OPA875

OP
A8
OPA875
75
www.ti.com ............................................................................................................................................ SBOS340C – DECEMBER 2006 – REVISED AUGUST 2008
Single 2:1 High-Speed Video Multiplexer
FEATURES
DESCRIPTION
1
• 700MHz SMALL-SIGNAL BANDWIDTH
(AV = +2)
• 425MHz, 4VPP BANDWIDTH
• 0.1dB GAIN FLATNESS to 200MHz
• 4ns CHANNEL SWITCHING TIME
• LOW SWITCHING GLITCH: 40mVPP
• 3100V/µs SLEW RATE
• 0.025%/0.025° DIFFERENTIAL GAIN, PHASE
• HIGH GAIN ACCURACY: 2.0V/V ±0.4%
2
APPLICATIONS
•
•
•
•
•
System power may be reduced using the chip enable
feature for the OPA875. Taking the chip enable line
high powers down the OPA875 to less than 300µA
total supply current. Muxing multiple OPA875 outputs
together, then using the chip enable to select which
channels are active, increases the number of possible
inputs.
RGB SWITCHING
LCD PROJECTOR INPUT SELECT
WORKSTATION GRAPHICS
ADC INPUT MUX
DROP-IN UPGRADE TO LT1675-1
Where three channels are required, consider using
the OPA3875 for the same level of performance.
EN
Ch 0
75W
OPA875
(Patented)
The OPA875 offers a very wideband, single-channel
2:1 multiplexer in an SO-8 or a small MSOP-8
package. Using only 11mA, the OPA875 provides a
gain of +2 video amplifier channel with greater
than 425MHz large-signal bandwidth (4VPP). Gain
accuracy and switching glitch are improved over
earlier solutions using a new input stage switching
approach. This technique uses current steering as the
input switch while maintaining an overall closed-loop
design. With greater than 700MHz small-signal
bandwidth at a gain of 2, the OPA875 gives a typical
0.1dB gain flatness to greater than 200MHz.
75W
Out
OPA875 RELATED PRODUCTS
DESCRIPTION
Ch 1
75W
SEL
Channel Select
OPA3875
Triple-Channel OPA875
OPA692
225MHz Video Buffer
OPA693
700MHz Video Buffer
2:1 Video Multiplexer
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2006–2008, Texas Instruments Incorporated
OPA875
SBOS340C – DECEMBER 2006 – REVISED AUGUST 2008 ............................................................................................................................................ www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
ORDERING INFORMATION
PRODUCT
PACKAGELEAD
PACKAGE
DESIGNATOR
SPECIFIED
TEMPERATURE
RANGE
PACKAGE
MARKING
OPA875
SO-8
D
–40°C to +85°C
OPA875
OPA875
MSOP-8
DGK
–40°C to +85°C
BPL
ORDERING
NUMBER
TRANSPORT
MEDIA, QUANTITY
OPA875ID
Rails, 75
OPA875IDR
Tape and Reel, 2500
OPA875IDGKT
Tape and Reel, 250
OPA875IDGKR
Tape and Reel, 2500
ABSOLUTE MAXIMUM RATINGS (1)
Over operating temperature range, unless otherwise noted.
OPA875
Power Supply
UNIT
±6.5
Internal Power Dissipation
V
See Thermal Analysis
Input Voltage Range
Storage Temperature Range
±VS
V
–65 to +125
°C
Lead Temperature (soldering, 10s)
+260
°C
Operating Junction Temperature
+150
°C
Continuous Operating Junction Temperature
+140
°C
Human Body Model (HBM)
2000
V
Charged Device Model (CDM)
1500
V
Machine Model (MM)
200
V
ESD Rating:
(1)
Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may
degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond
those specified is not implied.
PIN CONFIGURATION
Table 1. TRUTH TABLE
OPA875
2
Top View
SELECT
ENABLE
VOUT
1
0
R0
0
0
R1
X
1
Off
MSOP, SO
OPA875
Channel 0 (V0)
1
8
+VS
GND
2
7
Chip Enable (EN)
Channel 1 (V1)
3
6
Output (VOUT)
-VS
4
5
Channel Select (SEL)
Submit Documentation Feedback
402W
402W
Copyright © 2006–2008, Texas Instruments Incorporated
Product Folder Link(s): OPA875
OPA875
www.ti.com ............................................................................................................................................ SBOS340C – DECEMBER 2006 – REVISED AUGUST 2008
ELECTRICAL CHARACTERISTICS: VS = ±5V
At G = +2 and RL = 150Ω, unless otherwise noted.
OPA875
MIN/MAX OVER
TEMPERATURE
TYP
PARAMETER
CONDITIONS
AC PERFORMANCE
+25°C
+25°C (2)
0°C to
+70°C (3)
–40°C to
+85°C (3)
UNITS
MIN/
MAX
TEST
LEVEL (1)
B
See Figure 1
Small-Signal Bandwidth
VO = 200mVPP, RL = 150Ω
700
525
515
505
MHz
min
Large-Signal Bandwidth
VO = 4VPP, RL = 150Ω
425
390
380
370
MHz
min
B
VO = 200mVPP
200
MHz
typ
C
Maximum Small-Signal Gain
VO = 200mVPP, RL = 150Ω, f = 5MHz
2.0
2.02
2.03
2.05
V/V
max
B
Minimum Small-Signal Gain
VO = 200mVPP, RL = 150Ω, f = 5MHz
2.0
1.98
1.97
1.95
V/V
min
B
10MHz, VO = 2VPP, RL = 150Ω
–66
–64
–63
–62
dBc
max
B
Input Voltage Noise
f > 100kHz
6.7
7.0
7.2
7.4
nV/√Hz
max
B
Input Current Noise
f > 100kHz
3.8
4.2
4.6
4.9
pA/√Hz
max
B
NTSC Differential Gain
RL = 150Ω
0.025
%
typ
C
NTSC Differential Phase
RL = 150Ω
0.025
C
Slew Rate
VO = ±2V
3100
VO = 0.5V Step
Bandwidth for 0.1dB Gain Flatness
SFDR
Rise Time and Fall Time
°
typ
V/µs
min
B
460
ps
typ
C
VO = 1.4V Step
600
ps
typ
C
RL = 150Ω
±0.05
±0.25
±0.3
±0.35
%
max
A
±3
±9
±10
±12
mV
max
A
2800
2700
2600
CHANNEL-TO-CHANNEL PERFORMANCE
Gain Match
Output Offset Voltage Mismatch
Crosstalk
f < 50MHz, RL = 150Ω
–65
dB
typ
C
RL = 150Ω
4
ns
typ
C
Turn On
9
ns
typ
C
Turn Off
60
ns
typ
C
SEL (Channel Select) Switching Glitch
Both Inputs to Ground, At Matched Load
40
mVPP
typ
C
EN (Chip-Select) Switching Glitch
Both Inputs to Ground, At Matched Load
30
mVPP
typ
C
50MHz, Chip Disabled (EN = High)
–70
dB
typ
C
CHANNEL AND CHIP-SELECT
PERFORMANCE
SEL (Channel Select) Switching Time
EN (Chip Select) Switching Time
Off Isolation
Maximum Logic 0
EN, A0, A1
0.8
0.8
0.8
V
max
A
Minimum Logic 1
EN, A0, A1
2.0
2.0
2.0
V
min
A
EN Logic Input Current
0V to 4.5V
25
35
45
50
µA
max
A
SEL Logic Input Current
0V to 4.5V
55
70
85
100
µA
max
A
RIN = 0Ω, G = +2V/V
±2.5
±14
±15.8
±17
mV
max
A
±50
±50
µV/°C
max
B
±19.5
±20.5
µA
max
A
±40
±40
nA/°C
max
B
1.5
1.6
%
max
A
DC PERFORMANCE
Output Offset Voltage
Average Output Offset Voltage Drift
Input Bias Current
±5
±18
Average Input Bias Current Drift
Gain Error (from 2V/V)
VO = ±2V
0.4
1.4
INPUT
Input Voltage Range
±2.8
V
min
C
Input Resistance
1.75
MΩ
typ
C
Channel Selected
0.9
pF
typ
C
Channel Deselected
0.9
pF
typ
C
Chip Disabled
0.9
pF
typ
C
Input Capacitance
(1)
(2)
(3)
Test levels: (A) 100% tested at +25°C. Over temperature limits set by characterization and simulation. (B) Limits set by characterization
and simulation. (C) Typical value only for information.
Junction temperature = ambient for +25°C tested specifications.
Junction temperature = ambient at low temperature limit; junction temperature = ambient +14°C at high temperature limit for over
temperature specifications.
Submit Documentation Feedback
Copyright © 2006–2008, Texas Instruments Incorporated
Product Folder Link(s): OPA875
3
OPA875
SBOS340C – DECEMBER 2006 – REVISED AUGUST 2008 ............................................................................................................................................ www.ti.com
ELECTRICAL CHARACTERISTICS: VS = ±5V (continued)
At G = +2 and RL = 150Ω, unless otherwise noted.
OPA875
MIN/MAX OVER
TEMPERATURE
TYP
PARAMETER
CONDITIONS
+25°C
+25°C (2)
0°C to
+70°C (3)
–40°C to
+85°C (3)
UNITS
MIN/
MAX
TEST
LEVEL (1)
A
OUTPUT
Output Voltage Range
Output Current
Output Resistance
Output Capacitance
±3.5
±3.4
±3.35
±3.3
V
min
VO = 0V, Linear Operation
±70
±50
±45
±40
mA
min
A
Chip enabled
0.3
Ω
typ
C
Chip Disabled, Maximum
800
912
915
918
Ω
max
A
Chip Disabled, Minimum
800
688
685
682
Ω
min
A
Chip Disabled
2
pF
typ
C
POWER SUPPLY
Specified Operating Voltage
V
typ
C
Minimum Operating Voltage
±5
±3.0
±3.0
±3.0
V
min
B
Maximum Operating Voltage
±6.0
±6.0
±6.0
V
max
A
Maximum Quiescent Current
Chip Selected, VS = ±5V
11
11.5
11.7
12
mA
max
A
Minimum Quiescent Current
Chip Selected, VS = ±5V
11
10
9.5
9
mA
min
A
Maximum Quiescent Current
Chip Deselected
300
500
550
600
µA
max
A
(+PSRR)
Input-Referred
56
50
48
47
dB
min
A
(–PSRR)
Input-Referred
55
51
49
48
dB
min
A
–40 to +85
°C
typ
C
Power-Supply Rejection Ratio
THERMAL CHARACTERISTICS
Specified Operating Range D Package
Thermal Resistance θJA
4
Junction-to-Ambient
D
SO-8
+100
°C/W
typ
C
DGK
MSOP-8
+140
°C/W
typ
C
Submit Documentation Feedback
Copyright © 2006–2008, Texas Instruments Incorporated
Product Folder Link(s): OPA875
OPA875
www.ti.com ............................................................................................................................................ SBOS340C – DECEMBER 2006 – REVISED AUGUST 2008
TYPICAL CHARACTERISTICS: VS = ±5V
At G = +2 and RL = 150Ω, unless otherwise noted.
LARGE-SIGNAL FREQUENCY RESPONSE
1
6
0.2
0
5
0.1
4
0
3
-0.1
2
-0.2
VO = 500mVPP
RL = 150W
G = +2V/V
1
-0.3
0
Normalized Gain (dB)
0.3
Normalized Gain Flatness (dB)
Gain (dB)
SMALL-SIGNAL FREQUENCY RESPONSE
7
10M
100M
-2
-3
5VPP
4VPP
-6
1G
0
200M
400M
0
2.0
-10
1.5
0.2
1.0
Small-Signal 0.4VPP
0.1
0.5
0
0
-0.1
-0.5
-0.2
-1.0
-0.3
-1.5
-0.4
-2.0
100MHz Square-Wave Input
-0.5
Input-Referred
BW = +5V
-20
Isolation (dB)
Large-Signal 4VPP
DISABLE FEEDTHROUGH vs FREQUENCY
2.5
Large-Signal Offset Voltage (V)
Small-Signal Offset Voltage (V)
0.3
1G
800M
Figure 2.
NONINVERTING PULSE RESPONSE
0.4
600M
Frequency (Hz)
Figure 1.
RL = 150W
G = +2V/V
1VPP
2VPP
Frequency (Hz)
0.5
500mVPP
-4
-5
-0.4
1M
-1
-30
-40
-50
-60
-70
-80
-90
-2.5
-100
1M
Time (1ns/div)
10M
100M
1G
Frequency (Hz)
Figure 3.
Figure 4.
RECOMMENDED RS vs CAPACITIVE LOAD
FREQUENCY RESPONSE vs CAPACITIVE LOAD
8
80
7
Gain to Capacitive Load (dB)
70
60
RS (W)
50
40
30
20
10
0.1dB Peaking Targeted
CL = 10pF
6
5
4
3
CL = 47pF
2
1
RS
0
(1)
CL
-1
1kW
CL = 22pF
75W
-2
0
CL = 100pF
x2
75W
NOTE: (1) 1kW is optional.
-3
1
10
100
1000
1M
10M
100M
400M
Frequency (Hz)
Capacitive Load (pF)
Figure 5.
Figure 6.
Submit Documentation Feedback
Copyright © 2006–2008, Texas Instruments Incorporated
Product Folder Link(s): OPA875
5
OPA875
SBOS340C – DECEMBER 2006 – REVISED AUGUST 2008 ............................................................................................................................................ www.ti.com
TYPICAL CHARACTERISTICS: VS = ±5V (continued)
At G = +2 and RL = 150Ω, unless otherwise noted.
HARMONIC DISTORTION vs LOAD RESISTANCE
HARMONIC DISTORTION vs SUPPLY VOLTAGE
-40
VO = 2VPP
f = 10MHz
-65
2nd-Harmonic
-70
-75
-80
3rd-Harmonic
-85
-50
-55
-60
-70
-75
-85
dBc = dB Below Carrier
-95
±2.5
±3.0
±3.5
±4.0
1k
Supply Voltage (±VS)
Figure 7.
Figure 8.
-60
-55
2nd-Harmonic
-60
-65
-70
-75
-80
3rd-Harmonic
-85
-90
-65
-70
2nd-Harmonic
-75
-80
-85
3rd-Harmonic
-90
-95
dBc = dB Below Carrier
10M
0.5
100M
2.5
3.5
4.5
5.5
Output Voltage Swing (VPP)
Figure 9.
Figure 10.
6.5 7.0
OUTPUT VOLTAGE AND CURRENT LIMITATIONS
5
-50
-60
1.5
Frequency (Hz)
TWO-TONE, 3RD-ORDER INTERMODULATION SPURIOUS
RL = 100W
Load Power at Matched 50W Load
dBc = dB Below Carrier
4
1W Internal
Power Limit
3
2
-70
VOUT (V)
Third-Order Spurious Level (dBc)
±6.0
-105
1M
50MHz
-80
20MHz
100W Load Line
1
25W Load Line
0
-1
-2
10MHz
50W Load Line
-3
-90
1W Internal
Power Limit
-4
-100
-6
-4
-2
0
2
4
6
8
10
-5
-200
-150
-100
-50
0
50
100
150
200
IO (mA)
Single-Tone Load Power (dBm)
Figure 11.
6
±5.5
RL = 150W
f = 10MHz
-100
dBc = dB Below Carrier
-95
±5.0
HARMONIC DISTORTION vs OUTPUT VOLTAGE
-55
Harmonic Distortion (dBc)
Harmonic Distortion (dBc)
-50
±4.5
Resistance (W)
VO = 2VPP
RL = 150W
-45
3rd-Harmonic
-80
HARMONIC DISTORTION vs FREQUENCY
-40
2nd-Harmonic
-65
-90
dBc = dB Below Carrier
-90
100
VO = 2VPP
RL = 150W
f = 10MHz
-45
Harmonic Distortion (dBc)
Harmonic Distortion (dBc)
-60
Figure 12.
Submit Documentation Feedback
Copyright © 2006–2008, Texas Instruments Incorporated
Product Folder Link(s): OPA875
OPA875
www.ti.com ............................................................................................................................................ SBOS340C – DECEMBER 2006 – REVISED AUGUST 2008
TYPICAL CHARACTERISTICS: VS = ±5V (continued)
At G = +2 and RL = 150Ω, unless otherwise noted.
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
-0.5
VSEL
RL = 150W
VIN_RI = 400MHz, 1VPP
VIN_RO = 0VDC
Output Voltage
VSEL
VIN_Ch0 = +0.5VDC
VIN_Ch1 = -0.5VDC
Time (5ns/div)
Figure 14.
Output (mV)
DISABLE/ENABLE TIME
Output Voltage (V)
CHANNEL SWITCHING GLITCH
20
At Matched Load
10
0
-10
7.5
5.0
VSEL
2.5
0
-2.5
1.5
1.0
0.5
0
-0.5
-1.0
-1.5
Output Voltage
VEN
Channel Select (V)
-20
VIN_Ch1 = 0V
VIN_Ch0 = 200MHz, 1VPP
Time (10ns/div)
Time (20ns/div)
Figure 15.
Figure 16.
DISABLE/ENABLE SWITCHING GLITCH
CHANNEL-TO-CHANNEL CROSSTALK
15
0
At Matched Load
-10
5
-20
0
-30
-5
-15
VEN
5.0
2.5
0
-2.5
Time (100ns/div)
Enable Voltage (V)
-10
Output (V)
Output (mV)
10
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
-0.5
Time (5ns/div)
Figure 13.
30
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
-0.5
Channel Select (V)
Output Voltage
1.5
1.0
0.5
0
-0.5
-1.0
-1.5
Enable Voltage (V)
Output Voltage (V)
CHANNEL-TO-CHANNEL SWITCHING TIME
Channel Select (V)
Output Voltage (V)
CHANNEL SWITCHING
1.5
1.0
0.5
0
-0.5
-1.0
-1.5
Input-Referred
-40
-50
Ch 0 Selected
Ch 1 Driven
-60
-70
-80
-90
Ch 1 Selected
Ch 0 Driven
-100
-110
1M
10M
100M
1G
Frequency (Hz)
Figure 17.
Figure 18.
Submit Documentation Feedback
Copyright © 2006–2008, Texas Instruments Incorporated
Product Folder Link(s): OPA875
7
OPA875
SBOS340C – DECEMBER 2006 – REVISED AUGUST 2008 ............................................................................................................................................ www.ti.com
TYPICAL CHARACTERISTICS: VS = ±5V (continued)
At G = +2 and RL = 150Ω, unless otherwise noted.
CLOSED-LOOP OUTPUT IMPEDANCE vs FREQUENCY
INPUT IMPEDANCE vs FREQUENCY
10M
Disabled
1k
1M
Input Impedance (W)
Output Impedance (W)
10k
100
10
100k
1
10k
1k
Enabled
0.1
100k
1M
10M
100M
100
100k
1G
1M
10M
Frequency (Hz)
Figure 19.
PSRR vs FREQUENCY
SUPPLY CURRENT vs TEMPERATURE
18
16
+PSRR
Supply Current (mA)
Power-Supply Rejection Ratio (dB)
-PSRR
50
40
30
20
10
14
12
10
8
6
4
2
1k
10k
100k
1M
10M
100M
1G
-50
75
IB
2.0
4
1.5
2
0
50
75
100
125
Voltage Noise (nV/ÖHz)
Current noise (pA/ÖHz)
6
25
125
INPUT VOLTAGE AND CURRENT NOISE
VOS
2.5
100
100
Input Bias Current (mA)
Output Offset Voltage (mV)
50
Figure 22.
1.0
10
Voltage Noise (6.7nV/ÖHz)
Input Current Noise (3.8pA/ÖHz)
1
10
100
1k
10k
100k
1M
10M
100M
Frequency (Hz)
Ambient Temperature (°C)
Figure 23.
8
25
Figure 21.
8
0
0
Ambient Temperature (°C)
TYPICAL DC DRIFT OVER TEMPERATURE
-25
-25
Frequency (Hz)
3.0
-50
1G
Figure 20.
60
0
100
100M
Frequency (Hz)
Figure 24.
Submit Documentation Feedback
Copyright © 2006–2008, Texas Instruments Incorporated
Product Folder Link(s): OPA875
OPA875
www.ti.com ............................................................................................................................................ SBOS340C – DECEMBER 2006 – REVISED AUGUST 2008
APPLICATIONS INFORMATION
1-BIT HIGH-SPEED PGA
TRANSMIT/RECEIVE SWITCH
The OPA875 can be used as a 1-bit, high-speed
programmable gain amplifier (PGA) when used in
conjunction with another amplifier. Figure 25 shows
the OPA695 used twice with one amplifier configured
in a unity-gain structure, and the other amplifier
configured in a gain of +8V/V.
The OPA875 can be used as a transmit/receive
switch in which the receive channel is disconnected,
when the OPA875 is switched from channel 0 to
channel 1, to prevent the transmit pulse from going
through the receive signal chain. This architecture is
shown in Figure 26.
When channel 0 is selected, the overall gain to the
matched load of the OPA875 is 0dB. When channel 1
is selected, this circuit delivers an 18dB gain to the
matched load.
HIGH ISOLATION RGB VIDEO MUX
Three OPA875s can be used as a triple, 2:1 video
MUX (see Figure 27). This configuration has the
advantage of having higher R to G to B isolation than
a comparable and more integrated solution does,
such as the OPA3875, especially at higher
frequencies. This comparison is shown in Figure 28.
+5V
+5V
OPA695
50W
Channel 0
-5V
523W
IN
50W
Source
OPA875
x1
50W
x2
50W
50W
Channel 1
+5V
50W
Load
x1
OPA695
-5V
-5V
402W
57.6W
Figure 25. 1-Bit, High-Speed PGA
OPA875
Receive Channel
Channel 0
x1
x2
Channel 1
x1
Figure 26. Transmit/Receive Switch
Submit Documentation Feedback
Copyright © 2006–2008, Texas Instruments Incorporated
Product Folder Link(s): OPA875
9
OPA875
SBOS340C – DECEMBER 2006 – REVISED AUGUST 2008 ............................................................................................................................................ www.ti.com
4-INPUT RGB ROUTER
OPA875_A
Ch 0
Two OPA875s can be used together to form a
four-input RGB router. The router for the red
component is shown in Figure 29.
x1
ROUT
x2
OPA875
Ch 1
x1
R1
x1
RO
69W
x2
OPA875_B
Ch 0
x1
R2
x1
EN
GOUT
x2
Ch 1
x1
R3
x1
RO
69W
OPA875_C
Ch 0
75W
x1
R4
x1
EN
BOUT
x2
Ch 1
Red
Out
x2
Chip
Select
x1
Figure 29. 4-Input RGB Router
Figure 27. High Isolation RGB Video MUX
0
Input-Referred
-10
Crosstalk (dB)
-20
-30
When connecting OPA875 outputs together, maintain
a gain of +1 at the load. The OPA875 operates at a
gain of +6dB; thus, matching resistance must be
selected to achieve –6dB attenuation.
OPA3875
OPA3875
All Hostile
Adjacent Channel Crosstalk
Crosstalk
The set of equations to solve are shown in
Equation 1 and Equation 2. Here, the impedance of
interest is ZO = 75Ω.
OPA875_C
Ch. 0 Driven
Adjacent Channel Crosstalk
-40
RO = ZO || (R + RF + RG)
-50
1+
-60
OPA875
OPA875_A
All Hostile
Ch. 1 Driven, Adjacent
Crosstalk
Channel Crosstalk
-70
-80
-90
1
10
100
RF
RG
=2
RF + RG = 804W
RF = RG
(2)
1G
Frequency (MHz)
Solving for RO with n devices connected together, we
get Equation 3:
Figure 28. All Hostile and Adjacent Channel
Crosstalk
RO =
75 ´ (n - 1) + 804
The configuration of the three OPA875 devices used
is shown in Figure 27. Note that for the test, the
OPA875_B was measured when both the OPA875_A
and OPA875_C were driven for all hostile crosstalk
and only the OPA875_A or OPA875_C was driven for
the adjacent channel crosstalk.
10
(1)
Submit Documentation Feedback
2
´
1+
241200
[75 ´ (n - 1) + 804]
2
-1
(3)
Copyright © 2006–2008, Texas Instruments Incorporated
Product Folder Link(s): OPA875
OPA875
www.ti.com ............................................................................................................................................ SBOS340C – DECEMBER 2006 – REVISED AUGUST 2008
Results for n varying from 2 to 6 are given in Table 2.
Table 2. Series Resistance versus Number of
Parallel Outputs
NUMBER OF OPA875s
RO (Ω)
2
69
3
63.94
4
59.49
5
55.59
6
52.15
The two major limitations of this circuit are the device
requirements for each OPA875 and the acceptable
return loss because of the mismatch between the
load (75Ω) and the matching resistor.
DESIGN-IN TOOLS
DEMONSTRATION FIXTURES
Two printed circuit boards (PCBs) are available to
assist in the initial evaluation of circuit performance
using the OPA875. These fixtures are offered free of
charge as unpopulated PCBs, delivered with a user's
guide. The summary information for these fixtures is
shown in Table 3.
Table 3. OPA875 Demonstration Fixtures
PRODUCT
PACKAGE
ORDERING NUMBER
LITERATURE
NUMBER
OPA875IDGK
MSOP-8
DEM-OPA-MSOP-1B
SBOU044
OPA875ID
SO-8
DEM-OPA-SO-1D
SBOU049
The demonstration fixture can be requested at the
Texas Instruments web site at (www.ti.com) through
the OPA875 product folder.
MACROMODELS AND APPLICATIONS
SUPPORT
Computer simulation of circuit performance using
SPICE is often useful when analyzing the
performance of analog circuits and systems. This is
particularly true for video and RF amplifier circuits
where parasitic capacitance and inductance can have
a major effect on circuit performance. A SPICE model
for the OPA875 is available through the Texas
Instruments web site at www.ti.com. These models
do a good job of predicting small-signal AC and
transient performance under a wide variety of
operating conditions. They do not do as well in
predicting the harmonic distortion or dG/dP
characteristics. These models do not attempt to
distinguish between the package types in their
small-signal AC performance.
OPERATING SUGGESTIONS
DRIVING CAPACITIVE LOADS
One of the most demanding, yet very common load
conditions is capacitive loading. Often, the capacitive
load is the input of an ADC—including additional
external capacitance that may be recommended to
improve ADC linearity. A high-speed device such as
the OPA875 can be very susceptible to decreased
stability and closed-loop response peaking when a
capacitive load is placed directly on the output pin.
When the device open-loop output resistance is
considered, this capacitive load introduces an
additional pole in the signal path that can decrease
the phase margin. Several external solutions to this
problem have been suggested. When the primary
considerations are frequency response flatness,
pulse response fidelity, and/or distortion, the simplest
and most effective solution is to isolate the capacitive
load from the feedback loop by inserting a series
isolation resistor between the amplifier output and the
capacitive load. This isolation resistor does not
eliminate the pole from the loop response, but rather
shifts it and adds a zero at a higher frequency. The
additional zero acts to cancel the phase lag from the
capacitive load pole, thus increasing the phase
margin and improving stability.
The Typical Characteristics show the recommended
RS versus capacitive load and the resulting frequency
response at the load; see Figure 5. Parasitic
capacitive loads greater than 2pF can begin to
degrade the performance of the OPA875. Long PCB
traces, unmatched cables, and connections to
multiple devices can easily cause this value to be
exceeded. Always consider this effect carefully, and
add the recommended series resistor as close as
possible to the OPA875 output pin (see the Board
Layout Guidelines section).
DC ACCURACY
The OPA875 offers excellent DC signal accuracy.
Parameters that influence the output DC offset
voltage are:
• Output offset voltage
• Input bias current
• Gain error
• Power-supply rejection ratio
• Temperature
Submit Documentation Feedback
Copyright © 2006–2008, Texas Instruments Incorporated
Product Folder Link(s): OPA875
11
OPA875
SBOS340C – DECEMBER 2006 – REVISED AUGUST 2008 ............................................................................................................................................ www.ti.com
Leaving both temperature and gain error parameters
aside, the output offset voltage envelope can be
described as shown in Equation 4:
VOSO_envelope = VOSO + (RS·Ib) x G ± |5 - (VS+)| x 10
± |-5 - (VS-)| x 10
- PSRR+
20
- PSRR20
(4)
With:
VOSO: Output offset voltage
RS: Input resistance seen by R0, R1, G0, G1, B0,
or B1.
Ib: Input bias current
G: Gain
VS+: Positive supply voltage
VS–: Negative supply voltage
PSRR+: Positive supply PSRR
PSRR–: Negative supply PSRR
Evaluating the front-page schematic, using a
worst-case, +25°C offset voltage, bias current and
PSRR specifications and operating at ±6V, gives a
worst-case output equal to Equation 5:
- 50
20
±14mV + 75W x ±18mA x 2 ± |5 - 6| x 10
- 51
20
± |-5 - (-6)| x 10
= ±22.7mV
output stage continues to hold them low even as the
fundamental power reaches very high levels. As the
Typical
Characteristics
show,
the
spurious
intermodulation powers do not increase as predicted
by a traditional intercept model. As the fundamental
power level increases, the dynamic range does not
decrease significantly. For two tones centered at
20MHz, with 4dBm/tone into a matched 50Ω load
(that is, 1VPP for each tone at the load, which requires
4VPP for the overall 2-tone envelope at the output
pin), the Typical Characteristics show a 82dBc
difference between the test-tone power and the
3rd-order intermodulation spurious levels.
NOISE PERFORMANCE
The OPA875 offers an excellent balance between
voltage and current noise terms to achieve low output
noise. As long as the AC source impedance looking
out of the noninverting node is less than 100Ω, this
current noise will not contribute significantly to the
total output noise. The device input voltage noise and
the input current noise terms combine to give low
output noise under a wide variety of operating
conditions. Figure 30 shows this device noise
analysis model with all the noise terms included. In
this model, all noise terms are taken to be noise
voltage or current density terms in either nV/√Hz or
pA/√Hz.
+5V
(5)
DISTORTION PERFORMANCE
The OPA875 provides good distortion performance
into a 100Ω load on ±5V supplies. Relative to
alternative solutions, it provides exceptional
performance into lighter loads. Generally, until the
fundamental signal reaches very high frequency or
power levels, the 2nd-harmonic dominates the
distortion with a negligible 3rd-harmonic component.
Focusing then on the 2nd-harmonic, increasing the
load impedance improves distortion directly. Also,
providing an additional supply decoupling capacitor
(0.01µF) between the supply pins (for bipolar
operation) improves the 2nd-order distortion slightly
(3dB to 6dB).
In most op amps, increasing the output voltage swing
increases harmonic distortion directly. The Typical
Characteristics show the 2nd-harmonic increasing at
a little less than the expected 2X rate while the
3rd-harmonic increases at a little less than the
expected 3X rate. Where the test power doubles, the
2nd-harmonic increases only by less than the
expected 6dB, whereas the 3rd-harmonic increases
by less than the expected 12dB. This also shows up
in the two-tone, 3rd-order intermodulation spurious
(IM3) response curves. The 3rd-order spurious levels
are extremely low at low output power levels. The
12
OPA875
en
+1
RS
ib
eO
+2
+1
e RS
-5V
Channel
Select
EN
Figure 30. Noise Model
The total output spot noise voltage can be computed
as the square root of the sum of all squared output
noise voltage contributors. Equation 6 shows the
general form for the output noise voltage using the
terms shown in Figure 30.
eo = 2
2
2
en + (ibRS) + 4kTRS
Submit Documentation Feedback
(6)
Copyright © 2006–2008, Texas Instruments Incorporated
Product Folder Link(s): OPA875
OPA875
www.ti.com ............................................................................................................................................ SBOS340C – DECEMBER 2006 – REVISED AUGUST 2008
Dividing this expression by the device gain (2V/V)
gives the equivalent input-referred spot noise voltage
at the noninverting input as shown in Equation 7.
en =
2
2
en + (ibRS) + 4kTRS
(7)
Evaluating these two equations for the OPA875
circuit and component values shown in Figure 30
gives a total output spot noise voltage of 13.6nV/√Hz
and a total equivalent input spot noise voltage of
6.8nV/√Hz. This total input-referred spot noise
voltage is higher than the 6.7nV/√Hz specification for
the mux voltage noise alone. This number reflects the
noise added to the output by the bias current noise
times the source resistor.
THERMAL ANALYSIS
Heatsinking or forced airflow may be required under
extreme operating conditions. Maximum desired
junction temperature will set the maximum allowed
internal power dissipation as discussed in this
document. In no case should the maximum junction
temperature be allowed to exceed +150°C.
Operating junction temperature (TJ) is given by TA +
PD × θJA. The total internal power dissipation (PD) is
the sum of quiescent power (PDQ) and additional
power dissipated in the output stage (PDL) to deliver
load power. Quiescent power is simply the specified
no-load supply current times the total supply voltage
across the part. PDL depends on the required output
signal and load but, for a grounded resistive load, be
at a maximum when the output is fixed at a voltage
equal to 1/2 of either supply voltage (for equal bipolar
supplies). Under this condition PDL = VS2/(4 × RL),
where RL includes feedback network loading.
Note that it is the power in the output stage and not in
the load that determines internal power dissipation.
As a worst-case example, compute the maximum TJ
using an OPA875IDGK in the circuit of Figure 30
operating at the maximum specified ambient
temperature of +85°C with its outputs driving a
grounded 100Ω load to +2.5V:
2
PD = 10V x 11mA + (5 [4 x (100W || 804W) ] ) = 180mW
Maximum TJ = +85°C + (0.18mW x 140°C/W) = 110°C
This worst-case condition does not exceed the
maximum junction temperature. Normally, this
extreme case is not encountered. Careful attention to
internal power dissipation is required.
BOARD LAYOUT GUIDELINES
Achieving optimum performance with a high
frequency amplifier such as the OPA875 requires
careful attention to board layout parasitics and
external component types. Recommendations that
will optimize performance include:
a) Minimize parasitic capacitance to any AC
ground for all of the signal I/O pins. Parasitic
capacitance on the output pin can cause instability:
on the noninverting input, it can react with the source
impedance to cause unintentional bandlimiting. To
reduce unwanted capacitance, a window around the
signal I/O pins should be opened in all of the ground
and power planes around those pins. Otherwise,
ground and power planes should be unbroken
elsewhere on the board.
b) Minimize the distance (< 0.25") from the
power-supply pins to high frequency 0.1µF
decoupling capacitors. At the device pins, the
ground and power plane layout should not be in close
proximity to the signal I/O pins. Avoid narrow power
and ground traces to minimize inductance between
the pins and the decoupling capacitors. The
power-supply connections (on pins 9, 11, 13, and 15)
should always be decoupled with these capacitors.
An optional supply decoupling capacitor across the
two power supplies (for bipolar operation) will improve
2nd-harmonic distortion performance. Larger (2.2µF
to 6.8µF) decoupling capacitors, effective at lower
frequency, should also be used on the main supply
pins. These may be placed somewhat farther from
the device and may be shared among several
devices in the same area of the PCB.
c) Careful selection and placement of external
components will preserve the high-frequency
performance of the OPA875. Resistors should be a
very low reactance type. Surface-mount resistors
work best and allow a tighter overall layout. Metal-film
and carbon composition, axially leaded resistors can
also provide good high-frequency performance.
Again, keep the leads and PCB trace length as short
as possible. Never use wirewound type resistors in a
high-frequency
application.
Other
network
components, such as noninverting input termination
resistors, should also be placed close to the package.
d) Connections to other wideband devices on the
board may be made with short direct traces or
through onboard transmission lines. For short
connections, consider the trace and the input to the
next device as a lumped capacitive load. Relatively
wide traces (50mils to 100mils) should be used,
preferably with ground and power planes opened up
around them.
Submit Documentation Feedback
Copyright © 2006–2008, Texas Instruments Incorporated
Product Folder Link(s): OPA875
13
OPA875
SBOS340C – DECEMBER 2006 – REVISED AUGUST 2008 ............................................................................................................................................ www.ti.com
Estimate the total capacitive load and set RS from the
plot of Figure 5. Low parasitic capacitive loads (<
5pF) may not need an RS because the OPA875 is
nominally compensated to operate with a 2pF
parasitic load. If a long trace is required, and the 6dB
signal loss intrinsic to a doubly-terminated
transmission line is acceptable, implement a matched
impedance transmission line using microstrip or
stripline techniques (consult an ECL design handbook
for microstrip and stripline layout techniques). A 50Ω
environment is normally not necessary on board, and
in fact, a higher impedance environment will improve
distortion as shown in the Distortion versus Load
plots. With a characteristic board trace impedance
defined based on board material and trace
dimensions, a matching series resistor into the trace
from the output of the OPA875 is used as well as a
terminating shunt resistor at the input of the
destination device. Remember also that the
terminating impedance will be the parallel
combination of the shunt resistor and the input
impedance of the destination device; this total
effective impedance should be set to match the trace
impedance. The high output voltage and current
capability of the OPA875 allows multiple destination
devices to be handled as separate transmission lines,
each with their own series and shunt terminations. If
the 6dB attenuation of a doubly-terminated
transmission line is unacceptable, a long trace can be
seriesterminated at the source end only. Treat the
trace as a capacitive load in this case and set the
series resistor value as shown in Figure 5. This will
not preserve signal integrity as well as a
doubly-terminated line. If the input impedance of the
destination device is low, there will be some signal
attenuation due to the voltage divider formed by the
series output into the terminating impedance.
14
e) Socketing a high-speed part like the OPA875 is
not recommended. The additional lead length and
pin-to-pin capacitance introduced by the socket can
create an extremely troublesome parasitic network
which can make it almost impossible to achieve a
smooth, stable frequency response. Best results are
obtained by soldering the OPA875 onto the board.
INPUT AND ESD PROTECTION
The OPA875 is built using a very high-speed
complementary bipolar process. The internal junction
breakdown voltages are relatively low for these very
small geometry devices. These breakdowns are
reflected in the Absolute Maximum Ratings table. All
device pins have limited ESD protection using internal
diodes to the power supplies as shown in Figure 31.
+VCC
External
Pin
Internal
Circuitry
-VCC
Figure 31. Internal ESD Protection
These diodes provide moderate protection to input
overdrive voltages above the supplies as well. The
protection diodes can typically support 30mA
continuous current. Where higher currents are
possible (for example, in systems with ±15V supply
parts driving into the OPA875), current-limiting series
resistors should be added into the two inputs. Keep
these resistor values as low as possible because high
values degrade both noise performance and
frequency response.
Submit Documentation Feedback
Copyright © 2006–2008, Texas Instruments Incorporated
Product Folder Link(s): OPA875
OPA875
www.ti.com ............................................................................................................................................ SBOS340C – DECEMBER 2006 – REVISED AUGUST 2008
Revision History
Changes from Revision B (September 2007) to Revision C .......................................................................................... Page
•
Changed storage temperature range rating in Absolute Maximum Ratings table from –40°C to +125°C to –65°C to
+125°C ................................................................................................................................................................................... 2
Changes from Revision A (August 2007) to Revision B ................................................................................................ Page
•
Changed ordering information column in Table 3................................................................................................................ 11
Submit Documentation Feedback
Copyright © 2006–2008, Texas Instruments Incorporated
Product Folder Link(s): OPA875
15
PACKAGE OPTION ADDENDUM
www.ti.com
7-Apr-2016
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
OPA875ID
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA875
OPA875IDG4
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA875
OPA875IDGKR
ACTIVE
VSSOP
DGK
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU |
CU NIPDAUAG
Level-2-260C-1 YEAR
BPL
OPA875IDGKT
ACTIVE
VSSOP
DGK
8
250
Green (RoHS
& no Sb/Br)
CU NIPDAUAG
Level-2-260C-1 YEAR
BPL
OPA875IDGKTG4
ACTIVE
VSSOP
DGK
8
250
Green (RoHS
& no Sb/Br)
CU NIPDAUAG
Level-2-260C-1 YEAR
BPL
OPA875IDR
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
OPA875
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
7-Apr-2016
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Jan-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
OPA875IDGKR
VSSOP
DGK
8
OPA875IDGKT
VSSOP
DGK
OPA875IDR
SOIC
D
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
2500
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
8
250
180.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Jan-2013
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
OPA875IDGKR
VSSOP
DGK
8
2500
367.0
367.0
35.0
OPA875IDGKT
VSSOP
DGK
8
250
210.0
185.0
35.0
OPA875IDR
SOIC
D
8
2500
367.0
367.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2016, Texas Instruments Incorporated