IRF IR21091PBF

Data Sheet No. PD60191 revD
IR21091(S) & (PbF)
HALF-BRIDGE DRIVER
Product Summary
Features
•
•
•
•
•
•
•
•
•
•
•
•
Floating channel designed for bootstrap operation
Fully operational to +600V
Tolerant to negative transient voltage
dV/dt immune
Gate drive supply range from 10 to 20V
Undervoltage lockout for both channels
3.3V, 5V and 15V input logic compatible
Cross-conduction prevention logic
Matched propagation delay for both channels
High side output in phase with IN input
Logic and power ground +/- 5V offset.
Internal 500ns dead-time, and programmable
up to 5us with one external RDT resistor
Lower di/dt gate driver for better noise immunity
The dual function DT/SD pin input turns off both
channels.
Available in Lead-Free
VOFFSET
IO+/VOUT
ton/off (typ.)
Dead time
600V max.
120 mA / 250 mA
10 - 20V
680 & 170 ns
500 ns
(programmable up to 5uS)
Packages
Description
The IR21091(S) are high voltage, high speed power
MOSFET and IGBT drivers with dependant high and
8 Lead SOIC
8 Lead PDIP
low side referenced output channels. Proprietary HVIC
and latch immune CMOS technologies enable ruggedized monolithic construction. The logic input is compatible with standard CMOS or LSTTL output, down to
3.3V logic. The output drivers feature a high pulse current buffer stage designed for minimum driver crossconduction. The floating channel can be used to drive an N-channel power MOSFET or IGBT in the high
side configuration which operates up to 600 volts.
Typical Connection
up to 600V
VCC
VCC
VB
IN
IN
HO
SD
DT/SD
VS
COM
LO
TO
LOAD
IR21091(S)
(Refer to Lead Assignments for correct configuration). This/These diagram(s) show electrical connections
only. Please refer to our Application Notes and DesignTips for proper circuit board layout.
www.irf.com
1
IR21091(S) & (PbF)
Absolute Maximum Ratings
Absolute maximum ratings indicate sustained limits beyond which damage to the device may occur. All voltage parameters are absolute voltages referenced to COM. The thermal resistance and power dissipation ratings are measured
under board mounted and still air conditions.
Symbol
Definition
VB
High side floating absolute voltage
VS
Min.
Max.
-0.3
625
Units
High side floating supply offset voltage
VB - 25
VB + 0.3
VHO
High side floating output voltage
VS - 0.3
VB + 0.3
VCC
Low side and logic fixed supply voltage
-0.3
25
VLO
Low side output voltage
-0.3
VCC + 0.3
Programmable dead-time and shut-down pin voltage
VSS - 0.3
VCC + 0.3
Logic input voltage
VSS - 0.3
VCC + 0.3
DT/SD
VIN
dVS/dt
PD
Rth JA
Allowable offset supply voltage transient
Package power dissipation @ TA ≤ +25°C
Thermal resistance, junction to ambient
—
50
(8 Lead PDIP)
—
1.0
(8 Lead SOIC)
—
0.625
(8 Lead PDIP)
—
125
(8 Lead SOIC)
—
200
TJ
Junction temperature
—
150
TS
Storage temperature
-50
150
TL
Lead temperature (soldering, 10 seconds)
—
300
V
V/ns
W
°C/W
°C
Recommended Operating Conditions
The input/output logic timing diagram is shown in figure 1. For proper operation the device should be used within the
recommended conditions. The VS offset rating are tested with all supplies biased at 15V differential.
Symbol
Definition
VB
High side floating supply absolute voltage
VS
High side floating supply offset voltage
Min.
Max.
VS + 10
VS + 20
Note 1
600
VB
VHO
High side floating output voltage
VS
VCC
Low side and logic fixed supply voltage
10
20
VLO
Low side output voltage
0
VCC
VIN
DT/SD
TA
Logic input voltage
VSS
VCC
Programmable dead-time and shut-down pin voltage
VSS
VCC
Ambient temperature
-40
125
Units
V
°C
Note 1: Logic operational for VS of -5 to +600V. Logic state held for VS of -5V to -VBS. (Please refer to the Design Tip
DT97-3 for more details).
2
www.irf.com
IR21091(S) & (PbF)
Dynamic Electrical Characteristics
VBIAS (VCC, VBS) = 15V, CL = 1000 pF, TA = 25°C, DT = VSS unless otherwise specified.
Symbol
Definition
Min.
Typ.
—
750
950
VS = 0V
Turn-off propagation delay
—
200
280
VS = 0V or 600V
Delay matching, HS & LS turn-on/off
—
0
70
tr
Turn-on rise time
—
150
220
tf
DT
Turn-off fall time
—
Deadtime: LO turn-off to HO turn-on(DTLO-HO) &
HO turn-off to LO turn-on (DTHO-LO)
400
4
Deadtime matching = DTLO - HO - DTHO-LO
ton
Turn-on propagation delay
toff
MT
MDT
tsd
Shut down propagation delay
Max. Units Test Conditions
nsec
50
80
540
5
680
6
usec
—
—
0
0
60
600
nsec
215
—
615
VS = 0V
VS = 0V
RDT= 0
RDT = 200k
RDT=0
RDT = 200k
Static Electrical Characteristics
VBIAS (VCC, VBS) = 15V, DT= VSS and TA = 25°C unless otherwise specified. The VIL , VIH and IIN parameters are
referenced to VSS /COM and are applicable to the respective input leads: IN and DT. The VO, IO and Ron parameters are
referenced to COM and are applicable to the respective output leads: HO and LO.
Symbol
Definition
Min. Typ. Max. Units Test Conditions
VIH
Logic “1” input voltage for HO & logic “0” for LO
2.9
—
—
VCC = 10V to 20V
VIL
Logic “0” input voltage for HO & logic “1” for LO
—
—
0.8
VCC = 10V to 20V
VSD,TH
DT/SD pin shutdown input threshold
11.5
13
14.5
VOH
High level output voltage, VBIAS - VO
—
0.8
1.4
VOL
Low level output voltage, VO
—
0.3
0.6
ILK
Offset supply leakage current
—
—
50
IQBS
Quiescent VBS supply current
20
60
150
IQCC
Quiescent VCC supply current
0.4
1.0
1.6
IIN+
Logic “1” input bias current
—
5
20
IIN-
Logic “0” input bias current
—
1
2
VCC and VBS supply undervoltage positive going
8.0
8.9
9.8
7.4
8.2
9.0
V
IO = 20 mA
IO = 20 mA
µA
VB = VS = 600V
VIN = 0V or 5V
mA
VIN = 0V or 5V
RDT = 0
VCCUV+
VBSUV+
VCCUV-
µA
IN = 5V, SD = 0V
IN = 0V, SD = 5V
threshold
VCC and VBS supply undervoltage negative going
VBSUV-
threshold
VCCUVH
Hysteresis
0.3
0.7
—
IO+
Output high short circuit pulsed vurrent
120
200
—
IO-
Output low short circuit pulsed current
V
VBSUVH
www.irf.com
250
350
—
mA
VO = 0V, PW ≤ 10 µs
VO =15V,PW ≤ 10 µs
3
IR21091(S) & (PbF)
Functional Block Diagrams
VB
UV
DETECT
IR21091(S)
HO
R
VSS/COM
LEVEL
SHIFT
IN
DT/SD
HV
LEVEL
SHIFTER
R
PULSE
FILTER
S
VS
PULSE
GENERATOR
VCC
DEADTIME
UV
DETECT
VSS/COM
LEVEL
SHIFT
4
Q
DELAY
LO
COM
www.irf.com
IR21091(S) & (PbF)
Lead Definitions
Symbol Description
IN
Logic input for high and low side gate driver outputs (HO and LO), in phase with HO
DT/SD
Programmable dead-time lead, referenced to VSS. Disables input/output logic when tied to VCC
VB
High side floating supply
HO
High side gate drive output
VS
High side floating supply return
VCC
Low side and logic fixed supply
LO
Low side gate drive output
COM
Low side return
Lead Assignments
1
VCC
VB
8
1
2
IN
HO
7
3
DT/SD
VS
6
COM
LO
4
www.irf.com
5
VCC
VB
8
2
IN
HO
7
3
DT/SD
VS
6
COM
LO
5
4
8 Lead PDIP
8 Lead SOIC
IR21091
IR21091(S)
5
IR21091(S) & (PbF)
Case Outlines
01-6014
01-3003 01 (MS-001AB)
8 Lead PDIP
D
DIM
B
5
A
F OOT PRINT
6
8
7
6
5
H
E
0.25 [.010]
1
2
3
A
4
6.46 [.255]
MIN
.0532
.0688
1.35
1.75
A1 .0040
3X 1.27 [.050]
8X 1.78 [.070]
e1
MAX
0.25
.0098
0.10
b
.013
.020
0.33
0.51
c
.0075
.0098
0.19
0.25
D
.189
.1968
4.80
5.00
E
.1497
.1574
3.80
4.00
e
.050 BAS IC
e1
6X e
MILLIMETERS
MAX
A
8X 0.72 [.028]
INCHES
MIN
.025 BAS IC
1.27 BAS IC
0.635 BAS IC
H
.2284
.2440
5.80
6.20
K
.0099
.0196
0.25
0.50
L
.016
.050
0.40
1.27
y
0°
8°
0°
8°
K x 45°
A
C
y
0.10 [.004]
8X b
0.25 [.010]
A1
8X L
8X c
7
C A B
4. OUT LINE CONFORMS T O JEDEC OUTLINE MS -012AA.
NOT ES:
1. DIMENS IONING & T OLERANCING PE R ASME Y14.5M-1994.
2. CONT ROLLING DIMENSION: MILLIMET ER
3. DIMENS IONS ARE SHOWN IN MILLIME TE RS [INCHES].
4. OUT LINE CONF ORMS T O JEDEC OUTLINE MS-012AA.
8 Lead SOIC
6
5 DIMENSION DOES NOT INCLUDE MOLD PROT RUS IONS.
MOLD PROTRUSIONS NOT T O E XCEED 0.15 [.006].
6 DIMENSION DOES NOT INCLUDE MOLD PROT RUS IONS.
MOLD PROTRUSIONS NOT T O E XCEED 0.25 [.010].
7 DIMENSION IS T HE LE NGTH OF LEAD FOR SOLDE RING TO
A SUBS TRAT E.
01-6027
01-0021 11 (MS-012AA)
www.irf.com
IR21091(S) & (PbF)
IN(LO)
IN
50%
50%
IN(HO)
DT/SD
ton
toff
tr
HO
90%
LO
HO
LO
Figure 1. Input/Output Timing Diagram
10%
10%
50%
IN
DT/SD
tsd
90%
90%
HO
LO
90%
Figure 2. Switching Time Waveform Definitions
50%
50%
tf
HO
LO
Figure 3. Shutdown Waveform Definitions
DT LO-HO
10%
DT HO-LO
90%
10%
MDT=
DT LO-HO
- DT HO-LO
Figure 4. Deadtime Waveform Definitions
IN (LO)
50%
50%
IN (HO)
LO
HO
10%
MT
MT
90%
LO
HO
Figure 5. Delay Matching Waveform Definitions
www.irf.com
7
IR21091(S) & (PbF)
Basic Part (Non-Lead Free)
Lead-Free Part
8-Lead PDIP IR21091 order IR21091
8-Lead SOIC IR21091S order IR21091S
8-Lead PDIP IR21091 order IR21091PBF
8-Lead SOIC IR21091S order IR21091SPBF
This product has been designed and qualified for the Industrial market.
Qualification Standards can be found on IR’s Website.
Data and specifications subject to change without notice.
IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105
TAC Fax: (310) 252-7903
Visit us at www.irf.com for sales contact information. 7/19/2005
8
www.irf.com