TI TL5001ACDR

TL5001, TL5001A
PULSE-WIDTH-MODULATION CONTROL CIRCUITS
SLVS084F – APRIL 1994 – REVISED JANUARY 2002
1
8
2
7
3
6
4
5
GND
RT
DTC
SCP
3
2
1
20 19
NC
GND
FK PACKAGE
(TOP VIEW)
NC
D
OUT
VCC
COMP
FB
OUT
D
D, JG OR P PACKAGE
(TOP VIEW)
Complete PWM Power Control
3.6-V to 40-V Operation
Internal Undervoltage-Lockout Circuit
Internal Short-Circuit Protection
Oscillator Frequency . . . 20 kHz to 500 kHz
Variable Dead Time Provides Control Over
Total Range
±3% Tolerance on Reference Voltage
(TL5001A)
Available in Q-Temp Automotive
HighRel Automotive Applications
Configuration Control / Print Support
Qualification to Automotive Standards
NC
D
D
D
D
D
D
NC
4
18 NC
VCC
5
17 RT
NC
6
16 NC
COMP
7
15 DTC
description
NC
SCP
NC
FB
NC
The TL5001 and TL5001A incorporate on a single
NC 8
14 NC
monolithic chip all the functions required for a
9 10 11 12 13
pulse-width-modulation (PWM) control circuit. Designed primarily for power-supply control, the
TL5001/A contains an error amplifier, a regulator, an
oscillator, a PWM comparator with a dead-time-control
input,
undervoltage
lockout
(UVLO), short-circuit protection (SCP), and an open-collector output transistor. The TL5001A has a typical
reference voltage tolerance of ±3% compared to ±5% for the TL5001.
The error-amplifier common-mode voltage ranges from 0 V to 1.5 V. The noninverting input of the error amplifier
is connected to a 1-V reference. Dead-time control (DTC) can be set to provide 0% to 100% dead time by connecting
an external resistor between DTC and GND. The oscillator frequency is set by terminating RT with an external
resistor to GND. During low VCC conditions, the UVLO circuit turns the output off until VCC recovers to its normal
operating range.
The TL5001C and TL5001AC are characterized for operation from – 20°C to 85°C. The TL5001I and TL5001AI are
characterized for operation from – 40°C to 85°C. The TL5001Q and TL5001AQ are characterized for operation from
– 40°C to 125°C. The TL5001M and TL5001AM are characterized for operation from – 55°C to 125°C.
AVAILABLE OPTIONS
PACKAGED DEVICES
TA
– 20°C to 85°C
– 40°C to 85°C
– 40°C to 125°C
SMALL OUTLINE
(D)
PLASTIC DIP
(P)
CERAMIC DIP
(JG)
CHIP CARRIER
(FK)
TL5001CD
TL5001CP
—
—
TL5001ACD
TL5001ACP
—
—
TL5001ID
TL5001IP
—
—
TL5001AID
TL5001AIP
—
—
—
—
TL5001QD
—
TL5001AQD
—
—
—
TL5001MJG
TL5001MFK
—
—
TL5001AMJG
TL5001AMFK
– 55°C to 125°C
—
—
The D package is available taped and reeled. Add the suffix R to the device type (e.g., TL5001CDR).
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright  2002, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303
On products compliant to MIL-PRF-38535, all parameters are tested
unless otherwise noted. On all other products, production
processing does not necessarily include testing of all parameters.
• DALLAS, TEXAS 75265
1
TL5001, TL5001A
PULSE-WIDTH-MODULATION CONTROL CIRCUITS
SLVS084F – APRIL 1994 – REVISED JANUARY 2002
schematic for typical application
VI
+
TPS1101
VO
+
2
VCC
5 SCP
VO
COMP
1
3
TL5001/A
6
7
DTC
FB
4
RT
GND
8
functional block diagram
VCC
2
DTC
6
RT
7
OUT
1
UVLO
IDT
2.5 V
1V
1.5 V
Error
Amplifier
Reference
Voltage
1V
SCP
Comparator 1
OSC
PWM/DTC
Comparator
+
FB
COMP
4
–
3
SCP
Comparator 2
SCP
5
8
GND
2
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TL5001, TL5001A
PULSE-WIDTH-MODULATION CONTROL CIRCUITS
SLVS084F – APRIL 1994 – REVISED JANUARY 2002
detailed description
voltage reference
A 2.5-V regulator operating from VCC is used to power the internal circuitry of the TL5001 and TL5001A and as a
reference for the error amplifier and SCP circuits. A resistive divider provides a 1-V reference for the error amplifier
noninverting input which typically is within 2% of nominal over the operating temperature range.
error amplifier
The error amplifier compares a sample of the dc-to-dc converter output voltage to the 1-V reference and generates
an error signal for the PWM comparator. The dc-to-dc converter output voltage is set by selecting the error-amplifier
gain (see Figure 1), using the following expression:
VO = (1 + R1/R2) (1 V)
Compensation
Network
R1
VI(FB)
3
COMP
4
FB
TL5001/A
–
R2
+
8 GND
To PWM
Comparator
Vref = 1 V
Figure 1. Error-Amplifier Gain Setting
The error-amplifier output is brought out as COMP for use in compensating the dc-to-dc converter control loop for
stability. Because the amplifier can only source 45 µA, the total dc load resistance should be 100 kΩ or more.
oscillator/PWM
The oscillator frequency (fosc) can be set between 20 kHz and 500 kHz by connecting a resistor between RT and
GND. Acceptable resistor values range from 15 kΩ to 250 kΩ. The oscillator frequency can be determined by using
the graph shown in Figure 5.
The oscillator output is a triangular wave with a minimum value of approximately 0.7 V and a maximum value of
approximately 1.3 V. The PWM comparator compares the error-amplifier output voltage and the DTC input voltage
to the triangular wave and turns the output transistor off whenever the triangular wave is greater than the lesser of
the two inputs.
dead-time control (DTC)
DTC provides a means of limiting the output-switch duty cycle to a value less than 100 %, which is critical for boost
and flyback converters. A current source generates a reference current (IDT) at DTC that is nominally equal to the
current at the oscillator timing terminal, RT. Connecting a resistor between DTC and GND generates a dead-time
reference voltage (VDT), which the PWM/DTC comparator compares to the oscillator triangle wave as described
in the previous section. Nominally, the maximum duty cycle is 0 % when VDT is 0.7 V or less and 100 % when VDT
is 1.3 V or greater. Because the triangle wave amplitude is a function of frequency and the source impedance of
RT is relatively high (1250 Ω), choosing RDT for a specific maximum duty cycle, D, is accomplished using the
following equation and the voltage limits for the frequency in question as found in Figure 11 (Voscmax and Voscmin
are the maximum and minimum oscillator levels):
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
TL5001, TL5001A
PULSE-WIDTH-MODULATION CONTROL CIRCUITS
SLVS084F – APRIL 1994 – REVISED JANUARY 2002
dead-time control (DTC) (continued)
R
DT
ǒ
Ǔƪ ǒ
+ Rt ) 1250
Ǔ ) Voscminƫ
D V oscmax – V oscmin
Where
RDT and Rt are in ohms, D in decimal
ǒ
Ǔ
Soft start can be implemented by paralleling the DTC resistor with a capacitor (CDT) as shown in Figure 2. During
soft start, the voltage at DTC is derived by the following equation:
V
DT
[ IDTRDT
1– e
ǒ
ń
–t R
Ǔ
C
DT DT
6 DTC
CDT
TL5001/A
RDT
Figure 2. Soft-Start Circuit
If the dc-to-dc converter must be in regulation within a specified period of time, the time constant, RDTCDT, should
be t0/3 to t0/5. The TL5001/A remains off until VDT ≈ 0.7 V, the minimum ramp value. CDT is discharged every time
UVLO or SCP becomes active.
undervoltage-lockout (UVLO) protection
The undervoltage-lockout circuit turns the output transistor off and resets the SCP latch whenever the supply voltage
drops too low (approximately 3 V at 25°C) for proper operation. A hysteresis voltage of 200 mV eliminates false
triggering on noise and chattering.
short-circuit protection (SCP)
The TL5001/A includes short-circuit protection (see Figure 3), which turns the power switch off to prevent damage
when the converter output is shorted. When activated, the SCP prevents the switch from being turned on until the
internal latching circuit is reset. The circuit is reset by reducing the input voltage until UVLO becomes active or until
the SCP terminal is pulled to ground externally.
When a short circuit occurs, the error-amplifier output at COMP rises to increase the power-switch duty cycle in an
attempt to maintain the output voltage. SCP comparator 1 starts an RC timing circuit when COMP exceeds 1.5 V.
If the short is removed and the error-amplifier output drops below 1.5 V before time out, normal converter operation
continues. If the fault is still present at the end of the time-out period, the timer sets the latching circuit and turns
off the TL5001/A output transistor.
4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TL5001, TL5001A
PULSE-WIDTH-MODULATION CONTROL CIRCUITS
SLVS084F – APRIL 1994 – REVISED JANUARY 2002
short-circuit protection (SCP) (continued)
2.5 V
RSCP
185 kΩ
12 kΩ
CSCP
SCP
5
From Error
Amp
1.5 V
SCP
Comparator 2
To Output
Drive Logic
Q1
Vref = 1 V
SCP
Comparator 1
Q2
Figure 3. SCP Circuit
The timer operates by charging an external capacitor (CSCP), connected between the SCP terminal and ground,
towards 2.5 V through a 185-kΩ resistor (RSCP). The circuit begins charging from an initial voltage of approximately
185 mV and times out when the capacitor voltage reaches 1 V. The output of SCP comparator 2 then goes high,
turns on Q2, and latches the timer circuit. The expression for setting the SCP time period is derived from the following
equation:
V
SCP
ǒ
Ǔ
+ (2.5 * 0.185) 1 * e–tń ) 0.185
t
Where
τ = RSCPCSCP
The end of the time-out period, tSCP, occurs when VSCP = 1 V. Solving for CSCP yields:
C SCP
+ 12.46
t SCP
Where
t is in seconds, C in µF.
tSCP must be much longer (generally 10 to 15 times) than the converter start-up period or the converter will not start.
output transistor
The output of the TL5001/A is an open-collector transistor with a maximum collector current rating of 21 mA and
a voltage rating of 51 V. The output is turned on under the following conditions: the oscillator triangle wave is lower
than both the DTC voltage and the error-amplifier output voltage, the UVLO circuit is inactive, and the short-circuit
protection circuit is inactive.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
TL5001, TL5001A
PULSE-WIDTH-MODULATION CONTROL CIRCUITS
SLVS084F – APRIL 1994 – REVISED JANUARY 2002
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 V
Amplifier input voltage, VI(FB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 V
Output voltage, VO, OUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 V
Output current, IO, OUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 mA
Output peak current, IO(peak), OUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 mA
Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table
Operating ambient temperature range, TA: TL5001C, TL5001AC . . . . . . . . . . . . . . . . . . . . . . – 20°C to 85°C
TL5001I, TL5001AI . . . . . . . . . . . . . . . . . . . . . . . . – 40°C to 85°C
TL5001Q, TL5001AQ . . . . . . . . . . . . . . . . . . . . . – 40°C to 125°C
TL5001M, TL5001AM . . . . . . . . . . . . . . . . . . . . . – 55°C to 125°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied.
Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTE 1: All voltage values are with respect to network ground terminal.
DISSIPATION RATING TABLE
PACKAGE
TA ≤ 25°C
POWER RATING
DERATING FACTOR
ABOVE TA = 25°C
TA = 70°C
POWER RATING
TA = 85°C
POWER RATING
TA = 125°C
POWER RATING
D
725 mW
5.8 mW/°C
464 mW
377 mW
145 mW
FK
1375 mW
11.0 mW/°C
880 mW
715 mW
275 mW
JG
1050 mW
8.4 mW/°C
672 mW
546 mW
210 mW
P
1000 mW
8.0 mW/°C
640 mW
520 mW
200 mW
recommended operating conditions
Supply voltage, VCC
Amplifier input voltage, VI(FB)
MIN
MAX
3.6
40
UNIT
V
0
1.5
V
Output voltage, VO, OUT
50
V
Output current, IO, OUT
20
mA
COMP source current
45
COMP dc load resistance
100
µA
kΩ
Oscillator timing resistor, Rt
15
250
kΩ
Oscillator frequency, fosc
20
500
kHz
TL5001C, TL5001AC
– 20
85
TL5001I, TL5001AI
– 40
85
TL5001Q, TL5001AQ
– 40
125
TL5001M, TL5001AM
– 55
125
Operating ambient temperature,
temperature TA
6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
°C
TL5001, TL5001A
PULSE-WIDTH-MODULATION CONTROL CIRCUITS
SLVS084F – APRIL 1994 – REVISED JANUARY 2002
electrical characteristics over recommended operating free-air temperature range, VCC = 6 V,
fosc = 100 kHz (unless otherwise noted)
reference
PARAMETER
TEST CONDITIONS
Output voltage
COMP connected to FB
Input regulation
VCC = 3.6 V to 40 V
TA = – 20°C to 25°C (C suffix)
Output voltage change with temperature
TA = – 40°C to 25°C (I suffix)
TA = 25°C to 85°C
TL5001C, TL5001I
MIN TYP†
MAX
0.95
1
1.05
2
12.5
– 10
–1
10
– 10
–1
10
– 10
–2
10
TL5001AC, TL5001AI
MIN TYP†
MAX
0.97
UNIT
1
1.03
V
2
12.5
mV
– 10
–1
10
– 10
–1
10
– 10
–2
10
mV/V
† All typical values are at TA = 25°C.
undervoltage lockout
PARAMETER
Upper threshold voltage
TEST CONDITIONS
TL5001C, TL5001I
MIN TYP†
MAX
Lower threshold voltage
TA = 25°C
TA = 25°C
Hysteresis
TA = 25°C
100
200
TA = 25°C
2.1
2.55
Reset threshold voltage
† All typical values are at TA = 25°C.
TL5001AC, TL5001AI
MIN TYP†
MAX
UNIT
3
3
2.8
2.8
V
V
100
200
mV
2.1
2.55
V
short-circuit protection
PARAMETER
SCP threshold voltage
TEST CONDITIONS
SCP voltage, latched
TA = 25°C
No pullup
SCP voltage, UVLO standby
No pullup
Input source current
TA = 25°C
TL5001C, TL5001I
MIN TYP†
MAX
TL5001AC, TL5001AI
MIN TYP†
MAX
UNIT
0.95
1.00
1.05
0.97
1.00
1.03
V
140
185
230
140
185
230
mV
60
120
60
120
mV
–15
–20
–15
–20
µA
–10
SCP comparator 1 threshold voltage
† All typical values are at TA = 25°C.
–10
1.5
1.5
V
oscillator
PARAMETER
Frequency
TEST CONDITIONS
TL5001C, TL5001I
MIN TYP†
MAX
Rt = 100 kΩ
Standard deviation of frequency
Frequency change with voltage
Frequency change with temperature
VCC = 3.6 V to 40 V
TA = – 40°C to 25°C
TA = – 20°C to 25°C
TA = 25°C to 85°C
UNIT
100
100
kHz
15
15
kHz
1
1
kHz
–4
– 0.4
4
–4
– 0.4
4
kHz
–4
– 0.4
4
–4
– 0.4
4
kHz
–4
– 0.2
4
–4
– 0.2
4
kHz
Voltage at RT
† All typical values are at TA = 25°C.
1
POST OFFICE BOX 655303
TL5001AC, TL5001AI
MIN TYP†
MAX
• DALLAS, TEXAS 75265
1
V
7
TL5001, TL5001A
PULSE-WIDTH-MODULATION CONTROL CIRCUITS
SLVS084F – APRIL 1994 – REVISED JANUARY 2002
electrical characteristics over recommended operating free-air temperature range, VCC = 6 V,
fosc = 100 kHz (unless otherwise noted) (continued)
dead-time control
PARAMETER
Output (source) current
TL5001C, TL5001I
MIN
TYP†
MAX
TEST CONDITIONS
TL5001C
TL5001I
V(DT) = 1.5 V
V(DT) = 1.5 V
0.9 × IRT‡
0.9 × IRT‡
Duty cycle = 0%
Input threshold voltage
0.5
Duty cycle = 100%
1.1 × IRT
1.2 × IRT
0.7
TL5001AC, TL5001AI
MIN
TYP†
MAX
0.9 × IRT‡
0.9 × IRT‡
1.1 × IRT
1.2 × IRT
0.5
1.3
UNIT
0.7
1.5
1.3
µA
V
1.5
† All typical values are at TA = 25°C.
‡ Output source current at RT
error amplifier
PARAMETER
TEST CONDITIONS
Input voltage
TL5001C, TL5001I
MIN TYP†
MAX
VCC = 3.6 V to 40 V
0
Input bias current
1.5
– 160
Output voltage swing
Positive
1.5
Negative
0
– 500
2.3
0.3
Open-loop voltage amplification
TL5001AC, TL5001AI
MIN TYP†
MAX
– 160
1.5
0.4
Unity-gain bandwidth
1.5
Output (sink) current
VI(FB) = 1.2 V, COMP = 1 V
VI(FB) = 0.8 V, COMP = 1 V
Output (source) current
† All typical values are at TA = 25°C.
1.5
V
– 500
nA
2.3
0.3
80
UNIT
V
0.4
V
80
dB
1.5
MHz
100
600
100
600
µA
– 45
– 70
– 45
– 70
µA
output
PARAMETER
TEST CONDITIONS
Output saturation voltage
IO = 10 mA
VO = 50 V,
Off state current
Off-state
TL5001C, TL5001I
MIN TYP†
MAX
1.5
VCC = 0
VO = 50 V
VO = 6 V
Short-circuit output current
† All typical values are at TA = 25°C.
2
TL5001AC, TL5001AI
MIN TYP†
MAX
1.5
2
10
10
10
10
40
40
UNIT
V
µA
mA
total device
PARAMETER
Standby supply current
Average supply current
† All typical values are at TA = 25°C.
8
TEST CONDITIONS
TL5001C, TL5001I
MIN TYP†
MAX
Off state
Rt = 100 kΩ
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TL5001AC, TL5001AI
MIN TYP†
MAX
UNIT
1
1.5
1
1.5
mA
1.4
2.1
1.4
2.1
mA
TL5001, TL5001A
PULSE-WIDTH-MODULATION CONTROL CIRCUITS
SLVS084F – APRIL 1994 – REVISED JANUARY 2002
electrical characteristics over recommended operating free-air temperature range, VCC = 6 V,
fosc = 100 kHz (unless otherwise noted)
reference
PARAMETER
TEST CONDITIONS
Output voltage
TA = 25°C
TA = MIN to MAX
COMP connected to FB
Input regulation
TA = MIN to MAX
VCC = 3.6 V to 40 V
Output voltage change with temperature
† All typical values are at TA = 25°C.
*Not production tested.
TA = MIN to MAX
TL5001Q,
TL5001M
MIN TYP†
MAX
TL5001AQ,
TL5001AM
MIN TYP†
MAX
0.95
1.00
1.05
0.97
1.00
1.03
0.93
0.98
1.07
0.94
0.98
1.06
2
12.5
2
12.5
2
*6
2
*6
*– 6
*– 6
UNIT
V
mV
%
undervoltage lockout
PARAMETER
TL5001Q,
TL5001M
TEST CONDITIONS
MIN
TYP†
TL5001AQ,
TL5001AM
MAX
MIN
TYP†
Upper threshold voltage
TA = MIN, 25°C
TA = MAX
3.00
3.00
2.55
2.55
Lower threshold voltage
TA = MIN, 25°C
TA = MAX
2.8
2.8
2.0
2.0
Hysteresis
TA = MIN to MAX
100
200
100
200
Reset threshold voltage
TA = MIN, 25°C
TA = MAX
2.10
2.55
2.10
2.55
0.35
0.63
0.35
0.63
UNIT
MAX
V
V
mV
V
† All typical values are at TA = 25°C.
short-circuit protection
PARAMETER
SCP threshold voltage
SCP voltage, latched
SCP voltage, UVLO standby
Equivalent timing resistance
SCP comparator 1 threshold voltage
† All typical values are at TA = 25°C.
TEST CONDITIONS
TA = MIN, 25°C
TA = MAX
TA = MIN to MAX
TA = MIN to MAX
No pullup
TL5001Q,
TL5001M
MIN TYP†
MAX
TL5001AQ,
TL5001AM
MIN TYP†
MAX
0.95
1.00
1.05
0.97
1.00
1.03
0.93
0.98
1.07
0.94
0.98
1.06
140
185
230
140
185
230
mV
60
120
60
120
mV
No pullup
TA = MIN to MAX
TA = MIN to MAX
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
UNIT
V
185
185
kΩ
1.5
1.5
V
9
TL5001, TL5001A
PULSE-WIDTH-MODULATION CONTROL CIRCUITS
SLVS084F – APRIL 1994 – REVISED JANUARY 2002
electrical characteristics over recommended operating free-air temperature range, VCC = 6 V,
fosc = 100 kHz (unless otherwise noted) (continued)
oscillator
PARAMETER
TEST CONDITIONS
Frequency
TL5001Q,
TL5001M
MIN TYP†
MAX
TL5001AQ,
TL5001AM
MIN TYP†
MAX
UNIT
100
100
kHz
2
2
kHz
1
1
kHz
TA = MIN to MAX
TA = MIN to MAX
Rt = 100 kΩ
Standard deviation of frequency
Frequency change with voltage
TA = MIN to MAX
Frequency change with
temperature
TA = MIN to MAX
VCC = 3.6 V to 40 V
Q suffix
*– 6
3
*6
*– 6
3
*6
M suffix
*– 9
5
*9
*– 9
5
*9
Voltage at RT
† All typical values are at TA = 25°C.
*Not production tested.
TA = MIN to MAX
1
1
kHz
V
dead-time control
PARAMETER
TEST CONDITIONS
Output (source)
current
TA = MIN to MAX
TA = 25°C
Input threshold
voltage
TA = MIN to MAX
V(DT) = 1.5 V
Duty cycle = 0%
TL5001Q, TL5001M
MIN
TYP†
MAX
0.9 × IRT‡
0.5
Duty cycle = 100%
Duty cycle = 0%
1.1 × IRT
0.7
1.3
0.4
Duty cycle = 100%
0.9 × IRT‡
1.1 × IRT
0.5
UNIT
µA
0.7
1.5
0.7
1.3
TL5001AQ, TL5001AM
MIN
TYP†
MAX
1.3
0.4
1.5
0.7
1.7
1.3
V
1.7
† All typical values are at TA = 25°C.
‡ Output source current at RT
error amplifier
PARAMETER
TL5001Q,
TL5001M
TEST CONDITIONS
MIN
Input bias current
Output
Out
ut
swing
voltage
TA = MIN to MAX
Positive
Negative
Open-loop voltage
amplification
Unity-gain bandwidth
Output (sink) current
Output (source) current
1.5
TA = MIN to MAX
TYP†
MAX
– 160
– 500
2.3
0.3
MIN
1.5
0.4
UNIT
TYP†
MAX
– 160
– 500
2.3
0.3
nA
V
0.4
V
TA = MIN to MAX
80
80
dB
TA = MIN to MAX
TA = MIN to MAX
1.5
1.5
MHz
µA
TA = MIN, 25°C
TA = MAX
VI(FB) = 1.2 V, COMP = 1 V
VI(FB) = 0
0.8
8 V,
V COMP = 1 V
100
600
100
600
– 45
– 70
– 45
– 70
– 30
– 45
– 30
– 45
† All typical values are at TA = 25°C.
10
TL5001AQ,
TL5001AM
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
µA
TL5001, TL5001A
PULSE-WIDTH-MODULATION CONTROL CIRCUITS
SLVS084F – APRIL 1994 – REVISED JANUARY 2002
electrical characteristics over recommended operating free-air temperature range, VCC = 6 V,
fosc = 100 kHz (unless otherwise noted) (continued)
output
PARAMETER
TL5001Q,
TL5001M
MIN TYP†
MAX
TL5001AQ,
TL5001AM
MIN TYP†
MAX
UNIT
IO = 10 mA
VO = 50 V, VCC = 0
VO = 50 V
1.5
1.5
V
VO = 6 V
40
TEST CONDITIONS
Output saturation voltage
TA = MIN to MAX
Off state current
Off-state
TA = MIN to MAX
Short-circuit output current
† All typical values are at TA = 25°C.
TA = MIN to MAX
2
2
10
10
10
10
40
µA
mA
total device
PARAMETER
TL5001Q,
TL5001M
TEST CONDITIONS
MIN
Standby supply current
Off state
Average supply current
† All typical values are at TA = 25°C.
TA = MIN to MAX
TA = MIN to MAX
Rt = 100 kΩ
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TL5001AQ,
TL5001AM
TYP†
MAX
1
1.4
UNIT
TYP†
MAX
1.5
1
1.5
mA
2.1
1.4
2.1
mA
MIN
11
TL5001, TL5001A
PULSE-WIDTH-MODULATION CONTROL CIRCUITS
SLVS084F – APRIL 1994 – REVISED JANUARY 2002
PARAMETER MEASUREMENT INFORMATION
2.3 V
COMP
1.5 V
DTC
OSC
PWM/DTC
Comparator
OUT
SCP
Comparator 1
1V
SCP
SCP Timing Period
SCP
Comparator 2
VCC
0V
3V
NOTE A: The waveforms show timing characteristics for an intermittent short circuit and a longer short circuit that is sufficient to activate SCP.
Figure 4. PWM Timing Diagram
12
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TL5001, TL5001A
PULSE-WIDTH-MODULATION CONTROL CIRCUITS
SLVS084F – APRIL 1994 – REVISED JANUARY 2002
TYPICAL CHARACTERISTICS
OSCILLATION FREQUENCY
vs
AMBIENT TEMPERATURE
OSCILLATOR FREQUENCY
vs
TIMING RESISTANCE
100
VCC = 6 V
DT Resistance = Rt
TA = 25°C
fosc – Oscillation Frequency – kHz
fosc – Oscillator Frequency – Hz
1M
100 k
10 k
10 k
100 k
VCC = 6 V
Rt = 100 kΩ
DT Resistance = 100 kΩ
98
96
94
92
90
88
– 50
1M
– 25
REFERENCE OUTPUT VOLTAGE
vs
POWER-SUPPLY VOLTAGE
∆V ref – Reference Output Voltage Fluctuation – %
V ref – Reference Output Voltage – V
1.6
1.4
1.2
1
0.8
0.6
0.4
0.2
0
0
1
2
3
4
5
50
75
100
REFERENCE OUTPUT VOLTAGE FLUCTUATION
vs
AMBIENT TEMPERATURE
TA = 25°C
FB and COMP
Connected Together
1.8
25
Figure 6
Figure 5
2
0
TA – Ambient Temperature – °C
Rt – Timing Resistance – Ω
6
7
8
9
10
VCC – Power-Supply Voltage – V
0.6
0.4
0.2
0
– 0.2
– 0.4
– 0.6
ÏÏÏÏÏÏÏÏÏÏÏÏ
ÏÏÏÏÏÏÏÏÏÏÏÏ
ÏÏÏÏÏÏÏÏÏÏÏÏ
ÏÏÏÏÏÏÏÏÏÏÏÏ
ÏÏÏÏÏÏÏÏÏÏÏÏ
ÏÏÏÏÏÏÏÏÏÏÏÏ
ÏÏÏÏÏÏÏÏÏÏÏÏ
ÏÏÏÏÏÏÏÏÏÏÏÏ
ÏÏÏÏÏÏÏÏÏÏÏÏ
ÏÏÏÏÏÏÏÏÏÏÏÏ
ÏÏÏÏÏÏÏÏÏÏÏÏ
– 0.8
– 50
VCC = 6 V
FB and COMP
Connected Together
– 25
0
25
50
75
TA – Ambient Temperature – °C
100
Figure 8
Figure 7
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
13
TL5001, TL5001A
PULSE-WIDTH-MODULATION CONTROL CIRCUITS
SLVS084F – APRIL 1994 – REVISED JANUARY 2002
TYPICAL CHARACTERISTICS
AVERAGE SUPPLY CURRENT
vs
POWER-SUPPLY VOLTAGE
AVERAGE SUPPLY CURRENT
vs
AMBIENT TEMPERATURE
2
1.3
I CC – Average Supply Current – mA
I CC – Average Supply Current – mA
Rt = 100 kΩ
TA = 25 °C
1.5
1
0.5
0
0
10
20
30
VCC = 6 V
Rt = 100 kΩ
DT Resistance = 100 kΩ
1.2
1.1
1
0.9
0.8
0
– 50
40
– 25
Figure 9
50
75
100
ERROR AMPLIFIER OUTPUT VOLTAGE
vs
OUTPUT (SINK) CURRENT
3
1.8
VCC = 6 V
TA = 25 °C
VO – Error Amplifier Output Voltage – V
PWM Triangle Wave Amplitude Voltage – V
25
Figure 10
PWM TRIANGLE WAVE AMPLITUDE VOLTAGE
vs
OSCILLATOR FREQUENCY
1.5
1.2
Voscmax (100% duty cycle)
0.9
Voscmin (zero duty cycle)
0.6
0.3
0
10 k
VCC = 6 V
VI(FB) = 1.2 V
TA = 25 °C
2.5
2
1.5
1
0.5
0
100 k
1M
fosc – Oscillator Frequency – Hz
10 M
0
0.2
Figure 12
POST OFFICE BOX 655303
0.4
IO – Output (Sink) Current – mA
Figure 11
14
0
TA – Ambient Temperature – °C
VCC – Power-Supply Voltage – V
• DALLAS, TEXAS 75265
0.6
TL5001, TL5001A
PULSE-WIDTH-MODULATION CONTROL CIRCUITS
SLVS084F – APRIL 1994 – REVISED JANUARY 2002
TYPICAL CHARACTERISTICS
ERROR AMPLIFIER OUTPUT VOLTAGE
vs
AMBIENT TEMPERATURE
ERROR AMPLIFIER OUTPUT VOLTAGE
vs
OUTPUT (SOURCE) CURRENT
2.46
VCC = 6 V
VI(FB) = 0.8 V
TA = 25 °C
2
1.5
1
0.5
60
80
100
20
40
IO – Output (Source) Current – µA
2.44
2.43
2.42
2.41
2.40
– 50
0
0
2.45
VCC = 6 V
VI(FB) = 0.8 V
No Load
120
25
50
75
– 25
0
TA – Ambient Temperature – °C
Figure 14
Figure 13
ERROR AMPLIFIER OPEN-LOOP GAIN AND
PHASE SHIFT
vs
FREQUENCY
ERROR AMPLIFIER OUTPUT VOLTAGE
vs
AMBIENT TEMPERATURE
40
VCC = 6 V
VI(FB) = 1.2 V
No Load
AV – Error Amplifier Open-Loop Gain – dB
VO – Error Amplifier Output Voltage – mV
240
220
100
200
180
160
140
120
– 50
– 25
0
25
50
75
TA – Ambient Temperature – °C
100
VCC = 6 V
TA = 25 °C
– 180°
30
– 210°
20
– 240°
AV
– 270°
10
0
φ
– 330°
– 10
– 20
10 k
– 300°
100 k
1M
Error Amplifier Open-Loop Phase Shift
2.5
VO – Error Amplifier Output Voltage – V
VO – Error Amplifier Output Voltage – V
3
– 360°
10 M
f – Frequency – Hz
Figure 15
Figure 16
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
15
TL5001, TL5001A
PULSE-WIDTH-MODULATION CONTROL CIRCUITS
SLVS084F – APRIL 1994 – REVISED JANUARY 2002
TYPICAL CHARACTERISTICS
OUTPUT DUTY CYCLE
vs
DTC VOLTAGE
SCP TIME-OUT PERIOD
vs
SCP CAPACITANCE
12
120
Output Duty Cycle – %
100
t SCP – SCP Time-Out Period – ms
VCC = 6 V
Rt = 100 kΩ
TA = 25 °C
80
60
40
20
VCC = 6 V
Rt = 100 kΩ
DT Resistance = 200 kΩ
TA = 25 °C
10
8
6
4
2
0
0
0
0.5
1.5
1
DTC Voltage – V
2
0
20
40
100
120
OUTPUT SATURATION VOLTAGE
vs
OUTPUT (SINK) CURRENT
DTC OUTPUT CURRENT
vs
RT OUTPUT CURRENT
2
– 60
VCC = 6 V
TA = 25 °C
DT Voltage = 1.3 V
TA = 25 °C
– 50
VCE – Output Saturation Voltage – V
IO(DT) – DTC Output Current – µ A
80
Figure 18
Figure 17
– 40
– 30
– 20
– 10
0
1.5
1
0.5
0
0
– 10
– 20
– 30
– 40
– 50
– 60
0
IO – RT Output Current – µA
Figure 19
16
60
CSCP – SCP Capacitance – nF
5
10
15
IO – Output (Sink) Current – mA
Figure 20
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
20
TL5001, TL5001A
PULSE-WIDTH-MODULATION CONTROL CIRCUITS
SLVS084F – APRIL 1994 – REVISED JANUARY 2002
APPLICATION INFORMATION
VI
5V
C1
100 µF
10 V
R1
470 Ω
+
Q1
TPS1101
GND
L1
20 µH
3.3 V
C3
0.1 µF
CR1
MBRS140T3
C2
100 µF
10 V
2
C4
1 µF
+
VCC
5
SCP
VO
C5
0.1 µF
R2
56 kΩ
R3
43 kΩ
COMP
1
7
GND
3
U1
TL5001/A
6
C6
0.012 µF
DTC
R5
7.50 kΩ
1%
FB
R7
2.0 kΩ
C7
0.0047 µF
R4
5.1 kΩ
4
RT
R6
3.24 kΩ
1%
GND
8
Partial Bill of Materials:
U1
TL5001/A
Q1
TPS1101
LI
CTX20-1 or
23 turns of #28 wire on
Micrometals No. T50-26B core
C1
TPSD107M010R0100
C2
TPSD107M010R0100
CR1
MBRS140T3
NOTES: A.
B.
C.
D.
+
Texas Instruments
Texas Instruments
Coiltronics
AVX
AVX
Motorola
Frequency = 200 kHz
Duty cycle = 90% max
Soft-start time constant (TC) = 5.6 ms
SCP TC = 70 msA
Figure 21. Step-Down Converter
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
17
TL5001, TL5001A
PULSE-WIDTH-MODULATION CONTROL CIRCUITS
SLVS084F – APRIL 1994 – REVISED JANUARY 2002
MECHANICAL DATA
D (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
14 PIN SHOWN
0.050 (1,27)
0.020 (0,51)
0.014 (0,35)
14
0.010 (0,25) M
8
0.008 (0,20) NOM
0.244 (6,20)
0.228 (5,80)
0.157 (4,00)
0.150 (3,81)
Gage Plane
0.010 (0,25)
1
7
0°– 8°
A
0.044 (1,12)
0.016 (0,40)
Seating Plane
0.069 (1,75) MAX
0.010 (0,25)
0.004 (0,10)
PINS **
0.004 (0,10)
8
14
16
A MAX
0.197
(5,00)
0.344
(8,75)
0.394
(10,00)
A MIN
0.189
(4,80)
0.337
(8,55)
0.386
(9,80)
DIM
4040047 / D 10/96
NOTES: B.
C.
D.
E.
18
All linear dimensions are in inches (millimeters).
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion, not to exceed 0.006 (0,15).
Falls within JEDEC MS-012
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TL5001, TL5001A
PULSE-WIDTH-MODULATION CONTROL CIRCUITS
SLVS084F – APRIL 1994 – REVISED JANUARY 2002
MECHANICAL DATA
FK (S-CQCC-N**)
LEADLESS CERAMIC CHIP CARRIER
28 TERMINALS SHOWN
18
17
16
15
14
13
NO. OF
TERMINALS
**
12
19
11
20
10
A
B
MIN
MAX
MIN
MAX
20
0.342
(8,69)
0.358
(9,09)
0.307
(7,80)
0.358
(9,09)
28
0.442
(11,23)
0.458
(11,63)
0.406
(10,31)
0.458
(11,63)
21
9
22
8
44
0.640
(16,26)
0.660
(16,76)
0.495
(12,58)
0.560
(14,22)
23
7
52
0.740
(18,78)
0.761
(19,32)
0.495
(12,58)
0.560
(14,22)
24
6
68
25
5
0.938
(23,83)
0.962
(24,43)
0.850
(21,6)
0.858
(21,8)
84
1.141
(28,99)
1.165
(29,59)
1.047
(26,6)
1.063
(27,0)
B SQ
A SQ
26
27
28
1
2
3
4
0.080 (2,03)
0.064 (1,63)
0.020 (0,51)
0.010 (0,25)
0.020 (0,51)
0.010 (0,25)
0.055 (1,40)
0.045 (1,14)
0.045 (1,14)
0.035 (0,89)
0.045 (1,14)
0.035 (0,89)
0.028 (0,71)
0.022 (0,54)
0.050 (1,27)
4040140 / C 11/95
NOTES: A.
B.
C.
D.
E.
All linear dimensions are in inches (millimeters).
This drawing is subject to change without notice.
This package can be hermetically sealed with a metal lid.
The terminals are gold-plated.
Falls within JEDEC MS-004
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
19
MECHANICAL DATA
MCER001A – JANUARY 1995 – REVISED JANUARY 1997
MECHANICAL DATA
JG (R-GDIP-T8)
CERAMIC DUAL-IN-LINE
0.400 (10,16)
0.355 (9,00)
8
5
0.280 (7,11)
0.245 (6,22)
1
0.063 (1,60)
0.015 (0,38)
4
0.065 (1,65)
0.045 (1,14)
0.310 (7,87)
0.290 (7,37)
0.020 (0,51) MIN
0.200 (5,08) MAX
Seating Plane
0.130 (3,30) MIN
0.023 (0,58)
0.015 (0,38)
0°–15°
0.100 (2,54)
0.014 (0,36)
0.008 (0,20)
4040107/C 08/96
NOTES: A.
B.
C.
D.
E.
20
All linear dimensions are in inches (millimeters).
This drawing is subject to change without notice.
This package can be hermetically sealed with a ceramic lid using glass frit.
Index point is provided on cap for terminal identification.
Falls within MIL STD 1835 GDIP1-T8
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MECHANICAL DATA
MCER001A – JANUARY 1995 – REVISED JANUARY 1997
MECHANICAL INFORMATION
P (R-PDIP-T8)
PLASTIC DUAL-IN-LINE PACKAGE
0.400 (10,60)
0.355 (9,02)
8
5
0.260 (6,60)
0.240 (6,10)
1
4
0.070 (1,78) MAX
0.310 (7,87)
0.290 (7,37)
0.020 (0,51) MIN
0.200 (5,08) MAX
Seating Plane
0.125 (3,18) MIN
0.100 (2,54)
0.021 (0,53)
0.015 (0,38)
0°– 15°
0.010 (0,25) M
0.010 (0,25) NOM
4040082 / B 03/95
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-001
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
21
PACKAGE OPTION ADDENDUM
www.ti.com
14-Feb-2008
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
5962-9958301Q2A
ACTIVE
LCCC
FK
20
1
TBD
5962-9958301QPA
ACTIVE
CDIP
JG
8
1
TBD
Lead/Ball Finish
MSL Peak Temp (3)
POST-PLATE N / A for Pkg Type
A42 SNPB
N / A for Pkg Type
5962-9958302Q2A
ACTIVE
LCCC
FK
20
1
TBD
5962-9958302QPA
ACTIVE
CDIP
JG
8
1
TBD
POST-PLATE N / A for Pkg Type
A42 SNPB
TL5001ACD
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TL5001ACDG4
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TL5001ACDR
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TL5001ACDRG4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TL5001ACP
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
TL5001ACPE4
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
TL5001AID
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TL5001AIDG4
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TL5001AIDR
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TL5001AIDRG4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TL5001AIP
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
TL5001AIPE4
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
TL5001AMFKB
ACTIVE
LCCC
FK
20
1
TBD
N / A for Pkg Type
POST-PLATE N / A for Pkg Type
TL5001AMJG
ACTIVE
CDIP
JG
8
1
TBD
A42 SNPB
N / A for Pkg Type
TL5001AMJGB
ACTIVE
CDIP
JG
8
1
TBD
A42 SNPB
N / A for Pkg Type
TL5001AQD
ACTIVE
SOIC
D
8
75
TBD
CU NIPDAU
Level-1-220C-UNLIM
TL5001AQDG4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
CU NIPDAU
Level-1-220C-UNLIM
CU NIPDAU
Level-1-260C-UNLIM
TL5001AQDR
ACTIVE
SOIC
D
8
2500
TL5001AQDRG4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
TL5001CD
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TL5001CDG4
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TL5001CDR
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TL5001CDRG4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TL5001CP
ACTIVE
PDIP
P
8
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
TL5001CP-P
OBSOLETE
PDIP
P
8
Pb-Free
CU NIPDAU
N / A for Pkg Type
50
Addendum-Page 1
TBD
PACKAGE OPTION ADDENDUM
www.ti.com
14-Feb-2008
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TL5001CPE4
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
TL5001CPS
ACTIVE
SO
PS
8
80
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TL5001CPSG4
ACTIVE
SO
PS
8
80
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TL5001CPSLE
OBSOLETE
SO
PS
8
TL5001CPSR
ACTIVE
SO
PS
8
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TL5001CPSRG4
ACTIVE
SO
PS
8
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TL5001ID
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TL5001IDG4
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TL5001IDR
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TL5001IDRG4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TL5001IP
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
TL5001IPE4
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
TL5001MFKB
ACTIVE
LCCC
FK
20
1
TBD
TL5001MJG
ACTIVE
CDIP
JG
8
1
TBD
TL5001MJGB
ACTIVE
CDIP
JG
8
1
TL5001QD
ACTIVE
SOIC
D
8
75
TL5001QDG4
ACTIVE
SOIC
D
8
TL5001QDR
ACTIVE
SOIC
D
TL5001QDRG4
ACTIVE
SOIC
D
Lead/Ball Finish
MSL Peak Temp (3)
(RoHS)
TBD
Call TI
Call TI
POST-PLATE N / A for Pkg Type
A42 SNPB
N / A for Pkg Type
TBD
A42 SNPB
N / A for Pkg Type
TBD
CU NIPDAU
Level-1-220C-UNLIM
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
8
2500
TBD
CU NIPDAU
Level-1-220C-UNLIM
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
Addendum-Page 2
PACKAGE OPTION ADDENDUM
www.ti.com
14-Feb-2008
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
19-Mar-2008
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
Diameter Width
(mm) W1 (mm)
A0 (mm)
B0 (mm)
K0 (mm)
P1
(mm)
W
Pin1
(mm) Quadrant
TL5001ACDR
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
TL5001AIDR
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
TL5001CDR
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
TL5001CPSR
SO
PS
8
2000
330.0
16.4
8.2
6.6
2.5
12.0
16.0
Q1
TL5001IDR
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
19-Mar-2008
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TL5001ACDR
SOIC
D
8
2500
340.5
338.1
20.6
TL5001AIDR
SOIC
D
8
2500
340.5
338.1
20.6
TL5001CDR
SOIC
D
8
2500
340.5
338.1
20.6
TL5001CPSR
SO
PS
8
2000
346.0
346.0
33.0
TL5001IDR
SOIC
D
8
2500
340.5
338.1
20.6
Pack Materials-Page 2
MECHANICAL DATA
MLCC006B – OCTOBER 1996
FK (S-CQCC-N**)
LEADLESS CERAMIC CHIP CARRIER
28 TERMINAL SHOWN
18
17
16
15
14
13
NO. OF
TERMINALS
**
12
19
11
20
10
A
B
MIN
MAX
MIN
MAX
20
0.342
(8,69)
0.358
(9,09)
0.307
(7,80)
0.358
(9,09)
28
0.442
(11,23)
0.458
(11,63)
0.406
(10,31)
0.458
(11,63)
21
9
22
8
44
0.640
(16,26)
0.660
(16,76)
0.495
(12,58)
0.560
(14,22)
23
7
52
0.739
(18,78)
0.761
(19,32)
0.495
(12,58)
0.560
(14,22)
24
6
68
0.938
(23,83)
0.962
(24,43)
0.850
(21,6)
0.858
(21,8)
84
1.141
(28,99)
1.165
(29,59)
1.047
(26,6)
1.063
(27,0)
B SQ
A SQ
25
5
26
27
28
1
2
3
4
0.080 (2,03)
0.064 (1,63)
0.020 (0,51)
0.010 (0,25)
0.020 (0,51)
0.010 (0,25)
0.055 (1,40)
0.045 (1,14)
0.045 (1,14)
0.035 (0,89)
0.045 (1,14)
0.035 (0,89)
0.028 (0,71)
0.022 (0,54)
0.050 (1,27)
4040140 / D 10/96
NOTES: A.
B.
C.
D.
E.
All linear dimensions are in inches (millimeters).
This drawing is subject to change without notice.
This package can be hermetically sealed with a metal lid.
The terminals are gold plated.
Falls within JEDEC MS-004
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MECHANICAL DATA
MPDI001A – JANUARY 1995 – REVISED JUNE 1999
P (R-PDIP-T8)
PLASTIC DUAL-IN-LINE
0.400 (10,60)
0.355 (9,02)
8
5
0.260 (6,60)
0.240 (6,10)
1
4
0.070 (1,78) MAX
0.325 (8,26)
0.300 (7,62)
0.020 (0,51) MIN
0.015 (0,38)
Gage Plane
0.200 (5,08) MAX
Seating Plane
0.010 (0,25) NOM
0.125 (3,18) MIN
0.100 (2,54)
0.021 (0,53)
0.015 (0,38)
0.430 (10,92)
MAX
0.010 (0,25) M
4040082/D 05/98
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-001
For the latest package information, go to http://www.ti.com/sc/docs/package/pkg_info.htm
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MECHANICAL DATA
MCER001A – JANUARY 1995 – REVISED JANUARY 1997
JG (R-GDIP-T8)
CERAMIC DUAL-IN-LINE
0.400 (10,16)
0.355 (9,00)
8
5
0.280 (7,11)
0.245 (6,22)
1
0.063 (1,60)
0.015 (0,38)
4
0.065 (1,65)
0.045 (1,14)
0.310 (7,87)
0.290 (7,37)
0.020 (0,51) MIN
0.200 (5,08) MAX
Seating Plane
0.130 (3,30) MIN
0.023 (0,58)
0.015 (0,38)
0°–15°
0.100 (2,54)
0.014 (0,36)
0.008 (0,20)
4040107/C 08/96
NOTES: A.
B.
C.
D.
E.
All linear dimensions are in inches (millimeters).
This drawing is subject to change without notice.
This package can be hermetically sealed with a ceramic lid using glass frit.
Index point is provided on cap for terminal identification.
Falls within MIL STD 1835 GDIP1-T8
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DSP
Clocks and Timers
Interface
Logic
Power Mgmt
Microcontrollers
RFID
RF/IF and ZigBee® Solutions
amplifier.ti.com
dataconverter.ti.com
dsp.ti.com
www.ti.com/clocks
interface.ti.com
logic.ti.com
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/lprf
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Military
Optical Networking
Security
Telephony
Video & Imaging
Wireless
www.ti.com/audio
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/medical
www.ti.com/military
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2008, Texas Instruments Incorporated