ETC AD9054BST

a
FEATURES
200 MSPS Guaranteed Conversion Rate
135 MSPS Low Cost Version Available
350 MHz Analog Bandwidth
1 V p-p Analog Input Range
Internal +2.5 V Reference and T/H
Low Power: 500 mW
+5 V Single Supply Operation
TTL Output Interface
Single or Demultiplexed Output Ports
APPLICATIONS
RGB Graphics Processing
High Resolution Video
Digital Data Storage Read Channels
Digital Communications
Digital Instrumentation
Medical Imaging
GENERAL DESCRIPTION
The AD9054A is an 8-bit monolithic analog-to-digital converter
optimized for high speed, low power, small size and ease of use.
With a 200 MSPS encode rate capability and full-power analog
bandwidth of 350 MHz, the component is ideal for applications
requiring the highest possible dynamic performance.
To minimize system cost and power dissipation, the AD9054A
includes an internal +2.5 V reference and track-and-hold circuit.
The user provides only a +5 V power supply and an encode clock.
No external reference or driver components are required for
many applications.
8-Bit, 200 MSPS
A/D Converter
AD9054A
FUNCTIONAL BLOCK DIAGRAM
VREF IN
AD9054A
AIN
T/H
AIN
ENCODE
ENCODE
VREF OUT
12.5V REFERENCE
QUANTIZER
8
ENCODE
LOGIC
8
DEMULTIPLEXER
TIMING
VDD
GND
DEMUX
DS
DA7 –DA0
DB7 –DB0
DS
The AD9054A’s encode input interfaces directly to TTL, CMOS
or positive-ECL logic and will operate with single-ended or
differential inputs. The user may select dual-channel or singlechannel digital outputs. The dual (demultiplexed) mode interleaves ADC data through two 8-bit channels at one-half the
clock rate. Operation in demultiplexed mode reduces the speed
and cost of external digital interfaces while allowing the ADC to
be clocked to the full 200 MSPS conversion rate. In the singlechannel (nondemultiplexed) mode, all data is piped at the full
clock rate to the Channel A outputs.
Fabricated with an advanced BiCMOS process, the AD9054A is
provided in a space-saving 44-lead LQFP surface mount plastic
package (ST-44) and specified over the full industrial (–40°C to
+85°C) temperature range.
REV. A
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
World Wide Web Site: http://www.analog.com
Fax: 781/326-8703
© Analog Devices, Inc., 2000
AD9054A–SPECIFICATIONS
ELECTRICAL CHARACTERISTICS (V
Parameter
Temp
DD
= +5 V, external reference, fS = max unless otherwise noted)
Test
Level
AD9054ABST-200
Min
Typ
Max
RESOLUTION
DC ACCURACY
Differential Nonlinearity
8
± 0.9
± 1.0
± 0.6
± 0.9
␣ ␣ ␣ ␣ ␣ ␣ Guaranteed
±2
160
8
+25°C
Full
+25°C
Full
Full
+25°C
Full
I
VI
I
VI
VI
I
V
Full
Full
+25°C
Full
+25°C
Full
+25°C
+25°C
Full
+25°C
V
V
I
VI
I
VI
V
I
VI
V
REFERENCE OUTPUT
Output Voltage
Temperature Coefficient
Full
Full
VI
V
2.4
SWITCHING PERFORMANCE
Maximum Conversion Rate (f S)
Minimum Conversion Rate (f S)
Encode Pulsewidth High (tEH)
Encode Pulsewidth Low (t EL)
Aperture Delay (tA)
Aperture Uncertainty (Jitter)
Data Sync Setup Time (tSDS)
Data Sync Hold Time (tHDS)
Data Sync Pulsewidth (tPWDS)
Output Valid Time (tV) 3
Output Propagation Delay (tPD) 3
Full
Full
+25°C
+25°C
+25°C
+25°C
+25°C
+25°C
+25°C
Full
Full
VI
IV
IV
IV
V
V
IV
IV
IV
VI
VI
200
DIGITAL INPUTS
HIGH Level Current (IIH) 4
LOW Level Current (IIL) 4
Input Capacitance
Full
Full
+25°C
VI
VI
V
DIFFERENTIAL INPUTS
Differential Signal Amplitude (VID)
HIGH Input Voltage (V IHD)
LOW Input Voltage (V ILD)
Common-Mode Input (VICM )
Full
Full
Full
Full
IV
IV
IV
IV
400
1.5
0
1.5
VDD
VDD – 0.4
DEMUX INPUT
HIGH Input Voltage (V IH)
LOW Input Voltage (V IL)
Full
Full
IV
IV
2.0
0
VDD
0.8
Full
Full
VI
VI
2.4
Integral Nonlinearity
No Missing Codes
Gain Error1
Gain Tempco 1
ANALOG INPUT
Input Voltage Range
(With Respect to AIN)
Compliance Range AIN or AIN
Input Offset Voltage
Input Resistance
Input Capacitance
Input Bias Current
Analog Bandwidth, Full Power2
DIGITAL OUTPUTS
HIGH Output Voltage (V OH)
LOW Output Voltage (V OL)
Output Coding
AD9054ABST-135
Min
Typ
Max
± 0.9
± 1.0
± 0.6
± 0.9
Guaranteed
±2
160
+1.5/–1.0
+2.0/–1.0
± 1.5
± 2.0
␣␣␣␣␣␣
±7
± 512
1.8
36
23
±4
±8
62
4
25
1.8
36
23
2.6
2.4
LSB
LSB
LSB
LSB
±7
% FS
ppm/°C
3.2
± 16
± 19
50
75
2.5
110
2.6
135
5.1
5.9
500
500
3
25
22
22
3.0
3.0
0.5
2.3
0.5
2.3
0
0.5
2.0
2.7
7.9
5.7
7.5
8.5
V
ppm/°C
MSPS
MSPS
ns
ns
ns
ps rms
ns
ns
ns
ns
ns
µA
µA
pF
400
1.5
0
1.5
VDD
VDD – 0.4
mV
V
V
V
2.0
0
VDD
0.8
V
V
0.4
V
V
500
500
3
2.4
Binary
mV p-p
V
mV
mV
kΩ
kΩ
pF
µA
µA
MHz
625
625
625
625
0.4
–2–
+1.5/–1.0
+2.0/–1.0
± 1.5
± 2.0
350
25
22
22
2.0
2.0
0
0.5
2.0
2.7
±4
±8
62
4
25
50
75
350
2.5
110
Bits
± 512
3.2
± 16
± 19
Units
Binary
REV. A
AD9054A
Parameter
Temp
Test
Level
POWER SUPPLY
VDD Supply Current (IDD)
Power Dissipation 5, 6
Power Supply Sensitivity7
Full
Full
+25°C
DYNAMIC PERFORMANCE8
Transient Response
Overvoltage Recovery Time
Signal-to-Noise Ratio (SNR)
(Without Harmonics)
fIN = 19.7 MHz
fIN = 49.7 MHz
fIN = 70.1 MHz
Signal-to-Noise Ratio (SINAD)
(With Harmonics)
fIN = 19.7 MHz
fIN = 49.7 MHz
fIN = 70.1 MHz
Effective Number of Bits
fIN = 19.7 MHz
fIN = 49.7 MHz
fIN = 70.1 MHz
2nd Harmonic Distortion
fIN = 19.7 MHz
fIN = 49.7 MHz
fIN = 70.1 MHz
3rd Harmonic Distortion
fIN = 19.7 MHz
fIN = 49.7 MHz
fIN = 70.1 MHz
Two-Tone Intermod Distortion
(IMD)
fIN = 19.7 MHz
fIN = 49.7 MHz
fIN = 70.1 MHz
AD9054ABST-200
Min
Typ
Max
AD9054ABST-135
Min
Typ
Max
VI
VI
I
128
640
0.005
120
600
0.005
+25°C
+25°C
V
V
1.5
1.5
+25°C
Full
+25°C
Full
+25°C
Full
IV
V
I
V
I
V
+25°C
Full
+25°C
Full
+25°C
Full
IV
V
I
V
I
V
+25°C
+25°C
+25°C
IV
I
I
+25°C
+25°C
+25°C
42
145
725
0.015
140
700
0.015
Units
mA
mW
V/V
1.5
1.5
ns
ns
45
45
45
45
dB
dB
dB
dB
dB
dB
43
43
43
43
dB
dB
dB
dB
dB
dB
45
45
45
45
45
45
42
43
43
43
43
42
42
40
6.35
6.35
6.18
6.85
6.85
6.85
6.35
6.35
6.85
6.85
Bits
Bits
Bits
IV
I
I
58
54
49
63
59
55
58
54
63
59
dBc
dBc
dBc
+25°C
+25°C
+25°C
IV
I
I
48
48
43
56
54
50
48
48
56
54
dBc
dBc
dBc
+25°C
+25°C
+25°C
V
V
V
60
55
dBc
dBc
dBc
42
42
40
40
39
60
55
50
42
40
NOTES
1
Gain error and gain temperature coefficient are based on the ADC only (with a fixed +2.5 V external reference).
2
3 dB bandwidth with full-power input signal.
3
tV and tPD are measured from the threshold crossing of the ENCODE input to valid TTL levels of the digital outputs. The output ac load during test is 5 pF (Refer to
equivalent circuits Figures 5 and 6).
4
I IH and IIL are valid for differential input voltages of less than 1.5 V. At higher differential voltages, the input current will increase to a maximum of 1.5 mA.
5
Power dissipation is measured under the following conditions: analog input is –1 dBFS at 19.7 MHz.
6
Typical thermal impedance for the ST-44 (LQFP) 44-lead package (in still air): θ JC = 20°C/W, θ CA = 35°C/W, θJA = 55°C/W.
7
A change in input offset voltage with respect to a change in V DD.
8
SNR/harmonics based on an analog input voltage of –1.0 dBFS referenced to a 1.024 V full-scale input range.
Specifications subject to change without notice.
IV. Parameter is guaranteed by design and characterization testing.
EXPLANATION OF TEST LEVELS
Test Level
V. Parameter is a typical value only.
I. 100% production tested.
VI. 100% production tested at +25°C; guaranteed by design
and characterization testing for industrial temperature range.
II. 100% production tested at +25°C and sample tested at
specified temperatures.
III. Sample tested only.
REV. A
–3–
AD9054A
ABSOLUTE MAXIMUM RATINGS*
Table I. Output Coding
VDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +6 V
Analog Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . VDD to 0.0 V
Digital Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . VDD to 0.0 V
VREF IN, VREF OUT . . . . . . . . . . . . . . . . . . . VDD to 0.0 V
Digital Output Current . . . . . . . . . . . . . . . . . . . . . . . . 20 mA
Operating Temperature . . . . . . . . . . . . . . . . –55°C to +125°C
Storage Temperature . . . . . . . . . . . . . . . . . . –65°C to +150°C
Maximum Junction Temperature . . . . . . . . . . . . . . . +175°C
Maximum Case Temperature . . . . . . . . . . . . . . . . . . +150°C
*Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions outside of those indicated in the operation
sections of this specification is not implied. Exposure to absolute maximum ratings
for extended periods may affect device reliability.
ORDERING GUIDE
Model
Temperature
Range
Package
Option*
AD9054ABST-200
AD9054ABST-135
AD9054A/PCB
–40°C to +85°C
–40°C to +85°C
+25°C
ST-44
ST-44
Evaluation Board
Step
AIN–AIN
Code
Binary
255
254
253
•
•
•
129
128
127
126
•
•
•
2
1
0
≥0.512 V
0.508 V
0.504 V
•
•
•
0.006 V
0.002 V
–0.002 V
–0.006 V
•
•
•
–0.504 V
–0.508 V
≤–0.512 V
255
254
253
•
•
•
129
128
127
126
•
•
•
2
1
0
1111 1111
1111 1110
1111 1101
•
•
•
1000 0001
1000 0000
0111 1111
0111 1110
•
•
•
0000 0010
0000 0001
0000 0000
*ST = Plastic Thin Quad Flatpack (LQFP).
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the AD9054A features proprietary ESD protection circuitry, permanent damage may
occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.
–4–
WARNING!
ESD SENSITIVE DEVICE
REV. A
AD9054A
34
38
39
42
43
44
DB4
DB6
DB2
VDD
DB1
GND
DB0 (LSB)
AIN
Ground.
VDD
AD9054A
AIN
GND
TOP VIEW
(PINS DOWN)
GND
GND
VDD
Digital Outputs of ADC Channel
A. DA7 is the MSB, DA0 the LSB.
DB0–DB 7
Digital Outputs of ADC Channel
B. DB7 is the MSB, DB0 the LSB.
VREF OUT Internal Reference Output
(+2.5 V typical); Bypass with
0.1 µF to Ground.
VREF IN
Reference Input for ADC (+2.5 V
typical, ± 4%).
AIN
Analog Input—Complement.
Connect to input signal midscale
reference.
AIN
Analog Input—True.
DEMUX
Format Select. LOW = Dual.
Channel Mode, HIGH = Single.
Channel Mode (Channel A Only).
DS
Data Sync Complement.
DS
Data Sync—Aligns output channels in Dual-Channel Mode.
DA0 (LSB)
DS
DA1
PIN 1
IDENTIFIER
SAMPLE N+3
DA3
DA4
DA5
DA6
DA7 (MSB)
GND
VDD
DA2
GND
DS
SAMPLE N
SAMPLE N–1
VDD
DEMUX
VDD
33
DB3
GND
ENCODE
19–26
VREF IN
ENCODE
3, 5, 15, 18, 28,
VDD
30, 31, 36, 41
4, 6, 16, 17, 27,
GND
29, 32, 35, 37, 40
14–7
DA0 –DA7
DB5
ENCODE
DB7 (MSB)
2
Encode Clock for ADC (ADC
Samples on Rising Edge of
ENCODE).
Encode Clock Complement
(ADC Samples on Falling Edge
of ENCODE).
Power Supply (+5 V).
GND
ENCODE
VDD
1
GND
Function
VDD
Name
GND
Pin Number
VDD
PIN CONFIGURATION
VREF OUT
PIN FUNCTION DESCRIPTIONS
SAMPLE N+4
AIN
SAMPLE N+1
tA
tEH
tEL
SAMPLE N+2
1/fS
ENCODE
ENCODE
tPD
D7 –D 0
DATA N–5
DATA N–4
DATA N–3
DATA N–2
Figure 1. Timing—Single Channel Mode
REV. A
–5–
DATA N–1
tV
DATA N
AD9054A
SAMPLE N
SAMPLE N–1
SAMPLE N+3
SAMPLE N+4
SAMPLE N+5
AIN
SAMPLE N–2
SAMPLE N+1
tA
tEH
tEL
tHDS
SAMPLE N+6
1/fS
ENCODE
ENCODE
SAMPLE N+2
tHDS
tSDS
tSDS
DS
DS
tPD
tPWDS
PORT A
D7 –D 0
DATA N–7
OR N–8
PORT B
D7 –D 0
DATA N–8
OR N–7
INVALID IF OUT OF SYNC
DATA N–4 IF IN SYNC
DATA N–7
OR N–6
DATA N–6
OR N–7
INVALID IF OUT OF SYNC
DATA N–5 IF IN SYNC
tV
DATA N
DATA N–2
DATA N–3
DATA N+1
DATA N–1
Figure 2a. Timing—Dual Channel Mode (One-Shot Data Sync)
SAMPLE N
SAMPLE N–1
SAMPLE N+3
SAMPLE N+4
SAMPLE N+5
AIN
SAMPLE N–2
SAMPLE N+1
tA
tEH
tEL
SAMPLE N+2
SAMPLE N+6
1/fS
ENCODE
ENCODE
tHDS
tSDS tHDS
tSDS
DS
DS
tPWDS
PORT A
D7 –D 0
DATA N–7
OR N–8
PORT B
D7 –D 0
DATA N–8
OR N–7
tPD
DATA N–7
OR N–6
DATA N–6
OR N–7
INVALID IF OUT OF SYNC
DATA N–4 IF IN SYNC
INVALID IF OUT OF SYNC
DATA N–5 IF IN SYNC
tV
DATA N
DATA N–2
DATA N–3
DATA N–1
DATA N+1
Figure 2b. Timing—Dual Channel Mode (Continuous Data Sync)
–6–
REV. A
AD9054A
EQUIVALENT CIRCUITS
VDD
17.5k⍀
DEMUX
300⍀
VDD
300⍀
AIN
AIN
7.5k⍀
Figure 6. Equivalent DEMUX Input Circuit
Figure 3. Equivalent Analog Input Circuit
VDD
VDD
VREF IN
DIGITAL
OUTPUTS
Figure 4. Equivalent Reference Input Circuit
Figure 7. Equivalent Digital Output Circuit
VDD
VDD
17.5kV
ENCODE
OR DS
300V
300V
ENCODE
OR DS
VREF
OUT
7.5kV
Figure 5. Equivalent ENCODE and Data Select Input Circuit
REV. A
Figure 8. Equivalent Reference Output Circuit
–7–
AD9054A
55
45.4
45.2
50
45.0
SINAD
40
44.8
44.6
70MHz
44.4
NYQUIST
FREQUENCY
(100MHz)
35
30
20MHz
50MHz
45
SNR – dB
SNR – dB
SNR
0
20
40
60
80
fIN – MHz
44.2
100
120
44.0
–45
140
Figure 9. SNR vs. fIN: fS = 200 MSPS
0
25
TC – 8C
70
90
Figure 12. SNR vs. Temperature, f S = 135 MSPS
50
46.0
49
45.8
48
45.6
47
45.4
46
45.2
20MHz
SNR – dB
SNR – dB
50MHz
SNR
45
44
SINAD
44.8
43
44.6
42
44.4
41
44.2
40
25
50
75
100 125 150 175 200 225 250 270
fS – MSPS
44.0
–60
300
Figure 10. SNR vs. f S: fIN = 19.7 MHz
–40
–20
0
20
TC – 8C
40
60
80
100
Figure 13. SNR vs. Temperature, f S = 200 MSPS
50
50
48
SNR
45
fS = 135MSPS
fIN = 10.3MHz
46
SINAD
44
SNR – dB
40
SNR – dB
70MHz
45.0
35
42
SNR
40
38
SINAD
30
36
34
25
32
20
25
50
75
30
0.0
100 125 150 175 200 225 250 270 300
fS – MSPS
Figure 11. SNR vs. f S: fIN = 70.1 MHz
1.0
2.0
3.0
4.0
5.0
6.0
ENCODE PULSEWIDTH – ns
7.0
8.0
Figure 14. SNR vs. Clock Pulsewidth, (tPWH): fS = 135 MSPS
–8–
REV. A
AD9054A
–70
50
48
–68
fS = 200MSPS
fIN = 10.3MHz
SNR
–64
44
–62
SINAD
42
–60
dBc
SNR – dB
2ND HARMONIC
–66
46
40
3RD HARMONIC
–58
–56
38
–54
36
–52
34
–50
32
–48
30
0.0
0.5
1.0
1.5 2.0 2.5
3.0 3.5 4.0
ENCODE PULSEWIDTH – ns
4.5
–46
25
5.0
Figure 15. SNR vs. Clock Pulsewidth, (tPWH): f S = 200 MSPS
50
75
100 125 150 175 200 225 250
fS – MSPS
270 300
Figure 18. Harmonic Distortion vs. fS: fIN = 19.7 MHz
–60
46
45
2ND HARMONIC
–50
44
SINAD – dB
20MHz
–40
43
3RD HARMONIC
70MHz
42
–30
50MHz
41
–20
40
–10
39
38
–60
–40
–20
0
20
40
TC – 8C
60
80
0
25
100
50
75
100 125
150 175
200 225 250 270 300
fS – MSPS
Figure 16. SINAD vs. Temperature: fS = 135 MSPS
Figure 19. Harmonic Distortion vs. fS: fIN = 70.1 MHz
–40
46
45
–45
44
–50
50MHz
dB
SINAD – dB
20MHz
43
42
–55
70MHz
70MHz
41
–60
50MHz
40
–65
20MHz
39
38
–60
–40
–20
0
20
TC – 8C
40
60
80
–70
–60
100
–20
0
20
TC – 8C
40
60
80
100
Figure 20. 2nd Harmonic vs. Temperature: fS = 135 MSPS
Figure 17. SINAD vs. Temperature: fS = 200 MSPS
REV. A
–40
–9–
AD9054A
–40
0
–45
–1
–50
–2
dB
dB
70MHz
–55
–3
50MHz
–4
–60
NYQUIST FREQUENCY
100MHz
20MHz
–5
–65
–70
–60
–40
–20
0
20
TC – 8C
40
60
80
–6
100
0
Figure 21. 2nd Harmonic vs. Temperature: fS = 200 MSPS
50
100
150
200 250 300
fIN – MHz
350
400
450
500
Figure 24. Frequency Response: fS = 200 MSPS
–40
0
FUNDAMENTAL = –0.5dBFS
SNR = 45.8dB
SINAD = 45.2dB
2ND HARMONIC = 69.8dB
3RD HARMONIC = 61.6dB
–10
–45
–20
–50
–30
70MHz
–40
–55
dB
dB
50MHz
–50
20MHz
–60
–60
–70
–65
–80
–70
–60
–40
–20
0
20
TC – 8C
40
60
80
–90
0
100
Figure 22. 3rd Harmonic vs. Temperature: fS = 135 MSPS
10
20
30
40
50
60
MHz
70
80
90
100
Figure 25. Spectrum: fS = 200 MSPS, f IN = 19.7 MHz
–40
0
FUNDAMENTAL = –0.5dBFS
SNR = 44.6dB
SINAD = 37.6dB
2ND HARMONIC = –63.1dB
3RD HARMONIC = –39.1dB
–10
–45
–20
70MHz
–50
–30
–40
–55
dB
dB
50MHz
–50
20MHz
–60
–60
–70
–65
–80
–70
–60
–40
–20
0
20
TC – 8C
40
60
80
–90
100
0
Figure 23. 3rd Harmonic vs. Temperature: fS = 200 MSPS
10
20
30
40
50
MHz
60
70
80
90
100
Figure 26. Spectrum: f S = 200 MSPS, f IN = 70.1 MHz
–10–
REV. A
AD9054A
7
0
F1 = 55.0MHz
F2 = 56.0MHz
F1 = F2 = –7.0dBFS
–10
–20
tV
5
–30
–40
4
ns
dB
tPD
6
–50
3
–60
2
–70
–80
1
–90
0
–60
–100
0
10
20
30
40
50
MHz
60
70
80
90
100
5.0
2.55
4.5
2.54
4.0
2.53
3.5
2.52
VREF OUT – Volts
VOH – Volts
–20
0
20
TC – 8C
40
60
80
100
Figure 30. Output Delay vs. Temperature
Figure 27. Two-Tone Intermodulation Distortion
3.0
2.5
2.0
1.5
2.51
2.50
2.49
2.48
1.0
2.47
0.5
2.46
0.0
0.0
–40
2.45
–20 –18 –16
–1.0 –2.0 –3.0 –4.0 –5.0 –6.0 –7.0 –8.0 –9.0 –10.0
IOH – mA
–14 –12 –10 –8
–6
IREF OUT – mA
–4
–2
0
2
Figure 31. Reference Voltage vs. Reference Load
Figure 28. Output Voltage HIGH vs. Output Current
2.502
1.0
0.9
0.8
2.501
VREF OUT – Volts
VOL – Volts
0.7
0.6
0.5
0.4
0.3
2.500
2.499
0.2
0.1
0.0
0.0
1.0
2.0
3.0
4.0
5.0
IOL – mA
6.0
7.0
2.498
3.0
8.0
4.0
4.5
5.0
VDD – Volts
5.5
6.0
6.5
Figure 32. Reference Voltage vs. Power Supply Voltage
Figure 29. Output Voltage LOW vs. Output Current
REV. A
3.5
–11–
AD9054A
2.502
These applications require the converter to process inputs with
frequency components well in excess of the sampling rate (often
with subnanosecond rise times), after which the A/D must settle
and sample the input in well under one pixel time. The architecture of the AD9054A is vastly superior to older flash architectures, that not only exhibit excessive input capacitance (which is
very hard to drive), but can make major errors when fed a very
rapidly slewing signal. The AD9054A’s extremely wide bandwidth
Track/Hold circuit processes these signals without difficulty.
VREF OUT – Volts
2.501
2.500
2.499
2.498
–40
Using the AD9054A
–20
0
20
40
60
80
Good high speed design practices must be followed when using
the AD9054A. To obtain maximum benefit, decoupling capacitors should be physically as close to the chip as possible. We
recommend placing a 0.1 µF capacitor at each power-ground
pin pair (9 total) for high frequency decoupling, and including
one 10 µF capacitor for local low frequency decoupling. The
VREF IN pin should also be decoupled by a 0.1 µF capacitor.
100
TAMB – 8C
Figure 33. Reference Voltage vs. Temperature
APPLICATION NOTES
The part should be located on a solid ground plane and output
trace lengths should be short (<1 inch) to minimize transmission line effects. This avoids the need for termination resistors
on the output bus and reduces the load capacitance that needs
to be driven, which in turn minimizes on-chip noise due to
heavy current flow in the outputs. We have obtained optimum
performance on our evaluation board by tying all VDD pins to a
quiet analog power supply system, and tying all GND pins to a
quiet analog system ground.
THEORY OF OPERATION
The AD9054A combines Analog Devices’ patented MagAmp
bit-per-stage architecture with flash converter technology to
create a high performance, low power ADC. For ease of use
the part includes an onboard reference and input logic that
accepts TTL, CMOS or PECL levels.
The analog input signal is buffered by a high-speed differential
amplifier and applied to a track-and-hold (T/H) circuit. This
T/H captures the value of the input at the sampling instant and
maintains it for the duration of the conversion. The sampling
and conversion process is initiated by a rising edge on the
ENCODE input. Once the signal is captured by the T/H, the
four Most Significant Bits (MSBs) are sequentially encoded by
the MagAmp string. The residue signal is then encoded by a
flash comparator string to generate the four Least Significant
Bits (LSBs). The comparator outputs are decoded and combined into the 8-bit result.
Minimum Encode Rate
The minimum sampling rate for the AD9054A is 25 MHz.
To achieve very high sampling rates, the track/hold circuit employs a very small hold capacitor. When operated below the
minimum guaranteed sampling rate, the T/H droop becomes
excessive. This is first observed as an increase in offset voltage,
followed by degraded linearity at even lower frequencies.
If the user has selected Single Channel Mode (DEMUX =
HIGH), the 8-bit data word is directed to the Channel A output bank. Data are strobed to the output on the rising edge of
the ENCODE input with four pipeline delays. If the user has
selected Dual Channel Mode (DEMUX = LOW) the data are
alternately directed between the A and B output banks and have
five pipeline delays. At power-up, the N sample data can appear at either the A or B port. To align the data in a known
state the user must strobe DATA SYNC (DS, DS) per the
conditions described in the Timing section.
Graphics Applications
The high bandwidth and low power of the AD9054A make it
very attractive for applications that require the digitization of
presampled waveforms, wherein the input signal rapidly slews
from one level to another and is relatively stable for a period of
time. Examples of these include digitizing the output of computer graphic display systems and very high speed solid state
imagers.
Lower effective sampling rates may be easily supported by operating the converter in dual port output mode and using only
one output channel. A majority of the power dissipated by the
AD9054A is static (not related to conversion rate) so the penalty
for clocking at twice the desired rate is not high.
Reference
The AD9054A internal reference, VREF, provides a simple, cost
effective reference for many applications. It exhibits reasonable
accuracy and excellent stability over power supply and temperature variations. The VREF OUT pin can simply be strapped to
the VREF IN pin. The internal reference can be used to drive
additional loads (up to several mA), including multiple A/D converters as might be required in a triple video converter application.
When an external reference is desired for accuracy or other
requirements, the AD9054A should be driven directly by the
external reference source connected to pin VREF IN (VREF
OUT can be left floating). The external reference can be set to
2.5 V ± 0.25 V. If VREF IN is raised by 10% (set to 2.75 V) the
analog full-scale range will increase by 10% to 1.024 × 1.1 =
1.1264 V. The new input range will then be AIN ± 0.5632 V.
–12–
REV. A
AD9054A
Digital Inputs
When operating in Single-Channel Mode, the outputs at Port B
are held static in a random state.
SNR performance is directly related to the sampling clock stability in A/D converters, particularly for high input frequencies
and wide bandwidths. A low jitter clock (<10 ps @ 100 MHz)
is essential for optimum performance when digitizing signals
that are not presampled.
Figure 35 shows the AD9054A used in single-channel output
mode. The analog input (± 0.5 V) is ac coupled and the ENCODE
input is driven by a TTL level signal. The chip’s internal reference is used.
ENCODE and Data Select (DS) can be driven differentially or
single-ended. For single-ended operation, the complement
inputs (ENCODE, DS) are internally biased to VDD/3 (~1.5 V)
by a high impedance on-chip resistor divider (Figure 5), but
they may be externally driven to establish an alternate threshold
if desired. A 0.1 µF decoupling capacitor to ground is sufficient
to maintain a threshold appropriate for TTL or CMOS logic.
VREF OUT
0.1mF
VREF IN
CLOCK
ENC
+5V
ENC
0.1mF
CLOCK
NC = NO CONNECT
Figure 35. Single Port Mode—AC-Coupled Input—SingleEnded Encode
Dual Port Mode
In Dual Port Mode (DEMUX = LOW), the conversion results
are alternated between the two output ports (Figure 2). This
limits the data output rate at either port to 1/2 the conversion
rate (ENCODE), and supports conversion at up to 200 MSPS
with TTL/CMOS compatible interfaces. Dual Channel Mode is
required for guaranteed operation above 100 MSPS, but may be
enabled at any specified conversion rate.
VID
The multiplexing is controlled internally via a clock divider,
which introduces a degree of ambiguity in the port assignments.
Figure 2 illustrates that, prior to synchronization, either Port A
or Port B may produce the even or odd samples. This is resolved by exercising the Data Sync (DS) control, a differential
input (identical to the ENCODE input), which facilitates operation at high speed.
VIH D
VID
VIC M
VIL D
b. Driving Differential Inputs Single-Endedly
At least once after power-up, and prior to using the conversion
data, the part needs to be synchronized by a falling edge (or a
positive-going pulse) on DS (observing setup and hold times
with respect to ENCODE). If the converter’s internal timing is
in conflict with the DS signal when it is exercised, then two data
samples (one on each port) are corrupted as the converter is
resynchronized. The converter then produces data with a
known phase relationship from that point forward.
Figure 34. Input Signal Level Definitions
Single Port Mode
When operated in a Single Port mode (DEMUX = HIGH), the
timing of the AD9054A is similar to any high speed A/D Converter (Figure 1).
A sample is taken on every rising edge of ENCODE, and the
resulting data is produced on the output pins following the
FOURTH rising edge of ENCODE after the sample was taken
(four pipeline delays). The output data are valid tPD after the
rising edge of ENCODE, and remain valid until at least tV after
the next rising edge of ENCODE.
The maximum clock rate is specified as 100 MSPS. This is
recommended because the guaranteed output data valid time
equals the Clock Period (1/fS) minus the Output Propagation
Delay (tPD) plus the Output Valid Time (tV ), which comes to
4.8 ns at 100 MHz. This is about as fast as standard logic is able
to capture the data with reasonable design margins. The AD9054A
will operate faster in single-channel mode if you are able to
capture the data.
REV. A
ENC
0.1mF
a. Driving Differential Inputs Differentially
ENC
DS ENC
NC
VIL D
CLOCK
DEMUX
DS
VIH D
VIC M
AIN
0.1mF
Note the 6-diode clock input protection circuitry in Figure 5.
This limits the differential input voltage to ~ ± 2.1 V. When the
diodes turn on, current is limited by the 300 Ω series resistor.
Exceeding 2.1 V across the differential inputs will have no impact on the performance of the converter, but be aware of the
clock signal distortion that may be produced by the nonlinear
impedance at the converter.
ENC
AD9054A
1kV
VIN
When driven differentially, ENCODE and DS will accommodate differential signals centered between 1.5 V and 4.5 V with
a total differential swing ≥800 mV (VID ≥ 400 mV).
CLOCK
A PORT
AIN
Note that if the converter is already properly synchronized, the
DS pulse has no effect on the output data. This allows the converter to be continuously resynchronized by a pulse at 1/2 the
ENCODE rate. This signal is often available within a system, as
it represents the master clock rate for the demultiplexed output
data. Of course, a single DS signal may be used to synchronize
multiple A/D converters in a multichannel system.
–13–
AD9054A
Applications that call for the AD9054A to be synchronized at
power-up or only periodically during calibration/reset (i.e., valid
data is not required prior to synchronization), need only be
concerned with the timing of the falling edge of DS. The falling
edge of DS must satisfy the setup time defined by Figure 2 and
the specification table. In this case the DS hold time specification on the rising edge can be ignored.
In Dual Channel Mode, the converted data is produced five
clock cycles after the rising edge of ENCODE on which the
sample is taken (five pipeline delays).
Applications that will continuously update the synchronization
command need to treat the DS signal as a pulse and satisfy
timing requirements on both rising and falling edges. It is easiest
to consider the DS signal in this case to be a pulse train at one
half the encode rate, the positive pulse nominally bracketing the
ENCODE falling edge on alternate cycles as shown in the timing diagram (Figure 2b). The falling/rising edge of DS has to
satisfy a minimum setup time (tSDS ) before the rising/falling
edge of ENCODE; similarly, the rising/falling edge of DS has to
satisfy a minimum hold time (tHDS ) relative to the rising/falling
edge of ENCODE. DS can fall a minimum of tHDS after
ENCODE falls and a maximum of tSDS before the next
ENCODE rises. DS can rise a minimum of tHDS after
ENCODE rises and a maximum of tSDS before ENCODE falls.
This timing requirement produces a tight timing window at
higher encode rates. Synchronization by a single reset edge
results in a simpler timing solution in many applications. For
example, synchronization may be provided at the beginning of
each graphics line or frame.
In Figure 36, the converter is operating in Dual Port Mode,
with data coming alternately out of Port A and Port B. The
figure illustrates how the output data may be aligned with an
output latch to produce a 16-bit output at 1/2 the conversion
clock rate. The Data Sync input must be properly exercised to
time the A Port with the synchronizing latch.
VREF OUT
0.1mF
VREF IN
A PORT
AIN
'573
AD9054A
1kV
AIN
VIN
0.1mF
B PORT
DEMUX
DS
DS ENC
ENC
0.1mF
DS
NC
CLOCK
'74
The data are presented at the output of the AD9054A in a pingpong (alternating) fashion to optimize the performance of the
converter. It may be aligned for presentation as sixteen bits in
parallel by adding a register stage to the output.
DIVIDE
BY 2
NC = NO CONNECT
Figure 36. Dual Port Mode—Aligned Output Data
–14–
REV. A
AD9054A
EVALUATION BOARD
Voltage Reference
The AD9054A evaluation board offers an easy way to test the
AD9054A. It provides dc biasing for the analog input, generates
the latch clocks for both full speed and demuxed modes, and includes a reconstruction DAC. The board has several different
modes of operation, and is shipped in the following configuration:
The AD9054A has an internal 2.5 V voltage reference. An
external reference may be employed instead. The evaluation
board is configured for the internal reference. To use an external reference, connect it to the (VREF) pin on the power connector and move jumper S102.
•
•
•
•
Single Port Mode
DC-Coupled Analog Input
Demuxed Outputs
Differential Clocks
Internal Voltage Reference.
VREF EXT
DC BIAS
AIN
Single Port Mode sets the AD9054A to produce data on every
clock cycle on output port A only. To test in this mode, jumper
S104 should be set to single channel and S106 and S107 must
be set to F (for Full). The maximum speed in single port mode
is 100 MSPS.
S102
S103
Dual Port Mode
VREF OUT
Dual Port or half speed output mode sets the ADC to produce
data alternately on Port A and Port B. In this mode, the reset
function should be implemented. To test in this mode, set
jumper S104 to Dual Channel, and set S106 and S107 to D (for
Dual Port). The maximum speed in this mode is 200 MSPS.
B PORT
VREF IN
'574
50V
AIN
AD9054A
AIN
RESET
BUTTON
A PORT
5V
RESET
'574
RESET drives the AD9054A’s Data Sync (DS) pins. When
operating in Single Port Mode, RESET is not used. In DualChannel Mode it is needed for two reasons: to synchronize the
timing of Port A data and Port B data with a known clock edge,
as described in the data sheet, and to synchronize the evaluation
board’s latch clocks with the data coming out of the AD9054A.
Reset can be driven in two ways: by pushing the reset button on
the board, or externally, with a TTL pulse through connector J5
or J6.
DEMUX
D
D FF
S104
C
S105
CLK A
DS DS ENC ENC
CLK B
DAC
ENC
50V
ENC
ENC
CLK A
DAC Out
ENC CLOCKING CLK B
The DAC output is a representation of the data on output Port
A only. Output Port B is not reconstructed.
50V
Troubleshooting
Figure 37. PCB Block Diagram
If the board does not seem to be working correctly, try the following:
Analog Input
• Check that all jumpers are in the correct position for the
desired mode of operation.
The evaluation board accepts a 1 V input signal centered at
ground. The board’s input circuitry then biases this signal to
+2.5 V in one of two ways:
1. DC-coupled through an AD9631 op amp; this is the mode in
which it is shipped. Potentiometer R7 provides adjustment
of the bias voltage.
2. AC-coupled through C1.
These two modes are selected by jumpers S101 and S103. For
dc coupling, the S101 jumper is connected between the two left
pins and the S103 jumper is connected between the two lower
pins. For ac coupling, the S101 jumper is connected between
the two right pins and the S103 jumper is connected between
the two upper pins.
ENCODE
The AD9054A ENCODE input can be driven two ways:
1. Differential TTL, CMOS, or PECL; it is shipped in this
mode.
• Push the reset button. This will align the AD9054A’s data
output with the half speed latch clocks.
• Switch the jumper S105 from A-R to R-B or vice-versa, then
push the reset button. In demuxed mode, this will have the
effect of inverting the half speed latch clocks.
• At high encode rates, the evaluation board’s clock generation
circuitry is sensitive to the +5 V digital power supply. At
high encode rates, the +5 V digital power should be kept
below +5.2 V. This is an evaluation board sensitivity and
not an AD9054A sensitivity.
The AD9054A Evaluation Board is provided as a design example for customers of Analog Devices, Inc. ADI makes no
warranties, express, statutory, or implied, regarding merchantability or fitness for a particular purpose.
2. Single-ended TTL or CMOS. To use in this mode, remove
R11, the 50 Ω chip resistor located next to the ENCODE
input, and insert a 0.1 µF ceramic capacitor into the C5 slot.
C5 is located between the ENC connector and the ENCODE
input to the DUT and is marked on the back side of the
board. In this mode, ENCODE is biased with internal resistors to 1.5 V, but it can be externally driven to any dc voltage.
REV. A
–15–
+5VA
+5V
ENC
ENC
R1
49.9V
2
C23
10mF
C9
10mF
BNC
J3
C4
0.1mF
C24
0.1mF
C10
0.1mF
C25
0.1mF
C11
0.1mF
R4
140V
R5
10V
3
2
Q
4
+5V
C Q
CL
1
D
PR
+5V
TB1
4
3
C26
0.1mF
11
C27
0.1mF
C13
0.1mF
+5V
GND
–5.2V
+5VA
VREF
6
12
2
C29
0.1mF
C14
0.1mF
GND
+5VA
GND
+5VA
GND
1
3
–5.2V
U6
10H131
GND
1
C30
10mF
C5
1
3
C31
0.1mF
C17
0.1mF
Q1
3
R1
4
UA1
AD9054ABST
2
23
22
21
20
19
18
17
16
15
14
13
12
12
5
10H125
U7
10H125
U7
4
+5VA
GND
GND
+5VA
15
C21
0.1mF
10H125
14 U7
13
10H125
U7
10
11
6
7
2
3
1
C34
0.1mF
C20
0.1mF
2
3
S105
JUMPER
11
DB3
DB2
DB1
(LSB) DB0
VDD
GND
GND
VDD
(LSB) DA0
DA1
DA2
C33
0.1mF
C19
0.1mF
1
3
S107
JUMPER
C32
0.1mF
C18
0.1mF
2
S106
JUMPER
ENC ENC
VREF
OUT
VREF IN
GND
VDD
GND
AIN
AIN
GND
VDD
DEMUX
DS
DS
33
C3
10mF
S1
2
D1 Q1
C16
0.1mF
6
7
5
34
35
36
37
38
39
40
41
42
43
44
1 2 3 4 5 6
5PB 510
RP1
2
C15
0.1mF
1
3
S104
JUMPER
–5.2V
+5VA
GND
R9
100V
1
3
U2
74F74
6
5
AD96685R
U3
C12
0.1mF
5
4
3
2
1
R12
1kV
GND
VREF
+5V ANALOG
–5.2V
GROUND
+5V DIGITAL
R11
49.9V
R10
49.9V
C1
0.1mF
2
6
C36, C37, AND R17–R20
NOT INSTALLED FOR
STANDARD OPERATION
140V
RST
+5V
1
3
S101
JUMPER R2
B1
BUTTON
BNC
J2
+5V
AIN
BNC
J1
3
S103
JUMPER
2
GND
+5VA
+5VA
GND
+5VA
GND
GND
VDD
VDD
GND
VDD
GND
VDD
GND
VDD
GND
+5VA
GND
+5VA
GND
U1
AD9631R
DB7
DB6
DB5
DB4
DA7
DA6
DA5
DA4
DA3
C35
0.1mF
C22
0.1mF
1
1Q
2Q
3Q
4Q
5Q
6Q
7Q
8Q
OE
12
13
14
15
16
17
18
19
11
1D
2D
3D
4D
5D
6D
7D
8D
CK
+5V
28
1
1Q
2Q
3Q
4Q
5Q
6Q
7Q
8Q
OE
RST
GND
1 2 3 4 5 6 7 8 9 10
CLK
12
13
14
15
16
17
18
19
U5
74F574DW
11
1D
2D
3D
4D
5D
6D
7D
8D
CK
C28
0.1mF
9
8
7
6
5
4
3
2
9
8
7
6
5
4
3
2
U4
74F574DW
U8
AD9760AR
C6
0.1mF
+5V
C8
0.1mF
17 16 15
R14
2kV
18
C7
0.1mF
27 24 23 19
DVDD
VREF
AVDD
S102
JUMPER
COMP2
C2
0.1mF
COMP1
R3
100V
FSADJ
R8
2kV
REFIO
R7
1kV
DB9
DB8
DB7
DB6
DB5
DB4
DB3
DB2
DB1
DB0
(LSB)
REFLO
–16–
SLEEP
R6
2kV
A
I OUT
B
3
13
14
15
16
17
18
19
20
22
21
R15
49.9V
R16
49.9V
21
30
31
32
33
34
35
36
37
2
2
BNC
J4
DRA
B8A
B7A
B6A
B5A
B4A
B3A
B2A
B1A
DRB
B1B
B2B
B3B
B4B
B5B
B6B
B7B
B8B
DAC
OUT
RESET
C37 DRPF
J6
20
29
28
27
26
25
24
23
22
R39
R21
R21–R39
100V
11
10
9
8
7
6
5
4
1
12
H20SM
J5
AD9054A
Figure 38. Evaluation Board Schematic
REV. A
AD9054A
REV. A
Figure 39. Assembly—Top View
Figure 41. Conductors—Top View
Figure 40. Assembly—Bottom View
Figure 42. Conductors—Bottom View
–17–
AD9054A
BILL OF MATERIALS
GS00104 REV. B
ITEM
QTY
PART NUMBER
REFERENCE
DESCRIPTION
MFG/DISTRIBUTOR
11
30
GRM40Z5U104M050BL
C1, C2, C4, C6–8,
C10–C22, C24–C29,
C31–C35
0.1 µF CER CHIP CAP 0805
TTI
12
1
P10FBK-ND
R5
10 Ω SURFACE MT RES 1206
DIGI-KEY
13
21
P100FBK-ND
R3, R9, R21–R39
100 Ω SURFACE MT RES 1206
DIGI-KEY
14
4
T491C106M016AS
C3, C9, C23, C30
10 µF TANTALUM CHIP CAP
TTI
15
2
P140FBK-ND
R2, R4
140 Ω SURFACE MT RES 1206
DIGI-KEY
16
1
P1KFBK-ND
R12
1 kΩ SURFACE MT RES 1206
DIGI-KEY
17
3
P2KFBK-ND
R6, R8, R14
2 kΩ SURFACE MT RES 1206
DIGI-KEY
18
1
3296W-102-ND
R7
1k TRIM POT TOP ADJ, 25 TURN
DIGI-KEY
19
1
K44-C37S-QJ
J6
37P D CONN RT ANG PCMT FEM
CENTURY ELEC
10
5
P49.9FBK-ND
R1, R10, R11,
R15, R16
49.9 Ω SURFACE MT RES 1206
DIGI-KEY
11
1
CSC06A-01-511G
RP1
510 Ω 6P BUSED RES NETWORK
TTI
12
1
51F54113
TB1
8291Z 3-PIN TERMINAL BLOCK
NEWARK
13
1
51F54112
TB1
8291Z 2-PIN TERMINAL BLOCK
NEWARK
14
4
AMP-227699-2
J1–J4
BNC COAX CONN PCMT 5 LEAD
TIME ELEC
15
1
MC10H131P
U6
DIP-16 DUAL D FLIP-FLOP
HAMILTON/HALLMARK
16
1
MC10H125P
U7
DIP-16 QUAD ECL TO TTL TRANS
HAMILTON/HALLMARK
17
1
74F74SC-ND
U2
SO-14 FAST TTL DUAL D FLIP-FLOP
DIGI-KEY
18
1
TSW-120-08-G-S
J5
HEADER STRIP 20P GOLD MALE
SAMTEC
ALT:
1/2
90F3987
J5
40P HEADER
NEWARK
19
1
AD96685BR
U3
HIGH SPEED COMP SOIC-16
ANALOG DEVICES, INC.
20
7
S90F9280
S101–S107
SHORTING JUMPER
NEWARK
21
8
89F4700
S101–S107, GND
3-PIN HEADER (DIVIDE 1 OF THE
8 FOR 3 GND HOLES)
NEWARK
22
2
MC74F574DW
U4, U5
SO-20 OCTAL D TYPE FLIP-FLOP
HAMILTON/HALLMARK
23
1
AD9631AR
U1
SOIC-8 OP AMP
ANALOG DEVICES, INC.
24
1
AD9760AR
U8
10-BIT CMOS DAC SOIC-28
ANALOG DEVICES, INC.
25
1
AD9054ABST
UA1
8-BIT ADC IN 44-LEAD LQFP
ANALOG DEVICES, INC.
26
1
P8002SCT-ND
B1
SURFACE MOUNT MOMENTARY
PUSHBUTTON
DIGI-KEY
27
4
90F1533
–
BUMPON PROTECTIVE BUMPER
NEWARK
PARTS NOT ON BILL OF MATERIALS, AND NOT TO BE INSTALLED: C5, C36, C37, R17–R20.
–18–
REV. A
AD9054A
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
0.063 (1.60)
MAX
0.472 (12.00) SQ
0.030 (0.75)
0.018 (0.45)
23
33
34
22
SEATING
PLANE
0.394
(10.0)
SQ
TOP VIEW
(PINS DOWN)
44
12
1
0.006 (0.15)
0.002 (0.05)
0.031 (0.80)
BSC
11
0.018 (0.45)
0.012 (0.30)
PRINTED IN U.S.A.
0.057 (1.45)
0.053 (1.35)
C3478–0–1/00 (rev. A)
44-Lead Plastic Thin Quad Flatpack (LQFP)
(ST-44)
REV. A
–19–