BAT54CLT1 Preferred Device Dual Series Schottky Barrier Diodes These Schottky barrier diodes are designed for high speed switching applications, circuit protection, and voltage clamping. Extremely low forward voltage reduces conduction loss. Miniature surface mount package is excellent for hand held and portable applications where space is limited. http://onsemi.com 30 VOLT DUAL COMMON CATHODE SCHOTTKY BARRIER DIODES • Extremely Fast Switching Speed • Low Forward Voltage - 0.35 Volts (Typ) @ IF = 10 mAdc 1 ANODE 2 ANODE 3 CATHODE MARKING DIAGRAM MAXIMUM RATINGS (TJ = 125°C unless otherwise noted) Symbol Value Unit Reverse Voltage VR 30 Volts Forward Power Dissipation @ TA = 25°C Derate above 25°C PF 225 1.8 mW mW/°C Rating 3 3 5C Forward Current (DC) IF 200 Max mA Junction Temperature TJ 125 Max °C Storage Temperature Range Tstg - 55 to +150 °C 1 1 2 2 (TO-236) SOT-23 CASE 318-08 STYLE 9 ORDERING INFORMATION Device BAT54CLT1 Package Shipping SOT-23 3000/Tape & Reel Preferred devices are recommended choices for future use and best overall value. Semiconductor Components Industries, LLC, 2003 June, 2003 - Rev. 0 1 Publication Order Number: BAT54SLT1/D BAT54CLT1 ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise noted) (EACH DIODE) Characteristic Symbol Min Typ Max Unit V(BR)R 30 - - Volts Total Capacitance (VR = 1.0 V, f = 1.0 MHz) CT - 7.6 10 pF Reverse Leakage (VR = 25 V) IR - 0.5 2.0 µAdc Forward Voltage (IF = 0.1 mAdc) VF - 0.22 0.24 Vdc Forward Voltage (IF = 30 mAdc) VF - 0.41 0.5 Vdc Forward Voltage (IF = 100 mAdc) VF - 0.52 0.8 Vdc Reverse Recovery Time (IF = IR = 10 mAdc, IR(REC) = 1.0 mAdc, Figure 1) trr - - 5.0 ns Forward Voltage (IF = 1.0 mAdc) VF - 0.29 0.32 Vdc Forward Voltage (IF = 10 mAdc) VF - 0.35 0.40 Vdc Forward Current (DC) IF - - 200 mAdc Repetitive Peak Forward Current IFRM - - 300 mAdc Non-Repetitive Peak Forward Current (t < 1.0 s) IFSM - - 600 mAdc Reverse Breakdown Voltage (IR = 10 µA) http://onsemi.com 2 BAT54CLT1 820 Ω +10 V 2k 0.1 µF IF 100 µH tr tp IF T 10% 0.1 µF trr T DUT 50 Ω OUTPUT PULSE GENERATOR 50 Ω INPUT SAMPLING OSCILLOSCOPE 90% iR(REC) = 1 mA IR VR OUTPUT PULSE (IF = IR = 10 mA; measured at iR(REC) = 1 mA) INPUT SIGNAL Notes: 1. A 2.0 kΩ variable resistor adjusted for a Forward Current (IF) of 10 mA. Notes: 2. Input pulse is adjusted so IR(peak) is equal to 10 mA. Notes: 3. tp » trr Figure 1. Recovery Time Equivalent Test Circuit 100 1000 TA = 150°C IR, REVERSE CURRENT (µA) 85°C 10 1 50°C 1.0 25°C 0.1 0.0 - 40°C - 55°C 100 TA = 125°C 10 1.0 TA = 85°C 0.1 0.01 TA = 25°C 0.001 0.2 0.3 0.4 0.1 0.5 VF, FORWARD VOLTAGE (VOLTS) 0 0.6 5 15 25 10 20 VR, REVERSE VOLTAGE (VOLTS) Figure 2. Forward Voltage Figure 3. Leakage Current 14 CT, TOTAL CAPACITANCE (pF) IF, FORWARD CURRENT (mA) 1 25°C 12 10 8 6 4 2 0 0 5 10 15 20 VR, REVERSE VOLTAGE (VOLTS) Figure 4. Total Capacitance http://onsemi.com 3 25 30 30 BAT54CLT1 INFORMATION FOR USING THE SOT-23 SURFACE MOUNT PACKAGE MINIMUM RECOMMENDED FOOTPRINT FOR SURFACE MOUNTED APPLICATIONS Surface mount board layout is a critical portion of the total design. The footprint for the semiconductor packages must be the correct size to insure proper solder connection interface between the board and the package. With the correct pad geometry, the packages will self align when subjected to a solder reflow process. 0.037 0.95 0.037 0.95 0.079 2.0 0.035 0.9 0.031 0.8 inches mm SOT-23 SOT-23 POWER DISSIPATION SOLDERING PRECAUTIONS The power dissipation of the SOT-23 is a function of the pad size. This can vary from the minimum pad size for soldering to a pad size given for maximum power dissipation. Power dissipation for a surface mount device is determined by TJ(max), the maximum rated junction temperature of the die, RθJA, the thermal resistance from the device junction to ambient, and the operating temperature, TA. Using the values provided on the data sheet for the SOT-23 package, PD can be calculated as follows: PD = The melting temperature of solder is higher than the rated temperature of the device. When the entire device is heated to a high temperature, failure to complete soldering within a short time could result in device failure. Therefore, the following items should always be observed in order to minimize the thermal stress to which the devices are subjected. • Always preheat the device. • The delta temperature between the preheat and soldering should be 100°C or less.* • When preheating and soldering, the temperature of the leads and the case must not exceed the maximum temperature ratings as shown on the data sheet. When using infrared heating with the reflow soldering method, the difference shall be a maximum of 10°C. • The soldering temperature and time shall not exceed 260°C for more than 10 seconds. • When shifting from preheating to soldering, the maximum temperature gradient shall be 5°C or less. • After soldering has been completed, the device should be allowed to cool naturally for at least three minutes. Gradual cooling should be used as the use of forced cooling will increase the temperature gradient and result in latent failure due to mechanical stress. • Mechanical stress or shock should not be applied during cooling. TJ(max) - TA RθJA The values for the equation are found in the maximum ratings table on the data sheet. Substituting these values into the equation for an ambient temperature TA of 25°C, one can calculate the power dissipation of the device which in this case is 225 milliwatts. PD = 150°C - 25°C 556°C/W = 225 milliwatts The 556°C/W for the SOT-23 package assumes the use of the recommended footprint on a glass epoxy printed circuit board to achieve a power dissipation of 225 milliwatts. There are other alternatives to achieving higher power dissipation from the SOT-23 package. Another alternative would be to use a ceramic substrate or an aluminum core board such as Thermal Clad. Using a board material such as Thermal Clad, an aluminum core board, the power dissipation can be doubled using the same footprint. * Soldering a device without preheating can cause excessive thermal shock and stress which can result in damage to the device. http://onsemi.com 4 BAT54CLT1 PACKAGE DIMENSIONS SOT-23 (TO-236) PLASTIC PACKAGE CASE 318-08 ISSUE AH NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. 4. 318−03 AND −07 OBSOLETE, NEW STANDARD 318−08. A L 3 1 V B S 2 G C D H J K DIM A B C D G H J K L S V INCHES MIN MAX 0.1102 0.1197 0.0472 0.0551 0.0350 0.0440 0.0150 0.0200 0.0701 0.0807 0.0005 0.0040 0.0034 0.0070 0.0140 0.0285 0.0350 0.0401 0.0830 0.1039 0.0177 0.0236 STYLE 9: PIN 1. ANODE 2. ANODE 3. CATHODE http://onsemi.com 5 MILLIMETERS MIN MAX 2.80 3.04 1.20 1.40 0.89 1.11 0.37 0.50 1.78 2.04 0.013 0.100 0.085 0.177 0.35 0.69 0.89 1.02 2.10 2.64 0.45 0.60 BAT54CLT1 SENSEFET is a trademark of Semiconductor Components Industries, LLC. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. PUBLICATION ORDERING INFORMATION Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: [email protected] JAPAN: ON Semiconductor, Japan Customer Focus Center 2-9-1 Kamimeguro, Meguro-ku, Tokyo, Japan 153-0051 Phone: 81-3-5773-3850 ON Semiconductor Website: http://onsemi.com For additional information, please contact your local Sales Representative. N. American Technical Support: 800-282-9855 Toll Free USA/Canada http://onsemi.com 6 BAT54CLT1/D