a CMOS Single Supply Rail-to-Rail Input/Output Operational Amplifiers with Shutdown AD8591/AD8592/AD8594 FEATURES Single Supply Operation: +2.5 V to +6 V High Output Current: ⴞ250 mA Extremely Low Shutdown Supply Current: 100 nA Low Supply Current: 750 A/Amp Wide Bandwidth: 3 MHz Slew Rate: 5 V/s No Phase Reversal Very Low Input Bias Current High Impedance Outputs When in Shutdown Mode Unity Gain Stable APPLICATIONS Mobile Communication Handset Audio PC Audio PCMCIA/Modem Line Driving Battery Powered Instrumentation Data Acquisition ASIC Input or Output Amplifier LCD Display Reference Level Driver GENERAL DESCRIPTION The AD8591, AD8592 and AD8594 are single, dual and quad rail-to-rail input and output single supply amplifiers featuring 250 mA output drive current and a power saving shutdown mode. The AD8592 includes an independent shutdown function for each amplifier. When both amplifiers are in shutdown mode the total supply current is reduced to less than 1 µA. The AD8591 and AD8594 include a single master shutdown function that reduces total supply current to less than 1 µA. All amplifier outputs are in a high impedance state when in shutdown mode. These amplifiers have very low input bias currents, making them suitable for integrators and diode amplification. Outputs are stable with virtually any capacitive load. Supply current is less than 750 µA per amplifier in active mode. Applications for these amplifiers include audio amplification for portable computers, portable phone headsets, sound ports, sound cards and set-top boxes. The AD859x family is capable of driving heavy capacitive loads such as LCD panel reference levels. The ability to swing rail-to-rail at both the input and output enables designers to buffer CMOS DACs, ASICs and other wide output swing devices in single supply systems. PIN CONFIGURATIONS 6-Lead SOT (RT Suffix) 6 OUT A 1 V2 2 AD8591 V1 5 SD 1IN A 3 4 2IN A 10-Lead SOIC (RM Suffix) 10 V+ OUT A 1 9 OUT B –IN A 2 +IN A 3 V– 4 7 +IN B SDA 5 6 SDB AD8592 8 (Not to Scale) –IN B 16-Lead Narrow SOIC (R Suffix) OUT A 1 16 OUT D 2IN A 2 15 2IN D 14 1IN D 1IN A 3 V1 4 AD8594 13 V2 TOP VIEW 1IN B 5 (Not to Scale) 12 1IN C 2IN B 6 11 2IN C OUT B 7 10 OUT C NC 8 9 SD NC = NO CONNECT 16-Lead TSSOP (RU Suffix) OUT A 2IN A 1IN A V1 1IN B 2IN B OUT B NC 1 16 AD8594 8 9 OUT D 2IN D 1IN D V2 +IN C 2IN C OUT C SD NC = NO CONNECT The AD8591, AD8592 and AD8594 are specified over the industrial (–40°C to +85°C) temperature range. The AD8591, single, is available in the tiny 6-lead SOT package. The AD8592, dual, is available in the 10-lead µSOIC surface mount package. The AD8594, quad, is available in 16-lead narrow SOIC and 16-lead TSSOP packages. REV. A Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781/329-4700 World Wide Web Site: http://www.analog.com Fax: 781/326-8703 © Analog Devices, Inc., 1999 AD8591/AD8592/AD8594–SPECIFICATIONS ELECTRICAL CHARACTERISTICS (V = +2.7 V, V S Parameter Symbol INPUT CHARACTERISTICS␣ Offset Voltage VOS CM = +1.35 V, TA = +25ⴗC unless otherwise noted) Conditions Min Typ –40°C < TA < +85°C Input Bias Current IB 5 –40°C < TA < +85°C Input Offset Current 1 IOS –40°C < TA < +85°C Input Voltage Range Common-Mode Rejection Ratio Large Signal Voltage Gain Offset Voltage Drift Bias Current Drift Offset Current Drift OUTPUT CHARACTERISTICS Output Voltage High CMRR AVO ∆VOS /∆T ∆IB /∆T ∆IOS /∆T VCM = 0 V to +2.7 V RL = 2 kΩ , VO = +0.3 V to +2.4 V VOH IL = 10 mA –40°C to +85°C IL = 10 mA –40°C to +85°C Output Voltage Low VOL Output Current Open-Loop Impedance IOUT ZOUT POWER SUPPLY␣ Power Supply Rejection Ratio Supply Current/Amplifier 0 38 +2.55 +2.5 45 ISD1 ISD2 SHUTDOWN INPUTS Logic High Voltage Logic Low Voltage Logic Input Current VINH VINL IIN –40°C < TA < +85°C –40°C < TA < +85°C –40°C < TA < +85°C +1.6 DYNAMIC PERFORMANCE␣ Slew Rate Settling Time Gain Bandwidth Product Phase Margin Channel Separation SR tS GBP Φo CS RL = 2 kΩ To 0.01% NOISE PERFORMANCE␣ Voltage Noise Density en Current Noise Density in Supply Current Shutdown Mode ISD 25 30 50 60 25 30 +2.7 mV mV pA pA pA pA V dB V/mV µV/°C fA/°C fA/°C +2.61 ± 250 60 VS = +2.5 V to +6 V VO = 0 V –40°C < TA < +85°C All Amplifiers Shut Down –40°C < TA < +85°C Amplifier 1 Shut Down (AD8592) Amplifier 2 Shut Down (AD8592) PSRR ISY Units 45 25 20 50 20 60 f = 1 MHz, AV = 1 Max 100 125 55 0.1 V V mV mV mA Ω 1 1.25 1 1 1.4 1.4 dB mA mA µA µA mA mA +0.5 1 V V µA f = 1 kHz, RL = 2 kΩ 3.5 1.4 2.2 67 65 V/µs µs MHz Degrees dB f = 1 kHz f = 10 kHz f = 1 kHz 45 30 0.05 nV/√Hz nV/√Hz pA/√Hz Specifications subject to change without notice. –2– REV. A AD8591/AD8592/AD8594 ELECTRICAL CHARACTERISTICS (V = +5.0 V, V S Parameter Symbol INPUT CHARACTERISTICS␣ Offset Voltage VOS CM = +2.5 V, TA = +25ⴗC unless otherwise noted) Conditions Min Typ Max Units 2 25 30 50 60 25 30 +5 mV mV pA pA pA pA V dB V/mV µV/°C fA/°C fA/°C –40°C < TA < +85°C Input Bias Current IB 5 –40°C < TA < +85°C Input Offset Current 1 IOS –40°C < TA < +85°C Input Voltage Range Common-Mode Rejection Ratio Large Signal Voltage Gain Offset Voltage Drift Bias Current Drift Offset Current Drift OUTPUT CHARACTERISTICS Output Voltage High CMRR AVO ∆VOS /∆T ∆IB /∆T ∆IOS /∆T VCM = 0 V to +5 V RL = 2 kΩ , VO = +0.5 V to +4.5 V –40°C < TA < +85°C VOH IL = 10 mA –40°C to +85°C IL = 10 mA –40°C to +85°C Output Voltage Low VOL Output Current Open-Loop Impedance IOUT ZOUT POWER SUPPLY␣ Power Supply Rejection Ratio Supply Current/Amplifier 0 38 15 +4.9 +4.85 ± 250 40 f = 1 MHz, AV = 1 45 ISD1 ISD2 SHUTDOWN INPUTS Logic High Voltage Logic Low Voltage Logic Input Current VINH VINL IIN –40°C < TA < +85°C –40°C < TA < +85°C –40°C < TA < +85°C +2.4 DYNAMIC PERFORMANCE␣ Slew Rate Full-Power Bandwidth Settling Time Gain Bandwidth Product Phase Margin Channel Separation SR BWP tS GBP Φo CS RL = 2 kΩ 1% Distortion To 0.01% NOISE PERFORMANCE␣ Voltage Noise Density en Current Noise Density in Supply Current-Shutdown Mode ISD 100 125 55 0.1 V V mV mV mA Ω 1.25 1.75 1 1 1.6 1.6 dB mA mA µA µA mA mA +0.8 1 V V µA f = 1 kHz, RL = 10 kΩ 5 325 1.6 3 70 65 V/µs kHz µs MHz Degrees dB f = 1 kHz f = 10 kHz f = 1 kHz 45 30 0.05 nV/√Hz nV/√Hz pA/√Hz Specifications subject to change without notice. REV. A +4.94 50 VS = +2.5 V to +6 V VO = 0 V –40°C < TA < +85°C All Amplifiers Shut Down –40°C < TA < +85°C Amplifier 1 Shut Down (AD8592) Amplifier 2 Shut Down (AD8592) PSRR ISY 47 30 20 50 20 –3– AD8591/AD8592/AD8594 ABSOLUTE MAXIMUM RATINGS 1 Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +6 V Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GND to VS Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . ± 6 V Output Short Circuit2 Duration to GND . . . . . . . . . . . . Observe Derating Curves Storage Temperature Range R, RT, RM, RU Packages . . . . . . . . . . . . –65°C to +150°C Operating Temperature Range AD8591/AD8592/AD8594 . . . . . . . . . . . . –40°C to +85°C Junction Temperature Range R, RT, RM, RU Packages . . . . . . . . . . . . –65°C to +150°C Lead Temperature Range (Soldering, 60 sec) . . . . . . . +300°C Package Type JA1 JC Units 6-Lead SOT-23 (RT) 10-Lead µSOIC (RM) 16-Lead SOIC (R) 16-Lead TSSOP (RU) 230 200 120 180 92 44 36 35 °C/W °C/W °C/W °C/W NOTE 1 θJA is specified for worst case conditions, i.e., θJA is specified for device in socket for surface mount packages. ORDERING GUIDE NOTES 1 Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those listed in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. 2 For supplies less than ± 5 V the differential input voltage is limited to the supplies. Model Temperature Range Package Description Package Option AD8591ART AD8592ARM AD8594AR AD8594ARU –40°C to +85°C –40°C to +85°C –40°C to +85°C –40°C to +85°C 6-Lead SOT-23 10-Lead µSOIC 16-Lead SOIC 16-Lead TSSOP RT-6 RM-10 R-16A RU-16 CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the AD8591/AD8592/AD8594 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. WARNING! ESD SENSITIVE DEVICE Typical Performance Characteristics 10k 1k SINK 10 1 0.1 0.01 0.1 1 10 100 LOAD CURRENT – mA 1k Figure 1. Output Voltage to Supply Rail vs. Load Current SUPPLY CURRENT/AMPLIFIER – mA ∆OUTPUT VOLTAGE – mV ∆OUTPUT VOLTAGE – mV 100 SOURCE 0.90 VS = +5V TA = +258C VS = +2.7V TA = +258C 1k 100 SOURCE SINK 10 1 0.1 0.01 0.1 100 1 10 LOAD CURRENT – mA 1k Figure 2. Output Voltage to Supply Rail vs. Load Current –4– 0.85 0.80 0.75 0.70 VS = +5V 0.65 0.60 VS = +2.7V 0.55 0.50 240 220 0 20 40 60 TEMPERATURE – 8C 80 100 Figure 3. Supply Current per Amplifier vs. Temperature REV. A AD8591/AD8592/AD8594 22 0.5 0.4 0.3 0.2 0.1 0.75 1.25 1.75 2.25 2.75 SUPPLY VOLTAGE – 6Volts 26 27 235 215 5 25 45 TEMPERATURE – 8C 1 0 21 22 250 235 215 5 25 45 TEMPERATURE – 8C Figure 7. Input Offset Current vs. Temperature 135 0 180 10k 100k 1M 10M FREQUENCY – Hz 100M Figure 10. Open-Loop Gain and Phase vs. Frequency 85 65 VS = +2.7V RL = NO LOAD TA = +258C 45 40 90 20 135 0 180 2 0 1 2 3 4 COMMON-MODE VOLTAGE – Volts 5 1k 3 2 1 0 1k 10k 100k 1M 10M FREQUENCY – Hz 100M Figure 9. Open-Loop Gain and Phase vs. Frequency 5 VS = +2.7V RL = 2kV TA = +258C VIN = 2.5V p-p 4 OUTPUT SWING – V p-p 20 PHASE SHIFT – Degrees 90 215 5 25 45 TEMPERATURE – 8C 3 45 40 REV. A 4 5 VS = +5V RL = NO LOAD TA = +258C 60 1k 5 Figure 8. Input Bias Current vs. Common-Mode Voltage 80 235 60 6 1 85 65 4 80 GAIN – dB INPUT BIAS CURRENT – pA 2 5 Figure 6. Input Bias Current vs. Temperature VS = +5V TA = +258C 7 3 6 2 250 85 65 8 VS = +2.7V, +5V VCM = VS / 2 7 3 Figure 5. Input Offset Voltage vs. Temperature 4 INPUT OFFSET CURRENT – pA 25 28 250 3 Figure 4. Supply Current per Amplifier vs. Supply Voltage GAIN – dB 24 4 OUTPUT SWING – V p-p 0 23 PHASE SHIFT – Degrees 0.6 VS = +2.7V, +5V VCM = VS/2 INPUT BIAS CURRENT – pA 0.7 8 VS = +5V VCM = +2.5V TA = +258C INPUT OFFSET VOLTAGE – mV SUPPLY CURRENT/AMPLIFIER – mA 0.8 VS = +5V RL = 2kV TA = +258C VIN = 4.9V p-p 3 2 1 10k 100k 1M FREQUENCY – Hz 10M Figure 11. Closed-Loop Output Voltage Swing vs. Frequency –5– 0 1k 10k 100k 1M FREQUENCY – Hz 10M Figure 12. Closed-Loop Output Voltage Swing vs. Frequency AD8591/AD8592/AD8594 110 200 140 100 80 CMRR – dB 90 120 AV = 10 100 80 80 40 240 10k 100k 1M 10M FREQUENCY – Hz 50 1k 100M 260 100 10M 100k 1M FREQUENCY – Hz 2PSRR +PSRR 40 20 0 220 240 1k 10k 100k FREQUENCY – Hz 1M Figure 16. Power Supply Rejection Ratio vs. Frequency +OS 40 2OS 30 20 10 0 10 10M 10k 100k FREQUENCY – Hz 1M 10M 60 VS = +2.5V RL = 2kV TA = +258C SMALL SIGNAL OVERSHOOT – % 80 SMALL SIGNAL OVERSHOOT – % 100 50 1k Figure 15. Power Supply Rejection Ratio vs. Frequency 60 VS = +5V TA = +258C 120 PSRR – dB 10k Figure 14. Common-Mode Rejection Ratio vs. Frequency 140 260 100 2PSRR 20 220 60 Figure 13. Closed-Loop Output Impedance vs. Frequency 60 +PSRR 40 0 20 0 1k 60 70 AV = 1 60 VS = +2.5V TA = +258C 120 100 160 IMPEDANCE – V 140 VS = +5V TA = +258C PSRR – dB 180 VS = +5V TA = +258C 100 1k CAPACITANCE – pF 10k Figure 17. Small Signal Overshoot vs. Load Capacitance 50 VS = +5V RL = 2kV TA = +258C 40 2OS 30 +OS 20 10 0 10 100 1k CAPACITANCE – pF 10k Figure 18. Small Signal Overshoot vs. Load Capacitance VS = 61.35V AV = 1 100 90 RL = 2kV 0V VS = 61.35V VIN = 650mV AV = 1 RL = 2kV CL = 300pF TA = +258C 500 ns/DIV Figure 19. Small Signal Transient Response 20mV/DIV 20mV/DIV TA = +258C 0V VS = 62.5V VIN = 650mV AV = 1 RL = 2kV CL = 300pF TA = +258C 10 0% 500mV 500ns 500 ns/DIV Figure 20. Small Signal Transient Response –6– Figure 21. Large Signal Transient Response REV. A AD8591/AD8592/AD8594 100 90 10ms 1V 100 RL = 2kV 90 TA = +258C VS = 62.5V AV = 1 10 10 0% 0% 500mV TA = +258C 1V 500ns CURRENT NOISE DENSITY – pA/ Hz 1 VS = 62.5V AV = 1 VS = +5V TA = +258C 0.1 0.01 10 100mV/DIV 90 VS = +5V AV = 1000 TA = +258C FREQUENCY = 1kHz 100 90 10 10 0% 0% 1k 10k FREQUENCY – Hz 100k Figure 24. Current Noise Density vs. Frequency VS = +5V A V = 1000 500 TA = +258C FREQUENCY = 10kHz 200mV/DIV 100 Figure 23. No Phase Reversal QUANTITY – Amplifiers Figure 22. Large Signal Transient Response 100 VS = +2.7V VCM = +1.35V TA = +258C 400 300 200 100 MARKER 25.9 mV/ Hz MARKER 41mV/ Hz –12 –10 –8 –6 –4 –2 0 2 4 INPUT OFFSET VOLTAGE – mV Figure 25. Voltage Noise Density vs. Frequency Figure 26. Voltage Noise Density vs. Frequency VS = +5V VCM = +2.5V TA = +258C QUANTITY – Amplifiers 500 400 300 200 100 –12 –10 –8 –6 –4 –2 0 2 4 INPUT OFFSET VOLTAGE – mV Figure 28. Input Offset Voltage Distribution REV. A –7– Figure 27. Input Offset Voltage Distribution AD8591/AD8592/AD8594 AD8591/AD8592/AD8594 APPLICATION SECTION Theory of Operation Output Phase Reversal The AD8591/AD8592/AD8594 are immune to output voltage phase reversal with an input voltage within the supply voltages of the device. However, if either of the device’s inputs exceeds +0.6␣ V outside of the supply rails, the output could exhibit phase reversal. This is due to the ESD protection diodes becoming forward biased, thus causing the polarity of the input terminals of the device to switch. The AD859x family of amplifiers are all CMOS, high output drive, rail-to-rail input and output single supply amplifiers designed for low cost and high output current drive. The parts include a power saving shutdown function making the AD8591/AD8592/AD8594 op amps ideal for portable multimedia and telecom applications. Figure 29 shows the simplified schematic for an AD8591/AD8592/ AD8594 amplifier. Two input differential pairs, consisting of an n-channel pair (M1-M2) and a p-channel pair (M3-M4), provide a rail-to-rail input common-mode range. The outputs of the input differential pairs are combined in a compound folded-cascode stage, which drives the input to a second differential pair gain stage. The outputs of the second gain stage provide the gate voltage drive to the rail-to-rail output stage. The technique recommended in the Input Overvoltage Protection section should be applied in applications where the possibility of input voltages exceeding the supply voltages exists. Output Short Circuit Protection To achieve high output current drive and rail-to-rail performance, the outputs of the AD859x family do not have internal short circuit protection circuitry. Although these amplifiers are designed to sink or source as much as 250␣ mA of output current, shorting the output directly to the positive supply could damage or destroy the device. To protect the output stage, the maximum output current should be limited to ± 250␣ mA. The rail-to-rail output stage consists of M15 and M16, which are configured in a complementary common-source configuration. As with any rail-to-rail output amplifier, the gain of the output stage, and thus the open-loop gain of the amplifier, is dependent on the load resistance. Also, the maximum output voltage swing is directly proportional to the load current. The difference between the maximum output voltage to the supply rails, known as the dropout voltage, is determined by the AD8591/AD8592/ AD8594 output transistors’ on-channel resistance. The output dropout voltage is given in Figure 1 and Figure 2. * * M337 M5 M3 M30 M8 VB2 M1 20mA M12 M4 VSY 250 mA (2) For a +5 V single supply application, RX should be at least 20␣ Ω. Because RX is inside the feedback loop, VOUT is not affected. The tradeoff in using RX is a slight reduction in output voltage swing under heavy output current loads. RX will also increase the effective output impedance of the amplifier to RO + RX, where RO is the output impedance of the device. * * 100mA M11 INV SD RX ≥ V+ 100mA 50mA By placing a resistor in series with the output of the amplifier as shown in Figure 30, the output current can be limited. The minimum value for RX can be found from Equation 2. +5V M15 IN– M6 IN+ VB3 20mA M7 AD8592 M16 M9 INV M340 * 50mA VIN OUT M2 M10 * M13 Figure 30. Output Short Circuit Protection M31 Power Dissipation Although the AD859x family of amplifiers are able to provide load currents of up to 250␣ mA, proper attention should be given to not exceeding the maximum junction temperature for the device. The equation for finding the junction temperature is given as: *NOTE: ALL CURRENT SOURCES GO TO 0 mA IN SHUTDOWN MODE Figure 29. AD8591/AD8592/AD8594 Simplified Schematic TJ = PDISS × θ JA + TA Input Voltage Protection Although not shown on the simplified schematic, ESD protection diodes are connected from each input to each power supply rail. These diodes are normally reverse biased, but will turn on if either input voltage exceeds either supply rail by more than +0.6 V. Should this condition occur, the input current should be limited to less than ± 5 mA. This can be done by placing a resistor in series with the input(s). The minimum resistor value should be: VIN , MAX 5 mA VOUT M14 V– RIN ≥ RX 20V (3) Where TJ = AD859x junction temperature PDISS = AD859x power dissipation θJA = AD859x junction-to-ambient thermal resistance of the package; and TA = The ambient temperature of the circuit (1) –8– REV. A AD8591/AD8592/AD8594 In any application, the absolute maximum junction temperature must be limited to +150°C. If this junction temperature is exceeded, the device could suffer premature failure. If the output voltage and output current are in phase, for example, with a purely resistive load, the power dissipated by the AD859x can be found as: ( PDISS = I LOAD × VSY – VOUT Where ) 50mV 100 47nF LOAD ONLY (4) SNUBBER IN CIRCUIT 10ms Figure 33. Snubber Network Reduces Overshoot and Ringing Caused from Driving Heavy Capacitive Loads By calculating the power dissipation of the device and using the thermal resistance value for a given package type, the maximum allowable ambient temperature for an application can be found using Equation 3. The optimum values for the snubber network should be determined empirically based on the size of the capacitive load. Table I shows a few sample snubber network values for a given load capacitance. Capacitive Loading Table I. Snubber Networks for Large Capacitive Loads The AD859x exhibits excellent capacitive load driving capabilities and can drive up to 10 nF directly. Although the device is stable with large capacitive loads, there is a decrease in amplifier bandwidth as the capacitive load increases. Figure 31 shows a graph of the AD8592 unity gain bandwidth under various capacitive loads. 4 VS = 62.5V Load Capacitance (CL) Snubber Network (RS, CS) 0.47 nF 4.7 nF 47 nF 300 Ω, 0.1 µF 30 Ω, 1 µF 5 Ω, 1 µF RL = 1kV A PC-98 Compliant Headphone/Speaker Amplifier TA = +258C Because of its high output current performance and shutdown feature, the AD8592 makes an excellent amplifier for driving an audio output jack in a computer application. Figure 34 shows how the AD8592 can be interfaced with an AC97 codec to drive headphones or speakers. 3 BANDWIDTH – MHz 10 0% 50mV ILOAD = AD859x output load current VSY = AD859x supply voltage; and VOUT = The output voltage 3.5 90 2.5 2 +5V 1.5 +5V VDD 1 VDD 28 U1-A 0.5 LEFTOUT 35 0 0.01 0.1 1 CAPACITIVE LOAD – nF Figure 31. Unity Gain Bandwidth vs. Capacitive Load C2 100mF 7 U1-B 8 NOTE: ADDITIONAL PINS OMITTED FOR CLARITY NC 9 R5 20V R3 2kV U1 = AD8592 Figure 34. A PC-98 Compliant Headphone/Line Out Amplifier When headphones are plugged into the jack, the normalizing contacts disconnect from the audio contacts. This allows the voltage to the AD8592 shutdown pins to be pulled up to +5 V, activating the amplifiers. With no plug in the output jack, the shutdown voltage is pulled to 100 mV through the R1 and R3␣ +␣ R5 voltage divider. This powers the AD8592 down when it is not needed, saving current from the power supply or battery. VOUT CL 47nF Figure 32. Configuration for Snubber Network to Compensate for Capacitive Loads REV. A R2 2kV R1 100kV VSS RS 5V CS 1mF +5V R4 20V 6 RIGHTOUT 36 +5V AD8592 1 5 AD1881 (AC97) When driving heavy capacitive loads directly from the AD859x output, a snubber network can be used to improve transient response. This network consists of a series R-C connected from the amplifier’s output to ground, placing it in parallel with the capacitive load. The configuration is shown in Figure 32. Although this network will not increase the bandwidth of the amplifier, it will significantly reduce the amount of overshoot, as shown in Figure 33. VIN 100mV p-p 4 3 100 10 C1 100mF 10 2 –9– AD8591/AD8592/AD8594 If gain is required from the output amplifier, four additional resistors should be added as shown in Figure 35. The gain of the AD8592 can be set as: AV = R7 R6 A Combined Microphone and Speaker Amplifier for Cellphone and Portable Headsets (5) +5V The dual amplifiers in the AD8592 make an efficient design for interfacing with a headset containing a microphone and speaker. Figure 36 demonstrates a simple method for constructing an interface to a codec. R7 20kV VDD LEFTOUT 35 R1 2.2kV +5V VDD 38 R6 10kV C1 100mF 10 2 U1-A R4 20V 1 4 3 +5V 5 R2 2kV C1 0.1mF R6 10kV RIGHTOUT 36 U1-B 9 8 U1-A 3 R7 1kV MIC + SPEAKER JACK 5 +5V R8 100kV VREF FROM CODEC 6 C2 10mF R5 20V 7 9 NOTE: ADDITIONAL PINS OMITTED FOR CLARITY AV = R3 2kV U1 = AD8592 (RIGHT OUT) Figure 36. A Speaker/Mic Headset Amplifier Circuit = +6dB WITH VALUES SHOWN R6 U1-A is used as a microphone preamplifier, where the gain of the preamplifier is set as R3/R2. R1 is used to bias an electret microphone and C1 blocks any dc voltages from the amplifier. U1-B is the speaker amplifier, and its gain is set at R5/R4. To sum a stereo output, R6 should be added, equal in value to R4. Using the same principle as described in the previous section, the normalizing contact on the microphone/speaker jack can be used to put the AD8592 into shutdown when the headset is not plugged in. The AD8592 shutdown inputs can also be controlled with TTL or CMOS compatible logic, allowing microphone or speaker muting if desired. R4 and R5 help protect the AD8592 output in case the output jack or headphone wires accidentally get shorted to ground. The output coupling capacitors C1 and C2 block dc current from the headphones and create a high-pass filter with a corner frequency of: ( 2π C1 R4 + RL R6 10kV (OPTIONAL) U1 = AD8592 Input coupling capacitors are not required for either circuit as the reference voltage is supplied from the AD1881. 1 FROM CODEC MONO OUT (OR LEFT OUT) 8 Figure 35. A PC-98 Compliant Headphone/Line Out Amplifier With Gain f –3 dB = R4 10kV U1-B R5 10kV R7 TO CODEC 1 4 VSS R7 20kV 10 2 6 7 +5V NC VREF 27 C2 100mF R2 10kV NC R1 100kV AD1881 (AC97) R3 100kV +5V ) Where RL is the resistance of the headphones. An Inexpensive Sample-and-Hold Circuit (6) The independent shutdown control of each amplifier in the AD8592 allows a degree of flexibility in circuit design. One particular application for which this feature is useful is in designing a sample-and-hold circuit for data acquisition. Figure 37 shows a schematic of a simple, yet extremely effective sample-and-hold circuit using a single AD8592 and one capacitor. 8 +5V 2 10 U1-B U1-A VIN 4 3 5 SAMPLE CLOCK 1 C1 1nF 7 6 9 SAMPLE AND HOLD OUTPUT +5V U1 = AD8592 Figure 37. An Efficient Sample-and-Hold Circuit –10– REV. A AD8591/AD8592/AD8594 The U1-A amplifier is configured as a unity gain buffer driving a 1 nF capacitor. The input signal is connected to the noninverting input, while the sample clock controls the shutdown for that amplifier. When the sample clock is high, the U1-A amplifier is active and the output follows VIN. Once the sample clock goes low, U1-A shuts down with the output of the amplifier going to a high impedance state, holding the voltage on the C1 capacitor. The U1-B amplifier is used as a unity gain buffer to prevent loading on C1. Because of the low input bias current of the U1-B CMOS input stage and the high impedance state of the U1-A output in shutdown, there is very little voltage droop from C1 during the Hold period. This circuit can be used with sample frequencies as high as 500␣ kHz and as low as below 1␣ Hz. Even lower voltage droop can be achieved for very low sample rates by increasing the value of C1. Single Supply Differential Line Driver Figure 39 shows a single supply differential line driver circuit that can drive a 600␣ Ω load with less than 0.7% distortion from 20 Hz to 15 kHz with an input signal of 4 V p-p and a single +5 V supply. The design uses an AD8594 to mimic the performance of a fully balanced transformer based solution. However, this design occupies much less board space while maintaining low distortion and can operate down to dc. Like the transformer based design, either output can be shorted to ground for unbalanced line driver applications without changing the circuit gain of 1. R3 10kV 3 R2 10kV Direct Access Arrangement for PCMCIA Modems (Telephone Line Interface) P1 Tx GAIN ADJUST TO TELEPHONE LINE 1:1 6.2V ZO 600V R2 9.09kV 1 R5 10kV 2 A1 C1 R1 10kV 0.1mF TRANSMIT TxA R6 10kV 9 6 8 7 R10 10kV R9 10kV 2 R11 10kV R12 10kV 3 5 A3 1 R13 R14 10kV 14.3kV 8 6 7 A4 P2 Rx GAIN ADJUST 2kV 9 7 R10 10kV 8 9 A1 4 R11 R12 10kV 10kV R9 100kV 8 7 A2 R8 100kV 7 9 R14 50V RL 600V C2 1mF C4 47mF R13 10kV VO2 SET: R6, R12, R13 = R3 Figure 39. A Low Noise, Single Supply Differential Line Driver R8 and R9 set up the common-mode output voltage equal to half of the supply voltage. C1 is used to couple the input signal and can be omitted if the input’s dc voltage is equal to half of the supply voltage. The circuit can also be configured to provide additional gain if desired. The gain of the circuit is: Where: R8 10kV RECEIVE RxA C2 0.1mF Figure 38. A Single Supply Direct Access Arrangement for PCMCIA Modems REV. A +5V 10 1 SET: R7, R10, R11 = R2 R7 10kV 10mF VO1 R6 10kV R7 10kV 4 GAIN = R3 R2 SHUTDOWN A2 3 10 A1 A1, A2 = 1/2 AD8592 +5V T1 MIDCOM 671-8005 2 C3 47mF +5V R1 10kV 3 5 6.2V A1, A2 = 1/2 AD8592 A3, A4 = 1/2 AD8592 VIN AV = 2kV R3 360V C1 22mF 1 A2 +5V Figure 38 illustrates a +5␣ V transmit/receive telephone line interface for 600␣ Ω systems. It allows full duplex transmission of signals on a transformer-coupled 600␣ Ω line in a differential manner. Amplifier A1 provides gain that can be adjusted to meet the modem output drive requirements. Both A1 and A2 are configured to apply the largest possible signal on a single supply to the transformer. Because of the AD8594’s high output current drive and low dropout voltages, the largest signal available on a single +5␣ V supply is approximately 4.5␣ V␣ p-p into a 600␣ Ω transmission system. Amplifier A3 is configured as a difference amplifier for two reasons: (1)␣ It prevents the transmit signal from interfering with the receive signal and (2)␣ it extracts the receive signal from the transmission line for amplification by A4. Amplifier A4’s gain can be adjusted in the same manner as A1’s to meet the modem’s input signal requirements. Standard resistor values permit the use of SIP (Single In-line Package) format resistor arrays. Couple this with the AD8594 16-lead TSSOP or SOIC footprint, and this circuit offers a compact, cost effective solution. R5 50V 2 –11– VOUT R3 = VIN R2 VOUT = VO1␣ –␣ VO2, R2 = R7 = R10 = R11 and, R3 = R6 = R12 = R13 (7) AD8591/AD8592/AD8594 SPICE Model for the AD8591/AD8592/AD8594 Amplifier The SPICE model for the AD8591/AD8592/AD8594 amplifier is one of the more realistic computer simulation macro-models available, providing a high degree of realism with respect to characteristics of the actual amplifier. This model, shown in Listing 1, is based on typical values for the device and can be downloaded from Analog Devices’ Internet site at www.analog.com. The model uses a common source output stage to provide railto-rail performance. This allows realistic simulation of openloop gain dependency on load resistance as well as maximum output voltage versus output current. Two differential pairs are used in the input stage of the model, simulating the rail-to-rail input stage of the AD8591/AD8592/AD8594 amplifier. The EOS voltage source establishes the input offset voltage and is also used to simulate the common-mode rejection power supply rejection, and input voltage noise characteristics for the model. In addition, G2, R2 and CF are used to help set the open-loop gain and gain-bandwidth product of the model. A number of secondary characteristics are also accurately portrayed in the SPICE model. Flicker noise is accurately modeled with the 1/f corner frequency set through the KF and AF terms in the input stage transistors. C1 and C2 are used in the input section to create secondary poles to achieve an accurate phase margin characteristic for the model. The AD8591/AD8592/AD8594 shutdown circuitry is included in the model. Switches S1 through S7 deactivate the op amp circuitry in shutdown mode. The logic threshold for the shutdown circuitry is accurately modeled through the VSWITCH model parameters near the end of the listing. The active supply current versus supply voltage is also modeled through the voltage-controlled current source GSY. Characteristics of this model are based on typical values for the AD8591/AD8592/AD8594 amplifier at +27°C. The model’s characteristics are optimized specifically at +27°C, and may lose accuracy at different simulation temperatures. –12– REV. A AD8591/AD8592/AD8594 Listing 1: AD859x SPICE Macro-Model * AD8592 SPICE Macro-Model Typical Values * 9/98, Ver. 1 * TAM / ADSC * * Copyright 1998 by Analog Devices * * Refer to “README.DOC” file for License * Statement. Use of this * model indicates your acceptance of the * terms and provisions in * the License Statement. * * Node Assignments * noninverting input * | inverting input * | | positive supply * | | | negative supply * | | | | output * | | | | | shutdown * | | | | | | .SUBCKT AD8592 1 2 99 50 45 80 * * INPUT STAGE * M1 4 1 3 3 PIX L=0.8E-6 W=125E-6 M2 6 7 3 3 PIX L=0.8E-6 W=125E-6 RC1 4 50 4E3 RC2 6 50 4E3 C1 4 6 2E-12 I1 99 8 100E-6 M3 M4 RC3 RC4 C2 I2 10 11 10 11 10 13 1 7 99 99 11 50 12 12 NIX L=0.8E-6 W=125E-6 12 12 NIX L=0.8E-6 W=125E-6 4E3 4E3 2E-12 100E-6 EOS 7 2 POLY(3) (21,98) (73,98) (61,0) +1E-3 1 1 1 IOS 1 2 2.5E-12 V1 99 9 0.9 D1 3 9 DX V2 14 50 0.9 D2 14 12 DX S1 3 8 (82,98) SOPEN S2 99 8 (98,82) SCLOSE S3 12 13 (82,98) SOPEN S4 13 50 (98,82) SCLOSE * * CMRR=64dB, ZERO AT 20kHz * ECM1 20 98 POLY(2) (1,98) (2,98) 0 .5 .5 RCM1 20 21 79.6E3 CCM1 20 21 100E-12 RCM2 21 98 50 * * PSRR=80dB, ZERO AT 200Hz * RPS1 70 0 1E6 RPS2 71 0 1E6 CPS1 99 70 1E-5 REV. A –13– AD8591/AD8592/AD8594 CPS2 50 71 1E-5 EPSY 98 72 POLY(2) (70,0) (0,71) 0 1 1 RPS3 72 73 1.59E6 CPS3 72 73 500E-12 RPS4 73 98 80 * * INTERNAL VOLTAGE REFERENCE * EREF 98 0 POLY(2) (99,0) (50,0) 0 .5 .5 GSY 99 50 POLY(1) (99,50) 20E-6 10E-7 * * SHUTDOWN SECTION * E1 81 98 (80,50) 1 R1 81 82 1E3 C3 82 98 1E-9 * * VOLTAGE NOISE REFERENCE OF 30nV/rt(Hz) * VN1 60 0 0 RN1 60 0 16.45E-3 HN 61 0 VN1 30 RN2 61 0 1 * * GAIN STAGE * G2 98 30 POLY(2) (4,6) (10,11) 0 2.19E-5 +2.19E-5 R2 30 98 13E6 CF 45 30 5E-12 S5 30 98 (98,82) SCLOSE D3 30 31 DX D4 32 30 DX V3 99 31 0.6 V4 32 50 0.6 * * OUTPUT STAGE * M5 45 46 99 99 POX L=0.8E-6 W=16E-3 M6 45 47 50 50 NOX L=0.8E-6 W=16E-3 EG1 99 48 POLY(1) (98,30) 1.06 1 EG2 49 50 POLY(1) (30,98) 1.05 1 RG1 48 46 10E3 RG2 49 47 10E3 S6 46 99 (98,82) SCLOSE S7 47 50 (98,82) SCLOSE * * MODELS * .MODEL PIX PMOS (LEVEL=2,KP=20E-6,VTO=-0.7, LAMBDA=0.01,AF=1,KF=1E-31) .MODEL NIX NMOS (LEVEL=2,KP=20E-6,VTO=0.7, LAMBDA=0.01,AF=1,KF=1E-31) .MODEL POX PMOS (LEVEL=2,KP=8E-6,VTO=-1, LAMBDA=0.067) .MODEL NOX NMOS (LEVEL=2,KP=13.4E-6,VTO=1, LAMBDA=0.067) .MODEL SOPEN VSWITCH(VON=2.4,VOFF=0.8, RON=10,ROFF=1E9) .MODEL SCLOSE VSWITCH(VON=-0.8,VOFF=-2.4, RON=10,ROFF=1E9) .MODEL DX D(IS=1E-14) .ENDS AD8592 –14– REV. A AD8591/AD8592/AD8594 OUTLINE DIMENSIONS Dimensions shown in inches and (mm). 0.124 (3.15) 0.112 (2.84) 0.122 (3.10) 0.106 (2.70) 6 0.071 (1.80) 0.059 (1.50) 5 1 10 4 2 C3456a–0–2/99 10-Lead SOIC (RM-10) 6-Lead SOT (RT-6) 0.118 (3.00) 0.098 (2.50) 3 6 0.124 (3.15) 0.112 (2.84) 0.199 (5.05) 0.187 (4.75) 1 5 PIN 1 0.037 (0.95) BSC PIN 1 0.0197 (0.50) BSC 0.075 (1.90) BSC 0.051 (1.30) 0.035 (0.90) 0.057 (1.45) 0.035 (0.90) 0.020 (0.50) SEATING 0.010 (0.25) PLANE 0.059 (0.15) 0.000 (0.00) 108 0.009 (0.23) 08 0.003 (0.08) 0.038 (0.97) 0.030 (0.76) 0.022 (0.55) 0.014 (0.35) 0.122 (3.10) 0.110 (2.79) 0.043 (1.09) 0.037 (0.94) 0.006 (0.15) 0.002 (0.05) 16-Lead Thin Shrink Small Outline (RU-16) 0.016 (0.41) 0.006 (0.15) 0.1574 (4.00) 0.1497 (3.80) 1 0.256 (6.50) 0.246 (6.25) 0.177 (4.50) 0.169 (4.30) 9 PIN 1 PIN 1 0.0118 (0.30) 0.0075 (0.19) 0.0079 (0.20) 0.0035 (0.090) 0.0500 SEATING (1.27) PLANE BSC 88 08 0.2440 (6.20) 0.2284 (5.80) 0.0688 (1.75) 0.0532 (1.35) 0.0192 (0.49) 0.0138 (0.35) 0.0099 (0.25) 0.0075 (0.19) 0.0196 (0.50) x 45° 0.0099 (0.25) 8° 0° 0.0500 (1.27) 0.0160 (0.41) 0.028 (0.70) 0.020 (0.50) PRINTED IN U.S.A. 0.0256 (0.65) BSC 0.0433 (1.10) MAX 9 8 0.0098 (0.25) 0.0040 (0.10) 8 0.006 (0.15) 0.002 (0.05) SEATING PLANE 0.022 (0.56) 0.021 (0.53) 0.3937 (10.00) 0.3859 (9.80) 16 1 68 SEATING 08 0.011 (0.28) PLANE 0.003 (0.08) 16-Lead Narrow Body SO (R-16A) 0.201 (5.10) 0.193 (4.90) 16 0.120 (3.05) 0.112 (2.84) REV. A –15–