use the typical web or spoke via
connection methodology. Web connections have
a high thermal resistance that is useful for
slowing the heat transfer during soldering
operations, making the soldering of vias that have
plane connections easier. In this application,
however, low thermal resistance is desired for the
most efficient heat transfer. Therefore, the holes
under the THS306x family PowerPAD package
should make their connection to the internal
ground plane with a complete connection around
the entire circumference of the plated-through
hole.
6. The top-side solder mask should leave the
terminals of the package and the thermal pad
area with its five holes exposed. The bottom-side
solder mask should cover the five holes of the
thermal pad area. This prevents solder from
being pulled away from the thermal pad area
during the reflow process.
7. Apply solder paste to the exposed thermal pad
area and all IC terminals.
8. With these preparatory steps in place, the IC is
simply placed in position and run through the
Copyright © 2002–2009, Texas Instruments Incorporated
Product Folder Link(s): THS3061 THS3062
THS3061
THS3062
www.ti.com
SLOS394B – JULY 2002 – REVISED NOVEMBER 2009
POWER DISSIPATION AND
THERMAL CONSIDERATIONS
To maintain maximum output capability, the THS360x
does not incorporate automatic thermal shutoff
protection. The designer must ensure that the design
does not violate the absolute maximum junction
temperature of the device. Failure may result if the
absolute maximum junction temperature of +150°C is
exceeded. For best performance, design for a
maximum junction temperature of +125°C. Between
+125°C and +150°C, damage does not occur, but the
performance of the amplifier begins to degrade.
The thermal characteristics of the device are dictated
by the package and the PC board. Maximum power
dissipation for a given package can be calculated
using Equation 1.
P Dmax +
Tmax * T A
q JA
where
PDmax is the maximum power dissipation in the amplifier (W).
Tmax is the absolute maximum junction temperature (°C).
TA is the ambient temperature (°C).
θJA = θJC + θCA
θJC is the thermal coefficient from the silicon junctions to the case (°C/W).
θCA is the thermal coefficient from the case to ambient air (°C/W).
(1)
For systems where heat dissipation is more critical,
the THS306x family of devices is offered in an 8-pin
MSOP with PowerPAD, and the THS3062 is available
in the SOIC-8 PowerPAD package offering even
better thermal performance. The thermal coefficients
for the PowerPAD packages are substantially
improved over traditional SOICs. Maximum power
dissipation levels are given in the graph for the
available packages. Data for the PowerPAD
packages assumes a board layout that follows the
PowerPAD layout guidelines referenced above and
detailed in the PowerPAD application note number
SLMA002. The following graph also illustrates the
effect of not soldering the PowerPAD to a PCB. The
thermal impedance increases substantially, which can
cause serious heat and performance issues. Always
be sure to solder the PowerPAD to the PCB for
optimum performance.
4
PD – Maximum Power Dissipation – W
solder reflow operation as any standard
surface-mount component. This results in a
properly-installed device.
TJ = 125°C
3.5
θJA = 45.8°C/W
3
θJA = 58.4°C/W
2.5
θJA = 98°C/W
2
1.5
1
0.5
θJA = 158°C/W
0
–40
–20 0
20
40
60
80
TA – Free-Air Temperature – °C
100
Results are With No Air Flow and PCB Size = 3”x3”
θJA = 45.8°C/W for 8-Pin SOIC w/PowerPad (DDA)
θJA = 58.4°C/W for 8-Pin MSOP w/PowerPad (DGN)
θJA = 98°C/W for 8-Pin SOIC High Test PCB (D)
θJA = 158°C/W for 8-Pin MSOP w/PowerPad w/o Solder
Figure 52. Maximum Power Dissipation
vs Ambient Temperature
When determining whether or not the device satisfies
the maximum power dissipation requirement, it is
important not only to consider quiescent power
dissipation, but also dynamic power dissipation.
Often, this is difficult to quantify because the signal
pattern is inconsistent, but an estimate of the RMS
power dissipation can provide visibility into a possible
problem.
DRIVING A CAPACITIVE LOAD
Driving capacitive loads with high-performance
amplifiers is not a problem as long as certain
precautions are taken. The first is to realize that the
THS306x has been internally compensated to
maximize its bandwidth and slew-rate performance.
When the amplifier is compensated in this manner,
capacitive loading directly on the output decreases
the device's phase margin, leading to high-frequency
ringing or oscillations. Therefore, for capacitive loads
of greater than 10 pF, it is recommended that a
resistor be placed in series with the output of the
amplifier as shown in Figure 53. A minimum value of
10 Ω works well for most applications. For example,
in 75-Ω transmission systems, setting the
series-resistor value to 75 Ω both isolates any
capacitive loading and provides the proper line
impedance matching at the source end.
Copyright © 2002–2009, Texas Instruments Incorporated
Product Folder Link(s): THS3061 THS3062
Submit Documentation Feedback
17
THS3061
THS3062
SLOS394B – JULY 2002 – REVISED NOVEMBER 2009
www.ti.com
Rf
Rg
Input
_
10 Ω
Output
THS306x
+
CLOAD
and should not be considered when using a
current-feedback amplifier. Because of this,
integrators and simple low-pass filters, which are
easily implemented on a VFB amplifier, must be
designed slightly differently. If filtering is required,
simply place an RC-filter at the noninverting terminal
of the operational-amplifier (see Figure 54).
Rg
Rf
f
Figure 53. Driving a Capacitive Load
V
–
VI
+
R1
VO
–3dB
O +
V
I
ǒ
+
1)
1
2pR1C1
Ǔǒ
R
f
Rg
Ǔ
1
1 ) sR1C1
C1
General Configurations
A common error for the first-time CFB-amplifier user
is creating a unity gain buffer amplifier by shorting the
output directly to the inverting input. In this
configuration, a CFB amplifier oscillates, and is not
recommended. The THS306x, like all CFB amplifiers,
must have a feedback resistor for stable operation.
Additionally, placing capacitors directly from the
output to the inverting input is not recommended,
because at high frequencies, a capacitor has a very
low impedance. This results in an unstable amplifier
18
Submit Documentation Feedback
Figure 54. Single-Pole Low-Pass Filter
Copyright © 2002–2009, Texas Instruments Incorporated
Product Folder Link(s): THS3061 THS3062
THS3061
THS3062
www.ti.com
SLOS394B – JULY 2002 – REVISED NOVEMBER 2009
If a multiple-pole filter is required, a Sallen-Key filter
can work very well with CFB amplifiers. This is
because the filtering elements are not in the negative
feedback loop and stability is not compromised.
Because of their high slew rates and high
bandwidths, CFB amplifiers can pass very accurate
signals and help minimize distortion. An example is
shown in Figure 55.
Rg
Rf
For Stable Operation:
–
THS306x
VO
+
R2
R1 || RA
≥
(
1+
VO ≅ VI
R1
R2
Rf
Rg
Rf
Rg
sR1C1
)
VI
C1
RA
C1
+
_
VI
R1
R1 = R2 = R
C1 = C2 = C
Q = Peaking Factor
(Butterworth Q = 0.707)
R2
f
C2
Rg
–3dB
Rg =
Rf
+
(
2–
Rf
1
Q
)
Figure 55. 2-Pole Low-Pass Sallen-Key Filter
There are two simple ways to create an integrator
with a CFB amplifier. The first, shown in Figure 56,
adds a resistor in series with the capacitor. This is
acceptable, because at high frequencies, the resistor
is dominant and the feedback impedance never drops
below the resistor value. The second, shown in
Figure 57, uses positive feedback to create the
integration. Caution is advised because oscillations
can occur due to the positive feedback.
The THS306x may also be employed as a very good
video-distribution amplifier. One characteristic of
distribution amplifiers is the fact that the differential
phase (dP) and the differential gain (dG) are
compromised as the number of lines increases and
the closed-loop gain increases. Be sure to use
termination resistors throughout the distribution
system to minimize reflections and capacitive loading.
Rg
Rf
–
75-Ω Transmission Line
VO1
75 Ω
75 Ω
THS306x
N Lines
75 Ω
VON
75 Ω
V
Rg
–
+
75 Ω
+
VI
C1
Rf
VI
Figure 57. Noninverting CFB Integrator
1
2pRC
VO
O +
VI
THS306x
ǒ
R
ȡS ) Rf1C1ȣ
Ǔȧ S ȧ
Ȣ
Ȥ
f
Rg
Figure 58. Video Distribution Amplifier
Application
Figure 56. Inverting CFB Integrator
Copyright © 2002–2009, Texas Instruments Incorporated
Product Folder Link(s): THS3061 THS3062
Submit Documentation Feedback
19
THS3061
THS3062
SLOS394B – JULY 2002 – REVISED NOVEMBER 2009
www.ti.com
REVISION HISTORY
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision A (October, 2002) to Revision B
Page
•
Updated document format to current standards ................................................................................................................... 1
•
Deleted lead temperature specification from Absolute Maximum Ratings table .................................................................. 2
•
Added Maximum Slew Rate for Repetitive Signals section ................................................................................................ 13
20
Submit Documentation Feedback
Copyright © 2002–2009, Texas Instruments Incorporated
Product Folder Link(s): THS3061 THS3062
PACKAGE OPTION ADDENDUM
www.ti.com
18-Oct-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
THS3061D
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
3061
THS3061DG4
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
3061
THS3061DGN
ACTIVE
MSOPPowerPAD
DGN
8
80
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
BIB
THS3061DGNG4
ACTIVE
MSOPPowerPAD
DGN
8
80
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
BIB
THS3061DGNR
ACTIVE
MSOPPowerPAD
DGN
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
BIB
THS3061DGNRG4
ACTIVE
MSOPPowerPAD
DGN
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
BIB
THS3061DR
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
3061
THS3061DRG4
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
3061
THS3062D
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
3062
THS3062DDA
ACTIVE SO PowerPAD
DDA
8
75
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 85
3062
THS3062DDAG3
ACTIVE SO PowerPAD
DDA
8
75
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 85
3062
THS3062DG4
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
3062
THS3062DGN
ACTIVE
MSOPPowerPAD
DGN
8
80
Green (RoHS
& no Sb/Br)
CU NIPDAU | Call TI
Level-1-260C-UNLIM
-40 to 85
BIC
THS3062DGNG4
ACTIVE
MSOPPowerPAD
DGN
8
80
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
BIC
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
18-Oct-2013
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
THS3061DGNR
MSOPPower
PAD
DGN
8
2500
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
THS3061DR
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
THS3061DGNR
MSOP-PowerPAD
DGN
8
2500
358.0
335.0
35.0
THS3061DR
SOIC
D
8
2500
367.0
367.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated