TRUMPower 110 WATT MEDICAL POWER ADAPTERS TMP110 SERIES D E SCR IPTION (MDD) The TMP110 series of AC/DC switching power adapters are for 110 watts of continuous output power. They are enclosed in a 94V-1 rated polyphenylene-oxide case with an IEC 320 inlet to mate with interchangeable cord for world-wide use. An on/off switch can be added at request. All models meet CISPR 11 and FCC class B emission limits, and are designed for medical applications. F EATU R E S ‧ ‧ ‧ ‧ ‧ ‧ ‧ ‧ D u a l , t r i p l e o r q u a d r u p l e o u t p u ts Optional output connectors Optional on/off sw itch Optional Power Fail Detect (PFD) signal 100% burn-in W i d e i n p u t r a n g e 8 5 t o 2 6 4 VA C Input surge current protection O v e r v o l ta g e p r o t e c t i o n ‧ Overcurrent protection Saf et y Sta n da rd A ppr o va ls： UL 2601-1 CSA C22.2 No. 601.1 TÜV EN60601-1 IN PUT S PE C IF ICAT ION S E N V IR O N M ENTA L SP E C IF ICATI O N S I n p u t v o l ta g e ： 8 5 t o 2 6 4 VA C Input frequency： 47 to 63 Hz Input current： 3 . 2 0 A ( r m s ) f o r 11 5 VA C 1 . 8 0 A ( r m s ) f o r 2 3 0 VA C L e a k a g e c u r r e n t ： 9 0 µ A m a x . @ 11 5 VA C , 6 0 H z 1 5 0 µ A m a x . @ 2 3 0 VA C , 5 0 H z Operating temperature： Storage temperature： Relative humidity： Derating： OUTPUT SPECIFICATIONS GENERAL SPECIFICATIONS Output voltage/current： See rating chart Switching frequency： 20KHz to 250KHz, varies with load and line Total output power： 110 watts maximum Efficiency： Ripple and noise： 1% peak to peak maximum Overvoltage protection： Provided on output #1 only; set at 112-132% of its nominal output voltage Overcurrent protection： All outputs protected to short circuit conditions Temperature coefficient： All outputs ±0.04%/ºC maximum Transient response： Maximum excursion of 4% or better on all models, recovering to 1% of final value within 500us after a 25% step load change PFD signal (optional): TTL logic high for normal operation and TTL logic low upon loss of input power. This signal appears at least 1ms prior to +5V output dropping 5% below its nominal value. This signal also provides a minimum delay of 100ms after +5V is within regulation. Hold-up time： Line regulation： 0ºC to +70ºC -40ºC to +85ºC 5% to 95% non-condensing Derate from 100% at +50ºC linearly to 50% at +70ºC 70% minimum on single output models with Vo ≥12V, 65% minimum on the others 12 msec minimum at 110VAC ±0.5% maximum at full load Inrush current： 15 amps @ 115VAC, or 30 amps @230VAC, at 25ºC cold start Withstand voltage： 4000VAC from input to output 1500VAC from input to ground 500VAC from output to ground MTBF： 550,000 hours minimum at full load at 25ºC ambient, calculated per MIL-HDBK-217F, excluding DC fan. EMC Performance (EN60601-1-2: 2001) E N 5 5 0 11 : Class B conducted, Class B radiated FCC: Class B conducted, Class B radiated VCCI: Class B conducted, Class B radiated EN61000-3-2: Harmonic distortion, Class A EN61000-3-3: Line flicker EN61000-4-2: ESD, ±8KV air and ±6KV contact EN61000-4-3: Radiated immunity, 3V/m for 80~2500MHz EN61000-4-4: Fast transient/burst, ±2KV EN61000-4-5: Surge, ±1KV diff, ±2KV com. EN61000-4-6: Conducted immunity, 3Vrms EN61000-4-8: Magnetic field immunity, 3A/m E N 6 1 0 0 0 - 4 - 11 : Voltage dips, 30% reduction for 500ms, 60% reduction for 100ms and >95% reduction for 10ms Tumbler Technologies + TRUMPower 3350 Scott Blvd., Bldg. 13, Santa Clara, California 95054, USA Phone: 408-988-6616 ● Fax: 408-988-6622 ● email: [email protected] ● Website: www.TRUMPower.com MEDICAL GRADE TMP110 SERIES OUTPUT VOLTAGE/CURRENT RATING CHART Product No. Output #1 Output #2 (1) Output #3 Vnom. Imin. Imax. Tol. Vnom. Imin. Imax. Ipeak Tol Vnom. Imin. Imax. Tol Output Output #4 Vnom. Imin. Imax. Tol. Power TMP110-D23 +5V 0.8A 10A 5% +12V 0A 5A 9.0A 5% TMP110-T31 +5V 0.8A 10A 5% +12V 0A 5A 9.0A 5% -12V 0A 2A 5% TMP110-T32 +5V 0.8A 10A 5% +15V 0A 4A 7.5A 5% -15V 0A 2A 5% TMP110-Q40 +5V 0.8A 10A 5% +12V 0A 5A 9.0A 5% -12V 0A 2A 5% -5V 0A 2A 5% 110W TMP110-Q41 +5V 0.8A 10A 5% +15V 0A 4A 7.5A 5% -15V 0A 2A 5% +24V 0A 2A 5% 110W TMP110-Q42 +5V 0.8A 10A 5% +12V 0A 5A 9.0A 5% -12V 0A 2A 5% +12V 0A 2A 5% 110W TMP110-Q45 +5V 0.8A 10A 5% +12V 0A 5A 9.0A 5% -12V 0A 2A 5% +24V 0A 2A 5% 110W TMP110-Q45-1 +5V 2.0A 10A 5% +12V 0A 5A 9.0A 5% -12V 0A 2A 5% +24V 1.5A 3A 10% 110W TMP110-Q45-2 +5V 0.8A 10A 5% +24V 0A 3A 5.0A 5% -12V 0A 2A 5% +12V 0A 2A 5% 110W TMP110-Q46 +5V 0.8A 10A 5% +15V 0A 4A 7.5A 5% -15V 0A 2A 5% -5V 0A 2A 5% 110W Notes: (N/A) (N/A) 110W (N/A) 110W (N/A) 110W (1) Peak output current with 10% maximum duty cycle for less than 60 seconds. Total peak power must not exceed 130 watts. (2) The output #1 of model TMP110-Q45-1 needs a minimum current of 2A to support the other outputs at their maximum rated loads. MECHANICAL SPECIFICATIONS NOTES: 1. Dimensions shown in inch [mm] 2. Tolerance 0.02 [0.5] maximum 3. Weight: 1.40 Kgs (3.08 Lbs.) approx. 4. Standard output connector is an 8-pin at 270º male DIN plug. For other output connector options, please consult factory. 5. To order a model with on/off switch, add suffix “S” to the product number. e.g. TMP110-T31-S. 6. To order a model with PFD signal, add suffix “PF” to the product number, e.g. TMP110-T31-PF. PIN CHART PIN Product No. TMP110-D23 TMP110-T31 TMP110-Q40 TMP110-Q42 TMP110-Q45-1 TMP110-Q46 TMP110-T32 TMP110-Q41 TMP110-Q45 TMP110-Q45-2 1 2 3 4 5 6 7 8 COMMON RETURN N.C. OUTPUT #1. N.C. OUTPUT #2. COMMON RETURN OUTPUT #1 N.C. or PFD COMMON RETURN OUTPUT #3 OUTPUT #1. N.C OUTPUT #2. COMMON RETURN OUTPUT #1 N.C. or PFD COMMON RETURN OUTPUT #3 OUTPUT #1. OUTPUT #4 OUTPUT #2.. COMMON RETURN OUTPUT #1 N.C. or PFD. Tumbler Technologies + TRUMPower 3350 Scott Blvd., Bldg. 13, Santa Clara, California 95054, USA Phone: 408-988-6616 ● Fax: 408-988-6622 ● email: [email protected] ● Website: www.TRUMPower.com