MOTOROLA MTP4N50E

Order this document
by MTP4N50E/D
SEMICONDUCTOR TECHNICAL DATA
 
Motorola Preferred Device
N–Channel Enhancement–Mode Silicon Gate
TMOS POWER FET
4.0 AMPERES
500 VOLTS
RDS(on) = 1.5 OHMS
This advanced high voltage TMOS E–FET is designed to
withstand high energy in the avalanche mode and switch efficiently.
This new high energy device also offers a drain–to–source diode
with fast recovery time. Designed for high voltage, high speed
switching applications such as power supplies, PWM motor
controls and other inductive loads, the avalanche energy capability
is specified to eliminate the guesswork in designs where inductive
loads are switched and offer additional safety margin against
unexpected voltage transients.
• Avalanche Energy Capability Specified at Elevated
Temperature
• Low Stored Gate Charge for Efficient Switching
• Internal Source–to–Drain Diode Designed to Replace External
Zener Transient Suppressor — Absorbs High Energy in the
Avalanche Mode
• Source–to–Drain Diode Recovery Time Comparable to Discrete
Fast Recovery Diode

D
G
S
CASE 221A–06, Style 5
TO–220AB
MAXIMUM RATINGS (TC = 25°C unless otherwise noted)
Symbol
Value
Unit
Drain–Source Voltage
VDSS
500
Vdc
Drain–Gate Voltage (RGS = 1.0 MΩ)
VDGR
500
Vdc
Gate–Source Voltage — Continuous
Gate–Source Voltage — Non–repetitive
VGS
VGSM
± 20
± 40
Vdc
Vpk
Drain Current — Continuous
Drain Current — Pulsed
ID
IDM
4.0
10
Adc
Total Power Dissipation @ TC = 25°C
Derate above 25°C
PD
75
0.6
Watts
W/°C
TJ, Tstg
– 55 to 150
°C
WDSR (1)
mJ
WDSR (2)
280
44
7.4
RθJC
RθJA
1.67
62.5
°C/W
TL
260
°C
Rating
Operating and Storage Temperature Range
UNCLAMPED DRAIN–TO–SOURCE AVALANCHE CHARACTERISTICS (TJ < 150°C)
Single Pulse Drain–to–Source Avalanche Energy — TJ = 25°C
Single Pulse Drain–to–Source Avalanche Energy — TJ = 100°C
Repetitive Pulse Drain–to–Source Avalanche Energy
THERMAL CHARACTERISTICS
Thermal Resistance — Junction to Case
Thermal Resistance — Junction to Ambient°
Maximum Lead Temperature for Soldering Purposes, 1/8″ from case for 10 seconds
(1) VDD = 50 V, ID = 4.0 A
(2) Pulse Width and frequency is limited by TJ(max) and thermal response
Designer’s Data for “Worst Case” Conditions — The Designer’s Data Sheet permits the design of most circuits entirely from the information presented. SOA Limit
curves — representing boundaries on device characteristics — are given to facilitate “worst case” design.
E–FET and Designer’s are trademarks of Motorola, Inc. TMOS is a registered trademark of Motorola, Inc.
Preferred devices are Motorola recommended choices for future use and best overall value.
REV 1
TMOS
 Motorola
Motorola, Inc.
1996
Power MOSFET Transistor Device Data
1
MTP4N50E
ELECTRICAL CHARACTERISTICS (TJ = 25°C unless otherwise noted)
Characteristic
Symbol
Min
Typ
Max
Unit
V(BR)DSS
500
—
—
Vdc
—
—
—
—
0.25
1.0
OFF CHARACTERISTICS
Drain–to–Source Breakdown Voltage
(VGS = 0, ID = 250 µAdc)
Zero Gate Voltage Drain Current
(VDS = 500 V, VGS = 0)
(VDS = 400 V, VGS = 0, TJ = 125°C)
IDSS
mAdc
Gate–Body Leakage Current, Forward (VGSF = 20 Vdc, VDS = 0)
IGSSF
—
—
100
nAdc
Gate–Body Leakage Current, Reverse (VGSR = 20 Vdc, VDS = 0)
IGSSR
—
—
100
nAdc
2.0
1.5
—
—
4.0
3.5
—
1.3
1.5
—
—
—
—
7.5
6.0
gFS
1.5
—
—
mhos
Ciss
—
775
—
pF
Coss
—
84
—
Crss
—
19
—
td(on)
—
24
—
ON CHARACTERISTICS*
Gate Threshold Voltage
(VDS = VGS, ID = 250 µAdc)
(TJ = 125°C)
VGS(th)
Static Drain–Source On–Resistance (VGS = 10 Vdc, ID = 2.0 A)
RDS(on)
Drain–Source On–Voltage (VGS = 10 Vdc)
(ID = 4.0 Adc)
(ID = 2.0 A, TJ = 100°C)
VDS(on)
Forward Transconductance (VDS = 15 Vdc, ID = 2.0 A)
Vdc
Ohm
Vdc
DYNAMIC CHARACTERISTICS
Input Capacitance
Output Capacitance
(VDS = 25 V, VGS = 0,
f = 1.0 MHz)
Transfer Capacitance
SWITCHING CHARACTERISTICS*
Turn–On Delay Time
Rise Time
Turn–Off Delay Time
(VDD = 250 V, ID ≈ 4.0 A,
RG = 12 Ω, RL = 62 Ω,
VGS(on) = 10 V)
Fall Time
Total Gate Charge
Gate–Source Charge
(VDS = 400 V, ID = 4.0 A,
VGS = 10 V)
Gate–Drain Charge
ns
tr
—
34
—
td(off)
—
60
—
tf
—
36
—
Qg
—
27
32
Qgs
—
3.5
—
Qgd
—
14
—
VSD
—
—
1.4
Vdc
ton
—
**
—
ns
trr
—
—
760
—
—
3.5
4.5
—
—
—
7.5
—
nC
SOURCE–DRAIN DIODE CHARACTERISTICS
Forward On–Voltage
Forward Turn–On Time
(IS = 4.0 A, di/dt = 100 A/µs)
Reverse Recovery Time
INTERNAL PACKAGE INDUCTANCE
Internal Drain Inductance
(Measured from the contact screw on tab to center of die)
(Measured from the drain lead 0.25″ from package to center of die)
Ld
Internal Source Inductance
(Measured from the source lead 0.25″ from package to source bond pad)
Ls
nH
* Indicates Pulse Test: Pulse Width = 300 µs Max, Duty Cycle ≤ 2.0%.
** Limited by circuit inductance.
2
Motorola TMOS Power MOSFET Transistor Device Data
MTP4N50E
8
I D, DRAIN CURRENT (AMPS)
TJ = 25°C
VGS = 10 V
8V
6
7V
4
6V
2
5V
4V
0
0
4
8
12
16
VDS, DRAIN–TO–SOURCE VOLTAGE (VOLTS)
20
VGS(th), GATE THRESHOLD VOLTAGE (NORMALIZED)
TYPICAL ELECTRICAL CHARACTERISTICS
1.2
1
0.9
0.8
–50
Figure 1. On–Region Characteristics
VBR(DSS), DRAIN–TO–SOURCE BREAKDOWN
VOLTAGE (NORMALIZED)
I D, DRAIN CURRENT (AMPS)
VDS ≥ 10 V
6
4
2
25°C
–55°C
0
0
2
4
6
8
VGS, GATE–TO–SOURCE VOLTAGE (VOLTS)
10
1.1
2
1.6
25°C
1.2
0.8
–55°C
0
4
6
8
VGS = 0
ID = 0.25 mA
1
0.9
0.8
–50
RDS(on) , DRAIN–TO–SOURCE RESISTANCE
(NORMALIZED)
RDS(on) , DRAIN–TO–SOURCE RESISTANCE (OHMS)
TJ = 100°C
2
150
0
50
100
150
200
Figure 4. Breakdown Voltage Variation
With Temperature
VGS = 10 V
0
125
TJ, JUNCTION TEMPERATURE (°C)
2.8
0.4
0
25
50
75
100
TJ, JUNCTION TEMPERATURE (°C)
1.2
Figure 3. Transfer Characteristics
2.4
–25
Figure 2. Gate–To–Source Threshold Voltage
Variation With Temperature
8
TJ = 100°C
VDS = VGS
ID = 0.25 mA
1.1
10
2.5
2
VGS = 10 V
ID = 2 A
1.5
1
0.5
0
–50
0
50
100
150
ID, DRAIN CURRENT (AMPS)
TJ, JUNCTION TEMPERATURE (°C)
Figure 5. On–Resistance versus Drain Current
Figure 6. On–Resistance Variation
With Temperature
Motorola TMOS Power MOSFET Transistor Device Data
200
3
MTP4N50E
SAFE OPERATING AREA INFORMATION
10 µs
12
0.1 ms
VGS = 20 V
SINGLE PULSE
TC = 25°C
1
1 ms
10 ms
RDS(on) LIMIT
THERMAL LIMIT
PACKAGE LIMIT
0.1
14
I D, DRAIN CURRENT (AMPS)
I D, DRAIN CURRENT (AMPS)
10
10
8
6
TJ ≤ 150°C
4
2
dc
0
10
100
VDS, DRAIN–TO–SOURCE VOLTAGE (VOLTS)
1
1000
0
100
200
300
400
500
VDS, DRAIN–TO–SOURCE VOLTAGE (VOLTS)
Figure 7. Maximum Rated Forward Biased
Safe Operating Area
600
Figure 8. Maximum Rated Switching
Safe Operating Area
The FBSOA curves define the maximum drain–to–source
voltage and drain current that a device can safely handle
when it is forward biased, or when it is on, or being turned on.
Because these curves include the limitations of simultaneous
high voltage and high current, up to the rating of the device,
they are especially useful to designers of linear systems. The
curves are based on a case temperature of 25°C and a maximum junction temperature of 150°C. Limitations for repetitive
pulses at various case temperatures can be determined by
using the thermal response curves. Motorola Application
Note, AN569, “Transient Thermal Resistance–General Data
and Its Use” provides detailed instructions.
The power averaged over a complete switching cycle must
be less than:
TJ(max) – TC
RθJC
10000
VDD = 250 V
ID = 4 A
VGS = 10 V
TJ = 25°C
1000
td(off)
tf
tr
t, TIME (ns)
FORWARD BIASED SAFE OPERATING AREA
td(on)
100
SWITCHING SAFE OPERATING AREA
The switching safe operating area (SOA) of Figure 8 is the
boundary that the load line may traverse without incurring
damage to the MOSFET. The fundamental limits are the
peak current, IDM and the breakdown voltage, V(BR)DSS. The
switching SOA shown in Figure 8 is applicable for both turn–
on and turn–off of the devices for switching times less than
one microsecond.
10
1
1000
10
100
RG, GATE RESISTANCE (OHMS)
Figure 9. Resistive Switching Time
Variation versus Gate Resistance
r(t), NORMALIZED EFFECTIVE
TRANSIENT THERMAL RESISTANCE
1
0.5
0.3
D = 0.5
0.2
0.2
0.1
0.1
P(pk)
0.05
0.05
0.02
t1
0.03
0.02
t2
DUTY CYCLE, D = t1/t2
0.01
SINGLE PULSE
0.01
0.01
0.02
0.05
0.1
0.2
0.5
1
2
5
t, TIME (ms)
10
20
RθJC(t) = r(t) RθJC
RθJC = 1.67°C/W MAX
D CURVES APPLY FOR POWER
PULSE TRAIN SHOWN
READ TIME AT t1
TJ(pk) – TC = P(pk) RθJC(t)
50
100
200
500
1000
Figure 10. Thermal Response
4
Motorola TMOS Power MOSFET Transistor Device Data
MTP4N50E
2000
VGS, GATE SOURCE VOLTAGE (VOLTS)
16
TJ = 25°C
VGS = 0
C, CAPACITANCE (pF)
1500
1000
Crss
Ciss
500
VDS = 0
0
Coss
TJ = 25°C
ID = 4 A
VDS = 100 V
12
250 V
400 V
8
4
0
5
5
10
20
25
15
0
VGS
VDS
GATE–TO–SOURCE OR DRAIN–TO–SOURCE VOLTAGE (VOLTS)
10
0
10
20
30
QG, TOTAL GATE CHARGE (nC)
40
50
Figure 12. Gate Charge versus
Gate–To–Source Voltage
Figure 11. Capacitance Variation
COMMUTATING SAFE OPERATING AREA (CSOA)
The Commutating Safe Operating Area (CSOA) of
Figure 14 defines the limits of safe operation for commutated
source–drain current versus re–applied drain voltage when
the source–drain diode has undergone forward bias. The
curve shows the limitations of IFM and peak VDS for a given
rate of change of source current. It is applicable when waveforms similar to those of Figure 13 are present. Full or half–
bridge PWM DC motor controllers are common applications
requiring CSOA data.
Device stresses increase with increasing rate of change of
source current so dIs/dt is specified with a maximum value.
Higher values of dIs/dt require an appropriate derating of IFM,
peak VDS or both. Ultimately dIs/dt is limited primarily by device, package, and circuit impedances. Maximum device
stress occurs during trr as the diode goes from conduction to
reverse blocking.
VDS(pk) is the peak drain–to–source voltage that the device
must sustain during commutation; IFM is the maximum forward source–drain diode current just prior to the onset of
commutation.
VR is specified at 80% of V(BR)DSS to ensure that the
CSOA stress is maximized as IS decays from IRM to zero.
RGS should be minimized during commutation. TJ has only
a second order effect on CSOA.
Stray inductances in Motorola’s test circuit are assumed to
be practical minimums. dVDS/dt in excess of 10 V/ns was attained with dIs/dt of 400 A/µs.
15 V
VGS
0
IFM
dls/dt
90%
IS
10%
trr
ton
IRM
0.25 IRM
VDS(pk)
VR
VDS
dVDS/dt
VdsL
Vf
MAX. CSOA
STRESS AREA
Figure 15. Commutating Waveforms
6
I D, DRAIN CURRENT (AMPS)
RGS
4
DUT
–
VR
+
di/dt ≤ 75 A/µs
2
IS
+
VGS
0
IFM
0
500
100
200
300
400
VDS, DRAIN–TO–SOURCE VOLTAGE (VOLTS)
600
Figure 13. Commutating Safe Operating Area (CSOA)
Motorola TMOS Power MOSFET Transistor Device Data
Li
VDS
20 V
–
VR = 80% OF RATED VDS
VdsL = Vf + Li ⋅ dls/dt
Figure 14. Commutating Safe Operating Area
Test Circuit
5
MTP4N50E
V(BR)DSS
Vds(t)
IO
L
VDS
ID(t)
C
4700 µF
250 V
ID
VDD
VDD
t
WDSR
Figure 16. Unclamped Inductive Switching
Test Circuit
ǒ Ǔǒ
Ǔ
t, (TIME)
tP
RGS
50 Ω
+
1 LI 2
O
2
V(BR)DSS
V(BR)DSS – VDD
Figure 17. Unclamped Inductive Switching
Waveforms
RESISTIVE SWITCHING
VDD
ton
td(on)
RL
Vout
Vin
PULSE GENERATOR
Rgen
50 Ω
tf
90%
OUTPUT, Vout
INVERTED
10%
90%
50 Ω
INPUT, Vin
50%
50%
10%
PULSE WIDTH
* Note: The Mirror is shorted to the Kelvin terminal for this test.
Figure 18. Switching Test Circuit
Figure 19. Switching Waveforms
+18 V
VDD
1 mA
47 k
Vin
td(off)
tr
90%
DUT
z = 12 Ω
toff
10 V
15 V
SAME
DEVICE TYPE
AS DUT
100 k
2N3904
0.1 µF
2N3904
100 k
47 k
100
FERRITE
BEAD
DUT
Vin = 15 Vpk; PULSE WIDTH ≤ 100 µs, DUTY CYCLE ≤ 10%
Figure 20. Gate Charge Test Circuit
6
Motorola TMOS Power MOSFET Transistor Device Data
MTP4N50E
PACKAGE DIMENSIONS
–T–
B
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION Z DEFINES A ZONE WHERE ALL
BODY AND LEAD IRREGULARITIES ARE
ALLOWED.
SEATING
PLANE
C
F
T
S
4
A
Q
1 2 3
STYLE 5:
PIN 1.
2.
3.
4.
U
H
K
Z
L
R
V
J
G
D
N
GATE
DRAIN
SOURCE
DRAIN
DIM
A
B
C
D
F
G
H
J
K
L
N
Q
R
S
T
U
V
Z
INCHES
MIN
MAX
0.570
0.620
0.380
0.405
0.160
0.190
0.025
0.035
0.142
0.147
0.095
0.105
0.110
0.155
0.018
0.025
0.500
0.562
0.045
0.060
0.190
0.210
0.100
0.120
0.080
0.110
0.045
0.055
0.235
0.255
0.000
0.050
0.045
–––
–––
0.080
MILLIMETERS
MIN
MAX
14.48
15.75
9.66
10.28
4.07
4.82
0.64
0.88
3.61
3.73
2.42
2.66
2.80
3.93
0.46
0.64
12.70
14.27
1.15
1.52
4.83
5.33
2.54
3.04
2.04
2.79
1.15
1.39
5.97
6.47
0.00
1.27
1.15
–––
–––
2.04
CASE 221A–06
ISSUE Y
Motorola TMOS Power MOSFET Transistor Device Data
7
MTP4N50E
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit,
and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters can and do vary in different
applications. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does
not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in
systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of
the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such
unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless
against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part.
Motorola and
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer.
How to reach us:
USA / EUROPE: Motorola Literature Distribution;
P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447
JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, Toshikatsu Otsuki,
6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–3521–8315
MFAX: [email protected] – TOUCHTONE (602) 244–6609
INTERNET: http://Design–NET.com
HONG KONG: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
8
◊
*MTP4N50E/D*
Motorola TMOS Power MOSFET Transistor
Device Data
MTP4N50E/D