Series AMEGR30-KZ-C1 up to1000mA | AC-DC LED driver FEATURES: • • • • AC-DC Constant Current LED Driver Universal Input: 90-264VAC, 47-63Hz Short circuit protection RoHS compliant • • • • Waterproof IP67 Over current protection Over voltage protection Power Factor Correction Models Single output Model Max Output Power (W) * Output Voltage Range (V) Output Current (mA) Input Voltage (VAC/Hz) Efficiency (%) AMEGR30-30100KZ-C1 30.0 15-30 925 ±75 90-264/ 47-63 85 * Exceeding the maximum output power will permanently damage the converter NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. Input Specifications Parameters Conditions Typical 115V 230V 230V 115V 230V 90-264VAC 10 20 0.25 0.2 0.1 2.5 Voltage range Inrush current <2ms Leakage current AC current No-load consumption External fuse Power Factor Maximum Units VAC A mA A W 250V/1.5A 0.9 Output Specifications Parameters Current accuracy Line regulation Load regulation Ripple & Noise Hold-up time (min) Conditions Typical Maximum Units LL-HL 0% to 100% load 20MHz Bandwidth 100% load ±10 ±5 ±10 150 4 8 % % % mV p-p ms Conditions Typical Maximum Units 5mA/60Sec 3000 1500 >50 3750 VAC VAC MΩ Conditions Typical Maximum Units Isolation Specifications Parameters Tested I/O voltage Input FG Isolation resistance General Specifications Parameters Switching frequency Over current protection Over voltage protection Short circuit protection Operating temperature Maximum case temperature Storage temperature * Temperature coefficient Cooling www.aimtec.com F 052.1e R1.D 100 115 Zener Diode clamp Continuous, Auto recovery -30 to +55 KHz % o 90 -40 to +80 0.05 Free air convection Tel: +1 514 620 2722 1 of 2 C C o C % / oC o Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMEGR30-KZ-C1 up to1000mA | AC-DC LED driver General Specifications (continued) Parameters Conditions Humidity Case material Potting Wires Weight Dimensions (L X H X W) MTBF Typical Maximum Units 95 % RH Aluminum White epoxy (IP67 rated) UL1015 18AWG *20CM 420 8.66 x 1.30 x 0.87inches 220.00 x 33.00 x 22.00mm 50,000 hrs (MIL-HDBK-217 F at +25 oC) g * NOTE: Converters do not have Over Temperature Protection and will be damaged if their maximum case temperature is exceeded. Safety Specifications Parameters Agency approvals Standards CE GB195110.1-2004/IEC61347-1:2003, EN55015, EN61000, EN61547 21.20 (0.84) 12.80 (0.50) 21.70 (0.85) 4.80 (0.19) 35.00 (1.38) Dimensions NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com. www.aimtec.com F 052.1e R1.D Tel: +1 514 620 2722 2 of 2 Toll free: + 1 888 9 AIMTEC (924 6832) North America only