Medallion 6000 Series 1550 nm Externally-Modulated Transmitter DATASHEET | OCTOBER 2013 FIBER OPTICS The L-Type/D-Type/S-Type/F-Type/N-Type Medallion 6000 Series Applications High-Performance Supertrunking Links High Power Distribution Networks Redundant Ring Architectures FTTx Networks RFoG Applications SAT-IF Transport The Medallion 6000 series is a family of state-of-the-art high-performance 1550 nm externally-modulated CATV fiber optic transmitters optimized for varying network applications. Packaged in convenient 1 RU housing, this line of optical transmitters couples high optical output powers, up to 11.0 dBm, with low optical linewidth resulting in unmatched performance. The optical modulator, combined with proprietary pre-distortion circuitry, provides superior CTB and CSO performance with SBS suppression levels of greater than 21 dBm. Advanced features such as built-in field adjustable SBS control and electronic dispersion compensation allow these transmitters to be quickly optimized in the field for any link or application without the need to procure specifically tuned transmitters. This affords the system designer a level of flexibility previously unknown in the CATV market place. The L-Type series are designed as a high-performance solution for applications where the simultaneous transport of CATV and SAT-IF FM signals is required. The SAT-IF signals can be applied anywhere in the 950 to 2800 MHz band. DWDM Node Splitting Features Single or Dual Optical Outputs QAM Loading to 1003 MHz Dual Power Supplies, Redundant & Hot Swappable The D-Type series are designed as a low cost, high-performance solution for applications where the required fiber length is in the range of 20 to 50 kilometers. Advanced, high power, DFB laser technology allows these transmitters to be fielded without the use of EDFAs. The S-Type series transmitters are designed to be the most versatile models within the Medallion 6000 series family. They can easily be configured to meet most HFC network solutions requiring link lengths in the range of 50 to 70 kilometers with one EDFA as well as links utilizing multiple EDFA’s. Front Panel RF Test Point SNMP Control Interface WEB GUI Vacuum Fluorescent Status Display OMI / RF Gain Adjustment AGC Select: CW, Video, Manual (No AGC) Industry Leading Field Adjustable SBS Suppression Field Adjustable Electronic The F-Type series transmitters are intended for use in FTTx and RFoG architecture designs requiring high-quality transmission over varying transmission lengths and EDFA output powers. These transmitters successfully support very high optical launch powers while controlling the detrimental effects of Stimulated Brillouin Scattering (SBS), group velocity dispersion (GVD), and self phase modulation (SPM). The N-Type series transmitters are intended for use in node-splitting architecture designs requiring cost effective DWDM transmission over medium length fiber distances. Dispersion Compensation (EDC) | REV 2013.10 Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice. Medallion 6000 Series 1550 nm Externally-Modulated Transmitter FIBER OPTICS DATASHEET | OCTOBER 2013 Optical / Electrical Characteristics L-Type Property Performance (Note 1-8) Specified Link Length Units 6000-L01 L (km) Channel Plan Optical Output Power Po (dBm) Models 6000-L02 6000-L03 Comments 6000-L04 25 25 25 25 NTSC 80-Ch PAL 60-Ch NTSC 110-ch PAL 89-Ch 8.5/8.5 8.5/8.5 8.5/8.5 8.5/8.5 With 36 QPSK carriers from 950 to 2800 MHz Min. 10 dBm version avail. See Chart Noise Bandwidth BW (MHz) 4 5 4 5 SBS Suppression (dBm) 15.0 15.0 15.0 15.0 Min. CATV Carrier to Noise Ratio CNR (dB) 51.0 51.0 49.5 49.5 Min. CATV Composite Second Order CSO (dBc) -65 -65 -65 -65 Max. Port 1 CATV Composite Triple Beat CTB (dBc) -65 -65 -65 -65 Max. @ +25°C CATV Composite Triple Beat CTB (dBc) -64 -64 -64 -64 Max. @ 0 C to 50 C SAT-IF Carrier to Noise Ratio CNR (dB) 27 27 27 27 Min. SAT-IF Intermodulation Products (dBc) -35 -35 -35 -35 Max. Port 1 SAT-IF Spurious Products (dBc) -38 -38 -38 -38 Max. o o D-Type Property Performance (Note 1-7) Specified Link Length Units 6000-D01 L (km) Channel Plan Models 6000-D02 6000-D03 Comments 6000-D04 40 40 40 40 NTSC 80-Ch PAL 60-Ch NTSC 110-ch PAL 89-Ch Optical Output Power Po (dBm) 11.0 11.0 11.0 11.0 Noise Bandwidth BW (MHz) 4 5 4 5 Min. SBS Suppression (dBm) > 12.0 >12.0 >12.0 >12.0 Min. Carrier to Noise Ratio CNR (dB) 54.0 54.0 51.0 51.0 Min. Composite Second Order CSO (dBc) -65 -65 -65 -65 Max. Composite Triple Beat CTB (dBc) -65 -65 -65 -65 Max. @ +25°C Composite Triple Beat CTB (dBc) -64 -64 -64 -64 Max. @ 0 C to 50 C o o S-Type Property Performance (Note 1-7) Specified Link Length Units 6000-SA1 L (km) Channel Plan 6000-SA2 Models 6000-SA3 6000-SA4 Comments 6000-SA5 65 65 65 65 65 NTSC 80 PAL 60 NTSC 110 PAL 89 42 CENELEC Min. - Higher Powers Available See Chart Optical Output Power Po (dBm) 7.0/ 7.0 7.0/ 7.0 7.0/ 7.0 7.0/ 7.0 7.0/ 7.0 Noise Bandwidth BW (MHz) 4 5 4 5 5 SBS Suppression (dBm) 16.0 16.0 16.0 16.0 16.0 Min. Carrier to Noise Ratio CNR (dB) 53.0/ 53.0 53.0/ 53.0 50.0/ 50.0 50.0/ 50.0 53.0/ 53.0 Min. Composite Second Order CSO (dBc) -65/ -65 -65/ -65 -65/ -65 -65/ -65 -65/ -65 Max. Composite Triple Beat CTB (dBc) -65 -65 -65 -65 -65 Max. @ +25°C Composite Triple Beat CTB (dBc) -64 -64 -64 -64 -64 Max. @ 0 C to 50 C o | REV 2013.10 Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice. o Medallion 6000 Series 1550 nm Externally-Modulated Transmitter FIBER OPTICS DATASHEET | OCTOBER 2013 F-type Property Performance (Note 1-7) Specified Link Length Units 6000-F01 L (km) Channel Plan Optical Output Power Po (dBm) 6000-F02 Models 6000-F03 Comments 6000-F04 20 20 20 20 NTSC 80-Ch PAL 60-Ch NTSC 110-ch PAL 89-Ch 7.0/ 7.0 7.0/ 7.0 7.0/ 7.0 7.0/ 7.0 Min. Noise Bandwidth BW (MHz) 4 5 4 5 SBS Suppression (dBm) 21.0 21.0 21.0 21.0 Min. Carrier to Noise Ratio CNR (dB) 48.0 48.0 45.0 45.0 Min. Composite Second Order CSO (dBc) -58 -58 -58 -58 Max. Composite Triple Beat CTB (dBc) -58 -58 -58 -58 Max. N-Type Property Performance (Note 1-7) Specified Link Length Units 6000-N01 L (km) Channel Plan Models 6000-N02 40 40 NTSC 80-Ch PAL 60-Ch Comments Optical Output Power Po (dBm) 9.5 9.5 Noise Bandwidth BW (MHz) 4 5 Min. SBS Suppression (dBm) 13.0 13.0 Min. Carrier to Noise Ratio CNR (dB) 52.0 52.0 Min. Composite Second Order CSO (dBc) -62 -62 Max. Composite Triple Beat CTB (dBc) -62 -62 Max. @ +25°C Composite Triple Beat CTB (dBc) -61 -61 Max. @ 0 C to 50 C o o Notes: 1. Unless stated otherwise all specifications apply over full temperature range with no digital loading. 2. Unless stated otherwise specifications apply for nominal RF input level as defined below, after a 30 minute stabilization period. 3. Specifications separated by a slash are port1 / port 2. 4. Units are tested per the Test / Link Configuration Table 5. Noise figure for the EDFA = 4.5 ~ 5.5 dB 6. Corning SMF-28 single mode fiber 7. Receiver responsivity is 0.95 mA/mW, Equivalent noise current is 7 pA/(Hz)1/2 8. With 36 QPSK modulated SAT-IF signals between 950 … 2800 MHz. 27 MHz IF bandwidth | REV 2013.10 Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice. Medallion 6000 Series 1550 nm Externally-Modulated Transmitter FIBER OPTICS DATASHEET | OCTOBER 2013 General and Mechanical Specifications Property Requirement Comments Wavelength 1550 +/-5 nm Various Options + ITU-grid available – see Model Number Information Channel Plan Various – See Specification Tables Custom channel plans available Optical Connector SC/APC Other styles available 100 Base-T Ethernet (SNMP) Rear Panel RS-232 interface VFD Screen Front Panel Controls VFD- (Vacuum Fluorescent Display) Monitoring Interfaces Operating Temperature 0°C to 50°C Storage Temperature -20°C to 70°C Power Consumption 65 W max Agency Listings EMI: EN50083-2:2006 (US CATV) EN55022:2006 (US IT) EN61000-3-2 (Harmonics) EN61000-3-3 (Flicker) FCC: Part 15, Subpart B, class “A” Unintentional Radiators ICES-003 (Canada) AN/NZS 3548, Class A (Australia) VCCI, Class A (Japan) Transportation Vibration GR-2853-CORE In Shipping package Transportation Shock GR-2853-CORE In Shipping package Operating Humidity 20% to 85% Non-condensing Supply Range (VAC) Safety: FDA/CDRH Laser Safety Governed by Code of Federal Regulations Title 21, Volume 8, Part 1040 IEC 60950-1 IEC 60728-11 Laser IEC 60825-1 CB Certification 90 to 265 VAC, 50/60 Hz Dimensions 19.0”W x 15.0”D x 1.72”H (width includes 19” front panel ears, depth includes, connectors, fans & front panel) – see drawing Input Power Range 17 +/-1 dBmV/ch 80 NTSC channels Manual mode Input Power Range 15 +/-1 dBmV/ch 110 NTSC channels Manual mode 18 +/-1 dBmV/ch 60 PAL channels Manual mode 20 +/-1 dBmV/ch 42 CENELEC channels Manual mode 16 +/-1 dBmV/ch 89 PAL channels Manual mode 27 +/-1 dBmV/ch SAT-IF channels Manual mode 19 +/-2 dBmV/ch 80 NTSC channels CW mode 17 +/-2 dBmV/ch 110 NTSC channels CW mode 20 +/-2 dBmV/ch 60 PAL channels CW mode 18 +/-2 dBmV/ch 89 PAL channels CW mode 22 +/-2 dBmV/ch 42 CENELEC channels CW mode 29 +/-2 dBmV/ch SAT-IF channels AGC mode | REV 2013.10 Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice. Medallion 6000 Series 1550 nm Externally-Modulated Transmitter FIBER OPTICS DATASHEET | OCTOBER 2013 General and Mechanical Specifications (continued) Property Requirement Front Panel RF Gain / OMI Adjustment Range Comments +2 / -4 dB from nominal setting CATV Performance can vary slightly CATV Frequency Range 45 MHz – 1003 MHz CATV Flatness +/- 0.50 dB 45 MHz – 550 MHz +/- 0.75 dB 45 MHz – 1003 MHz CATV Flatness – N-Type +/- 0.75 dB 45 MHz – 1003 MHz N-Type CATV Input impedance 75 Ω CATV Input Return Loss 16 dB min CATV Front Panel RF Tap -20 +/- 1 dB down from RF input 45 MHz – 1003 MHz CATV Front Panel RF Tap Flatness +/- 1 dB SAT-IF Frequency Range 950 MHz – 2800 MHz 45 MHz – 1003 MHz SAT-IF Flatness +/- 2 dB SAT-IF Input impedance 75 Ω SAT-IF Input Return Loss 10 dB min SAT-IF Front Panel RF Tap 7 +/- 2.5 dBmV/Ch at 1% OMI/ch SAT-IF Front Panel RF Tap Flatness +/- 1 dB 950 MHz – 2800 MHz 950 MHz – 2800 MHz Test/Link Configuration Property Link1 EDFA Received Power2 L-Type 15 dBm 25 Km 0.0 dBm at the receiver D-Type None 40 Km 0.0 dBm at the receiver S-Type 16 dBm 65 Km 0.0 dBm at the receiver F-Type 21 dBm 20 Km -5.5 dBm at the receiver N-Type 13 dBm 40 Km 0.0 dBm at the receiver | REV 2013.10 Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice. Medallion 6000 Series 1550 nm Externally-Modulated Transmitter DATASHEET | OCTOBER 2013 FIBER OPTICS Outline Drawing (Dimensions in inches) Laser Safety Information This product meets the applicable requirements of 21 CFR 1010 & 1040 and is classified as a Class 1M laser product. During use as intended, the laser energy is fully contained within the fiber network such that there is no accessible laser radiation. This product has been issued accession number 0820466-001. | REV 2013.10 Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice. Medallion 6000 Series 1550 nm Externally-Modulated Transmitter FIBER OPTICS DATASHEET | OCTOBER 2013 Model Number Information (note 3) 6000 – Logo & Customer Specific □□□ □-□ □□□□ Pout (dBm min) Note 1 Link type Loading Type Optics RF 0– EMCORE Logo D – 40 km 0 – for D, and F-Types 1 – NTSC (80-ch) 1 – SC/APC, Rear 1 – no Logo S – 65 km A – 7.0/7.0 for S-Type 2 – PAL (60-ch) 2 – FC/APC, Rear B – 8.0/8.0 for S-Type 3 – NTSC (110-ch) 3 – E2000/APC, Rear 3 – RF IN Front, TP Rear C – 10.0 for S-Type 4 – PAL (89-ch) 4 – SC/APC, Front 4 – RF IN Rear, TP Rear D- 10/10 for S & L-Type 5 – Not Used E – 8.5/8.5 for L Type 6 – CENELEC (42ch) F – FTTx SBS 20 dBm L – 25 km N – 40 km Note 4 Note 5 5 – FC/APC, Front 1 – RF IN Rear, TP Front 2 – RF IN Front, TP Front Wavelength (nm) Power Supply 00 –1555+/5.0nm 1 – AC primary, no secondary 01 – 1550+/5.0nm 2 – DC primary, no secondary xx – ITU Channel +/Note 2 0.1nm 3 – AC primary, AC secondary 4 – AC primary, DC secondary 5 – DC primary, DC secondary 6 – E2000/APC, Front Note 1: Options available for Indicated Types only. Note 2: ITU grid wavelengths can be specified from channel 18 to 40. Note 3: Not all configurations are available, contact factory. Note 4: Available for S and L Links. CSO port 2 degraded by 1dB for Channel Loads 1 and 2, CSO port 2 degraded by 2 dB for Channel Loads 3 and 4. Note 5: Contact Factory for Model type availability Additional Kits G3708-006-001 - Replaceable AC power supply modules G3708-005-001 - Replaceable DC power supply modules G7914-076-001 - Replaceable Blank power module plate G3906-008-001 - Replaceable fans | REV 2013.10 Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.