RLAT Report 10-055 100219 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Radiation Lot Acceptance Testing (RLAT) of the RH1013MW Dual Precision Operational Amplifier for Linear Technology Customer: Linear Technology, PO# 55227L RAD Job Number: 10-055 Part Type Tested: Linear Technology RH1013MW Dual Precision Operational Amplifier Commercial Part Number: RH1013MW Traceability Information: Fab Lot# W10722836.1, Wafer 13, Assembly Lot #547884.1. Information obtained from Linear Technology PO#55227L. Date code marking on the package is 0944A, see Appendix A for a photograph of the device and part markings. Quantity of Units: 12 units total, 5 units for biased irradiation, 5 units for unbiased irradiation (all pins tied to ground) and 2 control units. Serial numbers 41, 116, 182, 241, and 325 were biased during irradiation. Serial numbers 408, 492, 724, 786, and 868 were unbiased during irradiation (all pins tied to ground). Serial numbers 929 and 1012 were used as controls. See Appendix B for the radiation bias connection table. Pre-Irradiation Burn-In: Burn-In performed by Linear Technology prior to receipt by RAD. TID Dose Rate and Test Increments: 200krad(Si). 50-300rad(Si)/s with readings at pre-irradiation, 20, 50, 100, and TID Overtest and Post-Irradiation Anneal: No overtest or anneal. TID Test Standard: MIL-STD-883G, Method 1019.7, Condition A TID Electrical Test Conditions: Pre-irradiation, and within one hour following each radiation exposure. Test Programs: RH1013LT.SRC Test Hardware: LTS2020 Tester, 2101 Family Board, 0600 Fixture, and RH1013 LTS0325 DUT Board Facility and Radiation Source: Radiation Assured Devices Longmire Laboratories, Colorado Springs, CO using the JLSA 81-24 high dose rate Co60 source. Dosimetry performed by CaF2 TLDs traceable to NIST. RAD’s dosimetry has been audited by DSCC and RAD has been awarded Laboratory Suitability for MIL-STD-750 TM 1019.5. Irradiation and Test Temperature: Ambient room temperature for irradiation and test controlled to 24°C±6°C per MIL-STD-883. RLAT Result: PASSED. Units pass to 100krad(Si) and 200krad(Si) with all parameters remaining within their post-irradiation specifications including after application of the KTL statistics. An ISO 9001:2008 and DSCC Certified Company 1 RLAT Report 10-055 100219 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 1.0. Overview and Background It is well known that total dose ionizing radiation can cause parametric degradation and ultimately functional failure in electronic devices. The damage occurs via electron-hole pair production, transport and trapping in the dielectric and interface regions. In discrete devices the bulk of the damage is frequently manifested as a reduction in the gain and/or breakdown voltage of the device. The damage will usually anneal with time following the end of the radiation exposure. Due to this annealing, and to ensure a worst-case test condition MIL-STD-883 TM1019.7 calls out a dose rate of 50 to 300rad(Si)/s as Condition A and further specifies that the time from the end of an incremental radiation exposure and electrical testing shall be 1-hour or less and the total time from the end of one incremental irradiation to the beginning of the next incremental radiation step should be 2-hours or less. The work described in this report was performed to meet MIL-STD-883 TM1019.7 Condition A. 2.0. Radiation Test Apparatus The total ionizing dose testing described in this final report was performed using the facilities at Radiation Assured Devices’ Longmire Laboratories in Colorado Springs, CO. The high dose rate total ionizing dose (TID) source is a JLSA 84-21 irradiator modified to provide a panoramic exposure. The Co-60 rods are held in the base of the irradiator heavily shielded by lead, during the radiation exposures the rod is raised by an electronic timer/controller and the exposure is performed in air. The dose rate for this irradiator in this configuration ranges from <1rad(Si)/s to a maximum of approximately 120rad(Si)/s, determined by the distance from the source. For high-dose rate experiments the bias boards are placed in a radial fashion equidistant from the raised Co-60 rods with the distance adjusted to provide the required dose rate. The irradiator calibration is maintained by Radiation Assured Devices Longmire Laboratories using thermoluminescent dosimeters (TLDs)) traceable to the National Institute of Standards and Technology (NIST). Figure 2.1 shows a photograph of the JLSA 81-24 Co-60 irradiator at RAD’s Longmire Laboratory facility. RAD is currently certified by the Defense Supply Center Columbus (DSCC) for Laboratory Suitability under MIL STD 750. Additional details regarding Radiation Assured Devices dosimetry for TM1019 Condition A testing are available in RAD’s report to DSCC entitled: “Dose Rate Mapping of the J.L. Shepherd and Associates Model 81 Irradiator Installed by Radiation Assured Devices” An ISO 9001:2008 and DSCC Certified Company 2 RLAT Report 10-055 100219 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Figure 2.1. Radiation Assured Devices’ high dose rate Co-60 irradiator. The dose rate is obtained by positioning the device-under-test at a fixed distance from the gamma cell. The dose rate for this irradiator varies from approximately 120rad(Si)/s close to the rods down to 1rad(Si)/s at a distance of approximately 2-feet. An ISO 9001:2008 and DSCC Certified Company 3 RLAT Report 10-055 100219 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 3.0. Radiation Test Conditions The RH1013M dual operational amplifier described in this final report was irradiated using a split 15V supply and with all pins tied to ground, that is biased and unbiased. See the TID Bias Table in Appendix B for the full bias circuits. These bias circuits satisfy the requirements of MIL-STD-883G TM1019.7 Section 3.9.3 Bias and Loading Conditions which states “The bias applied to the test devices shall be selected to produce the greatest radiation induced damage or the worst-case damage for the intended application, if known. While maximum voltage is often worst case some bipolar linear device parameters (e.g. input bias current or maximum output load current) exhibit more degradation with 0 V bias.” The devices were irradiated to a maximum total ionizing dose level of 200krad(Si) with incremental readings at 20, 50, 100 and 200krad(Si) for all electrical tests using the ±15V supply and with incremental readings at 20, 50 and 100krad(Si) for all electrical tests using the +5V and 0V supply conditions (See LINEAR TECHNOLOGY CORPORATION RH1013M Dual Precision Operational Amplifier Datasheet Page 3, Note 2). Electrical testing occurred within one hour following the end of each irradiation segment. For intermediate irradiations, the parts were tested and returned to total dose exposure within two hours from the end of the previous radiation increment. Note that the RH1013 is specified to 100krad(Si) in the +VS=5V, -VS=0 supply conditions. The 200krad(Si) data shown in this report for those parameters should be used for reference only. The TID bias board was positioned in the Co-60 cell to provide the required minimum of 50rad(Si)/s and was located inside a lead-aluminum enclosure. The lead-aluminum enclosure is required under MIL-STD-883G TM1019.7 Section 3.4 that reads as follows: “Lead/Aluminum (Pb/Al) container. Test specimens shall be enclosed in a Pb/Al container to minimize dose enhancement effects caused by lowenergy, scattered radiation. A minimum of 1.5 mm Pb, surrounding an inner shield of at least 0.7 mm Al, is required. This Pb/Al container produces an approximate charged particle equilibrium for Si and for TLDs such as CaF2. The radiation field intensity shall be measured inside the Pb/Al container (1) initially, (2) when the source is changed, or (3) when the orientation or configuration of the source, container, or test-fixture is changed. This measurement shall be performed by placing a dosimeter (e.g., a TLD) in the device-irradiation container at the approximate test-device position. If it can be demonstrated that low energy scattered radiation is small enough that it will not cause dosimetry errors due to dose enhancement, the Pb/Al container may be omitted”. The final dose rate within the high dose rate lead-aluminum enclosure was determined based on TLD dosimetry measurements (see previous section). The final dose rate for this work was 56.0rad(Si)/s with a precision of ±5%. An ISO 9001:2008 and DSCC Certified Company 4 RLAT Report 10-055 100219 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 4.0. Tested Parameters During the radiation lot acceptance testing the following pre- and post-irradiation electrical parameters were measured: ±15V Tests 1. Positive Supply Current (ICC+) 2. Negative Supply Current (IEE-) 3. Input Offset Voltage (VOS Channel A and B) 4. Input Offset Current (IOS Channel A and B) 5. + Input Bias Current (IB+ Channel A and B) 6. - Input Bias Current (IB- Channel A and B) 7. Common Mode Rejection Ratio (CMRR Channel A and B) 8. Power Supply Rejection Ratio (PSRR Channel A and B) 9. Large Signal Voltage Gain (AVOL Channel A and B) 10. Positive Output Voltage Swing, No Load (VOUT Channel A and B) 11. Positive Output Voltage Swing, 600Ω (VOUT Channel A and B) 12. Negative Output Voltage Swing, No Load (VOUT Channel A and B) 13. Negative Output Voltage Swing, 600Ω (VOUT Channel A and B) 14. Positive Slew Rate (SlewRate+ Channel A and B) 15. Negative Slew Rate (SlewRate- Channel A and B) +5V Tests 16. Positive Supply Current (ICC+2) 17. Negative Supply Current (IEE-2) 18. Input Offset Voltage (VOS Channel A and B) 19. Input Offset Current (IOS Channel A and B) 20. + Input Bias Current (IB+ Channel A and B) 21. - Input Bias Current (IB- Channel A and B) 22. Output Voltage High, No Load (VOUT Channel A and B) 23. Output Voltage High, 600Ω (VOUT Channel A and B) 24. Output Voltage Low, No Load (VOUT Channel A and B) 25. Output Voltage Low, 600Ω (VOUT Channel A and B) 26. Output Voltage Low, 1mA (VOUT Channel A and B) The parametric data was obtained as read and record and all the raw data plus an attributes summary are contained in a separate Excel file. The attributes data contains the average, standard deviation and the average with the KTL values applied. The KTL value used is 2.742 per MIL HDBK 814 using one sided tolerance limits of 90/90 and a 5-piece sample size. Note that the following criteria must be met for a device to pass the RLAT: following the radiation exposure each of the 5 pieces shall pass the An ISO 9001:2008 and DSCC Certified Company 5 RLAT Report 10-055 100219 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 specification value and the average value for the ten-piece sample must pass the specification value when the KTL limits are applied. If either of these conditions is not satisfied following the radiation exposure, then the lot could be logged as a failure. 5.0. Total Ionizing Dose Test Results The RH1013M operational amplifiers from the lot of material described on the first page of this report passed the RLAT to the maximum tested level of 100krad(Si) and 200krad(Si) without significant degradation to most of the measured parameters. As seen in the data plots, several parameters suffered measurable radiation-induced degradation, however in no case was the degradation sufficient to cause the parameters to go out of specification even after application of the KTL statistics. Note that PSSR for Channel A was out of specification pre-irradiation and at the first two dose levels. In our opinion this is due to the distribution within the sample population and is not reflective of radiation-induced degradation of the parameter. Further note that RH1013 is specified to 100krad(Si) in the +VS=5V, VS=0 supply conditions and the 200krad(Si) data shown in this report for those parameters should be used for reference only. Figures 5.1 and 5.44 show plots of all the measured parameters versus total ionizing dose while Tables 5.1 – 5.44 show the corresponding raw data for each of these parameters. Appendix D lists the figure numbers and titles for convenience. In the data plots the solid diamonds are the average of the measured data points for the sample irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the units irradiated with all pins tied to ground. The black lines (solid or dashed) are the average of the data points after application of the KTL statistics on the sample irradiated in the biased condition while the shaded lines (solid or dashed) are the average of the data points after application of the KTL statistics on the sample irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or postirradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. The control units, as expected, show no significant changes to any of the parameters. Therefore we can conclude that the electrical testing remained in control throughout the duration of the tests and that any observed degradation was due to the radiation exposure. An ISO 9001:2008 and DSCC Certified Company 6 RLAT Report 10-055 100219 R1.1 Average Biased Average Un-Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (+KTL) Biased 1.20E-03 Positive Supply Current (A) 1.10E-03 1.00E-03 9.00E-04 8.00E-04 7.00E-04 6.00E-04 5.00E-04 4.00E-04 0 50 100 150 Total Dose (krad(Si)) Figure 5.1. Plot of positive supply current (±15V) versus total dose. The data shows a general improvement with radiation. The solid diamonds are the average of the measured data points for the sample irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the units irradiated with all pins tied to ground. The black lines (solid or dashed) are the average of the data points after application of the KTL statistics on the sample irradiated in the biased condition while the shaded lines (solid or dashed) are the average of the data points after application of the KTL statistics on the sample irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 7 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 10-055 100219 R1.1 Table 5.1. Raw data for Positive Supply Current (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Supply Current (A) Device 41 116 182 241 325 408 492 724 786 868 929 1012 Total Dose (krad(Si)) 0 7.80E-04 7.88E-04 8.25E-04 8.46E-04 7.78E-04 7.65E-04 7.87E-04 7.90E-04 7.85E-04 8.61E-04 8.11E-04 8.14E-04 20 7.79E-04 7.89E-04 8.24E-04 8.47E-04 7.79E-04 7.73E-04 7.93E-04 7.96E-04 7.89E-04 8.77E-04 8.13E-04 8.18E-04 50 7.65E-04 7.86E-04 8.10E-04 8.31E-04 7.71E-04 7.53E-04 7.76E-04 7.74E-04 7.69E-04 8.62E-04 8.12E-04 8.18E-04 100 7.20E-04 7.48E-04 7.66E-04 7.92E-04 7.30E-04 7.06E-04 7.28E-04 7.26E-04 7.19E-04 8.18E-04 8.14E-04 8.18E-04 200 6.38E-04 6.70E-04 6.84E-04 7.09E-04 6.48E-04 6.05E-04 6.22E-04 6.29E-04 6.15E-04 7.21E-04 8.14E-04 8.19E-04 Biased Statistics Average Biased 8.03E-04 8.04E-04 7.93E-04 7.51E-04 6.70E-04 Std Dev Biased 3.05E-05 3.05E-05 2.76E-05 2.88E-05 2.84E-05 Ps90%/90% (+KTL) Biased 8.87E-04 8.87E-04 8.68E-04 8.30E-04 7.48E-04 Ps90%/90% (-KTL) Biased 7.20E-04 7.20E-04 7.17E-04 6.72E-04 5.92E-04 Un-Biased Statistics Average Un-Biased 7.98E-04 8.06E-04 7.87E-04 7.39E-04 6.38E-04 Std Dev Un-Biased 3.68E-05 4.09E-05 4.30E-05 4.48E-05 4.70E-05 Ps90%/90% (+KTL) Un-Biased 8.98E-04 9.18E-04 9.05E-04 8.62E-04 7.67E-04 Ps90%/90% (-KTL) Un-Biased 6.97E-04 6.93E-04 6.69E-04 6.17E-04 5.09E-04 Specification MAX 1.10E-03 1.10E-03 1.10E-03 1.10E-03 1.10E-03 Status PASS PASS PASS PASS PASS An ISO 9001:2008 and DSCC Certified Company 8 RLAT Report 10-055 100219 R1.1 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (-KTL) Biased -4.00E-04 Negative Supply Current (A) -5.00E-04 -6.00E-04 -7.00E-04 -8.00E-04 -9.00E-04 -1.00E-03 -1.10E-03 -1.20E-03 0 50 100 150 Total Dose (krad(Si)) Figure 5.2. Plot of Negative Supply Current @ +/-15V (A) versus total dose. The data show a general improvement with radiation. The solid diamonds are the average of the measured data points for the sample irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the units irradiated with all pins tied to ground. The black lines (solid or dashed) are the average of the data points after application of the KTL statistics on the sample irradiated in the biased condition while the shaded lines (solid or dashed) are the average of the data points after application of the KTL statistics on the sample irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 9 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 10-055 100219 R1.1 Table 5.2. Raw data for Negative Supply Current (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Supply Current (A) Device 41 116 182 241 325 408 492 724 786 868 929 1012 Total Dose (krad(Si)) 0 -7.80E-04 -7.89E-04 -8.25E-04 -8.46E-04 -7.78E-04 -7.66E-04 -7.87E-04 -7.88E-04 -7.86E-04 -8.62E-04 -8.11E-04 -8.17E-04 20 -7.79E-04 -7.89E-04 -8.24E-04 -8.48E-04 -7.80E-04 -7.72E-04 -7.93E-04 -7.98E-04 -7.92E-04 -8.77E-04 -8.15E-04 -8.18E-04 50 -7.64E-04 -7.84E-04 -8.11E-04 -8.33E-04 -7.71E-04 -7.54E-04 -7.77E-04 -7.74E-04 -7.68E-04 -8.64E-04 -8.12E-04 -8.18E-04 100 -7.20E-04 -7.47E-04 -7.68E-04 -7.91E-04 -7.30E-04 -7.07E-04 -7.29E-04 -7.26E-04 -7.18E-04 -8.18E-04 -8.14E-04 -8.18E-04 200 -6.38E-04 -6.69E-04 -6.86E-04 -7.10E-04 -6.50E-04 -6.05E-04 -6.26E-04 -6.31E-04 -6.17E-04 -7.23E-04 -8.15E-04 -8.17E-04 Biased Statistics Average Biased -8.04E-04 -8.04E-04 -7.93E-04 -7.51E-04 -6.71E-04 Std Dev Biased 3.03E-05 3.07E-05 2.88E-05 2.88E-05 2.86E-05 Ps90%/90% (+KTL) Biased -7.20E-04 -7.20E-04 -7.13E-04 -6.72E-04 -5.92E-04 Ps90%/90% (-KTL) Biased -8.87E-04 -8.88E-04 -8.72E-04 -8.30E-04 -7.49E-04 Un-Biased Statistics Average Un-Biased -7.98E-04 -8.06E-04 -7.87E-04 -7.40E-04 -6.40E-04 Std Dev Un-Biased 3.70E-05 4.07E-05 4.37E-05 4.46E-05 4.72E-05 Ps90%/90% (+KTL) Un-Biased -6.96E-04 -6.95E-04 -6.68E-04 -6.17E-04 -5.11E-04 Ps90%/90% (-KTL) Un-Biased -8.99E-04 -9.18E-04 -9.07E-04 -8.62E-04 -7.70E-04 Specification MIN -1.10E-03 -1.10E-03 -1.10E-03 -1.10E-03 -1.10E-03 Status PASS PASS PASS PASS PASS An ISO 9001:2008 and DSCC Certified Company 10 RLAT Report 10-055 100219 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 1.00E-03 Input Offset Voltage CH A (V) 8.00E-04 6.00E-04 4.00E-04 2.00E-04 0.00E+00 -2.00E-04 -4.00E-04 -6.00E-04 -8.00E-04 -1.00E-03 0 50 100 150 Total Dose (krad(Si)) Figure 5.3. Plot of input offset voltage for channel A @ +/-15V (A) versus total dose. The data show some increase with radiation, however it is not sufficient for the parameter to exceed the post-irradiation specification limits. The solid diamonds are the average of the measured data points for the sample irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the units irradiated with all pins tied to ground. The black lines (solid or dashed) are the average of the data points after application of the KTL statistics on the sample irradiated in the biased condition while the shaded lines (solid or dashed) are the average of the data points after application of the KTL statistics on the sample irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan An ISO 9001:2008 and DSCC Certified Company 11 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 10-055 100219 R1.1 Table 5.3. Raw data for Input Offset Voltage CH A (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Input Offset Voltage CH A (V) Device 41 116 182 241 325 408 492 724 786 868 929 1012 Total Dose (krad(Si)) 0 5.30E-05 -2.36E-05 -3.24E-05 9.60E-07 1.51E-05 -6.69E-05 2.25E-05 -2.51E-05 -1.16E-04 -1.12E-05 -8.46E-06 5.32E-05 20 3.44E-05 -2.14E-05 -2.79E-05 7.48E-06 1.77E-05 -5.12E-05 1.88E-05 -1.70E-05 -1.07E-04 -1.76E-05 -6.89E-06 5.38E-05 50 5.48E-05 -1.91E-05 -7.85E-06 2.37E-05 3.42E-05 -2.23E-05 3.62E-05 2.05E-06 -7.72E-05 -2.78E-05 -6.52E-06 5.36E-05 100 8.40E-05 -1.15E-05 2.28E-05 4.78E-05 5.23E-05 2.93E-05 7.26E-05 5.36E-05 -1.46E-05 -4.76E-05 -6.64E-06 5.34E-05 200 1.48E-04 -4.60E-06 7.55E-05 1.08E-04 9.56E-05 1.29E-04 1.59E-04 1.49E-04 1.04E-04 -7.82E-05 -6.16E-06 5.41E-05 Biased Statistics Average Biased 2.63E-06 2.07E-06 1.71E-05 3.91E-05 8.45E-05 Std Dev Biased 3.39E-05 2.63E-05 3.04E-05 3.57E-05 5.65E-05 Ps90%/90% (+KTL) Biased 9.57E-05 7.42E-05 1.00E-04 1.37E-04 2.39E-04 Ps90%/90% (-KTL) Biased -9.04E-05 -7.01E-05 -6.61E-05 -5.87E-05 -7.04E-05 Un-Biased Statistics Average Un-Biased -3.93E-05 -3.48E-05 -1.78E-05 1.87E-05 9.25E-05 Std Dev Un-Biased 5.34E-05 4.73E-05 4.17E-05 4.93E-05 9.78E-05 Ps90%/90% (+KTL) Un-Biased 1.07E-04 9.49E-05 9.65E-05 1.54E-04 3.61E-04 Ps90%/90% (-KTL) Un-Biased -1.86E-04 -1.64E-04 -1.32E-04 -1.17E-04 -1.76E-04 Specification MIN -3.00E-04 -4.50E-04 -6.00E-04 -7.50E-04 -9.00E-04 Status PASS PASS PASS PASS PASS Specification MAX 3.00E-04 4.50E-04 6.00E-04 7.50E-04 9.00E-04 Status PASS PASS PASS PASS PASS An ISO 9001:2008 and DSCC Certified Company 12 RLAT Report 10-055 100219 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 1.00E-03 Input Offset Voltage CH B (V) 8.00E-04 6.00E-04 4.00E-04 2.00E-04 0.00E+00 -2.00E-04 -4.00E-04 -6.00E-04 -8.00E-04 -1.00E-03 0 50 100 150 Total Dose (krad(Si)) Figure 5.4. Plot of input offset voltage for channel B @ +/-15V (A) versus total dose. The data show some increase with radiation, however it is not sufficient for the parameter to exceed the post-irradiation specification limits. The solid diamonds are the average of the measured data points for the sample irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the units irradiated with all pins tied to ground. The black lines (solid or dashed) are the average of the data points after application of the KTL statistics on the sample irradiated in the biased condition while the shaded lines (solid or dashed) are the average of the data points after application of the KTL statistics on the sample irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 13 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 10-055 100219 R1.1 Table 5.4. Raw data for Input Offset Voltage CH B (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Input Offset Voltage CH B (V) Device 41 116 182 241 325 408 492 724 786 868 929 1012 Total Dose (krad(Si)) 0 -2.49E-05 4.25E-05 -3.33E-05 4.84E-05 3.84E-05 -4.91E-05 5.42E-05 -5.93E-05 -7.28E-05 3.02E-05 1.53E-05 -3.14E-05 20 -1.85E-05 5.82E-05 -2.32E-05 6.92E-05 5.24E-05 -4.84E-05 5.65E-05 -4.20E-05 -5.89E-05 4.06E-05 1.58E-05 -3.19E-05 50 3.50E-06 7.55E-05 -3.02E-06 9.45E-05 6.99E-05 -1.47E-05 7.16E-05 -1.10E-05 -2.67E-05 5.35E-05 1.63E-05 -3.19E-05 100 3.65E-05 9.70E-05 2.23E-05 1.32E-04 9.92E-05 3.83E-05 1.11E-04 4.60E-05 2.25E-05 8.72E-05 1.67E-05 -3.07E-05 200 9.51E-05 1.46E-04 8.42E-05 2.06E-04 1.55E-04 1.59E-04 1.95E-04 1.55E-04 1.53E-04 1.55E-04 1.67E-05 -3.09E-05 Biased Statistics Average Biased 1.42E-05 2.76E-05 4.81E-05 7.73E-05 1.37E-04 Std Dev Biased 3.98E-05 4.47E-05 4.47E-05 4.61E-05 4.93E-05 Ps90%/90% (+KTL) Biased 1.23E-04 1.50E-04 1.71E-04 2.04E-04 2.73E-04 Ps90%/90% (-KTL) Biased -9.50E-05 -9.49E-05 -7.44E-05 -4.91E-05 1.96E-06 Un-Biased Statistics Average Un-Biased -1.94E-05 -1.05E-05 1.45E-05 6.10E-05 1.63E-04 Std Dev Un-Biased 5.75E-05 5.45E-05 4.47E-05 3.69E-05 1.77E-05 Ps90%/90% (+KTL) Un-Biased 1.38E-04 1.39E-04 1.37E-04 1.62E-04 2.12E-04 Ps90%/90% (-KTL) Un-Biased -1.77E-04 -1.60E-04 -1.08E-04 -4.00E-05 1.15E-04 Specification MIN -3.00E-04 -4.50E-04 -6.00E-04 -7.50E-04 -9.00E-04 Status PASS PASS PASS PASS PASS Specification MAX 3.00E-04 4.50E-04 6.00E-04 7.50E-04 9.00E-04 Status PASS PASS PASS PASS PASS An ISO 9001:2008 and DSCC Certified Company 14 RLAT Report 10-055 100219 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Input Offset Current CH A (A) 3.00E-08 2.00E-08 1.00E-08 0.00E+00 -1.00E-08 -2.00E-08 -3.00E-08 0 50 100 150 Total Dose (krad(Si)) Figure 5.5. Plot of Input Offset Current CH A (A) versus total dose. The data show no significant change with total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 15 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 10-055 100219 R1.1 Table 5.5. Raw data for Input Offset Current CH A (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Input Offset Current CH A (A) Device 41 116 182 241 325 408 492 724 786 868 929 1012 Total Dose (krad(Si)) 0 -1.70E-10 6.80E-11 4.90E-11 -2.40E-11 4.50E-11 -8.40E-11 0.00E+00 8.60E-11 -4.00E-12 2.81E-10 -7.20E-11 -1.20E-11 20 -1.95E-10 5.40E-11 3.60E-11 -6.70E-11 2.30E-11 -1.87E-10 -1.20E-11 9.80E-11 -3.30E-11 3.90E-10 -7.80E-11 -1.80E-11 50 -8.80E-11 1.11E-10 1.26E-10 -1.76E-10 -8.30E-11 -1.14E-10 -8.40E-11 1.50E-11 4.60E-11 4.98E-10 -4.90E-11 -1.60E-11 100 -3.90E-11 3.87E-10 -3.06E-10 -5.98E-10 -8.10E-11 -1.63E-10 -2.10E-10 -1.60E-11 -1.12E-10 6.76E-10 -4.50E-11 -8.00E-12 200 1.22E-10 5.76E-10 -7.39E-10 -8.15E-10 -2.70E-11 -4.91E-10 -2.75E-10 -1.12E-10 -6.26E-10 1.02E-09 -4.90E-11 -2.00E-12 Biased Statistics Average Biased -6.40E-12 -2.98E-11 -2.20E-11 -1.27E-10 -1.77E-10 Std Dev Biased 9.79E-11 1.03E-10 1.34E-10 3.63E-10 5.92E-10 Ps90%/90% (+KTL) Biased 2.62E-10 2.54E-10 3.44E-10 8.69E-10 1.45E-09 Ps90%/90% (-KTL) Biased -2.75E-10 -3.13E-10 -3.88E-10 -1.12E-09 -1.80E-09 Un-Biased Statistics Average Un-Biased 5.58E-11 5.12E-11 7.22E-11 3.50E-11 -9.64E-11 Std Dev Un-Biased 1.40E-10 2.15E-10 2.47E-10 3.65E-10 6.56E-10 Ps90%/90% (+KTL) Un-Biased 4.38E-10 6.41E-10 7.50E-10 1.04E-09 1.70E-09 Ps90%/90% (-KTL) Un-Biased -3.27E-10 -5.38E-10 -6.05E-10 -9.67E-10 -1.89E-09 Specification MIN -1.00E-08 -1.00E-08 -1.50E-08 -2.00E-08 -2.50E-08 Status PASS PASS PASS PASS PASS Specification MAX 1.00E-08 1.00E-08 1.50E-08 2.00E-08 2.50E-08 Status PASS PASS PASS PASS PASS An ISO 9001:2008 and DSCC Certified Company 16 RLAT Report 10-055 100219 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Input Offset Current CH B (A) 3.00E-08 2.00E-08 1.00E-08 0.00E+00 -1.00E-08 -2.00E-08 -3.00E-08 0 50 100 150 Total Dose (krad(Si)) Figure 5.6. Plot of Input Offset Current CH B (A) versus total dose. The data show no significant change with total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 17 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 10-055 100219 R1.1 Table 5.6. Raw data for Input Offset Current CH B (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Input Offset Current CH B (A) Device 41 116 182 241 325 408 492 724 786 868 929 1012 Total Dose (krad(Si)) 0 -1.22E-10 0.00E+00 1.40E-11 -4.20E-11 -4.00E-12 -1.25E-10 3.30E-11 2.06E-10 -1.80E-11 -1.22E-10 -6.60E-11 -1.00E-10 20 -9.40E-11 6.60E-11 -2.00E-12 7.30E-11 3.00E-12 -6.20E-11 -3.10E-11 4.20E-11 -9.00E-11 -7.20E-11 -5.70E-11 -9.90E-11 50 -1.60E-10 -9.40E-11 -6.30E-11 -9.80E-11 1.42E-10 -1.68E-10 -6.10E-11 -4.90E-11 -2.68E-10 -8.00E-11 -8.10E-11 -1.19E-10 100 -1.58E-10 -7.00E-12 -4.70E-11 -1.88E-10 -8.00E-12 -3.56E-10 -2.72E-10 -3.69E-10 -5.03E-10 -7.00E-11 -7.40E-11 -9.20E-11 200 -5.00E-11 -1.78E-10 -5.11E-10 -4.37E-10 9.90E-11 -9.87E-10 -3.37E-10 -6.28E-10 -9.99E-10 -3.43E-10 -9.00E-11 -1.25E-10 Biased Statistics Average Biased -3.08E-11 9.20E-12 -5.46E-11 -8.16E-11 -2.15E-10 Std Dev Biased 5.50E-11 6.73E-11 1.15E-10 8.56E-11 2.57E-10 Ps90%/90% (+KTL) Biased 1.20E-10 1.94E-10 2.62E-10 1.53E-10 4.89E-10 Ps90%/90% (-KTL) Biased -1.82E-10 -1.75E-10 -3.71E-10 -3.16E-10 -9.20E-10 Un-Biased Statistics Average Un-Biased -5.20E-12 -4.26E-11 -1.25E-10 -3.14E-10 -6.59E-10 Std Dev Un-Biased 1.36E-10 5.19E-11 9.25E-11 1.60E-10 3.27E-10 Ps90%/90% (+KTL) Un-Biased 3.68E-10 9.97E-11 1.28E-10 1.23E-10 2.38E-10 Ps90%/90% (-KTL) Un-Biased -3.79E-10 -1.85E-10 -3.79E-10 -7.51E-10 -1.56E-09 Specification MIN -1.00E-08 -1.00E-08 -1.50E-08 -2.00E-08 -2.50E-08 Status PASS PASS PASS PASS PASS Specification MAX 1.00E-08 1.00E-08 1.50E-08 2.00E-08 2.50E-08 Status PASS PASS PASS PASS PASS An ISO 9001:2008 and DSCC Certified Company 18 RLAT Report 10-055 100219 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX + Input Bias Current CH A (A) 3.00E-07 2.00E-07 1.00E-07 0.00E+00 -1.00E-07 -2.00E-07 -3.00E-07 0 50 100 150 Total Dose (krad(Si)) Figure 5.7. Plot of input bias current, non-inverting input @ +/-15V (A) for channel A versus total dose. The data show an increase with radiation, however it is not sufficient to cause the parameter to exceed the postradiation specification, even after application of the KTL statistics. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black lines show the effects on the data after application of the biased KTL statistics (solid and dashed lines) while the gray lines show the effects on the data after application of the unbiased KTL statistics (solid and dashed lines). The red dashed lines are the minimum and maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 19 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 10-055 100219 R1.1 Table 5.7. Raw data for + Input Bias Current CH A (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). + Input Bias Current CH A (A) Device 41 116 182 241 325 408 492 724 786 868 929 1012 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status Total Dose (krad(Si)) 0 1.09E-08 1.17E-08 1.18E-08 1.24E-08 1.13E-08 1.14E-08 1.05E-08 1.17E-08 1.24E-08 1.06E-08 1.15E-08 1.11E-08 20 1.42E-08 1.46E-08 1.51E-08 1.59E-08 1.43E-08 1.47E-08 1.35E-08 1.50E-08 1.60E-08 1.39E-08 1.16E-08 1.11E-08 50 2.10E-08 2.09E-08 2.21E-08 2.35E-08 2.06E-08 2.10E-08 1.96E-08 2.15E-08 2.27E-08 2.01E-08 1.15E-08 1.11E-08 100 3.22E-08 3.21E-08 3.41E-08 3.57E-08 3.15E-08 3.15E-08 2.95E-08 3.20E-08 3.35E-08 3.06E-08 1.16E-08 1.11E-08 200 5.22E-08 5.35E-08 5.52E-08 5.81E-08 5.04E-08 5.04E-08 4.80E-08 5.14E-08 5.39E-08 4.92E-08 1.16E-08 1.11E-08 1.16E-08 5.64E-10 1.32E-08 1.01E-08 1.48E-08 7.27E-10 1.68E-08 1.28E-08 2.16E-08 1.19E-09 2.49E-08 1.83E-08 3.31E-08 1.75E-09 3.79E-08 2.83E-08 5.39E-08 2.96E-09 6.20E-08 4.58E-08 1.13E-08 1.46E-08 2.10E-08 3.14E-08 5.06E-08 7.74E-10 9.67E-10 1.19E-09 1.49E-09 2.28E-09 1.34E-08 1.73E-08 2.42E-08 3.55E-08 5.68E-08 9.19E-09 1.20E-08 1.77E-08 2.73E-08 4.43E-08 -3.00E-08 -7.50E-08 -1.00E-07 -1.75E-07 -2.50E-07 PASS PASS PASS PASS PASS 3.00E-08 7.50E-08 1.00E-07 1.75E-07 2.50E-07 PASS PASS PASS PASS PASS An ISO 9001:2008 and DSCC Certified Company 20 RLAT Report 10-055 100219 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX + Input Bias Current CH B (A) 3.00E-07 2.00E-07 1.00E-07 0.00E+00 -1.00E-07 -2.00E-07 -3.00E-07 0 50 100 150 Total Dose (krad(Si)) Figure 5.8. Plot of input bias current, non-inverting input @ +/-15V (A) for channel B versus total dose. The data show an increase with radiation, however it is not sufficient to cause the parameter to exceed the postradiation specification, even after application of the KTL statistics. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black lines show the effects on the data after application of the biased KTL statistics (solid and dashed lines) while the gray lines show the effects on the data after application of the unbiased KTL statistics (solid and dashed lines). The red dashed lines are the minimum and maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 21 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 10-055 100219 R1.1 Table 5.8. Raw data for + Input Bias Current CH B (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). + Input Bias Current CH B (A) Device 41 116 182 241 325 408 492 724 786 868 929 1012 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status Total Dose (krad(Si)) 0 1.12E-08 1.21E-08 1.23E-08 1.30E-08 1.17E-08 1.24E-08 1.09E-08 1.27E-08 1.21E-08 1.16E-08 1.19E-08 1.14E-08 20 1.47E-08 1.50E-08 1.57E-08 1.68E-08 1.49E-08 1.59E-08 1.40E-08 1.63E-08 1.57E-08 1.50E-08 1.19E-08 1.14E-08 50 2.18E-08 2.17E-08 2.30E-08 2.47E-08 2.12E-08 2.28E-08 2.04E-08 2.33E-08 2.25E-08 2.16E-08 1.19E-08 1.14E-08 100 3.34E-08 3.33E-08 3.51E-08 3.74E-08 3.24E-08 3.42E-08 3.09E-08 3.51E-08 3.35E-08 3.26E-08 1.19E-08 1.14E-08 200 5.39E-08 5.52E-08 5.72E-08 6.09E-08 5.18E-08 5.48E-08 5.03E-08 5.59E-08 5.39E-08 5.24E-08 1.19E-08 1.14E-08 1.21E-08 6.69E-10 1.39E-08 1.03E-08 1.54E-08 8.37E-10 1.77E-08 1.31E-08 2.25E-08 1.41E-09 2.64E-08 1.87E-08 3.43E-08 1.98E-09 3.97E-08 2.89E-08 5.58E-08 3.47E-09 6.53E-08 4.63E-08 1.19E-08 1.54E-08 2.21E-08 3.33E-08 5.35E-08 7.28E-10 8.81E-10 1.16E-09 1.59E-09 2.21E-09 1.39E-08 1.78E-08 2.53E-08 3.76E-08 5.95E-08 9.93E-09 1.30E-08 1.89E-08 2.89E-08 4.74E-08 -3.00E-08 -7.50E-08 -1.00E-07 -1.75E-07 -2.50E-07 PASS PASS PASS PASS PASS 3.00E-08 7.50E-08 1.00E-07 1.75E-07 2.50E-07 PASS PASS PASS PASS PASS An ISO 9001:2008 and DSCC Certified Company 22 RLAT Report 10-055 100219 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX - Input Bias Current CH A (A) 3.00E-07 2.00E-07 1.00E-07 0.00E+00 -1.00E-07 -2.00E-07 -3.00E-07 0 50 100 150 Total Dose (krad(Si)) Figure 5.9. Plot of input bias current, inverting input @ +/-15V for channel A versus total dose. The data show an increase with radiation, however it is not sufficient to cause the parameter to exceed the post-radiation specification, even after application of the KTL statistics. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black lines show the effects on the data after application of the biased KTL statistics (solid and dashed lines) while the gray lines show the effects on the data after application of the unbiased KTL statistics (solid and dashed lines). The red dashed lines are the minimum and maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 23 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 10-055 100219 R1.1 Table 5.9. Raw data for - Input Bias Current CH A (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). - Input Bias Current CH A (A) Device 41 116 182 241 325 408 492 724 786 868 929 1012 Total Dose (krad(Si)) 0 1.07E-08 1.18E-08 1.19E-08 1.23E-08 1.13E-08 1.12E-08 1.05E-08 1.18E-08 1.23E-08 1.09E-08 1.15E-08 1.11E-08 20 1.40E-08 1.46E-08 1.52E-08 1.58E-08 1.44E-08 1.45E-08 1.35E-08 1.51E-08 1.59E-08 1.43E-08 1.15E-08 1.11E-08 50 2.09E-08 2.11E-08 2.23E-08 2.33E-08 2.06E-08 2.08E-08 1.95E-08 2.15E-08 2.27E-08 2.07E-08 1.15E-08 1.11E-08 100 3.22E-08 3.26E-08 3.39E-08 3.52E-08 3.15E-08 3.14E-08 2.94E-08 3.22E-08 3.35E-08 3.14E-08 1.15E-08 1.11E-08 200 5.24E-08 5.42E-08 5.45E-08 5.75E-08 5.04E-08 5.02E-08 4.79E-08 5.14E-08 5.35E-08 5.03E-08 1.15E-08 1.11E-08 Biased Statistics Average Biased 1.16E-08 1.48E-08 2.16E-08 3.31E-08 5.38E-08 Std Dev Biased 6.08E-10 7.34E-10 1.13E-09 1.48E-09 2.63E-09 Ps90%/90% (+KTL) Biased 1.33E-08 1.68E-08 2.47E-08 3.71E-08 6.10E-08 Ps90%/90% (-KTL) Biased 9.92E-09 1.28E-08 1.85E-08 2.90E-08 4.66E-08 Un-Biased Statistics Average Un-Biased 1.13E-08 1.47E-08 2.10E-08 3.16E-08 5.07E-08 Std Dev Un-Biased 7.28E-10 9.18E-10 1.17E-09 1.49E-09 2.06E-09 Ps90%/90% (+KTL) Un-Biased 1.33E-08 1.72E-08 2.43E-08 3.56E-08 5.63E-08 Ps90%/90% (-KTL) Un-Biased 9.34E-09 1.21E-08 1.78E-08 2.75E-08 4.50E-08 Specification MIN -3.00E-08 -7.50E-08 -1.00E-07 -1.75E-07 -2.50E-07 Status PASS PASS PASS PASS PASS Specification MAX 3.00E-08 7.50E-08 1.00E-07 1.75E-07 2.50E-07 Status PASS PASS PASS PASS PASS An ISO 9001:2008 and DSCC Certified Company 24 RLAT Report 10-055 100219 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX - Input Bias Current CH B (A) 3.00E-07 2.00E-07 1.00E-07 0.00E+00 -1.00E-07 -2.00E-07 -3.00E-07 0 50 100 150 Total Dose (krad(Si)) Figure 5.10. Plot of input bias current, inverting input @ +/-15V for channel B versus total dose. The data show an increase with radiation, however it is not sufficient to cause the parameter to exceed the post-radiation specification, even after application of the KTL statistics. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black lines show the effects on the data after application of the biased KTL statistics (solid and dashed lines) while the gray lines show the effects on the data after application of the unbiased KTL statistics (solid and dashed lines). The red dashed lines are the minimum and maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 25 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 10-055 100219 R1.1 Table 5.10. Raw data for - Input Bias Current CH B (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). - Input Bias Current CH B (A) Device 41 116 182 241 325 408 492 724 786 868 929 1012 Total Dose (krad(Si)) 0 1.11E-08 1.21E-08 1.23E-08 1.30E-08 1.17E-08 1.22E-08 1.08E-08 1.27E-08 1.21E-08 1.14E-08 1.18E-08 1.13E-08 20 1.46E-08 1.51E-08 1.57E-08 1.68E-08 1.49E-08 1.59E-08 1.40E-08 1.63E-08 1.57E-08 1.49E-08 1.18E-08 1.13E-08 50 2.17E-08 2.16E-08 2.30E-08 2.46E-08 2.13E-08 2.28E-08 2.03E-08 2.33E-08 2.23E-08 2.16E-08 1.18E-08 1.13E-08 100 3.33E-08 3.33E-08 3.52E-08 3.73E-08 3.25E-08 3.40E-08 3.07E-08 3.48E-08 3.30E-08 3.26E-08 1.18E-08 1.13E-08 200 5.39E-08 5.52E-08 5.68E-08 6.07E-08 5.20E-08 5.40E-08 5.02E-08 5.54E-08 5.31E-08 5.22E-08 1.18E-08 1.13E-08 Biased Statistics Average Biased 1.20E-08 1.54E-08 2.24E-08 3.43E-08 5.57E-08 Std Dev Biased 7.03E-10 8.89E-10 1.36E-09 1.93E-09 3.29E-09 Ps90%/90% (+KTL) Biased 1.39E-08 1.79E-08 2.62E-08 3.96E-08 6.48E-08 Ps90%/90% (-KTL) Biased 1.01E-08 1.30E-08 1.87E-08 2.90E-08 4.67E-08 Un-Biased Statistics Average Un-Biased 1.19E-08 1.54E-08 2.21E-08 3.30E-08 5.30E-08 Std Dev Un-Biased 7.32E-10 9.01E-10 1.15E-09 1.53E-09 1.97E-09 Ps90%/90% (+KTL) Un-Biased 1.39E-08 1.78E-08 2.52E-08 3.72E-08 5.84E-08 Ps90%/90% (-KTL) Un-Biased 9.85E-09 1.29E-08 1.89E-08 2.88E-08 4.76E-08 Specification MIN -3.00E-08 -7.50E-08 -1.00E-07 -1.75E-07 -2.50E-07 Status PASS PASS PASS PASS PASS Specification MAX 3.00E-08 7.50E-08 1.00E-07 1.75E-07 2.50E-07 Status PASS PASS PASS PASS PASS An ISO 9001:2008 and DSCC Certified Company 26 RLAT Report 10-055 100219 R1.1 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (-KTL) Biased Common Mode Rejection Ratio CH A (dB) 1.30E+02 1.20E+02 1.10E+02 1.00E+02 9.00E+01 8.00E+01 7.00E+01 6.00E+01 0 50 100 150 Total Dose (krad(Si)) Figure 5.11. Plot of common mode rejection ratio for channel A versus total dose. Although the data show a significant decrease with total dose, the parameter does not fall below the specification value. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black lines show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray lines show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed lines are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 27 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 10-055 100219 R1.1 Table 5.11. Raw data for Common Mode Rejection Ratio CH A (dB) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Common Mode Rejection Ratio CH A (dB) Device 41 116 182 241 325 408 492 724 786 868 929 1012 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Total Dose (krad(Si)) 0 1.23E+02 1.10E+02 1.20E+02 1.21E+02 1.14E+02 1.15E+02 1.26E+02 1.14E+02 1.15E+02 1.09E+02 1.18E+02 1.18E+02 20 1.18E+02 1.09E+02 1.16E+02 1.18E+02 1.12E+02 1.14E+02 1.20E+02 1.12E+02 1.13E+02 1.09E+02 1.18E+02 1.18E+02 50 1.16E+02 1.09E+02 1.15E+02 1.15E+02 1.11E+02 1.13E+02 1.16E+02 1.10E+02 1.11E+02 1.08E+02 1.18E+02 1.18E+02 100 1.14E+02 1.08E+02 1.13E+02 1.13E+02 1.10E+02 1.11E+02 1.14E+02 1.09E+02 1.10E+02 1.07E+02 1.18E+02 1.18E+02 200 1.12E+02 1.08E+02 1.11E+02 1.11E+02 1.09E+02 1.09E+02 1.11E+02 1.07E+02 1.08E+02 1.07E+02 1.18E+02 1.18E+02 1.18E+02 5.33E+00 1.32E+02 1.03E+02 1.15E+02 3.82E+00 1.25E+02 1.04E+02 1.13E+02 3.05E+00 1.22E+02 1.05E+02 1.12E+02 2.32E+00 1.18E+02 1.05E+02 1.10E+02 1.67E+00 1.15E+02 1.05E+02 1.16E+02 1.13E+02 1.12E+02 1.10E+02 1.08E+02 6.08E+00 4.02E+00 3.11E+00 2.35E+00 1.75E+00 1.32E+02 1.24E+02 1.20E+02 1.16E+02 1.13E+02 9.90E+01 1.02E+02 1.03E+02 1.04E+02 1.03E+02 9.70E+01 9.70E+01 9.40E+01 9.00E+01 8.60E+01 PASS PASS PASS PASS PASS An ISO 9001:2008 and DSCC Certified Company 28 RLAT Report 10-055 100219 R1.1 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (-KTL) Biased Common Mode Rejection Ratio CH B (dB) 1.30E+02 1.20E+02 1.10E+02 1.00E+02 9.00E+01 8.00E+01 7.00E+01 6.00E+01 0 50 100 150 Total Dose (krad(Si)) Figure 5.12. Plot of common mode rejection ratio for channel B versus total dose. Although the data show a significant decrease with total dose, the parameter does not fall below the specification value. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black lines show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray lines show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed lines are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 29 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 10-055 100219 R1.1 Table 5.12. Raw data for Common Mode Rejection Ratio CH B (dB) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Common Mode Rejection Ratio CH B (dB) Device 41 116 182 241 325 408 492 724 786 868 929 1012 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Total Dose (krad(Si)) 0 1.13E+02 1.15E+02 1.14E+02 1.20E+02 1.14E+02 1.19E+02 1.21E+02 1.13E+02 1.11E+02 1.28E+02 1.14E+02 1.16E+02 20 1.11E+02 1.14E+02 1.12E+02 1.17E+02 1.13E+02 1.16E+02 1.18E+02 1.12E+02 1.10E+02 1.26E+02 1.14E+02 1.16E+02 50 1.11E+02 1.13E+02 1.11E+02 1.15E+02 1.12E+02 1.14E+02 1.15E+02 1.10E+02 1.09E+02 1.25E+02 1.14E+02 1.16E+02 100 1.09E+02 1.12E+02 1.10E+02 1.14E+02 1.11E+02 1.12E+02 1.13E+02 1.09E+02 1.07E+02 1.25E+02 1.14E+02 1.16E+02 200 1.08E+02 1.10E+02 1.09E+02 1.12E+02 1.10E+02 1.10E+02 1.10E+02 1.08E+02 1.06E+02 1.18E+02 1.14E+02 1.16E+02 1.15E+02 2.80E+00 1.23E+02 1.08E+02 1.13E+02 2.13E+00 1.19E+02 1.08E+02 1.12E+02 1.77E+00 1.17E+02 1.07E+02 1.11E+02 1.71E+00 1.16E+02 1.06E+02 1.10E+02 1.37E+00 1.14E+02 1.06E+02 1.19E+02 1.16E+02 1.15E+02 1.13E+02 1.10E+02 6.81E+00 6.25E+00 6.52E+00 6.89E+00 4.56E+00 1.37E+02 1.33E+02 1.33E+02 1.32E+02 1.23E+02 9.99E+01 9.92E+01 9.68E+01 9.44E+01 9.79E+01 9.70E+01 9.70E+01 9.40E+01 9.00E+01 8.60E+01 PASS PASS PASS PASS PASS An ISO 9001:2008 and DSCC Certified Company 30 RLAT Report 10-055 100219 R1.1 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (-KTL) Biased Power Supply Rejection Ratio CH A (dB) 1.40E+02 1.30E+02 1.20E+02 1.10E+02 1.00E+02 9.00E+01 8.00E+01 7.00E+01 6.00E+01 0 50 100 150 Total Dose (krad(Si)) Figure 5.13. Plot of Power Supply Rejection Ratio CH A (dB) versus total dose. The data show no significant change with total dose (note that the KTL value is “out of specification pre-irradiation and at the 20krad(Si) and 50krad(Si) dose levels due to the distribution within the sample population). The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 31 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 10-055 100219 R1.1 Table 5.13. Raw data for Power Supply Rejection Ratio CH A (dB) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Power Supply Rejection Ratio CH A (dB) Device 41 116 182 241 325 408 492 724 786 868 929 1012 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Total Dose (krad(Si)) 0 1.41E+02 1.17E+02 1.35E+02 1.32E+02 1.23E+02 1.32E+02 1.28E+02 1.35E+02 1.33E+02 1.09E+02 1.42E+02 1.34E+02 20 1.33E+02 1.17E+02 1.44E+02 1.36E+02 1.24E+02 1.33E+02 1.29E+02 1.39E+02 1.29E+02 1.09E+02 1.41E+02 1.35E+02 50 1.30E+02 1.18E+02 1.42E+02 1.32E+02 1.25E+02 1.41E+02 1.31E+02 1.41E+02 1.25E+02 1.08E+02 1.43E+02 1.34E+02 100 1.26E+02 1.17E+02 1.34E+02 1.36E+02 1.26E+02 1.34E+02 1.44E+02 1.31E+02 1.22E+02 1.08E+02 1.44E+02 1.34E+02 200 1.21E+02 1.18E+02 1.24E+02 1.25E+02 1.33E+02 1.23E+02 1.24E+02 1.22E+02 1.17E+02 1.07E+02 1.44E+02 1.34E+02 1.29E+02 9.70E+00 1.56E+02 1.03E+02 1.31E+02 1.05E+01 1.60E+02 1.02E+02 1.29E+02 8.94E+00 1.54E+02 1.04E+02 1.28E+02 7.29E+00 1.48E+02 1.08E+02 1.24E+02 5.82E+00 1.40E+02 1.08E+02 1.27E+02 1.28E+02 1.29E+02 1.28E+02 1.18E+02 1.06E+01 1.15E+01 1.35E+01 1.36E+01 7.13E+00 1.56E+02 1.60E+02 1.66E+02 1.65E+02 1.38E+02 9.81E+01 9.63E+01 9.24E+01 9.04E+01 9.89E+01 1.00E+02 9.80E+01 9.40E+01 8.60E+01 8.00E+01 FAIL FAIL FAIL PASS PASS An ISO 9001:2008 and DSCC Certified Company 32 RLAT Report 10-055 100219 R1.1 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (-KTL) Biased Power Supply Rejection Ratio CH B (dB) 1.50E+02 1.40E+02 1.30E+02 1.20E+02 1.10E+02 1.00E+02 9.00E+01 8.00E+01 7.00E+01 6.00E+01 0 50 100 150 Total Dose (krad(Si)) Figure 5.14. Plot of Power Supply Rejection Ratio CH B (dB) versus total dose. The data show no significant change with total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 33 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 10-055 100219 R1.1 Table 5.14. Raw data for Power Supply Rejection Ratio CH B (dB) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Power Supply Rejection Ratio CH B (dB) Device 41 116 182 241 325 408 492 724 786 868 929 1012 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Total Dose (krad(Si)) 0 1.37E+02 1.30E+02 1.35E+02 1.26E+02 1.31E+02 1.49E+02 1.22E+02 1.40E+02 1.37E+02 1.24E+02 1.31E+02 1.28E+02 20 1.33E+02 1.32E+02 1.39E+02 1.27E+02 1.33E+02 1.36E+02 1.22E+02 1.38E+02 1.45E+02 1.24E+02 1.31E+02 1.29E+02 50 1.30E+02 1.36E+02 1.58E+02 1.29E+02 1.37E+02 1.29E+02 1.24E+02 1.31E+02 1.47E+02 1.25E+02 1.32E+02 1.29E+02 100 1.25E+02 1.41E+02 1.43E+02 1.33E+02 1.48E+02 1.25E+02 1.28E+02 1.26E+02 1.32E+02 1.28E+02 1.31E+02 1.29E+02 200 1.22E+02 1.49E+02 1.37E+02 1.31E+02 1.32E+02 1.19E+02 1.42E+02 1.19E+02 1.21E+02 1.37E+02 1.32E+02 1.29E+02 1.32E+02 4.35E+00 1.44E+02 1.20E+02 1.33E+02 4.17E+00 1.44E+02 1.21E+02 1.38E+02 1.17E+01 1.70E+02 1.06E+02 1.38E+02 8.88E+00 1.62E+02 1.14E+02 1.34E+02 9.63E+00 1.61E+02 1.08E+02 1.34E+02 1.33E+02 1.31E+02 1.28E+02 1.28E+02 1.12E+01 9.80E+00 9.32E+00 2.79E+00 1.11E+01 1.65E+02 1.60E+02 1.57E+02 1.35E+02 1.58E+02 1.03E+02 1.06E+02 1.06E+02 1.20E+02 9.73E+01 1.00E+02 9.80E+01 9.40E+01 8.60E+01 8.00E+01 PASS PASS PASS PASS PASS An ISO 9001:2008 and DSCC Certified Company 34 RLAT Report 10-055 100219 R1.1 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (-KTL) Biased Large Signal Voltage Gain CH A (V/mV) 1.00E+05 1.00E+04 1.00E+03 1.00E+02 1.00E+01 1.00E+00 0 50 100 150 Total Dose (krad(Si)) Figure 5.15. Plot of Large Signal Voltage Gain CH A (V/mV) versus total dose. The data show no significant change with total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 35 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 10-055 100219 R1.1 Table 5.15. Raw data for Large Signal Voltage Gain CH A (V/mV) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Large Signal Voltage Gain CH A (V/mV) Device 41 116 182 241 325 408 492 724 786 868 929 1012 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Total Dose (krad(Si)) 0 5.35E+04 5.82E+04 4.06E+04 5.20E+04 4.35E+04 4.52E+04 5.93E+04 5.12E+04 5.46E+04 4.76E+04 5.50E+04 5.81E+04 20 5.04E+04 5.03E+04 5.25E+04 5.12E+04 5.04E+04 4.49E+04 5.17E+04 5.58E+04 4.68E+04 5.33E+04 5.71E+04 5.78E+04 50 5.07E+04 5.25E+04 4.31E+04 5.35E+04 4.67E+04 4.66E+04 4.17E+04 4.15E+04 3.69E+04 5.16E+04 5.98E+04 5.23E+04 100 4.58E+04 4.78E+04 4.73E+04 4.27E+04 4.22E+04 4.08E+04 4.21E+04 3.25E+04 3.45E+04 4.08E+04 5.56E+04 5.54E+04 200 4.40E+04 4.55E+04 4.62E+04 4.80E+04 3.45E+04 2.67E+04 3.13E+04 2.96E+04 2.76E+04 3.97E+04 5.55E+04 5.68E+04 4.95E+04 7.29E+03 6.95E+04 2.95E+04 5.10E+04 9.25E+02 5.35E+04 4.84E+04 4.93E+04 4.32E+03 6.12E+04 3.74E+04 4.52E+04 2.56E+03 5.22E+04 3.81E+04 4.36E+04 5.29E+03 5.82E+04 2.91E+04 5.16E+04 5.05E+04 4.37E+04 3.82E+04 3.10E+04 5.60E+03 4.54E+03 5.62E+03 4.34E+03 5.16E+03 6.69E+04 6.30E+04 5.91E+04 5.01E+04 4.51E+04 3.62E+04 3.81E+04 2.82E+04 2.62E+04 1.68E+04 1.20E+03 2.00E+02 1.00E+02 5.00E+01 2.50E+01 PASS PASS PASS PASS PASS An ISO 9001:2008 and DSCC Certified Company 36 RLAT Report 10-055 100219 R1.1 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (-KTL) Biased Large Signal Voltage Gain CH B (V/mV) 1.00E+05 1.00E+04 1.00E+03 1.00E+02 1.00E+01 1.00E+00 0 50 100 150 Total Dose (krad(Si)) Figure 5.16. Plot of Large Signal Voltage Gain CH B (V/mV) versus total dose. The data show no significant change with total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 37 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 10-055 100219 R1.1 Table 5.16. Raw data for Large Signal Voltage Gain CH B (V/mV) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Large Signal Voltage Gain CH B (V/mV) Device 41 116 182 241 325 408 492 724 786 868 929 1012 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Total Dose (krad(Si)) 0 5.22E+04 5.43E+04 5.01E+04 5.30E+04 5.13E+04 5.10E+04 4.94E+04 3.23E+04 4.76E+04 5.53E+04 5.22E+04 5.50E+04 20 5.50E+04 5.40E+04 5.39E+04 4.84E+04 4.91E+04 5.28E+04 5.12E+04 5.44E+04 4.70E+04 5.46E+04 5.39E+04 5.56E+04 50 4.90E+04 4.86E+04 4.59E+04 5.21E+04 4.49E+04 4.15E+04 4.72E+04 4.59E+04 4.39E+04 4.68E+04 5.60E+04 5.35E+04 100 4.52E+04 4.73E+04 4.78E+04 4.53E+04 4.57E+04 3.43E+04 3.96E+04 3.50E+04 4.29E+04 4.17E+04 5.68E+04 5.91E+04 200 3.66E+04 4.20E+04 4.96E+04 4.08E+04 4.27E+04 3.14E+04 3.21E+04 3.07E+04 3.66E+04 3.72E+04 5.51E+04 5.77E+04 5.22E+04 1.62E+03 5.66E+04 4.78E+04 5.21E+04 3.06E+03 6.05E+04 4.37E+04 4.81E+04 2.83E+03 5.59E+04 4.04E+04 4.62E+04 1.20E+03 4.95E+04 4.29E+04 4.23E+04 4.69E+03 5.52E+04 2.95E+04 4.71E+04 5.20E+04 4.51E+04 3.87E+04 3.36E+04 8.77E+03 3.11E+03 2.39E+03 3.88E+03 3.06E+03 7.12E+04 6.05E+04 5.16E+04 4.93E+04 4.20E+04 2.31E+04 4.35E+04 3.85E+04 2.80E+04 2.52E+04 1.20E+03 2.00E+02 1.00E+02 5.00E+01 2.50E+01 PASS PASS PASS PASS PASS An ISO 9001:2008 and DSCC Certified Company 38 RLAT Report 10-055 100219 R1.1 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (-KTL) Biased Positive Output Voltage Swing CH A (V) 1.42E+01 1.40E+01 1.38E+01 1.36E+01 1.34E+01 1.32E+01 1.30E+01 1.28E+01 1.26E+01 1.24E+01 0 50 100 150 Total Dose (krad(Si)) Figure 5.17. Plot of Positive Output Voltage Swing CH A (V) versus total dose. The data show no significant change with total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 39 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 10-055 100219 R1.1 Table 5.17. Raw data for Positive Output Voltage Swing CH A (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Output Voltage Swing CH A (V) Device 41 116 182 241 325 408 492 724 786 868 929 1012 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Total Dose (krad(Si)) 0 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 20 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 50 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 100 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 200 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 5.50E-03 1.40E+01 1.40E+01 1.40E+01 5.79E-03 1.40E+01 1.40E+01 1.40E+01 6.02E-03 1.40E+01 1.40E+01 1.40E+01 5.94E-03 1.40E+01 1.40E+01 1.40E+01 6.26E-03 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.13E-02 1.15E-02 1.09E-02 1.17E-02 1.19E-02 1.40E+01 1.41E+01 1.40E+01 1.41E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.25E+01 1.25E+01 1.25E+01 1.25E+01 1.25E+01 PASS PASS PASS PASS PASS An ISO 9001:2008 and DSCC Certified Company 40 RLAT Report 10-055 100219 R1.1 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (-KTL) Biased Positive Output Voltage Swing CH B (V) 1.42E+01 1.40E+01 1.38E+01 1.36E+01 1.34E+01 1.32E+01 1.30E+01 1.28E+01 1.26E+01 1.24E+01 0 50 100 150 Total Dose (krad(Si)) Figure 5.18. Plot of Positive Output Voltage Swing CH B (V) versus total dose. The data show no significant change with total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 41 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 10-055 100219 R1.1 Table 5.18. Raw data for Positive Output Voltage Swing CH B (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Output Voltage Swing CH B (V) Device 41 116 182 241 325 408 492 724 786 868 929 1012 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Total Dose (krad(Si)) 0 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 20 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 50 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 100 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 200 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 5.54E-03 1.40E+01 1.40E+01 1.40E+01 6.04E-03 1.40E+01 1.40E+01 1.40E+01 6.04E-03 1.40E+01 1.40E+01 1.40E+01 5.48E-03 1.40E+01 1.40E+01 1.40E+01 6.20E-03 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.04E-02 1.07E-02 1.09E-02 1.04E-02 1.13E-02 1.40E+01 1.41E+01 1.41E+01 1.41E+01 1.41E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.40E+01 1.25E+01 1.25E+01 1.25E+01 1.25E+01 1.25E+01 PASS PASS PASS PASS PASS An ISO 9001:2008 and DSCC Certified Company 42 RLAT Report 10-055 100219 R1.1 Average Biased Average Un-Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (+KTL) Biased Negative Output Voltage Swing CH A (V) -1.20E+01 -1.25E+01 -1.30E+01 -1.35E+01 -1.40E+01 -1.45E+01 -1.50E+01 0 50 100 150 Total Dose (krad(Si)) Figure 5.19. Plot of Negative Output Voltage Swing CH A (V) versus total dose. The data show no significant change with total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 43 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 10-055 100219 R1.1 Table 5.19. Raw data for Negative Output Voltage Swing CH A (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Output Voltage Swing CH A (V) Device 41 116 182 241 325 408 492 724 786 868 929 1012 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MAX Status Total Dose (krad(Si)) 0 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 20 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 50 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 100 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 200 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 2.28E-03 -1.44E+01 -1.44E+01 -1.44E+01 2.28E-03 -1.44E+01 -1.44E+01 -1.44E+01 2.35E-03 -1.44E+01 -1.44E+01 -1.44E+01 2.61E-03 -1.44E+01 -1.44E+01 -1.44E+01 2.61E-03 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 2.24E-03 2.61E-03 2.97E-03 3.65E-03 5.31E-03 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.25E+01 -1.25E+01 -1.25E+01 -1.25E+01 -1.25E+01 PASS PASS PASS PASS PASS An ISO 9001:2008 and DSCC Certified Company 44 RLAT Report 10-055 100219 R1.1 Average Biased Average Un-Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (+KTL) Biased Negative Output Voltage Swing CH B (V) -1.20E+01 -1.25E+01 -1.30E+01 -1.35E+01 -1.40E+01 -1.45E+01 -1.50E+01 0 50 100 150 Total Dose (krad(Si)) Figure 5.20. Plot of Negative Output Voltage Swing CH B (V) versus total dose. The data show no significant change with total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 45 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 10-055 100219 R1.1 Table 5.20. Raw data for Negative Output Voltage Swing CH B (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Output Voltage Swing CH B (V) Device 41 116 182 241 325 408 492 724 786 868 929 1012 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MAX Status Total Dose (krad(Si)) 0 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 20 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 50 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 100 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 200 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 2.65E-03 -1.44E+01 -1.44E+01 -1.44E+01 2.28E-03 -1.44E+01 -1.44E+01 -1.44E+01 2.17E-03 -1.44E+01 -1.44E+01 -1.44E+01 2.61E-03 -1.44E+01 -1.44E+01 -1.44E+01 2.49E-03 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 3.42E-03 3.77E-03 4.10E-03 4.69E-03 6.10E-03 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.44E+01 -1.25E+01 -1.25E+01 -1.25E+01 -1.25E+01 -1.25E+01 PASS PASS PASS PASS PASS An ISO 9001:2008 and DSCC Certified Company 46 RLAT Report 10-055 100219 R1.1 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (-KTL) Biased 5.00E-01 Positive Slew Rate CH A (V/µs) 4.50E-01 4.00E-01 3.50E-01 3.00E-01 2.50E-01 2.00E-01 1.50E-01 1.00E-01 5.00E-02 0.00E+00 0 50 100 150 Total Dose (krad(Si)) Figure 5.21. Plot of positive slew rate for channel A versus total dose. The data show a moderate decrease with total dose, however not sufficient to case the parameter to fall below the specification, even after application of the KTL statistics. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the unbiased sample. The black lines show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray lines show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed lines are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 47 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 10-055 100219 R1.1 Table 5.21. Raw data for Positive Slew Rate CH A (V/µs) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Slew Rate CH A (V/µs) Device 41 116 182 241 325 408 492 724 786 868 929 1012 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Total Dose (krad(Si)) 0 4.55E-01 4.59E-01 4.85E-01 4.75E-01 4.36E-01 4.37E-01 4.55E-01 4.42E-01 4.34E-01 5.06E-01 4.73E-01 4.91E-01 20 4.40E-01 4.55E-01 4.71E-01 4.73E-01 4.32E-01 4.17E-01 4.54E-01 4.44E-01 4.26E-01 5.15E-01 4.76E-01 4.84E-01 50 4.24E-01 4.51E-01 4.57E-01 4.56E-01 4.24E-01 4.03E-01 4.30E-01 4.24E-01 4.06E-01 4.81E-01 4.74E-01 4.94E-01 100 4.04E-01 4.22E-01 4.34E-01 4.40E-01 4.00E-01 3.79E-01 4.08E-01 4.03E-01 3.89E-01 4.64E-01 4.79E-01 4.86E-01 200 3.67E-01 3.77E-01 3.93E-01 3.97E-01 3.67E-01 3.26E-01 3.61E-01 3.54E-01 3.47E-01 4.21E-01 4.76E-01 4.94E-01 4.62E-01 1.89E-02 5.14E-01 4.10E-01 4.54E-01 1.82E-02 5.04E-01 4.04E-01 4.42E-01 1.69E-02 4.89E-01 3.96E-01 4.20E-01 1.77E-02 4.69E-01 3.71E-01 3.80E-01 1.42E-02 4.19E-01 3.41E-01 4.55E-01 4.51E-01 4.29E-01 4.09E-01 3.62E-01 2.97E-02 3.85E-02 3.14E-02 3.30E-02 3.56E-02 5.36E-01 5.57E-01 5.15E-01 4.99E-01 4.59E-01 3.73E-01 3.46E-01 3.43E-01 3.18E-01 2.64E-01 2.00E-01 1.20E-01 1.10E-01 7.00E-02 1.00E-02 PASS PASS PASS PASS PASS An ISO 9001:2008 and DSCC Certified Company 48 RLAT Report 10-055 100219 R1.1 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (-KTL) Biased Positive Slew Rate CH B (V/µs) 6.00E-01 5.00E-01 4.00E-01 3.00E-01 2.00E-01 1.00E-01 0.00E+00 0 50 100 150 200 Total Dose (krad(Si)) Figure 5.22. Plot of positive slew rate for channel B versus total dose. The data show a moderate decrease with total dose, however not sufficient to case the parameter to fall below the specification, even after application of the KTL statistics. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the unbiased sample. The black lines show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray lines show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed lines are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 49 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 10-055 100219 R1.1 Table 5.22. Raw data for Positive Slew Rate CH B (V/µs) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Slew Rate CH B (V/µs) Device 41 116 182 241 325 408 492 724 786 868 929 1012 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Total Dose (krad(Si)) 0 4.74E-01 4.86E-01 5.05E-01 5.18E-01 4.68E-01 4.63E-01 4.84E-01 4.66E-01 4.50E-01 5.31E-01 5.05E-01 5.16E-01 20 4.69E-01 4.66E-01 4.87E-01 5.04E-01 4.60E-01 4.47E-01 4.74E-01 4.64E-01 4.44E-01 5.05E-01 5.08E-01 5.22E-01 50 4.52E-01 4.71E-01 4.78E-01 4.90E-01 4.47E-01 4.30E-01 4.67E-01 4.53E-01 4.36E-01 4.96E-01 4.93E-01 5.17E-01 100 4.31E-01 4.43E-01 4.58E-01 4.63E-01 4.30E-01 4.11E-01 4.29E-01 4.24E-01 4.07E-01 4.78E-01 5.00E-01 5.18E-01 200 3.87E-01 3.95E-01 4.21E-01 4.27E-01 3.90E-01 3.58E-01 3.88E-01 3.78E-01 3.63E-01 4.31E-01 4.99E-01 5.11E-01 4.90E-01 2.10E-02 5.48E-01 4.33E-01 4.77E-01 1.80E-02 5.27E-01 4.28E-01 4.68E-01 1.80E-02 5.17E-01 4.18E-01 4.45E-01 1.51E-02 4.87E-01 4.03E-01 4.04E-01 1.86E-02 4.55E-01 3.53E-01 4.79E-01 4.67E-01 4.56E-01 4.30E-01 3.84E-01 3.16E-02 2.47E-02 2.65E-02 2.84E-02 2.91E-02 5.65E-01 5.34E-01 5.29E-01 5.08E-01 4.63E-01 3.92E-01 3.99E-01 3.84E-01 3.52E-01 3.04E-01 2.00E-01 1.20E-01 1.10E-01 7.00E-02 1.00E-02 PASS PASS PASS PASS PASS An ISO 9001:2008 and DSCC Certified Company 50 RLAT Report 10-055 100219 R1.1 Average Biased Average Un-Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (+KTL) Biased Negative Slew Rate CH A (V/µs) 0.00E+00 -1.00E-01 -2.00E-01 -3.00E-01 -4.00E-01 -5.00E-01 -6.00E-01 0 50 100 150 Total Dose (krad(Si)) Figure 5.23. Plot of negative slew rate for channel A versus total dose. The data show a moderate increase with total dose, however not sufficient to exceed the specification, even after application of the KTL statistics. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black lines show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray lines show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed lines are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 51 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 10-055 100219 R1.1 Table 5.23. Raw data for Negative Slew Rate CH A (V/µs) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Slew Rate CH A (V/µs) Device 41 116 182 241 325 408 492 724 786 868 929 1012 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MAX Status Total Dose (krad(Si)) 0 -4.98E-01 -5.12E-01 -5.34E-01 -5.22E-01 -4.87E-01 -4.77E-01 -5.11E-01 -4.82E-01 -4.83E-01 -5.70E-01 -5.21E-01 -5.30E-01 20 -4.96E-01 -4.87E-01 -5.36E-01 -5.16E-01 -4.80E-01 -4.69E-01 -4.95E-01 -4.92E-01 -4.69E-01 -5.54E-01 -5.39E-01 -5.46E-01 50 -4.80E-01 -4.97E-01 -5.09E-01 -5.20E-01 -4.67E-01 -4.66E-01 -4.96E-01 -4.75E-01 -4.56E-01 -5.36E-01 -5.32E-01 -5.45E-01 100 -4.66E-01 -4.66E-01 -4.76E-01 -4.84E-01 -4.52E-01 -4.31E-01 -4.63E-01 -4.48E-01 -4.32E-01 -5.12E-01 -5.22E-01 -5.51E-01 200 -4.04E-01 -4.19E-01 -4.46E-01 -4.42E-01 -4.00E-01 -3.93E-01 -4.03E-01 -3.93E-01 -3.94E-01 -4.62E-01 -5.37E-01 -5.47E-01 -5.11E-01 1.87E-02 -4.59E-01 -5.62E-01 -5.03E-01 2.29E-02 -4.40E-01 -5.66E-01 -4.95E-01 2.14E-02 -4.36E-01 -5.53E-01 -4.69E-01 1.20E-02 -4.36E-01 -5.02E-01 -4.22E-01 2.12E-02 -3.64E-01 -4.80E-01 -5.05E-01 -4.96E-01 -4.86E-01 -4.57E-01 -4.09E-01 3.89E-02 3.48E-02 3.17E-02 3.33E-02 2.99E-02 -3.98E-01 -4.00E-01 -3.99E-01 -3.66E-01 -3.27E-01 -6.11E-01 -5.91E-01 -5.73E-01 -5.49E-01 -4.91E-01 -2.00E-01 -1.20E-01 -1.10E-01 -7.00E-02 -1.00E-02 PASS PASS PASS PASS PASS An ISO 9001:2008 and DSCC Certified Company 52 RLAT Report 10-055 100219 R1.1 Average Biased Average Un-Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (+KTL) Biased Negative Slew Rate CH B (V/µs) 0.00E+00 -1.00E-01 -2.00E-01 -3.00E-01 -4.00E-01 -5.00E-01 -6.00E-01 0 50 100 150 Total Dose (krad(Si)) Figure 5.24. Plot of negative slew rate for channel B versus total dose. The data show a moderate increase with total dose, however not sufficient to exceed the specification, even after application of the KTL statistics. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black lines show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray lines show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed lines are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 53 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 10-055 100219 R1.1 Table 5.24. Raw data for Negative Slew Rate CH B (V/µs) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Slew Rate CH B (V/µs) Device 41 116 182 241 325 408 492 724 786 868 929 1012 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MAX Status Total Dose (krad(Si)) 0 -5.32E-01 -5.35E-01 -5.52E-01 -5.66E-01 -5.19E-01 -5.07E-01 -5.30E-01 -5.18E-01 -4.94E-01 -5.90E-01 -5.66E-01 -5.87E-01 20 -5.23E-01 -5.44E-01 -5.49E-01 -5.56E-01 -5.09E-01 -5.01E-01 -5.20E-01 -5.10E-01 -4.94E-01 -5.91E-01 -5.67E-01 -5.68E-01 50 -5.18E-01 -5.24E-01 -5.47E-01 -5.47E-01 -5.12E-01 -4.84E-01 -5.31E-01 -5.05E-01 -4.70E-01 -5.65E-01 -5.56E-01 -5.70E-01 100 -4.79E-01 -4.94E-01 -5.09E-01 -5.30E-01 -4.78E-01 -4.67E-01 -4.95E-01 -4.70E-01 -4.54E-01 -5.39E-01 -5.55E-01 -5.82E-01 200 -4.35E-01 -4.46E-01 -4.73E-01 -4.81E-01 -4.33E-01 -3.99E-01 -4.36E-01 -4.19E-01 -4.08E-01 -4.86E-01 -5.67E-01 -5.78E-01 -5.41E-01 1.83E-02 -4.90E-01 -5.91E-01 -5.36E-01 1.96E-02 -4.83E-01 -5.90E-01 -5.30E-01 1.64E-02 -4.85E-01 -5.75E-01 -4.98E-01 2.19E-02 -4.38E-01 -5.58E-01 -4.54E-01 2.21E-02 -3.93E-01 -5.14E-01 -5.28E-01 -5.23E-01 -5.11E-01 -4.85E-01 -4.30E-01 3.72E-02 3.91E-02 3.80E-02 3.36E-02 3.44E-02 -4.26E-01 -4.16E-01 -4.07E-01 -3.93E-01 -3.35E-01 -6.30E-01 -6.31E-01 -6.15E-01 -5.77E-01 -5.24E-01 -2.00E-01 -1.20E-01 -1.10E-01 -7.00E-02 -1.00E-02 PASS PASS PASS PASS PASS An ISO 9001:2008 and DSCC Certified Company 54 RLAT Report 10-055 100219 R1.1 Average Biased Average Un-Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (+KTL) Biased Positive Supply Current @ VS=5V (A) 1.10E-03 1.00E-03 9.00E-04 8.00E-04 7.00E-04 6.00E-04 5.00E-04 4.00E-04 3.00E-04 0 50 100 150 Total Dose (krad(Si)) Figure 5.25. Plot of positive supply current at 5V versus total dose. The data show a slight decrease (improvement) with total dose. Note that this parameter is only specified to 100krad(Si) and the 200krad(Si) dose data is for reference only. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the unbiased sample. The black line(s) show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray line(s) show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed line(s) are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 55 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 10-055 100219 R1.1 Table 5.25. Raw data for Positive Supply Current @ VS=5V (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Supply Current @ VS=5V (A) Device 41 116 182 241 325 408 492 724 786 868 929 1012 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MAX Status Total Dose (krad(Si)) 0 6.94E-04 6.89E-04 7.35E-04 7.53E-04 6.85E-04 6.76E-04 6.99E-04 7.02E-04 6.96E-04 7.58E-04 7.20E-04 7.24E-04 20 6.83E-04 6.76E-04 7.24E-04 7.43E-04 6.74E-04 6.82E-04 7.01E-04 7.09E-04 7.00E-04 7.67E-04 7.24E-04 7.29E-04 50 6.56E-04 6.65E-04 6.97E-04 7.14E-04 6.59E-04 6.53E-04 6.70E-04 6.75E-04 6.67E-04 7.41E-04 7.21E-04 7.25E-04 100 5.90E-04 6.02E-04 6.30E-04 6.53E-04 5.94E-04 5.89E-04 6.03E-04 6.11E-04 6.02E-04 6.74E-04 7.24E-04 7.27E-04 200 4.89E-04 4.98E-04 5.29E-04 5.39E-04 4.94E-04 4.75E-04 4.83E-04 5.06E-04 4.88E-04 5.51E-04 7.25E-04 7.22E-04 7.11E-04 3.08E-05 7.96E-04 6.27E-04 7.00E-04 3.15E-05 7.86E-04 6.14E-04 6.78E-04 2.58E-05 7.49E-04 6.07E-04 6.14E-04 2.69E-05 6.88E-04 5.40E-04 5.10E-04 2.26E-05 5.72E-04 4.48E-04 7.06E-04 7.12E-04 6.81E-04 6.16E-04 5.01E-04 3.07E-05 3.24E-05 3.44E-05 3.35E-05 3.04E-05 7.90E-04 8.01E-04 7.76E-04 7.08E-04 5.84E-04 6.22E-04 6.23E-04 5.87E-04 5.24E-04 4.17E-04 1.00E-03 1.00E-03 1.00E-03 1.00E-03 1.00E-03 PASS PASS PASS PASS PASS An ISO 9001:2008 and DSCC Certified Company 56 RLAT Report 10-055 100219 R1.1 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (-KTL) Biased Negative Supply Current @ VS=5V (A) -3.00E-04 -4.00E-04 -5.00E-04 -6.00E-04 -7.00E-04 -8.00E-04 -9.00E-04 -1.00E-03 -1.10E-03 0 50 100 150 Total Dose (krad(Si)) Figure 5.26. Plot of the negative supply current at 5V versus total dose. The data show an increase (improvement) with total dose. Note that this parameter is only specified to 100krad(Si) and the 200krad(Si) dose data is for reference only. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the unbiased sample. The black line(s) show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray line(s) show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed line(s) are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 57 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 10-055 100219 R1.1 Table 5.26. Raw data for Negative Supply Current @ VS=5V (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Supply Current @ VS=5V (A) Device 41 116 182 241 325 408 492 724 786 868 929 1012 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Total Dose (krad(Si)) 0 -6.80E-04 -6.74E-04 -7.20E-04 -7.35E-04 -6.69E-04 -6.59E-04 -6.83E-04 -6.87E-04 -6.82E-04 -7.44E-04 -7.04E-04 -7.07E-04 20 -6.67E-04 -6.60E-04 -7.07E-04 -7.26E-04 -6.56E-04 -6.68E-04 -6.85E-04 -6.89E-04 -6.87E-04 -7.50E-04 -7.05E-04 -7.10E-04 50 -6.37E-04 -6.47E-04 -6.82E-04 -6.97E-04 -6.42E-04 -6.36E-04 -6.50E-04 -6.60E-04 -6.52E-04 -7.21E-04 -7.05E-04 -7.12E-04 100 -5.73E-04 -5.87E-04 -6.14E-04 -6.30E-04 -5.78E-04 -5.69E-04 -5.88E-04 -5.95E-04 -5.84E-04 -6.56E-04 -7.08E-04 -7.12E-04 200 -4.73E-04 -4.82E-04 -5.09E-04 -5.18E-04 -4.77E-04 -4.56E-04 -4.65E-04 -4.89E-04 -4.67E-04 -5.32E-04 -7.05E-04 -7.09E-04 -6.96E-04 2.99E-05 -6.14E-04 -7.77E-04 -6.83E-04 3.14E-05 -5.97E-04 -7.69E-04 -6.61E-04 2.68E-05 -5.88E-04 -7.34E-04 -5.96E-04 2.46E-05 -5.29E-04 -6.64E-04 -4.92E-04 2.03E-05 -4.36E-04 -5.48E-04 -6.91E-04 -6.96E-04 -6.64E-04 -5.98E-04 -4.82E-04 3.16E-05 3.14E-05 3.31E-05 3.36E-05 3.06E-05 -6.04E-04 -6.10E-04 -5.73E-04 -5.06E-04 -3.98E-04 -7.78E-04 -7.82E-04 -7.55E-04 -6.90E-04 -5.66E-04 -1.00E-03 -1.00E-03 -1.00E-03 -1.00E-03 -1.00E-03 PASS PASS PASS PASS PASS An ISO 9001:2008 and DSCC Certified Company 58 RLAT Report 10-055 100219 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Input Offset Voltage CH A @ VS=5V (V) 1.00E-03 8.00E-04 6.00E-04 4.00E-04 2.00E-04 0.00E+00 -2.00E-04 -4.00E-04 -6.00E-04 -8.00E-04 -1.00E-03 0 50 100 150 Total Dose (krad(Si)) Figure 5.27. Plot of input offset voltage at 5V for channel A versus total dose. The data show a slight increase with total dose, however not sufficient for the parameter to exceed specification, including after application of the KTL statistics. Note that this parameter is only specified to 100krad(Si) and the 200krad(Si) dose data is for reference only. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black line(s) show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray line(s) show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed line(s) are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 59 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 10-055 100219 R1.1 Table 5.27. Raw data for Input Offset Voltage CH A @ VS=5V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Input Offset Voltage CH A @ VS=5V (V) Device 41 116 182 241 325 408 492 724 786 868 929 1012 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status Total Dose (krad(Si)) 0 2.57E-05 -9.14E-05 -6.44E-05 -3.72E-05 -2.96E-05 -1.05E-04 -2.70E-05 -6.59E-05 -1.40E-04 -1.32E-04 -3.79E-05 1.52E-05 20 1.21E-05 -8.93E-05 -5.58E-05 -2.93E-05 -2.51E-05 -8.69E-05 -2.42E-05 -5.19E-05 -1.28E-04 -1.38E-04 -3.71E-05 1.47E-05 50 3.62E-05 -8.86E-05 -3.31E-05 -1.04E-05 -8.94E-06 -5.16E-05 -1.69E-06 -2.39E-05 -9.06E-05 -1.51E-04 -3.77E-05 1.46E-05 100 7.03E-05 -8.50E-05 4.59E-06 2.06E-05 1.22E-05 4.83E-06 4.39E-05 3.44E-05 -2.00E-05 -1.78E-04 -3.79E-05 1.41E-05 200 1.45E-04 -8.38E-05 7.16E-05 9.04E-05 5.82E-05 1.20E-04 1.50E-04 1.51E-04 1.23E-04 -2.35E-04 -3.78E-05 1.44E-05 -3.94E-05 4.38E-05 8.07E-05 -1.59E-04 -3.75E-05 3.77E-05 6.60E-05 -1.41E-04 -2.10E-05 4.54E-05 1.04E-04 -1.45E-04 4.54E-06 5.62E-05 1.59E-04 -1.50E-04 5.64E-05 8.51E-05 2.90E-04 -1.77E-04 -9.40E-05 -8.59E-05 -6.37E-05 -2.30E-05 6.17E-05 4.73E-05 4.88E-05 5.88E-05 9.02E-05 1.67E-04 3.57E-05 4.78E-05 9.76E-05 2.24E-04 5.19E-04 -2.24E-04 -2.20E-04 -2.25E-04 -2.70E-04 -3.95E-04 -4.50E-04 -6.00E-04 -7.50E-04 -9.00E-04 -9.00E-04 PASS PASS PASS PASS PASS 4.50E-04 6.00E-04 7.50E-04 9.00E-04 9.00E-04 PASS PASS PASS PASS PASS An ISO 9001:2008 and DSCC Certified Company 60 RLAT Report 10-055 100219 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Input Offset Voltage CH B @ VS=5V (V) 1.00E-03 8.00E-04 6.00E-04 4.00E-04 2.00E-04 0.00E+00 -2.00E-04 -4.00E-04 -6.00E-04 -8.00E-04 -1.00E-03 0 50 100 150 Total Dose (krad(Si)) Figure 5.28. Plot of input offset voltage at 5V for channel B versus total dose. The data show a slight increase with total dose, however not sufficient for the parameter to exceed specification, including after application of the KTL statistics. Note that this parameter is only specified to 100krad(Si) and the 200krad(Si) dose data is for reference only. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black line(s) show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray line(s) show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed line(s) are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 61 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 10-055 100219 R1.1 Table 5.28. Raw data for Input Offset Voltage CH B @ VS=5V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Input Offset Voltage CH B @ VS=5V (V) Device 41 116 182 241 325 408 492 724 786 868 929 1012 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status Total Dose (krad(Si)) 0 -2.70E-05 1.28E-05 -5.00E-05 1.28E-05 7.24E-06 -6.71E-05 1.24E-05 -7.26E-05 -9.54E-05 -4.47E-06 9.17E-06 -2.99E-05 20 -1.78E-05 2.96E-05 -3.53E-05 3.43E-05 2.25E-05 -5.67E-05 1.71E-05 -5.46E-05 -7.84E-05 7.60E-06 9.78E-06 -3.05E-05 50 7.48E-06 4.96E-05 -1.27E-05 6.25E-05 4.18E-05 -2.04E-05 3.83E-05 -1.63E-05 -4.61E-05 2.61E-05 9.90E-06 -3.01E-05 100 4.31E-05 7.26E-05 1.77E-05 1.03E-04 7.52E-05 3.53E-05 8.63E-05 4.70E-05 1.77E-05 6.53E-05 1.00E-05 -2.99E-05 200 1.12E-04 1.28E-04 8.33E-05 1.84E-04 1.36E-04 1.77E-04 1.81E-04 1.70E-04 1.55E-04 1.40E-04 1.10E-05 -2.97E-05 -8.84E-06 2.84E-05 6.89E-05 -8.66E-05 6.66E-06 3.12E-05 9.22E-05 -7.89E-05 2.97E-05 3.13E-05 1.15E-04 -5.60E-05 6.23E-05 3.28E-05 1.52E-04 -2.75E-05 1.29E-04 3.70E-05 2.30E-04 2.72E-05 -4.54E-05 -3.30E-05 -3.70E-06 5.03E-05 1.65E-04 4.67E-05 4.26E-05 3.49E-05 2.66E-05 1.70E-05 8.27E-05 8.37E-05 9.21E-05 1.23E-04 2.11E-04 -1.74E-04 -1.50E-04 -9.95E-05 -2.25E-05 1.18E-04 -4.50E-04 -6.00E-04 -7.50E-04 -9.00E-04 -9.00E-04 PASS PASS PASS PASS PASS 4.50E-04 6.00E-04 7.50E-04 9.00E-04 9.00E-04 PASS PASS PASS PASS PASS An ISO 9001:2008 and DSCC Certified Company 62 RLAT Report 10-055 100219 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Input Offset Current CH A @ VS=5V (V) 2.50E-08 2.00E-08 1.50E-08 1.00E-08 5.00E-09 0.00E+00 -5.00E-09 -1.00E-08 -1.50E-08 -2.00E-08 -2.50E-08 0 50 100 150 Total Dose (krad(Si)) Figure 5.29. Plot of Input Offset Current CH A @ VS=5V (V) versus total dose. The data show no significant change with total dose. Note that this parameter is only specified to 100krad(Si) and the 200krad(Si) dose data is for reference only. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 63 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 10-055 100219 R1.1 Table 5.29. Raw data for Input Offset Current CH A @ VS=5V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Input Offset Current CH A @ VS=5V (V) Device 41 116 182 241 325 408 492 724 786 868 929 1012 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status Total Dose (krad(Si)) 0 -1.63E-10 9.70E-11 8.90E-11 -5.10E-11 9.70E-11 -4.60E-11 -1.90E-11 1.08E-10 -9.00E-12 2.95E-10 -5.20E-11 0.00E+00 20 -1.84E-10 3.00E-12 3.70E-11 -4.60E-11 3.90E-11 -1.95E-10 -6.00E-12 9.30E-11 -1.40E-11 3.61E-10 -4.90E-11 -9.00E-12 50 -2.00E-12 1.87E-10 1.68E-10 -1.49E-10 -5.70E-11 -1.30E-10 -1.70E-11 -6.90E-11 0.00E+00 5.67E-10 -6.70E-11 7.00E-12 100 2.50E-11 5.09E-10 -2.66E-10 -4.28E-10 8.00E-12 -3.70E-11 -7.50E-11 1.90E-11 5.60E-11 8.57E-10 -5.00E-11 -8.00E-12 200 5.68E-10 8.28E-10 -3.94E-10 -3.33E-10 3.14E-10 2.86E-10 5.30E-10 2.23E-10 -3.00E-11 1.50E-09 -7.30E-11 -1.70E-11 1.38E-11 1.17E-10 3.35E-10 -3.08E-10 -3.02E-11 9.26E-11 2.24E-10 -2.84E-10 2.94E-11 1.45E-10 4.28E-10 -3.69E-10 -3.04E-11 3.57E-10 9.48E-10 -1.01E-09 1.97E-10 5.43E-10 1.69E-09 -1.29E-09 6.58E-11 4.78E-11 7.02E-11 1.64E-10 5.02E-10 1.41E-10 2.04E-10 2.82E-10 3.91E-10 5.93E-10 4.53E-10 6.06E-10 8.44E-10 1.24E-09 2.13E-09 -3.21E-10 -5.10E-10 -7.04E-10 -9.07E-10 -1.12E-09 -1.00E-08 -1.00E-08 -1.50E-08 -2.00E-08 -2.00E-08 PASS PASS PASS PASS PASS 1.00E-08 1.00E-08 1.50E-08 2.00E-08 2.00E-08 PASS PASS PASS PASS PASS An ISO 9001:2008 and DSCC Certified Company 64 RLAT Report 10-055 100219 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Input Offset Current CH B @ VS=5V (A) 2.50E-08 2.00E-08 1.50E-08 1.00E-08 5.00E-09 0.00E+00 -5.00E-09 -1.00E-08 -1.50E-08 -2.00E-08 -2.50E-08 0 50 100 150 Total Dose (krad(Si)) Figure 5.30. Plot of Input Offset Current CH B @ VS=5V (A) versus total dose. The data show no significant change with total dose. Note that this parameter is only specified to 100krad(Si) and the 200krad(Si) dose data is for reference only. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 65 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 10-055 100219 R1.1 Table 5.30. Raw data for Input Offset Current CH B @ VS=5V (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Input Offset Current CH B @ VS=5V (A) Device 41 116 182 241 325 408 492 724 786 868 929 1012 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status Total Dose (krad(Si)) 0 -1.20E-10 3.00E-12 8.00E-12 -7.30E-11 -2.00E-12 -1.58E-10 -7.00E-12 8.20E-11 -4.60E-11 -2.16E-10 -7.80E-11 -1.17E-10 20 -1.98E-10 -1.60E-11 -5.90E-11 7.00E-12 -2.50E-11 -2.17E-10 -4.70E-11 -3.80E-11 -1.79E-10 -1.98E-10 -1.07E-10 -1.64E-10 50 -2.40E-10 -1.47E-10 -1.58E-10 -1.69E-10 1.30E-10 -2.67E-10 -1.91E-10 -1.30E-10 -4.59E-10 -2.68E-10 -9.00E-11 -1.27E-10 100 -9.00E-11 -3.30E-11 8.00E-12 -1.80E-10 7.10E-11 -2.48E-10 -3.48E-10 -3.98E-10 -6.19E-10 -2.16E-10 -7.30E-11 -1.17E-10 200 5.30E-10 2.90E-10 3.10E-11 3.26E-10 6.34E-10 -1.04E-10 4.05E-10 -1.33E-10 -6.15E-10 1.98E-10 -8.20E-11 -1.15E-10 -3.68E-11 5.71E-11 1.20E-10 -1.93E-10 -5.82E-11 8.17E-11 1.66E-10 -2.82E-10 -1.17E-10 1.43E-10 2.74E-10 -5.08E-10 -4.48E-11 9.57E-11 2.18E-10 -3.07E-10 3.62E-10 2.34E-10 1.00E-09 -2.78E-10 -6.90E-11 -1.36E-10 -2.63E-10 -3.66E-10 -4.98E-11 1.19E-10 8.63E-11 1.24E-10 1.60E-10 3.87E-10 2.57E-10 1.01E-10 7.65E-11 7.16E-11 1.01E-09 -3.95E-10 -3.72E-10 -6.03E-10 -8.03E-10 -1.11E-09 -1.00E-08 -1.00E-08 -1.50E-08 -2.00E-08 -2.00E-08 PASS PASS PASS PASS PASS 1.00E-08 1.00E-08 1.50E-08 2.00E-08 2.00E-08 PASS PASS PASS PASS PASS An ISO 9001:2008 and DSCC Certified Company 66 RLAT Report 10-055 100219 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX + Input Bias Current CH A @ VS=5V (A) 2.50E-07 2.00E-07 1.50E-07 1.00E-07 5.00E-08 0.00E+00 -5.00E-08 -1.00E-07 -1.50E-07 -2.00E-07 -2.50E-07 0 50 100 150 Total Dose (krad(Si)) Figure 5.31. Plot of input bias current, non-inverting input at 5V for channel A versus total dose. The data show an increase with total dose, however not sufficient for the parameter to exceed specification, including after application of the KTL statistics. Note that this parameter is only specified to 100krad(Si) and the 200krad(Si) dose data is for reference only. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black line(s) show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray line(s) show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed line(s) are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 67 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 10-055 100219 R1.1 Table 5.31. Raw data for + Input Bias Current CH A @ VS=5V (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). + Input Bias Current CH A @ VS=5V (A) Device 41 116 182 241 325 408 492 724 786 868 929 1012 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status Total Dose (krad(Si)) 0 1.21E-08 1.29E-08 1.31E-08 1.35E-08 1.25E-08 1.25E-08 1.17E-08 1.28E-08 1.35E-08 1.19E-08 1.28E-08 1.23E-08 20 1.57E-08 1.62E-08 1.68E-08 1.76E-08 1.60E-08 1.63E-08 1.53E-08 1.66E-08 1.76E-08 1.57E-08 1.28E-08 1.24E-08 50 2.34E-08 2.33E-08 2.45E-08 2.60E-08 2.29E-08 2.35E-08 2.21E-08 2.39E-08 2.51E-08 2.28E-08 1.28E-08 1.24E-08 100 3.57E-08 3.55E-08 3.75E-08 3.92E-08 3.47E-08 3.52E-08 3.33E-08 3.59E-08 3.71E-08 3.46E-08 1.29E-08 1.24E-08 200 5.64E-08 5.80E-08 5.97E-08 6.27E-08 5.46E-08 5.53E-08 5.29E-08 5.63E-08 5.86E-08 5.50E-08 1.28E-08 1.24E-08 1.28E-08 5.57E-10 1.44E-08 1.13E-08 1.65E-08 7.47E-10 1.85E-08 1.44E-08 2.40E-08 1.26E-09 2.75E-08 2.06E-08 3.65E-08 1.82E-09 4.15E-08 3.15E-08 5.83E-08 3.13E-09 6.69E-08 4.97E-08 1.25E-08 1.63E-08 2.35E-08 3.52E-08 5.56E-08 6.97E-10 8.86E-10 1.14E-09 1.44E-09 2.08E-09 1.44E-08 1.87E-08 2.66E-08 3.92E-08 6.13E-08 1.06E-08 1.39E-08 2.03E-08 3.13E-08 4.99E-08 -5.00E-08 -1.00E-07 -1.25E-07 -2.00E-07 -2.00E-07 PASS PASS PASS PASS PASS 5.00E-08 1.00E-07 1.25E-07 2.00E-07 2.00E-07 PASS PASS PASS PASS PASS An ISO 9001:2008 and DSCC Certified Company 68 RLAT Report 10-055 100219 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX + Input Bias Current CH B @ VS=5V (A) 2.50E-07 2.00E-07 1.50E-07 1.00E-07 5.00E-08 0.00E+00 -5.00E-08 -1.00E-07 -1.50E-07 -2.00E-07 -2.50E-07 0 50 100 150 Total Dose (krad(Si)) Figure 5.32. Plot of input bias current, non-inverting input at 5V for channel B versus total dose. The data show a slight increase with total dose, however not sufficient for the parameter to exceed specification, including after application of the KTL statistics. Note that this parameter is only specified to 100krad(Si) and the 200krad(Si) dose data is for reference only. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the un-biased sample. The black line(s) show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray line(s) show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed line(s) are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 69 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 10-055 100219 R1.1 Table 5.32. Raw data for + Input Bias Current CH B @ VS=5V (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). + Input Bias Current CH B @ VS=5V (A) Device 41 116 182 241 325 408 492 724 786 868 929 1012 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status Total Dose (krad(Si)) 0 1.25E-08 1.34E-08 1.36E-08 1.43E-08 1.29E-08 1.37E-08 1.21E-08 1.40E-08 1.33E-08 1.30E-08 1.32E-08 1.27E-08 20 1.65E-08 1.68E-08 1.75E-08 1.85E-08 1.66E-08 1.78E-08 1.59E-08 1.81E-08 1.75E-08 1.71E-08 1.32E-08 1.28E-08 50 2.45E-08 2.43E-08 2.56E-08 2.74E-08 2.37E-08 2.56E-08 2.31E-08 2.61E-08 2.52E-08 2.46E-08 1.32E-08 1.28E-08 100 3.69E-08 3.68E-08 3.87E-08 4.11E-08 3.58E-08 3.82E-08 3.50E-08 3.90E-08 3.73E-08 3.71E-08 1.32E-08 1.28E-08 200 5.82E-08 5.97E-08 6.17E-08 6.55E-08 5.60E-08 5.97E-08 5.54E-08 6.10E-08 5.87E-08 5.85E-08 1.32E-08 1.28E-08 1.34E-08 6.84E-10 1.52E-08 1.15E-08 1.72E-08 8.50E-10 1.95E-08 1.48E-08 2.51E-08 1.47E-09 2.91E-08 2.11E-08 3.79E-08 2.08E-09 4.36E-08 3.22E-08 6.02E-08 3.63E-09 7.02E-08 5.03E-08 1.32E-08 1.73E-08 2.49E-08 3.73E-08 5.87E-08 7.06E-10 8.70E-10 1.13E-09 1.53E-09 2.07E-09 1.51E-08 1.97E-08 2.80E-08 4.15E-08 6.44E-08 1.13E-08 1.49E-08 2.18E-08 3.31E-08 5.30E-08 -5.00E-08 -1.00E-07 -1.25E-07 -2.00E-07 -2.00E-07 PASS PASS PASS PASS PASS 5.00E-08 1.00E-07 1.25E-07 2.00E-07 2.00E-07 PASS PASS PASS PASS PASS An ISO 9001:2008 and DSCC Certified Company 70 RLAT Report 10-055 100219 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX - Input Bias Current CH A @ VS=5V (A) 2.50E-07 2.00E-07 1.50E-07 1.00E-07 5.00E-08 0.00E+00 -5.00E-08 -1.00E-07 -1.50E-07 -2.00E-07 -2.50E-07 0 50 100 150 Total Dose (krad(Si)) Figure 5.33. Plot of input bias current, inverting input at 5V for channel A versus total dose. The data show a slight increase with total dose, however not sufficient for the parameter to exceed specification, including after application of the KTL statistics. Note that this parameter is only specified to 100krad(Si) and the 200krad(Si) dose data is for reference only. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the unbiased sample. The black line(s) show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray line(s) show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed line(s) are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 71 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 10-055 100219 R1.1 Table 5.33. Raw data for - Input Bias Current CH A @ VS=5V (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). - Input Bias Current CH A @ VS=5V (A) Device 41 116 182 241 325 408 492 724 786 868 929 1012 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status Total Dose (krad(Si)) 0 1.19E-08 1.30E-08 1.31E-08 1.35E-08 1.26E-08 1.25E-08 1.18E-08 1.29E-08 1.35E-08 1.22E-08 1.27E-08 1.23E-08 20 1.56E-08 1.63E-08 1.69E-08 1.76E-08 1.60E-08 1.61E-08 1.52E-08 1.67E-08 1.76E-08 1.60E-08 1.28E-08 1.23E-08 50 2.34E-08 2.35E-08 2.47E-08 2.59E-08 2.30E-08 2.34E-08 2.20E-08 2.40E-08 2.52E-08 2.34E-08 1.28E-08 1.24E-08 100 3.57E-08 3.60E-08 3.73E-08 3.88E-08 3.49E-08 3.53E-08 3.33E-08 3.59E-08 3.73E-08 3.55E-08 1.27E-08 1.23E-08 200 5.71E-08 5.89E-08 5.93E-08 6.25E-08 5.49E-08 5.56E-08 5.35E-08 5.66E-08 5.86E-08 5.65E-08 1.28E-08 1.23E-08 1.28E-08 6.11E-10 1.45E-08 1.11E-08 1.65E-08 7.77E-10 1.86E-08 1.43E-08 2.41E-08 1.20E-09 2.74E-08 2.08E-08 3.65E-08 1.55E-09 4.08E-08 3.23E-08 5.85E-08 2.83E-09 6.63E-08 5.08E-08 1.26E-08 1.63E-08 2.36E-08 3.55E-08 5.62E-08 6.70E-10 8.78E-10 1.13E-09 1.46E-09 1.86E-09 1.44E-08 1.87E-08 2.67E-08 3.94E-08 6.12E-08 1.07E-08 1.39E-08 2.05E-08 3.15E-08 5.11E-08 -5.00E-08 -1.00E-07 -1.25E-07 -2.00E-07 -2.00E-07 PASS PASS PASS PASS PASS 5.00E-08 1.00E-07 1.25E-07 2.00E-07 2.00E-07 PASS PASS PASS PASS PASS An ISO 9001:2008 and DSCC Certified Company 72 RLAT Report 10-055 100219 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX - Input Bias Current CH B @ VS=5V (A) 2.50E-07 2.00E-07 1.50E-07 1.00E-07 5.00E-08 0.00E+00 -5.00E-08 -1.00E-07 -1.50E-07 -2.00E-07 -2.50E-07 0 50 100 150 Total Dose (krad(Si)) Figure 5.34. Plot of input bias current, inverting input at 5V for channel B versus total dose. The data show a slight increase with total dose, however not sufficient for the parameter to exceed specification, including after application of the KTL statistics. Note that this parameter is only specified to 100krad(Si) and the 200krad(Si) dose data is for reference only. The solid diamonds are the average of measured data points from the biased sample (devices irradiated with an electrical bias) while the shaded diamonds are the average from the unbiased sample. The black line(s) show the effects on the data after application of the biased KTL statistics (solid and/or dashed lines) while the gray line(s) show the effects on the data after application of the unbiased KTL statistics (solid and/or dashed lines). The red dashed line(s) are the minimum and/or maximum specification values as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 73 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 10-055 100219 R1.1 Table 5.34. Raw data for - Input Bias Current CH B @ VS=5V (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). - Input Bias Current CH B @ VS=5V (A) Device 41 116 182 241 325 408 492 724 786 868 929 1012 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Specification MAX Status Total Dose (krad(Si)) 0 1.24E-08 1.34E-08 1.36E-08 1.42E-08 1.30E-08 1.35E-08 1.22E-08 1.40E-08 1.33E-08 1.28E-08 1.31E-08 1.26E-08 20 1.63E-08 1.68E-08 1.74E-08 1.86E-08 1.66E-08 1.76E-08 1.59E-08 1.81E-08 1.73E-08 1.68E-08 1.32E-08 1.27E-08 50 2.42E-08 2.41E-08 2.55E-08 2.72E-08 2.38E-08 2.54E-08 2.30E-08 2.60E-08 2.48E-08 2.44E-08 1.32E-08 1.27E-08 100 3.69E-08 3.68E-08 3.89E-08 4.10E-08 3.59E-08 3.80E-08 3.46E-08 3.87E-08 3.67E-08 3.70E-08 1.32E-08 1.27E-08 200 5.88E-08 6.01E-08 6.19E-08 6.59E-08 5.66E-08 5.97E-08 5.58E-08 6.10E-08 5.82E-08 5.89E-08 1.31E-08 1.27E-08 1.33E-08 7.04E-10 1.53E-08 1.14E-08 1.71E-08 9.16E-10 1.97E-08 1.46E-08 2.50E-08 1.41E-09 2.88E-08 2.11E-08 3.79E-08 2.05E-09 4.35E-08 3.23E-08 6.07E-08 3.50E-09 7.03E-08 5.11E-08 1.32E-08 1.72E-08 2.47E-08 3.70E-08 5.87E-08 6.94E-10 8.41E-10 1.12E-09 1.55E-09 1.93E-09 1.51E-08 1.95E-08 2.78E-08 4.13E-08 6.40E-08 1.13E-08 1.49E-08 2.16E-08 3.28E-08 5.34E-08 -5.00E-08 -1.00E-07 -1.25E-07 -2.00E-07 -2.00E-07 PASS PASS PASS PASS PASS 5.00E-08 1.00E-07 1.25E-07 2.00E-07 2.00E-07 PASS PASS PASS PASS PASS An ISO 9001:2008 and DSCC Certified Company 74 Output Voltage High, No Load CH A @ VS=5V (V) RLAT Report 10-055 100219 R1.1 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (-KTL) Biased 4.35E+00 4.30E+00 4.25E+00 4.20E+00 4.15E+00 4.10E+00 4.05E+00 4.00E+00 3.95E+00 0 50 100 150 Total Dose (krad(Si)) Figure 5.35. Plot of Output Voltage High, No Load CH A @ VS=5V (V) versus total dose. The data show no significant change with total dose. Note that this parameter is only specified to 100krad(Si) and the 200krad(Si) dose data is for reference only. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or postirradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 75 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 10-055 100219 R1.1 Table 5.35. Raw data for Output Voltage High, No Load CH A @ VS=5V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage High, No Load CH A @ VS=5V (V) Device 41 116 182 241 325 408 492 724 786 868 929 1012 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Total Dose (krad(Si)) 0 4.28E+00 4.29E+00 4.27E+00 4.27E+00 4.28E+00 4.28E+00 4.28E+00 4.28E+00 4.27E+00 4.29E+00 4.28E+00 4.28E+00 20 4.28E+00 4.30E+00 4.28E+00 4.28E+00 4.29E+00 4.28E+00 4.28E+00 4.28E+00 4.27E+00 4.29E+00 4.28E+00 4.28E+00 50 4.29E+00 4.30E+00 4.28E+00 4.28E+00 4.29E+00 4.29E+00 4.29E+00 4.29E+00 4.28E+00 4.30E+00 4.28E+00 4.28E+00 100 4.33E+00 4.33E+00 4.32E+00 4.31E+00 4.32E+00 4.31E+00 4.31E+00 4.32E+00 4.31E+00 4.32E+00 4.28E+00 4.28E+00 200 4.33E+00 4.34E+00 4.33E+00 4.33E+00 4.33E+00 4.33E+00 4.33E+00 4.32E+00 4.33E+00 4.34E+00 4.28E+00 4.28E+00 4.28E+00 7.21E-03 4.30E+00 4.26E+00 4.28E+00 7.54E-03 4.30E+00 4.26E+00 4.29E+00 5.94E-03 4.30E+00 4.27E+00 4.32E+00 7.99E-03 4.34E+00 4.30E+00 4.33E+00 4.22E-03 4.34E+00 4.32E+00 4.28E+00 4.28E+00 4.29E+00 4.32E+00 4.33E+00 6.77E-03 6.50E-03 5.36E-03 4.51E-03 6.87E-03 4.30E+00 4.30E+00 4.30E+00 4.33E+00 4.35E+00 4.26E+00 4.26E+00 4.27E+00 4.30E+00 4.31E+00 4.00E+00 4.00E+00 4.00E+00 4.00E+00 4.00E+00 PASS PASS PASS PASS PASS An ISO 9001:2008 and DSCC Certified Company 76 Output Voltage High, No Load CH B @ VS=5V (V) RLAT Report 10-055 100219 R1.1 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (-KTL) Biased 4.35E+00 4.30E+00 4.25E+00 4.20E+00 4.15E+00 4.10E+00 4.05E+00 4.00E+00 3.95E+00 0 50 100 150 Total Dose (krad(Si)) Figure 5.36. Plot of Output Voltage High, No Load CH B @ VS=5V (V) versus total dose. The data show no significant change with total dose. Note that this parameter is only specified to 100krad(Si) and the 200krad(Si) dose data is for reference only. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or postirradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 77 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 10-055 100219 R1.1 Table 5.36. Raw data for Output Voltage High, No Load CH B @ VS=5V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage High, No Load CH B @ VS=5V (V) Device 41 116 182 241 325 408 492 724 786 868 929 1012 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Total Dose (krad(Si)) 0 4.27E+00 4.27E+00 4.26E+00 4.26E+00 4.27E+00 4.27E+00 4.27E+00 4.26E+00 4.26E+00 4.26E+00 4.27E+00 4.27E+00 20 4.27E+00 4.28E+00 4.27E+00 4.26E+00 4.27E+00 4.27E+00 4.27E+00 4.27E+00 4.26E+00 4.26E+00 4.27E+00 4.27E+00 50 4.28E+00 4.28E+00 4.27E+00 4.27E+00 4.28E+00 4.27E+00 4.27E+00 4.27E+00 4.27E+00 4.26E+00 4.27E+00 4.27E+00 100 4.30E+00 4.30E+00 4.29E+00 4.29E+00 4.30E+00 4.30E+00 4.29E+00 4.30E+00 4.29E+00 4.28E+00 4.27E+00 4.27E+00 200 4.33E+00 4.34E+00 4.33E+00 4.33E+00 4.33E+00 4.33E+00 4.33E+00 4.33E+00 4.33E+00 4.34E+00 4.27E+00 4.27E+00 4.27E+00 5.72E-03 4.28E+00 4.25E+00 4.27E+00 5.68E-03 4.29E+00 4.26E+00 4.27E+00 4.60E-03 4.29E+00 4.26E+00 4.30E+00 4.67E-03 4.31E+00 4.28E+00 4.33E+00 4.62E-03 4.34E+00 4.32E+00 4.26E+00 4.26E+00 4.27E+00 4.29E+00 4.33E+00 3.44E-03 3.11E-03 4.32E-03 8.17E-03 3.78E-03 4.27E+00 4.27E+00 4.28E+00 4.31E+00 4.34E+00 4.25E+00 4.26E+00 4.26E+00 4.27E+00 4.32E+00 4.00E+00 4.00E+00 4.00E+00 4.00E+00 4.00E+00 PASS PASS PASS PASS PASS An ISO 9001:2008 and DSCC Certified Company 78 Output Voltage High, 600Ω CH A @ VS=5V (V) RLAT Report 10-055 100219 R1.1 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (-KTL) Biased 4.00E+00 3.80E+00 3.60E+00 3.40E+00 3.20E+00 3.00E+00 2.80E+00 2.60E+00 2.40E+00 2.20E+00 2.00E+00 0 50 100 150 Total Dose (krad(Si)) Figure 5.37. Plot of Output Voltage High, 600Ω CH A @ VS=5V (V) versus total dose. The data show no significant change with total dose. Note that this parameter is only specified to 100krad(Si) and the 200krad(Si) dose data is for reference only. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or postirradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 79 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 10-055 100219 R1.1 Table 5.37. Raw data for Output Voltage High, 600Ω CH A @ VS=5V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage High, 600Ω CH A @ VS=5V (V) Device 41 116 182 241 325 408 492 724 786 868 929 1012 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Total Dose (krad(Si)) 0 3.84E+00 3.86E+00 3.84E+00 3.84E+00 3.84E+00 3.83E+00 3.84E+00 3.83E+00 3.82E+00 3.87E+00 3.84E+00 3.84E+00 20 3.84E+00 3.86E+00 3.84E+00 3.84E+00 3.84E+00 3.83E+00 3.84E+00 3.83E+00 3.82E+00 3.87E+00 3.84E+00 3.85E+00 50 3.83E+00 3.86E+00 3.84E+00 3.84E+00 3.84E+00 3.83E+00 3.83E+00 3.82E+00 3.82E+00 3.87E+00 3.84E+00 3.85E+00 100 3.83E+00 3.85E+00 3.83E+00 3.84E+00 3.84E+00 3.83E+00 3.83E+00 3.82E+00 3.82E+00 3.87E+00 3.84E+00 3.85E+00 200 3.83E+00 3.85E+00 3.83E+00 3.83E+00 3.83E+00 3.82E+00 3.82E+00 3.81E+00 3.81E+00 3.87E+00 3.84E+00 3.85E+00 3.84E+00 8.58E-03 3.87E+00 3.82E+00 3.84E+00 8.80E-03 3.87E+00 3.82E+00 3.84E+00 9.13E-03 3.87E+00 3.82E+00 3.84E+00 9.52E-03 3.86E+00 3.81E+00 3.83E+00 9.71E-03 3.86E+00 3.81E+00 3.84E+00 3.84E+00 3.84E+00 3.83E+00 3.83E+00 2.01E-02 2.08E-02 2.16E-02 2.15E-02 2.34E-02 3.89E+00 3.89E+00 3.89E+00 3.89E+00 3.89E+00 3.78E+00 3.78E+00 3.78E+00 3.77E+00 3.76E+00 3.40E+00 3.20E+00 3.00E+00 2.80E+00 2.80E+00 PASS PASS PASS PASS PASS An ISO 9001:2008 and DSCC Certified Company 80 Output Voltage High, 600Ω CH B @ VS=5V (V) RLAT Report 10-055 100219 R1.1 Average Biased Average Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (-KTL) Biased 4.00E+00 3.80E+00 3.60E+00 3.40E+00 3.20E+00 3.00E+00 2.80E+00 2.60E+00 2.40E+00 2.20E+00 2.00E+00 0 50 100 150 Total Dose (krad(Si)) Figure 5.38. Plot of Output Voltage High, 600Ω CH B @ VS=5V (V) versus total dose. The data show no significant change with total dose. Note that this parameter is only specified to 100krad(Si) and the 200krad(Si) dose data is for reference only. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or postirradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 81 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 10-055 100219 R1.1 Table 5.38. Raw data for Output Voltage High, 600Ω CH B @ VS=5V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage High, 600Ω CH B @ VS=5V (V) Device 41 116 182 241 325 408 492 724 786 868 929 1012 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Status Total Dose (krad(Si)) 0 3.84E+00 3.86E+00 3.85E+00 3.85E+00 3.85E+00 3.84E+00 3.84E+00 3.83E+00 3.83E+00 3.88E+00 3.85E+00 3.85E+00 20 3.84E+00 3.87E+00 3.85E+00 3.85E+00 3.85E+00 3.84E+00 3.84E+00 3.83E+00 3.83E+00 3.88E+00 3.85E+00 3.85E+00 50 3.84E+00 3.86E+00 3.85E+00 3.85E+00 3.85E+00 3.84E+00 3.84E+00 3.83E+00 3.83E+00 3.88E+00 3.85E+00 3.85E+00 100 3.84E+00 3.86E+00 3.84E+00 3.84E+00 3.85E+00 3.83E+00 3.84E+00 3.83E+00 3.82E+00 3.88E+00 3.85E+00 3.85E+00 200 3.83E+00 3.86E+00 3.84E+00 3.84E+00 3.84E+00 3.83E+00 3.83E+00 3.82E+00 3.82E+00 3.87E+00 3.85E+00 3.85E+00 3.85E+00 8.38E-03 3.87E+00 3.83E+00 3.85E+00 9.10E-03 3.88E+00 3.83E+00 3.85E+00 9.03E-03 3.87E+00 3.82E+00 3.85E+00 9.86E-03 3.87E+00 3.82E+00 3.84E+00 1.01E-02 3.87E+00 3.81E+00 3.84E+00 3.85E+00 3.84E+00 3.84E+00 3.83E+00 1.91E-02 1.98E-02 2.02E-02 2.06E-02 2.23E-02 3.90E+00 3.90E+00 3.90E+00 3.90E+00 3.89E+00 3.79E+00 3.79E+00 3.79E+00 3.78E+00 3.77E+00 3.40E+00 3.20E+00 3.00E+00 2.80E+00 2.80E+00 PASS PASS PASS PASS PASS An ISO 9001:2008 and DSCC Certified Company 82 Output Voltage Low, No Load CH A @ VS=5V (V) RLAT Report 10-055 100219 R1.1 Average Biased Average Un-Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (+KTL) Biased 6.00E-02 5.00E-02 4.00E-02 3.00E-02 2.00E-02 1.00E-02 0.00E+00 0 50 100 150 Total Dose (krad(Si)) Figure 5.39. Plot of Output Voltage Low, No Load CH A @ VS=5V (V) versus total dose. The data show no significant change with total dose. Note that this parameter is only specified to 100krad(Si) and the 200krad(Si) dose data is for reference only. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or postirradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 83 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 10-055 100219 R1.1 Table 5.39. Raw data for Output Voltage Low, No Load CH A @ VS=5V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Low, No Load CH A @ VS=5V (V) Device 41 116 182 241 325 408 492 724 786 868 929 1012 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MAX Status Total Dose (krad(Si)) 0 1.37E-02 1.41E-02 1.35E-02 1.37E-02 1.39E-02 1.36E-02 1.36E-02 1.36E-02 1.35E-02 1.41E-02 1.37E-02 1.38E-02 20 1.39E-02 1.41E-02 1.39E-02 1.38E-02 1.40E-02 1.37E-02 1.40E-02 1.37E-02 1.39E-02 1.42E-02 1.37E-02 1.38E-02 50 1.41E-02 1.42E-02 1.38E-02 1.41E-02 1.41E-02 1.40E-02 1.41E-02 1.38E-02 1.40E-02 1.43E-02 1.36E-02 1.38E-02 100 1.42E-02 1.44E-02 1.41E-02 1.40E-02 1.42E-02 1.41E-02 1.43E-02 1.43E-02 1.43E-02 1.45E-02 1.37E-02 1.39E-02 200 1.45E-02 1.47E-02 1.44E-02 1.46E-02 1.45E-02 1.49E-02 1.49E-02 1.51E-02 1.50E-02 1.49E-02 1.38E-02 1.39E-02 1.38E-02 2.28E-04 1.44E-02 1.32E-02 1.39E-02 1.14E-04 1.43E-02 1.36E-02 1.41E-02 1.52E-04 1.45E-02 1.36E-02 1.42E-02 1.48E-04 1.46E-02 1.38E-02 1.45E-02 1.14E-04 1.49E-02 1.42E-02 1.37E-02 1.39E-02 1.40E-02 1.43E-02 1.50E-02 2.39E-04 2.12E-04 1.82E-04 1.41E-04 8.94E-05 1.43E-02 1.45E-02 1.45E-02 1.47E-02 1.52E-02 1.30E-02 1.33E-02 1.35E-02 1.39E-02 1.47E-02 2.50E-02 3.00E-02 4.00E-02 5.00E-02 5.00E-02 PASS PASS PASS PASS PASS An ISO 9001:2008 and DSCC Certified Company 84 Output Voltage Low, No Load CH B @ VS=5V (V) RLAT Report 10-055 100219 R1.1 Average Biased Average Un-Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (+KTL) Biased 6.00E-02 5.00E-02 4.00E-02 3.00E-02 2.00E-02 1.00E-02 0.00E+00 0 50 100 150 Total Dose (krad(Si)) Figure 5.40. Plot of Output Voltage Low, No Load CH B @ VS=5V (V) versus total dose. The data show no significant change with total dose. Note that this parameter is only specified to 100krad(Si) and the 200krad(Si) dose data is for reference only. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or postirradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 85 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 10-055 100219 R1.1 Table 5.40. Raw data for Output Voltage Low, No Load CH B @ VS=5V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Low, No Load CH B @ VS=5V (V) Device 41 116 182 241 325 408 492 724 786 868 929 1012 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MAX Status Total Dose (krad(Si)) 0 1.37E-02 1.40E-02 1.36E-02 1.36E-02 1.38E-02 1.37E-02 1.37E-02 1.35E-02 1.35E-02 1.40E-02 1.35E-02 1.35E-02 20 1.37E-02 1.42E-02 1.38E-02 1.38E-02 1.39E-02 1.38E-02 1.39E-02 1.37E-02 1.35E-02 1.42E-02 1.37E-02 1.37E-02 50 1.40E-02 1.43E-02 1.40E-02 1.40E-02 1.40E-02 1.38E-02 1.40E-02 1.38E-02 1.37E-02 1.42E-02 1.36E-02 1.38E-02 100 1.41E-02 1.43E-02 1.40E-02 1.41E-02 1.41E-02 1.41E-02 1.42E-02 1.43E-02 1.42E-02 1.44E-02 1.35E-02 1.37E-02 200 1.43E-02 1.45E-02 1.43E-02 1.44E-02 1.42E-02 1.50E-02 1.49E-02 1.48E-02 1.49E-02 1.49E-02 1.36E-02 1.35E-02 1.37E-02 1.67E-04 1.42E-02 1.33E-02 1.39E-02 1.92E-04 1.44E-02 1.34E-02 1.41E-02 1.34E-04 1.44E-02 1.37E-02 1.41E-02 1.10E-04 1.44E-02 1.38E-02 1.43E-02 1.14E-04 1.47E-02 1.40E-02 1.37E-02 1.38E-02 1.39E-02 1.42E-02 1.49E-02 2.05E-04 2.59E-04 2.00E-04 1.14E-04 7.07E-05 1.42E-02 1.45E-02 1.44E-02 1.46E-02 1.51E-02 1.31E-02 1.31E-02 1.34E-02 1.39E-02 1.47E-02 2.50E-02 3.00E-02 4.00E-02 5.00E-02 5.00E-02 PASS PASS PASS PASS PASS An ISO 9001:2008 and DSCC Certified Company 86 RLAT Report 10-055 100219 R1.1 Average Biased Average Un-Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (+KTL) Biased Output Voltage Low, 600Ω CH A @ VS=5V (V) 1.20E-02 1.00E-02 8.00E-03 6.00E-03 4.00E-03 2.00E-03 0.00E+00 0 50 100 150 Total Dose (krad(Si)) Figure 5.41. Plot of Output Voltage Low, 600Ω CH A @ VS=5V (V) versus total dose. The data show no significant change with total dose. Note that this parameter is only specified to 100krad(Si) and the 200krad(Si) dose data is for reference only. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or postirradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 87 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 10-055 100219 R1.1 Table 5.41. Raw data for Output Voltage Low, 600Ω CH A @ VS=5V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Low, 600Ω CH A @ VS=5V (V) Device 41 116 182 241 325 408 492 724 786 868 929 1012 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MAX Status Total Dose (krad(Si)) 0 1.80E-03 1.80E-03 2.00E-03 1.90E-03 1.70E-03 1.70E-03 1.70E-03 1.70E-03 1.60E-03 2.10E-03 1.90E-03 1.90E-03 20 1.80E-03 1.80E-03 1.90E-03 2.00E-03 1.70E-03 1.60E-03 1.90E-03 1.80E-03 1.60E-03 2.20E-03 1.90E-03 1.90E-03 50 1.50E-03 1.90E-03 1.80E-03 1.80E-03 1.40E-03 1.50E-03 1.70E-03 1.60E-03 1.30E-03 2.00E-03 1.90E-03 1.90E-03 100 1.20E-03 1.40E-03 1.40E-03 1.40E-03 1.20E-03 1.10E-03 1.40E-03 1.20E-03 1.20E-03 1.80E-03 1.90E-03 2.10E-03 200 5.00E-04 7.00E-04 8.00E-04 8.00E-04 5.00E-04 6.00E-04 7.00E-04 6.00E-04 4.00E-04 1.00E-03 1.80E-03 2.00E-03 1.84E-03 1.14E-04 2.15E-03 1.53E-03 1.84E-03 1.14E-04 2.15E-03 1.53E-03 1.68E-03 2.17E-04 2.27E-03 1.09E-03 1.32E-03 1.10E-04 1.62E-03 1.02E-03 6.60E-04 1.52E-04 1.08E-03 2.44E-04 1.76E-03 1.82E-03 1.62E-03 1.34E-03 6.60E-04 1.95E-04 2.49E-04 2.59E-04 2.79E-04 2.19E-04 2.29E-03 2.50E-03 2.33E-03 2.11E-03 1.26E-03 1.23E-03 1.14E-03 9.10E-04 5.74E-04 5.93E-05 1.00E-02 1.00E-02 1.00E-02 1.00E-02 1.00E-02 PASS PASS PASS PASS PASS An ISO 9001:2008 and DSCC Certified Company 88 RLAT Report 10-055 100219 R1.1 Average Biased Average Un-Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (+KTL) Biased Output Voltage Low, 600Ω CH B @ VS=5V (V) 1.20E-02 1.00E-02 8.00E-03 6.00E-03 4.00E-03 2.00E-03 0.00E+00 0 50 100 150 Total Dose (krad(Si)) Figure 5.42. Plot of Output Voltage Low, 600Ω CH B @ VS=5V (V) versus total dose. The data show no significant change with total dose. Note that this parameter is only specified to 100krad(Si) and the 200krad(Si) dose data is for reference only. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or postirradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 89 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 10-055 100219 R1.1 Table 5.42. Raw data for Output Voltage Low, 600Ω CH B @ VS=5V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Low, 600Ω CH B @ VS=5V (V) Device 41 116 182 241 325 408 492 724 786 868 929 1012 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MAX Status Total Dose (krad(Si)) 0 2.20E-03 2.20E-03 2.30E-03 2.40E-03 2.10E-03 1.90E-03 2.10E-03 2.00E-03 2.00E-03 2.60E-03 2.20E-03 2.30E-03 20 2.00E-03 2.20E-03 2.20E-03 2.40E-03 2.00E-03 1.90E-03 2.20E-03 2.10E-03 1.90E-03 2.60E-03 2.30E-03 2.30E-03 50 1.90E-03 2.00E-03 2.00E-03 2.10E-03 1.90E-03 1.70E-03 2.00E-03 1.90E-03 1.80E-03 2.40E-03 2.10E-03 2.20E-03 100 1.30E-03 1.60E-03 1.80E-03 1.90E-03 1.70E-03 1.40E-03 1.70E-03 1.70E-03 1.50E-03 2.10E-03 2.30E-03 2.40E-03 200 8.00E-04 1.20E-03 1.20E-03 1.20E-03 8.00E-04 8.00E-04 8.00E-04 9.00E-04 8.00E-04 1.50E-03 2.30E-03 2.30E-03 2.24E-03 1.14E-04 2.55E-03 1.93E-03 2.16E-03 1.67E-04 2.62E-03 1.70E-03 1.98E-03 8.37E-05 2.21E-03 1.75E-03 1.66E-03 2.30E-04 2.29E-03 1.03E-03 1.04E-03 2.19E-04 1.64E-03 4.39E-04 2.12E-03 2.14E-03 1.96E-03 1.68E-03 9.60E-04 2.77E-04 2.88E-04 2.70E-04 2.68E-04 3.05E-04 2.88E-03 2.93E-03 2.70E-03 2.42E-03 1.80E-03 1.36E-03 1.35E-03 1.22E-03 9.44E-04 1.24E-04 1.00E-02 1.00E-02 1.00E-02 1.00E-02 1.00E-02 PASS PASS PASS PASS PASS An ISO 9001:2008 and DSCC Certified Company 90 RLAT Report 10-055 100219 R1.1 Average Biased Average Un-Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (+KTL) Biased Output Voltage Low, 1mA CH A @ VS=5V (V) 1.80E+00 1.60E+00 1.40E+00 1.20E+00 1.00E+00 8.00E-01 6.00E-01 4.00E-01 2.00E-01 0.00E+00 0 50 100 150 Total Dose (krad(Si)) Figure 5.43. Plot of Output Voltage Low, 1mA CH A @ VS=5V (V) versus total dose. The data show no significant change with total dose to the 100krad(Si) dose level and substantial degradation at the 200krad(Si) dose level. Note that this parameter is only specified to 100krad(Si) and the 200krad(Si) dose data is for reference only. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 91 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 10-055 100219 R1.1 Table 5.43. Raw data for Output Voltage Low, 1mA CH A @ VS=5V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Low, 1mA CH A @ VS=5V (V) Device 41 116 182 241 325 408 492 724 786 868 929 1012 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MAX Status Total Dose (krad(Si)) 0 2.46E-01 2.43E-01 2.42E-01 2.43E-01 2.42E-01 2.43E-01 2.42E-01 2.45E-01 2.46E-01 2.41E-01 2.43E-01 2.43E-01 20 2.47E-01 2.46E-01 2.45E-01 2.46E-01 2.45E-01 2.45E-01 2.44E-01 2.46E-01 2.48E-01 2.43E-01 2.44E-01 2.44E-01 50 2.50E-01 2.46E-01 2.47E-01 2.48E-01 2.46E-01 2.47E-01 2.46E-01 2.49E-01 2.50E-01 2.44E-01 2.44E-01 2.44E-01 100 2.56E-01 2.51E-01 2.53E-01 2.54E-01 2.52E-01 2.53E-01 2.52E-01 2.55E-01 2.56E-01 2.48E-01 2.44E-01 2.43E-01 200 2.76E-01 2.70E-01 2.73E-01 2.74E-01 2.69E-01 2.72E-01 2.72E-01 2.76E-01 2.78E-01 2.63E-01 2.43E-01 2.43E-01 2.43E-01 1.64E-03 2.48E-01 2.39E-01 2.46E-01 8.37E-04 2.48E-01 2.44E-01 2.47E-01 1.67E-03 2.52E-01 2.43E-01 2.53E-01 1.92E-03 2.58E-01 2.48E-01 2.72E-01 2.88E-03 2.80E-01 2.65E-01 2.43E-01 2.45E-01 2.47E-01 2.53E-01 2.72E-01 2.07E-03 1.92E-03 2.39E-03 3.11E-03 5.76E-03 2.49E-01 2.50E-01 2.54E-01 2.61E-01 2.88E-01 2.38E-01 2.40E-01 2.41E-01 2.44E-01 2.56E-01 3.50E-01 8.00E-01 1.00E+00 1.60E+00 1.60E+00 PASS PASS PASS PASS PASS An ISO 9001:2008 and DSCC Certified Company 92 RLAT Report 10-055 100219 R1.1 Average Biased Average Un-Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Ps90%/90% (+KTL) Biased Output Voltage Low, 1mA CH B @ VS=5V (V) 1.80E+00 1.60E+00 1.40E+00 1.20E+00 1.00E+00 8.00E-01 6.00E-01 4.00E-01 2.00E-01 0.00E+00 0 50 100 150 Total Dose (krad(Si)) Figure 5.44. Plot of Output Voltage Low, 1mA CH B @ VS=5V (V) versus total dose. The data show no significant change with total dose to the 100krad(Si) dose level and substantial degradation at the 200krad(Si) dose level. Note that this parameter is only specified to 100krad(Si) and the 200krad(Si) dose data is for reference only. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. An ISO 9001:2008 and DSCC Certified Company 93 200 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 10-055 100219 R1.1 Table 5.44. Raw data for Output Voltage Low, 1mA CH B @ VS=5V (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Low, 1mA CH B @ VS=5V (V) Device 41 116 182 241 325 408 492 724 786 868 929 1012 Biased Statistics Average Biased Std Dev Biased Ps90%/90% (+KTL) Biased Ps90%/90% (-KTL) Biased Un-Biased Statistics Average Un-Biased Std Dev Un-Biased Ps90%/90% (+KTL) Un-Biased Ps90%/90% (-KTL) Un-Biased Specification MAX Status Total Dose (krad(Si)) 0 2.41E-01 2.37E-01 2.37E-01 2.38E-01 2.37E-01 2.39E-01 2.38E-01 2.39E-01 2.40E-01 2.32E-01 2.38E-01 2.37E-01 20 2.43E-01 2.40E-01 2.40E-01 2.41E-01 2.40E-01 2.41E-01 2.39E-01 2.40E-01 2.42E-01 2.34E-01 2.40E-01 2.39E-01 50 2.45E-01 2.41E-01 2.42E-01 2.43E-01 2.41E-01 2.43E-01 2.42E-01 2.43E-01 2.44E-01 2.36E-01 2.39E-01 2.40E-01 100 2.50E-01 2.45E-01 2.47E-01 2.48E-01 2.46E-01 2.48E-01 2.47E-01 2.49E-01 2.49E-01 2.39E-01 2.40E-01 2.39E-01 200 2.66E-01 2.60E-01 2.62E-01 2.62E-01 2.59E-01 2.66E-01 2.64E-01 2.67E-01 2.68E-01 2.49E-01 2.39E-01 2.38E-01 2.38E-01 1.73E-03 2.43E-01 2.33E-01 2.41E-01 1.30E-03 2.44E-01 2.37E-01 2.42E-01 1.67E-03 2.47E-01 2.38E-01 2.47E-01 1.92E-03 2.52E-01 2.42E-01 2.62E-01 2.68E-03 2.69E-01 2.54E-01 2.38E-01 2.39E-01 2.42E-01 2.46E-01 2.63E-01 3.21E-03 3.11E-03 3.21E-03 4.22E-03 7.85E-03 2.46E-01 2.48E-01 2.50E-01 2.58E-01 2.84E-01 2.29E-01 2.31E-01 2.33E-01 2.35E-01 2.41E-01 3.50E-01 8.00E-01 1.00E+00 1.60E+00 1.60E+00 PASS PASS PASS PASS PASS An ISO 9001:2008 and DSCC Certified Company 94 RLAT Report 10-055 100219 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 6.0. Summary / Conclusions The total ionizing dose testing described in this final report was performed using the facilities at Radiation Assured Devices’ Longmire Laboratories in Colorado Springs, CO. The high dose rate total ionizing dose (TID) source is a JLSA 84-21 irradiator modified to provide a panoramic exposure. The Co-60 rods are held in the base of the irradiator heavily shielded by lead, during the radiation exposures the rod is raised by an electronic timer/controller and the exposure is performed in air. The dose rate for this irradiator in this configuration ranges from <1rad(Si)/s to a maximum of approximately 120rad(Si)/s, determined by the distance from the source. The parametric data was obtained as “read and record” and all the raw data plus an attributes summary were presented in this report. The attributes data contains the average, standard deviation and the average with the KTL values applied. The KTL value used was 2.742 per MIL HDBK 814 using onesided tolerance limits of 90/90 and a 5-piece sample size. Note that the following criteria was used to determine the outcome of the testing: following the radiation exposure each parameter had to pass the specification value and the average value for the five-piece sample must pass the specification value when the KTL limits are applied. If these conditions were not both satisfied following the radiation exposure, then the lot could be logged as an RLAT failure. Based on these criteria, the RH1013M operational amplifiers from the lot of material described on the first page of this report passed the RLAT to the maximum tested level of 100krad(Si) and 200krad(Si) without significant degradation to most of the measured parameters. As seen in the data plots, several parameters suffered measurable radiation-induced degradation, however in no case was the degradation sufficient to cause the parameters to go out of specification even after application of the KTL statistics. Note that PSSR for Channel A was out of specification pre-irradiation and at the first two dose levels. In our opinion this is due to the distribution within the sample population and is not reflective of radiation-induced degradation of the parameter. Further note that RH1013 is specified to 100krad(Si) in the +VS=5V, -VS=0 supply conditions and the 200krad(Si) data shown in this report for those parameters should be used for reference only. An ISO 9001:2008 and DSCC Certified Company 95 RLAT Report 10-055 100219 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Appendix A: Photograph of device-under-test to show part markings An ISO 9001:2008 and DSCC Certified Company 96 RLAT Report 10-055 100219 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Appendix B: TID Bias Connections (Extracted from LINEAR TECHNOLOGY CORPORATION RH1013M Dual Precision Operational Amplifier Datasheet) Biased Samples: Pin 1 2 3 4 5 6 7 8 9 10 Function OUT A -IN A +IN A NC VNC +IN B -IN B OUT B V+ Bias To Pin 2 Via 10kΩ Resistor To Pin 1 Via 10kΩ Resistor 8V Via 10kΩ Resistor NC -15V Decoupled to GND w/ 0.1μF NC 8V Via 10kΩ Resistor To Pin 9 Via 10kΩ Resistor To Pin 8 Via 10kΩ Resistor +15V Decoupled to GND w/ 0.1μF Unbiased Samples (All Pins Tied to Ground): Pin 1 2 3 4 5 6 7 8 9 10 Function OUT A -IN A +IN A NC VNC +IN B -IN B OUT B V+ Bias GND GND GND GND GND GND GND GND GND GND An ISO 9001:2008 and DSCC Certified Company 97 RLAT Report 10-055 100219 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Figure B.1. Irradiation bias drawing for the units to be irradiated under electrical bias. This figure was extracted from the LINEAR TECHNOLOGY CORPORATION RH1013M Dual Precision Operational Amplifier Datasheet. Figure B.2. W package drawing (for reference only). This figure was extracted from the LINEAR TECHNOLOGY CORPORATION RH1013M Dual Precision Operational Amplifier Datasheet. An ISO 9001:2008 and DSCC Certified Company 98 RLAT Report 10-055 100219 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Appendix C: Electrical Test Parameters and Conditions All electrical tests for this device are performed on Radiation Assured Device’s LTS2020 Test System. The LTS2020 Test System is a programmable parametric tester that provides parameter measurements for a variety of digital, analog and mixed signal products including voltage regulators, voltage comparators, D to A and A to D converters. The LTS2020 Test System achieves accuracy and sensitivity through the use of software self-calibration and an internal relay matrix with separate family boards and custom personality adapter boards. The tester uses this relay matrix to connect the required test circuits, select the appropriate voltage / current sources and establish the needed measurement loops for all the tests performed. The measured parameters and test conditions are shown in Table C.1. A listing of the measurement precision/resolution for each parameter is shown in Table C.2. The precision/resolution values were obtained either from test data or from the DAC resolution of the LTS2020. To generate the precision/resolution shown in Table C.2, one of the units-under-test was tested repetitively (a total of 10-times with re-insertion between tests) to obtain the average test value and standard deviation. Using this test data MIL-HDBK-814 90/90 KTL statistics were applied to the measured standard deviation to generate the final measurement range. This value encompasses the precision/resolution of all aspects of the test system, including the LTS2020 mainframe, family board, socket assembly and DUT board as well as insertion error. In some cases, the measurement resolution is limited by the internal DACs, which results in a measured standard deviation of zero. In these instances the precision/resolution will be reported back as the LSB of the DAC. Note that the testing and statistics used in this document are based on an “analysis of variables” technique, which relies on small sample sizes to qualify much larger lot sizes (see MIL-HDBK-814, p. 91 for a discussion of statistical treatments). Unfortunately, not all measured parameters are well suited to this approach due to inherent large variations in measurement accuracy or the sample population. One such parameter for this device is pre-irradiation power supply rejection ratio, where the device exhibits sensitivity to input conditions and has a relatively large distribution within the sample population, resulting in a pre-irradiation “failure” after application of the KTL statistics. If necessary, larger samples sizes could be used to qualify these parameters using an “attributes” approach. An ISO 9001:2008 and DSCC Certified Company 99 RLAT Report 10-055 100219 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Table C.1. Measured parameters and test conditions for the RH1013MW. Unless otherwise noted the conditions were selected to match the post-irradiation specifications. See LINEAR TECHNOLOGY CORPORATION RH1013M Dual Precision Operational Amplifier Datasheet for the post irradiation test conditions and specifications. Test Description Positive Supply Current Negative Supply Current Input Offset Voltage Input Offset Current + Input Bias Current - Input Bias Current Common Mode Rejection Ratio Power Supply Rejection Ratio Large Signal Voltage Gain Positive Output Voltage Swing Negative Output Voltage Swing Positive Slew Rate Negative Slew Rate Positive Supply Current @ VS=5V Negative Supply Current @ VS=5V Input Offset Voltage @ VS=5V Input Offset Current @ VS=5V + Input Bias Current @ VS=5V - Input Bias Current @ VS=5V Output Voltage High, No Load @ VS=5V Output Voltage High, 600Ω @ VS=5V Output Voltage Low, No Load @ VS=5V Output Voltage Low, 600Ω @ VS=5V Output Voltage Low, 1mA @ VS=5V Test Conditions VS=±15V VS=±15V VS=±15V VS=±15V VS=±15V VS=±15V VCM = 13V, –15V VS = ±10V to ±18V VS=±15V, VO = ±10V, RL = 10kΩ VS=±15V, RL= 10kΩ VS=±15V, RL= 10kΩ VS=±15V, RL= 10kΩ VS=±15V, RL= 10kΩ VS=+5V VS=+5V VS=+5V VS=+5V VS=+5V VS=+5V VS=+5V, No Load VS=+5V, RL = 600Ω VS=+5V, No Load VS=+5V, RL = 600Ω VS=+5V, ISINK = 1mA An ISO 9001:2008 and DSCC Certified Company 100 RLAT Report 10-055 100219 R1.1 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 Table C.2. Measured parameters, pre-irradiation specifications and measurement resolution for the RH1013MW. Measured Parameter Positive Supply Current Negative Supply Current Input Offset Voltage Input Offset Current + Input Bias Current - Input Bias Current Common Mode Rejection Ratio Power Supply Rejection Ratio Large Signal Voltage Gain Positive Output Voltage Swing Negative Output Voltage Swing Positive Slew Rate Negative Slew Rate Positive Supply Current @ VS=5V Negative Supply Current @ VS=5V Input Offset Voltage @ VS=5V Input Offset Current @ VS=5V + Input Bias Current @ VS=5V - Input Bias Current @ VS=5V Output Voltage High, No Load @ VS=5V Output Voltage High, 600Ω @ VS=5V Output Voltage Low, No Load @ VS=5V Output Voltage Low, 600Ω @ VS=5V Output Voltage Low, 1mA @ VS=5V Pre-Irradiation Specification 1.1mA MAX -1.1mA MIN ±300µV MAX ±10nA MAX ±30nA MAX ±30nA MAX 97dB MIN 100dB MIN 1200V/mV MIN 12.5V MIN -12.5V MAX 0.2V/ µs MIN -0.2V/ µs MAX 1.0mA MAX -1.0mA MIN ±450µV MAX ±10nA MAX ±50nA MAX ±50nA MAX 4V MIN 3.4V MIN 25mV MAX 10mV MAX 350mV MAX An ISO 9001:2008 and DSCC Certified Company 101 Measurement Precision/Resolution ±1.2E-6A ±1.2E-6A ±1.0E-6V ±2.0E-11A ±4.0E-11A ±4.0E-11A ±0.5dB ±1.0dB ±7.38E3V/mV ±1.0E-3V ±1.0E-3V ±1.08E-2V/ µs ±1.14E-2V/ µs ±3.05E-6A ±2.56E-6A ±5.8E-7V ±3.8E-11A ±4.23E-11A ±5.2E-11 ±1.0E-3V ±1.0E-3V ±1.0E-3V ±1.0E-3V ±1.0E-3V RLAT Report 10-055 100219 R1.1 Appendix D: List of Figures in the Results Section (Section 5) 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 5.10 5.11 5.12 5.13 5.14 5.15 5.16 5.17 5.18 5.19 5.20 5.21 5.22 5.23 5.24 5.25 5.26 5.27 5.28 5.29 5.30 5.31 5.32 5.33 5.34 5.35 5.36 5.37 5.38 5.39 Positive Supply Current (A) Negative Supply Current (A) Input Offset Voltage CH A (V) Input Offset Voltage CH B (V) Input Offset Current CH A (A) Input Offset Current CH B (A) + Input Bias Current CH A (A) + Input Bias Current CH B (A) - Input Bias Current CH A (A) - Input Bias Current CH B (A) Common Mode Rejection Ratio CH A (dB) Common Mode Rejection Ratio CH B (dB) Power Supply Rejection Ratio CH A (dB) Power Supply Rejection Ratio CH B (dB) Large Signal Voltage Gain CH A (V/mV) Large Signal Voltage Gain CH B (V/mV) Positive Output Voltage Swing CH A (V) Positive Output Voltage Swing CH B (V) Negative Output Voltage Swing CH A (V) Negative Output Voltage Swing CH B (V) Positive Slew Rate CH A (V/µs) Positive Slew Rate CH B (V/µs) Negative Slew Rate CH A (V/µs) Negative Slew Rate CH B (V/µs) Positive Supply Current @ VS=5V (A) Negative Supply Current @ VS=5V (A) Input Offset Voltage CH A @ VS=5V (V) Input Offset Voltage CH B @ VS=5V (V) Input Offset Current CH A @ VS=5V (V) Input Offset Current CH B @ VS=5V (A) + Input Bias Current CH A @ VS=5V (A) + Input Bias Current CH B @ VS=5V (A) - Input Bias Current CH A @ VS=5V (A) - Input Bias Current CH B @ VS=5V (A) Output Voltage High, No Load CH A @ VS=5V (V) Output Voltage High, No Load CH B @ VS=5V (V) Output Voltage High, 600Ω CH A @ VS=5V (V) Output Voltage High, 600Ω CH B @ VS=5V (V) Output Voltage Low, No Load CH A @ VS=5V (V) An ISO 9001:2008 and DSCC Certified Company 102 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800 RLAT Report 10-055 100219 R1.1 5.40 5.41 5.42 5.43 5.44 Output Voltage Low, No Load CH B @ VS=5V (V) Output Voltage Low, 600Ω CH A @ VS=5V (V) Output Voltage Low, 600Ω CH B @ VS=5V (V) Output Voltage Low, 1mA CH A @ VS=5V (V) Output Voltage Low, 1mA CH B @ VS=5V (V) An ISO 9001:2008 and DSCC Certified Company 103 Radiation Assured Devices 5017 N. 30th Street Colorado Springs, CO 80919 (719) 531-0800