RLAT Report 08-402 090317 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Radiation Lot Acceptance Testing (RLAT) of the RH1013MJ8 Dual Precision Operational Amplifier for Linear Technology Customer: Linear Technology, PO# 51419L RAD Job Number: 08-402 Part Type Tested: Linear Technology RH1013MJ8 Dual Precision Operational Amplifier Commercial Part Number: RH1013MJ8 Traceability Information: Fab # WR0246269, Wafer 8. Information obtained from Linear Technology PO#51419L. Date code marking on the package is 0548A, see Appendix B for a photograph of the device and part markings. Quantity of Units: 12 units total, 5 units for biased irradiation, 5 units for unbiased irradiation (all pins tied to ground) and 2 control units. Serial numbers 1090, 1092, 1093, 1094, and 1095 were biased during irradiation. Serial numbers 1096, 1097, 1098, 1099 and 1100 were unbiased during irradiation (all pins tied to ground). Serial numbers 1106 and 1113 were used as controls. External Traveler: None required Pre-Irradiation Burn-In: Burn-In performed by Linear Devices prior to receipt by RAD. TID Dose Rate and Test Increments: 50krad(Si), 100krad(Si) and 200krad(Si). 68.8rad(Si)/s with test increments at: Pre-Irradiation, 20krad(Si), TID Overtest and Post-Irradiation Anneal: No overtest or anneal. TID Test Standard: MIL-STD-883G, Method 1019.7, Condition A TID Electrical Test Conditions: Pre-irradiation, and within one hour following each radiation exposure. Test Programs: RH1013LT.SRC Hardware: LTS2020 Tester, 2100 Family Board, 0600 Fixture and RH1013 DUT Board Facility and Radiation Source: Radiation Assured Devices Longmire Laboratories, Colorado Springs, CO using the JLSA 81-24 high dose rate Co60 source. Dosimetry performed by CaF TLDs traceable to NIST. RAD’s dosimetry has been audited by DSCC and RAD has been awarded Laboratory Suitability for MIL-STD-750 TM 1019.5. Irradiation and Test Temperature: Ambient, room temperature An ISO 9001:2000 Certified Company 1 RLAT Report 08-402 090317 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 1.0. Overview and Background It is well known that total dose ionizing radiation can cause parametric degradation and ultimately functional failure in electronic devices. The damage occurs via electron-hole pair production, transport and trapping in the dielectric and interface regions. In discrete devices the bulk of the damage is frequently manifested as a reduction in the gain and/or breakdown voltage of the device. The damage will usually anneal with time following the end of the radiation exposure. Due to this annealing, and to ensure a worst-case test condition MIL-STD-883 TM1019.7 calls out a dose rate of 50 to 300rad(Si)/s as Condition A and further specifies that the time from the end of an incremental radiation exposure and electrical testing shall be 1-hour or less and the total time from the end of one incremental irradiation to the beginning of the next incremental radiation step should be 2-hours or less. The work described in this report was performed to meet MIL-STD-883 TM1019.7 Condition A. 2.0. Radiation Test Apparatus The total ionizing dose testing described in this final report was performed using the facilities at Radiation Assured Devices’ Longmire Laboratories in Colorado Springs, CO. The high dose rate total ionizing dose (TID) source is a JLSA 84-21 irradiator modified to provide a panoramic exposure. The Co-60 rods are held in the base of the irradiator heavily shielded by lead, during the radiation exposures the rod is raised by an electronic timer/controller and the exposure is performed in air. The dose rate for this irradiator in this configuration ranges from <1rad(Si)/s to a maximum of approximately 120rad(Si)/s, determined by the distance from the source. For high-dose rate experiments the bias boards are placed in a radial fashion equidistant from the raised Co-60 rods with the distance adjusted to provide the required dose rate. The irradiator calibration is maintained by Radiation Assured Devices Longmire Laboratories using thermoluminescent dosimeters (TLDs)) traceable to the National Institute of Standards and Technology (NIST). Figure 2.1 shows a photograph of the JLSA 81-24 Co-60 irradiator at RAD’s Longmire Laboratory facility. RAD is currently certified by the Defense Supply Center Columbus (DSCC) for Laboratory Suitability under MIL STD 750. Additional details regarding Radiation Assured Devices dosimetry for TM1019 Condition A testing are available in RAD’s report to DSCC entitled: “Dose Rate Mapping of the J.L. Shepherd and Associates Model 81 Irradiator Installed by Radiation Assured Devices” An ISO 9001:2000 Certified Company 2 RLAT Report 08-402 090317 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Figure 2.1. Radiation Assured Devices’ high dose rate Co-60 irradiator. The dose rate is obtained by positioning the device-under-test at a fixed distance from the gamma cell. The dose rate for this irradiator varies from approximately 120rad(Si)/s close to the rods down to 1rad(Si)/s at a distance of approximately 2-feet. An ISO 9001:2000 Certified Company 3 RLAT Report 08-402 090317 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 3.0. Radiation Test Conditions The RH1013 dual operational amplifiers described in this final report were irradiated using a split 15V supply and with all pins tied to ground, that is biased and unbiased. See the TID Bias Table in Appendix A for the full bias circuits. These bias circuits satisfy the requirements of MIL-STD-883G TM1019.7 Section 3.9.3 Bias and Loading Conditions which states “The bias applied to the test devices shall be selected to produce the greatest radiation induced damage or the worst-case damage for the intended application, if known. While maximum voltage is often worst case some bipolar linear device parameters (e.g. input bias current or maximum output load current) exhibit more degradation with 0 V bias.” The devices were irradiated to a maximum total ionizing dose level of 200krad(Si) with incremental readings at 20, 50, 100 and 200krad(Si) for all electrical tests using the ±15V supply and with incremental readings at 20, 50 and 100krad(Si) for all electrical tests using the +5V and 0V supply conditions (See LINEAR TECHNOLOGY CORPORATION RH1013M Dual Precision Operational Amplifier Datasheet Page 3, Note 2). Electrical testing occurred within one hour following the end of each irradiation segment. For intermediate irradiations, the parts were tested and returned to total dose exposure within two hours from the end of the previous radiation increment. The TID bias board was positioned in the Co-60 cell to provide the required minimum of 50rad(Si)/s and was located inside a lead-aluminum enclosure. The lead-aluminum enclosure is required under MIL-STD-883G TM1019.7 Section 3.4 that reads as follows: “Lead/Aluminum (Pb/Al) container. Test specimens shall be enclosed in a Pb/Al container to minimize dose enhancement effects caused by lowenergy, scattered radiation. A minimum of 1.5 mm Pb, surrounding an inner shield of at least 0.7 mm Al, is required. This Pb/Al container produces an approximate charged particle equilibrium for Si and for TLDs such as CaF2. The radiation field intensity shall be measured inside the Pb/Al container (1) initially, (2) when the source is changed, or (3) when the orientation or configuration of the source, container, or test-fixture is changed. This measurement shall be performed by placing a dosimeter (e.g., a TLD) in the device-irradiation container at the approximate test-device position. If it can be demonstrated that low energy scattered radiation is small enough that it will not cause dosimetry errors due to dose enhancement, the Pb/Al container may be omitted”. The final dose rate within the high dose rate lead-aluminum enclosure was determined based on TLD dosimetry measurements (see previous section). The final dose rate for this work was 68.8rad(Si)/s with a precision of ±5%. An ISO 9001:2000 Certified Company 4 RLAT Report 08-402 090317 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 4.0. Tested Parameters During the radiation lot acceptance testing the pre- and post-irradiation electrical parameters measured were: ±15V Tests 1. Positive Supply Current (ICC+) 2. Negative Supply Current (IEE-) 3. Input Offset Voltage (VOS Channel A and B) 4. Input Offset Current (IOS Channel A and B) 5. + Input Bias Current (IB+ Channel A and B) 6. - Input Bias Current (IB- Channel A and B) 7. Common Mode Rejection Ratio (CMRR Channel A and B) 8. Power Supply Rejection Ratio (PSRR Channel A and B) 9. Large Signal Voltage Gain (AVOL Channel A and B) 10. Positive Output Voltage Swing, No Load (VOUT Channel A and B) 11. Positive Output Voltage Swing, 600Ω (VOUT Channel A and B) 12. Negative Output Voltage Swing, No Load (VOUT Channel A and B) 13. Negative Output Voltage Swing, 600Ω (VOUT Channel A and B) 14. Positive Slew Rate (SlewRate+ Channel A and B) 15. Negative Slew Rate (SlewRate- Channel A and B) +5V Tests 16. Positive Supply Current (ICC+2) 17. Negative Supply Current (IEE-2) 18. Input Offset Voltage (VOS Channel A and B) 19. Input Offset Current (IOS Channel A and B) 20. + Input Bias Current (IB+ Channel A and B) 21. - Input Bias Current (IB- Channel A and B) 22. Output Voltage High, No Load (VOUT Channel A and B) 23. Output Voltage High, 600Ω (VOUT Channel A and B) 24. Output Voltage Low, No Load (VOUT Channel A and B) 25. Output Voltage Low, 600Ω (VOUT Channel A and B) 26. Output Voltage Low, 1mA (VOUT Channel A and B) The parametric data was obtained as read and record and all the raw data plus an attributes summary are contained in a separate Excel file. The attributes data contains the average, standard deviation and the average with the KTL values applied. The KTL value used is 2.742 per MIL HDBK 814 using one sided tolerance limits of 90/90 and a 5-piece sample size. Note that the following criteria must be met for a device to pass the RLAT: following the radiation exposure each of the 5 pieces shall pass the An ISO 9001:2000 Certified Company 5 RLAT Report 08-402 090317 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 specification value and the average value for the ten-piece sample must pass the specification value when the KTL limits are applied. If either of these conditions is not satisfied following the radiation exposure, then the lot could be logged as a failure. 5.0. Total Ionizing Dose Test Results The RH1013 operational amplifiers passed the RLAT to the maximum tested level of 200krad(Si) without any significant degradation to most of the measured parameters. As seen in the data plots, several parameters suffered measurable radiation-induced degradation, however in no case was it sufficient to cause the parameters to go out of specification even after application of the KTL statistics. Figures 5.1 and 5.44 show plots of all the measured parameters versus total ionizing dose while Tables 5.1 – 5.44 show the corresponding raw data for each of these parameters. Note that Large Signal Voltage Gain data is presented in both V/mV and dB units. The V/mV plots are in Figures 5.15 and 5.16 with the corresponding raw data in Tables 5.15 and 5.16. The dB plots and raw data are in Appendix D. In the data plots the solid diamonds are the average of the measured data points for the sample irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the units irradiated with all pins tied to ground. The black lines (solid or dashed) are the average of the data points after application of the KTL statistics on the sample irradiated in the biased condition while the shaded lines (solid or dashed) are the average of the data points after application of the KTL statistics on the sample irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or postirradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. The control units, as expected, show no significant changes to any of the parameters. Therefore we can conclude that the electrical testing remained in control throughout the duration of the tests and the minor observed degradation was due to the radiation exposure. An ISO 9001:2000 Certified Company 6 RLAT Report 08-402 090317 R1.1 Average Biased Average Un-Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (+KTL) Biased 1.20E-03 Positive Supply Current (ICC+) (A) 1.10E-03 1.00E-03 9.00E-04 8.00E-04 7.00E-04 6.00E-04 5.00E-04 0 50 100 150 Total Dose (krad(Si)) Figure 5.1. Plot of positive supply current (±15V) versus total dose. The data shows a general improvement with total dose. The solid diamonds are the average of the measured data points for the sample irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the units irradiated with all pins tied to ground. The black lines (solid or dashed) are the average of the data points after application of the KTL statistics on the sample irradiated in the biased condition while the shaded lines (solid or dashed) are the average of the data points after application of the KTL statistics on the sample irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2000 Certified Company 7 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 08-402 090317 R1.1 Table 5.1. Raw data of the Positive Supply Current @ +/-15V (A) versus total dose, including the statistical analysis, the specification and the status of the testing (pass/fail). Total Dose (krad(Si)) Positive Supply Current (ICC+) (A) Device 1090 1092 1093 1094 1095 1096 1097 1098 1099 1100 1106 1113 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MAX Status 0 7.71E-04 7.93E-04 7.72E-04 7.54E-04 8.05E-04 7.89E-04 7.68E-04 7.66E-04 7.91E-04 7.88E-04 7.70E-04 7.95E-04 20 7.80E-04 8.01E-04 7.81E-04 7.64E-04 8.07E-04 8.10E-04 7.83E-04 7.84E-04 8.03E-04 8.01E-04 7.72E-04 7.94E-04 50 7.59E-04 7.78E-04 7.62E-04 7.37E-04 7.85E-04 7.82E-04 7.55E-04 7.62E-04 7.76E-04 7.72E-04 7.73E-04 7.95E-04 100 7.01E-04 7.22E-04 7.11E-04 6.83E-04 7.33E-04 7.23E-04 6.97E-04 7.16E-04 7.15E-04 7.03E-04 7.73E-04 7.95E-04 200 5.94E-04 6.18E-04 6.11E-04 5.84E-04 6.32E-04 6.17E-04 6.04E-04 6.09E-04 5.95E-04 5.87E-04 7.71E-04 7.91E-04 7.79E-04 2.01E-05 8.34E-04 7.24E-04 7.87E-04 1.74E-05 8.34E-04 7.39E-04 7.64E-04 1.87E-05 8.15E-04 7.13E-04 7.10E-04 1.93E-05 7.63E-04 6.57E-04 6.08E-04 1.91E-05 6.60E-04 5.55E-04 7.80E-04 1.23E-05 8.14E-04 7.47E-04 1.10E-03 PASS 7.96E-04 1.21E-05 8.29E-04 7.63E-04 1.10E-03 PASS 7.69E-04 1.09E-05 7.99E-04 7.40E-04 1.10E-03 PASS 7.11E-04 1.05E-05 7.40E-04 6.82E-04 1.10E-03 PASS 6.02E-04 1.17E-05 6.35E-04 5.70E-04 1.10E-03 PASS An ISO 9001:2000 Certified Company 8 RLAT Report 08-402 090317 R1.1 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (-KTL) Biased Negative Supply Current (IEE-) (A) -5.00E-04 -6.00E-04 -7.00E-04 -8.00E-04 -9.00E-04 -1.00E-03 -1.10E-03 -1.20E-03 0 50 100 150 Total Dose (krad(Si)) Figure 5.2. Plot of Negative Supply Current @ +/-15V (A) versus total dose. The data show a general improvement with total dose. The solid diamonds are the average of the measured data points for the sample irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the units irradiated with all pins tied to ground. The black lines (solid or dashed) are the average of the data points after application of the KTL statistics on the sample irradiated in the biased condition while the shaded lines (solid or dashed) are the average of the data points after application of the KTL statistics on the sample irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2000 Certified Company 9 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 08-402 090317 R1.1 Table 5.2. Raw data for the Negative Supply Current @ +/-15V (A) versus total dose, including the statistical analysis, the specification and the status of the testing (pass/fail). Total Dose (krad(Si)) Negative Supply Current (IEE-) (A) Device 1090 1092 1093 1094 1095 1096 1097 1098 1099 1100 1106 1113 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status 0 -7.71E-04 -7.94E-04 -7.73E-04 -7.53E-04 -8.04E-04 -7.90E-04 -7.68E-04 -7.65E-04 -7.92E-04 -7.88E-04 -7.72E-04 -7.96E-04 20 -7.79E-04 -8.00E-04 -7.83E-04 -7.66E-04 -8.09E-04 -8.11E-04 -7.83E-04 -7.85E-04 -8.04E-04 -8.01E-04 -7.71E-04 -7.96E-04 50 -7.60E-04 -7.79E-04 -7.63E-04 -7.37E-04 -7.85E-04 -7.82E-04 -7.56E-04 -7.63E-04 -7.76E-04 -7.73E-04 -7.74E-04 -7.95E-04 100 -7.03E-04 -7.22E-04 -7.11E-04 -6.83E-04 -7.33E-04 -7.23E-04 -6.98E-04 -7.18E-04 -7.16E-04 -7.05E-04 -7.71E-04 -7.94E-04 200 -5.94E-04 -6.17E-04 -6.12E-04 -5.85E-04 -6.33E-04 -6.19E-04 -6.04E-04 -6.10E-04 -5.97E-04 -5.88E-04 -7.71E-04 -7.94E-04 -7.79E-04 2.02E-05 -7.24E-04 -8.34E-04 -7.87E-04 1.71E-05 -7.40E-04 -8.34E-04 -7.65E-04 1.88E-05 -7.13E-04 -8.16E-04 -7.10E-04 1.90E-05 -6.58E-04 -7.63E-04 -6.08E-04 1.90E-05 -5.56E-04 -6.60E-04 -7.81E-04 1.30E-05 -7.45E-04 -8.16E-04 -1.10E-03 PASS -7.97E-04 1.23E-05 -7.63E-04 -8.30E-04 -1.10E-03 PASS -7.70E-04 1.04E-05 -7.41E-04 -7.99E-04 -1.10E-03 PASS -7.12E-04 1.02E-05 -6.84E-04 -7.40E-04 -1.10E-03 PASS -6.04E-04 1.19E-05 -5.71E-04 -6.36E-04 -1.10E-03 PASS An ISO 9001:2000 Certified Company 10 RLAT Report 08-402 090317 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 1.00E-03 Input Offset Voltage CH A (V) 8.00E-04 6.00E-04 4.00E-04 2.00E-04 0.00E+00 -2.00E-04 -4.00E-04 -6.00E-04 -8.00E-04 -1.00E-03 0 50 100 150 Total Dose (krad(Si)) Figure 5.3. Plot of input offset voltage for channel A @ +/-15V (A) versus total dose. The data show some increase with total dose. The solid diamonds are the average of the measured data points for the sample irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the units irradiated with all pins tied to ground. The black lines (solid or dashed) are the average of the data points after application of the KTL statistics on the sample irradiated in the biased condition while the shaded lines (solid or dashed) are the average of the data points after application of the KTL statistics on the sample irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan An ISO 9001:2000 Certified Company 11 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 08-402 090317 R1.1 Table 5.3. Raw data of input offset voltage for channel A @ +/-15V (A) versus total dose, including the statistical analysis, the specification and the status of the testing (pass/fail). Total Dose (krad(Si)) Input Offset Voltage CH A (V) Device 1090 1092 1093 1094 1095 1096 1097 1098 1099 1100 1106 1113 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status 0 -6.16E-06 2.05E-05 8.64E-05 -4.35E-05 -4.29E-05 6.17E-05 5.42E-05 7.20E-07 -4.38E-05 1.92E-05 1.24E-04 -1.37E-05 20 -1.33E-06 2.44E-05 9.04E-05 -3.39E-05 -4.83E-05 7.49E-05 6.68E-05 1.05E-05 -3.13E-05 2.40E-05 1.27E-04 -1.38E-05 50 1.59E-05 4.60E-05 1.12E-04 -7.48E-06 -2.78E-05 9.85E-05 9.62E-05 3.59E-05 -2.05E-06 5.67E-05 1.29E-04 -1.03E-05 100 5.23E-05 7.69E-05 1.34E-04 4.67E-05 -1.69E-06 1.47E-04 1.58E-04 7.70E-05 6.06E-05 1.20E-04 1.25E-04 -1.16E-05 200 1.25E-04 1.33E-04 1.83E-04 1.42E-04 5.69E-05 2.36E-04 2.78E-04 1.60E-04 1.87E-04 2.61E-04 1.22E-04 -9.90E-06 2.87E-06 5.39E-05 1.51E-04 -1.45E-04 6.25E-06 5.49E-05 1.57E-04 -1.44E-04 2.78E-05 5.46E-05 1.78E-04 -1.22E-04 6.17E-05 4.96E-05 1.98E-04 -7.43E-05 1.28E-04 4.54E-05 2.52E-04 3.24E-06 1.84E-05 4.29E-05 1.36E-04 -9.91E-05 -3.00E-04 PASS 3.00E-04 PASS 2.90E-05 4.34E-05 1.48E-04 -9.00E-05 -4.50E-04 PASS 4.50E-04 PASS 5.71E-05 4.24E-05 1.73E-04 -5.92E-05 -6.00E-04 PASS 6.00E-04 PASS 1.12E-04 4.26E-05 2.29E-04 -4.29E-06 -7.50E-04 PASS 7.50E-04 PASS 2.24E-04 4.97E-05 3.61E-04 8.80E-05 -9.00E-04 PASS 9.00E-04 PASS An ISO 9001:2000 Certified Company 12 RLAT Report 08-402 090317 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 1.00E-03 Input Offset Voltage CH B (V) 8.00E-04 6.00E-04 4.00E-04 2.00E-04 0.00E+00 -2.00E-04 -4.00E-04 -6.00E-04 -8.00E-04 -1.00E-03 0 50 100 150 Total Dose (krad(Si)) Figure 5.4. Plot of input offset voltage for channel B @ +/-15V (A) versus total dose. The data show some increase with total dose. The solid diamonds are the average of the measured data points for the sample irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the units irradiated with all pins tied to ground. The black lines (solid or dashed) are the average of the data points after application of the KTL statistics on the sample irradiated in the biased condition while the shaded lines (solid or dashed) are the average of the data points after application of the KTL statistics on the sample irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2000 Certified Company 13 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 08-402 090317 R1.1 Table 5.4. Raw data of input offset voltage for channel B @ +/-15V (A) versus total dose, including the statistical analysis, the specification and the status of the testing (pass/fail). Total Dose (krad(Si)) Input Offset Voltage CH B (V) Device 1090 1092 1093 1094 1095 1096 1097 1098 1099 1100 1106 1113 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status 0 3.65E-05 -3.26E-06 -7.13E-06 -9.78E-06 -6.43E-05 1.85E-05 8.33E-06 5.19E-06 -6.34E-05 -5.97E-05 1.30E-05 4.83E-06 20 4.13E-05 3.98E-06 -6.88E-06 -3.98E-06 -6.28E-05 3.16E-05 3.10E-05 1.69E-05 -4.25E-05 -4.27E-05 1.21E-05 4.59E-06 50 6.79E-05 1.68E-05 1.45E-06 2.52E-05 -3.40E-05 6.22E-05 6.57E-05 4.00E-05 -1.30E-05 -1.11E-05 1.06E-05 4.59E-06 100 1.08E-04 4.27E-05 3.19E-05 7.05E-05 -1.07E-05 1.24E-04 1.36E-04 9.57E-05 4.60E-05 5.71E-05 1.01E-05 2.05E-06 200 1.82E-04 9.25E-05 7.04E-05 1.70E-04 3.90E-05 2.24E-04 2.69E-04 1.84E-04 1.64E-04 1.98E-04 1.34E-05 4.11E-06 -9.59E-06 3.59E-05 8.88E-05 -1.08E-04 -5.67E-06 3.73E-05 9.66E-05 -1.08E-04 1.55E-05 3.70E-05 1.17E-04 -8.61E-05 4.85E-05 4.43E-05 1.70E-04 -7.29E-05 1.11E-04 6.26E-05 2.82E-04 -6.09E-05 -1.82E-05 3.99E-05 9.11E-05 -1.28E-04 -3.00E-04 PASS 3.00E-04 PASS -1.13E-06 3.83E-05 1.04E-04 -1.06E-04 -4.50E-04 PASS 4.50E-04 PASS 2.87E-05 3.85E-05 1.34E-04 -7.69E-05 -6.00E-04 PASS 6.00E-04 PASS 9.18E-05 3.98E-05 2.01E-04 -1.73E-05 -7.50E-04 PASS 7.50E-04 PASS 2.08E-04 4.04E-05 3.18E-04 9.71E-05 -9.00E-04 PASS 9.00E-04 PASS An ISO 9001:2000 Certified Company 14 RLAT Report 08-402 090317 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 3.00E-08 Input Offset Current CH A (A) 2.00E-08 1.00E-08 0.00E+00 -1.00E-08 -2.00E-08 -3.00E-08 0 50 100 150 Total Dose (krad(Si)) Figure 5.5. Plot of input offset current, channel A @ +/-15V (A) versus total dose. The data show no significant degradation with total dose, however the degradation is not sufficient to cause the KTL statistics to go out of specification. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the unbiased sample. The black lines show the effects on the data after application of the biased KTL statistics (solid and dashed lines) while the gray lines show the effects on the data after application of the unbiased KTL statistics (solid and dashed lines). The red dashed lines are the minimum and maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2000 Certified Company 15 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 08-402 090317 R1.1 Table 5.5. Raw data of input offset current, channel A @ +/-15V (A) versus total dose, including the statistical analysis, the specification and the status of the testing (pass/fail). Total Dose (krad(Si)) Input Offset Current CH A (A) Device 1090 1092 1093 1094 1095 1096 1097 1098 1099 1100 1106 1113 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status 0 -2.09E-10 1.62E-10 -7.10E-11 -9.20E-11 1.75E-10 -6.00E-11 1.38E-10 1.27E-10 -3.06E-10 -1.18E-10 -1.34E-10 -7.70E-11 20 2.42E-10 2.23E-10 1.18E-10 -2.10E-11 2.61E-10 -1.18E-10 1.84E-10 2.90E-11 1.32E-10 -4.30E-11 9.30E-11 -9.20E-11 50 3.13E-10 -6.60E-11 -1.80E-11 4.77E-10 7.90E-11 2.77E-10 1.21E-10 1.93E-10 2.74E-10 1.35E-10 -2.13E-10 3.20E-11 100 5.77E-10 3.66E-10 5.73E-10 4.86E-10 4.19E-10 4.97E-10 5.06E-10 2.09E-10 4.34E-10 4.56E-10 -1.80E-10 -5.60E-11 200 1.33E-09 1.20E-09 2.13E-09 1.58E-09 1.41E-09 1.79E-09 1.03E-09 1.51E-09 1.66E-09 1.27E-09 -1.32E-10 -1.13E-10 -7.00E-12 1.69E-10 4.56E-10 -4.70E-10 1.65E-10 1.18E-10 4.87E-10 -1.58E-10 1.57E-10 2.31E-10 7.90E-10 -4.76E-10 4.84E-10 9.32E-11 7.40E-10 2.29E-10 1.53E-09 3.63E-10 2.52E-09 5.34E-10 -4.38E-11 1.85E-10 4.63E-10 -5.51E-10 -1.00E-08 PASS 1.00E-08 PASS 3.68E-11 1.24E-10 3.76E-10 -3.02E-10 -1.00E-08 PASS 1.00E-08 PASS 2.00E-10 7.40E-11 4.03E-10 -2.98E-12 -1.50E-08 PASS 1.50E-08 PASS 4.20E-10 1.22E-10 7.54E-10 8.64E-11 -2.00E-08 PASS 2.00E-08 PASS 1.45E-09 3.05E-10 2.29E-09 6.15E-10 -2.50E-08 PASS 2.50E-08 PASS An ISO 9001:2000 Certified Company 16 RLAT Report 08-402 090317 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 3.00E-08 Input Offset Current CH B (A) 2.00E-08 1.00E-08 0.00E+00 -1.00E-08 -2.00E-08 -3.00E-08 0 50 100 150 Total Dose (krad(Si)) Figure 5.6. Plot of input offset current, channel B @ +/-15V (A) versus total dose. The data show no significant degradation with total dose, however the degradation is not sufficient to cause the KTL statistics to go out of specification. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black lines show the effects on the data after application of the biased KTL statistics (solid and dashed lines) while the gray lines show the effects on the data after application of the unbiased KTL statistics (solid and dashed lines). The red dashed lines are the minimum and maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2000 Certified Company 17 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 08-402 090317 R1.1 Table 5.6. Raw data of input offset current, channel B @ +/-15V (A) versus total dose, including the statistical analysis, the specification and the status of the testing (pass/fail). Total Dose (krad(Si)) Input Offset Current CH B (A) Device 1090 1092 1093 1094 1095 1096 1097 1098 1099 1100 1106 1113 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status 0 -5.50E-11 1.29E-10 5.60E-11 1.34E-10 -3.40E-11 -2.56E-10 2.20E-11 -2.36E-10 -5.40E-11 2.22E-10 1.55E-10 -8.30E-11 20 6.70E-11 -1.80E-11 9.20E-11 2.46E-10 1.24E-10 1.95E-10 5.70E-11 -2.66E-10 1.22E-10 -1.90E-10 4.60E-11 -1.32E-10 50 -1.99E-10 -3.60E-11 5.25E-10 6.70E-11 -7.00E-11 2.34E-10 -7.60E-11 -2.10E-11 -2.40E-11 1.48E-10 6.80E-11 2.23E-10 100 5.56E-10 3.58E-10 8.73E-10 7.98E-10 3.83E-10 5.49E-10 4.15E-10 2.47E-10 3.79E-10 1.20E-11 8.50E-11 1.60E-10 200 8.85E-10 1.15E-09 2.30E-09 1.78E-09 1.26E-09 2.17E-09 1.09E-09 1.50E-09 1.67E-09 5.86E-10 -1.79E-10 9.50E-11 4.60E-11 8.85E-11 2.89E-10 -1.97E-10 1.02E-10 9.61E-11 3.66E-10 -1.61E-10 5.74E-11 2.78E-10 8.20E-10 -7.05E-10 5.94E-10 2.35E-10 1.24E-09 -5.11E-11 1.48E-09 5.64E-10 3.02E-09 -7.12E-11 -6.04E-11 1.97E-10 4.81E-10 -6.01E-10 -1.00E-08 PASS 1.00E-08 PASS -1.64E-11 2.01E-10 5.35E-10 -5.68E-10 -1.00E-08 PASS 1.00E-08 PASS 5.22E-11 1.32E-10 4.14E-10 -3.10E-10 -1.50E-08 PASS 1.50E-08 PASS 3.20E-10 2.03E-10 8.78E-10 -2.37E-10 -2.00E-08 PASS 2.00E-08 PASS 1.40E-09 5.98E-10 3.04E-09 -2.40E-10 -2.50E-08 PASS 2.50E-08 PASS An ISO 9001:2000 Certified Company 18 RLAT Report 08-402 090317 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 3.00E-07 + Input Bias Current CH A (A) 2.00E-07 1.00E-07 0.00E+00 -1.00E-07 -2.00E-07 -3.00E-07 0 50 100 150 Total Dose (krad(Si)) Figure 5.7. Plot of input bias current, non-inverting input @ +/-15V (A) for channel A versus total dose. The data show only a slight increase with total dose. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black lines show the effects on the data after application of the biased KTL statistics (solid and dashed lines) while the gray lines show the effects on the data after application of the unbiased KTL statistics (solid and dashed lines). The red dashed lines are the minimum and maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2000 Certified Company 19 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 08-402 090317 R1.1 Table 5.7. Raw data of the input bias current, non-inverting input @ +/-15V (A) for channel A versus total dose, including the statistical analysis, the specification and the status of the testing (pass/fail). Total Dose (krad(Si)) + Input Bias Current CH A (A) Device 1090 1092 1093 1094 1095 1096 1097 1098 1099 1100 1106 1113 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status 0 1.04E-08 1.04E-08 9.95E-09 1.13E-08 1.09E-08 1.06E-08 1.12E-08 1.09E-08 1.11E-08 1.03E-08 1.06E-08 1.09E-08 20 1.40E-08 1.40E-08 1.34E-08 1.50E-08 1.46E-08 1.39E-08 1.47E-08 1.46E-08 1.45E-08 1.37E-08 1.06E-08 1.09E-08 50 2.15E-08 2.14E-08 2.02E-08 2.26E-08 2.20E-08 2.02E-08 2.14E-08 2.13E-08 2.14E-08 2.04E-08 1.07E-08 1.09E-08 100 3.33E-08 3.32E-08 3.11E-08 3.49E-08 3.39E-08 3.07E-08 3.23E-08 3.26E-08 3.26E-08 3.15E-08 1.06E-08 1.09E-08 200 5.53E-08 5.57E-08 5.09E-08 5.75E-08 5.62E-08 4.99E-08 5.25E-08 5.18E-08 5.22E-08 5.13E-08 1.07E-08 1.09E-08 1.06E-08 5.13E-10 1.20E-08 9.19E-09 1.42E-08 6.29E-10 1.59E-08 1.25E-08 2.15E-08 9.07E-10 2.40E-08 1.90E-08 3.33E-08 1.43E-09 3.72E-08 2.94E-08 5.51E-08 2.51E-09 6.20E-08 4.82E-08 1.08E-08 3.71E-10 1.18E-08 9.80E-09 -3.00E-08 PASS 3.00E-08 PASS 1.43E-08 4.34E-10 1.55E-08 1.31E-08 -7.50E-08 PASS 7.50E-08 PASS 2.09E-08 5.81E-10 2.25E-08 1.93E-08 -1.00E-07 PASS 1.00E-07 PASS 3.19E-08 8.40E-10 3.42E-08 2.96E-08 -1.75E-07 PASS 1.75E-07 PASS 5.15E-08 1.03E-09 5.43E-08 4.87E-08 -2.50E-07 PASS 2.50E-07 PASS An ISO 9001:2000 Certified Company 20 RLAT Report 08-402 090317 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 3.00E-07 + Input Bias Current CH B (A) 2.00E-07 1.00E-07 0.00E+00 -1.00E-07 -2.00E-07 -3.00E-07 0 50 100 150 Total Dose (krad(Si)) Figure 5.8. Plot of input bias current, non-inverting input @ +/-15V (A) for channel B versus total dose. The data show only a slight increase with total dose. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black lines show the effects on the data after application of the biased KTL statistics (solid and dashed lines) while the gray lines show the effects on the data after application of the unbiased KTL statistics (solid and dashed lines). The red dashed lines are the minimum and maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2000 Certified Company 21 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 08-402 090317 R1.1 Table 5.8. Raw data of the input bias current, non-inverting input @ +/-15V (A) for channel B versus total dose, including the statistical analysis, the specification and the status of the testing (pass/fail). Total Dose (krad(Si)) + Input Bias Current CH B (A) Device 1090 1092 1093 1094 1095 1096 1097 1098 1099 1100 1106 1113 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status 0 1.08E-08 1.08E-08 1.08E-08 1.18E-08 1.14E-08 1.15E-08 1.17E-08 1.12E-08 1.15E-08 1.13E-08 1.11E-08 1.07E-08 20 1.45E-08 1.45E-08 1.44E-08 1.56E-08 1.52E-08 1.51E-08 1.54E-08 1.50E-08 1.51E-08 1.49E-08 1.10E-08 1.07E-08 50 2.21E-08 2.21E-08 2.17E-08 2.35E-08 2.29E-08 2.20E-08 2.21E-08 2.20E-08 2.21E-08 2.22E-08 1.10E-08 1.08E-08 100 3.41E-08 3.45E-08 3.33E-08 3.61E-08 3.54E-08 3.32E-08 3.34E-08 3.36E-08 3.39E-08 3.39E-08 1.10E-08 1.07E-08 200 5.65E-08 5.77E-08 5.46E-08 5.94E-08 5.83E-08 5.36E-08 5.42E-08 5.33E-08 5.41E-08 5.52E-08 1.10E-08 1.07E-08 1.11E-08 4.56E-10 1.24E-08 9.85E-09 1.48E-08 5.44E-10 1.63E-08 1.34E-08 2.25E-08 7.11E-10 2.44E-08 2.05E-08 3.47E-08 1.08E-09 3.76E-08 3.17E-08 5.73E-08 1.84E-09 6.23E-08 5.23E-08 1.14E-08 2.22E-10 1.20E-08 1.08E-08 -3.00E-08 PASS 3.00E-08 PASS 1.51E-08 1.84E-10 1.56E-08 1.46E-08 -7.50E-08 PASS 7.50E-08 PASS 2.21E-08 9.69E-11 2.23E-08 2.18E-08 -1.00E-07 PASS 1.00E-07 PASS 3.36E-08 2.93E-10 3.44E-08 3.28E-08 -1.75E-07 PASS 1.75E-07 PASS 5.41E-08 7.25E-10 5.61E-08 5.21E-08 -2.50E-07 PASS 2.50E-07 PASS An ISO 9001:2000 Certified Company 22 RLAT Report 08-402 090317 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 3.00E-07 - Input Bias Current CH A (A) 2.00E-07 1.00E-07 0.00E+00 -1.00E-07 -2.00E-07 -3.00E-07 0 50 100 150 200 Total Dose (krad(Si)) Figure 5.9. Plot of input bias current, inverting input @ +/-15V for channel A versus total dose. The data show only a slight increase with total dose. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black lines show the effects on the data after application of the biased KTL statistics (solid and dashed lines) while the gray lines show the effects on the data after application of the unbiased KTL statistics (solid and dashed lines). The red dashed lines are the minimum and maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2000 Certified Company 23 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 08-402 090317 R1.1 Table 5.9. Raw data for the input bias current, inverting input @ +/-15V for channel A versus total dose, including the statistical analysis, the specification and the status of the testing (pass/fail). Total Dose (krad(Si)) - Input Bias Current CH A (A) Device 1090 1092 1093 1094 1095 1096 1097 1098 1099 1100 1106 1113 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status 0 1.04E-08 1.05E-08 1.01E-08 1.13E-08 1.11E-08 1.08E-08 1.13E-08 1.11E-08 1.10E-08 1.04E-08 1.05E-08 1.10E-08 20 1.41E-08 1.41E-08 1.36E-08 1.50E-08 1.46E-08 1.39E-08 1.48E-08 1.47E-08 1.45E-08 1.40E-08 1.05E-08 1.11E-08 50 2.19E-08 2.15E-08 2.04E-08 2.31E-08 2.23E-08 2.05E-08 2.17E-08 2.15E-08 2.16E-08 2.05E-08 1.05E-08 1.09E-08 100 3.39E-08 3.38E-08 3.19E-08 3.57E-08 3.48E-08 3.14E-08 3.27E-08 3.32E-08 3.34E-08 3.22E-08 1.04E-08 1.08E-08 200 5.67E-08 5.71E-08 5.31E-08 5.97E-08 5.77E-08 5.18E-08 5.38E-08 5.37E-08 5.43E-08 5.27E-08 1.06E-08 1.09E-08 1.07E-08 4.99E-10 1.21E-08 9.32E-09 1.43E-08 5.29E-10 1.57E-08 1.28E-08 2.18E-08 1.01E-09 2.46E-08 1.91E-08 3.40E-08 1.43E-09 3.79E-08 3.01E-08 5.69E-08 2.41E-09 6.35E-08 5.03E-08 1.09E-08 3.62E-10 1.19E-08 9.91E-09 -3.00E-08 PASS 3.00E-08 PASS 1.44E-08 3.86E-10 1.54E-08 1.33E-08 -7.50E-08 PASS 7.50E-08 PASS 2.12E-08 6.00E-10 2.28E-08 1.95E-08 -1.00E-07 PASS 1.00E-07 PASS 3.26E-08 8.05E-10 3.48E-08 3.04E-08 -1.75E-07 PASS 1.75E-07 PASS 5.33E-08 1.01E-09 5.60E-08 5.05E-08 -2.50E-07 PASS 2.50E-07 PASS An ISO 9001:2000 Certified Company 24 RLAT Report 08-402 090317 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 3.00E-07 - Input Bias Current CH B (A) 2.00E-07 1.00E-07 0.00E+00 -1.00E-07 -2.00E-07 -3.00E-07 0 50 100 150 Total Dose (krad(Si)) Figure 5.10. Plot of input bias current, inverting input @ +/-15V for channel B versus total dose. The data show only a slight increase with total dose. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black lines show the effects on the data after application of the biased KTL statistics (solid and dashed lines) while the gray lines show the effects on the data after application of the unbiased KTL statistics (solid and dashed lines). The red dashed lines are the minimum and maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2000 Certified Company 25 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 08-402 090317 R1.1 Table 5.10. Raw data for the input bias current, inverting input @ +/-15V for channel B versus total dose, including the statistical analysis, the specification and the status of the testing (pass/fail). Total Dose (krad(Si)) - Input Bias Current CH B (A) Device 1090 1092 1093 1094 1095 1096 1097 1098 1099 1100 1106 1113 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status 0 1.07E-08 1.10E-08 1.08E-08 1.20E-08 1.14E-08 1.14E-08 1.17E-08 1.11E-08 1.13E-08 1.15E-08 1.12E-08 1.06E-08 20 1.46E-08 1.47E-08 1.47E-08 1.59E-08 1.55E-08 1.50E-08 1.53E-08 1.51E-08 1.52E-08 1.49E-08 1.12E-08 1.06E-08 50 2.21E-08 2.20E-08 2.22E-08 2.39E-08 2.30E-08 2.24E-08 2.21E-08 2.21E-08 2.24E-08 2.22E-08 1.09E-08 1.07E-08 100 3.45E-08 3.47E-08 3.46E-08 3.69E-08 3.61E-08 3.36E-08 3.40E-08 3.38E-08 3.42E-08 3.41E-08 1.10E-08 1.07E-08 200 5.79E-08 5.90E-08 5.73E-08 6.14E-08 6.00E-08 5.58E-08 5.56E-08 5.50E-08 5.58E-08 5.59E-08 1.09E-08 1.06E-08 1.12E-08 5.46E-10 1.27E-08 9.69E-09 1.51E-08 5.81E-10 1.67E-08 1.35E-08 2.27E-08 7.90E-10 2.48E-08 2.05E-08 3.54E-08 1.07E-09 3.83E-08 3.24E-08 5.91E-08 1.64E-09 6.36E-08 5.46E-08 1.14E-08 2.42E-10 1.21E-08 1.08E-08 -3.00E-08 PASS 3.00E-08 PASS 1.51E-08 1.74E-10 1.56E-08 1.46E-08 -7.50E-08 PASS 7.50E-08 PASS 2.23E-08 1.50E-10 2.27E-08 2.18E-08 -1.00E-07 PASS 1.00E-07 PASS 3.40E-08 2.50E-10 3.46E-08 3.33E-08 -1.75E-07 PASS 1.75E-07 PASS 5.56E-08 3.79E-10 5.67E-08 5.46E-08 -2.50E-07 PASS 2.50E-07 PASS An ISO 9001:2000 Certified Company 26 RLAT Report 08-402 090317 R1.1 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (-KTL) Biased Common Mode Rejection Ratio CH A (dB) 1.30E+02 1.20E+02 1.10E+02 1.00E+02 9.00E+01 8.00E+01 7.00E+01 6.00E+01 5.00E+01 0 50 100 150 Total Dose (krad(Si)) Figure 5.11. Plot of common mode rejection ratio for channel A versus total dose. Although the data show a decrease with total dose, it is not sufficient to fall below the specification value. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black lines show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray lines show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed lines are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2000 Certified Company 27 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 08-402 090317 R1.1 Table 5.11. Raw data of the common mode rejection ratio for channel A versus total dose, including the statistical analysis, the specification and the status of the testing (pass/fail). Total Dose (krad(Si)) Common Mode Rejection Ratio CH A (dB) Device 1090 1092 1093 1094 1095 1096 1097 1098 1099 1100 1106 1113 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status 0 1.26E+02 1.20E+02 1.18E+02 1.14E+02 1.22E+02 1.24E+02 1.22E+02 1.29E+02 1.23E+02 1.13E+02 1.23E+02 1.16E+02 20 1.23E+02 1.17E+02 1.15E+02 1.12E+02 1.16E+02 1.19E+02 1.18E+02 1.20E+02 1.17E+02 1.11E+02 1.23E+02 1.16E+02 50 1.28E+02 1.16E+02 1.14E+02 1.10E+02 1.16E+02 1.15E+02 1.16E+02 1.18E+02 1.14E+02 1.09E+02 1.28E+02 1.17E+02 100 1.22E+02 1.14E+02 1.12E+02 1.09E+02 1.14E+02 1.14E+02 1.13E+02 1.16E+02 1.12E+02 1.08E+02 1.23E+02 1.16E+02 200 1.18E+02 1.13E+02 1.11E+02 1.08E+02 1.13E+02 1.11E+02 1.12E+02 1.15E+02 1.11E+02 1.07E+02 1.23E+02 1.18E+02 1.20E+02 4.48E+00 1.32E+02 1.08E+02 1.16E+02 4.16E+00 1.28E+02 1.05E+02 1.17E+02 6.52E+00 1.35E+02 9.89E+01 1.14E+02 4.66E+00 1.27E+02 1.02E+02 1.13E+02 3.37E+00 1.22E+02 1.04E+02 1.22E+02 5.83E+00 1.38E+02 1.06E+02 9.70E+01 PASS 1.17E+02 3.63E+00 1.27E+02 1.07E+02 9.70E+01 PASS 1.14E+02 3.38E+00 1.24E+02 1.05E+02 9.40E+01 PASS 1.13E+02 2.81E+00 1.20E+02 1.05E+02 9.00E+01 PASS 1.11E+02 2.84E+00 1.19E+02 1.03E+02 8.60E+01 PASS An ISO 9001:2000 Certified Company 28 RLAT Report 08-402 090317 R1.1 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (-KTL) Biased Common Mode Rejection Ratio CH B (dB) 1.30E+02 1.20E+02 1.10E+02 1.00E+02 9.00E+01 8.00E+01 7.00E+01 6.00E+01 5.00E+01 0 50 100 150 Total Dose (krad(Si)) Figure 5.12. Plot of common mode rejection ratio for channel B versus total dose. Although the data show a decrease with total dose, it is not sufficient to fall below the specification value. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black lines show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray lines show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed lines are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2000 Certified Company 29 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 08-402 090317 R1.1 Table 5.12. Raw data of the common mode rejection ratio for channel B versus total dose, including the statistical analysis, the specification and the status of the testing (pass/fail). Total Dose (krad(Si)) Common Mode Rejection Ratio CH B (dB) Device 1090 1092 1093 1094 1095 1096 1097 1098 1099 1100 1106 1113 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status 0 1.18E+02 1.12E+02 1.17E+02 1.13E+02 1.17E+02 1.17E+02 1.15E+02 1.30E+02 1.15E+02 1.14E+02 1.11E+02 1.15E+02 20 1.15E+02 1.11E+02 1.14E+02 1.11E+02 1.15E+02 1.14E+02 1.13E+02 1.27E+02 1.13E+02 1.12E+02 1.12E+02 1.15E+02 50 1.13E+02 1.10E+02 1.13E+02 1.10E+02 1.13E+02 1.12E+02 1.11E+02 1.26E+02 1.11E+02 1.10E+02 1.12E+02 1.15E+02 100 1.12E+02 1.09E+02 1.12E+02 1.09E+02 1.12E+02 1.11E+02 1.10E+02 1.20E+02 1.10E+02 1.09E+02 1.12E+02 1.15E+02 200 1.11E+02 1.08E+02 1.11E+02 1.08E+02 1.11E+02 1.09E+02 1.09E+02 1.18E+02 1.08E+02 1.08E+02 1.11E+02 1.15E+02 1.15E+02 2.56E+00 1.22E+02 1.08E+02 1.13E+02 2.02E+00 1.19E+02 1.08E+02 1.12E+02 1.75E+00 1.17E+02 1.07E+02 1.11E+02 1.70E+00 1.15E+02 1.06E+02 1.10E+02 1.49E+00 1.14E+02 1.06E+02 1.18E+02 6.37E+00 1.36E+02 1.01E+02 9.70E+01 PASS 1.16E+02 6.31E+00 1.33E+02 9.86E+01 9.70E+01 PASS 1.14E+02 6.77E+00 1.33E+02 9.57E+01 9.40E+01 PASS 1.12E+02 4.69E+00 1.25E+02 9.89E+01 9.00E+01 PASS 1.10E+02 4.04E+00 1.21E+02 9.93E+01 8.60E+01 PASS An ISO 9001:2000 Certified Company 30 RLAT Report 08-402 090317 R1.1 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (-KTL) Biased Power Supply Rejection Ratio CH A (dB) 1.40E+02 1.30E+02 1.20E+02 1.10E+02 1.00E+02 9.00E+01 8.00E+01 7.00E+01 6.00E+01 5.00E+01 0 50 100 150 Total Dose (krad(Si)) Figure 5.13. Plot of power supply rejection ratio for channel A versus total dose. Although the data show a decrease with total dose, it is not sufficient to fall below the specification value. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black lines show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray lines show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed lines are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2000 Certified Company 31 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 08-402 090317 R1.1 Table 5.13. Raw data of the power supply rejection ratio for channel A versus total dose, including the statistical analysis, the specification and the status of the testing (pass/fail). Total Dose (krad(Si)) Power Supply Rejection Ratio CH A (dB) Device 1090 1092 1093 1094 1095 1096 1097 1098 1099 1100 1106 1113 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status 0 1.35E+02 1.31E+02 1.33E+02 1.20E+02 1.49E+02 1.36E+02 1.31E+02 1.31E+02 1.28E+02 1.31E+02 1.25E+02 1.32E+02 20 1.34E+02 1.35E+02 1.29E+02 1.17E+02 1.32E+02 1.45E+02 1.44E+02 1.25E+02 1.29E+02 1.23E+02 1.27E+02 1.58E+02 50 1.26E+02 1.49E+02 1.49E+02 1.16E+02 1.38E+02 1.32E+02 1.42E+02 1.35E+02 1.24E+02 1.20E+02 1.30E+02 1.37E+02 100 1.38E+02 1.25E+02 1.41E+02 1.16E+02 1.29E+02 1.32E+02 1.33E+02 1.30E+02 1.19E+02 1.20E+02 1.26E+02 1.36E+02 200 1.26E+02 1.26E+02 1.31E+02 1.14E+02 1.23E+02 1.25E+02 1.22E+02 1.29E+02 1.16E+02 1.14E+02 1.30E+02 1.37E+02 1.34E+02 1.04E+01 1.62E+02 1.05E+02 1.29E+02 7.40E+00 1.49E+02 1.09E+02 1.36E+02 1.45E+01 1.75E+02 9.57E+01 1.30E+02 9.90E+00 1.57E+02 1.03E+02 1.24E+02 6.34E+00 1.41E+02 1.07E+02 1.32E+02 2.83E+00 1.39E+02 1.24E+02 1.00E+02 PASS 1.33E+02 1.05E+01 1.62E+02 1.04E+02 9.80E+01 PASS 1.31E+02 8.79E+00 1.55E+02 1.06E+02 9.40E+01 PASS 1.27E+02 6.65E+00 1.45E+02 1.09E+02 8.60E+01 PASS 1.21E+02 6.08E+00 1.38E+02 1.05E+02 8.00E+01 PASS An ISO 9001:2000 Certified Company 32 RLAT Report 08-402 090317 R1.1 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (-KTL) Biased Power Supply Rejection Ratio CH B (dB) 1.50E+02 1.40E+02 1.30E+02 1.20E+02 1.10E+02 1.00E+02 9.00E+01 8.00E+01 7.00E+01 6.00E+01 5.00E+01 0 50 100 150 Total Dose (krad(Si)) Figure 5.14. Plot of power supply rejection ratio for channel B versus total dose. Although the data show a decrease with total dose, it is not sufficient to fall below the specification value. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black lines show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray lines show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed lines are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2000 Certified Company 33 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 08-402 090317 R1.1 Table 5.14. Raw data of the power supply rejection ratio for channel B versus total dose, including the statistical analysis, the specification and the status of the testing (pass/fail). Total Dose (krad(Si)) Power Supply Rejection Ratio CH B (dB) Device 1090 1092 1093 1094 1095 1096 1097 1098 1099 1100 1106 1113 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status 0 1.40E+02 1.31E+02 1.22E+02 1.32E+02 1.32E+02 1.36E+02 1.32E+02 1.29E+02 1.23E+02 1.29E+02 1.30E+02 1.28E+02 20 1.47E+02 1.41E+02 1.21E+02 1.27E+02 1.48E+02 1.36E+02 1.27E+02 1.25E+02 1.22E+02 1.42E+02 1.29E+02 1.25E+02 50 1.45E+02 1.39E+02 1.24E+02 1.23E+02 1.47E+02 1.30E+02 1.23E+02 1.33E+02 1.20E+02 1.37E+02 1.27E+02 1.29E+02 100 1.32E+02 1.34E+02 1.23E+02 1.22E+02 1.43E+02 1.22E+02 1.21E+02 1.30E+02 1.17E+02 1.31E+02 1.31E+02 1.28E+02 200 1.22E+02 1.30E+02 1.28E+02 1.18E+02 1.25E+02 1.18E+02 1.17E+02 1.24E+02 1.13E+02 1.18E+02 1.28E+02 1.30E+02 1.31E+02 6.59E+00 1.50E+02 1.13E+02 1.37E+02 1.21E+01 1.70E+02 1.04E+02 1.36E+02 1.13E+01 1.67E+02 1.05E+02 1.31E+02 8.56E+00 1.54E+02 1.07E+02 1.25E+02 4.78E+00 1.38E+02 1.12E+02 1.30E+02 4.95E+00 1.43E+02 1.16E+02 1.00E+02 PASS 1.31E+02 8.00E+00 1.52E+02 1.09E+02 9.80E+01 PASS 1.29E+02 7.01E+00 1.48E+02 1.10E+02 9.40E+01 PASS 1.24E+02 6.04E+00 1.41E+02 1.08E+02 8.60E+01 PASS 1.18E+02 3.96E+00 1.29E+02 1.07E+02 8.00E+01 PASS An ISO 9001:2000 Certified Company 34 RLAT Report 08-402 090317 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN 2.00E+04 Large Signal Voltage Gain CH A (V/mV) 1.80E+04 1.60E+04 1.40E+04 1.20E+04 1.00E+04 8.00E+03 6.00E+03 4.00E+03 2.00E+03 0.00E+00 0 50 100 150 Total Dose (krad(Si)) Figure 5.15. Plot of open loop gain for channel A versus total dose. Although the data show a substantial decrease AVOL with total dose, it is not sufficient to fall below the specification value, including after application of the KTL statistics. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black lines show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray lines show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed lines are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. See Appendix D, Figure D.1 for the data in dB. An ISO 9001:2000 Certified Company 35 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 08-402 090317 R1.1 Table 5.15. Raw data of the open loop gain for channel A versus total dose, including the statistical analysis, the specification and the status of the testing (pass/fail). See Appendix D, Table D.1 for the data in dB. Total Dose (krad(Si)) Large Signal Voltage Gain CH A (V/mV) Device 1090 1092 1093 1094 1095 1096 1097 1098 1099 1100 1106 1113 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status 0 1.78E+04 1.95E+04 1.65E+04 1.51E+04 1.41E+04 1.58E+04 1.61E+04 1.83E+04 1.51E+04 1.90E+04 2.17E+04 1.50E+04 20 1.62E+04 1.66E+04 2.10E+04 1.11E+04 1.91E+04 1.45E+04 1.40E+04 1.40E+04 2.03E+04 1.92E+04 1.51E+04 2.01E+04 50 2.06E+04 1.94E+04 1.42E+04 1.81E+04 1.57E+04 1.77E+04 1.67E+04 1.91E+04 2.21E+04 1.26E+04 1.83E+04 1.88E+04 100 1.30E+04 1.46E+04 1.79E+04 1.44E+04 1.30E+04 2.18E+04 2.04E+04 1.33E+04 1.64E+04 1.64E+04 1.65E+04 1.56E+04 200 1.75E+04 1.42E+04 1.76E+04 2.57E+04 1.88E+04 2.24E+04 1.56E+04 1.50E+04 1.87E+04 1.71E+04 1.63E+04 1.21E+04 1.66E+04 2.15E+03 2.25E+04 1.07E+04 1.68E+04 3.76E+03 2.71E+04 6.48E+03 1.76E+04 2.64E+03 2.48E+04 1.04E+04 1.46E+04 2.02E+03 2.01E+04 9.06E+03 1.87E+04 4.25E+03 3.04E+04 7.11E+03 1.69E+04 1.66E+03 2.14E+04 1.23E+04 1.20E+03 PASS 1.64E+04 3.08E+03 2.48E+04 7.98E+03 2.00E+02 PASS 1.76E+04 3.49E+03 2.72E+04 8.06E+03 1.00E+02 PASS An ISO 9001:2000 Certified Company 36 1.77E+04 1.78E+04 3.40E+03 2.95E+03 2.70E+04 2.59E+04 8.34E+03 9.68E+03 5.00E+01 2.50E+01 PASS PASS RLAT Report 08-402 090317 R1.1 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (-KTL) Biased Large Signal Voltage Gain CH B (V/mV) 3.50E+04 3.00E+04 2.50E+04 2.00E+04 1.50E+04 1.00E+04 5.00E+03 0.00E+00 0 50 100 150 Total Dose (krad(Si)) Figure 5.16. Plot of open loop gain for channel B versus total dose. Although the data show a substantial decrease AVOL with total dose, it is not sufficient to fall below the specification value, including after application of the KTL statistics. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black lines show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray lines show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed lines are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. See Appendix D, Figure D.2 for the data in dB. An ISO 9001:2000 Certified Company 37 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 08-402 090317 R1.1 Table 5.16. Raw data of the open loop gain for channel B versus total dose, including the statistical analysis, the specification and the status of the testing (pass/fail). . See Appendix D, Table D.2 for the data in dB. Total Dose (krad(Si)) Large Signal Voltage Gain CH B (V/mV) Device 1090 1092 1093 1094 1095 1096 1097 1098 1099 1100 1106 1113 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status 0 2.39E+04 2.63E+04 2.39E+04 2.29E+04 2.24E+04 2.50E+04 3.17E+04 2.77E+04 2.24E+04 2.50E+04 2.55E+04 1.92E+04 20 2.54E+04 3.36E+04 2.60E+04 3.17E+04 3.21E+04 2.78E+04 2.41E+04 2.47E+04 3.24E+04 2.64E+04 2.94E+04 2.30E+04 50 2.81E+04 2.17E+04 3.66E+04 2.65E+04 2.75E+04 2.41E+04 2.74E+04 3.23E+04 2.58E+04 3.05E+04 3.13E+04 2.44E+04 100 2.77E+04 2.97E+04 3.15E+04 3.82E+04 2.91E+04 2.58E+04 2.70E+04 2.81E+04 2.87E+04 2.76E+04 2.40E+04 2.64E+04 200 2.70E+04 3.15E+04 3.01E+04 3.19E+04 2.32E+04 2.71E+04 2.77E+04 1.89E+04 2.31E+04 1.98E+04 3.24E+04 3.21E+04 2.39E+04 1.53E+03 2.81E+04 1.97E+04 2.97E+04 3.78E+03 4.01E+04 1.94E+04 2.81E+04 5.37E+03 4.28E+04 1.33E+04 3.12E+04 4.12E+03 4.25E+04 1.99E+04 2.87E+04 3.66E+03 3.88E+04 1.87E+04 2.64E+04 3.52E+03 3.60E+04 1.67E+04 1.20E+03 PASS 2.71E+04 3.33E+03 3.62E+04 1.80E+04 2.00E+02 PASS 2.80E+04 3.36E+03 3.72E+04 1.88E+04 1.00E+02 PASS 2.74E+04 1.12E+03 3.05E+04 2.44E+04 5.00E+01 PASS 2.33E+04 4.04E+03 3.44E+04 1.22E+04 2.50E+01 PASS An ISO 9001:2000 Certified Company 38 RLAT Report 08-402 090317 R1.1 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (-KTL) Biased 1.42E+01 Positive Output Voltage Swing CH A (V) 1.40E+01 1.38E+01 1.36E+01 1.34E+01 1.32E+01 1.30E+01 1.28E+01 1.26E+01 1.24E+01 0 50 100 150 Total Dose (krad(Si)) Figure 5.17. Plot of positive output voltage swing for channel A versus total dose. The data show no significant decrease with total dose. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black lines show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray lines show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed lines are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2000 Certified Company 39 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 08-402 090317 R1.1 Table 5.17. Raw data of the positive output voltage swing for channel A versus total dose, including the statistical analysis, the specification and the status of the testing (pass/fail). Total Dose (krad(Si)) Positive Output Voltage Swing CH A (V) Device 1090 1092 1093 1094 1095 1096 1097 1098 1099 1100 1106 1113 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status 0 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 20 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 50 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 100 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 200 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 6.80E-03 1.41E+01 1.41E+01 1.41E+01 6.27E-03 1.41E+01 1.41E+01 1.41E+01 6.58E-03 1.41E+01 1.41E+01 1.41E+01 7.13E-03 1.41E+01 1.41E+01 1.41E+01 7.02E-03 1.41E+01 1.41E+01 1.41E+01 6.52E-03 1.41E+01 1.41E+01 1.25E+01 PASS 1.41E+01 6.72E-03 1.41E+01 1.41E+01 1.25E+01 PASS 1.41E+01 6.07E-03 1.41E+01 1.41E+01 1.25E+01 PASS 1.41E+01 7.80E-03 1.41E+01 1.41E+01 1.25E+01 PASS 1.41E+01 7.40E-03 1.41E+01 1.41E+01 1.25E+01 PASS An ISO 9001:2000 Certified Company 40 RLAT Report 08-402 090317 R1.1 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (-KTL) Biased Positive Output Voltage Swing CH B (V) 1.42E+01 1.40E+01 1.38E+01 1.36E+01 1.34E+01 1.32E+01 1.30E+01 1.28E+01 1.26E+01 1.24E+01 0 50 100 150 200 Total Dose (krad(Si)) Figure 5.18. Plot of positive output voltage swing for channel B versus total dose. The data show no significant decrease with total dose. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black lines show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray lines show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed lines are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2000 Certified Company 41 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 08-402 090317 R1.1 Table 5.18. Raw data of the positive output voltage swing for channel B versus total dose, including the statistical analysis, the specification and the status of the testing (pass/fail). Total Dose (krad(Si)) Positive Output Voltage Swing CH B (V) Device 1090 1092 1093 1094 1095 1096 1097 1098 1099 1100 1106 1113 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status 0 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 20 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 50 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 100 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 200 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 6.82E-03 1.41E+01 1.41E+01 1.41E+01 5.55E-03 1.41E+01 1.41E+01 1.41E+01 6.47E-03 1.41E+01 1.41E+01 1.41E+01 6.93E-03 1.41E+01 1.41E+01 1.41E+01 7.28E-03 1.41E+01 1.41E+01 1.41E+01 6.02E-03 1.41E+01 1.41E+01 1.25E+01 PASS 1.41E+01 6.39E-03 1.41E+01 1.41E+01 1.25E+01 PASS 1.41E+01 5.93E-03 1.41E+01 1.41E+01 1.25E+01 PASS 1.41E+01 7.14E-03 1.41E+01 1.41E+01 1.25E+01 PASS 1.41E+01 7.43E-03 1.41E+01 1.41E+01 1.25E+01 PASS An ISO 9001:2000 Certified Company 42 RLAT Report 08-402 090317 R1.1 Average Biased Average Un-Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (+KTL) Biased Negative Output Voltage Swing CH A (V) -1.20E+01 -1.25E+01 -1.30E+01 -1.35E+01 -1.40E+01 -1.45E+01 -1.50E+01 0 50 100 150 200 Total Dose (krad(Si)) Figure 5.19. Plot of negative output voltage swing for channel A versus total dose. The data show no significant decrease with total dose. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black lines show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray lines show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed lines are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2000 Certified Company 43 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 08-402 090317 R1.1 Table 5.19. Raw data of the negative output voltage swing for channel A versus total dose, including the statistical analysis, the specification and the status of the testing (pass/fail). Total Dose (krad(Si)) Negative Output Voltage Swing CH A (V) Device 1090 1092 1093 1094 1095 1096 1097 1098 1099 1100 1106 1113 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MAX Status 0 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 20 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 50 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 100 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 200 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 3.03E-03 3.63E-03 2.88E-03 3.03E-03 4.88E-03 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 2.83E-03 -1.44E+01 -1.44E+01 -1.25E+01 PASS -1.44E+01 2.55E-03 -1.44E+01 -1.44E+01 -1.25E+01 PASS -1.44E+01 2.41E-03 -1.44E+01 -1.44E+01 -1.25E+01 PASS An ISO 9001:2000 Certified Company 44 -1.44E+01 2.92E-03 -1.44E+01 -1.44E+01 -1.25E+01 PASS -1.44E+01 1.95E-03 -1.44E+01 -1.44E+01 -1.25E+01 PASS RLAT Report 08-402 090317 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Negative Output Voltage Swing CH B (V) -1.20E+01 -1.25E+01 -1.30E+01 -1.35E+01 -1.40E+01 -1.45E+01 -1.50E+01 0 50 100 150 Total Dose (krad(Si)) Figure 5.20. Plot of negative output voltage swing for channel B versus total dose. The data show no significant decrease with total dose. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black lines show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray lines show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed lines are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2000 Certified Company 45 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 08-402 090317 R1.1 Table 5.20. Raw data of the negative output voltage swing for channel B versus total dose, including the statistical analysis, the specification and the status of the testing (pass/fail). Total Dose (krad(Si)) Negative Output Voltage Swing CH B (V) Device 1090 1092 1093 1094 1095 1096 1097 1098 1099 1100 1106 1113 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MAX Status 0 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 20 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 50 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 100 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 200 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 3.03E-03 3.63E-03 3.13E-03 3.44E-03 4.47E-03 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 3.44E-03 -1.44E+01 -1.44E+01 -1.25E+01 PASS -1.44E+01 2.68E-03 -1.44E+01 -1.44E+01 -1.25E+01 PASS -1.44E+01 2.77E-03 -1.44E+01 -1.44E+01 -1.25E+01 PASS An ISO 9001:2000 Certified Company 46 -1.44E+01 2.68E-03 -1.44E+01 -1.44E+01 -1.25E+01 PASS -1.44E+01 2.00E-03 -1.44E+01 -1.44E+01 -1.25E+01 PASS RLAT Report 08-402 090317 R1.1 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (-KTL) Biased 6.00E-01 Positive Slew Rate CH A (V/µs) 5.00E-01 4.00E-01 3.00E-01 2.00E-01 1.00E-01 0.00E+00 0 50 100 150 Total Dose (krad(Si)) Figure 5.21. Plot of positive slew rate for channel A versus total dose. The data show a moderate decrease with total dose, however not sufficient to fall below the specification, even after application of the KTL statistics. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black lines show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray lines show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed lines are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2000 Certified Company 47 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 08-402 090317 R1.1 Table 5.21. Raw data of the positive slew rate for channel A versus total dose, including the statistical analysis, the specification and the status of the testing (pass/fail). Total Dose (krad(Si)) Positive Slew Rate CH A (V/µs) Device 1090 1092 1093 1094 1095 1096 1097 1098 1099 1100 1106 1113 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status 0 4.82E-01 4.97E-01 5.01E-01 4.56E-01 5.01E-01 4.90E-01 4.68E-01 4.76E-01 4.79E-01 4.73E-01 4.75E-01 4.77E-01 20 4.74E-01 4.94E-01 4.87E-01 4.56E-01 4.85E-01 4.84E-01 4.60E-01 4.76E-01 4.70E-01 4.64E-01 4.88E-01 4.71E-01 50 4.60E-01 4.87E-01 4.84E-01 4.31E-01 4.85E-01 4.60E-01 4.35E-01 4.58E-01 4.54E-01 4.50E-01 4.87E-01 4.69E-01 100 4.31E-01 4.49E-01 4.42E-01 4.07E-01 4.51E-01 4.24E-01 4.09E-01 4.32E-01 4.24E-01 4.12E-01 4.82E-01 4.72E-01 200 3.69E-01 3.92E-01 3.93E-01 3.57E-01 3.98E-01 3.76E-01 3.63E-01 3.74E-01 3.68E-01 3.55E-01 4.80E-01 4.69E-01 4.87E-01 1.92E-02 5.40E-01 4.35E-01 4.79E-01 1.48E-02 5.20E-01 4.39E-01 4.69E-01 2.41E-02 5.36E-01 4.03E-01 4.36E-01 1.80E-02 4.85E-01 3.87E-01 3.82E-01 1.78E-02 4.31E-01 3.33E-01 4.77E-01 8.23E-03 5.00E-01 4.55E-01 2.00E-01 PASS 4.71E-01 9.55E-03 4.97E-01 4.45E-01 1.20E-01 PASS 4.51E-01 9.94E-03 4.79E-01 4.24E-01 1.10E-01 PASS 4.20E-01 9.50E-03 4.46E-01 3.94E-01 7.00E-02 PASS 3.67E-01 8.53E-03 3.91E-01 3.44E-01 1.00E-02 PASS An ISO 9001:2000 Certified Company 48 RLAT Report 08-402 090317 R1.1 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (-KTL) Biased 6.00E-01 Positive Slew Rate CH B (V/µs) 5.00E-01 4.00E-01 3.00E-01 2.00E-01 1.00E-01 0.00E+00 0 50 100 150 Total Dose (krad(Si)) Figure 5.22. Plot of positive slew rate for channel B versus total dose. The data show a moderate decrease with total dose, however not sufficient to fall below the specification, even after application of the KTL statistics. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black lines show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray lines show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed lines are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2000 Certified Company 49 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 08-402 090317 R1.1 Table 5.22. Raw data of the positive slew rate for channel B versus total dose, including the statistical analysis, the specification and the status of the testing (pass/fail). Total Dose (krad(Si)) Positive Slew Rate CH B (V/µs) Device 1090 1092 1093 1094 1095 1096 1097 1098 1099 1100 1106 1113 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status 0 5.10E-01 5.35E-01 5.20E-01 4.82E-01 5.27E-01 5.07E-01 4.89E-01 5.02E-01 5.23E-01 5.04E-01 5.18E-01 5.05E-01 20 5.11E-01 5.24E-01 5.07E-01 4.77E-01 5.27E-01 5.08E-01 4.81E-01 4.99E-01 4.99E-01 4.98E-01 5.13E-01 5.11E-01 50 4.88E-01 5.07E-01 4.99E-01 4.57E-01 5.12E-01 4.86E-01 4.59E-01 4.86E-01 4.75E-01 4.76E-01 5.07E-01 5.14E-01 100 4.54E-01 4.76E-01 4.69E-01 4.21E-01 4.78E-01 4.49E-01 4.27E-01 4.50E-01 4.45E-01 4.45E-01 5.15E-01 5.02E-01 200 4.07E-01 4.21E-01 4.17E-01 3.77E-01 4.29E-01 3.99E-01 3.84E-01 3.96E-01 3.87E-01 3.84E-01 5.04E-01 5.14E-01 5.15E-01 2.05E-02 5.71E-01 4.59E-01 5.09E-01 1.99E-02 5.64E-01 4.55E-01 4.93E-01 2.19E-02 5.53E-01 4.33E-01 4.60E-01 2.35E-02 5.24E-01 3.95E-01 4.10E-01 2.02E-02 4.66E-01 3.55E-01 5.05E-01 1.22E-02 5.38E-01 4.72E-01 2.00E-01 PASS 4.97E-01 9.82E-03 5.24E-01 4.70E-01 1.20E-01 PASS 4.76E-01 1.11E-02 5.07E-01 4.46E-01 1.10E-01 PASS 4.43E-01 9.34E-03 4.69E-01 4.18E-01 7.00E-02 PASS 3.90E-01 7.04E-03 4.09E-01 3.71E-01 1.00E-02 PASS An ISO 9001:2000 Certified Company 50 RLAT Report 08-402 090317 R1.1 Average Biased Average Un-Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (+KTL) Biased 0.00E+00 Negative Slew Rate CH A (V/µs) -1.00E-01 -2.00E-01 -3.00E-01 -4.00E-01 -5.00E-01 -6.00E-01 0 50 100 150 Total Dose (krad(Si)) Figure 5.23. Plot of negative slew rate for channel A versus total dose. The data show a moderate increase with total dose, however not sufficient to exceed the specification, even after application of the KTL statistics. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black lines show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray lines show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed lines are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2000 Certified Company 51 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 08-402 090317 R1.1 Table 5.23. Raw data of the negative slew rate for channel A versus total dose, including the statistical analysis, the specification and the status of the testing (pass/fail). Total Dose (krad(Si)) Negative Slew Rate CH A (V/µs) Device 1090 1092 1093 1094 1095 1096 1097 1098 1099 1100 1106 1113 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MAX Status 0 -5.38E-01 -5.67E-01 -5.73E-01 -5.10E-01 -5.65E-01 -5.35E-01 -5.32E-01 -5.40E-01 -5.51E-01 -5.37E-01 -5.53E-01 -5.39E-01 20 -5.26E-01 -5.67E-01 -5.43E-01 -4.97E-01 -5.71E-01 -5.39E-01 -5.14E-01 -5.40E-01 -5.32E-01 -5.22E-01 -5.50E-01 -5.49E-01 50 -5.21E-01 -5.41E-01 -5.29E-01 -4.89E-01 -5.38E-01 -5.06E-01 -4.94E-01 -5.22E-01 -5.28E-01 -5.13E-01 -5.56E-01 -5.37E-01 100 -4.83E-01 -5.00E-01 -5.05E-01 -4.44E-01 -5.14E-01 -4.84E-01 -4.60E-01 -4.91E-01 -4.81E-01 -4.68E-01 -5.39E-01 -5.37E-01 200 -4.17E-01 -4.44E-01 -4.49E-01 -3.99E-01 -4.52E-01 -4.23E-01 -4.09E-01 -4.22E-01 -4.04E-01 -3.99E-01 -5.40E-01 -5.41E-01 -5.51E-01 2.64E-02 -4.78E-01 -6.23E-01 -5.41E-01 3.06E-02 -4.57E-01 -6.25E-01 -5.24E-01 2.09E-02 -4.66E-01 -5.81E-01 -4.89E-01 2.77E-02 -4.13E-01 -5.65E-01 -4.32E-01 2.32E-02 -3.69E-01 -4.96E-01 -5.39E-01 7.31E-03 -5.19E-01 -5.59E-01 -2.00E-01 PASS -5.29E-01 1.12E-02 -4.99E-01 -5.60E-01 -1.20E-01 PASS -5.13E-01 1.34E-02 -4.76E-01 -5.49E-01 -1.10E-01 PASS -4.77E-01 1.26E-02 -4.42E-01 -5.11E-01 -7.00E-02 PASS -4.11E-01 1.07E-02 -3.82E-01 -4.41E-01 -1.00E-02 PASS An ISO 9001:2000 Certified Company 52 RLAT Report 08-402 090317 R1.1 Average Biased Average Un-Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (+KTL) Biased 0.00E+00 Negative Slew Rate CH B (V/µs) -1.00E-01 -2.00E-01 -3.00E-01 -4.00E-01 -5.00E-01 -6.00E-01 -7.00E-01 0 50 100 150 Total Dose (krad(Si)) Figure 5.24. Plot of negative slew rate for channel B versus total dose. The data show a moderate increase with total dose, however not sufficient to exceed the specification, even after application of the KTL statistics. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black lines show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray lines show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed lines are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2000 Certified Company 53 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 08-402 090317 R1.1 Table 5.24. Raw data of the negative slew rate for channel B versus total dose, including the statistical analysis, the specification and the status of the testing (pass/fail). Total Dose (krad(Si)) Negative Slew Rate CH B (V/µs) Device 1090 1092 1093 1094 1095 1096 1097 1098 1099 1100 1106 1113 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MAX Status 0 -5.71E-01 -5.87E-01 -5.75E-01 -5.36E-01 -5.97E-01 -5.55E-01 -5.55E-01 -5.48E-01 -5.62E-01 -5.67E-01 -5.78E-01 -5.79E-01 20 -5.66E-01 -5.80E-01 -5.66E-01 -5.40E-01 -5.84E-01 -5.79E-01 -5.40E-01 -5.58E-01 -5.63E-01 -5.59E-01 -5.70E-01 -5.63E-01 50 -5.64E-01 -5.80E-01 -5.53E-01 -5.26E-01 -6.06E-01 -5.48E-01 -5.25E-01 -5.35E-01 -5.42E-01 -5.33E-01 -5.82E-01 -5.81E-01 100 -5.33E-01 -5.32E-01 -5.37E-01 -4.82E-01 -5.58E-01 -5.07E-01 -4.96E-01 -5.21E-01 -5.08E-01 -4.97E-01 -5.69E-01 -5.85E-01 200 -4.51E-01 -4.82E-01 -4.74E-01 -4.30E-01 -4.96E-01 -4.50E-01 -4.34E-01 -4.47E-01 -4.48E-01 -4.37E-01 -5.98E-01 -5.72E-01 -5.73E-01 2.32E-02 -5.10E-01 -6.37E-01 -5.67E-01 1.72E-02 -5.20E-01 -6.14E-01 -5.66E-01 2.99E-02 -4.84E-01 -6.48E-01 -5.28E-01 2.80E-02 -4.52E-01 -6.05E-01 -4.67E-01 2.62E-02 -3.95E-01 -5.38E-01 -5.57E-01 7.30E-03 -5.37E-01 -5.77E-01 -2.00E-01 PASS -5.60E-01 1.39E-02 -5.22E-01 -5.98E-01 -1.20E-01 PASS -5.37E-01 8.79E-03 -5.12E-01 -5.61E-01 -1.10E-01 PASS -5.06E-01 1.01E-02 -4.78E-01 -5.34E-01 -7.00E-02 PASS -4.43E-01 7.19E-03 -4.23E-01 -4.63E-01 -1.00E-02 PASS An ISO 9001:2000 Certified Company 54 RLAT Report 08-402 090317 R1.1 Average Biased Average Un-Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (+KTL) Biased Positive Supply Current @ VS=5V (A) 1.20E-03 1.00E-03 8.00E-04 6.00E-04 4.00E-04 2.00E-04 0.00E+00 0 50 100 150 Total Dose (krad(Si)) Figure 5.25. Plot of positive supply current at 5V versus total dose. The data show a slight decrease (improvement) with total dose. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the unbiased sample. The black line(s) show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray line(s) show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed line(s) are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2000 Certified Company 55 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 08-402 090317 R1.1 Table 5.25. Raw data of the positive supply current at 5V versus total dose, including the statistical analysis, the specification and the status of the testing (pass/fail). Total Dose (krad(Si)) Positive Supply Current @ VS=5V (A) Device 1090 1092 1093 1094 1095 1096 1097 1098 1099 1100 1106 1113 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MAX Status 0 6.62E-04 6.81E-04 6.60E-04 6.57E-04 6.94E-04 6.81E-04 6.70E-04 6.55E-04 6.86E-04 6.93E-04 6.61E-04 6.99E-04 20 6.74E-04 6.86E-04 6.69E-04 6.67E-04 6.97E-04 7.03E-04 6.89E-04 6.79E-04 7.02E-04 7.09E-04 6.61E-04 6.98E-04 50 6.35E-04 6.47E-04 6.31E-04 6.26E-04 6.57E-04 6.63E-04 6.46E-04 6.39E-04 6.62E-04 6.66E-04 6.63E-04 6.98E-04 100 5.58E-04 5.70E-04 5.61E-04 5.53E-04 5.83E-04 5.89E-04 5.76E-04 5.72E-04 5.83E-04 5.81E-04 6.61E-04 6.97E-04 200 4.56E-04 4.65E-04 4.61E-04 4.60E-04 4.80E-04 4.75E-04 4.73E-04 4.56E-04 4.62E-04 4.66E-04 6.60E-04 6.97E-04 6.71E-04 1.60E-05 7.15E-04 6.27E-04 6.79E-04 1.27E-05 7.13E-04 6.44E-04 6.39E-04 1.26E-05 6.74E-04 6.05E-04 5.65E-04 1.18E-05 5.97E-04 5.33E-04 4.64E-04 9.29E-06 4.90E-04 4.39E-04 6.77E-04 1.49E-05 7.18E-04 6.36E-04 1.00E-03 PASS 6.96E-04 1.22E-05 7.30E-04 6.63E-04 1.00E-03 PASS 6.55E-04 1.19E-05 6.88E-04 6.22E-04 1.00E-03 PASS 5.80E-04 6.53E-06 5.98E-04 5.62E-04 1.00E-03 PASS 4.66E-04 7.83E-06 4.88E-04 4.45E-04 1.00E-03 PASS An ISO 9001:2000 Certified Company 56 RLAT Report 08-402 090317 R1.1 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (-KTL) Biased Negative Supply Current @ VS=5V (A) 0.00E+00 -2.00E-04 -4.00E-04 -6.00E-04 -8.00E-04 -1.00E-03 -1.20E-03 0 50 100 150 Total Dose (krad(Si)) Figure 5.26. Plot of the negative supply current at 5V versus total dose. The data show a slight increase (improvement) with total dose. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the unbiased sample. The black line(s) show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray line(s) show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed line(s) are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2000 Certified Company 57 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 08-402 090317 R1.1 Table 5.26. Raw data of the negative supply current at 5V versus total dose, including the statistical analysis, the specification and the status of the testing (pass/fail). Total Dose (krad(Si)) Negative Supply Current @ VS=5V (A) Device 1090 1092 1093 1094 1095 1096 1097 1098 1099 1100 1106 1113 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status 0 -6.47E-04 -6.64E-04 -6.45E-04 -6.41E-04 -6.78E-04 -6.64E-04 -6.53E-04 -6.43E-04 -6.71E-04 -6.79E-04 -6.45E-04 -6.84E-04 20 -6.56E-04 -6.68E-04 -6.51E-04 -6.50E-04 -6.81E-04 -6.90E-04 -6.72E-04 -6.63E-04 -6.87E-04 -6.95E-04 -6.47E-04 -6.83E-04 50 -6.18E-04 -6.30E-04 -6.17E-04 -6.10E-04 -6.42E-04 -6.46E-04 -6.33E-04 -6.23E-04 -6.46E-04 -6.52E-04 -6.47E-04 -6.83E-04 100 -5.42E-04 -5.54E-04 -5.45E-04 -5.39E-04 -5.69E-04 -5.70E-04 -5.58E-04 -5.52E-04 -5.65E-04 -5.69E-04 -6.44E-04 -6.83E-04 200 -4.37E-04 -4.50E-04 -4.44E-04 -4.43E-04 -4.63E-04 -4.60E-04 -4.56E-04 -4.37E-04 -4.49E-04 -4.54E-04 -6.44E-04 -6.81E-04 -6.55E-04 1.56E-05 -6.12E-04 -6.98E-04 -6.61E-04 1.32E-05 -6.25E-04 -6.97E-04 -6.23E-04 1.26E-05 -5.89E-04 -6.58E-04 -5.50E-04 1.21E-05 -5.17E-04 -5.83E-04 -4.47E-04 9.86E-06 -4.20E-04 -4.74E-04 -6.62E-04 1.43E-05 -6.23E-04 -7.01E-04 -1.00E-03 PASS -6.81E-04 1.34E-05 -6.45E-04 -7.18E-04 -1.00E-03 PASS -6.40E-04 1.18E-05 -6.08E-04 -6.72E-04 -1.00E-03 PASS -5.63E-04 7.66E-06 -5.42E-04 -5.84E-04 -1.00E-03 PASS -4.51E-04 8.87E-06 -4.27E-04 -4.76E-04 -1.00E-03 PASS An ISO 9001:2000 Certified Company 58 RLAT Report 08-402 090317 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Input Offset Voltage CH A @ VS=5V (V) 1.00E-03 8.00E-04 6.00E-04 4.00E-04 2.00E-04 0.00E+00 -2.00E-04 -4.00E-04 -6.00E-04 -8.00E-04 -1.00E-03 0 50 100 150 200 Total Dose (krad(Si)) Figure 5.27. Plot of input offset voltage at 5V for channel A versus total dose. The data show a slight increase with total dose, however not sufficient for the parameter to exceed specification, including after application of the KTL statistics. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black line(s) show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray line(s) show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed line(s) are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2000 Certified Company 59 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 08-402 090317 R1.1 Table 5.27. Raw data of the input offset voltage at 5V for channel A versus total dose, including the statistical analysis, the specification and the status of the testing (pass/fail). Total Dose (krad(Si)) Input Offset Voltage CH A @ VS=5V (V) Device 1090 1092 1093 1094 1095 1096 1097 1098 1099 1100 1106 1113 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status 0 -4.81E-05 -1.11E-05 4.76E-05 -4.37E-05 -7.52E-05 2.34E-05 5.19E-06 -4.49E-05 -7.14E-05 -8.94E-06 6.99E-05 -4.38E-05 20 -4.00E-05 -1.21E-06 5.64E-05 -2.69E-05 -6.97E-05 3.98E-05 2.50E-05 -2.69E-05 -5.29E-05 9.54E-06 6.97E-05 -4.25E-05 50 -1.55E-05 2.19E-05 7.61E-05 4.83E-06 -5.29E-05 7.49E-05 6.27E-05 1.21E-07 -1.26E-05 4.65E-05 7.09E-05 -4.25E-05 100 2.58E-05 5.46E-05 1.02E-04 6.86E-05 -2.35E-05 1.23E-04 1.34E-04 4.55E-05 6.13E-05 1.19E-04 6.83E-05 -4.27E-05 200 1.09E-04 1.18E-04 1.52E-04 1.78E-04 3.63E-05 2.25E-04 2.62E-04 1.37E-04 2.06E-04 2.77E-04 6.87E-05 -4.37E-05 -2.61E-05 4.71E-05 1.03E-04 -1.55E-04 -1.63E-05 4.75E-05 1.14E-04 -1.47E-04 6.88E-06 4.77E-05 1.38E-04 -1.24E-04 4.55E-05 4.73E-05 1.75E-04 -8.43E-05 1.19E-04 5.35E-05 2.65E-04 -2.81E-05 -1.93E-05 3.84E-05 8.60E-05 -1.25E-04 -4.50E-04 PASS 4.50E-04 PASS -1.09E-06 3.81E-05 1.03E-04 -1.06E-04 -6.00E-04 PASS 6.00E-04 PASS 3.43E-05 3.86E-05 1.40E-04 -7.15E-05 -7.50E-04 PASS 7.50E-04 PASS 9.66E-05 4.02E-05 2.07E-04 -1.36E-05 -9.00E-04 PASS 9.00E-04 PASS 2.21E-04 5.50E-05 3.72E-04 7.05E-05 -9.00E-04 PASS 9.00E-04 PASS An ISO 9001:2000 Certified Company 60 RLAT Report 08-402 090317 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Input Offset Voltage CH B @ VS=5V (V) 1.00E-03 8.00E-04 6.00E-04 4.00E-04 2.00E-04 0.00E+00 -2.00E-04 -4.00E-04 -6.00E-04 -8.00E-04 -1.00E-03 0 50 100 150 Total Dose (krad(Si)) Figure 5.28. Plot of input offset voltage at 5V for channel B versus total dose. The data show a slight increase with total dose, however not sufficient for the parameter to exceed specification, including after application of the KTL statistics. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black line(s) show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray line(s) show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed line(s) are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2000 Certified Company 61 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 08-402 090317 R1.1 Table 5.28. Raw data of the input offset voltage at 5V for channel B versus total dose, including the statistical analysis, the specification and the status of the testing (pass/fail). Total Dose (krad(Si)) Input Offset Voltage CH B @ VS=5V (V) Device 1090 1092 1093 1094 1095 1096 1097 1098 1099 1100 1106 1113 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status 0 2.49E-05 -1.92E-05 -3.71E-05 -4.35E-06 -6.98E-05 9.42E-06 3.74E-06 -2.04E-05 -5.34E-05 -7.62E-05 1.15E-05 -2.52E-05 20 3.51E-05 -8.09E-06 -3.44E-05 7.12E-06 -6.24E-05 2.97E-05 3.34E-05 -3.98E-06 -2.72E-05 -5.24E-05 1.07E-05 -2.51E-05 50 6.54E-05 8.45E-06 -2.05E-05 4.09E-05 -3.65E-05 6.75E-05 7.30E-05 2.75E-05 7.97E-06 -1.33E-05 1.07E-05 -2.54E-05 100 1.12E-04 3.75E-05 1.01E-05 9.40E-05 -7.85E-06 1.41E-04 1.57E-04 9.15E-05 8.03E-05 6.60E-05 1.06E-05 -2.58E-05 200 1.99E-04 9.01E-05 4.83E-05 2.04E-04 4.91E-05 2.63E-04 3.01E-04 1.93E-04 2.26E-04 2.29E-04 1.17E-05 -2.47E-05 -2.11E-05 3.54E-05 7.61E-05 -1.18E-04 -1.25E-05 3.76E-05 9.05E-05 -1.16E-04 1.16E-05 4.22E-05 1.27E-04 -1.04E-04 4.92E-05 5.22E-05 1.92E-04 -9.39E-05 1.18E-04 7.80E-05 3.32E-04 -9.59E-05 -2.74E-05 3.68E-05 7.37E-05 -1.28E-04 -4.50E-04 PASS 4.50E-04 PASS -4.08E-06 3.68E-05 9.68E-05 -1.05E-04 -6.00E-04 PASS 6.00E-04 PASS 3.25E-05 3.74E-05 1.35E-04 -7.00E-05 -7.50E-04 PASS 7.50E-04 PASS 1.07E-04 3.95E-05 2.15E-04 -1.25E-06 -9.00E-04 PASS 9.00E-04 PASS 2.42E-04 4.11E-05 3.55E-04 1.30E-04 -9.00E-04 PASS 9.00E-04 PASS An ISO 9001:2000 Certified Company 62 RLAT Report 08-402 090317 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 2.50E-08 Input Offset Current CH A @ VS=5V (V) 2.00E-08 1.50E-08 1.00E-08 5.00E-09 0.00E+00 -5.00E-09 -1.00E-08 -1.50E-08 -2.00E-08 -2.50E-08 0 50 100 150 Total Dose (krad(Si)) Figure 5.29. Plot of input offset current at 5V for channel A versus total dose. The data show a very slight increase with total dose, however not sufficient for the parameter to exceed specification, including after application of the KTL statistics. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black line(s) show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray line(s) show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed line(s) are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2000 Certified Company 63 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 08-402 090317 R1.1 Table 5.29. Raw data of input offset current at 5V for channel A versus total dose, including the statistical analysis, the specification and the status of the testing (pass/fail). Total Dose (krad(Si)) Input Offset Current CH A @ VS=5V (V) Device 1090 1092 1093 1094 1095 1096 1097 1098 1099 1100 1106 1113 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status 0 7.50E-11 -6.70E-11 -5.90E-11 -1.07E-10 7.50E-11 1.00E-11 3.60E-11 -3.70E-11 -7.80E-11 1.00E-11 -2.00E-11 -1.90E-11 20 1.60E-10 -6.30E-11 6.10E-11 -3.50E-11 5.10E-11 3.60E-11 6.40E-11 0.00E+00 -4.40E-11 6.60E-11 -1.21E-10 0.00E+00 50 1.47E-10 1.18E-10 2.01E-10 3.98E-10 2.22E-10 2.80E-10 1.32E-10 2.50E-11 1.25E-10 2.74E-10 -8.00E-12 2.40E-11 100 6.62E-10 4.24E-10 6.03E-10 9.01E-10 6.15E-10 8.99E-10 4.04E-10 3.17E-10 6.30E-10 5.00E-10 -1.13E-10 -1.00E-11 200 1.20E-09 1.23E-09 2.05E-09 2.22E-09 1.12E-09 2.47E-09 1.53E-09 1.47E-09 2.49E-09 1.40E-09 -1.21E-10 -2.40E-11 -1.66E-11 8.56E-11 2.18E-10 -2.51E-10 3.48E-11 8.81E-11 2.76E-10 -2.07E-10 2.17E-10 1.09E-10 5.17E-10 -8.24E-11 6.41E-10 1.71E-10 1.11E-09 1.72E-10 1.56E-09 5.27E-10 3.01E-09 1.17E-10 -1.18E-11 4.54E-11 1.13E-10 -1.36E-10 -1.00E-08 PASS 1.00E-08 PASS 2.44E-11 4.67E-11 1.52E-10 -1.04E-10 -1.00E-08 PASS 1.00E-08 PASS 1.67E-10 1.09E-10 4.66E-10 -1.31E-10 -1.50E-08 PASS 1.50E-08 PASS 5.50E-10 2.27E-10 1.17E-09 -7.27E-11 -2.00E-08 PASS 2.00E-08 PASS 1.87E-09 5.58E-10 3.40E-09 3.43E-10 -2.00E-08 PASS 2.00E-08 PASS An ISO 9001:2000 Certified Company 64 RLAT Report 08-402 090317 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Input Offset Current CH B @ VS=5V (A) 2.50E-08 2.00E-08 1.50E-08 1.00E-08 5.00E-09 0.00E+00 -5.00E-09 -1.00E-08 -1.50E-08 -2.00E-08 -2.50E-08 0 50 100 150 Total Dose (krad(Si)) Figure 5.30. Plot of input offset current at 5V for channel B versus total dose. The data show a very slight increase with total dose, however not sufficient for the parameter to exceed specification, including after application of the KTL statistics. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black line(s) show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray line(s) show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed line(s) are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2000 Certified Company 65 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 08-402 090317 R1.1 Table 5.30. Raw data of input offset current at 5V for channel B versus total dose, including the statistical analysis, the specification and the status of the testing (pass/fail). Total Dose (krad(Si)) Input Offset Current CH B @ VS=5V (A) Device 1090 1092 1093 1094 1095 1096 1097 1098 1099 1100 1106 1113 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status 0 6.00E-12 7.00E-12 9.90E-11 3.80E-11 5.10E-11 1.80E-11 -1.65E-10 -6.60E-11 -1.14E-10 6.00E-12 -2.30E-11 3.90E-11 20 1.10E-11 -1.10E-10 2.46E-10 -1.50E-11 4.50E-11 -1.34E-10 -1.74E-10 -1.70E-10 -1.22E-10 -1.72E-10 -1.03E-10 1.07E-10 50 -9.10E-11 -1.05E-10 4.03E-10 1.01E-10 2.80E-11 1.22E-10 -1.46E-10 -1.94E-10 -6.80E-11 -1.43E-10 1.60E-11 7.80E-11 100 4.08E-10 2.23E-10 1.09E-09 1.01E-09 4.44E-10 7.53E-10 2.92E-10 9.80E-11 4.71E-10 6.00E-11 -1.30E-10 3.90E-11 200 1.25E-09 1.06E-09 2.58E-09 2.48E-09 1.54E-09 2.87E-09 1.99E-09 1.42E-09 2.21E-09 5.98E-10 -1.08E-10 -1.00E-11 4.02E-11 3.82E-11 1.45E-10 -6.47E-11 3.54E-11 1.31E-10 3.95E-10 -3.24E-10 6.72E-11 2.06E-10 6.33E-10 -4.98E-10 6.35E-10 3.89E-10 1.70E-09 -4.32E-10 1.78E-09 7.05E-10 3.71E-09 -1.54E-10 -6.42E-11 7.80E-11 1.50E-10 -2.78E-10 -1.00E-08 PASS 1.00E-08 PASS -1.54E-10 2.45E-11 -8.72E-11 -2.22E-10 -1.00E-08 PASS 1.00E-08 PASS -8.58E-11 1.25E-10 2.56E-10 -4.27E-10 -1.50E-08 PASS 1.50E-08 PASS 3.35E-10 2.86E-10 1.12E-09 -4.49E-10 -2.00E-08 PASS 2.00E-08 PASS 1.82E-09 8.58E-10 4.17E-09 -5.35E-10 -2.00E-08 PASS 2.00E-08 PASS An ISO 9001:2000 Certified Company 66 RLAT Report 08-402 090317 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX '+ Input Bias Current CH A @ VS=5V (A) 2.50E-07 2.00E-07 1.50E-07 1.00E-07 5.00E-08 0.00E+00 -5.00E-08 -1.00E-07 -1.50E-07 -2.00E-07 -2.50E-07 0 50 100 150 Total Dose (krad(Si)) Figure 5.31. Plot of input bias current, non-inverting input at 5V for channel A versus total dose. The data show an increase with total dose, however not sufficient for the parameter to exceed specification, including after application of the KTL statistics. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black line(s) show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray line(s) show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed line(s) are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2000 Certified Company 67 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 08-402 090317 R1.1 Table 5.31. Raw data of input bias current, non-inverting input at 5V for channel A versus total dose, including the statistical analysis, the specification and the status of the testing (pass/fail). Total Dose (krad(Si)) + Input Bias Current CH A @ VS=5V (A) Device 1090 1092 1093 1094 1095 1096 1097 1098 1099 1100 1106 1113 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status 0 1.16E-08 1.16E-08 1.11E-08 1.24E-08 1.20E-08 1.18E-08 1.23E-08 1.20E-08 1.23E-08 1.15E-08 1.18E-08 1.21E-08 20 1.57E-08 1.58E-08 1.50E-08 1.67E-08 1.62E-08 1.56E-08 1.65E-08 1.62E-08 1.63E-08 1.54E-08 1.18E-08 1.21E-08 50 2.39E-08 2.38E-08 2.26E-08 2.49E-08 2.43E-08 2.28E-08 2.39E-08 2.38E-08 2.40E-08 2.30E-08 1.18E-08 1.21E-08 100 3.67E-08 3.66E-08 3.43E-08 3.80E-08 3.73E-08 3.44E-08 3.59E-08 3.62E-08 3.64E-08 3.52E-08 1.17E-08 1.21E-08 200 5.89E-08 5.98E-08 5.48E-08 6.08E-08 6.02E-08 5.44E-08 5.63E-08 5.66E-08 5.65E-08 5.58E-08 1.18E-08 1.21E-08 1.17E-08 4.98E-10 1.31E-08 1.04E-08 1.59E-08 6.25E-10 1.76E-08 1.42E-08 2.39E-08 8.53E-10 2.62E-08 2.16E-08 3.66E-08 1.41E-09 4.04E-08 3.27E-08 5.89E-08 2.38E-09 6.54E-08 5.24E-08 1.20E-08 3.49E-10 1.29E-08 1.10E-08 -5.00E-08 PASS 5.00E-08 PASS 1.60E-08 4.50E-10 1.72E-08 1.48E-08 -1.00E-07 PASS 1.00E-07 PASS 2.35E-08 5.60E-10 2.50E-08 2.20E-08 -1.25E-07 PASS 1.25E-07 PASS 3.56E-08 8.20E-10 3.79E-08 3.34E-08 -2.00E-07 PASS 2.00E-07 PASS 5.59E-08 8.89E-10 5.83E-08 5.35E-08 -2.00E-07 PASS 2.00E-07 PASS An ISO 9001:2000 Certified Company 68 RLAT Report 08-402 090317 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX + Input Bias Current CH B @ VS=5V (A) 2.50E-07 2.00E-07 1.50E-07 1.00E-07 5.00E-08 0.00E+00 -5.00E-08 -1.00E-07 -1.50E-07 -2.00E-07 -2.50E-07 0 50 100 150 Total Dose (krad(Si)) Figure 5.32. Plot of input bias current, non-inverting input at 5V for channel B versus total dose. The data show a slight increase with total dose, however not sufficient for the parameter to exceed specification, including after application of the KTL statistics. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black line(s) show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray line(s) show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed line(s) are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2000 Certified Company 69 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 08-402 090317 R1.1 Table 5.32. Raw data of input bias current, non-inverting input at 5V for channel B versus total dose, including the statistical analysis, the specification and the status of the testing (pass/fail). Total Dose (krad(Si)) + Input Bias Current CH B @ VS=5V (A) Device 1090 1092 1093 1094 1095 1096 1097 1098 1099 1100 1106 1113 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status 0 1.20E-08 1.20E-08 1.21E-08 1.29E-08 1.26E-08 1.27E-08 1.29E-08 1.24E-08 1.28E-08 1.26E-08 1.23E-08 1.20E-08 20 1.62E-08 1.64E-08 1.63E-08 1.74E-08 1.70E-08 1.70E-08 1.72E-08 1.68E-08 1.69E-08 1.69E-08 1.22E-08 1.19E-08 50 2.47E-08 2.48E-08 2.44E-08 2.59E-08 2.55E-08 2.48E-08 2.49E-08 2.47E-08 2.50E-08 2.50E-08 1.23E-08 1.20E-08 100 3.77E-08 3.82E-08 3.68E-08 3.93E-08 3.90E-08 3.71E-08 3.73E-08 3.75E-08 3.78E-08 3.79E-08 1.22E-08 1.19E-08 200 6.02E-08 6.18E-08 5.84E-08 6.25E-08 6.24E-08 5.83E-08 5.82E-08 5.83E-08 5.86E-08 5.94E-08 1.22E-08 1.19E-08 1.23E-08 4.13E-10 1.35E-08 1.12E-08 1.66E-08 5.22E-10 1.81E-08 1.52E-08 2.51E-08 6.39E-10 2.68E-08 2.33E-08 3.82E-08 1.01E-09 4.10E-08 3.55E-08 6.11E-08 1.72E-09 6.58E-08 5.63E-08 1.27E-08 1.88E-10 1.32E-08 1.22E-08 -5.00E-08 PASS 5.00E-08 PASS 1.70E-08 1.60E-10 1.74E-08 1.65E-08 -1.00E-07 PASS 1.00E-07 PASS 2.49E-08 1.15E-10 2.52E-08 2.46E-08 -1.25E-07 PASS 1.25E-07 PASS 3.75E-08 3.29E-10 3.84E-08 3.66E-08 -2.00E-07 PASS 2.00E-07 PASS 5.86E-08 4.98E-10 5.99E-08 5.72E-08 -2.00E-07 PASS 2.00E-07 PASS An ISO 9001:2000 Certified Company 70 RLAT Report 08-402 090317 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX - Input Bias Current CH A @ VS=5V (A) 2.50E-07 2.00E-07 1.50E-07 1.00E-07 5.00E-08 0.00E+00 -5.00E-08 -1.00E-07 -1.50E-07 -2.00E-07 -2.50E-07 0 50 100 150 Total Dose (krad(Si)) Figure 5.33. Plot of input bias current, inverting input at 5V for channel A versus total dose. The data show a slight increase with total dose, however not sufficient for the parameter to exceed specification, including after application of the KTL statistics. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black line(s) show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray line(s) show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed line(s) are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2000 Certified Company 71 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 08-402 090317 R1.1 Table 5.33. Raw data of the input bias current, inverting input at 5V for channel A versus total dose, including the statistical analysis, the specification and the status of the testing (pass/fail). Total Dose (krad(Si)) - Input Bias Current CH A @ VS=5V (A) Device 1090 1092 1093 1094 1095 1096 1097 1098 1099 1100 1106 1113 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status 0 1.16E-08 1.17E-08 1.12E-08 1.25E-08 1.21E-08 1.17E-08 1.25E-08 1.21E-08 1.22E-08 1.15E-08 1.18E-08 1.24E-08 20 1.59E-08 1.59E-08 1.52E-08 1.68E-08 1.64E-08 1.57E-08 1.67E-08 1.62E-08 1.63E-08 1.56E-08 1.19E-08 1.23E-08 50 2.43E-08 2.40E-08 2.29E-08 2.54E-08 2.46E-08 2.32E-08 2.41E-08 2.40E-08 2.43E-08 2.33E-08 1.18E-08 1.23E-08 100 3.74E-08 3.73E-08 3.50E-08 3.90E-08 3.82E-08 3.54E-08 3.65E-08 3.68E-08 3.73E-08 3.58E-08 1.17E-08 1.22E-08 200 6.04E-08 6.12E-08 5.70E-08 6.32E-08 6.16E-08 5.70E-08 5.80E-08 5.81E-08 5.91E-08 5.73E-08 1.17E-08 1.21E-08 1.18E-08 4.90E-10 1.32E-08 1.05E-08 1.60E-08 6.13E-10 1.77E-08 1.44E-08 2.42E-08 9.04E-10 2.67E-08 2.17E-08 3.74E-08 1.49E-09 4.15E-08 3.33E-08 6.07E-08 2.28E-09 6.69E-08 5.44E-08 1.20E-08 4.03E-10 1.31E-08 1.09E-08 -5.00E-08 PASS 5.00E-08 PASS 1.61E-08 4.59E-10 1.74E-08 1.48E-08 -1.00E-07 PASS 1.00E-07 PASS 2.38E-08 5.04E-10 2.51E-08 2.24E-08 -1.25E-07 PASS 1.25E-07 PASS 3.64E-08 7.62E-10 3.85E-08 3.43E-08 -2.00E-07 PASS 2.00E-07 PASS 5.79E-08 8.19E-10 6.01E-08 5.57E-08 -2.00E-07 PASS 2.00E-07 PASS An ISO 9001:2000 Certified Company 72 RLAT Report 08-402 090317 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX - Input Bias Current CH B @ VS=5V (A) 2.50E-07 2.00E-07 1.50E-07 1.00E-07 5.00E-08 0.00E+00 -5.00E-08 -1.00E-07 -1.50E-07 -2.00E-07 -2.50E-07 0 50 100 150 Total Dose (krad(Si)) Figure 5.34. Plot of input bias current, inverting input at 5V for channel B versus total dose. The data show a slight increase with total dose, however not sufficient for the parameter to exceed specification, including after application of the KTL statistics. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black line(s) show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray line(s) show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed line(s) are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2000 Certified Company 73 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 08-402 090317 R1.1 Table 5.34. Raw data of the input bias current, inverting input at 5V for channel B versus total dose, including the statistical analysis, the specification and the status of the testing (pass/fail). Total Dose (krad(Si)) - Input Bias Current CH B @ VS=5V (A) Device 1090 1092 1093 1094 1095 1096 1097 1098 1099 1100 1106 1113 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status 0 1.20E-08 1.21E-08 1.23E-08 1.30E-08 1.26E-08 1.27E-08 1.29E-08 1.25E-08 1.27E-08 1.26E-08 1.23E-08 1.21E-08 20 1.63E-08 1.64E-08 1.66E-08 1.75E-08 1.71E-08 1.70E-08 1.72E-08 1.66E-08 1.70E-08 1.69E-08 1.23E-08 1.21E-08 50 2.47E-08 2.48E-08 2.49E-08 2.62E-08 2.56E-08 2.50E-08 2.50E-08 2.45E-08 2.50E-08 2.48E-08 1.22E-08 1.21E-08 100 3.82E-08 3.86E-08 3.81E-08 4.04E-08 3.97E-08 3.80E-08 3.77E-08 3.78E-08 3.85E-08 3.82E-08 1.23E-08 1.21E-08 200 6.17E-08 6.30E-08 6.13E-08 6.53E-08 6.41E-08 6.11E-08 6.04E-08 5.98E-08 6.10E-08 6.03E-08 1.23E-08 1.20E-08 1.24E-08 4.15E-10 1.36E-08 1.13E-08 1.68E-08 5.14E-10 1.82E-08 1.54E-08 2.52E-08 6.29E-10 2.70E-08 2.35E-08 3.90E-08 1.02E-09 4.18E-08 3.62E-08 6.31E-08 1.66E-09 6.76E-08 5.85E-08 1.27E-08 1.39E-10 1.31E-08 1.23E-08 -5.00E-08 PASS 5.00E-08 PASS 1.69E-08 2.08E-10 1.75E-08 1.64E-08 -1.00E-07 PASS 1.00E-07 PASS 2.48E-08 1.87E-10 2.54E-08 2.43E-08 -1.25E-07 PASS 1.25E-07 PASS 3.80E-08 2.95E-10 3.88E-08 3.72E-08 -2.00E-07 PASS 2.00E-07 PASS 6.05E-08 5.35E-10 6.20E-08 5.90E-08 -2.00E-07 PASS 2.00E-07 PASS An ISO 9001:2000 Certified Company 74 Output Voltage High, No Load CH A @ VS=5V (V) RLAT Report 08-402 090317 R1.1 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (-KTL) Biased 4.35E+00 4.30E+00 4.25E+00 4.20E+00 4.15E+00 4.10E+00 4.05E+00 4.00E+00 3.95E+00 0 50 100 150 Total Dose (krad(Si)) Figure 5.35. Plot of the output voltage high (no load) at 5V for channel A versus total dose. The data show only a slight change with total dose, however not sufficient for the parameter to fall below specification, including after application of the KTL statistics. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black line(s) show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray line(s) show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed line(s) are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2000 Certified Company 75 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 08-402 090317 R1.1 Table 5.35. Raw data of output voltage high (no load) at 5V for channel A versus total dose, including the statistical analysis, the specification and the status of the testing (pass/fail). Total Dose (krad(Si)) Output Voltage High, No Load CH A @ VS=5V (V) Device 1090 1092 1093 1094 1095 1096 1097 1098 1099 1100 1106 1113 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status 0 4.28E+00 4.28E+00 4.28E+00 4.28E+00 4.28E+00 4.28E+00 4.28E+00 4.28E+00 4.27E+00 4.27E+00 4.28E+00 4.27E+00 20 4.27E+00 4.27E+00 4.27E+00 4.27E+00 4.27E+00 4.27E+00 4.26E+00 4.27E+00 4.26E+00 4.26E+00 4.28E+00 4.27E+00 50 4.29E+00 4.29E+00 4.29E+00 4.29E+00 4.29E+00 4.28E+00 4.28E+00 4.28E+00 4.28E+00 4.28E+00 4.28E+00 4.27E+00 100 4.31E+00 4.31E+00 4.31E+00 4.30E+00 4.31E+00 4.31E+00 4.30E+00 4.31E+00 4.31E+00 4.30E+00 4.28E+00 4.27E+00 200 4.31E+00 4.31E+00 4.31E+00 4.31E+00 4.31E+00 4.31E+00 4.30E+00 4.32E+00 4.31E+00 4.31E+00 4.28E+00 4.27E+00 4.28E+00 1.87E-03 4.28E+00 4.27E+00 4.27E+00 1.10E-03 4.27E+00 4.27E+00 4.29E+00 1.79E-03 4.29E+00 4.28E+00 4.31E+00 3.63E-03 4.32E+00 4.30E+00 4.31E+00 3.91E-03 4.32E+00 4.30E+00 4.28E+00 4.60E-03 4.29E+00 4.26E+00 4.00E+00 PASS 4.26E+00 3.70E-03 4.27E+00 4.25E+00 4.00E+00 PASS 4.28E+00 2.49E-03 4.28E+00 4.27E+00 4.00E+00 PASS 4.31E+00 5.63E-03 4.32E+00 4.29E+00 4.00E+00 PASS 4.31E+00 5.36E-03 4.32E+00 4.29E+00 4.00E+00 PASS An ISO 9001:2000 Certified Company 76 RLAT Report 08-402 090317 R1.1 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (-KTL) Biased Output Voltage High, No Load CH B @ VS=5V (V) 4.35E+00 4.30E+00 4.25E+00 4.20E+00 4.15E+00 4.10E+00 4.05E+00 4.00E+00 3.95E+00 0 50 100 150 Total Dose (krad(Si)) Figure 5.36. Plot of the output voltage high (no load) at 5V for channel B versus total dose. The data show only a slight change with total dose, however not sufficient for the parameter to fall below specification, including after application of the KTL statistics. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black line(s) show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray line(s) show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed line(s) are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2000 Certified Company 77 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 08-402 090317 R1.1 Table 5.36. Raw data of output voltage high (no load) at 5V for channel B versus total dose, including the statistical analysis, the specification and the status of the testing (pass/fail). Total Dose (krad(Si)) Output Voltage High, No Load CH B @ VS=5V (V) Device 1090 1092 1093 1094 1095 1096 1097 1098 1099 1100 1106 1113 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status 0 4.27E+00 4.26E+00 4.27E+00 4.26E+00 4.26E+00 4.26E+00 4.26E+00 4.27E+00 4.26E+00 4.26E+00 4.27E+00 4.26E+00 20 4.26E+00 4.26E+00 4.26E+00 4.26E+00 4.26E+00 4.25E+00 4.25E+00 4.26E+00 4.25E+00 4.25E+00 4.27E+00 4.25E+00 50 4.27E+00 4.27E+00 4.27E+00 4.27E+00 4.27E+00 4.26E+00 4.26E+00 4.26E+00 4.26E+00 4.26E+00 4.27E+00 4.25E+00 100 4.31E+00 4.31E+00 4.31E+00 4.30E+00 4.31E+00 4.30E+00 4.30E+00 4.29E+00 4.30E+00 4.30E+00 4.27E+00 4.25E+00 200 4.31E+00 4.32E+00 4.31E+00 4.31E+00 4.31E+00 4.31E+00 4.31E+00 4.32E+00 4.31E+00 4.31E+00 4.27E+00 4.25E+00 4.26E+00 3.44E-03 4.27E+00 4.25E+00 4.26E+00 2.61E-03 4.26E+00 4.25E+00 4.27E+00 2.30E-03 4.28E+00 4.26E+00 4.31E+00 4.09E-03 4.32E+00 4.30E+00 4.31E+00 3.39E-03 4.32E+00 4.30E+00 4.26E+00 4.04E-03 4.27E+00 4.25E+00 4.00E+00 PASS 4.25E+00 3.13E-03 4.26E+00 4.24E+00 4.00E+00 PASS 4.26E+00 1.79E-03 4.27E+00 4.26E+00 4.00E+00 PASS 4.30E+00 4.69E-03 4.31E+00 4.29E+00 4.00E+00 PASS 4.31E+00 5.27E-03 4.33E+00 4.30E+00 4.00E+00 PASS An ISO 9001:2000 Certified Company 78 RLAT Report 08-402 090317 R1.1 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (-KTL) Biased Output Voltage High, 600Ω CH A @ VS=5V (V) 4.50E+00 4.00E+00 3.50E+00 3.00E+00 2.50E+00 2.00E+00 1.50E+00 1.00E+00 5.00E-01 0.00E+00 0 50 100 150 Total Dose (krad(Si)) Figure 5.37. Plot of the output voltage high (600Ω load) at 5V for channel A versus total dose. The data show no significant change with total dose. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the unbiased sample. The black line(s) show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray line(s) show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed line(s) are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2000 Certified Company 79 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 08-402 090317 R1.1 Table 5.37. Raw data of output voltage high (600Ω load) at 5V for channel A versus total dose, including the statistical analysis, the specification and the status of the testing (pass/fail). Total Dose (krad(Si)) Output Voltage High, 600Ω CH A @ VS=5V (V) Device 1090 1092 1093 1094 1095 1096 1097 1098 1099 1100 1106 1113 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status 0 3.82E+00 3.83E+00 3.83E+00 3.80E+00 3.84E+00 3.83E+00 3.81E+00 3.83E+00 3.82E+00 3.80E+00 3.83E+00 3.81E+00 20 3.82E+00 3.83E+00 3.83E+00 3.80E+00 3.84E+00 3.82E+00 3.81E+00 3.83E+00 3.82E+00 3.80E+00 3.83E+00 3.81E+00 50 3.82E+00 3.83E+00 3.83E+00 3.80E+00 3.84E+00 3.82E+00 3.80E+00 3.82E+00 3.81E+00 3.80E+00 3.83E+00 3.81E+00 100 3.81E+00 3.82E+00 3.82E+00 3.79E+00 3.83E+00 3.82E+00 3.80E+00 3.82E+00 3.81E+00 3.79E+00 3.83E+00 3.80E+00 200 3.81E+00 3.82E+00 3.82E+00 3.79E+00 3.83E+00 3.82E+00 3.79E+00 3.82E+00 3.80E+00 3.79E+00 3.83E+00 3.80E+00 3.83E+00 1.40E-02 3.86E+00 3.79E+00 3.82E+00 1.36E-02 3.86E+00 3.79E+00 3.82E+00 1.47E-02 3.86E+00 3.78E+00 3.82E+00 1.52E-02 3.86E+00 3.77E+00 3.81E+00 1.61E-02 3.86E+00 3.77E+00 3.82E+00 1.07E-02 3.85E+00 3.79E+00 3.40E+00 PASS 3.81E+00 1.06E-02 3.84E+00 3.79E+00 3.20E+00 PASS 3.81E+00 1.09E-02 3.84E+00 3.78E+00 3.00E+00 PASS 3.81E+00 1.22E-02 3.84E+00 3.77E+00 2.80E+00 PASS 3.80E+00 1.30E-02 3.84E+00 3.77E+00 2.80E+00 PASS An ISO 9001:2000 Certified Company 80 RLAT Report 08-402 090317 R1.1 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (-KTL) Biased Output Voltage High, 600Ω CH B @ VS=5V (V) 4.00E+00 3.80E+00 3.60E+00 3.40E+00 3.20E+00 3.00E+00 2.80E+00 2.60E+00 2.40E+00 2.20E+00 2.00E+00 0 50 100 150 Total Dose (krad(Si)) Figure 5.38. Plot of the output voltage high (600Ω load) at 5V for channel B versus total dose. The data show no significant change with total dose. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black line(s) show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray line(s) show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed line(s) are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2000 Certified Company 81 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 08-402 090317 R1.1 Table 5.38. Raw data of output voltage high (600Ω load) at 5V for channel B versus total dose, including the statistical analysis, the specification and the status of the testing (pass/fail). Total Dose (krad(Si)) Output Voltage High, 600Ω CH B @ VS=5V (V) Device 1090 1092 1093 1094 1095 1096 1097 1098 1099 1100 1106 1113 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status 0 3.83E+00 3.84E+00 3.84E+00 3.81E+00 3.85E+00 3.84E+00 3.82E+00 3.83E+00 3.83E+00 3.82E+00 3.84E+00 3.82E+00 20 3.83E+00 3.84E+00 3.84E+00 3.81E+00 3.85E+00 3.84E+00 3.81E+00 3.83E+00 3.83E+00 3.81E+00 3.84E+00 3.82E+00 50 3.83E+00 3.84E+00 3.84E+00 3.81E+00 3.84E+00 3.83E+00 3.81E+00 3.83E+00 3.82E+00 3.81E+00 3.84E+00 3.82E+00 100 3.82E+00 3.83E+00 3.83E+00 3.80E+00 3.84E+00 3.83E+00 3.81E+00 3.83E+00 3.82E+00 3.81E+00 3.83E+00 3.82E+00 200 3.82E+00 3.83E+00 3.83E+00 3.80E+00 3.84E+00 3.83E+00 3.80E+00 3.82E+00 3.81E+00 3.80E+00 3.83E+00 3.82E+00 3.83E+00 1.39E-02 3.87E+00 3.80E+00 3.83E+00 1.37E-02 3.87E+00 3.79E+00 3.83E+00 1.47E-02 3.87E+00 3.79E+00 3.83E+00 1.58E-02 3.87E+00 3.78E+00 3.82E+00 1.61E-02 3.86E+00 3.78E+00 3.83E+00 9.34E-03 3.85E+00 3.80E+00 3.40E+00 PASS 3.82E+00 9.89E-03 3.85E+00 3.80E+00 3.20E+00 PASS 3.82E+00 9.59E-03 3.85E+00 3.79E+00 3.00E+00 PASS 3.82E+00 1.08E-02 3.85E+00 3.79E+00 2.80E+00 PASS 3.81E+00 1.21E-02 3.85E+00 3.78E+00 2.80E+00 PASS An ISO 9001:2000 Certified Company 82 RLAT Report 08-402 090317 R1.1 Average Biased Average Un-Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (+KTL) Biased Output Voltage Low, No Load CH A @ VS=5V (V) 6.00E-02 5.00E-02 4.00E-02 3.00E-02 2.00E-02 1.00E-02 0.00E+00 0 50 100 150 Total Dose (krad(Si)) Figure 5.39. Plot of the output voltage low (no load) at 5V for channel A versus total dose. The data show no significant change with total dose. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black line(s) show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray line(s) show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed line(s) are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2000 Certified Company 83 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 08-402 090317 R1.1 Table 5.39. Raw data of output voltage low (no load) at 5V for channel A versus total dose, including the statistical analysis, the specification and the status of the testing (pass/fail). Total Dose (krad(Si)) Output Voltage Low, No Load CH A @ VS=5V (V) Device 1090 1092 1093 1094 1095 1096 1097 1098 1099 1100 1106 1113 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MAX Status 0 1.40E-02 1.41E-02 1.41E-02 1.36E-02 1.41E-02 1.37E-02 1.37E-02 1.42E-02 1.37E-02 1.36E-02 1.40E-02 1.37E-02 20 1.40E-02 1.41E-02 1.41E-02 1.37E-02 1.41E-02 1.38E-02 1.37E-02 1.41E-02 1.37E-02 1.37E-02 1.40E-02 1.35E-02 50 1.40E-02 1.41E-02 1.43E-02 1.39E-02 1.42E-02 1.39E-02 1.39E-02 1.43E-02 1.39E-02 1.39E-02 1.41E-02 1.35E-02 100 1.43E-02 1.44E-02 1.44E-02 1.40E-02 1.43E-02 1.42E-02 1.42E-02 1.46E-02 1.42E-02 1.44E-02 1.41E-02 1.36E-02 200 1.46E-02 1.46E-02 1.46E-02 1.45E-02 1.46E-02 1.50E-02 1.50E-02 1.52E-02 1.51E-02 1.53E-02 1.40E-02 1.36E-02 1.40E-02 2.17E-04 1.46E-02 1.34E-02 1.40E-02 1.73E-04 1.45E-02 1.35E-02 1.41E-02 1.58E-04 1.45E-02 1.37E-02 1.43E-02 1.64E-04 1.47E-02 1.38E-02 1.46E-02 4.47E-05 1.47E-02 1.45E-02 1.38E-02 2.39E-04 1.44E-02 1.31E-02 2.50E-02 PASS 1.38E-02 1.73E-04 1.43E-02 1.33E-02 3.00E-02 PASS 1.40E-02 1.79E-04 1.45E-02 1.35E-02 4.00E-02 PASS 1.43E-02 1.79E-04 1.48E-02 1.38E-02 5.00E-02 PASS 1.51E-02 1.30E-04 1.55E-02 1.48E-02 5.00E-02 PASS An ISO 9001:2000 Certified Company 84 RLAT Report 08-402 090317 R1.1 Average Biased Average Un-Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (+KTL) Biased Output Voltage Low, No Load CH B @ VS=5V (V) 6.00E-02 5.00E-02 4.00E-02 3.00E-02 2.00E-02 1.00E-02 0.00E+00 0 50 100 150 Total Dose (krad(Si)) Figure 5.40. Plot of the output voltage low (no load) at 5V for channel B versus total dose. The data show no significant change with total dose. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black line(s) show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray line(s) show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed line(s) are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2000 Certified Company 85 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 08-402 090317 R1.1 Table 5.40. Raw data of output voltage low (no load) at 5V for channel B versus total dose, including the statistical analysis, the specification and the status of the testing (pass/fail). Total Dose (krad(Si)) Output Voltage Low, No Load CH B @ VS=5V (V) Device 0 1.39E-02 1.40E-02 1.41E-02 1.36E-02 1.39E-02 1.35E-02 1.36E-02 1.41E-02 1.36E-02 1.35E-02 1.40E-02 1.35E-02 20 1.38E-02 1.40E-02 1.40E-02 1.37E-02 1.40E-02 1.36E-02 1.36E-02 1.41E-02 1.37E-02 1.36E-02 1.41E-02 1.35E-02 50 1.41E-02 1.40E-02 1.42E-02 1.39E-02 1.41E-02 1.37E-02 1.37E-02 1.42E-02 1.39E-02 1.38E-02 1.40E-02 1.35E-02 100 1.41E-02 1.41E-02 1.43E-02 1.39E-02 1.42E-02 1.40E-02 1.41E-02 1.45E-02 1.43E-02 1.43E-02 1.39E-02 1.34E-02 200 1.45E-02 1.46E-02 1.46E-02 1.46E-02 1.45E-02 1.49E-02 1.49E-02 1.51E-02 1.51E-02 1.52E-02 1.40E-02 1.35E-02 1.39E-02 1.87E-04 1.44E-02 1.34E-02 1.39E-02 1.41E-04 1.43E-02 1.35E-02 1.41E-02 1.14E-04 1.44E-02 1.37E-02 1.41E-02 1.48E-04 1.45E-02 1.37E-02 1.46E-02 5.48E-05 1.47E-02 1.44E-02 1.37E-02 2.51E-04 1.43E-02 1.30E-02 2.50E-02 PASS 1.37E-02 2.17E-04 1.43E-02 1.31E-02 3.00E-02 PASS 1.39E-02 2.07E-04 1.44E-02 1.33E-02 4.00E-02 PASS 1.42E-02 1.95E-04 1.48E-02 1.37E-02 5.00E-02 PASS 1.50E-02 1.34E-04 1.54E-02 1.47E-02 5.00E-02 PASS 1090 1092 1093 1094 1095 1096 1097 1098 1099 1100 1106 1113 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MAX Status An ISO 9001:2000 Certified Company 86 RLAT Report 08-402 090317 R1.1 Average Biased Average Un-Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (+KTL) Biased Output Voltage Low, 600Ω CH A @ VS=5V (V) 1.20E-02 1.00E-02 8.00E-03 6.00E-03 4.00E-03 2.00E-03 0.00E+00 0 50 100 150 Total Dose (krad(Si)) Figure 5.41. Plot of the output voltage low (600Ω load) at 5V for channel A versus total dose. The data show no significant change with total dose. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black line(s) show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray line(s) show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed line(s) are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2000 Certified Company 87 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 08-402 090317 R1.1 Table 5.41. Raw data of output voltage low (600Ω load) at 5V for channel A versus total dose, including the statistical analysis, the specification and the status of the testing (pass/fail). Total Dose (krad(Si)) Output Voltage Low, 600Ω CH A @ VS=5V (V) Device 1090 1092 1093 1094 1095 1096 1097 1098 1099 1100 1106 1113 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MAX Status 0 5.80E-03 6.00E-03 6.00E-03 5.60E-03 5.90E-03 5.70E-03 5.80E-03 5.90E-03 5.90E-03 5.80E-03 5.90E-03 5.80E-03 20 5.90E-03 6.10E-03 6.00E-03 5.80E-03 6.00E-03 5.90E-03 5.80E-03 6.00E-03 6.00E-03 5.80E-03 5.90E-03 5.80E-03 50 5.90E-03 5.90E-03 5.90E-03 5.60E-03 5.90E-03 5.70E-03 5.70E-03 5.80E-03 5.80E-03 5.70E-03 5.90E-03 5.80E-03 100 5.40E-03 5.60E-03 5.60E-03 5.30E-03 5.60E-03 5.50E-03 5.50E-03 5.60E-03 5.50E-03 5.50E-03 5.90E-03 5.80E-03 200 4.80E-03 4.90E-03 5.00E-03 4.80E-03 5.10E-03 5.10E-03 5.10E-03 5.10E-03 4.90E-03 4.90E-03 5.90E-03 5.90E-03 5.86E-03 1.67E-04 6.32E-03 5.40E-03 5.96E-03 1.14E-04 6.27E-03 5.65E-03 5.84E-03 1.34E-04 6.21E-03 5.47E-03 5.50E-03 1.41E-04 5.89E-03 5.11E-03 4.92E-03 1.30E-04 5.28E-03 4.56E-03 5.82E-03 8.37E-05 6.05E-03 5.59E-03 1.00E-02 PASS 5.90E-03 1.00E-04 6.17E-03 5.63E-03 1.00E-02 PASS 5.74E-03 5.48E-05 5.89E-03 5.59E-03 1.00E-02 PASS 5.52E-03 4.47E-05 5.64E-03 5.40E-03 1.00E-02 PASS 5.02E-03 1.10E-04 5.32E-03 4.72E-03 1.00E-02 PASS An ISO 9001:2000 Certified Company 88 RLAT Report 08-402 090317 R1.1 Average Biased Average Un-Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (+KTL) Biased Output Voltage Low, 600Ω CH B @ VS=5V (V) 1.20E-02 1.00E-02 8.00E-03 6.00E-03 4.00E-03 2.00E-03 0.00E+00 0 50 100 150 Total Dose (krad(Si)) Figure 5.42. Plot of the output voltage low (600Ω load) at 5V for channel B versus total dose. The data show no significant change with total dose. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black line(s) show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray line(s) show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed line(s) are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2000 Certified Company 89 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 08-402 090317 R1.1 Table 5.42. Raw data of output voltage low (600Ω load) at 5V for channel B versus total dose, including the statistical analysis, the specification and the status of the testing (pass/fail). Total Dose (krad(Si)) Output Voltage Low, 600Ω CH B @ VS=5V (V) Device 1090 1092 1093 1094 1095 1096 1097 1098 1099 1100 1106 1113 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MAX Status 0 6.20E-03 6.20E-03 6.10E-03 5.90E-03 6.30E-03 6.00E-03 5.90E-03 6.10E-03 6.00E-03 5.90E-03 6.20E-03 6.10E-03 20 6.10E-03 6.10E-03 6.20E-03 6.00E-03 6.30E-03 6.10E-03 6.10E-03 6.20E-03 6.10E-03 6.00E-03 6.10E-03 6.10E-03 50 6.00E-03 6.00E-03 6.00E-03 5.70E-03 6.00E-03 6.00E-03 6.00E-03 6.00E-03 6.10E-03 5.90E-03 6.00E-03 6.00E-03 100 5.70E-03 5.70E-03 5.70E-03 5.50E-03 5.80E-03 5.80E-03 5.70E-03 5.80E-03 5.80E-03 5.70E-03 6.10E-03 6.00E-03 200 5.10E-03 5.10E-03 5.30E-03 5.10E-03 5.30E-03 5.30E-03 5.30E-03 5.30E-03 5.10E-03 5.20E-03 6.10E-03 6.00E-03 6.14E-03 1.52E-04 6.56E-03 5.72E-03 6.14E-03 1.14E-04 6.45E-03 5.83E-03 5.94E-03 1.34E-04 6.31E-03 5.57E-03 5.68E-03 1.10E-04 5.98E-03 5.38E-03 5.18E-03 1.10E-04 5.48E-03 4.88E-03 5.98E-03 8.37E-05 6.21E-03 5.75E-03 1.00E-02 PASS 6.10E-03 7.07E-05 6.29E-03 5.91E-03 1.00E-02 PASS 6.00E-03 7.07E-05 6.19E-03 5.81E-03 1.00E-02 PASS 5.76E-03 5.48E-05 5.91E-03 5.61E-03 1.00E-02 PASS 5.24E-03 8.94E-05 5.49E-03 4.99E-03 1.00E-02 PASS An ISO 9001:2000 Certified Company 90 RLAT Report 08-402 090317 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Output Voltage Low, 1mA CH A @ VS=5V (V) 1.80E+00 1.60E+00 1.40E+00 1.20E+00 1.00E+00 8.00E-01 6.00E-01 4.00E-01 2.00E-01 0.00E+00 0 50 100 150 Total Dose (krad(Si)) Figure 5.43. Plot of the output voltage low (1mA load) at 5V for channel A versus total dose. The data show no significant change with total dose. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black line(s) show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray line(s) show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed line(s) are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2000 Certified Company 91 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 08-402 090317 R1.1 Table 5.43. Raw data of the output voltage low (1mA load) at 5V for channel A versus total dose, including the statistical analysis, the specification and the status of the testing (pass/fail). Total Dose (krad(Si)) Output Voltage Low, 1mA CH A @ VS=5V (V) Device 1090 1092 1093 1094 1095 1096 1097 1098 1099 1100 1106 1113 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MAX Status 0 2.49E-01 2.48E-01 2.49E-01 2.53E-01 2.52E-01 2.49E-01 2.51E-01 2.53E-01 2.48E-01 2.48E-01 2.50E-01 2.48E-01 20 2.46E-01 2.46E-01 2.47E-01 2.51E-01 2.49E-01 2.45E-01 2.47E-01 2.48E-01 2.44E-01 2.45E-01 2.49E-01 2.47E-01 50 2.51E-01 2.49E-01 2.49E-01 2.54E-01 2.53E-01 2.48E-01 2.50E-01 2.51E-01 2.48E-01 2.49E-01 2.49E-01 2.47E-01 100 2.59E-01 2.58E-01 2.58E-01 2.65E-01 2.61E-01 2.57E-01 2.60E-01 2.59E-01 2.56E-01 2.59E-01 2.49E-01 2.47E-01 200 3.24E-01 3.06E-01 2.96E-01 4.57E-01 3.00E-01 2.96E-01 2.99E-01 2.88E-01 3.05E-01 4.24E-01 2.49E-01 2.46E-01 2.50E-01 2.17E-03 2.56E-01 2.44E-01 2.48E-01 2.17E-03 2.54E-01 2.42E-01 2.51E-01 2.28E-03 2.57E-01 2.45E-01 2.60E-01 2.95E-03 2.68E-01 2.52E-01 3.37E-01 6.82E-02 5.23E-01 1.50E-01 2.50E-01 2.17E-03 2.56E-01 2.44E-01 3.50E-01 PASS 2.46E-01 1.64E-03 2.50E-01 2.41E-01 8.00E-01 PASS 2.49E-01 1.30E-03 2.53E-01 2.46E-01 1.00E+00 PASS 2.58E-01 1.64E-03 2.63E-01 2.54E-01 1.60E+00 PASS 3.22E-01 5.71E-02 4.79E-01 1.66E-01 1.60E+00 PASS An ISO 9001:2000 Certified Company 92 RLAT Report 08-402 090317 R1.1 Average Biased Average Un-Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (+KTL) Biased Output Voltage Low, 1mA CH B @ VS=5V (V) 1.80E+00 1.60E+00 1.40E+00 1.20E+00 1.00E+00 8.00E-01 6.00E-01 4.00E-01 2.00E-01 0.00E+00 0 50 100 150 Total Dose (krad(Si)) Figure 5.44. Plot of the output voltage low (1mA load) at 5V for channel B versus total dose. The data show no significant change with total dose. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black line(s) show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray line(s) show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed line(s) are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2000 Certified Company 93 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 08-402 090317 R1.1 Table 5.44. Raw data of the output voltage low (1mA load) at 5V for channel B versus total dose, including the statistical analysis, the specification and the status of the testing (pass/fail). Total Dose (krad(Si)) Output Voltage Low, 1mA CH B @ VS=5V (V) Device 1090 1092 1093 1094 1095 1096 1097 1098 1099 1100 1106 1113 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MAX Status 0 2.44E-01 2.43E-01 2.46E-01 2.48E-01 2.46E-01 2.43E-01 2.46E-01 2.48E-01 2.43E-01 2.42E-01 2.46E-01 2.43E-01 20 2.41E-01 2.40E-01 2.42E-01 2.46E-01 2.44E-01 2.39E-01 2.42E-01 2.45E-01 2.40E-01 2.39E-01 2.45E-01 2.41E-01 50 2.45E-01 2.44E-01 2.45E-01 2.49E-01 2.47E-01 2.42E-01 2.45E-01 2.46E-01 2.43E-01 2.44E-01 2.45E-01 2.41E-01 100 2.52E-01 2.52E-01 2.52E-01 2.57E-01 2.54E-01 2.48E-01 2.53E-01 2.53E-01 2.50E-01 2.52E-01 2.45E-01 2.41E-01 200 2.88E-01 2.83E-01 2.80E-01 2.96E-01 2.81E-01 2.76E-01 2.78E-01 2.76E-01 2.81E-01 2.96E-01 2.45E-01 2.40E-01 2.45E-01 1.95E-03 2.51E-01 2.40E-01 2.43E-01 2.41E-03 2.49E-01 2.36E-01 2.46E-01 2.00E-03 2.51E-01 2.41E-01 2.53E-01 2.19E-03 2.59E-01 2.47E-01 2.86E-01 6.58E-03 3.04E-01 2.68E-01 2.44E-01 2.51E-03 2.51E-01 2.38E-01 3.50E-01 PASS 2.41E-01 2.55E-03 2.48E-01 2.34E-01 8.00E-01 PASS 2.44E-01 1.58E-03 2.48E-01 2.40E-01 1.00E+00 PASS 2.51E-01 2.17E-03 2.57E-01 2.45E-01 1.60E+00 PASS 2.81E-01 8.41E-03 3.04E-01 2.58E-01 1.60E+00 PASS An ISO 9001:2000 Certified Company 94 RLAT Report 08-402 090317 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 6.0. Summary / Conclusions The total ionizing dose testing described in this final report was performed using the facilities at Radiation Assured Devices’ Longmire Laboratories in Colorado Springs, CO. The high dose rate total ionizing dose (TID) source is a JLSA 84-21 irradiator modified to provide a panoramic exposure. The Co-60 rods are held in the base of the irradiator heavily shielded by lead, during the radiation exposures the rod is raised by an electronic timer/controller and the exposure is performed in air. The dose rate for this irradiator in this configuration ranges from <1rad(Si)/s to a maximum of approximately 120rad(Si)/s, determined by the distance from the source. The parametric data was obtained as “read and record” and all the raw data plus an attributes summary were presented in this report. The attributes data contains the average, standard deviation and the average with the KTL values applied. The KTL value used was 2.742 per MIL HDBK 814 using onesided tolerance limits of 99/90 and a 5-piece sample size. Note that the following criteria was used to determine the outcome of the testing: following the radiation exposure each parameter had to pass the specification value and the average value for the five-piece sample must pass the specification value when the KTL limits are applied. If these conditions were not both satisfied following the radiation exposure, then the lot would be logged as an RLAT failure. Based on these criteria, the RH1013 dual operational amplifier discussed in this report passed the radiation lot acceptance test to the highest level tested of 200krad(Si). The units showed no significant degradation to most of the measured parameters. As seen in this report, several parameters suffered measurable radiation-induced degradation, however in no case was it sufficient to cause the parameters to go out of specification even after application of the KTL statistics. An ISO 9001:2000 Certified Company 95 RLAT Report 08-402 090317 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Appendix A: TID Bias Connections (Extracted from LINEAR TECHNOLOGY CORPORATION RH1013M Dual Precision Operational Amplifier Datasheet) Biased Samples: Pin 1 2 3 4 5 6 7 8 Function OUT A -IN A +IN A V+IN B -IN B OUT B V+ Bias To Pin 2 Via 10kΩ Resistor To Pin 1 Via 10kΩ Resistor 8V Via 10kΩ Resistor -15V Decoupled to GND w/ 0.1µF 8V Via 10kΩ Resistor To Pin 7 Via 10kΩ Resistor To Pin 6 Via 10kΩ Resistor +15V Decoupled to GND w/ 0.1µF Unbiased Samples (All Pins Tied to Ground): Pin 1 2 3 4 5 6 7 8 Function OUT A -IN A +IN A V+IN B -IN B OUT B V+ Bias GND GND GND GND GND GND GND GND An ISO 9001:2000 Certified Company 96 RLAT Report 08-402 090317 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Figure A.1. Irradiation bias drawing for the units to be irradiated under electrical bias. This figure was extracted from the LINEAR TECHNOLOGY CORPORATION RH1013M Dual Precision Operational Amplifier Datasheet. Figure A.2. Package drawing (for reference only). This figure was extracted from the LINEAR TECHNOLOGY CORPORATION RH1013M Quad Precision Operational Amplifier Datasheet. An ISO 9001:2000 Certified Company 97 RLAT Report 08-402 090317 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Appendix B: Photograph of device-under-test to show part markings An ISO 9001:2000 Certified Company 98 RLAT Report 08-402 090317 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Appendix C: Electrical Test Parameters and Conditions All electrical tests for this device are performed on Radiation Assured Device’s LTS2020 Test System. The LTS2020 Test System is a programmable parametric tester that provides parameter measurements for a variety of digital, analog and mixed signal products including voltage regulators, voltage comparators, D to A and A to D converters. The LTS2020 Test System achieves accuracy and sensitivity through the use of software self-calibration and an internal relay matrix with separate family boards and custom personality adapter boards. The tester uses this relay matrix to connect the required test circuits, select the appropriate voltage / current sources and establish the needed measurement loops for all the tests performed. The measured parameters and test conditions are shown in Table C.1. A listing of the measurement precision/resolution for each parameter is shown in Table C.2. The precision/resolution values were obtained either from test data or from the DAC resolution of the LTS2020. To generate the precision/resolution shown in Table C.2, one of the units-under-test was tested repetitively (a total of 10-times with re-insertion between tests) to obtain the average test value and standard deviation. Using this test data MIL-HDBK-814 90/90 KTL statistics were applied to the measured standard deviation to generate the final measurement range. This value encompasses the precision/resolution of all aspects of the test system, including the LTS2020 mainframe, family board, socket assembly and DUT board as well as insertion error. In some cases, the measurement resolution is limited by the internal DACs, which results in a measured standard deviation of zero. In these instances the precision/resolution will be reported back as the LSB of the DAC. Note that the testing and statistics used in this document are based on an “analysis of variables” technique, which relies on small sample sizes to qualify much larger lot sizes (see MIL-HDBK-814, p. 91 for a discussion of statistical treatments). Unfortunately, not all measured parameters are well suited to this approach due to inherent large variations. One such parameter is pre-irradiation Open Loop Gain, where the device exhibits extreme sensitivity to input conditions, resulting in a very large standard deviation and a statistical error often greater than the measured value. If necessary, larger samples sizes could be used to qualify these parameters using an “attributes” approach. An ISO 9001:2000 Certified Company 99 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 08-402 090317 R1.1 Table C.1. Measured parameters and test conditions for the RH1013MJ8. Unless otherwise noted the conditions were selected to match the post-irradiation specifications. See LINEAR TECHNOLOGY CORPORATION RH1013M Dual Precision Operational Amplifier Datasheet for the post irradiation test conditions and specifications. Test Number Test Description Test Conditions 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Positive Supply Current (ICC+) Negative Supply Current (IEE-) Input Offset Voltage (VOS1-VOS2) Input Offset Current (IOS1-IOS2) + Input Bias Current (IB+1-IB+2) - Input Bias Current (IB-1-IB-2) Common Mode Rejection Ratio (CMRR1-CMRR2) Power Supply Rejection Ratio (PSRR1-PSRR2) Large Signal Voltage Gain (AVOL1-AVOL2) Positive Output Voltage Swing (VOUT+1-VOUT+2) Negative Output Voltage Swing (VOUT-1-VOUT-2) Positive Slew Rate (SlewRate+1-SlewRate+2) Negative Slew Rate (SlewRate-1-SlewRate-2) Positive Supply Current (ICC+2) Negative Supply Current (IEE-2) Input Offset Voltage (VOS3-VOS4) Input Offset Current (IOS3-IOS4) + Input Bias Current (IB+3-IB+4) - Input Bias Current (IB-3-IB-4) Positive Output Voltage Swing (VOUT+3-VOUT+4) Positive Output Voltage Swing (VOUT+5-VOUT+6) Negative Output Voltage Swing (VOUT-3-VOUT-4) Negative Output Voltage Swing (VOUT-5-VOUT-6) Negative Output Voltage Swing (VOUT-7-VOUT-8) VS=±15V VS=±15V VS=±15V VS=±15V VS=±15V VS=±15V VCM = 13V, –15V VS = ±10V to ±18V VS=±15V, VO = ±10V, RL = 10kΩ VS=±15V, RL= 10kΩ VS=±15V, RL= 10kΩ VS=±15V, RL= 10kΩ VS=±15V, RL= 10kΩ VS=+5V VS=+5V VS=+5V VS=+5V VS=+5V VS=+5V VS=+5V, No Load VS=+5V, RL = 600Ω VS=+5V, No Load VS=+5V, RL = 600Ω VS=+5V, ISINK = 1mA An ISO 9001:2000 Certified Company 100 RLAT Report 08-402 090317 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Table C.2. Measured parameters, pre-irradiation specifications and measurement resolution for the RH1013MJ8. Measured Parameter Pre-Irradiation Specification Measurement Precision/Resolution Positive Supply Current (ICC+) Negative Supply Current (IEE-) Input Offset Voltage (VOS1-VOS2) Input Offset Current (IOS1-IOS2) + Input Bias Current (IB+1-IB+2) - Input Bias Current (IB-1-IB-2) Common Mode Rejection Ratio (CMRR1-CMRR2) Power Supply Rejection Ratio (PSRR1-PSRR2) Large Signal Voltage Gain (AVOL1-AVOL2) Positive Output Voltage Swing (VOUT+1-VOUT+2) Negative Output Voltage Swing (VOUT-1-VOUT-2) Positive Slew Rate (SlewRate+1-SlewRate+2) Negative Slew Rate (SlewRate-1-SlewRate-2) Positive Supply Current (ICC+2) Negative Supply Current (IEE-2) Input Offset Voltage (VOS3-VOS4) Input Offset Current (IOS3-IOS4) + Input Bias Current (IB+3-IB+4) - Input Bias Current (IB-3-IB-4) Output Voltage High (VOUT+3-VOUT+4) Output Voltage High (VOUT+5-VOUT+6) Output Voltage Low (VOUT-3-VOUT-4) Output Voltage Low (VOUT-5-VOUT-6) Output Voltage Low (VOUT-7-VOUT-8) 1.1mA MAX -1.1mA MIN ±300µV MAX ±10nA MAX ±30nA MAX ±30nA MAX 97dB MIN 100dB MIN 1200V/mV MIN 12.5V MIN -12.5V MAX 0.2V/ µs MIN -0.2V/ µs MAX 1.0mA MAX -1.0mA MIN ±450µV MAX ±10nA MAX ±50nA MAX ±50nA MAX 4V MIN 3.4V MIN 25mV MAX 10mV MAX 350mV MAX ±2.83E-6A ±2.05E-6A ±2.61E-6V ±2.65E-10A ±5.05E-11A ±3.49E-10A ±0.88dB ±10.9dB ±9.36E3V/mV ±1.31E-3V ±1.44E-3V ±1.30E-2V/ µs ±1.97E-2V/ µs ±2.62E-6A ±3.70E-6A ±1.63E-6V ±1.11E-10A ±4.23E-11A ±9.83E-11 ±1.17E-3V ±9.97E-4V ±1.38E-4V ±1.44E-4V ±9.97E-4V An ISO 9001:2000 Certified Company 101 RLAT Report 08-402 090317 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Appendix D: Additional Data Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN 1.60E+02 Large Signal Voltage Gain CH A (dB) 1.40E+02 1.20E+02 1.00E+02 8.00E+01 6.00E+01 4.00E+01 2.00E+01 0.00E+00 0 50 100 150 200 Total Dose (krad(Si)) Figure D.1. Plot of open loop gain for channel A in dB versus total dose. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black lines show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray lines show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed lines are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2000 Certified Company 102 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 08-402 090317 R1.1 Table D.1. Raw data of the open loop gain for channel A in dB versus total dose, including the statistical analysis, the specification and the status of the testing (pass/fail). Large Signal Voltage Gain CH A (dB) Device 1090 1092 1093 1094 1095 1096 1097 1098 1099 1100 1106 1113 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status 0 1.45E+02 1.46E+02 1.44E+02 1.44E+02 1.43E+02 1.44E+02 1.44E+02 1.45E+02 1.44E+02 1.46E+02 1.47E+02 1.44E+02 Total Dose (krad(Si)) 20 50 100 1.44E+02 1.46E+02 1.42E+02 1.44E+02 1.46E+02 1.43E+02 1.46E+02 1.43E+02 1.45E+02 1.41E+02 1.45E+02 1.43E+02 1.46E+02 1.44E+02 1.42E+02 1.43E+02 1.45E+02 1.47E+02 1.43E+02 1.44E+02 1.46E+02 1.43E+02 1.46E+02 1.42E+02 1.46E+02 1.47E+02 1.44E+02 1.46E+02 1.42E+02 1.44E+02 1.44E+02 1.45E+02 1.44E+02 1.46E+02 1.45E+02 1.44E+02 200 1.45E+02 1.43E+02 1.45E+02 1.48E+02 1.45E+02 1.47E+02 1.44E+02 1.44E+02 1.45E+02 1.45E+02 1.44E+02 1.42E+02 1.44E+02 1.12E+00 1.47E+02 1.41E+02 1.44E+02 2.13E+00 1.50E+02 1.38E+02 1.45E+02 1.33E+00 1.48E+02 1.41E+02 1.45E+02 1.87E+00 1.50E+02 1.40E+02 1.45E+02 8.48E-01 1.47E+02 1.42E+02 1.22E+02 PASS 1.44E+02 1.59E+00 1.49E+02 1.40E+02 1.06E+02 PASS 1.45E+02 1.81E+00 1.50E+02 1.40E+02 1.00E+02 PASS An ISO 9001:2000 Certified Company 103 1.43E+02 1.14E+00 1.46E+02 1.40E+02 1.45E+02 1.45E+02 1.70E+00 1.39E+00 1.49E+02 1.49E+02 1.40E+02 1.41E+02 9.40E+01 8.80E+01 PASS PASS RLAT Report 08-402 090317 R1.1 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (-KTL) Biased Large Signal Voltage Gain CH B (dB) 1.60E+02 1.40E+02 1.20E+02 1.00E+02 8.00E+01 6.00E+01 4.00E+01 2.00E+01 0.00E+00 0 50 100 150 200 Total Dose (krad(Si)) Figure D.2. Plot of open loop gain for channel B in dB versus total dose. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black lines show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray lines show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed lines are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2000 Certified Company 104 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 08-402 090317 R1.1 Table D.2. Raw data of the open loop gain for channel B in dB versus total dose, including the statistical analysis, the specification and the status of the testing (pass/fail). Large Signal Voltage Gain CH B (dB) Device 1090 1092 1093 1094 1095 1096 1097 1098 1099 1100 1106 1113 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status 0 1.48E+02 1.48E+02 1.48E+02 1.47E+02 1.47E+02 1.48E+02 1.50E+02 1.49E+02 1.47E+02 1.48E+02 1.48E+02 1.46E+02 Total Dose (krad(Si)) 20 50 100 1.48E+02 1.49E+02 1.49E+02 1.51E+02 1.47E+02 1.49E+02 1.48E+02 1.51E+02 1.50E+02 1.50E+02 1.48E+02 1.52E+02 1.50E+02 1.49E+02 1.49E+02 1.49E+02 1.48E+02 1.48E+02 1.48E+02 1.49E+02 1.49E+02 1.48E+02 1.50E+02 1.49E+02 1.50E+02 1.48E+02 1.49E+02 1.48E+02 1.50E+02 1.49E+02 1.49E+02 1.50E+02 1.48E+02 1.47E+02 1.48E+02 1.48E+02 200 1.49E+02 1.50E+02 1.50E+02 1.50E+02 1.47E+02 1.49E+02 1.49E+02 1.46E+02 1.47E+02 1.46E+02 1.50E+02 1.50E+02 1.48E+02 5.43E-01 1.49E+02 1.46E+02 1.49E+02 1.13E+00 1.53E+02 1.46E+02 1.49E+02 1.62E+00 1.53E+02 1.44E+02 1.50E+02 1.08E+00 1.53E+02 1.47E+02 1.49E+02 1.16E+00 1.52E+02 1.46E+02 1.48E+02 1.14E+00 1.51E+02 1.45E+02 1.22E+02 PASS 1.49E+02 1.03E+00 1.51E+02 1.46E+02 1.06E+02 PASS 1.49E+02 1.04E+00 1.52E+02 1.46E+02 1.00E+02 PASS 1.49E+02 3.59E-01 1.50E+02 1.48E+02 9.40E+01 PASS 1.47E+02 1.52E+00 1.51E+02 1.43E+02 8.80E+01 PASS An ISO 9001:2000 Certified Company 105