TPS72101, TPS72115 TPS72116, TPS72118 Actual Size (3,00 mm x 3,00 mm) www.ti.com SLVS352B – DECEMBER 2001 – REVISED MAY 2002 LOW INPUT VOLTAGE, CAP FREE 150-mA LOW-DROPOUT LINEAR REGULATORS FEATURES D 150-mA LDO D Available in 1.5-V, 1.6-V, 1.8-V Fixed-Output and Adjustable Versions D Low Input Voltage Requirement (Down to 1.8 V) D Small Output Capacitor, 0.1-µF D Dropout Voltage Typically 200 mV at 150 mA D Less Than 1 µA Quiescent Current in Shutdown Mode D Thermal Protection D Over Current Limitation D 5-Pin SOT-23 (DBV) Package APPLICATIONS D D D D D D D D D Portable Communication Devices Battery Powered Equipment PCMCIA Cards Personal Digital Assistants Modems voltage (150 mV at full load). Therefore, compared to many other regulators that require 2.5-V or higher input voltages for operation, these regulators can be operated directly from two AAA batteries. Also, the typical quiescent current (ground pin current) is low, starting at 85 µA during normal operation and 1 µA in shutdown mode. These regulators can be operated very efficiently and, in a battery-powered application, help extend the longevity of the device. Similar LDO regulators require 1-µF or larger output capacitors for stability. However, this regulator uses an internal compensation scheme that stabilizes the feedback loop over the full range of input voltages and load currents with output capacitances as low as 0.1-µF. Ceramic capacitors of this size are relatively inexpensive and available in small footprints. This family of regulators is particularly suited as a portable power supply solution due to its minimal board space requirement and 1.8-V minimum input voltage. Being able to use two off-the-shelf, AAA, batteries makes system design easier and also reduces component cost. Moreover, the solution will be more efficient than if a regulator with a higher input voltage is used. Bar Code Scanners DBV PACKAGE (TOP VIEW) Backup Power Supplies SMPS Post Regulation IN 1 GND 2 EN 3 5 OUT 4 NC/FB Internet Audio DESCRIPTION The TPS721xx family of LDO regulators is available in fixed voltage options that are commonly used to power the latest DSP’s and microcontrollers with an adjustable option ranging from 1.22 V to 2.5 V. These regulators can be used in a wide variety of applications ranging from portable, battery-powered equipment to PC peripherals. The family features operation over a wide range of input voltages (1.8 V to 5.5 V) and low dropout 1.8 V TPS72115 IN EN 0.1 µF 1.5 V OUT GND 0.1 µF Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright 2002, Texas Instruments Incorporated TPS72101, TPS72115 TPS72116, TPS72118 www.ti.com SLVS352B – DECEMBER 2001 – REVISED MAY 2002 These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. ORDERING INFORMATION TJ VOLTAGE PACKAGE Adjustable 1.5 V –40°C 40°C to 125°C SOT 23 SOT-23 (DBV) 1.6 V 1.8 V (1) The DBVT indicates tape and reel of 250 parts. (2) The DBVR indicates tape and reel of 3000 parts. PART NUMBER TPS72101DBVT(1) TPS72101DBVR(2) (1) TPS72115DBVT TPS72115DBVR(2) TPS72116DBVT(1) TPS72118DBVT(1) SYMBOL PEKI PEII TPS72116DBVR(2) TPS72118DBVR(2) PHFI PEJI ABSOLUTE MAXIMUM RATINGS over operating free-air temperature range unless otherwise noted(1) TPS72101, TPS72115 TPS72116, TPS72118 Input voltage range(2) – 0.3 V to 7 V Voltage range at EN –0.3 V to 7 V Voltage on OUT, FB, NC –0.3 V to VI + 0.3 V Peak output current Internally limited ESD rating, HBM 3 kV Continuous total power dissipation See Dissipation Rating Table Operating virtual junction temperature range, TJ – 40°C to 150°C Storage temperature range, Tstg – 65°C to 150°C (1) Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. (2) All voltage values are with respect to network ground terminal. PACKAGE DISSIPATION RATING BOARD PACKAGE RθJC RθJA DERATING FACTOR ABOVE TA = 25°C TA ≤ 25°C POWER RATING TA = 70°C POWER RATING TA = 85°C POWER RATING Low K(1) High K(2) DBV 65.8 °C/W 259 °C/W 3.9 mW/°C 386 mW 212 mW 154 mW DBV 65.8 °C/W 180 °C/W 5.6 mW/°C 555 mW 305 mW 222 mW (1) The JEDEC Low K (1s) board design used to derive this data was a 3 inch x 3 inch, two-layer board with 2 ounce copper traces on top of the board. (2) The JEDEC High K (2s2p) board design used to derive this data was a 3 inch x 3 inch, multilayer board with 1 ounce internal power and ground planes and 2 ounce copper traces on top and bottom of the board. 2 TPS72101, TPS72115 TPS72116, TPS72118 www.ti.com SLVS352B – DECEMBER 2001 – REVISED MAY 2002 ELECTRICAL CHARACTERISTICS over recommended operating free-air temperature range VI = VO(typ) + 1 V, IO= 1 mA, EN = VI, Co = 1 µF (unless otherwise noted) PARAMETER TEST CONDITIONS VI IO Input voltage(1) TJ Operating junction temperature VO MIN Output Out ut voltage 0 µA< IO < 150 mA,(1) 1.8 V ≤ VO ≤ 2.5 V TPS72115 TJ = 25°C 0 µA< IO < 150 mA, 2.5 V ≤ VI ≤ 5.5 V TPS72116 TJ = 25°C 0 µA< IO < 150 mA, TPS72118 TJ = 25°C 0 µA< IO < 150 mA, MAX V 0 150 mA –40 125 °C 0.97 VO 1.03 VO 1.5 1.455 1.545 1.6 2.6 V ≤ VI ≤ 5.5 V 1.552 V 1.648 1.8 2.8 V ≤ VI ≤ 5.5 V 1.746 TJ = 25°C 1.854 85 120 I(Q) Quiescent current (GND current) Standby current Vn Output noise voltage Vref Reference voltage PSRR IO = 150 mA, IO = 150 mA TJ = 25°C 570 EN < 0.5 V, TJ = 25°C 0.01 Ripple rejection Current limit Co = 1 µF f = 100 Hz, Co = 10 µF, IO = 150 mA, See Note 2 TJ = 25°C, See Note 1 55V VO + 1 V < VI ≤ 5.5 Output voltage load regulation 0 < IO < 150 mA, TPS72118 1 BW = 200 Hz to 100 kHz, TJ = 25°C, TJ = 25°C Out ut voltage line regulation Output (∆VO/VO)(3) V 48 dB 525 0.03 TJ = 25°C 0.5 1.4 EN low level input –0.2 II EN iinputt currentt VDO (4) D Dropout t voltage lt In Feedback input current –0.01 EN = IN –0.01 IO = 150 mA, IO = 150 mA, TJ = 25°C 1.2 V ≤ VO ≤ 5.2 V %/V mV 0.4 EN = 0 V mA 0.09 0.1 EN high level input TPS72101 1.225 175 TJ = 25°C µA A µV 90 VIH VIL TPS72118 µA A 850 EN < 0.5 V TPS72115 UNIT 5.5 Continuous output current TPS72101 TYP 1.8 V µA A 150 240 TPS72101 1 mV V µA 1 Thermal shutdown temperature Thermal shutdown hysteresis (1) Minimum IN operating voltage is 1.8 V or VO(max) + VDO (max load), whichever is greater. (2) Test condition includes, output voltage VO=1 V and pulse duration = 10 mS. (3) VImin = (VO + 1) or 1.8 V whichever is greater. Line regulation (mV) + ǒ%ńVǓ V ǒ5.5 V * V IminǓ O 100 170 °C 20 °C 1000 (4) Dropout voltage is defined as the differential voltage between VO and VI when VO drops 100 mV below the value measured with VI = VO + 1 V. 3 TPS72101, TPS72115 TPS72116, TPS72118 www.ti.com SLVS352B – DECEMBER 2001 – REVISED MAY 2002 FUNCTIONAL BLOCK DIAGRAM—ADJUSTABLE VERSION TPS72101 OUT IN EN Current Limit / Thermal Protection Vref FB GND FUNCTIONAL BLOCK DIAGRAM—FIXED VERSION TPS72115/16/18 OUT IN EN Current Limit / Thermal Protection Vref GND NC (see Note 1) (1) This pin must be left floating and not connected to GND. Terminal Functions TERMINAL NAME NO. I/O DESCRIPTION GND 2 EN 3 I Enable input IN 1 I Input supply voltage NC/FB 4 I NC = Not connected (see Note 6); FB = Feedback (adjustable option TPS72101) OUT 5 O Regulated output voltage 4 Ground TPS72101, TPS72115 TPS72116, TPS72118 www.ti.com SLVS352B – DECEMBER 2001 – REVISED MAY 2002 TYPICAL CHARACTERISTICS TPS72118 TPS72118 TPS72118 OUTPUT VOLTAGE vs OUTPUT CURRENT OUTPUT VOLTAGE vs JUNCTION TEMPERATURE GROUND CURRENT vs JUNCTION TEMPERATURE 1.8040 VI = 2.8 V Co = 1 µF TJ = 25° C 1.8020 V O – Output Voltage – V 1.8000 1.7999 1.7998 1.7997 1.7996 30 60 90 120 IO – Output Current – mA 1.8000 IO = 1 mA 1.7980 IO = 150 mA 1.7960 200 1.7920 100 IO = 1 mA Figure 2 OUTPUT IMPEDANCE vs FREQUENCY 400 300 TJ = 25° C 200 TJ = –40° C 60 90 1k VI = 2.8 V Co = 1 µF µ V/ TJ = 125° C 500 30 2.5 120 1.5 IO = 150 mA 1 10 IO = 1 mA 1 0.1 IO = 150 mA 0.5 0.01 IO = 1 mA 0 100 150 VI = 2.8 V Co = 1 µF 100 2 Output Impedance – Ω Hz TPS72118 OUTPUT SPECTRAL NOISE DENSITY vs FREQUENCY Output Spectral Noise Density – Ground Current – µ A Figure 3 GROUND CURRENT vs OUTPUT CURRENT 100 1k IO – Output Current – mA 10 k 0.001 100 k 1 f – Frequency – Hz 10 100 1 k 10 k 100 k 1 M f – Frequency – Hz Figure 5 Figure 4 10 M Figure 6 TPS72118 TPS72118 TPS72118 DROPOUT VOLTAGE vs JUNCTION TEMPERATURE POWER SUPPLY RIPPLE REJECTION vs FREQUENCY OUTPUT VOLTAGE, ENABLE VOLTAGE vs TIME (START-UP) 70 VI = 2.8 V Co = 1 µF 200 IO = 150 mA 150 100 50 IO = 10 mA 0 –40 –25 –10 5 20 35 50 65 80 95 110 125 TJ – Junction Temperature – °C Figure 7 Power Supply Ripple Rejection – dB 250 V DO – Dropout Voltage – mV 20 35 50 65 80 95 110 125 TJ – Junction Temperature – °C TPS72118 VI = 2.8 V Co = 1 µF 0 0 –40 –25 –10 5 TPS72118 700 0 300 1.7940 Figure 1 600 IO = 150 mA 400 1.7900 –40 –25 –10 5 20 35 50 65 80 95 110 125 TJ – Junction Temperature – °C 150 VI = 2.8 V Co = 1 µF 500 VI = 2.8 V Co = 1 µF IO = 150 mA 60 50 40 Enable Voltage – V 1.7995 0 600 VEN 3 2 1 0 30 20 10 0 1 10 100 1k 10 k f – Frequency – Hz Figure 8 100 k 1 M V – Output Voltage – V O V O – Output Voltage – V 1.8001 700 VI = 2.8 V Co = 1 µF Ground Current – µ A 1.8002 2 1 VO 0 0 VI = 2.8 V VO = 1.8 V IO = 150 mA Co = 1 µF 50 100 150 200 200 300 350 400 450 500 t – Time – µs Figure 9 5 TPS72101, TPS72115 TPS72116, TPS72118 www.ti.com SLVS352B – DECEMBER 2001 – REVISED MAY 2002 TPS72118 LOAD TRANSIENT RESPONSE IO = 150 mA Co = 1 µF VI 3.8 2.8 dV I 1 dt VO + 0.4 V µs POWER UP / POWER DOWN 6 VI = 2.8 V Co = 1 µF 100 5 Power Up / Power Down – V ∆ V O – Change In Output Voltage – mV TPS72118 LINE TRANSIENT RESPONSE 0 –100 dI I O – Output Current – mA V O – Output Voltage –V V I – Input Voltage – V TYPICAL CHARACTERISTICS O 0.1A + µs dt 150 0 100 -1 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 t – Time – ms VI 4 3 2 VO 1 Co = 1 µF Ci = 1 µF RL = 12 Ω 0 50 0 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 0 1 10 20 30 40 90 100 Figure 12 Figure 11 Figure 10 50 60 70 80 t – Time – ms t – Time – ms TPS72101 DC DROPOUT VOLTAGE vs OUTPUT CURRENT DROPOUT VOLTAGE vs INPUT VOLTAGE 250 MINIMUM REQUIRED INPUT VOLTAGE vs OUTPUT VOLTAGE 250 TJ = 125°C 150 TJ = 25°C 100 TJ = –40°C 50 0 0 15 30 45 60 75 90 105 120 135 150 IO – Output Current – mA Figure 13 6 V DO – Dropout Voltage – mV DC Dropout Voltage – mV 200 200 TJ = 125°C 150 TJ = 25°C 100 TJ = –40°C 50 0 1.8 2.5 3.3 4 VI – Input Voltage – V Figure 14 4.8 5.5 V I – Minimum Required Input Voltage – V 5.5 IO = 150 mA IO = 150 mA 5 TJ = 125°C 4.5 TJ = 25°C 4 3.5 3 TJ = –40°C 2.5 2 1.5 1 1 1.5 2 2.5 3 3.5 4 4.5 VO – Output Voltage – V Figure 15 5 5.5 TPS72101, TPS72115 TPS72116, TPS72118 www.ti.com SLVS352B – DECEMBER 2001 – REVISED MAY 2002 APPLICATION INFORMATION The TPS721xx family of low-dropout (LDO) regulators functions with a very low input voltage (>1.8 V). The dropout voltage is typically 150 mV at full load. Typical quiescent current (ground pin current) is only 85 µA and drops to 1 µA in the shutdown mode. DEVICE OPERATION The TPS721xx family can be operated at low input voltages due to low voltage circuit design techniques and a PMOS pass element that exhibits low dropout. A logic low on the enable input, EN, shuts off the output and reduces the supply current to less than 1 µA. EN may be tied to VIN in applications where the shutdown feature is not used. Current limiting and thermal protection prevent damage by excessive output current and/or power dissipation. The device switches into a constant-current mode at approximately 350 mA; further load reduces the output voltage instead of increasing the output current. The thermal protection shuts the regulator off if the junction temperature rises above 170°C. Recovery is automatic when the junction temperature drops approximately 20°C below the high temperature trip point. The PMOS pass element includes a back diode that safely conducts reverse current when the input voltage level drops below the output voltage level. A typical application circuit is shown in Figure 16. TPS721xx VI 1 IN OUT 5 VO 0.1 µF NC 3 4 EN + GND 0.1 µF 2 Figure 16. Typical Application Circuit DUAL SUPPLY APPLICATION In portable, battery-powered electronics, separate power rails for the DSP or microcontroller core voltage (VCORE) and I/O peripherals (VIO) are usually necessary. The TPS721xx family of LDO linear regulators is ideal for providing V(CORE) for the DSP or microcontroller. As shown in Figure 17, two AAA batteries provide an input voltage to a boost converter and the TPS72115 LDO linear regulator. The batteries combine input voltage ranges from 3.0 V down to 1.8 V near the end of their useful lives. Therefore, a boost converter is necessary to provide the typical 3.3 V needed for VIO, and the TPS72115 linear regulator provides a regulated V(CORE) voltage, which in this example is 1.5 V. Although there is no explicit circuitry to perform power-up sequencing of first V(CORE) then VIO, the output of the linear regulator reaches its regulated voltage much faster (<400 µs) than the output of any switching type boost converter due to the inherent slow start up of those types of converters. Assuming a boost converter with minimum VI of 1.8 V is appropriately chosen, this power supply solution can be used over the entire life of the two off-the-shelf AAA batteries. Thus, this solution is very efficient and the design time and overall cost of the solution is minimized. 7 TPS72101, TPS72115 TPS72116, TPS72118 www.ti.com SLVS352B – DECEMBER 2001 – REVISED MAY 2002 1.8 V – 3 V 3.3 V VIO Boost Converter DSP or Controller 1.8 V 1.5 V TPS72115 VCORE Two AAA Batteries Figure 17. Dual Supply Application Circuit EXTERNAL CAPACITOR REQUIREMENTS A 0.1-µF ceramic bypass capacitor is required on both the input and output for stability. Larger capacitors improve transient response, noise rejection, and ripple rejection. A higher value electrolytic input capacitor may be necessary if large, fast rise time load transient are anticipated, and/or there is significant input resistance from the device to the input power supply. POWER DISSIPATION AND JUNCTION TEMPERATURE Specified regulator operation is assured to a junction temperature of 125°C; the maximum junction temperature allowable without damaging the device is 150°C. This restriction limits the power dissipation the regulator can handle in any given application. To ensure the junction temperature is within acceptable limits, calculate the maximum allowable dissipation, PD(max), and the actual dissipation, PD, which must be less than or equal to PD(max). The maximum-power-dissipation limit is determined using the following equation: P T max * T A + J D(max) R qJA Where: TJmax is the maximum allowable junction temperature. RθJA is the thermal resistance junction-to-ambient for the package, see the power dissipation rating table. TA is the ambient temperature. The regulator dissipation is calculated using: P D ǒ + V *V I O Ǔ I O Power dissipation resulting from quiescent current is negligible. 8 TPS72101, TPS72115 TPS72116, TPS72118 www.ti.com SLVS352B – DECEMBER 2001 – REVISED MAY 2002 PROGRAMMING THE TPS72101 ADJUSTABLE LDO REGULATOR The output voltage of the TPS72101 adjustable regulator is programmed using an external resistor divider as shown in Figure 18. The output voltage is calculated using: V O +V ǒ1 ) R1 Ǔ R2 ref (1) Where: Vref = 1.225 V typ (the internal reference voltage) Resistors R1 and R2 should be chosen for approximately 10-µA divider current. Lower value resistors can be used but offer no inherent advantage and waste more power. Higher values should be avoided, as leakage currents at FB increase the output voltage error. The recommended design procedure is to choose R2 = 121 kΩ to set the divider current at 10 µA and then calculate R1 using: R1 + ǒ Ǔ V V O *1 ref R2 (2) Where: Vref = 1.225 V TPS72101 OUTPUT VOLTAGE PROGRAMMING GUIDE OUTPUT VOLTAGE (V) DIVIDER RESISTANCE (kΩ)† R1 R2 2.5 127 121 3.3 205 121 † 1% values shown. 1 VI IN 0.1 µF OUT ≥ 1.7 V 3 5 VO R1 EN ≤ 0.9 V FB GND 2 4 R2 0.1 µF Figure 18. TPS72101 Adjustable LDO Regulator Programming REGULATOR PROTECTION The TPS721xx pass element has a built-in back diode that safely conducts reverse current when the input voltage drops below the output voltage (e.g., during power down). Current is conducted from the output to the input and is not internally limited. If extended reverse voltage is anticipated, external limiting might be appropriate. The TPS721xx also features internal current limiting and thermal protection. During normal operation, the TPS721xx limits output current to approximately 350 mA. When current limiting engages, the output voltage scales back linearly until the overcurrent condition ends. While current limiting is designed to prevent gross device failure, care should be taken not to exceed the power dissipation ratings of the package. If the temperature of the device exceeds 170°C, thermal-protection circuitry shuts it down. Once the device has cooled down to below 150°C, regulator operation resumes. 9 TPS72101, TPS72115 TPS72116, TPS72118 www.ti.com SLVS352B – DECEMBER 2001 – REVISED MAY 2002 MECHANICAL DATA DBV (R-PDSO-G5) PLASTIC SMALL-OUTLINE 0,50 0,30 0,95 5 0,20 M 4 1,70 1,50 1 0,15 NOM 3,00 2,60 3 Gage Plane 3,00 2,80 0,25 0°–8° 0,55 0,35 Seating Plane 1,45 0,95 0,05 MIN 0,10 4073253-4/F 10/00 NOTES:A. B. C. D. 10 All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion. Falls within JEDEC MO-178 PACKAGE OPTION ADDENDUM www.ti.com 8-Aug-2005 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty TPS72101DBVR ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS72101DBVRG4 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS72101DBVT ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS72101DBVTG4 ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS72115DBVR ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS72115DBVRG4 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS72115DBVT ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS72115DBVTG4 ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS72116DBVR ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS72116DBVRG4 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS72116DBVT ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS72116DBVTG4 ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS72118DBVR ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS72118DBVRG4 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS72118DBVT ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS72118DBVTG4 ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS) or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 8-Aug-2005 Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2005, Texas Instruments Incorporated