AD ADP2114

Configurable, Dual 2 A/Single 4 A,
Synchronous Step-Down DC-to-DC Regulator
ADP2114
FEATURES
TYPICAL APPLICATION CIRCUIT
VIN = 5V
10Ω
1µF
22µF
100kΩ
EN2
VIN4
EN1
VIN1
VDD
100kΩ
VIN6
PGOOD2
PGOOD2
VOUT2 = 1.8V, 2A
2.2µH
SW3
VIN3
PGOOD1
ADP2114
SW4
22µF
15kΩ
SW1
VOUT1 = 3.3V, 2A
SW2
47µF
PGND2
PGND4
SYNC
PGOOD1
4.7µH
PGND1
PGND3
47µF
22µF
VIN2
VIN5
FB1
FB2
V2SET
47kΩ
V1SET
SYNC/CLKOUT
22kΩ
1.2nF
10nF
COMP2
SS2
COMP1
SS1
FREQ
OPCFG
SCFG
GND
22kΩ
10nF
1.2nF
8.2kΩ
08143-001
Configurable 2 A/2 A or 3 A/1 A dual output load
combinations or 4 A combined single output
High efficiency: up to 95%
Input voltage VIN: 2.75 V to 5.5 V
Selectable fixed output: 0.8 V, 1.2 V, 1.5 V, 1.8 V, 2.5 V, 3.3 V or
adjustable output voltage to 0.6 V minimum
±1.5% accurate reference voltage
Selectable switching frequency: 300 kHz, 600 kHz, 1.2 MHz
or synchronized from 200 kHz to 2 MHz
Optimized gate slew rate for reduced EMI
External synchronization input or internal clock output
Dual-phase, 180° phase shifted PWM channels
Current mode for fast transient response
Pulse skip under light load or forced PWM operation
Input undervoltage lockout (UVLO)
Independent enable inputs and PGOOD outputs
Overcurrent and thermal overload protection
Externally programmable soft start
32-lead 5 mm × 5 mm LFCSP package
fSW = 600kHz
Figure 1.
APPLICATIONS
The ADP2114 is a versatile, synchronous step-down, switching
regulator that satisfies a wide range of customer point-of-load
requirements. The two PWM channels can be configured to
deliver independent outputs at 2 A and 2 A (or 3 A/1 A) or can be
configured as a single interleaved output capable of delivering 4 A.
The two PWM channels are 180º phase shifted to reduce input
ripple current and to reduce input capacitance.
The ADP2114 provides high efficiency and operates at switching
frequencies of up to 2 MHz. At light loads, the ADP2114 can be
set to operate in pulse skip mode for higher efficiency or in forced
PWM mode to reduce EMI.
The ADP2114 is designed with an optimized gate slew rate to reduce
EMI emissions, allowing it to power sensitive, high performance
signal chain circuits. The switching frequency can be set to 300 kHz,
600 kHz, or 1.2 MHz and can be synchronized to an external clock
that minimizes the system noise. The bidirectional synchronization
pin is also configurable as a 90° out-of-phase output clock, providing
the possibility for a stackable multiphase power solution.
100
VIN = 3.3V; VOUT = 1.8V
VIN = 5.0V; VOUT = 3.3V
95
90
85
80
VIN = 5.0V; VOUT = 1.8V
75
70
0.01
0.1
1
3
LOAD CURRENT (A)
08143-002
GENERAL DESCRIPTION
The ADP2114 input voltage range is from 2.75 V to 5.5 V, and it
converts to fixed outputs of 0.8 V, 1.2 V, 1.5 V, 1.8 V, 2.5 V, or
3.3 V that can be set independently for each channel using
external resistors. Using a resistor divider, it is also possible to
set the output voltage as low as 0.6 V. The ADP2114 operates
over the −40°C to +125°C junction temperature range.
EFFICIENCY (%)
Point of load regulation
Telecommunications and networking systems
Consumer electronics
Industrial and Instrumentation
Medical
Figure 2. Typical Efficiency vs. Load Current
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2009 Analog Devices, Inc. All rights reserved.
ADP2114
TABLE OF CONTENTS
Features .............................................................................................. 1 Maximum Duty Cycle Operation ............................................ 23 Applications ....................................................................................... 1 Synchronization .......................................................................... 23 General Description ......................................................................... 1 Converter Configuration ............................................................... 24 Typical Application Circuit ............................................................. 1 Selecting the Output Voltage .................................................... 24 Revision History ............................................................................... 2 Setting the Oscillator Frequency .............................................. 25 Specifications..................................................................................... 3 Synchronization and CLKOUT ................................................ 25 Absolute Maximum Ratings............................................................ 5 Operation Mode Configuration ............................................... 26 ESD Caution .................................................................................. 5 External Components Selection ................................................... 27 Pin Configuration and Function Descriptions ............................. 6 Input Capacitor Selection .......................................................... 27 Typical Performance Characteristics ............................................. 8 VDD RC Filter ............................................................................ 27 Supply Current ............................................................................ 13 Inductor Selection ...................................................................... 27 Load Transient Response........................................................... 14 Output Capacitor Selection....................................................... 28 Bode Plots .................................................................................... 19 Control Loop Compensation .................................................... 28 Simplified Block Diagram ............................................................. 20 Design Example .............................................................................. 30 Theory of Operation ...................................................................... 21 Channel 1 Configuration and Components Selection .......... 30 Control Architecture .................................................................. 21 Channel 2 Configuration and Components Selection .......... 31 Undervoltage Lockout (UVLO) ............................................... 21 System Configuration ................................................................ 32 Enable/Disable Control ............................................................. 21 Application Circuits ....................................................................... 33 Soft Start ...................................................................................... 21 Power Dissipation, Thermal Considerations .............................. 35 Power Good................................................................................. 22 Circuit Board Layout Recommendations ................................... 36 Pulse Skip Mode ......................................................................... 22 Outline Dimensions ....................................................................... 37 Hiccup Mode Current Limit ..................................................... 23 Ordering Guide .......................................................................... 37 Thermal Overload Protection................................................... 23 REVISION HISTORY
7/09—Revision 0: Initial Version
Rev. 0 | Page 2 of 40
ADP2114
SPECIFICATIONS
If unspecified, VDD = VINx = EN1 = EN2 = 5.0 V. The minimum and maximum specifications are valid for TJ = −40°C to +125°C, unless
otherwise specified. Typical values are at TJ = 25°C. All limits at temperature extremes are guaranteed via correlation using standard
statistical quality control (SQC).
Table 1.
Parameter
POWER SUPPLY
VDD Bias Voltage
Undervoltage Lockout Threshold
Undervoltage Lockout Hysteresis
Quiescent Current
Symbol
VDD
UVLO
IDDCh1
IDDCh2
IDDCh1 + Ch2
Shutdown Current
ERROR INTEGRATOR (OTA)
FB1, FB2 Input Bias Current
Transconductance
COMPx VOLTAGE RANGE
COMPx Zero-Current Threshold
COMPx Clamp High Voltage
COMPx Clamp Low Voltage
OUTPUT CHARACTERISTICS
Output Voltage Accuracy
IDDSD
IFB
Conditions
Min
2.75
VDD rising
VDD falling
2.35
EN1 = VDD = 5 V, EN2 = GND, VFB1 = VDD,
OPCFG = GND
EN2 = VDD = 5V, EN1 = GND, VFB2 = VDD,
OPCFG = GND
EN1 = EN2 = VDD = 5 V, VFB2 = VFB1 = VDD,
OPCFG = GND
EN1 = EN2 = GND, VDD = VINx = 2.75 V to 5.5 V,
TJ = −40°C to +115°C
Adjustable output, VFBx = 0.6 V,
V1SET, V2SET = VDD or via 82 kΩ to GND
Fixed output; VFBx = 1.2 V,
V1SET, V2SET via 4.7 kΩ to GND
gM
Guaranteed by design
VDD = VINx = 2.75 V to 5.5 V
VDD = VINx = 2.75 V to 5.5 V
VFB
Adjustable output, TJ = 25°C,
V1SET, V2SET = VDD or via 82 kΩ to GND
Adjustable output, TJ = −40°C to +125°C,
V1SET, V2SET = VDD or via 82 kΩ to GND
Fixed output, TJ = 25°C, V1SET, V2SET = GND
or via 4.7 kΩ, 8.2 kΩ, 15 kΩ, 27 kΩ,
47 kΩ to GND
Fixed output, TJ = −40°C to +125°C,
V1SET, V2SET = GND or via 4.7 kΩ, 8.2 kΩ,
15 kΩ, 27 kΩ, 47 kΩ to GND
VDD = VINx = 2.75 V to 5.5 V
VDD = VINx = 2.75 V to 5.5 V
All oscillator parameters provided for
VDD = 2.75 V to 5.5 V
FREQ tied to GND
FREQ via 8.2 kΩ to GND
FREQ via 27 kΩ to GND
fSYNC = 2 × fSW
FREQ tied to GND
FREQ via 8.2 kΩ to GND
FREQ via 27 kΩ to GND
Line Regulation
Load Regulation
OSCILLATOR
Switching Frequency
fSW
SYNC Frequency Range
fSYNC
Max
Unit
2.65
2.47
0.18
1.7
5.5
2.75
V
V
2.5
V
mA
1.7
2.5
mA
3.0
4.0
mA
1.0
10
μA
1
65
nA
11
15
μA
550
VCOMP, ZCT
VCOMP, HI
VCOMP, LO
VFB ERROR
Typ
SYNC Input Pulse Width
Rev. 0 | Page 3 of 40
μA/V
2.45
0.65
1.12
2.36
0.70
V
V
V
0.597
0.600
0.603
V
0.594
0.600
0.606
V
−1.0
+1.0
%
−1.5
+1.5
%
0.05
0.03
255
510
1020
400
800
1600
100
300
600
1200
%/V
%/A
345
690
1380
kHz
kHz
kHz
1000
2000
4000
kHz
kHz
kHz
ns
ADP2114
Parameter
SYNC Pin Capacitance to GND
SYNC Input Logic Low
SYNC Input Logic High
Phase Shift Between Channels
CLKOUT Frequency
CLKOUT Positive Pulse Time
CLKOUT Rise or Fall Time
CURRENT LIMIT
Symbol
CSYNC
VIL_SYNC
VIH_SYNC
Conditions
fCLKOUT
fCLKOUT = 2 × fSW
FREQ tied to GND
FREQ via 8.2 kΩ to GND
FREQ via 27 kΩ to GND
Peak Output Current Limit, Channel 2
ILIMIT2
SWON MIN
SWOFF MIN
SWx Maximum Leakage Current
THERMAL SHUTDOWN
Thermal Shutdown Threshold
Thermal Shutdown Hysteresis
SOFT START
SS1, SS2 Pin Current
Soft Start Threshold Voltage
Soft Start Pull-Down Current
POWER GOOD
Overvoltage PGOODx Rising Threshold 2
Overvoltage PGOODx Falling Threshold2
Undervoltage PGOODx Rising Threshold2
Undervoltage PGOODx Falling Threshold2
PGOODx Delay
PGOODx Leakage Current
PGOODx Low Saturation Voltage
1
2
0.8
510
1020
2040
100
CCLKOUT = 20 pF
All current limit parameters provided for
VDD = VINx = 2.75 V to 5.5 V
OPCFG tied to GND or via 4.7 kΩ to GND
OPCFG via 8.2 kΩ or 15 kΩ to GND
OPCFG tied to GND or via 4.7 kΩ to GND
OPCFG via 8.2 kΩ or 15 kΩ to GND
2.4
3.5
2.4
1.2
fSW = 300 kHz
10
ENLOW
ENHI
IEN_LEAK
VDD = VINx = 3.3 V
VDD = VINx = 5.0 V
VDD = VINx = 3.3 V
VDD = VINx = 5.0 V
VDD = VINx = 2.75 V to 5.5 V
VDD = VINx = 5.5 V
VDD = VINx = 2.75 V
VDD = VINx = 2.75 V to 5.5 V; ENx = GND,
TJ = −40°C to +115°C
VDD = VINx = 2.75 V to 5.5 V
VDD = VINx = 2.75 V to 5.5 V
VDD = VINx = ENx = 2.75 V to 5.5 V,
TJ = −40°C to +115°C
3.3
4.5
3.3
1.9
4
13.6
8
68
52
32
27
107
192
255
0.1
kHz
kHz
kHz
ns
ns
4.0
5.3
4.0
2.6
A
A
A
A
A/V
ms
Cycles
17
15
0.8
0.1
1
4.8
Pin-to-pin measurements.
The thresholds are expressed in percentage terms of the nominal output voltage.
Rev. 0 | Page 4 of 40
7.8
0.5
100
85
VPGOODx = VDD
IPGOODx = 1 mA
6.0
0.65
116
108
92
84
50
0.1
50
mΩ
mΩ
mΩ
mΩ
ns
ns
ns
μA
V
V
μA
°C
°C
150
25
VDD = VINx = 2.75 V to 5.5 V; VSS = 0 V
VDD = VINx = 2.75 V to 5.5 V
VDD = VINx = 2.75 V to 5.5 V; EN = GND
All power good parameters provided for
VDD = VINx = 2.75 V to 5.5 V
Unit
pF
V
V
Degrees
690
1380
2760
2
TTMSD
ISS1, ISS2
VSS_THRESH
600
1200
2400
10
GCS
Low-Side, N-Channel RDS ON1
ENABLE INPUT
EN1, EN2 Logic Low Level
EN1, EN2 Logic High Level
EN1, EN2 Input Leakage Current
Max
2.0
tCLKOUT
ILIMIT1
SWx Minimum On Time
SWx Minimum Off Time
Typ
5
180
Peak Output Current Limit, Channel 1
Current Sense Amplifier Gain
Hiccup Time
Number of Cumulative Current Limit
Cycles to Go into Hiccup
SWITCH NODE CHARACTERISTICS
High-Side, P-Channel RDS ON 1
Min
114
97
1
110
μA
V
mA
%
%
%
%
μs
μA
mV
ADP2114
ABSOLUTE MAXIMUM RATINGS
Table 2.
Parameter
VDD to GND
VIN1, VIN2, VIN3, VIN4, VIN5, VIN6 to
PGND1, PGND2, PGND3, PGND4
EN1, EN2, SCFG, FREQ, FB1, FB2, SYNC/
CLKOUT, PGOOD1, PGOOD2, V1SET,
V2SET, COMP1, COMP2, SS1, SS2 to GND
FB1, FB2 to GND
SW1, SW2, SW3, SW4 to PGND1, PGND2,
PGND3, PGND4
PGND1, PGND2, PGND3, PGND4 to GND
VIN1, VIN2, VIN3, VIN4, VIN5, VIN6 to VDD
θJA, JEDEC 1S2P PCB, Natural Convection
Operating Junction Temperature Range
Storage Temperature Range
Maximum Soldering Lead
Temperature (10 sec)
Rating
−0.3 V to +6 V
−0.3 V to +6 V
−0.3 V to (VDD + 0.3 V)
−0.3V to +3.6V
−0.3 V to (VDD + 0.3 V)
±0.3 V
±0.3 V
34°C/W
−40°C to +125°C
−65°C to +150°C
260°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Absolute maximum ratings apply individually only, not in
combination.
ESD CAUTION
Rev. 0 | Page 5 of 40
ADP2114
32
31
30
29
28
27
26
25
FB1
V1SET
SS1
PGOOD1
EN1
VIN1
VIN2
VIN3
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
1
2
3
4
5
6
7
8
ADP2114
TOP VIEW
(Not to Scale)
THERMAL PAD
24
23
22
21
20
19
18
17
SW1
SW2
PGND1
PGND2
PGND3
PGND4
SW3
SW4
NOTES
1. CONNECT THE EXPOSED THERMAL PAD TO THE
SIGNAL/ANALOG GROUND PLANE.
08143-003
FB2
V2SET
SS2
PGOOD2
EN2
VIN4
VIN5
VIN6
9
10
11
12
13
14
15
16
GND
COMP1
FREQ
SCFG
SYNC/CLKOUT
OPCFG
COMP2
VDD
Figure 3. Pin Configuration
Table 3. Pin Function Descriptions
Pin No.
1
Mnemonic
GND
2
COMP1
3
FREQ
4
SCFG
5
SYNC/CLKOUT
6
OPCFG
7
COMP2
8
VDD
9
FB2
10
V2SET
11
SS2
12
PGOOD2
13
EN2
Description
Ground for the Internal Analog and Digital Circuits. Connect GND to the signal/analog ground plane before
connecting to the power ground.
Error Amplifier Output for Channel 1. Connect a series RC network from COMP1 to GND to compensate for
Channel 1. For multiphase operation, tie COMP1 and COMP2 together.
Frequency Select Input. Connect this pin through a resistor to GND to set the appropriate switching frequency
(see Table 5).
Synchronization Configuration Input. SCFG configures the SYNC/CLKOUT pin as an input or output. Tie this pin
to VDD to configure SYNC/CLKOUT as an output. Tie this pin to GND to configure SYNC/CLKOUT as an input.
This is a configurable bidirectional pin (configured with the SCFG pin—see the Pin 4 description for details).
When SYNC/CLKOUT is an output, a buffered clock of twice the switching frequency with a phase shift of 90°
is available on this pin. When configured as an input, this pin accepts an external clock to which the converters
are synchronized. The frequency select resistor, mentioned in the description of Pin 3, must be selected close to
the expected switching frequency for stable operation.
Operation Configuration Input. Connect this pin through a resistor to GND to set the system mode of operation
according to Table 7. This pin can be used to select a peak current limit for each power channel and enable or
disable the pulse skip mode.
Error Amplifier Output for Channel 2. Connect a series RC network from COMP2 to GND to compensate the
Channel 2. Tie COMP1 and COMP2 together for multiphase configuration.
Power Supply Input. The power source for the ADP2114 internal circuitry. Connect VDD and VINx with a
10 Ω resistor as close as possible to the ADP2114. Bypass VDD to GND with a 1 μF or greater capacitor.
Feedback Voltage Input for Channel 2. For the fixed output voltage option, connect FB2 to VOUT2. For the
adjustable output voltage option, connect this pin to a resistor divider between VOUT2 and GND. The reference
voltage for the adjustable output voltage option is 0.6 V. With multiphase configurations, connect FB2 to FB1
and then connect them to VOUT.
Output Voltage Set Pin for Channel 2. Connect this pin through a resistor to GND or tie to VDD to select a fixed
output voltage option (0.8 V, 1.2 V, 1.5 V, 1.8 V, 2.5 V, or 3.3 V) or an adjust output voltage for VOUT2. See Table 4
for output voltage selection.
Soft Start Input for Channel 2. Place a capacitor from SS2 to GND to set the soft start period. A 10 nF capacitor
sets a 1 ms soft start period. For multiphase configuration, connect SS2 to SS1.
Open-Drain Power Good Output for Channel 2. Place a 100 kΩ pull-up resistor to VDD or any other voltage ≤ 5.5 V;
PGOOD2 pulls low when Channel 2 is out of regulation.
Enable Input for Channel 2. Drive EN2 high to turn on the Channel 2 converter and drive EN2 low to turn off
Channel 2. Tie EN2 to VDD for startup with VDD. With multiphase configuration, tie EN2 to EN1.
Rev. 0 | Page 6 of 40
ADP2114
Pin No.
14
15
16
17
Mnemonic
VIN4
VIN5
VIN6
SW4
18
SW3
19
20
21
22
23
PGND4
PGND3
PGND2
PGND1
SW2
24
SW1
25
26
27
28
VIN3
VIN2
VIN1
EN1
29
PGOOD1
30
SS1
31
V1SET
32
FB1
EPAD (EP)
Description
Power Supply Input. The source of the high-side internal power MOSFET of Channel 2.
Power Supply Input. The source of the high-side internal power MOSFET of Channel 2.
Power Supply Input. The source of the high-side internal power MOSFET of Channel 2.
Switch Node Output. The drain of the P-channel power switch and N-channel synchronous rectifier of Channel 2.
Tie SW3 to SW4 and then connect the output LC filter between SW and the output voltage.
Switch Node Output. The drain of the P-channel power switch and N-channel synchronous rectifier of Channel 2.
Tie SW3 to SW4 and then connect the output LC filter between SW and the output voltage.
Power Ground. Source of the low-side internal power MOSFET of Channel 2.
Power Ground. Source of the low-side internal power MOSFET of Channel 2.
Power Ground. Source of the low-side internal power MOSFET of Channel 1.
Power Ground. Source of the low-side internal power MOSFET of Channel 1.
Switch Node Output. The drain of the P-channel power switch and N-channel synchronous rectifier of Channel 1.
Tie SW1 to SW2 and connect the output LC filter between SW and the output voltage.
Switch Node Output. The drain of the P-channel power switch and N-channel synchronous rectifier of Channel 1.
Tie SW1 to SW2 and connect the output LC filter between SW and the output voltage.
Power Supply Input. The source of the high-side internal power MOSFET of Channel 1.
Power Supply Input. The source of the high-side internal power MOSFET of Channel 1.
Power Supply Input. The source of the high-side internal power MOSFET of Channel 1.
Enable Input for Channel 1. Drive EN1 high to turn on the Channel 1 converter and drive EN1 low to turn off
Channel 1. Tie EN1 to VDD for startup with VDD. With multiphase configurations, connect EN1 to EN2.
Open-Drain Power Good Output for Channel 1. Place a 100 kΩ pull-up resistor to VDD or any other voltage ≤ 5.5 V;
PGOOD1 pulls low when Channel 1 is out of regulation.
Soft Start Input for Channel 1. Place a capacitor from SS1 to GND to set the soft start period. A 10 nF capacitor
sets a 1 ms soft start period. For multiphase configuration, connect SS1 to SS2.
Output Voltage Set Pin for Channel 1. Connect this pin through a resistor to GND or tie to VDD to select a fixed
output voltage option (0.8 V, 1.2 V, 1.5 V, 1.8 V, 2.5 V, or 3.3 V) or an adjustable output voltage for VOUT1. See Table 4
for output voltage selection.
Feedback Voltage Input for Channel 1. For the fixed output voltage option, connect FB1 to VOUT1. For the
adjusted output voltage option, connect this pin to a resistor divider between VOUT1 and GND. With multiphase
configurations, connect FB1 to FB2 and then connect them to VOUT.
Exposed Thermal Pad. Connect to the signal/analog ground plane.
Rev. 0 | Page 7 of 40
ADP2114
100
95
95
90
90
85
80
75
70
100
1k
65
10k
LOAD CURRENT (mA)
60
10
1k
10k
Figure 6. Efficiency vs. Load at fSW = 1.2 MHz;
Inductor TOKO FDV0620-1R0M, 1.0 μH, 14 mΩ
100
90
95
85
VIN = 3.3V
EFFICIENCY (%)
90
85
80
75
70
VOUT = 3.3V
VOUT = 3.3V; PULSE SKIP
VOUT = 1.8V
VOUT = 1.8V; PULSE SKIP
65
100
1k
80
VIN = 5V
75
70
65
10k
LOAD CURRENT (mA)
08143-005
EFFICIENCY (%)
100
LOAD CURRENT (mA)
Figure 4. Channel 1 Efficiency vs. Load, VIN = 5 V and fsw = 300 kHz;
VOUT = 3.3 V, Inductor Cooper Bussmann DR1050-8R2-R, 8.2 μH, 15 mΩ;
VOUT = 1.8 V, Inductor TOKO FDV0620-4R7M, 4.7 μH, 53 mΩ
60
10
VIN = 5V,
VOUT = 2.5V FORCED PWM
VIN = 5V,
VOUT = 2.5V PULSE SKIP
VIN = 3.3V,
VOUT = 1.2V FORCED PWM
VIN = 3.3V,
VOUT = 1.2V PULSE SKIP
75
60
100
1k
10k
LOAD CURRENT (mA)
Figure 7. Efficiency Combined Dual-Phase Output, VOUT = 0.8 V and
fSW = 1.2 MHz; Inductor TOKO FDV0620-1R0M, 1.0 μH, 14 mΩ
Figure 5. Channel 2 Efficiency vs. Load, VIN = 5 V and fSW = 600 kHz;
VOUT = 3.3 V, Inductor TOKO FDV0620-4R7M, 4.7 μH, 53 mΩ;
VOUT = 1.8 V, Inductor TOKO FDV0620-2R2M, 2.2 μH, 30 mΩ
Rev. 0 | Page 8 of 40
08143-007
60
10
80
70
VOUT = 3.3V
VOUT = 3.3V; PULSE SKIP
VOUT = 1.8V
VOUT = 1.8V; PULSE SKIP
65
85
08143-006
EFFICIENCY (%)
100
08143-004
EFFICIENCY (%)
TYPICAL PERFORMANCE CHARACTERISTICS
ADP2114
0.25
0
–0.25
500
1000
1500
2000
2500
3000
LOAD CURRENT (mA)
–0.50
0.5
0.4
0.4
0.3
0.3
0.1
0
–0.1
–0.2
–0.3
–0.4
3.0
3.5
4.0
4.5
5.0
5.5
VIN (V)
1500
2000
0.2
0.1
0
–0.1
–0.2
–0.3
–0.5
2.5
0.75
0.75
0.50
0.50
VOUT ERROR (%)
1.00
VIN = 5.5V, NO LOAD
0
–0.25
VIN = 2.75V; 3A LOAD
75
100
TEMPERATURE (°C)
125
5.5
Figure 10. Output Voltage vs. Temperature,
Channel 1: VOUT = 0.6 V and fSW = 600 kHz
VIN = 2.75V; 2A LOAD
–0.25
–0.75
50
5.0
VIN = 5.5V, NO LOAD
–0.75
25
4.5
0
–0.50
0
4.0
0.25
–0.50
–25
3.5
Figure 12. Line Regulation, Channel 2: Load Current = 1 A and fSW = 600 kHz
1.00
0.25
3.0
VIN (V)
08143-010
VOUT ERROR (%)
Figure 9. Line Regulation, Channel 1: Load Current = 3 A and fSW = 600 kHz
–1.00
–50
1000
–0.4
08143-009
–0.5
2.5
500
Figure 11. Load Regulation, Channel 2: VIN = 5 V, fSW = 300 kHz, and TA = 25°C
0.5
0.2
0
LOAD CURRENT (mA)
VOUT ERROR, NORMALIZED (%)
VOUT ERROR, NORMALIZED (%)
Figure 8. Load Regulation, Channel 1: VIN = 5 V, fSW = 600 kHz, and TA = 25°C
–0.25
08143-012
0
0
–1.00
–50
–25
0
25
50
75
100
TEMPERATURE (°C)
Figure 13. Output Voltage vs. Temperature,
Channel 2: VOUT = 1.5 V and fSW = 600 kHz
Rev. 0 | Page 9 of 40
125
08143-013
–0.50
0.25
08143-011
VOUT ERROR, NORMALIZED (%)
0.50
08143-008
VOUT ERROR, NORMALIZED (%)
0.50
ADP2114
250
225
330
fSW = 300kHz
fSW = 600kHz
320
310
175
fSW (kHz)
150
125
290
100
280
75
3.0
3.5
4.0
4.5
5.0
5.5
VIN (V)
270
2.5
08143-014
50
2.5
350
fSW = 600kHz
310
fSW = 1.2MHz
3.5
4.0
4.5
5.0
5.5
Figure 17. Switching Frequency vs. Input Voltage, fSW = 300 kHz
660
fSW = 300kHz
330
3.0
VIN (V)
Figure 14. Minimum On-Time, Open Loop, Includes Dead Time
640
290
620
270
fSW (kHz)
MINIMUM OFF-TIME (ns)
300
08143-017
MINIMUM ON-TIME (ns)
fSW = 1.2MHz
200
250
230
600
580
210
190
560
3.0
3.5
4.0
4.5
5.0
5.5
VIN (V)
540
2.5
08143-015
150
2.5
3.0
3.5
4.0
4.5
5.0
5.5
VIN (V)
Figure 15. Minimum Off-Time, Open Loop, Includes Dead Time
08143-018
170
Figure 18. Switching Frequency vs. Input Voltage, fSW = 600 kHz
120
80
70
100
40
20
0
2.5
40
30
20
+125°C
+115°C
+85°C
+25°C
–40°C
3.0
50
10
3.5
4.0
VIN (V)
4.5
5.0
5.5
0
2.5
Figure 16. High-Side PMOS Resistance vs. Input Voltage, Includes Bond Wires
+125°C
+115°C
+85°C
+25°C
–40°C
3.0
3.5
4.0
VIN (V)
4.5
5.0
5.5
08143-019
NMOS RDS ON (mΩ)
60
08143-016
PMOS RDS ON (mΩ)
60
80
Figure 19. Low-Side NMOS Resistance vs. Input Voltage, Includes Bond Wires
Rev. 0 | Page 10 of 40
ADP2114
2.0
330
1.9
fSW (kHz)
310
ENABLE/DISABLE THRESHOLD (V)
320
VIN = 2.75V
300
VIN = 5.5V
290
280
1.8
1.7
1.6
ENABLE; VIN = 5.5V
1.5
ENABLE; VIN = 2.75V
1.4
DISABLE; VIN = 5.5V
DISABLE; VIN = 2.75V
1.3
1.2
1.1
1.0
0
25
50
75
100
125
TEMPERATURE (°C)
0.8
–50
08143-020
–25
UVLO THRESHOLD (V)
2.7
620
75
100
125
VIN = 2.75V
600
VIN = 5.5V
580
VDD RISING
2.6
2.5
VDD FALLING
560
0
25
50
75
100
125
TEMPERATURE (°C)
2.3
–50
08143-021
–25
1280
1260
1260
1240
1240
1220
1220
fSW (kHz)
1300
1280
1200
1180
1140
1120
1120
5.5
VIN (V)
08143-022
1140
5.0
75
100
125
VIN = 5.5 V
1180
1160
4.5
50
VIN = 2.75 V
1200
1160
4.0
25
Figure 24. UVLO Threshold vs. Temperature
1300
3.5
0
TEMPERATURE (°C)
Figure 21. Switching Frequency vs. Temperature, fSW = 600 kHz
3.0
–25
08143-024
2.4
1100
–50
–25
0
25
50
75
100
125
TEMPERATURE (°C)
Figure 25. Switching Frequency vs. Temperature, fSW = 1.2 MHz
Figure 22. Switching Frequency vs. Input Voltage, fSW = 1.2 MHz
Rev. 0 | Page 11 of 40
08143-025
fSW (kHz)
50
2.8
640
fSW (kHz)
25
Figure 23. Enable/Disable Threshold vs. Temperature
660
1100
2.5
0
TEMPERATURE (°C)
Figure 20. Switching Frequency vs. Temperature, fSW = 300 kHz
540
–50
–25
08143-023
0.9
270
–50
ADP2114
120
6.0
OVERVOLTAGE; VOUT RISING
5.5
5.0
110
CURRENT LIMIT (A)
105
100
95
UNDERVOLTAGE; VOUT RISING
90
4.0
2A OPTION
3.5
3.0
2.5
1A OPTION
2.0
1.5
UNDERVOLTAGE, VOUT FALLING
85
1.0
0.5
–25
0
25
50
75
100
125
TEMPERATURE (°C)
0
–50
–25
0
25
50
75
100
125
TEMPERATURE (°C)
Figure 26. PGOOD Threshold vs. Temperature
08143-029
80
–50
3A OPTION
4.5
OVERVOLTAGE; VOUT FALLING
08143-026
PGOOD THRESHOLD (%)
115
Figure 29. Peak Current Limit vs. Temperature, VIN = 5 V
700
10
9
650
600
7
VIN = 5.5V
6
gm (µA/V)
5
4
VIN = 5.5V
3
VIN = 2.75V
500
450
400
2
VIN = 2.75V
350
0
–50
–25
0
25
50
75
100
125
TEMPERATURE (°C)
08143-027
1
Figure 27. Shutdown Current vs. Temperature
4
3
VIN = 5.5V
2
VIN = 2.75V
–25
0
25
50
75
100
125
TEMPERATURE (°C)
08143-028
1
0
–50
300
–50
–25
0
25
50
75
TEMPERATURE (°C)
Figure 30. gM vs. Temperature
5
VDD CURRENT (mA)
550
Figure 28. VDD Input Current vs. Temperature (Not Switching)
Rev. 0 | Page 12 of 40
100
125
08143-030
SHUTDOWN CURRENT (µA)
8
ADP2114
SUPPLY CURRENT
5.0
5.0
4.5
4.5
4.0
4.0
VDD CURRENT (mA)
3.5
3.0
2.5
FORCED PWM
2.0
3.0
2.5
PULSE SKIP
2.0
PULSE SKIP
3.0
3.5
4.0
4.5
5.0
5.5
VDD VOLTAGE (V)
1.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
VDD VOLTAGE (V)
Figure 31. VDD Supply Current, No Load,
Channel 1: VOUT = 1.5 V, Channel 2 Off, fSW = 1.2 MHz
08143-033
1.0
2.5
1.5
08143-031
1.5
Figure 33. VDD Supply Current, No Load,
Channel 1: VOUT = 1.5 V, Channel 2: VOUT = 0.8 V, fSW = 1.2 MHz
5.0
4.5
4.5
4.0
4.0
VDD CURRENT (mA)
5.0
3.5
3.0
FORCED PWM
2.5
2.0
VDD = 5.5V, FORCED PWM
VDD = 2.75V, FORCED PWM
3.5
3.0
VDD = 5.5V PULSE SKIP
2.5
VDD = 2.75V, PULSE SKIP
2.0
PULSE SKIP
1.5
1.5
1.0
2.5
3.0
3.5
4.0
4.5
5.0
VDD VOLTAGE (V)
5.5
08143-032
VDD CURRENT (mA)
3.5
1.0
–50
–25
0
25
50
75
100
125
TEMPERATURE (°C)
Figure 34. VDD Supply Current vs. Temperature,
Channel 1: VOUT = 1.5 V, Channel 2: VOUT = 0.8 V, fSW = 1.2 MHz
Figure 32. VDD Supply Current, No Load,
Channel 2: VOUT = 0.8 V, Channel 1 Off, fSW = 1.2 MHz
Rev. 0 | Page 13 of 40
08143-034
VDD CURRENT (mA)
FORCED PWM
ADP2114
LOAD TRANSIENT RESPONSE
VOUT
VOUT
2
2
IOUT
IOUT
4
4
SW
CH2 50mV
CH4 2.0A
M200µs 50MS/s
200ns/pt
A CH2
–33mV
CH3 5.0V
Figure 35. Channel 1: VIN = 5 V, VOUT = 3.3V, fSW = 600 kHz; Forced PWM
(See Table 12 for the Circuit Details)
CH2 50mV
CH4 1.0A
M200µs 50MS/s
20ns/pt
A CH2
–34mV
08143-038
3
CH1 5.0V
08143-035
1
SW
Figure 38. Channel 2: VIN = 5 V, VOUT = 1.8 V, fSW = 600 kHz; Pulse Skip
(See Table 12 for the Circuit Details)
VOUT
2
VOUT
2
IOUT
IOUT
4
SW
SW
4
CH2 50mV
CH4 2.0A
M200µs 50MS/s
200ns/pt
A CH2
–23mV
CH1 5.0V
Figure 36. Channel 2: VIN = 5 V, VOUT = 1.8 V, fSW = 600 kHz; Forced PWM
(See Table 12 for the Circuit Details)
CH2 10mV
CH4 2.0A
M200µs 12.5MS/s
80ns/pt
A CH4
960mA
08143-039
1
CH3 5.0V
08143-036
3
Figure 39. Channel 1: VIN = 3.3 V, VOUT = 1.2 V, fSW = 1.2 MHz; Forced PWM
(See Table 12 for the Circuit Details)
2
2
VOUT
VOUT
IOUT
IOUT
SW
4
SW
4
CH2 10mV
CH4 2.0A
M200µs 12.5MS/s A CH4
80ns/pt
960mA
CH1 5.0V
Figure 37. Channel 1: VIN = 5 V, VOUT = 1.2 V, fSW = 1.2 MHz; Forced PWM
(See Table 12 for the Circuit Details)
CH2 10mV
CH4 2.0A
M200µs 12.5MS/s
80ns/pt
A CH4
960mA
08143-040
1
CH1 5.0V
08143-037
1
Figure 40. Channel 1: VIN = 3.3 V, VOUT = 1.2 V, fSW = 1.2 MHz; Pulse Skip
(See Table 12 for the Circuit Details)
Rev. 0 | Page 14 of 40
ADP2114
2
VOUT
VOUT
2
VIN
VIN
CH1 5.0V
CH3 1.0V
CH2 10mV
M400µs
A CH3
4.86V
1
3
08143-041
1
3
CH1 5.0V
CH3 1.0V
Figure 41. 3.3 V to 5 V Line Transient, VOUT = 1.5 V, Load = 1 A
fSW = 1.2 MHz, Pulse Skip Enabled
CH2 10mV
M400µs
A CH3
3.50V
08143-044
SW
SW
Figure 44. 5 V to 3.3 V Line Transient, VOUT = 1.5 V, Load = 1 A
fSW = 1.2 MHz, Forced PWM
2
VOUT
VOUT
2
VIN
VIN
SW
SW
CH2 10mV
M400µs
A CH3
3.58V
3
08143-042
CH1 5.0V
CH3 1.0V
CH1 2.0V
CH3 1.0V
Figure 42. 5 V to 3.3 V Line Transient, VOUT = 1.5 V, Load = 1 A
fSW = 1.2 MHz, Pulse Skip Enabled
CH2 10mV
M400µs
A CH3
4.82V
08143-045
1
1
3
Figure 45. 3.3 V to 5 V Line Transient, VOUT = 0.6 V, Load = 1 A
fSW = 600 kHz, Pulse Skip Enabled
VOUT
VOUT
2
2
VIN
VIN
SW
SW
CH2 10mV
M400µs
A CH3
4.84V
3
08143-043
CH1 5.0V
CH3 1.0V
CH1 2.0V
CH3 1.0V
Figure 43. 3.3 V to 5 V Line Transient, VOUT = 1.5 V, Load = 1 A
fSW = 1.2 MHz, Forced PWM
CH2 10mV
M400µs
A CH3
3.62V
Figure 46. 5 V to 3.3 V Line Transient, VOUT = 0.6 V, Load = 1 A
fSW = 600 kHz, Pulse Skip Enabled
Rev. 0 | Page 15 of 40
08143-046
1
1
3
ADP2114
VOUT, AC
2
VOUT
2
SW
VIN
3
SW
INDUCTOR CURRENT
1
CH1 2.0V
CH3 1.0V
CH2 10mV
M400µs
A CH3
4.84V
Figure 47. 3.3 V to 5 V Line Transient, VOUT = 0.6 V, Load = 1 A
fSW = 600 kHz, Forced PWM
CH3 2.0V
CH2 20mV
CH2 500mA
M1µs
A CH3
2.52V
08143-050
3
08143-047
4
Figure 50. Forced PWM Mode, CCM Operation, 200 mA Load, fSW = 600 kHz
VOUT, AC
VOUT
2
2
SW
VIN
SW
3
INDUCTOR CURRENT
1
CH2 10mV
M400µs
A CH3
3.50V
Figure 48. 5 V to 3.3 V Line Transient, VOUT = 0.6 V, Load = 1 A
fSW = 600 kHz, Forced PWM
CH3 2.0V
CH2 20mV
CH2 500mA
M1µs
A CH3
4.32V
08143-051
CH1 2.0V
CH3 1.0V
08143-048
4
3
Figure 51. Pulse Skip Enabled, DCM Operation, 200 mA Load, fSW = 600 kHz
VOUT, AC
2
EN2
1
SW
2
3
VOUT2
SS2
4
INDUCTOR CURRENT
SW
4
CH2 10mV
CH4 500mA
M4µs
A CH3
4.32V
CH1 5.0V
CH3 5.0V
Figure 49. Pulse Skip Mode, 110 mA Load
CH2 1.0V
CH4 2.0V
M1.0ms
A CH1
2.4V
Figure 52. Soft Start, Channel 2 VOUT = 1.8 V, CSS2 = 10 nF
Rev. 0 | Page 16 of 40
08143-052
CH3 2.0V
08143-049
3
ADP2114
INDUCTOR CURRENT
EN2
1
VOUT2
4
2
4
SS2
VOUT
2
SW
CH1 5.0V
CH3 5.0V
CH2 1.0V
CH4 500mV
M200µs
A CH1
2.4V
08143-053
3
CH3 5.0V
Figure 53. Start with Precharged Output
CH2 1.0V
CH4 2.0A
M2.0ms
A CH4
1.72V
08143-056
SW
3
Figure 56. Hiccup Mode, fSW = 600 kHz, 6.8 ms Hiccup Cycle
INDUCTOR CURRENT
INDUCTOR CURRENT
4
4
VOUT2
VOUT
2
2
CH2 1.0V
CH4 2.0A
M1.0ms
A CH2
1.12V
08143-054
CH3 5.0V
SW
3
CH3 5.0V
Figure 54. Current Limit Entry,
Channel 2 VOUT = 1.8 V, 2 A Configuration, fSW = 600 kHz
CH2 1.0V
CH4 2.0A
M2.0ms
A CH2
1.12V
08143-057
SW
3
Figure 57. Exit Hiccup Mode,
Channel 2 VOUT = 1.8 V, fSW = 600 kHz
EXTERNAL SYNC
INDUCTOR CURRENT
1
4
CHANNEL 1 SW
VOUT2
2
4
CHANNEL 2 SW
SW
M10.0µs
3
A CH2
1.12V
CH1 5.0V
CH3 5.0V
Figure 55. Current Limit Entry (Zoomed In),
Channel 2 VOUT = 1.8 V, 2 A Configuration, fSW = 600 kHz
M1.0µs
CH4 5.0V
A CH1
3.0V
08143-058
CH3 5.0V
CH2 1.0V
CH4 2.0A
08143-055
3
Figure 58. External Synchronization, fSYNC = 1.5 MHz, fSW = 750 kHz
Rev. 0 | Page 17 of 40
ADP2114
CHANNEL 1 SW
1
4
EN2
VOUT2
2
CHANNEL 2 SW
3
PGOOD2
INTERNAL CLKOUT
4
SW
1
M1.0µs
A CH3
3.0V
CH4 5.0V
CH1 5.0V
CH3 5.0V
Figure 59. Internal Clock Out, fSW = 600 kHz, fCLKOUT = 1.2 MHz
CH2 1.0V
CH4 2.0V
M200µs
A CH1
3.5V
08143-061
CH1 5.0V
CH3 5.0V
08143-059
3
Figure 61. Power Good Signal
CHANNEL 1 SW
INDUCTOR CURRENT, PHASE 2
CHANNEL 3 SW
1
4
2
INDUCTOR CURRENT, PHASE 1
2
PHASE 2 SW
3
CHANNEL 2 SW
CHANNEL 4 SW
CH2 2.0V
CH4 2.0V
M1.0µs
A CH1
1
2.0V
08143-060
CH1 2.0V
CH3 2.0V
PHASE 1 SW
CH1 5.0V
CH3 5.0V
Figure 60. 4-Channel Operation, Two ADP2114s, One Synchronizes Another,
90° Phase-Shifted Switch Nodes
Rev. 0 | Page 18 of 40
CH2 1.0A
CH4 1.0A
M1.0µs
A CH1
1.9V
Figure 62. Combined Dual-Phase Output Operation,
VOUT = 1.2 V, fSW = 1.1 MHz, 4 A Load
08143-062
3
4
ADP2114
BODE PLOTS
50
150
40
120
30
90
PHASE
10
60
30
0
0
MAGNITUDE
–10
–30
–20
–60
–30
–90
–40
–120
–50
1k
M1
10k
100k
M2
PHASE (Degrees)
MAGNITUDE (dB)
20
–150
FREQUENCY (Hz)
M1
54.86kHz
0.042dB
50.099°
M2
210.34kHz
–19.632dB
–0.412°
M2 – M1
155.48kHz
–19.673dB
–50.511°
08143-063
FREQUENCY
MAGNITUDE
PHASE
Figure 63. VIN = 5 V, VOUT = 3.3 V, Load = 2 A, fSW = 600 kHz, Crossover Frequency (fCO) = 55 kHz; Phase Margin 50° (See Table 12 for the Circuit Details)
50
120
40
96
30
72
PHASE
48
10
24
MAGNITUDE
0
0
–10
–24
–20
–48
–30
–72
–40
–96
–50
1k
10k
M1
100k
M2
PHASE (Degrees)
MAGNITUDE (dB)
20
–120
1M
FREQUENCY
MAGNITUDE
PHASE
M1
96.71kHz
–0.075dB
53.305°
M2
335.27kHz
–17.371dB
–0.389°
M2 – M1
238.56kHz
–17.296dB
–53.694°
08143-064
FREQUENCY (Hz)
Figure 64. VIN = 5 V, VOUT = 1.2 V, Load = 2 A, fSW = 1.2 MHz, Crossover Frequency (fCO) = 97 kHz; Phase Margin 53° (See Table 12 for the Circuit Details)
Rev. 0 | Page 19 of 40
ADP2114
SIMPLIFIED BLOCK DIAGRAM
VDD
UVLO
SCFG
FREQ
GND
OSC
SYNC/CLKOUT
UVLO
OSC_CH1
PHASE
SHIFT
OSC_CH2
VFB1
CLIM_CH1
OPCFG
PGOOD1
0.7V
CURRENT LIMIT/
CONFIGURATION
CLIM_CH2
PULSE SKIP ENABLE
VIN1
0.5V
VIN2
VIN3
EN1
GATE
CONTROL
LOGIC AND
MOSFET
DRIVERS
WITH
ANTI-SHOOT
THROUGH
PROTECTION
COMP1
UVLO
V1SET
VOUT
SELECTOR
FB1
OSC_CH1
VFB1
SS1
ISS =
6µA
–
+
+
PULSE SKIP
ENABLE
OTSD
gm ERROR
PMOS
NMOS
PGND1
PGND2
AMPLIFIER
VREF = 0.6V
PWM
COMPARATOR
HICCUP
TIMER
POWER
STAGE
VDD
SLOPE
COMPENSATION/
RAMP GENERATOR
–
+
CURRENT
LIMIT
COMPARATOR
CLIM_CH1
CURRENT SENSE
AMPLIFIER
CHANNEL 1
PGOOD2
0.7V
THERMAL
SHUTDOWN
SW1
SW2
OTSD
VFB2
VIN4
0.5V
VIN5
VIN6
EN2
GATE
CONTROL
LOGIC AND
MOSFET
DRIVERS
WITH
ANTI-SHOOT
THROUGH
PROTECTION
COMP2
UVLO
VOUT
SELECTOR
FB2
OSC_CH2
VFB2
SS2
ISS =
6µA
–
+
+
PULSE SKIP
ENABLE
OTSD
gm ERROR
PMOS
NMOS
PGND3
PGND4
AMPLIFIER
VREF = 0.6V
PWM
COMPARATOR
HICCUP
TIMER
POWER
STAGE
VDD
SLOPE
COMPENSATION/
RAMP GENERATOR
CURRENT
LIMIT
COMPARATOR
SW3
SW4
–
+
CLIM_CH2
Figure 65. Simplified Block Diagram
Rev. 0 | Page 20 of 40
CURRENT SENSE
AMPLIFIER
CHANNEL 2
08143-065
V2SET
ADP2114
THEORY OF OPERATION
The ADP2114 also includes undervoltage lockout (UVLO) with
hysteresis, soft start, and power good, as well as protection
features such as output short-circuit protection and thermal
shutdown. The output voltages, current limits, switching
frequency, pulse skip operation, and soft start time are
externally programmable with tiny resistors and capacitors.
CONTROL ARCHITECTURE
The ADP2114 consists of two step-down, dc-to-dc converters
that deliver regulated output voltages, VOUT1 and VOUT2 (see
Figure 1), by modulating the duty cycle at which the internal
high-side, P-channel power MOSFET and the low-side, N-channel
power MOSFET are switched on and off. In steady-state operation,
the output voltage, VOUT, is sensed on the feedback pin, FB1 (FB2),
and attenuated in proportion to the selected output voltage on
the V1SET (V2SET) pin. An error amplifier integrates the error
between the feedback voltage and the reference voltage (VREF =
0.6 V) to generate an error voltage at the COMP1 (COMP2) pin.
The valley inductor current is sensed by a current-sense amplifier
when the low-side, N-channel MOSFET is on. An internal
oscillator turns off the low-side, N-channel MOSFET and
turns on the high-side, P-channel MOSFET at a fixed switching
frequency. When the high,-side P-channel MOSFET is enabled,
the valley inductor current information is added to an emulated
ramp signal and compared to the error voltage by the PWM
comparator. The output of the PWM comparator modulates the
duty cycle by adjusting the trailing edge of the PWM pulse that
switches the power devices. Slope compensation is programmed
internally into the emulated ramp signal and automatically
selected, depending on the VIN, VOUT, and switching frequency.
This prevents subharmonic oscillations on the inductor current
for greater than 50% duty-cycle operation.
UNDERVOLTAGE LOCKOUT (UVLO)
The UVLO threshold is 2.65 V when VDD is increasing and
2.47 V when VDD is decreasing. The 180 mV hysteresis prevents
the converter from turning off and on repeatedly during a slow
voltage transition on VDD close to the 2.75 V minimum
operational level due to changing load conditions.
ENABLE/DISABLE CONTROL
The EN1 and EN2 pins are used to independently enable or
disable Channel 1 and Channel 2, respectively. Drive ENx high
to turn on the corresponding channel of ADP2114. Drive ENx
low to turn off the corresponding channel of ADP2114, reducing
input current below 1 μA. To force a channel to start automatically
when input power is applied, connect the corresponding ENx
to VDD. When shut down, the ADP2114 channels discharge
the soft start capacitor, causing a new soft start cycle every time
the converters are re-enabled.
SOFT START
The ADP2114 soft start feature allows the output voltage to ramp
up in a controlled manner, eliminating output voltage overshoot
during startup. Soft start begins after the undervoltage lockout
threshold is exceeded and the enable pin, EN1 (EN2), is pulled
high above 2.0 V. External capacitors to ground are required on
both the SS1 and SS2 pins. Each regulating channel has its own
soft start circuit. When the converter powers up and is enabled,
the internal 6 μA current source charges the external soft start
capacitor, establishing a voltage ramp slope at the SS1 (SS2) pin,
as shown in Figure 66. The soft start time period ends when the
soft start ramp voltage exceeds the internal reference of 0.6 V.
Control logic with the antishoot-through circuit monitor and
adjust the low-side and high-side driver outputs to ensure breakbefore-make switching. This monitoring and control prevents
crossconduction between the internal high-side, P-channel
power MOSFET and the low-side, N-channel power MOSFET.
Rev. 0 | Page 21 of 40
ENx
1
VOUT
2
4
SSx
SW
3
CH1 5.0V
CH3 5.0V
CH2 1.0V
CH4 2.0V
M1.0ms
Figure 66. Soft Start
A CH1
2.4V
08143-066
The ADP2114 is a high efficiency, dual, fixed switching frequency,
synchronous step-down, dc-to-dc converter with flex mode
architecture, which is the Analog Devices, Inc., proprietary
version of its peak current mode control architecture. The
device operates over an input voltage range of 2.75 V to 5.5 V.
Each output channel provides an adjustable output down to 0.6 V
and delivers up to 2 A of load current. When both the output
channels are tied together, they operate 180° out of phase to
deliver up to 4 A of load current. The integrated high-side,
P-channel power MOSFET and the low-side, N-channel power
MOSFET yield high efficiency at medium to heavy loads. Pulse
skip mode is available for improved efficiency at light loads. With
its high switching frequency (up to 2 MHz) and its integrated
power switches, the ADP2114 has been optimized to deliver
high performance in a small size for power management solutions.
ADP2114
The capacitance value of the soft start capacitor defines the soft
start time, tSS, based on
VREF I SS
=
t SS
CSS
(1)
where:
VREF is the internal reference voltage, 0.6 V.
ISS is the soft start current, 6 μA.
CSS is the soft start capacitor value.
The power good thresholds are shown in Figure 68. The PGOOD1
and PGOOD2 outputs also sink current if an overtemperature
condition is detected. Use these outputs as logical power good
signals by connecting the pull-up resistors from PGOOD1
(PGOOD2) to VDD. If the power good function is not used, the
pins can be left floating.
VOUT RISING
VOUT FALLING
100%
92%
% OF VOUT SET
108%
100%
84%
UNDERVOLTAGE
POWER
GOOD
OVERVOLTAGE
POWER
GOOD
UNDERVOLTAGE
ENx
PGOOD1
(PGOOD2)
1
VOUT
08143-068
If the output voltage VOUT1 (VOUT2) is precharged prior to enabling
Channel 1 (Channel 2), the control logic prevents inductor
current reversal by holding the power MOSFETs off until the
soft start voltage ramp at SS1 (SS2) reaches the precharged
output voltage on VFB1 (VFB2), see Figure 67.
% OF VOUT SET
116%
Figure 68. PGOOD1 and PGOOD2 Thresholds
2
PULSE SKIP MODE
SSx
4
SW
CH1 5.0V
CH3 5.0V
CH2 1.0V
CH4 500mV
M200µs
A CH1
2.4V
08143-067
3
Figure 67. Start with a Precharged Load
POWER GOOD
The ADP2114 features open-drain, power-good outputs
(PGOOD1 and PGOOD2) that indicate when the converter
output voltage is within regulation. The power good signal
transitions low immediately when the corresponding channel is
disabled.
The power good circuitry monitors the output voltage on the
FB1 (FB2) pin and compares it to the rising and falling
thresholds shown in Table 1. If the output voltage, VOUT1
(VOUT2), exceeds the typical rising limit of 116% of the target
output voltage, VOUT1SET (VOUT2SET), the PGOOD1 (PGOOD2)
pin pulls low. The PGOOD1 (PGOOD2) pin continues to pull
low until the output voltage recovers down to 108% (typical) of
the target value.
The ADP2114 has built-in, pulse skip circuitry that turns on
during light loads, switching only as necessary to maintain the
output voltage within regulation. This allows the converter to
maintain high efficiency during light load operation by reducing
the switching losses. The pulse skip mode can be selected by
configuring the OPCFG pin according to Table 7. In pulse skip
mode, when the output voltage dips below regulation, the
ADP2114 enters PWM mode for a few oscillator cycles to
increase the output voltage back to regulation. During the
wait time between bursts, both power switches are off, and the
output capacitor supplies all load current. Because the output
voltage dips and recovers occasionally, the output voltage ripple
in this mode is larger than the ripple in the PWM mode of
operation.
If the converter is configured to operate in forced PWM mode
(by selecting that configuration on the OPCFG pin), the device
operates with a fixed switching frequency, even at light loads.
If the output voltage drops below 84% of the target output voltage,
the corresponding PGOOD1 (PGOOD2) pin pulls low. The
PGOOD1 (PGOOD2) pin continues to pull low until the output
voltage rises to within 92% of the target output voltage. The
PGOOD1 (PGOOD2) pin then releases and signals the return
of the output voltage within the power good window.
Rev. 0 | Page 22 of 40
ADP2114
HICCUP MODE CURRENT LIMIT
MAXIMUM DUTY CYCLE OPERATION
The ADP2114 features a hiccup mode current limit
implementation. When the peak inductor current exceeds
the preset current limit for more than eight consecutive clock
cycles, the hiccup mode current limit condition occurs. The
channel then goes to sleep for 6.8 ms (at a 600 kHz switching
frequency), which is enough time for the output to discharge
and the average power dissipation to reduce. It then wakes up
with a soft start period (see Figure 69). If the current limit
condition is triggered again, the channel goes to sleep and
wakes up after 6.8 ms. The current limits for the two channels
are programmed by configuring the OPCFG pin (see Table 7).
For the 2 A/2 A option, the output current limit is set to 3.3 A
per output. For the 3 A/1 A option, the current limits are set to
4.5 A and 1.9 A for VOUT1 and VOUT2, respectively.
As the input voltage drops and approaches the output voltage,
the ADP2114 smoothly transitions to maximum duty cycle
operation, maintaining the low-side, N-channel MOSFET switch
on for the minimum off time. In maximum duty cycle operation,
the output voltage dips below regulation because the output
voltage is the product of the input voltage and the maximum
duty cycle limitation. The maximum duty cycle limit is a
function of the switching frequency and the input voltage,
as shown in Figure 72.
INDUCTOR
CURRENT
4
VOUT
2
SW
CH3 5.0V
CH2 1.0V
CH4 2A
M2.0ms
A CH4
1.72A
08143-069
3
Figure 69. Hiccup Mode
THERMAL OVERLOAD PROTECTION
The ADP2114 has an internal temperature sensor that monitors
the junction temperature. High current going into the switches
or a hot printed circuit board (PCB) can cause the junction
temperature of the ADP2114 to rise rapidly. When the junction
temperature reaches approximately 150°C, the ADP2114 goes
into thermal shutdown and the converter is turned off. When the
junction temperature drops below 125°C, the ADP2114 resumes
normal operation after the soft start sequence.
SYNCHRONIZATION
The ADP2114 can be synchronized to an external clock such
that the two channels operate at a switching frequency that is
half the input synchronization clock. The SYNC/CLKOUT pin
can be configured as an input SYNC pin or an output CLKOUT
pin through the SCFG pin, as shown in Table 6. Through the input
SYNC pin, the ADP2114 can be synchronized to an external clock
such that the two channels switch at half the external clock, 180°
out of phase. Through the output CLKOUT pin, the ADP2114
provides an output clock that is twice the switching frequency of
the channels and 90° out of phase. Therefore, a single ADP2114
configured for the CLKOUT option acts as the master converter
and provides an external clock for all other dc-to-dc converters
(including other ADP2114s). These other converters are configured
as slaves that accept an external clock and synchronize to it.
This clock distribution approach synchronizes all dc-to-dc
converters in the system and prevents beat harmonics that
can lead to EMI issues.
The ADP2114 has been optimized to power high performance
signal chain circuits. The slew rate of the switch node is
controlled by the size of the driver devices. Fast slewing of the
switch node is desirable to minimize transition losses but can
lead to serious EMI issues due to parasitic inductance. Therefore,
the slew rate of the drivers has been optimized such that the
ADP2114 can match the performance of the low dropout
regulators in supplying sensitive signal chain circuits while
providing excellent power efficiency.
Rev. 0 | Page 23 of 40
ADP2114
CONVERTER CONFIGURATION
RV2SET (Ω) ± 5%
0 to GND
4.7 k to GND
8.2 k to GND
15 k to GND
27 k to GND
47 k to GND
82 k to GND
0 to VDD
VOUT2 (V)
0.8
1.2
1.5
1.8
2.5
3.3
0.6 to <1.6
(adjustable)
1.6 to 3.3
(adjustable)
where:
VREF is 0.6 V, the internal reference.
ISTRING is the resistor divider string current.
When R1 is determined, calculate the value of the top resistor,
R2, by
If the required output voltage VOUT1 (VOUT2) is in the adjustable
range, from 0.6 V to less than 1.6 V, connect V1SET (V2SET)
through an 82 kΩ resistor to GND. For the adjustable output
voltage range of 1.6 V to 3.3 V, tie V1SET (V2SET) to VDD (see
Table 4). The adjustable output voltage of ADP2114 is externally
set by a resistive voltage divider from the output voltage to the
feedback pin (see Figure 71). The ratio of the resistive voltage
divider sets the output voltage, while the absolute value of those
resistors sets the divider string current. For lower divider string
currents, the small 10 nA (0.1 μA maximum) FB bias current
should be taken into account when calculating the resistor
values. The FB bias current can be ignored for a higher divider
string current; however, this degrades efficiency at very light loads.
⎡V
− VREF ⎤
R2 = R1⎢ OUT
⎥
⎣ VREF
⎦
(3)
VIN
RFREQ
V1SET/
V2SET
RV1SET /
RV2SET
VINx
ADP2114
VOUT1/VOUT2
SWx
L
FB1/FB2
GND
PGNDx
COMP1/
COMP2
Figure 70. Configuration for Fixed Outputs
VIN
RFREQ
V1SET/
V2SET
RV1SET /
RV2SET
VINx
ADP2114
VOUT1/VOUT2
L
SWx
R2
FB1/FB2
PGNDx
GND
COMP1/
COMP2
R1
08143-071
0 to VDD
VOUT1 (V)
0.8
1.2
1.5
1.8
2.5
3.3
0.6 to <1.6
(adjustable)
1.6 to 3.3
(adjustable)
(2)
08143-070
Table 4. Output Voltage Programming
RV1SET (Ω) ± 5%
0 to GND
4.7 k to GND
8.2 k to GND
15 k to GND
27 k to GND
47 k to GND
82 k to GND
R1 = VREF/ISTRING
VDD
FREQ
To set the output voltage, VOUT1 (VOUT2), select one of the six
fixed voltages, as shown in Table 4, by connecting the V1SET
(V2SET) pin to GND through an appropriate value resistor (see
Figure 70). V1SET and V2SET set the voltage output levels for
Channel 1 and Channel 2, respectively. The feedback pin FB1
(FB2) should be directly connected to VOUT1 (VOUT2).
To limit output voltage accuracy degradation due to FB bias
current to less than 0.05% (0.5% maximum), ensure that the
divider string current is greater than 20 μA. To calculate the
desired resistor values, first determine the value of the bottom
divider string resistor, R1, by
VDD
FREQ
SELECTING THE OUTPUT VOLTAGE
Figure 71. Configuration for Adjustable Outputs
Rev. 0 | Page 24 of 40
ADP2114
SETTING THE OSCILLATOR FREQUENCY
The ADP2114 channels can be set to operate in one of the three
preset switching frequencies: 300 kHz, 600 kHz, or 1.2 MHz.
For 300 kHz operation, connect the FREQ pin to GND. For
600 kHz or 1.2 MHz operation, connect a resistor between the
FREQ pin and GND, as shown in Table 5.
An external clock can be applied to the SYNC/CLKOUT pin
when configured as an input to synchronize multiple ADP2114s
to the same external clock. The fSYNC range is 400 kHz to 4 MHz,
which produces fSW in the 200 kHz to 2 MHz range. See Figure 73
for an illustration.
VIN
27kΩ
27kΩ
Table 5. Oscillator Frequency Setting
fSW (kHz)
300
600
1200
SCFG
FREQ
SCFG
VDD
SYNC
(fSW = fSYNC /2)
ADP2114
fSYNC
Choice of the switching frequency depends on the required
dc-to-dc conversion ratio and is limited by the minimum and
maximum controllable duty cycle shown on Figure 72. This is
due to the requirement of minimum on and minimum off times
for current sensing and robust operation. The choice of
switching frequency is also determined by the need for small
external components. For small, area limited power solutions,
use of higher switching frequencies is recommended.
FREQ
VDD
SYNC
(fSW = fSYNC /2)
ADP2114
EXTERNAL CLOCK (2.4MHz)
08143-073
RFREQ (Ω) ± 5%
0 to GND
8.2 k to GND
27 k to GND
TO OTHER ADP2114
Figure 73. Synchronization with External Clock (fSW = 1.2 MHz in This Case)
When synchronizing to an external clock, the switching
frequency fSW must be set close to half of the expected external
clock frequency by appropriately terminating the FREQ pin as
shown in Table 5.
VIN
8.2kΩ
8.2kΩ
90
SCFG
80
SYNC
(fSW = fSYNC /2)
70
60
50
40
SCFG
VDD
FREQ
VDD
CLKOUT
(fSW = 2 × fSW)
ADP2114
MAXIMUM LIMIT
MINIMUM LIMIT; VIN = 2.75V
ADP2114
fSYNC = 2 × fSW
MINIMUM LIMIT; VIN = 3.3V
TO OTHER ADP2114
MINIMUM LIMIT; VIN = 5.5V
NOTES
1. fSW = 600kHz SET FOR BOTH ADP2114.
30
Figure 74. ADP2114 to SYNC with Another ADP2114
(Note that the SCFG of the master is tied to VDD.)
20
400
600
800
1000
SWITCHING FREQUENCY (kHz)
1200
08143-072
10
0
200
FREQ
08143-074
DUTY-CYCLE LIMITS (%)
100
Figure 72. Duty Cycle Working Limits
For single output, multiphase applications that operate at close
to 50% duty cycle, it is recommended to use the 1.2 MHz
switching frequency to minimize crosstalk between the phases.
The ADP2114 can also be configured to output a clock signal
on the SYNC/CLKOUT pin to synchronize multiple ADP2114s
to it (see Figure 74). The CLKOUT signal is 90º phase shifted to
the internal clock of the channels so that the master ADP2114
and the slave channels are out of phase (see Figure 75 for
additional information).
CHANNEL 1 SW
SYNCHRONIZATION AND CLKOUT
The ADP2114 can be configured to output an internal clock or
synchronize to an external clock at the STNC/CLKOUT pin.
The SYNC/CLKOUT pin is a bidirectional pin configured by
the SCFG pin, as shown in Table 6.
4
CHANNEL 2 SW
3
Table 6. SYNC/CLKOUT Configuration Setting
SYNC/CLKOUT
Input
Output
1
INTERNAL CLKOUT
The converter switching frequency, fSW, is half of the synchronization frequency fSYNC/fCLKOUT as shown in Equation 4, irrespective
of whether SYNC/CLKOUT is configured as an input or output.
fSYNC/fCLKOUT = 2 × fSW
(4)
Rev. 0 | Page 25 of 40
CH1 5.0V
CH3 5.0V
M1.0µs
A CH4
CH4 5.0V
Figure 75. CLKOUT Waveforms
3.00V
08143-075
SCFG
GND
VDD
ADP2114
OPERATION MODE CONFIGURATION
The dual-channel ADP2114 can be configured to one of the four
modes of operation by connecting the OPCFG pin as shown in
Table 7. This configuration sets the current limit for each
channel and enables or disables the transition to pulse skip mode
at light loads.
In the dual-phase configuration, the outputs of the two channels
are connected together, and they generate a single dc output
voltage, VOUT. For this single combined dual-phase output,
only Mode 2 in the OPCFG options can be used. In this mode,
the error amplifiers of both phases are used. The feedback
pins (FB1 and FB2) are tied together, the compensation pins
(COMP1 and COMP2) are tied together, the soft start pins (SS1
and SS2) are tied together, and the enable pins (EN1 and EN2)
are tied together.
In addition, if the power-good feature is used, combine PGOOD1
and PGOOD2 and connect them to VDD through a single
pull-up resistor.
When the ADP2114 is synchronized to an external clock, the
converters always operate in fixed frequency CCM, and they do
not enter into pulse skip mode at light loads. In this case, when
configuring the OPCFG pin, choose forced PWM mode.
Table 7. Current Limit Operation Mode and Configuration
Mode
1
2
3
4
ROPCFG (Ω) ± 5%
0 to GND
4.7 k to GND
8.2 k to GND
15 k to GND
Maximum Output Current
IOUT1 (A)/IOUT2 (A)
2/2
2/2
3/1
3/1
Peak Current Limit
ILIMIT1 (A)/ILIMIT2 (A)
3.3/3.3
3.3/3.3
4.5/1.9
4.5/1.9
Rev. 0 | Page 26 of 40
Power Savings at Light Load
Pulse skip enabled
Forced PWM
Pulse skip enabled
Forced PWM
ADP2114
EXTERNAL COMPONENTS SELECTION
INPUT CAPACITOR SELECTION
The input current to a buck converter is pulsating in nature. The
current is zero when the high-side switch is off and approximately
equal to the load current when it is on. Because this occurs at
reasonably high frequencies (300 kHz to 1.2 MHz), the input
bypass capacitor ends up supplying most of the high frequency
current (ripple current), allowing the input power source to
supply only the average (dc) current. The input capacitor needs a
sufficient ripple current rating to handle the input ripple as well
as an ESR that is low enough to mitigate the input voltage
ripple. For the ADP2114, place a 22 μF, 6.3 V, X5R ceramic
capacitor close to the VINx pin for each channel. X5R or X7R
dielectrics are recommended with a voltage rating of 6.3 V or
10 V. Y5V and Z5U dielectrics are not recommended due to
their poor temperature and dc bias characteristics.
VDD RC FILTER
It is recommended to apply the input power, VIN, to the VDD pin
through a low-pass RC filter, as shown on Figure 76. Connecting a
10 Ω resistor in series with VIN and a 1 μF, 6.3 V, X5R (or X7R)
ceramic capacitor between VDD and GND creates a 16 kHz
(−3 dB) low-pass filter that effectively attenuates voltage glitches
on the input power rail caused by the switching regulator. This
provides a clean power supply to the internal, sensitive, analog
and digital circuits in the ADP2114, ensuring robust operation.
10Ω
1µF
VDD
ADP2114
GND
08143-076
VIN
Figure 76. Low-Pass Filter at VDD
INDUCTOR SELECTION
The high switching frequency of ADP2114 allows for minimal
output voltage ripple even with small inductors. The sizing of the
inductor is a trade-off between efficiency and transient response. A
small inductor leads to larger inductor current ripple that provides
excellent transient response but degrades efficiency. Due to
the high switching frequency of ADP2114, shielded ferrite core
inductors are recommended for their low core losses and low EMI.
As a guideline, the inductor peak-to-peak current ripple, ΔIL, is
typically set to 1/3 of the maximum load current for optimal
transient response and efficiency.
ΔI L =
VOUT × (VIN − VOUT ) I LOAD (MAX )
≈
VIN × f SW × L
3
⇒ LIDEAL =
3 × VOUT × (VIN − VOUT )
f SW × VIN × I LOAD ( MAX )
The internal slope compensation introduces additional limitations
on the optimal inductor value for stable operation because the
internal ramp is scaled for each VOUT setting. The limits for
different VIN, VOUT, and fSW combinations are listed in Table 8.
Table 8. Minimum and Maximum Inductor Values
fSW (kHz)
300
300
300
300
300
300
300
300
300
300
300
600
600
600
600
600
600
600
600
600
600
600
1200
1200
1200
1200
1200
1200
1200
1200
1200
VIN (V)
5
5
3.3
5
3.3
5
3.3
5
3.3
5
3.3
5
5
3.3
5
3.3
5
3.3
5
3.3
5
3.3
5
5
3.3
5
3.3
5
3.3
5
3.3
VOUT (V)
3.3
2.5
2.5
1.8
1.8
1.5
1.5
1.2
1.2
0.8
0.8
3.3
2.5
2.5
1.8
1.8
1.5
1.5
1.2
1.2
0.8
0.8
2.5
1.8
1.8
1.5
1.5
1.2
1.2
0.8
0.8
Min L (μH)
6.8
5.6
5.6
4.7
4.7
2.2
2.2
2.2
2.2
1.5
1.5
3.3
3.3
3.3
2.2
2.2
1.5
1.5
1.5
1.5
1.0
1.0
1.0
1.0
1.0
0.8
0.8
0.8
0.8
0.47
0.47
Max L (μH)
10
15
6.8
12
8.2
12
8.2
10
8.2
6.8
6.8
4.7
6.8
3.3
6.8
3.3
5.6
4.7
4.7
3.3
3.3
3.3
3.3
3.3
2.2
2.2
2.2
2.2
2.2
1.5
1.5
To avoid saturation, the rated current of the inductor has to be
larger than the maximum peak inductor IL_PEAK current given by
I L _ PEAK = I LOAD _ MAX +
ΔI L
2
where:
ILOAD_MAX is the maximum dc load current.
ΔIL is the inductor ripple current (peak to peak).
(5)
where:
VIN is the input voltage on the VINx terminal.
VOUT is the desired output voltage.
fSW is the converter switching frequency.
Rev. 0 | Page 27 of 40
(6)
ADP2114
The ADP2114 can be configured in either a 2 A/2 A or a 3 A/1 A
current limit configuration and, therefore, the current limit
thresholds for the two channels are different in each setting.
The inductor chosen for each channel must have at least the
peak output current limit of the IC in each case for robust
operation during short-circuit conditions. The following
inductors are recommended:
OUTPUT CAPACITOR SELECTION
The output capacitor selection affects both the output voltage
ripple and the loop dynamics of the converter. The ADP2114
is designed for operation with small ceramic output capacitors
that have low ESR and ESL; therefore, comfortably able to meet
tight output voltage ripple specifications. X5R or X7R dielectrics
are recommended with a voltage rating of 6.3 V or 10 V. Y5V
and Z5U dielectrics are not recommended due to their poor
temperature and dc bias characteristics. The minimum output
capacitance, COUT_MIN, is determined by Equation 7 and
Equation 8.
⎞
⎟
⎟
⎠
(7)
Therefore,
COUT_MIN ≅
ΔI L
8 × f SW × (ΔVRIPPLE — ΔI L × ESR)
•
Select the largest output capacitance given by Equation 8 and
Equation 9. While choosing the actual type of ceramic capacitor
for the output filter of the converter, pick one with a nominal
capacitance that is 20% to 30% larger than the calculated value
because the effective capacitance decreases with larger dc voltages.
In addition, the rated voltage of the capacitor must be higher
than the output voltage of the converter.
Recommended input and output ceramic capacitors include
•
•
•
•
Murata GRM21BR61A106KE19L, 10 μF, 10 V, X5R, 0805
TDK C2012X5R0J226M, 22 μF, 6.3 V, X5R, 0805
Panasonic ECJ-4YB0J476M, 47 μF, 6.3 V, X5R, 1210
Murata GRM32ER60J107ME20L, 100 μF, 6.3 V, X5R, 1210
CONTROL LOOP COMPENSATION
For acceptable maximum output voltage ripple,
⎛
1
ΔVRIPPLE ≅ ΔI L × ⎜ ESR +
⎜
×
×
8
f
SW COUT_MIN
⎝
•
The inductor value is based on the peak-to-peak current
being 30% of the maximum load current.
Voltage drops across the internal MOSFET switches and
across the dc resistance of the inductor are ignored.
In Equation 9, it is assumed that it takes up to three switching
cycles until the loop adjusts the inductor current in response
to the load step.
The ADP2114 uses a peak, current mode control architecture
for excellent load and line transient response. The external
voltage loop is compensated by a transconductance amplifier
with a simple external RC network between the COMP1
(COMP2) pin and GND, as shown in Figure 77.
(8)
ADP2114
where:
ΔVRIPPLE is allowable peak-to-peak output voltage ripple in volts.
ΔIL is the inductor ripple current.
ESR is the equivalent series resistance of the capacitor in ohms.
fSW is the converter switching frequency in Hertz.
If there is a step load, choose the output capacitor value based
on the value of the step load. For the maximum acceptable
output voltage droop/overshoot caused by the step load,
COUT_MIN
⎛
3
≅ ΔI OUT_STEP × ⎜⎜
×
f
ΔV
DROOP
⎝ SW
⎞
⎟
⎟
⎠
VFBx
COMPx
RCOMP
gm
CC2
CCOMP
0.6V
GND
Figure 77. Compensation Components
The basic control loop block diagram is shown in Figure 78.
VIN
INDUCTOR
CURRENT
SENSE
(9)
PULSE
WIDTH
MODULATOR
where:
ΔIOUT_STEP is the load step value in amperes.
fSW is the switching frequency in Hertz.
ΔVDROP is the maximum allowable output voltage
droop/overshoot in volts for the load step.
VCOMP
CCOMP
IL
VOUT
gm
VREF = 0.6V
ADP2114
RCOMP
08143-078
•
From 0.47 μH to 4.7 μH, the TOKO D53LC and
FDV0620 series
From 4.7 μH to 12 μH, the Cooper Bussman DR1050 series
and the Wurth Elektronik WE-PDF series.
•
08143-077
•
Note that the previous equations are approximations and are
based on following assumptions:
Figure 78. Basic Control Block Diagram
The blocks and components shown enclosed within the dashed line
in Figure 78 are embedded inside each channel of the ADP2114.
Rev. 0 | Page 28 of 40
ADP2114
The control loop can be broken down into the following three
sections:
• VOUT to VCOMP
• VCOMP to IL
• IL to VOUT
Correspondingly, there are three transfer functions:
ZCOMP ( fCROSS ) =
VCOMP(s) VREF
=
× g m × ZCOMP(s)
VOUT (s) VOUT
(10)
I L(s)
= GCS
VCOMP(s)
(11)
VOUT (s)
= Z FILT (s)
I L(s)
(12)
where:
gm is the transconductance of the error amplifier, 550 μs.
GCS is the current sense gain, 4 A/V.
VOUT is the output voltage of the converter.
VREF is the internal reference voltage of 0.6 V.
ZCOMP(s) is the impedance of the RC compensation network that
forms a pole at origin and a zero as expressed in Equation 13.
ZCOMP(s) =
1 + s × RCOMP × CCOMP
s × CCOMP
(13)
ZFILT(s) is the impedance of the output filter and is expressed as
ZFILT(s) =
RLOAD
1 + s × RLOAD × COUT
At the crossover frequency, the gain of the open-loop transfer
function is unity. This yields Equation 16 for the compensation
network impedance at the crossover frequency.
f ZERO =
f
1
≈ CROSS
2 × π × RCOMP × CCOMP
8
(17)
Solving Equation 16 and Equation 17 simultaneously yields the
value for the compensation resistor and compensation
capacitor, as shown in Equation 18 and Equation 19.
⎛ (2 π)FCROSS
RCOMP = 0.9 × ⎜⎜
⎝ GmGCS
CCOMP =
⎞ ⎛ COUT VOUT
⎟×⎜
⎟ ⎜ V
REF
⎠ ⎝
1
2 × π × f ZERO × RCOMP
⎞
⎟
⎟
⎠
(18)
(19)
The capacitor CC2 (as shown in Figure 77) forms a pole with the
compensation resistor, RCOMP, in the feedback loop to ensure
that the loop gain keeps rolling off well beyond the unity-gain
crossover frequency. The value of CC2, if used, is typically set to
1/40 of the compensation capacitor, CCOMP.
(14)
The overall loop gain, H(s), is obtained by multiplying the three
transfer functions previously mentioned as follows:
VREF
× ZCOMP(s) × ZFILT(s)
VOUT
(16)
To ensure that there is sufficient phase margin at the crossover
frequency, place the compensator zero at 1/8 of the crossover
frequency, as shown in Equation 17.
where s is angular frequency that can be written as s = 2πf.
H(s) = gM × GCS ×
2 × π × fCROSS × COUT VOUT
×
g m × GCS
VREF
(15)
When the switching frequency (fSW), output voltage (VOUT), output
inductor (L), and output capacitor (COUT) values are selected,
the unity crossover frequency of 1/12 (approximately) the
switching frequency can be targeted.
Rev. 0 | Page 29 of 40
ADP2114
DESIGN EXAMPLE
The external component selection procedure from the Control
Loop Compensation section is used for this design example.
3.
L=
Table 9. 2-Channel Step-Down DC-to-DC Converter
Requirements
Parameter
Input Voltage, VIN
Channel 1, VOUT1
Specification
5.0 V ±10%
3.3 V, 2 A, 1% VOUT
ripple (p-p)
Channel 2, VOUT2
1.8 V, 2 A, 1% VOUT
ripple (p-p)
Pulse-Skip Feature
Enabled
Therefore, when L = 3.3 μH (the closest standard value) in
Equation 3, ΔIL = 0.566 A.
Although the maximum output current required is 2 A, the
maximum peak current is 3.3 A under the current limit
condition (see Table 7). Therefore, the inductor should be
rated for 3.3 A of peak current and 3 A of average current
for reliable circuit operation.
CHANNEL 1 CONFIGURATION AND COMPONENTS
SELECTION
VOUT
V IN
ΔI L
8 × f SW × (ΔVRIPPLE - ΔI L × ESR)
⎛
3
COUT_MIN ≅ ΔIOUT_STEP × ⎜⎜
⎝ f SW × ΔVDROOP
For the target output voltage, VOUT = 3.3 V, connect the
V1SET pin through a 47 kΩ resistor to GND (see Table 4).
Because one of the fixed output voltage options is chosen,
the feedback pin (FB1) must be directly connected to the
output of Channel 1, VOUT1.
Estimate the duty-cycle, D, range. Ideally,
D=
Select the output capacitor by using Equation 8 and
Equation 9.
COUT_MIN ≅
Complete the following steps to configure Channel 1:
2.
(VIN − VOUT ) VOUT
×
VIN
ΔI L × f SW
In Equation 5, VIN = 5 V, VOUT = 3.3 V, ΔIL = 0.3 × IL = 0.6 A,
and fSW = 600 kHz, which results in L = 3.11 μH.
Additional
Requirements
None
Maximum load step:
1 A to 2 A, 5% droop
maximum
Maximum load step:
1 A to 2 A, 5% droop
maximum
None
4.
1.
Select the inductor by using Equation 5.
⎞
⎟
⎟
⎠
Equation 8 is based on the output ripple (ΔVRIPPLE), and
Equation 9 is for capacitor selection based on the transient
load performance requirements that allow, in this case, 5%
maximum deviation. As previously mentioned, perform
these calculations and choose whatever equation yields the
larger capacitor size.
(20)
That gives the duty cycle for the 3.3 V output voltage and
the nominal input voltage of DNOM = 0.66 at VIN = 5.0 V.
In this case, the following values are substituted for the
variables in Equation 8 and Equation 9:
The minimum duty cycle, DMIN, for the maximum input
voltage (10% above the nominal) is DMIN = 0.60 at VIN
maximum = 5.5 V
ΔIL = 0.566 A
fSW = 600 kHz
ΔVRIPPLE = 33 mV (1% of 3.3 V)
ESR = 3 mΩ (typical for ceramic capacitors)
ΔIOUT_STEP = 1 A
ΔVDROOP = 0.165 V (5% of 3.3 V)
The maximum duty cycle, DMAX, for the minimum input
voltage (10% less than nominal) is DMAX = 0.73 at VIN
minimum = 4.5 V.
However, the actual duty cycle is larger than the calculated
values to compensate for the power losses in the converter.
Therefore, add 5% to 7% at the maximum load.
The output ripple based calculation (see Equation 8) dictates
that COUT = 4.0 μF, whereas the transient load based
calculation (see Equation 9) dictates that COUT = 30 μF. To
meet both requirements, choose the latter. As previously
mentioned in the Control Loop Compensation section, the
capacitor value reduces with applied dc bias; therefore, select a
higher value. In this case, the next higher value is 47 μF
with a minimum voltage rating of 6.3 V.
Based on the estimated duty-cycle range, choose the
switching frequency according to the minimum and
maximum duty-cycle limitations, as shown in Figure 72.
For the Channel 1 VIN = 5 V and VOUT = 3.3 V combination,
choose fSW = 600 kHz with a maximum duty cycle of 0.8.
This frequency option provides the smallest sized solution.
If a higher efficiency is required, choose the 300 kHz option.
However, the PCB footprint area of the converter will be
larger because of the bigger inductor and output capacitors.
5.
Rev. 0 | Page 30 of 40
Calculate the feedback loop, compensation component
values by using Equation 15.
H(s) = gM × GCS ×
VREF
× ZCOMP(s) × ZFILT(s)
VOUT
ADP2114
The switching frequency (fSW) of 600 kHz, which is chosen
based on the Channel 1 requirements, meets the duty cycle
ranges that have been previously calculated. Therefore, this
switching frequency is acceptable.
In this case, the following values are substituted for the
variables in Equation 18:
gm = 550 μs
GCS = 4A/V
VREF = 0.6 V
VOUT = 3.3 V
COUT = 0.8 × 47 μF (capacitance derated by 20% to account
for dc bias).
3.
L=
RCOMP = 27 kΩ.
Substituting RCOMP in Equation 19 yields CCOMP = 1000 pF.
Although the maximum output current required is 2 A, the
maximum peak current is 3.3 A under the current limit
condition (see Table 7). Therefore, the inductor should be
rated for 3.3 A of peak current and 3 A of average current
for reliable circuit operation under all conditions.
Table 10. Channel 1 Circuit Settings
Setting
Step 1
Fixed, typical
Fixed, typical
Fixed, typical
Step 2
1/12 fSW
1/8 fCROSS
Step 3
Step 4
Equation 18
Equation 19
Value
3.3 V
0.6 V
550 μs
4 A/V
600 kHz
50 kHz
6.25 kHz
3.3 μH
47 μF, 6.3 V
27 kΩ
1000 pF
4.
CHANNEL 2 CONFIGURATION AND COMPONENTS
SELECTION
Complete the following steps to configure Channel 2:
1.
2.
For the target output voltage, VOUT = 1.8 V, connect the
V2SET pin through a 15 kΩ resistor to GND (see Table 4).
Because one of the fixed output voltage options is chosen,
the feedback pin (FB2) must be directly connected to the
output of Channel 2, VOUT2.
Estimate the duty-cycle, D, range (see Equation 20). Ideally,
D=
(VIN − VOUT ) VOUT
×
ΔI L × f SW
VIN
In Equation 5, VIN = 5 V, VOUT = 1.8 V, ΔIL = 0.3 × IL =
0.6 A, and fSW = 600 kHz, which results in L = 2.9 μH.
Therefore, when L = 3.3 μH (the closest standard value) in
Equation 3, ΔIL = 0.582 A.
From Equation 18,
Circuit Parameter
Output Voltage, VOUT
Reference Voltage, VREF
Error Amp Transconductance, gm
Current Sense Gain, CCS
Switching Frequency, fSW
Crossover Frequency, fC
Zero Frequency, fZERO
Output Inductor, LOUT
Output Capacitor, COUT
Compensation Resistor, RCOMP
Compensation Capacitor, CCOMP
Select the inductor by using Equation 5.
VOUT
V IN
That gives the duty cycle for the 1.8 V output voltage and
the nominal input voltage of DNOM = 0.36 at VIN = 5.0 V.
The minimum duty cycle for the maximum input voltage (10%
above the nominal) is DMIN = 0.33 at VIN maximum = 5.5 V.
The maximum duty cycle for the minimum input voltage (10%
less than nominal) is DMAX = 0.4 at VIN minimum = 4.5 V.
However, the actual duty cycle is larger than the calculated
values to compensate for the power losses in the converter.
Therefore, add 5% to 7% at the maximum load.
Rev. 0 | Page 31 of 40
Select the output capacitor by using Equation 8 and
Equation 9.
COUT_MIN ≅
ΔI L
8 × f SW × (ΔVRIPPLE - ΔI L × ESR)
⎛
3
COUT_MIN ≅ ΔI OUT_STEP × ⎜⎜
f
ΔV
×
DROOP
⎝ SW
⎞
⎟
⎟
⎠
Equation 8 is based on the output ripple (ΔVRIPPLE), and
Equation 9 is for capacitor selection based on the transient
load performance requirements that allow, in this case, 5%
maximum deviation. As mentioned earlier, perform these
calculations and choose whatever equation yields the larger
capacitor size.
In this case, the following values are substituted for the
variables in Equation 8 and Equation 9:
ΔIL = 0.582 A
fSW = 600 kHz
ΔVRIPPLE = 18 mV (1% of 1.8 V)
ESR = 3 mΩ (typical for ceramic capacitors)
ΔIOUT_STEP = 1 A
ΔVDROOP = 0.09 V (5% of 1.8 V)
The output ripple based calculation (see Equation 8) dictates
that COUT = 7.7 μF, whereas the transient load based
calculation (see Equation 9) dictates that COUT = 55 μF. To
meet both requirements, choose the latter. As previously
mentioned in the Control Loop Compensation section, the
capacitor value reduces with applied dc bias; therefore, select
a higher value. In this case, choose a 47 μF/6.3 V capacitor
and a 22 μF/6.3 V capacitor in parallel to meet the
requirements.
ADP2114
5.
Calculate the feedback loop, compensation component
values by using Equation 15.
SYSTEM CONFIGURATION
Complete the following steps to further configure the ADP2114
for this design example:
V
H(s) = gm × GCS × REF × ZCOMP(s) × ZFILT(s)
VOUT
1.
In this case, the following values are substituted for the
variables in Equation 18:
2.
gm = 550 μs
GCS = 4
VREF = 0.6 V
VOUT = 1.8 V
COUT = 0.8 × (47+22) μF (capacitance derated by 20% to
account for dc bias).
From Equation 18,
RCOMP = 22 kΩ.
Substituting RCOMP in Equation 19 yields CCOMP = 1100 pF.
3.
Set the switching frequency (fSW) = 600 kHz (see Table 5)
by connecting the FREQ pin through an 8.2 kΩ resistor
to GND.
Tie SCFG to VDD and use the CLKOUT signal to
synchronize other converters on the same board with the
ADP2114.
Tie OPCFG to GND for 2 A/2 A maximum output current
operation and to enable pulse skip mode at light load
conditions (see Table 7).
A schematic of the ADP2114 as configured in the design example
described in this section is shown in Figure 79.
Table 12 provides the recommended inductor, output capacitor,
and compensation component values for a set of popular input
and output voltage combinations.
Table 11. Channel 2 Circuit Settings
Circuit Parameter
Output Voltage, VOUT
Reference Voltage, VREF
Error Amp Transconductance, gm
Current Sense Gain, CCS
Switching Frequency, fSW
Crossover Frequency, fCROSS
Zero Frequency, fZERO
Output Inductor, LOUT
Output Capacitors, COUT
Compensation Resistor, RCOMP
Compensation Capacitor, CCOMP
Setting
Nominal
Typical
Typical
Typical
Step 2
1/12 fSW
1/8 fCROSS
Step 3
Step 4
Equation 18
Equation 19
Value
1.8 V
0.6 V
550 μs
4 A/V
600 kHz
50 kHz
6.25 kHz
3.3 μF
47 μF + 22 μF
22 kΩ
1100 pF
Table 12. Selection Table of L, COUT, and Compensation Values
fSW (kHz)
300
300
300
300
600
600
600
600
1200
1200
1200
1200
VIN (V)
5
5
5
5
5
5
5
5
5
5
5
5
VOUT (V)
3.3
2.5
1.8
1.2
3.3
2.5
1.8
1.2
2.5
1.8
1.2
0.8
Maximum Load (A)
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
L (μH)
6.8
6.8
6.8
4.7
3.3
3.3
3.3
2.2
1.8
1.8
1.2
1.0
Rev. 0 | Page 32 of 40
COUT (μF)
69 (47 + 22)
100
147 (100 + 47)
200 (2 × 100 )
47
57 (47 + 10)
69 (47 + 22)
100
32 (22 + 10)
44 (2 × 22)
57 (47 + 10)
100
RCOMP (kΩ)
20
22
22
20
27
24
22
20
27
27
24
27
CCOMP (pF)
2400
2400
2400
2400
1000
1100
1100
1200
470
470
510
470
ADP2114
APPLICATION CIRCUITS
VIN = 5V
10Ω
1µF
100kΩ
100kΩ
VIN4
22µF
EN1
VIN1
VDD
EN2
VIN2
VIN5
VOUT2 = 1.8V, 2A
3.3µH
SW3
ADP2114
SW4
47µF
47µF
PGND2
PGND4
SYNC
SW2
PGND1
PGND3
FB1
FB2
V2SET
15kΩ
SW1
PGOOD1
3.3µH VOUT1 = 3.3V, 2A
V1SET
47kΩ
22kΩ
COMP2
SS2
10nF
1100pF
FREQ
OPCFG
SCFG
GND
SYNC/CLKOUT
COMP1
SS1
10nF
27kΩ
1000pF
8.2kΩ
08143-079
22µF
VIN3
PGOOD1
VIN6
PGOOD2
PGOOD2
22µF
fSW = 600kHz
Figure 79. Application Circuit for 2 A/2 A Outputs
VIN = 5V
PGOOD2
V2SET
PGOOD1
VIN4
VIN5
VIN2
SW3
VIN3
ADP2114
SW1
4.7kΩ
PGOOD
VOUT = 1.2V, 4A
47µF
FB1
FB2
10µF
1.2µH
SW2
SW4
47µF
V1SET
VIN1
VIN6
1.2µH
VDD
4.7kΩ
SCFG
1µF
22µF
PGND1
PGND3
PGND2
PGND4
COMP1
COMP2
12kΩ
OPCFG
GND
FREQ
SS1
SS2
EN1
EN2
SYNC/CLKOUT
22nF
VIN
27kΩ 4.7kΩ
1000pF
fSW =
1.2MHz
Figure 80. Application Circuit for a Single 4 A Output
Rev. 0 | Page 33 of 40
08143-080
10µF
100kΩ
10Ω
ADP2114
VIN = 5V
10Ω
1µF
100kΩ
VDD
EN2
VIN4
22µF
EN1
VIN1
SCFG
100kΩ
VIN2
VIN5
VIN3
PGOOD1
VIN6
PGOOD2
PGOOD2
VOUT2 = 3.3V, 1A
6.8µH
SW3
SW4
CLKOUT
47µF
100µF
PGND2
PGND4
47kΩ
VOUT1 = 1.8V, 3A
PGND1
PGND3
47µF
PGOOD1
6.8µH
SW2
FB1
FB2
V2SET
V1SET
15kΩ
COMP1
SS1
22kΩ
10nF
2.4nF
2.4nF
08143-081
8.2kΩ
10nF
FREQ
20kΩ
OPCFG
SYNC/CLKOUT
COMP2
SS2
GND
22µF
SW1
ADP2114
22µF
fSW = 300kHz
Figure 81. Application Circuit for 3 A/1 A Outputs
VIN = 3.3V
10Ω
1µF
100kΩ
VIN2
VIN5
VOUT2 = 1.4V, 2A
SW3
1µH
12.1kΩ 16.2kΩ
ADP2114
SW4
1µH
OPCFG
SYNC/CLKOUT COMP1
COMP2
SS1
SS2
82kΩ
10nF
390pF
fSW = 1.2MHz
Figure 82. Application Circuit for Adjustable Outputs
Rev. 0 | Page 34 of 40
100µF
33kΩ
4.7kΩ
560pF
10nF
V1SET
SCFG
22kΩ
SW2
FB1
FB2
V2SET
FREQ
SYNC
VOUT1 = 1.0V, 2A
SW1
PGND2
PGND4
82kΩ
PGOOD1
PGND1
PGND3
27kΩ
47µF
VIN3
PGOOD1
VIN6
PGOOD2
PGOOD2
22µF
08143-082
VIN4
12.1kΩ 8.06kΩ
22µF
EN1
VIN1
VDD
EN2
GND
100kΩ
ADP2114
POWER DISSIPATION, THERMAL CONSIDERATIONS
Power dissipated by the ADP2114 dual switching regulator is a
major factor that affects the efficiency of the two dc-to-dc
converters. The efficiency is given by
The power dissipated by the regulator increases the die junction
temperature, TJ, above the ambient temperature, TA.
The power loss of the step-down dc-to-dc converter is
approximated by
TJ = TA + TR
(22)
where:
PD is the power dissipation on the ADP2114.
PL is the inductor power losses.
(23)
The ADP2114 power dissipation, PD, includes the power switch
conductive losses, the switch losses, and the transition losses of
each channel.
The power switch conductive losses are due to the output current,
IOUT, flowing through the PMOSFET and the NMOSET power
switches that have internal resistance, RDSON. The amount of
conductive power loss is found by
(24)
where the duty-cycle, D, = VOUT/VIN.
Switching losses are associated with the current drawn by the
driver to turn on and turn off the power devices at the switching
frequency. The amount of switching power loss is given by
PSW = (CGATE-P + CGATE-N) × VIN2 × fSW
where:
CGATE-P is the PMOSFET gate capacitance.
CGATE-N is the NMOSFET gate capacitance.
where the temperature rise, TR, is proportional to the power
dissipation in the package, PD.
TR = θJA × PD
where:
IOUT is the dc load current.
DCRL is the inductor series resistance.
PCOND = [RDSON-P × D + RDSON-N × (1 − D)] × IOUT2
(27)
The proportionality coefficient is defined as the thermal resistance
from the junction of the die to the ambient temperature.
The inductor losses are estimated (without core losses) by
PL ≅ IOUT2 × DCRL
(26)
where tRISE and tFALL are the rise time and the fall time of the
switching node, SW. In the ADP2114, the rise and fall times of
the switching node are in the order of 5 ns.
where:
PIN is the input power.
POUT is the output power.
Power loss is given by PLOSS = PIN − POUT.
PLOSS = PD + PL
PTRAN = VIN × IOUT × (tRISE + tFALL) × fSW
(21)
(25)
(28)
where θJA is the junction-ambient thermal resistance (34°C/W
for the JEDEC 1S2P board, see Table 2).
When designing an application for a particular ambient
temperature range, calculate the expected ADP2114 power
dissipation (PD) due to conductive, switching, and transition
losses of both channels by using Equation 24, Equation 25,
and Equation 26 and estimate the temperature rise by using
Equation 27 and Equation 28. The reliable operation of the
two converters can be achieved only if the estimated die junction
temperature of the ADP2114 (Equation 27) is less than 125°C.
Therefore, at higher ambient temperatures, reduce the power
dissipation of the system. Figure 83 provides the power derating
for the elevated ambient temperature at different air flow
conditions. The area below the curves is the safe operation area
for ADP2114 dual regulators.
2.2
2.0
1.8
AIR VELOCITY = 500 LFM
AIR VELOCITY = 200 LFM
1.6
1.4
1.2
1.0 AIR VELOCITY = 0 LFM
0.8
0.6
0.4
0.2
0
70
85
100
115
AMBIENT TEMPERATURE (°C)
Figure 83. Power Dissipation Derating (JEDEC 1S2P Board)
Rev. 0 | Page 35 of 40
08143-083
POUT
× 100%
PIN
MAXIMUM POWER DISSIPATION (W)
Efficiency =
Transition losses occur because the P-channel power MOSFET
cannot be turned on or off instantaneously. The amount of
transition loss is calculated by
ADP2114
CIRCUIT BOARD LAYOUT RECOMMENDATIONS
•
•
•
•
•
•
Use separate analog and power ground planes. Connect the
ground reference of sensitive analog circuitry, such as output
voltage divider components, to analog ground. In addition,
connect the ground references of power components, such as
input and output capacitors, to power ground. Connect
both ground planes to the exposed pad of the ADP2114.
Place the input capacitor of each channel as close to the
VINx pins as possible and connect the other end to the
closest power ground plane.
For low noise and better transient performance, a filter is
recommended between VINx and VDD. Place a 1 μF, 10 Ω
low-pass input filter between the VDD pin and the VINx
pins, as close to the GND pin as possible.
Ensure that the high current loop traces are as short and as
wide as possible. Make the high current path from CIN
through L, COUT, and the power ground plane back to CIN as
short as possible. To accomplish this, ensure that the input and
output capacitors share a common power ground plane. In
addition, make the high current path from the PGNDx pin
through L and COUT back to the power ground plane as
short as possible. To do this, ensure that the PGNDx pin of
the ADP2114 is tied to the PGND plane as close as possible
to the input and output capacitors (see Figure 84).
Connect the ADP2114 exposed pad to a large copper plane
to maximize its power dissipation capability. Thermal
conductivity can be obtained using the method described
in JEDEC specification JESD51-7.
Rev. 0 | Page 36 of 40
Place the feedback resistor divider network as close as
possible to the FBx pin to prevent noise pickup. Try to
minimize the length of the trace connecting the top of the
feedback resistor divider to the output while keeping away
from the high current traces and the switch node, SWx, that
can lead to noise pickup. To reduce noise pickup, place an
analog ground plane on either side of the FBx trace and
make it as small as possible to reduce the parasitic
capacitance pickup.
VIN
1µF
10Ω
GND
GND
VDD
VINx
CIN
ADP2114
L
VOUT
SWx
COUT
LOAD
PGNDx
FBx
08143-084
Good circuit board layout is essential in obtaining the best
performance from each channel of the ADP2114. Poor circuit
layout degrades the output ripple and regulation, as well as the
EMI and electromagnetic compatibility performance. For
optimum layout, refer to the following guidelines:
Figure 84. High Current Traces in the PCB Circuit
ADP2114
OUTLINE DIMENSIONS
0.60 MAX
5.00
BSC SQ
0.60 MAX
PIN 1
INDICATOR
0.50
BSC
4.75
BSC SQ
0.50
0.40
0.30
17
16
0.30
0.23
0.18
9
8
0.25 MIN
3.50 REF
0.05 MAX
0.02 NOM
SEATING
PLANE
3.25
3.10 SQ
2.95
EXPOSED
PAD
(BOTTOM VIEW)
0.80 MAX
0.65 TYP
12° MAX
1
0.20 REF
COPLANARITY
0.08
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
COMPLIANT TO JEDEC STANDARDS MO-220-VHHD-2
011708-A
TOP
VIEW
1.00
0.85
0.80
PIN 1
INDICATOR
32
25
24
Figure 85. 32-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
5 mm × 5 mm Body, Very Thin Quad
(CP-32-2)
Dimensions shown in millimeters
ORDERING GUIDE
Model
ADP2114ACPZ-R7 2
ADP2114-2PH-EVALZ2
Temperature Range 1
−40°C to +85°C
ADP2114-EVALZ2
1
2
Package Description
32-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
Single output, dual-phase interleaved, 1.2 V at 4 A,
1.2 MHz switching frequency, forced PWM
Dual output, 3.3 V at 2 A and 1.8 V at 2 A, 600 kHz
switching frequency, pulse skip enabled
Operating junction temperature is −40°C to +125°C.
Z = RoHS Compliant Part.
Rev. 0 | Page 37 of 40
Package Option
CP-32-2
Ordering Quantity
1,500
ADP2114
NOTES
Rev. 0 | Page 38 of 40
ADP2114
NOTES
Rev. 0 | Page 39 of 40
ADP2114
NOTES
©2009 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D08143-0-7/09(0)
Rev. 0 | Page 40 of 40