ALUMINUM ELECTROLYTIC CAPACITORS WJ 5.5mmL Chip Type High Temperature (260°C) Reflow series Corresponding with 260°C peak reflow soldering Recomended reflow condition : 260°C peak 5 sec. 230°C over 60 sec. 2 times WJ Chip type with 5.5mm height. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine using carrier tape. Load life of 2000 hours at 85°C Adapted to the RoHS directive (2002/95/EC). High Temperature Reflow WX Specifications Item Performance Characteristics Category Temperature Range – 40 ~ +85°C Rated Voltage Range 6.3 ~ 50V Rated Capacitance Range 0.1 ~ 150µF Capacitance Tolerance ± 20% at 120Hz, 20°C Leakage Current After 2 minutes' application of rated voltage, leakage current is not more than 0.01CV or 3 (µA) ,whichever is greater. Measurement frequency : 120Hz, Temperature : 20°C tan δ Rated voltage (V) tan δ (MAX.) 6.3 0.26 10 0.20 After 2000 hours' application of rated voltage at 85°C, capacitors meet the characteristic requirements listed at right. Endurance 35 0.12 16 2 4 10 3 8 6.3 4 8 Rated voltage (V) Z– 25°C / Z+20°C Impedance ratio ZT / Z20 (MAX.) Z– 40°C / Z+20°C Stability at Low Temperature 25 0.14 16 0.16 50 0.12 Measurement frequency : 120Hz 50 35 25 2 2 2 3 3 4 Capacitance change tan δ Leakage Current Within ±20% of initial value 200% or less of initial specified value Initial specifed value or less Shelf Life After storing the capacitors under no load at 85°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above. Resistance to soldering heat The capacitors shall be kept on the hot plate maintained at 250°C for 30 seconds. After removing from the hot plate and restored at room temperature, they meet the characteristic requirements listed at right. Marking Black print on the case top. Chip Type 1 Capacitance 4 5 6 7 8 9 10 11 12 13 14 Configuration A±0.2 A±0.2 +0.1 –0.2 3 Package code E B±0.2 φD±0.5 N2 100A WJ C±0.2 2 UW J 1 C 1 0 0 MC L 1 G B 0.5 MAX. Plastic platform 0.3 MAX. Series 5.4 Lot No. Within ±10% of initial value Initial specified value or less Initial specified value or less Type numbering system (Example : 16V 10µF) Positive Voltage (A:10V) Capacitance change tan δ Leakage current Capacitance toleranc (±20%) Rated Capacitance (10µF) Rated voltage (16V) Series name Negative 0.5 ~ 0.8 Type Voltage (mm) V 6.3 10 16 25 35 50 Code j A C E V H φD A B C E 4 1.8 4.3 4.3 1.0 5 2.1 5.3 5.3 1.3 6.3 2.4 6.6 6.6 2.2 Dimension table in next page. CAT.8100V ALUMINUM ELECTROLYTIC CAPACITORS WJ series Dimensions Cap. (µF) V 6.3 10 16 25 35 50 Code 0J 1A 1C 1E 1V 1H 0.1 0R1 4 1.0 0.22 R22 4 2.0 0.33 R33 4 2.8 0.47 R47 4 4.0 1 010 4 8.4 2.2 2R2 4 13 3.3 3R3 4 17 4.7 4R7 4 16 4 18 5 20 6.3 33 4 23 5 27 5 29 33 5 37 6.3 42 6.3 45 5 41 6.3 49 6.3 52 6.3 52 6.3 58 6.3 76 6.3 86 10 100 22 220 4 28 5 33 330 5 37 47 470 5 45 100 101 6.3 70 150 151 6.3 71 Case size φ D (mm) Rated ripple Rated Ripple (mArms) at 85°C 120Hz Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz~ 1.50 Taping specifications are given in page 24. Recommended land size, soldering by reflow are given in page 25, 26. Please refer to page 3 for the minimum order quantity. CAT.8100V