INFINEON TLE6250_08

Data Sheet, Rev. 4.0, April 2008
TLE6250
High Speed CAN-Transceiver
Automotive Power
Edition 2008-04-28
Published by
Infineon Technologies AG
81726 Munich, Germany
© 2004 Infineon Technologies AG
All Rights Reserved.
Legal Disclaimer
The information given in this document shall in no event be regarded as a guarantee of conditions or
characteristics. With respect to any examples or hints given herein, any typical values stated herein and/or any
information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties
and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights
of any third party.
Information
For further information on technology, delivery terms and conditions and prices, please contact the nearest
Infineon Technologies Office (www.infineon.com).
Warnings
Due to technical requirements, components may contain dangerous substances. For information on the types in
question, please contact the nearest Infineon Technologies Office.
Infineon Technologies components may be used in life-support devices or systems only with the express written
approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure
of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support
devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain
and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may
be endangered.
High Speed CAN-Transceiver
TLE6250
Features
•
•
•
•
•
•
•
•
•
•
CAN data transmission rate up to 1 MBaud
Receive-only Mode and Stand-by Mode
Suitable for 12 V and 24 V applications
Excellent EMC performance (very high immunity and
very low emission)
Version for 5 V and 3.3 V microcontrollers
Bus pins are short circuit proof to ground and battery
voltage
Overtemperature protection
Very wide temperature range (-40 °C up to 150 °C)
Green Product (RoHS compliant)
AEC Qualified
Description
The HS CAN-transceiver family TLE6250 (TLE6250G and TLE6250GV33) are
monolithic integrated circuits that are available as bare die as well as in a PG-DSO-8
package. The ICs are optimized for high speed differential mode data transmission in
automotive and industrial applications and they are compatible to ISO/DIS 11898. They
work as an interface between the CAN protocol controller and the physical differential
bus in both, 12 V and 24 V systems.
The ICs are based on the Smart Power Technology SPT® which allows bipolar and
CMOS control circuitry in accordance with DMOS power devices existing on the same
monolithic circuit. The TLE6250G is designed to withstand the severe conditions of
automotive applications and provides excellent EMC performance.
Note: There are two versions available (refer to next page).
Type
Package
TLE6250G
PG-DSO-8
TLE6250C
(chip)
TLE6250GV33
PG-DSO-8
TLE6250CV33
(chip)
Data Sheet
3
Rev. 4.0, 2008-04-28
TLE6250
TLE6250G
5 V logic I/O version: RxD, TxD, INH, RM. Two Control pins (RM, INH) and 3 operation
modes: Normal Mode, Stand-by Mode and Receive Only Mode.
TLE6250GV33
3.3 V logic I/O version (logic I/O voltage adaptive to V33 pin within the range 3.3 V to 5 V):
RxD, TxD, INH. One control pin (INH) and two operation modes: Normal Mode and
Standby Mode.
Pin Configuration
T L E6250 G
T xD
1
8
IN H
GN D
2
7
C AN H
V CC
3
6
C AN L
R xD
4
5
RM
AEP03320.VSD
Figure 1
Pin Configuration TLE6250G (top view)
T LE6250GV 33
T xD
1
8
IN H
GN D
2
7
C AN H
V CC
3
6
C AN L
R xD
4
5
V 33 V
AEP03321.VSD
Figure 2
Data Sheet
Pin Configuration TLE6250GV33 (top view)
4
Rev. 4.0, 2008-04-28
TLE6250
Table 1
Pin Definitions and Functions TLE6250G
Pin No.
Symbol Function
1
TxD
CAN transmit data input; 20 kΩ pull-up, LOW in dominant state
2
GND
Ground
3
VCC
5 V Supply input
4
RxD
CAN receive data output; LOW in dominant state,
integrated pull-up
5
RM
Receive-only input; control input, 20 kΩ pull-up, set low to
activate RxD-only mode
6
CANL
Low line I/O; LOW in dominant state
7
CANH
High line I/O; HIGH in dominant state
8
INH
Inhibit Input; control input, 20 kΩ pull, set LOW for normal mode
Table 2
Pin Definitions and Functions TLE6250GV33
Pin No.
Symbol Function
1
TxD
CAN transmit data input; 20 kΩ pull-up, LOW in dominant state
2
GND
Ground
3
VCC
5 V Supply input
4
RxD
CAN receive data output; LOW in dominant state,
integrated pull-up
5
V33V
Logic supply input; 3.3 V OR 5 V microcontroller logic supply can
be connected here! The digital I/Os of the TLE6250GV33 adopt to
the connected microcontroller logic supply at V33V
6
CANL
Low line I/O; LOW in dominant state
7
CANH
High line I/O; HIGH in dominant state
8
INH
Inhibit Input; control input, 20 kΩ pull, set LOW for normal mode
Data Sheet
5
Rev. 4.0, 2008-04-28
TLE6250
Functional Block Diagram
TL E6250 G
C AN H
C AN L
3
7
6
D river
Output
Stage
1
T em pProtection
M ode C ontrol
8
5
VCC
T xD
IN H
RM
=
R eceiver
*
GN D
2
4
R xD
AEA 03311.VSD
Figure 3
Data Sheet
Block Diagram TLE6250G
6
Rev. 4.0, 2008-04-28
TLE6250
TL E6250 GV33
3
5
C AN H
C AN L
7
6
D river
Output
Stage
1
T em pProtection
M ode C ontrol
8
VCC
V33
T xD
IN H
=
R eceiver
*
GN D
2
4
R xD
AEA 03312.VSD
Figure 4
Data Sheet
Block Diagram TLE6250GV33
7
Rev. 4.0, 2008-04-28
TLE6250
Application Information
TLE6250G
Normal Mode
INH = 1
INH = 0
RM = 1
INH = 0
and RM = 1
RM = 1
INH = 0
and RM = 0
Stand-by Mode
INH = 1
RM = 0
Receive-only Mode
INH = 1
RM = 0 / 1
INH = 0
RM = 0
AED02924
Normal Mode
INH = 0
INH = 1
INH = 0
Stand-by
Mode
INH = 1
AEA03327.VSD
TLE6250GV33
Figure 5
Mode State Diagram
Both, the TLE6250G as well as the TLE6250C offer three different operation modes (see
Figure 5), controlled by the INH and RM pin. The TLE6250GV33 offers only two modes,
controlled by the INH (GV33) pin respectively.
Data Sheet
8
Rev. 4.0, 2008-04-28
TLE6250
In the normal mode the device is able to receive and to transmit messages whereas in
the receive-only mode signals at the TxD input are not transmitted to the CAN bus. The
receive-only mode can be used for diagnostic purposes (to check the bus connections
between the nodes) as well as to prevent the bus being blocked by a faulty permanent
dominant TxD input signal. The stand-by mode is a low power mode that disables both,
the receiver as well as the transmitter.
In case the receive-only feature is not used the RM pin has to be left open. When the
stand-by mode is not used the INH pin has to be connected to ground level in order to
switch the TLE6250G in normal mode.
Application Information for the 3.3 V Versions
The TLE6250GV33 can be used for both; 3.3 V and 5 V microcontroller logic supply, as
shown in Figure 6. Don’t apply external resistors between the power supply and this pin.
This may cause a voltage drop and so reduce the available voltage at this pin.
Data Sheet
9
Rev. 4.0, 2008-04-28
TLE6250
Application with 3.3 V I/O supply
TL E6250 GV 33
IN H
7
6
RxD
C AN H
Tx D
C AN L
4
1
3
V CC
100
nF
2
e. g. TLE 4476
100
nF
3 .3 V
VQ 2
+
22
µF
100
nF
GN D
100
nF
5V
VQ 1
VI
µP
3 .3 V
5
V 33 V
GN D
8
+
GN D
22 µF
+
22 µF
AEA 03300.VSD
Application with 5 V I/O supply
T L E6250 GV 33
IN H
7
6
R xD
C AN H
T xD
C AN L
V 33 V
GN D
V CC
8
4
1
5
µP
5V
3
100
nF
2
100
nF
GN D
e. g. T LE 4270
VI
+
22
µF
100
nF
VQ
5V
+
GN D
22 µF
AEA 03299.VSD
Figure 6
Data Sheet
Application Circuits TLE6250GV33 Used for 3.3 V and 5 V Logic
10
Rev. 4.0, 2008-04-28
TLE6250
Application with separate 5V power supplies,
for applications with switchable transceiver supply
TL E6250 GV 33
IN H
7
6
R xD
C AN H
TxD
C AN L
V 33 V
GN D
V CC
8
4
1
5
µP
5V
3
100
nF
100
nF
2
GN D
e. g. T LE 4270
VI
+
22
µF
100
nF
VQ
5V +
GN D
22 µF
e. g. T LE 4270
VI
+
22
µF
100
nF
VQ
5V
GN D
+
AEA 13299.VSD
Figure 6 (cont.) Application Circuits TLE6250GV33 Used for 3.3 V and 5 V Logic
Data Sheet
11
Rev. 4.0, 2008-04-28
TLE6250
Electrical Characteristics TLE6250G (5 V version)
Table 3
Absolute Maximum Ratings
Parameter
Symbol
Limit Values
Unit
Remarks
Min.
Max.
VCC
VCANH/L
-0.3
6.5
V
–
-40
40
V
–
Logic voltages at INH, RM,
TxD, RxD
VI
-0.3
VCC
V
0 V < VCC < 5.5 V
Electrostatic discharge
voltage at CANH, CANL
VESD
-6
6
kV
human body model
(100 pF via 1.5 kΩ)
Electrostatic discharge
voltage
VESD
-2
2
kV
human body model
(100 pF via 1.5 kΩ)
Tj
-40
160
°C
–
Voltages
Supply voltage
CAN input voltage (CANH,
CANL)
Temperatures
Junction temperature
Note: Maximum ratings are absolute ratings; exceeding any one of these values may
cause irreversible damage to the integrated circuit.
Table 4
Operating Range
Parameter
Symbol
Limit Values
Min.
Supply voltage
Junction temperature
Unit
Remarks
Max.
VCC
Tj
4.5
5.5
V
–
-40
150
°C
–
Rthj-a
–
185
K/W
–
200
°C
10 °C hysteresis
Thermal Resistances
Junction ambient
Thermal Shutdown (junction temperature)
Thermal shutdown
temperature
Data Sheet
TjsD
160
12
Rev. 4.0, 2008-04-28
TLE6250
Table 5
Electrical Characteristics
4.5 V < VCC < 5.5 V; RL = 60 Ω; VINH < VINH,ON; -40 °C < Tj < 150 °C; all voltages with
respect to ground; positive current flowing into pin; unless otherwise specified.
Parameter
Symbol
Limit Values
Unit Remarks
Min. Typ. Max.
Current Consumption
Current consumption
ICC
–
6
10
mA
recessive state;
VTxD = VCC
Current consumption
ICC
–
45
70
mA
dominant state;
VTxD = 0 V
Current consumption
ICC
–
6
10
mA
receive-only mode;
RM = low
Current consumption
ICC,stb
–
1
10
µA
stand-by mode;
TxD = RM = high
HIGH level output current
IRD,H
–
-4
-2
mA
LOW level output current
IRD,L
2
4
–
mA
VRD = 0.8 × VCC,
Vdiff < 0.4 V1)
VRD = 0.2 × VCC,
Vdiff > 1 V1)
HIGH level input voltage
threshold
VTD,H
–
0.5 × 0.7 × V
LOW level input voltage
threshold
VTD,L
TxD pull-up resistance
Receiver Output RxD
Transmission Input TxD
VCC
recessive state
VCC
0.3 × 0.4 × –
V
dominant state
kΩ
–
VCC
VCC
RTD
10
25
HIGH level input voltage
threshold
VINH,H
–
0.5 × 0.7 × V
LOW level input voltage
threshold
VINH,L
INH pull-up resistance
RINH
50
Inhibit Input (pin INH)
Data Sheet
VCC
0.3 × 0.4 × –
VCC
VCC
10
25
13
stand-by mode;
VCC
50
V
normal mode
kΩ
–
Rev. 4.0, 2008-04-28
TLE6250
Table 5
Electrical Characteristics (cont’d)
4.5 V < VCC < 5.5 V; RL = 60 Ω; VINH < VINH,ON; -40 °C < Tj < 150 °C; all voltages with
respect to ground; positive current flowing into pin; unless otherwise specified.
Parameter
Symbol
Limit Values
Unit Remarks
Min. Typ. Max.
Receive only Input (pin RM) (5 V version only)
HIGH level input voltage
threshold
VRM,H
LOW level input voltage
threshold
VRM,L
RM pull-up resistance
–
0.5 × 0.7 × V
VCC
normal mode;
VCC
0.3 × 0.4 × –
V
receive-only mode
kΩ
–
VCC
VCC
RRM
10
25
Differential receiver
threshold voltage,
recessive to dominant
edge
Vdiff,d
–
0.75 0.90 V
Differential receiver
threshold voltage
dominant to recessive
edge
Vdiff,r
0.50 0.60 –
V
-20 V < (VCANH, VCANL)
< 25 V
Vdiff = VCANH - VCANL
Common Mode Range
CMR
-20
–
25
V
VCC = 5 V
Differential receiver
hysteresis
Vdiff,hys
–
150
–
mV
–
CANH, CANL input
resistance
Ri
10
20
30
kΩ
recessive state
Differential input
resistance
Rdiff
20
40
60
kΩ
recessive state
50
Bus Receiver
Data Sheet
14
-20 V < (VCANH, VCANL)
< 25 V
Vdiff = VCANH - VCANL
Rev. 4.0, 2008-04-28
TLE6250
Table 5
Electrical Characteristics (cont’d)
4.5 V < VCC < 5.5 V; RL = 60 Ω; VINH < VINH,ON; -40 °C < Tj < 150 °C; all voltages with
respect to ground; positive current flowing into pin; unless otherwise specified.
Parameter
Symbol
Limit Values
Unit Remarks
Min. Typ. Max.
Bus Transmitter
0.4 × –
0.6 × V
VCC
VCC
CANL/CANH recessive
output voltage
VCANL/H
CCANH, CANL recessive
output voltage difference
Vdiff = VCANH - VCANL, no
load2)
Vdiff
-1
–
0.05 V
VTxD = VCC
CANL dominant output
voltage
VCANL
–
–
2.0
V
CANH dominant output
voltage
VCANH
2.8
–
–
V
CANH, CANL dominant
output voltage difference
Vdiff = VCANH - VCANL
Vdiff
1.5
–
3.0
V
VTxD = 0 V;
VCC = 5 V
VTxD = 0 V;
VCC = 5 V
VTxD = 0 V;
VCC = 5 V
CANL short circuit current ICANLsc
50
120
200
mA
–
150
–
mA
CANH short circuit current ICANHsc
-200 -120 -50
mA
CANH short circuit current ICANHsc
–
-120 –
mA
-50
-300 -400 µA
-50
-100 -150 µA
50
280
400
µA
50
100
150
µA
Output current
Output current
Data Sheet
ICANH,lk
ICANH,lk
15
VTxD = VCC
VCANLshort = 18 V
VCANLshort = 36 V
VCANHshort = 0 V
VCANHshort = -5 V
VCC = 0 V,
VCANH = VCANL = -7 V
VCC = 0 V,
VCANH = VCANL = -2 V
VCC = 0 V,
VCANH = VCANL = 7 V
VCC = 0 V,
VCANH = VCANL = 2 V
Rev. 4.0, 2008-04-28
TLE6250
Table 5
Electrical Characteristics (cont’d)
4.5 V < VCC < 5.5 V; RL = 60 Ω; VINH < VINH,ON; -40 °C < Tj < 150 °C; all voltages with
respect to ground; positive current flowing into pin; unless otherwise specified.
Parameter
Symbol
Limit Values
Unit Remarks
Min. Typ. Max.
Dynamic CAN-Transceiver Characteristics
Propagation delay TxD-to- td(L),TR
RxD LOW (recessive to
dominant)
–
150
280
ns
Propagation delay TxD-to- td(H),TR
RxD HIGH (dominant to
recessive)
–
150
280
ns
Propagation delay TxD
LOW to bus dominant
td(L),T
–
100
140
ns
Propagation delay TxD
HIGH to bus recessive
td(H),T
–
100
140
ns
Propagation delay bus
dominant to RxD LOW
td(L),R
–
50
140
ns
Propagation delay bus
recessive to RxD HIGH
td(H),R
–
50
140
ns
CL = 47 pF;
RL = 60 Ω;
VCC = 5 V;
CRxD = 20 pF
CL = 47 pF;
RL = 60 Ω;
VCC = 5 V;
CRxD = 20 pF
CL = 47 pF;
RL = 60 Ω;
VCC = 5 V
CL = 47 pF;
RL = 60 Ω;
VCC = 5 V
CL = 47 pF;
RL = 60 Ω;
VCC = 5 V;
CRxD = 20 pF
CL = 47 pF;
RL = 60 Ω;
VCC = 5 V;
CRxD = 20 pF
1) Vdiff = VCANH - VCANL
2) Deviation from ISO/DIS 11898
Data Sheet
16
Rev. 4.0, 2008-04-28
TLE6250
Electrical Characteristics TLE6250GV33 (3.3 V version)
Table 6
Absolute Maximum Ratings
Parameter
Symbol
Limit Values
Min.
Max.
VCC
V33V
VCANH/L
-0.3
6.5
Logic voltages at INH, RM,
TxD, RxD
Unit
Remarks
V
–
Voltages
Supply voltage
3.3 V supply
-0.3
6.5
V
–
-40
40
V
–
VI
-0.3
VCC
V
0 V < VCC < 5.5 V
Electrostatic discharge
voltage at CANH, CANL
VESD
-6
6
kV
human body model
(100 pF via 1.5 kΩ)
Electrostatic discharge
voltage
VESD
-2
2
kV
human body model
(100 pF via 1.5 kΩ)
Tj
-40
160
°C
–
CAN input voltage (CANH,
CANL)
Temperatures
Junction temperature
Note: Maximum ratings are absolute ratings; exceeding any one of these values may
cause irreversible damage to the integrated circuit.
Table 7
Operating Range
Parameter
Symbol
Min.
Max.
Supply voltage
VCC
V33V
Tj
4.5
5.5
Rthj-a
3.3 V supply voltage
Junction temperature
Limit Values
Unit
Remarks
V
–
3.0
5.5
V
–
-40
150
°C
–
–
185
K/W
–
200
°C
10 °C hysteresis
Thermal Resistances
Junction ambient
Thermal Shutdown (junction temperature)
Thermal shutdown
temperature
Data Sheet
TjsD
160
17
Rev. 4.0, 2008-04-28
TLE6250
Table 8
Electrical Characteristics
4.5 V < VCC < 5.5 V; (3.0 V < V33V < 5.5V for 3.3 V version); RL = 60 Ω; VINH < VINH,ON;
-40 °C < Tj < 150 °C; all voltages with respect to ground; positive current flowing into pin;
unless otherwise specified.
Parameter
Symbol
Limit Values
Min.
Typ.
Max.
6
10
Unit Remarks
Current Consumption (3.3 V version)
Current consumption
ICC+33V
–
mA
recessive state;
VTxD = V33V
Current consumption
ICC+33V
Current consumption
45
70
mA
dominant state;
VTxD = 0 V
I33V
–
ICC+33V,stb –
–
2
mA
–
1
10
µA
stand-by mode,
TxD = high
HIGH level output
current
IRD,H
–
-2
-1
mA
LOW level output
current
IRD,L
1
2
–
mA
VRD = 0.8 × V33V,
Vdiff < 0.4 V1)
VRD = 0.2 × V33V,
Vdiff > 1 V1)
Current consumption
–
Receiver Output RxD
Transmission Input TxD
HIGH level input
voltage threshold
VTD,H
LOW level input
voltage threshold
VTD,L
–
0.55 × 0.7 ×
V33V
TxD pull-up resistance RTD
V
recessive state
V
dominant state
kΩ
–
V
stand-by mode;
V
normal mode;
kΩ
–
V33V
0.3 ×
0.45 × –
V33V
V33V
10
25
50
Inhibit Input (pin INH)
HIGH level input
voltage threshold
VINH,H
LOW level input
voltage threshold
VINH,L
0.55 × 0.7 ×
V33V
INH pull-up resistance RINH
Data Sheet
–
V33V
0.3 ×
0.45 × –
V33V
V33V
10
25
18
50
Rev. 4.0, 2008-04-28
TLE6250
Table 8
Electrical Characteristics (cont’d)
4.5 V < VCC < 5.5 V; (3.0 V < V33V < 5.5V for 3.3 V version); RL = 60 Ω; VINH < VINH,ON;
-40 °C < Tj < 150 °C; all voltages with respect to ground; positive current flowing into pin;
unless otherwise specified.
Parameter
Symbol
Limit Values
Unit Remarks
Min.
Typ.
Max.
Differential receiver
Vdiff,d
threshold voltage,
recessive to dominant
edge
–
0.75
0.90
V
-20 V < (VCANH, VCANL)
< 25 V
Vdiff = VCANH - VCANL
Differential receiver
Vdiff,r
threshold voltage,
dominant to recessive
edge
0.50
0.60
–
V
-20 V < (VCANH, VCANL)
< 25 V
Vdiff = VCANH - VCANL
Common Mode Range CMR
-20
–
25
V
VCC = 5 V
Bus Receiver
Differential receiver
hysteresis
Vdiff,hys
–
150
–
mV
–
CANH, CANL input
resistance
Ri
10
20
30
kΩ
recessive state
Differential input
resistance
Rdiff
20
40
60
kΩ
recessive state
Data Sheet
19
Rev. 4.0, 2008-04-28
TLE6250
Table 8
Electrical Characteristics (cont’d)
4.5 V < VCC < 5.5 V; (3.0 V < V33V < 5.5V for 3.3 V version); RL = 60 Ω; VINH < VINH,ON;
-40 °C < Tj < 150 °C; all voltages with respect to ground; positive current flowing into pin;
unless otherwise specified.
Parameter
Symbol
Limit Values
Min.
Typ.
Max.
0.4 ×
–
0.6 ×
Unit Remarks
Bus Transmitter
CANL/CANH
recessive output
voltage
VCANL/H
V
VTxD = V33V
CANH, CANL
recessive output
voltage difference
Vdiff = VCANH - VCANL,
no load2)
Vdiff
-1
–
0.05
V
VTxD = V33V
CANL dominant
output voltage
VCANL
–
–
2.0
V
2.8
–
–
V
Vdiff
1.5
–
3.0
V
VTxD = 0 V;
VCC = 5 V
VTxD = 0 V;
VCC = 5 V
VTxD = 0 V;
VCC = 5 V
CANH dominant
output voltage
VCANH
CANH, CANL
dominant output
voltage difference
Vdiff = VCANH - VCANL
CANL short circuit
current
ICANLsc
50
120
200
mA
–
150
–
mA
CANH short circuit
current
ICANHsc
-200
-120
-50
mA
VCANLshort = 18 V
VCANLshort = 36 V
VCANHshort = 0 V
CANH short circuit
current
ICANHsc
–
-120
–
mA
VCANHshort = -5 V
Output current
ICANH/L,lk
-50
-300
-400
µA
-50
-100
-150
µA
50
280
400
µA
50
100
150
µA
VCC = 0 V,
VCANH = VCANL = -7 V
VCC = 0 V,
VCANH =VCANL = -2 V
VCC = 0 V,
VCANH = VCANL = 7 V
VCC = 0 V,
VCANH = VCANL = 2 V
Output current
Data Sheet
VCC
ICANH/L,lk
VCC
20
Rev. 4.0, 2008-04-28
TLE6250
Table 8
Electrical Characteristics (cont’d)
4.5 V < VCC < 5.5 V; (3.0 V < V33V < 5.5V for 3.3 V version); RL = 60 Ω; VINH < VINH,ON;
-40 °C < Tj < 150 °C; all voltages with respect to ground; positive current flowing into pin;
unless otherwise specified.
Parameter
Symbol
Limit Values
Min.
Typ.
Unit Remarks
Max.
Dynamic CAN-Transceiver Characteristics
Propagation delay
TxD-to-RxD LOW
(recessive to
dominant)
td(L),TR
–
150
280
ns
Propagation delay
TxD-to-RxD HIGH
(dominant to
recessive)
td(H),TR
–
150
280
ns
Propagation delay
TxD LOW to bus
dominant
td(L),T
–
100
140
ns
Propagation delay
TxD HIGH to bus
recessive
td(H),T
–
100
140
ns
Propagation delay bus td(L),R
dominant to RxD LOW
–
50
140
ns
Propagation delay bus td(H),R
recessive to RxD
HIGH
–
50
140
ns
CL = 47 pF;
RL = 60 Ω;
VCC = 5 V;
CRxD = 20 pF
CL = 47 pF;
RL = 60 Ω;
VCC = 5 V;
CRxD = 20 pF
CL = 47 pF;
RL = 60 Ω;
VCC = 5 V
CL = 47 pF;
RL = 60 Ω;
VCC = 5 V
CL = 47 pF;
RL = 60 Ω;
VCC = 5 V;
CRxD = 20 pF
CL = 47 pF;
RL = 60 Ω;
VCC = 5 V;
CRxD = 20 pF
1) Vdiff = VCANH - VCANL
2) Deviation from ISO/DIS 11898
Data Sheet
21
Rev. 4.0, 2008-04-28
TLE6250
Diagrams
INH
7
TxD
CANH
RM
47 pF
8
1
5
60 Ω
RxD
6
4
20 pF
CANL
GND
VCC
3
5V
100 nF
2
AEA03328.VSD
Figure 7
Test Circuit for Dynamic Characteristics (5 V Version)
INH
7
TxD
CANH
RxD
8
1
4
20 pF
47 pF
60 Ω
V33 V
6
5
3.3 V
100 nF
CANL
GND
2
VCC
3
5V
100 nF
AEA03329.VSD
Figure 8
Data Sheet
Test Circuit for Dynamic Characteristics (GV33 Version)
22
Rev. 4.0, 2008-04-28
TLE6250
VTxD
VCC(33V)
GND
VDIFF
td(L), T
td(H), T
t
VDIFF(d)
VDIFF(r)
VRxD
td(L), R
t
td(H), R
VCC(33V)
0.7VCC(33V)
0.3VCC(33V)
GND
td(L), TR
td(H), TR
t
AET02926
Figure 9
Data Sheet
Timing Diagrams for Dynamic Characteristics
23
Rev. 4.0, 2008-04-28
TLE6250
Application
120 Ω
T L E6250 G
V Bat
C AN
Bus
RM
IN H
7
6
C AN H
R xD
C AN L
T xD
GN D
V CC
5
8
4
µP
1
3
100
nF
2
100
nF
GN D
e. g . T LE 4270
VI
+
22
µF
100
nF
5V
VQ
+
GN D
22 µF
EC U 1
T L E6250 GV33
IN H
R xD
7
6
T xD
C AN H
V 33
C AN L
GN D
22
µF
100
nF
1
µP
V
V CC
e. g . T LE 4476
+
4
5
2
V Q1
VI
8
3
100
nF
100
nF
3.3 V
22 µF
+
+
22 µF
EC U X
120 Ω
Figure 10
Data Sheet
GN D
5V
V Q2
GN D
100
nF
AEA03308.VSD
Application Circuit TLE6250G with TLE6250GV33
24
Rev. 4.0, 2008-04-28
TLE6250
0.1
2)
0.41+0.1
-0.06
0.2
8
5
1
4
5 -0.2 1)
M
0.19 +0.06
C
B
8 MAX.
1.27
0.35 x 45˚
4 -0.2 1)
1.75 MAX.
0.175 ±0.07
(1.45)
Package Outlines
0.64 ±0.25
6 ±0.2
A B 8x
0.2
M
C 8x
A
Index Marking
1) Does not include plastic or metal protrusion of 0.15 max. per side
2) Lead width can be 0.61 max. in dambar area
GPS01181
Figure 11
PG-DSO-8 (PG-DSO-8-16 Plastic Dual Small Outline)
Green Product (RoHS compliant)
To meet the world-wide customer requirements for environmentally friendly products
and to be compliant with government regulations the device is available as a green
product. Green products are RoHS-Compliant (i.e Pb-free finish on leads and suitable
for Pb-free soldering according to IPC/JEDEC J-STD-020).
You can find all of our packages, sorts of packing and others in our
Infineon Internet Page “Products”: http://www.infineon.com/products.
Dimensions in mm
SMD = Surface Mounted Device
Data Sheet
25
Rev. 4.0, 2008-04-28
TLE6250
Revision History:
2008-04-28
Rev. 4.0
Previous Version:Rev. 3.9 (Data Sheet)
Page
Correction inside the TLE6250GV33 characteristics
Page 20
Changed symbol for the leakage current CANH/L:
From ICANH,lk to ICANH/L,lk
Changed maximum limit for the parameter:
Output current, ICANH/L,lk, VCC = 0 V,VCANH = VCANL = 7 V:
From 300 µA to 400 µA
Page 26
updated Revision History
Template: central_tmplt_a5.fm / 5 / 2003-04-01