TP30-xxx Series ® TRISILTM FEATURES n n n n n BIDIRECTIONAL CROWBAR PROTECTION. VOLTAGE RANGE: FROM 62 V TO 270 V. HOLDING CURRENT : IH = 150 mA min. REPETITIVE PEAK PULSE CURRENT : IPP = 30 A, 10/1000 µs. JEDEC REGISTERED PACKAGE OUTLINE DO-15 DESCRIPTION The TP30-xxx series has been designed to protect telecommunication equipment against lightning surges and overvoltages induced by AC power lines. SCHEMATIC DIAGRAM Peak Surge Voltage (V) Voltage Waveform (µs) Current Waveform (µs) Admissible Ipp (A) Necessary Resistor (Ω) (CCITT) ITU-K20 1000 10/700 5/310 25 - (CCITT) ITU-K17 1500 10/700 5/310 38 - VDE0433 2000 10/700 5/310 40 10 VDE0878 2000 1.2/50 1/20 50 - level 2 level 3 10/700 1.2/50 5/310 8/20 25 50 - FCC Part 68, lightning surge type A 1500 800 10/160 10/560 10/160 10/560 65 50 15.5 8.0 FCC Part 68, lightning surge type B 1000 9/720 5/320 25 - BELLCORE TR-NWT-001089 First level 2500 1000 2/10 10/1000 2/10 10/1000 125 30 15.0 23.3 BELLCORE TR-NWT-001089 Second level 5000 2/10 2/10 125 15.0 CNET l31-24 1000 0.5/700 0.8/310 25 - COMPLIES WITH THE FOLLOWING STANDARDS: IEC-1000-4-5 February 2003 - Ed: 6B 1/6 TP30-xxx Series ABSOLUTE MAXIMUM RATINGS (Tamb = 25°C) Symbol P Parameter Power dissipation on infinite heatsink Value Unit Tamb = 50 °C 3 W IPP Peak pulse current 10/1000 µs 8/20 µs 30 60 A ITSM Non repetitive surge peak on-state current tp = 20 ms 15 A tp = 20 ms 1 A2s 2 I t dV/dt 2 I t value for fusing Critical rate of rise of off-state voltage VRM Tstg Tj Storage temperature range Maximum junction temperature TL Maximum lead temperature for soldering during 10s at 5mm for case 5 kV/µs - 55 to + 150 150 °C °C 230 °C THERMAL RESISTANCES Symbol Rth (j-l) Rth (j-a) Parameter Junction to leads Junction to ambient on printed circuit with standard footprint dimension ELECTRICAL CHARACTERISTICS (Tamb = 25°C) Symbol 2/6 Parameter VRM Stand-off voltage IRM Leakage current at stand-off voltage VR Continuous Reverse voltage VBR Breakdown voltage VBO Breakover voltage IH Holding current IBO Breakover current IPP Peak pulse current C Capacitance Value Unit 60 °C/W 100 °C/W TP30-xxx Series Type TP30-62 TP30-68 TP30-100 TP30-120 TP30-130 TP30-180 TP30-200 TP30-220 TP30-240 TP30-270 Note 1: Note 2: Note 3: Note 4: Note 5: IRM @ VRM max IR @ VR VBO @ IBO max note 2 max note 1 IH min note 3 µA V A V V mA mA 2 2 2 2 2 2 2 2 2 2 56 61 90 108 117 162 180 198 216 243 50 50 50 50 50 50 50 50 50 50 62 68 100 120 130 180 200 220 240 270 82 90 133 160 173 240 267 293 320 360 800 800 800 800 800 800 800 800 800 800 150 150 150 150 150 150 150 150 150 150 C typ note 4 typ note 5 pF 50 50 40 40 35 35 30 30 30 30 20 20 16 16 14 14 12 12 12 12 IR measured at VR guarantee VBRmin VR Measured at 50 Hz (1 cycle) - See test circuit 1. See test circuit 2. VR = 1V, F = 1MHz. VR = 50V, F = 1MHz. TEST CIRCUIT 1 FOR IBO and VBO parameters : tp = 20ms Auto Transformer 220V/2A R1 static relay. 140 R2 240 K 220V Vout IBO measure D.U.T V BO measure Transformer 220V/800V 5A TEST PROCEDURE : n Pulse Test duration (tp = 20ms): - For Bidirectional devices = Switch K is closed - For Unidirectional devices = Switch K is open. n VOUT Selection - Device with VBO < 250 Volt - VOUT = 250 VRMS, R1 = 140 Ω. - Device with VBO 250 Volt - VOUT = 480 VRMS, R2 = 240 Ω. 3/6 TP30-xxx Series TEST CIRCUIT 2 for IH parameter. R D.U.T. - VP VBAT = - 48 V Surge generator This is a GO-NOGO Test which allows to confirm the holding current (IH) level in a functional test circuit. TEST PROCEDURE : n 1) Adjust the current level at the IH value by short circuiting the AK of the D.U.T. 2) Fire the D.U.T with a surge Current : Ipp = 10A , 10/1000 µs. 3) The D.U.T will come back off-state within 50 ms max. 4/6 TP30-xxx Series Fig. 1: Non repetitive surge peak on-sate current versus overload duration (Tj initial = 25°C). ITSM(A) 20 F = 50Hz 15 10 5 0 1E-2 1E-1 1E+0 1E+1 1E+2 1E+3 Fig. 2: Relative variation of holding current versus junction temperature. IH[Tj] / IH[Tj=25°C] 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 -40 -20 0 20 t(s) Fig. 3: Relative variation of junction capacitance versus reverse applied voltage (typical values). 40 Tj(°C) 60 80 100 120 Fig. 4: On-state voltage versus on-state current (typical values). IT(A) C[VR]/C[VR=1V] 50 1.0 Tj = 25°C F = 1MHz 20 0.5 10 5 0.2 2 0.1 1 10 100 300 1 0 1 2 3 4 VR(V) Fig. 5: Variation of thermal impedance junction to ambient versus pulse duration. 5 VT(V) 6 7 8 9 10 Fig. 6: Relative variation of VBO voltage versus junction temperature. Vbo[Tj]/Vbo[Tj=25°C] Zth(j-a)(°CW) 1.10 1E+2 1.05 1E+1 1.00 270 V 1E+0 0.95 1E-1 1E-3 1E-2 1E-1 1E+0 tp(s) 1E+1 1E+2 5E+2 62 V 0.90 -40 -20 0 20 40 Tj(°C) 60 80 100 5/6 TP30-xxx Series ORDER CODE TP 30 - 62 TRISIL PROTECTION VOLTAGE IPP = 30 A MARKING : Logo, Date Code, Part Number. PACKAGE MECHANICAL DATA DO-15 (Plastic) REF. C D Millimeters C A DIMENSIONS Inches Min. Max. Min. Max. A 6.05 6.75 0.238 0.266 B 2.95 3.53 0.116 0.139 C 26 31 1.024 1.220 D 0.71 0.88 0.028 0.035 B Packaging : Tape and reel. Weight : 0.4 g. Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics © 2003 STMicroelectronics - Printed in Italy - All rights reserved. STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - Finland - France - Germany Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco - Singapore Spain - Sweden - Switzerland - United Kingdom - United States. http://www.st.com 6/6