MAXIM MAX5952CEAX+

19-0858; Rev 1; 1/10
KIT
ATION
EVALU
E
L
B
AVAILA
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
The MAX5952 is a quad -48V power controller
designed for use in IEEE® 802.3af-compliant/pre-IEEE
802.3at-compatible power-sourcing equipment (PSE).
This device provides powered device (PD) discovery,
classification, current limit, DC and AC load disconnect
detections in compliance with the IEEE 802.3af standard. The MAX5952 is pin compatible with MAX5945/
LTC4258/LTC4259A PSE controllers and provides additional features.
The MAX5952 features high-power mode that provides
up to 45W per port. The MAX5952 provides instantaneous readout of each port current through the I2C interface. The MAX5952 also provides high-capacitance
detection for legacy PDs.
The device features an I2C-compatible, 3-wire serial interface, and is fully software configurable and programmable. The class-overcurrent detection function enables
system power management to detect if a PD draws more
than the allowable current. The MAX5952’s extensive programmability enhances system flexibility, enables field
diagnosis, and allows for uses in other applications.
The MAX5952 provides four operating modes to suit different system requirements. Auto mode allows the device
to operate automatically without any software supervision.
Semi-automatic mode automatically detects and classifies a device connected to a port after initial software activation, but does not power up that port until instructed to
by software. Manual mode allows total software control of
the device and is useful for system diagnostics.
Shutdown mode terminates all activities and securely
turns off power to the ports.
The MAX5952 provides input undervoltage lockout
(UVLO), input undervoltage detection, input overvoltage lockout, overtemperature detection, output voltage
slew-rate limit during startup, power-good status, and
fault status. The MAX5952’s programmability includes
startup timeout, overcurrent timeout, and load-disconnect detection timeout.
Features
o IEEE 802.3af Compliant/Pre-IEEE 802.3at
Compatible
o Instantaneous Readout of Port Current Through
I2C Interface
o High-Power Mode Enables Up to 45W Per Port
o High-Capacitance Detection for Legacy Devices
o Pin Compatible to MAX5945 and
LTC4258/LTC4259A
o Four Independent Power-Switch Controllers
o PD Detection and Classification
o Supports Both DC and AC Load Removal
Detections
o I2C-Compatible, 3-Wire Serial Interface
o Current Foldback and Duty-Cycle-Controlled
Current Limit
o Open-Drain INT Signal
o Direct Fast Shutdown Control Capability
Ordering Information
TEMP RANGE
PIN-PACKAGE
MAX5952AEAX+*
PART
-40°C to +85°C
36 SSOP
MAX5952AUAX+
0°C to +85°C
36 SSOP
MAX5952CEAX+*
-40°C to +85°C
36 SSOP
MAX5952CUAX+*
0°C to +85°C
36 SSOP
+Denotes a lead(Pb)-free/RoHS-compliant package.
*Future product—contact factory for availability.
The MAX5952 is available in a 36-pin SSOP package and
is rated for both extended (-40°C to +85°C) and upper
commercial (0°C to +85°C) temperature ranges.
Applications
Power-Sourcing Equipment (PSE)
Switches/Routers
Midspan Power Injectors
Pin Configuration and Selector Guide appear at end of data
sheet.
IEEE is a registered service mark of the Institute of Electrical
and Electronics Engineers, Inc.
________________________________________________________________ Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.
1
MAX5952
General Description
MAX5952
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
ABSOLUTE MAXIMUM RATINGS
(Voltages referenced to VEE, unless otherwise noted.)
AGND, DGND, DET_, VDD, RESET, A3–A0, SHD_, OSC,
SCL, SDAIN, and AUTO ......................................-0.3V to +80V
OUT_........................................................-12V to (AGND + 0.3V)
GATE_ (internally clamped) (Note 1) ..................-0.3V to +11.4V
SENSE_ ..................................................................-0.3V to +24V
VDD, RESET, MIDSPAN, A3–A0, SHD_, OSC, SCL,
SDAIN and AUTO to DGND ..................................-0.3V to +7V
INT and SDAOUT to DGND....................................-0.3V to +12V
AGND to DGND........................................................-0.3V to +7V
Maximum Current into INT, SDAOUT, DET_ .......................80mA
Maximum Power Dissipation (TA = +70°C)
36-Pin SSOP (derate 11.4mW/°C above +70°C) ..........941mW
Operating Temperature Ranges:
MAX5952_EAX..............…………………………-40°C to +85°C
MAX5952_UAX ....................................................0°C to +85°C
Storage Temperature Range .............................-65°C to +150°C
Junction Temperature ......................................................+150°C
Lead Temperature (soldering, 10s) .................................+300°C
Note 1: GATE_ is internally clamped to 11.4V above VEE. Driving GATE_ higher than 11.4V above VEE may damage the device.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(VAGND = 32V to 60V, VEE = 0V, VDD to VDGND = +3.3V, all voltages are referenced to VEE, unless otherwise noted. Typical values are at
VAGND = +48V, VDGND = +48V, VDD = (VDGND + 3.3V), TA = +25°C. Currents are positive when entering the pin and negative otherwise.) (Note 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
POWER SUPPLIES
VAGND
Operating Voltage Range
VDD
Supply Currents
VAGND - VEE
32
60
0
60
VDD to VDGND, VDGND = VAGND
1.71
5.50
VDD to VDGND, VDGND = VEE
3.0
5.5
VDGND
IEE
VOUT_ = VEE, VSENSE_ = VEE, DET_ = AGND,
all logic inputs open, SCL = SDAIN = VDD.
INT and SDAOUT open. Measured at AGND in
power mode after GATE_ pullup
4.8
6.8
IDIG
All logic inputs high, measured at VDD
3.0
5.6
IPU
V
mA
GATE DRIVER AND CLAMPING
GATE_ Pullup Current
Power mode, gate drive on, VGATE = VEE
-40
-50
-60
µA
Weak GATE_ Pulldown Current
IPDW
SHD_ = DGND, VGATE_ = VEE + 10V
30
42
55
µA
Maximum Pulldown Current
IPDS
VSENSE = 600mV, VGATE_ = VEE + 2V
External Gate Drive
VGS
VGATE - VEE, power mode, gate drive on
9
10
2
70
_______________________________________________________________________________________
mA
11
V
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
(VAGND = 32V to 60V, VEE = 0V, VDD to VDGND = +3.3V, all voltages are referenced to VEE, unless otherwise noted. Typical values are at
VAGND = +48V, VDGND = +48V, VDD = (VDGND + 3.3V), TA = +25°C. Currents are positive when entering the pin and negative otherwise.) (Note 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
IVEE = 00
202
212
220
IVEE = 01
192
202
212
IVEE = 10
186
190
200
IVEE = 11
170
180
190
ICUT = 000
(Class 0/3)
177
186
196
ICUT =110
(Class 1)
47
55
62
ICUT = 111
(Class 2)
86
94
101
ICUT = 001
265
280
295
ICUT = 010
310
327
345
ICUT = 011
355
374
395
ICUT = 100
398
419
440
ICUT =101
443
466
488
UNITS
CURRENT LIMIT
Current-Limit Clamp Voltage
Overcurrent Threshold After
Startup
Foldback Initial OUT_ Voltage
Foldback Final OUT_ Voltage
Minimum Foldback
Current-Limit Threshold
SENSE_ Input Bias Current
VSU_LIM
VFLT_LIM
VFLBK_ST
Maximum VSENSE_ allowed
during current limit, VOUT_ = 0V
(ICUT = 000) (Note 3)
Overcurrent VSENSE_ threshold
allowed for t ≤ tFAULT after
startup; VOUT_ = 0V,
(IVEE = 00)
VOUT_ - VEE, above which the
current-limit trip voltage starts
folding back, IVEE = 00
mV
mV
ICUT = 000,
ICUT = 110,
ICUT = 111
28
ICUT =
001…101
10
V
IVEE = 00, ICUT = 000, VOUT - VEE above
VFLBK_END which the current-limit trip voltage reaches
VTH_FB
VTH_FB
VOUT_ = VAGND = 60V, IVEE = 00, ICUT = 000
VSENSE_ = VEE
-2
50
V
64
mV
+2
µA
_______________________________________________________________________________________
3
MAX5952
ELECTRICAL CHARACTERISTICS (continued)
MAX5952
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
ELECTRICAL CHARACTERISTICS (continued)
(VAGND = 32V to 60V, VEE = 0V, VDD to VDGND = +3.3V, all voltages are referenced to VEE, unless otherwise noted. Typical values are at
VAGND = +48V, VDGND = +48V, VDD = (VDGND + 3.3V), TA = +25°C. Currents are positive when entering the pin and negative otherwise.) (Note 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
SUPPLY MONITORS
VEE Undervoltage Lockout
VEE Undervoltage Lockout
Hysteresis
VEEUVLO
VEEUVLOH
VEE Overvoltage Lockout
VEE_OV
VEE Overvoltage Lockout
Hysteresis
VOVH
VAGND - VEE, VAGND - VEE increasing
Ports shut down if VAGND - VEE < VUVLO VEEUVLOH
VEE_OV event bit sets and ports shut down if
VAGND - VEE > VEE_OV, VAGND increasing
VEE Undervoltage
VEE_UV
VEE_UV event bit is set if VAGND - VEE < VEE_UV,
VEE increasing
VDD Overvoltage
VDD_OV
VDD_OV event bit is set if
VDD - VDGND > VDD_OV;
VDD increasing
VDD Undervoltage
VDD_UV
VDD Undervoltage Lockout
VDDUVLO
VDD Undervoltage Lockout
Hysteresis
VDDHYS
VDD_OV is set if VDD - VDGND
> VDD_UV, VDD decreasing
28.5
V
3
V
62.5
V
1
V
40
V
MAX5952A
3.82
MAX5952C
5.7
MAX5952A
2.7
MAX5952C
4.2
V
V
Device operates when VDD - VDGND >
VDDUVLO, VDD increasing
2
V
120
mV
Ports shut down and device resets if its
junction temperature exceeds this limit,
temperature increasing (Note 4)
150
°C
20
°C
Thermal Shutdown Threshold
TSHD
Thermal Shutdown Hysteresis
TSHDH
Thermal hysteresis, temperature decreasing
(Note 5)
IBOUT
VOUT = VAGND, all modes
OUTPUT MONITOR
OUT_ Input Current
Idle Pullup Current at OUT_
IDIS
PGOOD High Threshold
PGTH
PGOOD Hysteresis
PGHYS
PGOOD Low-to-High Glitch
Filter
tPGOOD
4
OUT_ discharge current, detection and
classification off, port shutdown,
VOUT_ = VAGND - 2.8V
200
VOUT_ - VEE, OUT_ decreasing
1.5
Minimum time PGOOD has to be high to set
bit in register 10h
2.0
2
µA
260
µA
2.5
V
220
mV
3
ms
_______________________________________________________________________________________
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
(VAGND = 32V to 60V, VEE = 0V, VDD to VDGND = +3.3V, all voltages are referenced to VEE, unless otherwise noted. Typical values are at
VAGND = +48V, VDGND = +48V, VDD = (VDGND + 3.3V), TA = +25°C. Currents are positive when entering the pin and negative otherwise.) (Note 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
LOAD DISCONNECT
DC Load Disconnect
Threshold
VDCTH
Minimum VSENSE allowed before disconnect
(DC disconnect active), VOUT_ = 0V
2.5
3.75
5.0
mV
AC Load Disconnect
Threshold (Note 6)
IACTH
Current into DET_, for I < IACTH the port
powers off, ACD_EN_ bit = H; VOSC_IN = 2.2V
300
320
350
µA
Oscillator Buffer Gain
AOSC
VDET_/VOSC, ACD_EN_ bit = H
2.9
3.0
3.1
V/V
VOSC_FAIL
Port does not power on if VOSC < VOSC_FAIL
and ACD_EN_ bit is high
1.8
2.2
V
OSC Input Impedance
ZOSC
OSC input impedance when all the ACD_EN_
are active
100
Load Disconnect Timer
tDISC
Time from VSENSE < VDCTH to gate shutdown
(Note 8)
300
Detection Probe Voltage
(First Phase)
VDPH1
VAGND - VDET_ during the first detection
phase
3.8
Detection Probe Voltage
(Second Phase)
VDPH2
VAGND - VDET_ during the second detection
phase
Current-Limit Protection
IDLIM
VDET_ = VAGND, during detection, measure
current through DET_
Short-Circuit Threshold
VDCP
If VAGND - VOUT < VDCP after the first
detection phase a short circuit to AGND is
detected
Open-Circuit Threshold
ID_OPEN
OSC Fail Threshold (Note 7)
kΩ
400
ms
4
4.2
V
9.0
9.3
9.6
V
1.5
1.75
2.0
mA
DETECTION
Resistor Detection Window
Resistor Rejection Window
RDOK
RDBAD
First point measurement current threshold for
open condition
(Note 9)
1
V
12.5
µA
19.0
26.5
Detection rejects lower values
15.2
kΩ
kΩ
Detection rejects higher values
32
VAGND - VDET_ during classification
16
20
V
DET_ = AGND, during classification, measure
current through DET_
68
81
mA
CLASSIFICATION
Classification Probe Voltage
Current-Limit Protection
Classification Current
Thresholds
VCL
ICILIM
ICL
Classification current
thresholds between
classes
Class 0, Class 1
5.5
6.5
7.5
Class 1, Class 2
13
14.5
16
Class 2, Class 3
21
23
25
Class 3, Class 4
31
33
35
Class 4, Class 5
45
48
51
mA
_______________________________________________________________________________________
5
MAX5952
ELECTRICAL CHARACTERISTICS (continued)
MAX5952
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
ELECTRICAL CHARACTERISTICS (continued)
(VAGND = 32V to 60V, VEE = 0V, VDD to VDGND = +3.3V, all voltages are referenced to VEE, unless otherwise noted. Typical values are at
VAGND = +48V, VDGND = +48V, VDD = (VDGND + 3.3V), TA = +25°C. Currents are positive when entering the pin and negative otherwise.) (Note 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
0.9
V
DIGITAL INPUTS/OUTPUTS (Referred to DGND)
Digital Input Low
VIL
Digital Input High
VIH
2.4
V
Internal Input Pullup/Pulldown
Resistor
RDIN
Pullup (pulldown) resistor to VDD (DGND) to
set default level
Open-Drain Output Low Voltage
VOL
ISINK = 15mA
0.4
V
Digital Input Leakage
IDL
Input connected to the pull voltage
2
µA
Open-Drain Leakage
IOL
Open-drain high impedance, VO = 3.3V
2
µA
25
50
75
kΩ
TIMING
Startup Time
tSTART
Time during which a current limit set by
VSU_LIM is allowed, starts when the GATE_ is
turned on (Note 5)
50
60
70
ms
Fault Time
tFAULT
Maximum allowed time for an overcurrent
condition set by VFLT_LIM after startup (Note 5)
50
60
70
ms
Port Turn-Off Time
tOFF
Detection Reset Time
Detection Time
tDET
Midspan Mode Detection Delay
tDMID
Classification Time
tCLASS
VEEUVLO Turn-On Delay
Restart Timer
tDLY
tRESTART
Minimum delay between any port turning off,
does not apply in case of a reset
0.5
Time allowed for the port voltage to reset
before detection starts
80
Maximum time allowed before detection is
completed
2.0
Time allowed for classification
Time VAGND must be above the VEEUVLO
thresholds before the device operates
Time a port has to wait
before turning on after an
overcurrent fault,
RSTR_EN_ bits = high
tWD
2
RSTR bits = 00
16 x
tFAULT
RSTR bits = 01
32 x
tFAULT
RSTR bits = 10
RSTR bits = 11
Watchdog Clock Period
19
Rate of decrement of the watchdog timer
ms
90
ms
330
ms
2.4
s
23
ms
4
ms
ms
64 x
tFAULT
0
164
ms
9
Bits
ADC PERFORMANCE
Resolution
Range
LSB Step Size
Integral Nonlinearity (Relative)
6
INL
0.51
V
1
mV
0.5
LSB
_______________________________________________________________________________________
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
(VAGND = 32V to 60V, VEE = 0V, VDD to VDGND = +3.3V, all voltages are referenced to VEE, unless otherwise noted. Typical values are at
VAGND = +48V, VDGND = +48V, VDD = (VDGND + 3.3V), TA = +25°C. Currents are positive when entering the pin and negative otherwise.) (Note 2)
PARAMETER
Differential Nonlinearity
SYMBOL
CONDITIONS
MIN
DNL
ADC Absolute Accuracy
TYP
MAX
0.1
UNITS
LSB
VSENSE = 100mV
5B
(91)
62
(98)
68
(104)
VSENSE = 250mV
F0
(240)
FC
(252)
108
(264)
VSENSE = 400mV
186
(390)
196
(406)
1A6
(422)
Hex
(Dec)
TIMING CHARACTERISTICS (For 2-Wire Fast Mode, Note 10)
Serial-Clock Frequency
fSCL
Bus Free Time Between a
STOP and START Condition
tBUF
1.2
µs
tHD, STA
0.6
µs
Low Period of the SCL Clock
tLOW
1.2
µs
High Period of the SCL Clock
tHIGH
0.6
µs
Setup Time for a Repeated
START Condition (Sr)
tSU, STA
0.6
µs
Data Hold Time
tHD, DAT
0
Data in Setup Time
Hold Time for a START
Condition
400
150
kHz
ns
tSU, DAT
100
Rise Time of Both SDA and
SCL Signals, Receiving
tR
20 +
0.1CB
ns
300
ns
Fall Time of SDA Transmitting
tF
20 +
0.1CB
300
ns
Setup Time for STOP Condition
tSU, STO
0.6
Capacitive Load for Each Bus
Line
CB
400
pF
Pulse Width of Spike
Suppressed
tSP
50
ns
µs
Limits to TA = -40°C are guaranteed by design.
Default values. The current-limit thresholds are programmed through the I2C-compatible serial interface (see the Register
Map and Description section).
Note 4: Functional test is performed over thermal shutdown entering test mode.
Note 5: Default values. The startup and fault times can be also programmed through the I2C serial interface (see the Register Map
and Description section).
Note 6: This is the default value. Threshold can be programmed through serial interface R23h[2:0].
Note 7: AC disconnect works only if (VDD - VDGND) ≥ 3V and DGND is connected to AGND.
Note 8: tDISC can also be programmed through the serial interface (R16H) (see the Register Map and Description section).
Note 9: RD = (VOUT_2 - VOUT_1) / (IDET_2 - IDET_1). VOUT_1, VOUT_2, IDET_2 and IDET_1 represent the voltage at OUT_ and the current at DET_ during phase 1 and 2 of the detection.
Note 10: Guaranteed by design. Not subject to production testing.
Note 2:
Note 3:
_______________________________________________________________________________________
7
MAX5952
ELECTRICAL CHARACTERISTICS (continued)
Typical Operating Characteristics
(VEE = -48V, VDD = +3.3V, VAUTO = VAGND = VDGND = 0V, RESET = SHD_ = unconnected, RSENSE = 0.5Ω, IVEE = 00, ICUT = 000,
TA = +25°C, all registers = default setting, unless otherwise noted.)
4.9
4.8
4.7
4.6
5.0
4.0
4.9
4.8
4.7
4.6
3.5
3.0
2.5
2.0
1.5
4.5
4.5
1.0
4.4
4.4
0.5
4.3
4.3
37
42
47
52
57
0
-40
62
-15
10
35
60
-40
85
10
35
60
TEMPERATURE (°C)
TEMPERATURE (°C)
DIGITAL SUPPLY CURRENT
vs. DIGITAL SUPPLY VOLTAGE
VEE UNDERVOLTAGE LOCKOUT
vs. TEMPERATURE
GATE OVERDRIVE
vs. INPUT VOLTAGE
5
4
3
2
30.0
29.5
29.0
28.5
28.0
27.5
1
27.0
0
2.2
2.6
3.0
3.4
3.8
4.2
4.6
-40
5.0
-15
10
35
60
9.48
9.46
9.44
9.42
9.40
9.38
9.36
9.34
9.32
9.30
9.28
9.26
9.24
9.22
9.20
85
32
37
42
47
52
SUPPLY VOLTAGE (V)
TEMPERATURE (°C)
INPUT VOLTAGE (V)
GATE OVERDRIVE vs. TEMPERATURE
SENSE TRIP VOLTAGE
vs. TEMPERATURE
SENSE TRIP VOLTAGE
vs. INPUT VOLTAGE
10.0
9.5
9.0
8.5
8.0
190
185
180
62
57
62
MAX5952 toc09
189
188
187
186
185
184
183
182
175
7.5
57
190
SENSE TRIP VOLTAGE (mV)
195
SENSE TRIP VOLTAGE (mV)
10.5
MAX5952 toc08
200
MAX5952 toc07
11.0
85
MAX5952 toc06
MEASURED AT VDD
GATE OVERDRIVE (V)
MAX5952 toc04
6
1.8
-15
INPUT VOLTAGE (V)
MAX5952 toc05
32
181
7.0
170
-40
-15
10
35
TEMPERATURE (°C)
8
4.5
SUPPLY CURRENT (mA)
SUPPLY CURRENT (mA)
5.1
MAX5952 toc03
5.2
UNDERVOLTAGE LOCKOUT (V)
SUPPLY CURRENT (mA)
5.0
5.0
MAX5952 toc02
MEASURED AT AGND
5.1
SUPPLY CURRENT (mA)
5.3
MAX5952 toc01
5.3
5.2
DIGITAL SUPPLY CURRENT
vs. TEMPERATURE
ANALOG SUPPLY CURRENT
vs. TEMPERATURE
ANALOG SUPPLY CURRENT
vs. INPUT VOLTAGE
GATE OVERDRIVE (V)
MAX5952
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
60
85
180
-40
-15
10
35
TEMPERATURE (°C)
60
85
32
37
42
47
52
INPUT VOLTAGE (V)
_______________________________________________________________________________________
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
200
150
100
250
200
150
100
50
50
0
0
0
10
20
30
40
50
5.0
MAX5952 toc11
300
VSENSE - VEE (mV)
250
MAX5952 toc10a
350
MAX5952 toc10
300
VSENSE - VEE (mV)
DC LOAD DISCONNECT THRESHOLD
vs. TEMPERATURE
FOLDBACK CURRENT-LIMIT
THRESHOLD vs. OUTPUT VOLTAGE
DC LOAD DISCONNECT THRESHOLD (mV)
FOLDBACK CURRENT-LIMIT
THRESHOLD vs. OUTPUT VOLTAGE
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
0
VOUT - VEE (V)
10
20
30
40
50
-40
10
35
60
85
OVERCURRENT RESPONSE WAVEFORM
(MAX5952AUAX) (RLOAD = 240Ω TO 57Ω)
OVERCURRENT TIMEOUT
(RLOAD = 240Ω TO 57Ω)
MAX5952 toc12
-15
TEMPERATURE (°C)
VOUT - VEE (V)
MAX5952 toc13
(AGND - VOUT)
50V/div
0V
IOUT
200mA/div
(AGND - VOUT)
50V/div
0V
IOUT
200mA/div
0A
0V
VGATE_
10V/div
0A
VEE
VEE
INT
5V/div
0V
GATE
10V/div
INT
2V/div
400µs/div
20ms/div
SHORT-CIRCUIT RESPONSE TIME
SHORT-CIRCUIT RESPONSE TIME
MAX5952 toc14
MAX5952 toc15
(AGND - VOUT)
20V/div
(AGND - VOUT)
20V/div
0V
0V
IOUT
10A/div
IOUT
200mA/div
0A
130mA
VGATE_
10V/div
VGATE_
10V/div
VEE
20ms/div
VEE
4µs/div
_______________________________________________________________________________________
9
MAX5952
Typical Operating Characteristics (continued)
(VEE = -48V, VDD = +3.3V, VAUTO = VAGND = VDGND = 0V, RESET = SHD_ = unconnected, RSENSE = 0.5Ω, IVEE = 00, ICUT = 000,
TA = +25°C, all registers = default setting, unless otherwise noted.)
MAX5952
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
Typical Operating Characteristics (continued)
(VEE = -48V, VDD = +3.3V, VAUTO = VAGND = VDGND = 0V, RESET = SHD_ = unconnected, RSENSE = 0.5Ω, IVEE = 00, ICUT = 000,
TA = +25°C, all registers = default setting, unless otherwise noted.)
RESET TO OUT TURN-OFF DELAY
ZERO-CURRENT DETECTION WAVEFORM
MAX5952 toc16
MAX5952 toc17
RESET
2V/div
(AGND - VOUT)
20V/div
0V
0V
IOUT
200mA/div
0A
VGATE_
10V/div
VEE
IOUT
200mA/div
0A
VGATE_
5V/div
INT
2V/div
VEE
0V
100µs/div
100ms/div
OVERCURRENT RESTART DELAY
STARTUP WITH VALID PD
(25kΩ AND 0.1µF)
MAX5952 toc18
MAX5952 toc19
(AGND - VOUT)
20V/div
(AGND - VOUT)
20V/div
0V
0V
IOUT
100mA/div
IOUT
200mA/div
0A
0A
VGATE_
10V/div
VEE
VGATE_
5V/div
VEE
400ms/div
100ms/div
DETECTION WITH INVALID PD
(25kΩ AND 10µF)
DETECTION WITH INVALID PD (15kΩ)
MAX5952 toc21
MAX5952 toc20
(AGND - VOUT)
20V/div
(AGND - VOUT)
5V/div
0V
0V
IOUT
1mA/div
IOUT
1mA/div
0A
40ms/div
10
100ms/div
______________________________________________________________________________________
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
STARTUP IN MIDSPAN MODE
WITH VALID PD (25kΩ AND 0.1µF)
DETECTION WITH INVALID PD (33kΩ)
MAX5952 toc22
MAX5952 toc23
(AGND - VOUT)
5V/div
0V
(AGND - VOUT)
20V/div
0V
IOUT
100mA/div
IOUT
1mA/div
0A
0A
VGATE_
5V/div
VEE
100ms/div
100ms/div
DETECTION WITH MIDSPAN MODE
WITH INVALID PD (15kΩ)
DETECTION WITH MIDSPAN MODE
WITH INVALID PD (33kΩ)
MAX5952 toc25
MAX5952 toc24
(AGND - VOUT)
5V/div
(AGND - VOUT)
5V/div
0V
0V
0A
IOUT
1mA/div
0A
IOUT
1mA/div
VEE
VGATE_
10V/div
VEE
VGATE_
10V/div
400ms/div
400ms/div
DETECTION WITH OUTPUT SHORTED
DETECTION WITH INVALID PD (OPEN CIRCUIT,
USING TYPICAL OPERATING CIRCUIT 1)
MAX5952 toc27
MAX5952 toc26
(AGND - VOUT)
5V/div
0V
(AGND - VOUT)
5V/div
0V
IOUT
1mA/div
0A
IOUT
1mA/div
VGATE_
10V/div
VEE
VGATE_
10V/div
0A
VEE
40ms/div
40ms/div
______________________________________________________________________________________
11
MAX5952
Typical Operating Characteristics (continued)
(VEE = -48V, VDD = +3.3V, VAUTO = VAGND = VDGND = 0V, RESET = SHD_ = unconnected, RSENSE = 0.5Ω, IVEE = 00, ICUT = 000,
TA = +25°C, all registers = default setting, unless otherwise noted.)
MAX5952
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
Typical Operating Characteristics (continued)
(VEE = -48V, VDD = +3.3V, VAUTO = VAGND = VDGND = 0V, RESET = SHD_ = unconnected, RSENSE = 0.5Ω, IVEE = 00, ICUT = 000,
TA = +25°C, all registers = default setting, unless otherwise noted.)
DETECTION WITH INVALID PD (OPEN CIRCUIT,
USING TYPICAL OPERATING CIRCUIT 2)
STARTUP WITH DIFFERENT PD CLASSES
MAX5952 toc29
MAX5952 toc28
0V
(AGND - VOUT)
5V/div
0A
IOUT
1mA/div
(AGND - VOUT)
5V/div
CLASS 5
CLASS 4
CLASS 3
CLASS 2
CLASS 1
VGATE_
10V/div
VEE
IOUT
20mA/div
40ms/div
40ms/div
Pin Description
12
PIN
NAME
FUNCTION
1
RESET
2
MIDSPAN
3
INT
Open-Drain Interrupt Output. INT goes low whenever a fault condition exists. Reset the fault condition
using software or by pulling RESET low (see the Interrupt section for more information about interrupt
management).
4
SCL
Serial Interface Clock Line Input
5
SDAOUT
6
SDAIN
Hardware Reset. Pull RESET low for at least 300µs to reset the device. All internal registers reset to their
default value. The address (A0–A3), and AUTO and MIDSPAN input-logic levels latch on during low-tohigh transition of RESET. RESET is internally pulled up to VDD with a 50kΩ resistor.
Midspan Mode Input. An internal 50kΩ pulldown resistor to DGND sets the default mode to end-point PSE
operation (power-over-signal pairs). Pull MIDSPAN to VDIG to set midspan operation. The MIDSPAN value
latches after the IC is powered up or reset (see the PD Detection section).
Serial Output Data Line. Connect the data line optocoupler input to SDAOUT (see the Typical Operating
Circuits). Connect SDAOUT to SDAIN if using a 2-wire, I2C-compatible system.
Serial Interface Input Data Line. Connect the data line optocoupler output to SDAIN (see the Typical
Operating Circuits). Connect SDAIN to SDAOUT if using a 2-wire, I2C-compatible system.
______________________________________________________________________________________
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
PIN
NAME
7–10
A3–A0
11–14
DET1–DET4
15
DGND
16
VDD
17– 20
SHD1–SHD4
21
AGND
22, 25,
29, 32
SENSE4,
SENSE3,
SENSE2,
SENSE1
MOSFET Source Current-Sense Negative Inputs. Connect to the source of the power MOSFET and
connect a current-sense resistor between SENSE_ and VEE (see the Typical Operating Circuits).
23, 26,
30, 33
GATE4,
GATE3,
GATE2,
GATE1
Port_ MOSFET Gate Drivers. Connect GATE_ to the gate of the external MOSFET (see the Typical
Operating Circuits).
24, 27,
31, 34
28
35
36
FUNCTION
Address Bits. A3–A0 form the lower part of the device’s address. Address inputs default high with an
internal 50kΩ pullup resistor to VDD. The address values latch when VDD or VEE ramps up and exceeds
its UVLO threshold or after a reset. The 3 MSBs of the address are set to 010.
Detection/Classification Voltage Outputs. Use DET1 to set the detection and classification probe voltages
on port 1. Use DET1 for the AC voltage sensing of port 1 when using the AC disconnect scheme (see the
Typical Operating Circuits).
Digital Ground. Connect to digital ground.
Positive Digital Supply. Connect to a digital power supply (reference to DGND).
Port Shutdown Inputs. Pull SHD_ low to turn off the external FET on port_. Internally pulled up to VDD with
a 50kΩ resistor.
Analog Ground. Connect to the high-side analog supply.
MOSFET Drain-Output Voltage Senses. Connect OUT_ to the power MOSFET drain through a resistor
OUT4, OUT3,
(100Ω to 100kΩ). The low leakage at OUT_ limits the drop across the resistor to less than 100mV (see the
OUT2, OUT1
Typical Operating Circuits).
Low-Side Analog Supply Input. Connect the low-side analog supply to VEE (-48V). Bypass with a 1µF
capacitor between AGND and VEE.
VEE
AUTO
Auto or Shutdown Mode Input. Force AUTO high to enter auto mode after a reset or power-up. Drive low
to put the MAX5952 into shutdown mode. In shutdown mode, software controls the operational modes of
the MAX5952. A 50kΩ internal pulldown resistor defaults to AUTO low. AUTO latches when VDD or VEE
ramps up and exceeds its UVLO threshold or when the device resets. Software commands can take the
MAX5952 out of AUTO while AUTO is high.
OSC
Oscillator Input. AC-disconnect detection function uses OSC. Connect a 100Hz ±10%, 2VP-P ±5%, +1.2V
offset sine wave to OSC. If the oscillator positive peak falls below the OSC_FAIL threshold of 2V, the ports
that have the AC function enabled shut down and are not allowed to power-up. When not using the ACdisconnect detection function, leave OSC unconnected.
______________________________________________________________________________________
13
MAX5952
Pin Description (continued)
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
MAX5952
Functional Diagram
VDD
SCL
SDAIN SDAOUT
OSC_IN DGND
SHD_
CURRENT SENSING
VOLTAGE PROBING
AND
CURRENT-LIMIT
CONTROL
OSCILLATOR
MONITOR
SERIAL
PORT
INTERFACE
(SPI)
DET_
A0
DETECTION/
CLASSIFICATION
SM
A1
9-BIT ADC
CONVERTER
VOLTAGE
SENSING
OUT_
10V
ACD_ENABLE
PORT
STATE
MACHINE
(SM)
A2
REGISTER FILE
A3
50µA
A=3
GATE_
AUTO
PWR_EN
MIDSPAN
CENTRAL LOGIC UNIT
(CLU)
AC DISCONNECT
SIGNAL
(ACD)
RESET
REGISTER
FILE
INT
DGND
FAST
DISCHARGE
CONTROL
100mA 90µA
MAX
ACD
REFERENCE
CURRENT
CURRENT
MEASUREMENT
VDD
AGND
13V CLAMP
AC
DETECTION
ANALOG
BIAS/
SUPPLY
MONITOR
+10V ANALOG
SENSE_
9 BITS
ADC
CURRENT
LIMIT (ILIM)
+5V DIG
CURRENT-LIMIT
DETECTOR
VOLTAGE
REFERENCES
VEE
CURRENT
REFERENCES
OPEN CIRCUIT
(OC)
OVERCURRENT
(OVC)
FOLDBACK
CONTROL
MAX5952
14
4mV
182mV
212mV
______________________________________________________________________________________
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
The MAX5952 is a quad -48V power controller
designed for use in IEEE 802.3af-compliant/pre-IEEE
802.3at-compatible PSE. This device provides PD discovery, classification, current limit, DC and AC load
disconnect detections in compliance with the IEEE
802.3af standard. The MAX5952 is pin compatible with
the MAX5945/LTC4258/LTC4259A PSE controllers and
provides additional features.
The MAX5952 features a high-power mode which provides up to 45W per port. The device allows the user to
program the current-limit and overcurrent thresholds up
to 2.5 times the default thresholds. The MAX5952 can
also be programmed to decrease the current-limit and
overcurrent threshold by 15% for high operating voltage
conditions to keep the output power constant.
The MAX5952 provides instantaneous readout of each
port current through the I2C interface. The MAX5952 also
provides high-capacitance detection for legacy PDs.
The MAX5952 is fully software configurable and programmable through an I2C-compatible, 3-wire serial
interface with 49 registers. The class-overcurrent
detection function enables system power management
to detect if a PD draws more than the allowable current.
The MAX5952’s extensive programmability enhances
system flexibility, enables field diagnosis, and allows
for uses in other applications.
The MAX5952 provides four operating modes to suit
different system requirements. Auto mode allows the
device to operate automatically without any software
supervision. Semi-auto mode automatically detects and
classifies a device connected to a port after initial software activation but does not power up that port until
instructed to by software. Manual mode allows total
software control of the device and is useful for system
diagnostics. Shutdown mode terminates all activities
and securely turns off power to the ports.
The MAX5952 provides input undervoltage lockout, input
undervoltage detection, input overvoltage lockout,
overtemperature detection, output voltage slew-rate limit
during startup, power-good, and fault status. The
MAX5952’s programmability includes startup timeout,
overcurrent timeout, and load-disconnect detection timeout.
The MAX5952 communicates with the system microcontroller through an I 2C-compatible interface. The
MAX5952 features separate input and output data lines
(SDAIN and SDAOUT) for use with optocoupler isolation. As a slave device, the MAX5952 includes four
address inputs allowing 16 unique addresses. A separate INT output and four independent shutdown inputs
(SHD_) provide fast response from a fault to port shutdown between the MAX5952 and the microcontroller. A
RESET input allows hardware reset of the device.
Reset
Reset is a condition the MAX5952 enters after any of
the following conditions:
1) After power-up (V EE and V DD rise above their
UVLO thresholds).
2) Hardware reset. The RESET input is driven low and
back high again any time after power-up.
3) Software reset. Writing a 1 into R1Ah[4] any time
after power-up.
4) Thermal shutdown.
During a reset, the MAX5952 resets its register map to
the reset state as shown in Table 37 and latches in the
state of AUTO (pin 35) and MIDSPAN (pin 2). During
normal operation, change at the AUTO and MIDSPAN
input is ignored. While the condition that caused the
reset persists (i.e. high temperature, RESET input low,
or UVLO conditions) the MAX5952 does not acknowledge any addressing from the serial interface.
Port Reset (R1Ah[3:0])
Set high anytime during normal operation to turn off
power and clear the events and status registers of the
corresponding port. Port reset only resets the events
and status registers.
Midspan Mode
In midspan mode, the device adopts cadence timing
during the detection phase. When cadence timing is
enabled and a failed detection occurs, the port waits
between 2s and 2.4s before attempting to detect again.
Midspan mode is activated by setting R11[1] high. The
status of the MIDSPAN pin is written to R11[1] during
power-up or after a reset. MIDSPAN is internally pulled
low by a 50kΩ resistor.
______________________________________________________________________________________
15
MAX5952
Detailed Description
MAX5952
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
Operation Modes
The MAX5952 contains four independent, but identical
state machines to provide reliable and real-time control
of the four network ports. Each state machine has four
operating modes: auto mode, semi-auto mode, manual,
and shutdown. Auto mode allows the device to operate
automatically without any software supervision. Semiauto mode, upon request, continuously detects and
classifies a device connected to a port but does not
power up that port until instructed by software. Manual
mode allows total software control of the device and is
useful in system diagnostics. Shutdown mode terminates all activities and securely turns off power to the
ports.
Switching between auto, semi, or manual mode does
not interfere with the operation of the port. When the
port is set into shutdown mode, all the port operations
are immediately stopped and the port remains idle until
shutdown is exited.
Automatic (Auto) Mode
Enter automatic (auto) mode by forcing the AUTO input
high prior to a reset, or by setting R12h[P_M1,P_M0] to
[1,1] during normal operation (see Tables 16 and 16a).
In auto mode, the MAX5952 performs detection, classification, and powers up the port automatically once a
valid PD is detected at the port. If a valid PD is not connected at the port, the MAX5952 repeats the detection
routine continuously until a valid PD is connected.
Going into auto mode, the DET_EN and CLASS_EN bits
are set to high and stay high unless changed by software. Using software to set DET_EN and/or CLASS_EN
low causes the MAX5952 to skip detection and/or classification. As a protection, disabling the detection routine in auto mode does not allow the corresponding port
to power up, unless the DET_BY (R23H[4]) is set to 1.
The AUTO status is latched into the register only during a reset. Any changes to the AUTO input after reset
are ignored.
Semi-Automatic (Semi-Auto) Mode
Enter semi-auto mode by setting R12h[P_M1,P_M0] to
[1,0] during normal operation (see Tables 16 and 16a).
In semi-auto mode, the MAX5952, upon request, performs detection and/or classification repeatedly but
does not power up the port(s), regardless of the status
of the port connection.
Setting R19h[PWR_ON_] (Table 22) high immediately
terminates detection/classification routines and turns on
power to the port(s).
16
R14h[DET_EN_, CLASS_EN_] default to low in semi-auto
mode. Use software to set R14h[DET_EN_, CLASS_EN_]
to high to start the detection and/or classification routines. R14h[DET_EN_, CLASS_EN_] are reset every time
the software commands a power off of the port (either
through reset or PWR_OFF). In any other case, the status
of the bits is left unchanged (including when the state
machine turns off the power because a load disconnect
or a fault condition is encountered).
Manual Mode
Enter manual mode by setting R12h[P_M1,P_M0] to [0,1]
during normal operation (see Tables 16 and 16a).
Manual mode allows the software to dictate any
sequence of operation. Write a 1 to both R14h[DET_EN_]
and R14h[CLASS_EN_] to start detection and classification operations, respectively, and in that priority order.
After execution, the command is cleared from the register(s). PWR_ON_ has highest priority. Setting PWR_ON_
high at any time causes the device to immediately enter
the powered mode. Setting DET_EN and CLASS_EN
high at the same time causes detection to be performed
first. Once in the powered state, the device ignores
DET_EN_ or CLASS_EN_ commands.
When switching to manual mode from another mode,
DET_EN_, CLASS_EN_ default to low. These bits
become pushbutton rather than configuration bits (i.e.,
writing ones to these bits while in manual mode commands the device to execute one cycle of detection
and/or classification. The bits are reset back to zeros at
the end of the execution).
Shutdown Mode
Enter shutdown mode by forcing the AUTO input low
prior to a reset, or by setting R12h[P_M1,P_M0] to [0,0]
during normal operation (see Tables 16 and 16a). Putting
the MAX5952 into shutdown mode immediately turns off
power and halts all operations to the corresponding port.
The event and status bits of the affected port(s) are also
cleared. In shutdown mode, the DET_EN_, CLASS_EN_
and PWR_ON_ commands are ignored.
In shutdown mode, the serial interface operates normally.
PD Detection
When PD detection is activated, the MAX5952 probes
the output for a valid PD. After each detection cycle,
the device sets the DET_END_ bit R04h/05h[3:0] high
and reports the detection results in the status registers
R0Ch[2:0], R0Dh[2:0], R0Eh[2:0], and R0Fh[2:0]. The
DET_END_ bit is reset to low when read through R05h
or after a port reset.
______________________________________________________________________________________
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
An external diode, in series with the DET_ input,
restricts PD detection to the first quadrant as specified
by the IEEE 802.3af/at standard. To prevent damage to
non-PD devices, and to protect itself from an output
short circuit, the MAX5952 limits the current into DET_
to less than 2mA maximum during PD detection.
In midspan mode, the MAX5952 waits 2.2s before
attempting another detection cycle after every failed
detection. The first detection, however, happens immediately after issuing the detection command.
High-Capacitance Detection
The CLC_EN bit in register R23h[5] enables the large
capacitor detection feature for legacy PD devices.
When CLC_EN = 1, the high-capacitance detection limit
is extended up to 100µF. CLC_EN = 0 is the default
condition for the normal capacitor size detection. See
Table 1 and the Register Map and Description section.
Table 1. PSE PI Detection Modes Electrical Requirement
(Table 33-2 of the IEEE 802.3af Standard)
PARAMETER
Open-Circuit Voltage
Short-Circuit Current
SYMBOL
MIN
MAX
UNITS
VOC
—
30
V
In detection mode only
In detection mode only
ISC
—
5
mA
Valid Test Voltage
VVALID
2.8
10
V
Voltage Difference
Between Test Points
∆VTEST
1
—
V
tBP
2
—
ms
0.1
V/µs
Time Between Any Two
Test Points
Slew Rate
VSLEW
Accept Signature
Resistance
RGOOD
19
26.5
kΩ
Reject Signature
Resistance
RBAD
< 15
> 33
kΩ
Open-Circuit Resistance
ROPEN
500
—
kΩ
Accept Signature
Capacitance
CGOOD
—
150
nF
Reject Signature
Capacitance
CBAD
10
—
µF
Signature Offset Voltage
Tolerance
VOS
0
2.0
V
Signature Offset Current
Tolerance
IOS
0
12
µA
ADDITIONAL INFORMATION
This timing implies a 500Hz maximum probing
frequency
______________________________________________________________________________________
17
MAX5952
A valid PD has a 25kΩ discovery signature characteristic
as specified in the IEEE 802.3af/at standard. Table 1
shows the IEEE 802.3af/at specification for a PSE detecting a valid PD signature. See the Typical Operating
Circuits and Figure 1 (Detection, Classification, and
Power-Up Port Sequence). The MAX5952 can probe and
categorize different types of devices connected to the
port such as: a valid PD, an open circuit, a low resistive
load, a high resistive load, a high capacitive load, a positive DC supply, or a negative DC supply.
During detection, the MAX5952 keeps the external
MOSFET off and forces two probe voltages through the
DET_ input. The current through the DET_ input is measured as well as the voltage at OUT_. A two-point slope
measurement is used as specified by the IEEE 802.3af
standard to verify the device connected to the port. The
MAX5952 implements appropriate settling times and a
100ms digital integration to reject 50Hz/60Hz powerline noise coupling.
MAX5952
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
Powered Device Classification
(PD Classification)
During the PD classification mode, the MAX5952 forces
a probe voltage (-18V) at DET_ and measures the current into DET_. The measured current determines the
class of the PD.
After each classification cycle, the device sets the
CL_END_ bit (R04h/05h[7:4]) high and reports the classification results in the status registers R0Ch[6:4],
R0Dh[6:4], R0Eh[6:4], and R0Fh[6:4]. The CL_END_ bit
is reset to low when read through register R05h or after
a port reset. Both status registers, R04h, and R05h are
cleared after the port powers down. Table 2 shows the
IEEE 802.3af requirement for a PSE classifying a PD at
the power interface (PI).
The MAX5952 supports high power beyond the IEEE
802.3af standard by providing additional classifications
(Class 5 and ping-pong classification).
Powered State
When the MAX5952 enters a powered state, the tSTART
and tDISC timers are reset. Before turning on the port
power, the MAX5952 checks if any other port is not
turning on and if the t FAULT timer is zero. Another
check is performed if the ACD_EN bit is set, in this
case the OSC_FAIL bit must be low (oscillator is okay)
for the port to be powered.
Table 2. PSE Classification of a PD (Table
33-4 of the IEEE 802.3af)
MEASURED ICLASS (mA)
0 to 5
> 5 and < 8
8 to 13
> 13 and < 16
16 to 21
> 21 and < 25
25 to 31
> 31 and < 35
35 to 45
> 45 and < 51
51 to 68
If these conditions are met, the MAX5952 enters startup
where it turns on power to the port. An internal signal,
POK_, asserts high when VOUT is within 2V from VEE.
PGOOD_ status bits are set high if POK_ stays high
longer than tPGOOD. PGOOD immediately resets when
POK goes low.
The PG_CHG_ bit sets when a port powers up or down.
PWR_EN sets when a port powers up and resets when
a port shuts down. The port shutdown timer lasts 0.5ms
and prevents other ports from turning off during that
period, except in the case of emergency shutdowns
(RESET = L, RESET_IC = H, VEEUVLO, VDDUVLO, and
TSHD).
The MAX5952 always checks the status of all ports before
turning off. A priority logic system determines the order to
prevent the simultaneous turn-on or turn-off of the ports.
The port with the lesser ordinal number gets priority over
the others (i.e., port 1 turns on first, port 2 second, port 3
third and port 4 fourth). Setting PWR_OFF_ high turns off
power to the corresponding port.
80ms
0V
150ms
150ms
21.3ms
tDETI
tDETII
tCLASS
0V
-4V
CLASSIFICATION
Class 0
-9V
May be Class 0 and 1
Class 1
May be Class 1 or 2
OUT_
Class 2
May be Class 2 or 3
-18V
Class 3
May be Class 3 or 4
Class 4
May be Class 4 or 5
-48V
Class 5
Figure 1. Detection, Classification, and Power-Up Port
Sequence
18
______________________________________________________________________________________
t
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
POK
After power-off due to an overcurrent fault, and if the
RSTR_EN bit is set, the tFAULT timer is not immediately
reset but starts decrementing at the same slower pace.
The MAX5952 allows the port to be powered on only
when the tFAULT counter is at zero. This feature sets an
automatic duty-cycle protection to the external MOSFET avoiding overheating.
The MAX5952 continuously flags when the current
exceeds the maximum current allowed for the class as
indicated in the CLASS status register. When class
overcurrent occurs, the MAX5952 sets the IVC bit in
register R09h.
tPGOOD
PGOOD
ICUT Register and High-Power Mode
Figure 2. PGOOD Timing
Overcurrent Protection
A sense resistor RS connected between SENSE_ and
VEE monitors the load current. Under normal operating
conditions, the voltage across RS (VRS) never exceeds
the threshold V SU_LIM. If V RS exceeds V SU_LIM, an
internal current-limiting circuit regulates the GATE voltage, limiting the current to ILIM = VSU_LIM / RS. During
transient conditions, if VRS exceeds VSU_LIM by more
than 1V, a fast pulldown circuit activates to quickly
recover from the current overshoot. During startup, if
the current-limit condition persists, when the startup
timer, t START, times out, the port shuts off, and the
STRT_FLT_ bit is set. In the normal powered state, the
MAX5952 checks for overcurrent conditions as determined by VFLT_LIM = ~88% of VSU_LIM. The tFAULT
counter sets the maximum allowed continuous overcurrent period. The tFAULT counter increases when VRS
exceeds V FLT_LIM and decreases at a slower pace
when VRS drops below VFLT_LIM. A slower decrement
for the tFAULT counter allows for detecting repeated
short-duration overcurrents. When the counter reaches
the tFAULT limit, the MAX5952 powers off the port and
asserts the IMAX_FLT_ bit. For a continuous overstress,
a fault latches exactly after a period of tFAULT. VSU_LIM
ICUT Register
The ICUT register determines the maximum current limits allowed for each port of the MAX5952. The 3 ICUT
bits (R2Ah[6:4], R2Ah[2:0], R2Bh[6:4], and R2Bh[2:0])
allow programming of the current-limit and overcurrent
thresholds in excess of the IEEE standard limit (see
Tables 34a, 34b, and 34c). The ICUT registers can be
written to directly through the I 2 C interface when
CL_DISC (R17h[2]) is set to 0 (see Table 3). In this
case, the current limit of the port is configured regardless of the status of the classification.
By setting the CL_DISC bit to 1, the MAX5952 automatically sets the ICUT register based upon the classification result of the port. See Table 3 and the Register
Map and Description section.
Table 3. Automatic ICUT Programming
CL_DISC
PORT
CLASSIFICATION
RESULT
RESULTING ICUT
REGISTER BITS
0
Any
User programmed
1
1
ICUT = 110
1
2
ICUT = 111
1
0, 3
ICUT = 000
______________________________________________________________________________________
19
MAX5952
is programmable through the ICUT registers R2Ah[6:4],
R2Ah[2:0], R2Bh[6:4], R2Bh[2:0], and the IVEE bits in
register R29h[1:0]. See the High-Power Mode section
for more information on the ICUT register.
MAX5952
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
High-Power Mode
When CL_DISC (R17h[2]) is set to 0, high-power mode
is configured by setting the ICUT bits to any combination other than 000, 110, or 111 (note that 000 is the
default value for the IEEE standard limit). See Table 3
and the Register Map and Description section.
current source pulls down GATE_ to VEE to turn off the
MOSFET.
The pullup and pulldown current controls the maximum
slew rate at the output during turn-on or turn-off. Use
the following equation to set the maximum slew rate:
∆VOUT IGATE
=
∆t
CGD
Foldback Current
During startup and normal operation, an internal circuit
senses the voltage at OUT_ and reduces the currentlimit value when (VOUT_ - VEE) > 28V. The foldback
function helps to reduce the power dissipation on the
FET. The current limit eventually reduces to 1/3 of ILIM
when (VOUT_ - VEE ) > 48V (see Figure 3a). For highpower mode, the foldback starts when (VOUT_ - VEE ) >
10V (see Figure 3b). In high-power mode, the current
limit (ILIM) is reduced up to 1/8 of its programmed value
when (VOUT_ - VEE ) > 48V.
MOSFET Gate Driver
Connect the gate of the external n-channel MOSFET to
GATE_. An internal 50µA current source pulls GATE_ to
(VEE + 10V) to turn on the MOSFET. An internal 40µA
where CGD is the total capacitance between GATE and
DRAIN of the external MOSFET. Current limit and the
capacitive load at the drain control the slew rate during
startup. During current-limit regulation, the MAX5952
manipulates the GATE_ voltage to control the voltage at
SENSE_ (VRS). A fast pulldown activates if VRS overshoots the limit threshold (VSU_LIM). The fast pulldown
current increases with the amount of overshoot. The
maximum fast pulldown current is 100mA.
During turn-off, when the GATE voltage reaches a value
lower than 1.2V, a strong pulldown switch is activated
to keep the MOSFET securely off.
(VSENSE_ - VEE)
(VRS - VEE)
VSU_LIM
VSU_LIM
VSU_LIM / 3
VSU_LIM / 3
28V
Figure 3a. Foldback Current Characteristics
20
48V
(VOUT_ - VEE)
10V
48V
(VOUT_ - VEE)
Figure 3b. Foldback Current Characteristics for High-Power
Mode
______________________________________________________________________________________
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
Hardware Shutdown
SHD_ shuts down the respective ports without using
the serial interface. Hardware shutdown offers an emergency turn-off feature that allows a fast disconnect of
the power supply from the port. Pull SHD_ low to
remove power. SHD_ also resets the corresponding
events and status register bits.
Interrupt
The MAX5952 contains an open-drain logic output (INT)
that goes low when an interrupt condition exists. R00h
and R01h (Tables 6 and 7) contain the definitions of the
interrupt registers. The mask register R01h determines
events that trigger an interrupt. As a response to an interrupt, the controller reads the status of the event register
to determine the cause of the interrupt and takes subsequent actions. Each interrupt event register also contains
a Clear on Read (CoR) register. Reading through the
CoR register address clears the interrupt. INT remains
low when reading the interrupt through the read-only
addresses. For example, to clear a startup fault on the
port 4 read address 09h (see Table 11). Use the global
pushbutton bit in register 1Ah (bit 7, Table 23) to clear
interrupts, or use a software or hardware reset.
Undervoltage and
Overvoltage Protection
The MAX5952 contains several undervoltage and overvoltage protection features. Table 12 in the Register
Map and Description section shows a detailed list of
the undervoltage and overvoltage protection features.
An internal VEE undervoltage lockout (VEEUVLO) circuit
keeps the MOSFET off and the MAX5952 in reset until
VAGND - VEE exceeds 29V for more than 3ms. An internal VEE overvoltage (VEE_OV) circuit shuts down the
ports when (VAGND - VEE) exceeds 60V. The digital
supply also contains an undervoltage lockout
(V DDUVLO). The MAX5952 also features three other
undervoltage and overvoltage interrupts: VEE undervoltage interrupt (V EEUV ), V DD undervoltage interrupt
(VDDUV), and VDD overvoltage interrupt (VDDOV). A
fault latches into the supply events register (Table 12),
but the MAX5952 does not shut down the ports with
VEEUV, VDDUV, or VDDOV.
DC Disconnect Monitoring
Setting R13h[DCD_EN_] bits high enable DC load monitoring during a normal powered state. If VRS (the voltage
across RS) falls below the DC load disconnect threshold,
VDCTH, for more than tDISC, the device turns off power
and asserts the LD_DISC_ bit of the corresponding port.
AC Disconnect Monitoring
The MAX5952 features AC load disconnect monitoring.
Connect an external sine wave to OSC. The oscillator
requirements are:
1) VP-P x Frequency = 200VP-P x Hz ±15%
2) Positive peak voltage > +2V
3) Frequency > 60Hz
A 100Hz ±10%, 2VP-P ±5%, with +1.2V offset (VPEAK =
+2.2V typical) is recommended.
The MAX5952 buffers and amplifies 3x the external
oscillator signal and sends the signal to DET_, where
the sine wave is AC-coupled to the output. The
MAX5952 senses the presence of the load by monitoring the amplitude of the AC current returned to DET_
(see the Functional Diagram).
Setting R13h[ACD_EN_] bits high enable AC load disconnect monitoring during a normal powered state. If
the AC current peak at the DET_ input falls below IACTH
for more than tDISC, the device turns off power and
asserts the LD_DISC_ bit of the corresponding port.
IACTH is programmable using R23h[0-3].
An internal comparator checks for a proper amplitude
of the oscillator input. If the positive peak of the input
sinusoid falls below a safety value of 2V, OSC_FAIL
sets and the port shuts down. Power cannot be applied
to the ports when ACD_EN is set high and OSC_FAIL is
set high. Leave OSC unconnected or connect it to
DGND when not using AC-disconnect detection.
Thermal Shutdown
If the MAX5952 die temperature reaches +150°C, an
overtemperature fault generates and the MAX5952
shuts down. The MOSFETs turn off. The die temperature of the MAX5952 must cool down below 130°C to
remove the overtemperature fault condition. After a
thermal shutdown, the part is reset.
______________________________________________________________________________________
21
MAX5952
Digital Logic
VDD supplies power for the internal logic circuitry. VDD
ranges from +3.0V to +5.5V and determines the logic
thresholds for the CMOS connections (SDAIN,
SDAOUT, SCL, AUTO, SHD_, A_). This voltage range
enables the MAX5952 to interface with a nonisolated
low-voltage microcontroller. The MAX5952 checks the
digital supply for compatibility with the internal logic.
The MAX5952 also features a VDD undervoltage lockout
(VDDUVLO) of +2.0V. A VDDUVLO condition keeps the
MAX5952 in reset and the ports shut off. Bit 0 in the
supply event register shows the status of V DDUVLO
(Table 12) after VDD has recovered. All logic inputs and
outputs reference to DGND. DGND and AGND must be
connected together externally. Connect DGND to
AGND at a single point in the system as close as possible to the MAX5952.
MAX5952
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
Watchdog
I2C-Compatible Serial Interface
R1Dh, R1Eh, and R1Fh registers control the watchdog
operation. The watchdog function, when enabled, allows
the MAX5952 to gracefully take over control or securely
shuts down the power to the ports in case of software/
firmware crashes. Contact the factory for more details.
The MAX5952 operates as a slave that sends and
receives data through an I 2C-compatible, 2-wire or
3-wire interface. The interface uses a serial-data input
line (SDAIN), a serial-data output line (SDAOUT), and a
serial-clock line (SCL) to achieve bidirectional communication between master(s) and slave(s). A master (typically a microcontroller) initiates all data transfers to and
from the MAX5952, and generates the SCL clock that
synchronizes the data transfer. In most applications,
connect the SDAIN and the SDAOUT lines together to
form the serial-data line (SDA).
Using the separate input and output data lines allows
optocoupling with the controller bus when an isolated
supply powers the microcontroller.
Address Inputs
A3, A2, A1, and A0 represent the four LSBs of the chip
address. The complete chip address is 7 bits (see
Table 4).
Table 4. MAX5952 Address
0
1
0
A3
A2
A1
A0
R/W
The MAX5952 SDAIN line operates as an input. The
MAX5952 SDAOUT operates as an open-drain output. A
pullup resistor, typically 4.7kΩ, is required on SDAOUT.
The MAX5952 SCL line operates only as an input. A
pullup resistor, typically 4.7kΩ, is required on SCL if
there are multiple masters, or if the master in a singlemaster system has an open-drain SCL output.
The four LSBs latch on the low-to-high transition of RESET
or after a power-supply start (either on VDD or VEE).
Address inputs default high through an internal 50kΩ
pullup resistor to VDD. The MAX5952 also responds to the
call through a global address 30h (see the Global
Addressing and Alert Response Protocol section).
SDAIN
tBUF
tSU, DAT
tLOW
tSU, STA
tHD, DAT
tHD, STA
tSU, STO
SCL
tHIGH
tHD, STA
tR
tF
START CONDITION
REPEATED START CONDITION
STOP
CONDITION
START
CONDITION
Figure 4. 2-Wire Serial Interface Timing Details
SDAIN/SDA
tBUF
tSU, DAT
tLOW
tSU, STA
tHD, DAT
tHD, STA
tSU, STO
SCL
tHIGH
tHD, STA
tR
tF
START CONDITION
REPEATED START CONDITION
STOP
CONDITION
Figure 5. 3-Wire Serial Interface Timing Details
22
______________________________________________________________________________________
START
CONDITION
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
Bit Transfer
Each clock pulse transfers one data bit (Figure 7). The
data on SDA must remain stable while SCL is high.
Acknowledge
The acknowledge bit is a clocked 9th bit (Figure 8) that
the recipient uses to handshake receipt of each byte of
data. Thus each byte effectively transferred requires 9
bits. The master generates the 9th clock pulse, and the
recipient pulls down SDA (or the SDAOUT in the 3-wire
interface) during the acknowledge clock pulse, so that
the SDA line is stable low during the high period of the
clock pulse. When the master transmits to the MAX5952,
the MAX5952 generates the acknowledge bit. When the
MAX5952 transmits to the master, the master generates
the acknowledge bit.
START and STOP Conditions
Both SCL and SDA remain high when the interface is
not busy. A master signals the beginning of a transmission with a START (S) condition by transitioning SDA
from high to low while SCL is high. When the master finishes communicating with the slave, the master issues
a STOP (P) condition by transitioning SDA from low to
high while SCL is high. The STOP condition frees the
bus for another transmission.
SDA
SDA/
SDAIN
SCL
SCL
S
START
P
STOP
.
DATA LINE STABLE; CHANGE OF
DATA VALID
DATA ALLOWED
Figure 7. Bit Transfer
Figure 6. START and STOP Conditions
CLOCK PULSE FOR ACKNOWLEDGEMENT
START CONDITION
1
SCL
2
8
9
SDA
BY TRANSMITTER
S
SDA
BY RECEIVER
Figure 8. Acknowledge
______________________________________________________________________________________
23
MAX5952
Serial Addressing
Each transmission consists of a START condition (Figure
6) sent by a master, followed by the MAX5952 7-bit
slave address plus R/W bit, a register address byte, one
or more data bytes, and finally a STOP condition.
MAX5952
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
Slave Address
The MAX5952 has a 7-bit long slave address (Figure
9). The bit following the 7-bit slave address (bit eight) is
the R/W bit, which is low for a write command and high
for a read command.
010 always represents the first three bits (MSBs) of the
MAX5952 slave address. Slave address bits A3, A2,
A1, and A0 represent the states of the MAX5952’s A3,
A2, A1, and A0 inputs, allowing up to sixteen MAX5952
devices to share the bus. The states of the A3, A2, A1
and A0 latch in upon the reset of the MAX5952 into register R11h. The MAX5952 monitors the bus continuously, waiting for a START condition followed by the
MAX5952’s slave address. When a MAX5952 recognizes its slave address, the MAX5952 acknowledges
and is then ready for continued communication.
responds to the data it is delivering. If it is not, it then
backs off and frees the data line. This litigation protocol
always allows the part with the lowest address to complete the transmission. The microcontroller can then
respond to the interrupt and take proper actions. The
MAX5952 does not reset its own interrupt at the end of
the alert response protocol. The microcontroller has to
do it by clearing the event register through their CoR
adresses or activating the CLR_INT pushbutton.
Message Format for Writing to the MAX5952
A write to the MAX5952 comprises of the MAX5952’s
slave address transmission with the R/W bit set to 0, followed by at least one byte of information. The first byte
of information is the command byte (Figure 10). The
command byte determines which register of the
MAX5952 is written to by the next byte, if received. If
the MAX5952 detects a STOP condition after receiving
the command byte, the MAX5952 takes no further
action beyond storing the command byte. Any bytes
received after the command byte are data bytes. The
first data byte goes into the internal register of the
MAX5952 selected by the command byte. If the
MAX5952 transmits multiple data bytes before the
MAX5952 detects a STOP condition, these bytes store
in subsequent MAX5952 internal registers because the
control byte address auto-increments.
Global Addressing and Alert Response Protocol
The global address call is used in writing mode to write
the same register to multiple devices (address 0x60). In
read mode (address 0x61), the global address call is
used as the alert response address. When responding
to a global call, the MAX5952 puts out on the data line
its own address whenever its interrupt is active. So
does every other device connected to the SDAOUT line
that has an active interrupt. After every bit transmitted,
the MAX5952 checks that the data line effectively cor-
MSB
SDA
0
LSB
1
0
A3
A2
A1
A0
R/W
SCL
Figure 9. Slave Address
CONTROL BYTE IS STORED ON RECEIPT OF STOP CONDITION
ACKNOWLEDGE FROM MAX5952
S
SLAVE ADDRESS
0
R/W
D15
A
D14
D13
D12
D11
D10
D9
D8
CONTROL BYTE
A
P
ACKNOWLEDGE FROM MAX5952
Figure 10. Control Byte Received
24
______________________________________________________________________________________
ACK
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
Operation with Multiple Masters
When the MAX5952 operates on a 2-wire interface with
multiple masters, a master reading the MAX5952
should use repeated starts between the write which
sets the MAX5952’s address pointer, and the read(s)
that take the data from the location(s). It is possible for
master 2 to take over the bus after master 1 has set up
the MAX5952’s address pointer but before master 1
has read the data. If master 2 subsequently resets the
MAX5952’s address pointer then master 1’s read may
be from an unexpected location.
Command Address Auto-Incrementing
Address auto-incrementing allows the MAX5952 to be
configured with fewer transmissions by minimizing the
number of times the command address needs to be
sent. The command address stored in the MAX5952
generally increments after each data byte is written or
read (Table 5). The MAX5952 is designed to prevent
overwrites on unavailable register addresses and unintentional wrap-around of addresses.
Table 5. Auto-Increment Rules
COMMAND BYTE
ADDRESS RANGE
AUTO-INCREMENT BEHAVIOR
0x00 to 0x26
Command address auto-increments
after byte read or written
0x26
Command address remains at 0x26
after byte written or read
ACKNOWLEDGE FROM MAX5952
HOW CONTROL BYTE AND DATA BYTE MAP
INTO THE REGISTER
ACKNOWLEDGE FROM MAX5952
S
SLAVE ADDRESS
0
D15 D14 D13 D12 D11 D10
A
D9
ACKNOWLEDGE FROM MAX5952
D8
CONTROL BYTE
D7
D6
D5
A
D4
D3
D2
D1
D0
DATA BYTE
A
P
1 BYTE
R/W
AUTO-INCREMENT
MEMORY WORD ADDRESS
Figure 11. Control and Single Data Byte Received
ACKNOWLEDGE FROM MAX5952
HOW CONTROL BYTE AND DATA BYTE MAP
INTO THE REGISTER
ACKNOWLEDGE FROM MAX5952
S
SLAVE ADDRESS
0
R/W
D15 D14 D13 D12 D11 D10
A
CONTROL BYTE
D9
ACKNOWLEDGE FROM MAX5952
D8
D7
A
D6
D5
D4
D3
DATA BYTE
D2
D1
D0
A
P
n BYTES
AUTO-INCREMENT
MEMORY WORD ADDRESS
Figure 12. ‘n’ Data Bytes Received
______________________________________________________________________________________
25
MAX5952
Message Format for Reading
The MAX5952 reads using the MAX5952’s internally
stored command byte as an address pointer, the same
way the stored command byte is used as an address
pointer for a write. The pointer auto-increments after
reading each data byte using the same rules as for a
write. Thus, a read is initiated by first configuring the
MAX5952’s command byte by performing a write (Figure
11). The master now reads ‘n’ consecutive bytes from
the MAX5952, with the first data byte read from the register addressed by the initialized command byte (Figure
12). When performing read-after-write verification,
remember to reset the command byte’s address
because the stored control byte address auto-increments after the write.
MAX5952
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
Register Map and Description
The interrupt register (Table 6) summarizes the event
register status and is used to send an interrupt signal
(INT goes low) to the controller. Writing a 1 to R1Ah[7]
clears all interrupt and events registers. A reset sets
R00h to 00h.
INT_EN (R17h[7]) is a global interrupt mask (Table 7).
The MASK_ bits activate the corresponding interrupt
bits in register R00h. Writing a 0 to INT_EN (R17h[7])
disables the INT output.
A reset sets R01h to AAA00A00b where A is the state
of the AUTO input prior to the reset.
Table 6. Interrupt Register
ADDRESS = 00h
SYMBOL
DESCRIPTION
BIT
R/W
SUP_FLT
7
R
Interrupt signal for supply faults. SUP_FLT is the logic OR of all the bits [7:0] in register
R0Ah/R0Bh (Table 12).
TSTR_FLT
6
R
Interrupt signal for startup failures. TSTR_FLT is the logic OR of bits [7:0] in register
R08h/R09h (Table 11).
IMAX_FLT
5
R
Interrupt signal for current-limit violations. IMAX_FLT is the logic OR of bits [3:0] in register
R06h/R07h (Table 10).
CL_END
4
R
Interrupt signal for completion of classification. CL_END is the logic OR of bits [7:4] in
register R04h/R05h (Table 9).
DET_END
3
R
Interrupt signal for completion of detection. DET_END is the logic OR of bits [3:0] in
register R04h/R05h (Table 9).
LD_DISC
2
R
Interrupt signal for load disconnection. LD_DISC is the logic OR of bits [7:4] in register
R06h/R07h (Table 10).
PG_INT
1
R
Interrupt signal for PGOOD status change. PG_INT is the logic OR of bits [7:4] in register
R02h/R03h (Table 8).
PE_INT
0
R
Interrupt signal for power-enable status change. PEN_INT is the logic OR of bits [3:0] in
register R02h/R03h (Table 8).
Table 7. Interrupt Mask Register
ADDRESS = 01h
SYMBOL
DESCRIPTION
BIT
R/W
MASK7
7
R/W
Interrupt mask bit 7. A logic-high enables the SUP_FLT interrupts. A logic-low disables the
SUP_FLT interrupts.
MASK6
6
R/W
Interrupt mask bit 6. A logic-high enables the TSTR_FLT interrupts. A logic-low disables
the TSTR_FLT interrupts.
MASK5
5
R/W
Interrupt mask bit 5. A logic-high enables the IMAX_FLT interrupts. A logic-low disables
the IMAX_FLT interrupts.
MASK4
4
R/W
Interrupt mask bit 4. A logic-high enables the CL_END interrupts. A logic-low disables the
CL_END interrupts.
MASK3
3
R/W
Interrupt mask bit 3. A logic-high enables the DET_END interrupts. A logic-low disables the
DET_END interrupts.
MASK2
2
R/W
Interrupt mask bit 2. A logic-high enables the LD_DISC interrupts. A logic-low disables the
LD_DISC interrupts.
MASK1
1
R/W
Interrupt mask bit 1. A logic-high enables the PG_INT interrupts. A logic-low disables the
PG_INT interrupts.
MASK0
0
R/W
Interrupt mask bit 0. A logic-high enables the PEN_INT interrupts. A logic-low disables the
PEN_INT interrupts.
26
______________________________________________________________________________________
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
actual level of the bits. The power event register has
two addresses. When read through the R02h address,
the content of the register is left unchanged. When read
through the CoR R03h address, the register content is
cleared. A reset sets R02h/R03h = 00h.
Table 8. Power Event Register
ADDRESS =
02h
03h
BIT
R/W
R/W
PG_CHG4
7
R
CoR
PGOOD change event for port 4
PG_CHG3
6
R
CoR
PGOOD change event for port 3
PG_CHG2
5
R
CoR
PGOOD change event for port 2
PG_CHG1
4
R
CoR
PGOOD change event for port 1
PWEN_CHG4
3
R
CoR
Power enable change event for port 4
PWEN_CHG3
2
R
CoR
Power enable change event for port 3
PWEN_CHG2
1
R
CoR
Power enable change event for port 2
PWEN_CHG1
0
R
CoR
Power enable change event for port 1
SYMBOL
DESCRIPTION
DET_END_/CL_END_ is set high whenever detection/
classification is completed on the corresponding port. A
1 in any of the CL_END_ bits forces R00h[4] to 1. A 1 in
any of the DET_END_ bits forces R00h[3] to 1. As with
any of the other events register, the detect event regis-
ter has two addresses. When read through the R04h
address, the content of the register is left unchanged.
When read through the CoR R05h address, the register
content is cleared. A reset sets R04h/R05h = 00h.
Table 9. Detect Event Register
ADDRESS =
04h
05h
BIT
R/W
R/W
CL_END4
7
R
CoR
Classification completed on port 4
CL_END3
6
R
CoR
Classification completed on port 3
CL_END2
5
R
CoR
Classification completed on port 2
CL_END1
4
R
CoR
Classification completed on port 1
DET_END4
3
R
CoR
Detection completed on port 4
DET_END3
2
R
CoR
Detection completed on port 3
DET_END2
1
R
CoR
Detection completed on port 2
DET_END1
0
R
CoR
Detection completed on port 1
SYMBOL
DESCRIPTION
______________________________________________________________________________________
27
MAX5952
The power event register (Table 8) records changes in
the power status of the four ports. Any change in
PGOOD_ (R10h[7:4]) sets PG_CHG_ to 1. Any change
in the PWR_EN_ (R10h[3:0]) sets PWEN_CHG_ to 1.
PG_CHG_ and PWEN_CHG_ trigger on the edges of
PGOOD_ and PWR_EN_ and do not depend on the
MAX5952
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
LD_DISC_ is set high whenever the corresponding port
shuts down due to detection of load removal.
IMAX_FLT_ is set high when the port shuts down due to
an extended overcurrent event after a successful startup. A 1 in any of the LD_DISC_ bits forces R00h[2] to 1.
A 1 in any of the IMAX_FLT_ bits forces R00h[5] to 1.
As with any of the other events register, the fault event
register has two addresses. When read through the
R06h address, the content of the register is left
unchanged. When read through the CoR R07h
address, the register content is cleared. A reset sets
R06h/R07h = 00h.
Table 10. Fault Event Register
ADDRESS =
06h
07h
BIT
R/W
R/W
LD_DISC4
7
R
CoR
Disconnect on port 4
LD_DISC3
6
R
CoR
Disconnect on port 3
LD_DISC2
5
R
CoR
Disconnect on port 2
LD_DISC1
4
R
CoR
Disconnect on port 1
IMAX_FLT4
3
R
CoR
Overcurrent on port 4
IMAX_FLT3
2
R
CoR
Overcurrent on port 3
IMAX_FLT2
1
R
CoR
Overcurrent on port 2
IMAX_FLT1
0
R
CoR
Overcurrent on port 1
SYMBOL
DESCRIPTION
If the port remains in current limit or the PGOOD condition is not met at the end of the startup period, the port
shuts down and the corresponding STRT_FLT_ is set to
1. A 1 in any of the STRT_FLT_ bits forces R00h[6] to 1.
IVC_ is set to 1 whenever the port current exceeds the
maximum allowed limit for the class (determined during
the classification process). A 1 in any of IVC_ forces
R00h[6] to 1. When the CL_DISC (R17h[2]) is set to 1,
the port also limits the load current according to its
class as specified in the Electrical Characteristics
table. As with any of the other events register, the startup event register has two addresses. When read
through the R08h address, the content of the register is
left unchanged. When read through the CoR R09h
address, the register content is cleared. A reset sets
R08h/R09h = 00h.
Table 11. Startup Event Register
ADDRESS =
08h
09h
BIT
R/W
R/W
IVC4
7
R
CoR
Class overcurrent flag for port 4
IVC3
6
R
CoR
Class overcurrent flag for port 3
IVC2
5
R
CoR
Class overcurrent flag for port 2
IVC1
4
R
CoR
Class overcurrent flag for port 1
STRT_FLT4
3
R
CoR
Startup failed on port 4
STRT_FLT3
2
R
CoR
Startup failed on port 3
STRT_FLT2
1
R
CoR
Startup failed on port 2
STRT_FLT1
0
R
CoR
Startup failed on port 1
SYMBOL
28
DESCRIPTION
______________________________________________________________________________________
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
OSC_FAIL is set to 1 whenever the amplitude of the
oscillator signal at the OSC_ input falls below a level
that might compromise the AC disconnect detection
function. OSC_FAIL generates an interrupt only if at
least one of the ACD_EN (R13h[7:4]) bits is set high.
A thermal shutdown circuit monitors the temperature of
the die and resets the MAX5952 if the temperature
exceeds +150°C. TSD is set to 1 after the MAX5952
returns to normal operation. TSD is also set to 1 after
every UVLO reset.
When VDD and/or |VEE| is below its UVLO threshold, the
MAX5952 is in reset mode and securely holds all ports
off. When VDD and |VEE| rise to above their respective
UVLO thresholds, the device comes out of reset as
soon as the last supply crosses the UVLO threshold.
The last supply corresponding UV and UVLO bits in the
supply event register is set to 1.
A 1 in any supply event register’s bits forces R00h[7] to
1. As with any of the other events register, the supply
event register has two addresses. When read through
the R0Ah address, the content of the register is left
unchanged. When read through the CoR R0Bh
address, the register content is cleared. A reset sets
R0Ah/R0Bh to 10100001b if VDD comes up after VEE or
to 10010100b if VEE comes up after VDD.
Table 12. Supply Event Register
ADDRESS =
SYMBOL
BIT
0Ah
0Bh
R/W
R/W
DESCRIPTION
TSD
7
R
CoR
Overtemperature shutdown
VDD_OV
6
R
CoR
VDD overvoltage condition
VDD_UV
5
R
CoR
VDD undervoltage condition
VEE_UVLO
4
R
CoR
VEE undervoltage lockout condition
VEE_OV
3
R
CoR
VEE overvoltage condition
VEE_UV
2
R
CoR
VEE undervoltage condition
OSC_FAIL
1
R
CoR
Oscillator amplitude is below limit
VDD_UVLO
0
R
CoR
VDD undervoltage lockout condition
______________________________________________________________________________________
29
MAX5952
The MAX5952 continuously monitors the power supplies and sets the appropriate bits in the supply event
register (Table 12). VDD_OV/VEE_OV is set to 1 whenever V DD /V EE exceeds its overvoltage threshold.
V DD_UV /V EE_UV is set to 1 whenever V DD /V EE falls
below its undervoltage threshold.
MAX5952
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
The port status register (Table 13a) records the results of
the detection and classification at the end of each phase
in three encoding bits each. R0Ch contains the detection
and classification status of port 1. R0Dh corresponds to
port 2, R0Eh corresponds to port 3, and R0Fh corresponds to port 4. Tables 13b and 13c show the detection/classification result decoding charts, respectively.
For CLC_EN = 0, the detection result is shown in Table
13b. When CLC_EN is set high, the MAX5952 allows valid
detection of high capacitive load of up to 100µF.
When ping-pong classification is not enabled (ENx_CL6
= 0), the classification status is reported in Table 13c.
When ping-pong classification is enabled (ENx_CL6 =
1), the CLASS_[2:0] bits are set to 000 and the classification result is reported in locations R2Ch–R2Fh.
As a protection, when POFF_CL (R17h[3], Table 21) is
set to 1, the MAX5952 prohibits turning on power to the
port that returns a status 111 after classification. A reset
sets 0Ch, 0Dh, 0Eh, and 0Fh = 00h.
Table 13a. Port Status Registers
ADDRESS = 0Ch, 0Dh, 0Eh, 0Fh
SYMBOL
Reserved
CLASS_
Reserved
DET_ST_
DESCRIPTION
BIT
R/W
7
R
Reserved
6
R
CLASS_[2]
5
R
CLASS_[1]
4
R
CLASS_[0]
3
R
Reserved
2
R
DET_[2]
1
R
DET_[1]
0
R
DET_[0]
Table 13b. Detection Result Decoding Chart
DET_ST_[2:0]
(ADDRESS = 0Ch, 0Dh, 0Eh, 0Fh)
DETECTED
DESCRIPTION
000
None
Detection status unknown
001
DCP
Positive DC supply connected at the port (AGND - VOUT_ < 1V)
010
HIGH CAP
High capacitance at the port (> 8.5µF)
011
RLOW
Low resistance at the port, RPD < 15kΩ
100
DET_OK
Detection pass, 15kΩ > RPD > 33kΩ
101
RHIGH
High resistance at the port, RPD > 33kΩ
110
OPEN0
Open port (I < 10µA)
111
DCN
Negative DC supply connected to the port (VOUT - VEE < 2V)
Table 13c. Classification Result Decoding
Chart
CLASS_[2:0]
(ADDRESS = 0Ch, 0Dh, 0Eh, 0Fh)
CLASS RESULT
000
Unknown
001
1
010
2
011
3
100
4
101
5
30
110
0
111
Current limit (> ICILIM)
______________________________________________________________________________________
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
PWR_EN_ is set to 1 when the port power is turned on.
PWR_EN resets to 0 as soon as the port turns off. Any
transition of PGOOD_ and PWR_EN_ bits set the corresponding bit in the power event registers R02h/R03h
(Table 8). A reset sets R10h = 00h.
Table 14. Power Status Register
ADDRESS = 10h
SYMBOL
DESCRIPTION
BIT
R/W
PGOOD4
7
R
Power-good condition on port 4
PGOOD3
6
R
Power-good condition on port 3
PGOOD2
5
R
Power-good condition on port 2
PGOOD1
4
R
Power-good condition on port 1
PWR_EN4
3
R
Power is enabled on port 4
PWR_EN3
2
R
Power is enabled on port 3
PWR_EN2
1
R
Power is enabled on port 2
PWR_EN1
0
R
Power is enabled on port 1
A3, A2, A1, A0 (Table 15) represent the four LSBs of
the MAX5952 address (Table 4). During a reset, the
device latches into R11h. These four bits address from
the corresponding inputs as well as the state of the
MIDSPAN and AUTO inputs. Changes to those inputs
during normal operation are ignored.
Table 15. Address Input Status Register
ADDRESS = 11h
SYMBOL
Reserved
BIT
R/W
7
R
DESCRIPTION
Reserved
Reserved
6
R
Reserved
A3
5
R
Device address, A3 pin latched-in status
A2
4
R
Device address, A2 pin latched-in status
A1
3
R
Device address, A1 pin latched-in status
A0
2
R
Device address, A0 pin latched-in status
MIDSPAN
1
R
MIDSPAN input’s latched-in status
AUTO
0
R
AUTO input’s latched-in status
______________________________________________________________________________________
31
MAX5952
PGOOD_ is set to 1 (Table 14) at the end of the powerup startup period if the power-good condition is met (0
< (VOUT - VEE) < PGTH). The power-good condition
must remain valid for more than t PGOOD to assert
PGOOD_. PGOOD_ is reset to 0 whenever the output
falls out of the power-good condition. A fault condition
immediately forces PGOOD_ low.
MAX5952
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
The MAX5952 uses two bits for each port to set the mode
of operation. Set the modes according to Table 16a.
A reset sets R12h = AAAAAAAA where A represents
the latched-in state of the AUTO input prior to the reset.
Use software to change the mode of operation.
Software resets of ports (RESET_P_ bit, Table 23) do
not affect the mode register.
Table 16. Mode Register
ADDRESS = 12h
SYMBOL
DESCRIPTION
BIT
R/W
P4_M1
7
R/W
MODE[1] for port 4
P4_M0
6
R/W
MODE[0] for port 4
P3_M1
5
R/W
MODE[1] for port 3
P3_M0
4
R/W
MODE[0] for port 3
P2_M1
3
R/W
MODE[1] for port 2
P2_M0
2
R/W
MODE[0] for port 2
P1_M1
1
R/W
MODE[1] for port 1
P1_M0
0
R/W
MODE[0] for port 1
Table 16a. Mode Status
MODE
DESCRIPTION
00
Shutdown
01
Manual
10
Semi-auto
11
Auto
Setting DCD_EN_ to 1 enables the DC load disconnect
detection feature (Table 17). Setting ACD_EN_ to 1
enables the AC load disconnect feature. If enabled, the
load disconnect detection starts during power mode
and after startup when the corresponding PGOOD_ bit
in register R10h (Table 14) goes high. A reset sets
R13h = 0000AAAA where A represents the latched-in
state of the AUTO input prior to the reset.
Table 17. Load Disconnect Detection Enable Register
ADDRESS = 13h
SYMBOL
DESCRIPTION
BIT
R/W
ACD_EN4
7
R/W
Enable AC disconnect detection on port 4
ACD_EN3
6
R/W
Enable AC disconnect detection on port 3
ACD_EN2
5
R/W
Enable AC disconnect detection on port 2
ACD_EN1
4
R/W
Enable AC disconnect detection on port 1
DCD_EN4
3
R/W
Enable DC disconnect detection on port 4
DCD_EN3
2
R/W
Enable DC disconnect detection on port 3
DCD_EN2
1
R/W
Enable DC disconnect detection on port 2
DCD_EN1
0
R/W
Enable DC disconnect detection on port 1
32
______________________________________________________________________________________
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
When entering auto mode, R14h defaults to FFh. When
entering semi or manual modes, R14h defaults to 00h.
A reset or power-up sets R14h = AAAAAAAAb where A
represents the latched-in state of the AUTO input prior
to the reset.
Table 18. Detection and Classification Enable Register
ADDRESS = 14h
SYMBOL
DESCRIPTION
BIT
R/W
CLASS_EN4
7
R/W
Enable classification on port 4
CLASS_EN3
6
R/W
Enable classification on port 3
CLASS_EN4
5
R/W
Enable classification on port 2
CLASS_EN3
4
R/W
Enable classification on port 1
DET_EN4
3
R/W
Enable detection on port 4
DET_EN3
2
R/W
Enable detection on port 3
DET_EN2
1
R/W
Enable detection on port 2
DET_EN1
0
R/W
Enable detection on port 1
CL_DISC (R17h[2]) and ENx_CL6 (R1Ch[7:4]) are used
to program the high-power mode. See Table 3 for details.
Setting BCKOFF_ to 1 (Table 19) enables cadence timing on each port where the port backs off and waits
2.2s after each failed load discovery detection. The
IEEE 802.3af standard requires a PSE that delivers
power through the spare pairs (midspan PSE) to have
cadence timing.
A reset or power-up sets R15h = 0000XXXXb where ‘X’
is the logic AND of the MIDSPAN and AUTO inputs.
Table 19. Backoff and High-Power Enable Register
ADDRESS = 15h
SYMBOL
DESCRIPTION
BIT
R/W
BCKOFF4
3
R/W
Enable cadence timing on port 4
BCKOFF3
2
R/W
Enable cadence timing on port 3
BCKOFF2
1
R/W
Enable cadence timing on port 2
BCKOFF1
0
R/W
Enable cadence timing on port 1
______________________________________________________________________________________
33
MAX5952
Setting DET_EN_/CLASS_EN_ to 1 (Table 18) enables
load detection/classification, respectively. Detection
always has priority over classification. To perform classification without detection, set the DET_EN_ bit low
and CLASS_EN_ bit high.
In manual mode, R14h works like a pushbutton. Set the
bits high to begin the corresponding routine. The bit
clears after the routine finishes.
MAX5952
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
TSTART[1,0] (Table 20a) programs the startup timers.
Startup time is the time the port is allowed to be in current limit during startup. TFAULT[1,0] programs the
fault time. Fault time is the time allowed for the port to
be in current limit during normal operation. RSTR[1,0]
programs the discharge rate of the TFAULT_ counter
and effectively sets the time the port remains off after
an overcurrent fault. TDISC[1,0] programs the load disconnect detection time. The device turns off power to
the port if it fails to provide a minimum power maintenance signal for longer than the load disconnect detection time (TDISC).
Set the bits in R16h to scale the tSTART, tFAULT, and
tDISC to a multiple of their nominal value specified in the
Electrical Characteristics table.
When the MAX5952 shuts down a port due to an
extended overcurrent condition (either during startup or
normal operation), if RSTR_EN is set high, the part does
not allow the port to power back on before the restart
timer (Table 20b) returns to zero. This effectively sets a
minimum duty cycle that protects the external MOSFET
from overheating during a prolonged output overcurrent conditions. A reset sets R16h = 00h.
Table 20a. Timing Register
ADDRESS = 16h
SYMBOL
DESCRIPTION
BIT
R/W
RSTR[1]
7
R/W
Restart timer programming bit 1
RSTR[0]
6
R/W
Restart timer programming bit 0
TSTART[1]
5
R/W
Startup timer programming bit 1
TSTART[0]
4
R/W
Startup timer programming bit 0
TFAULT[1]
3
R/W
Overcurrent timer programming bit 1
TFAULT[0]
2
R/W
Overcurrent timer programming bit 0
TDISC[1]
1
R/W
Load disconnect timer programming bit 1
TDISC[0]
0
R/W
Load disconnect timer programming bit 0
Table 20b. Startup, Fault, and Load Disconnect Timer Values for Timing Register
34
BIT [1:0]
(ADDRESS = 16h)
RSTR
tDISC
tSTART
tFAULT
00
16 x tFAULT
tSTART nominal (60ms, typ)
1/2 x tSTART nominal
tFAULT nominal (60ms, typ)
1/2 x tFAULT nominal
01
32 x tFAULT
tDISC nominal (350ms, typ)
1/4 x tDISC nominal
10
64 x tFAULT
1/2 x tDISC nominal
2 x tSTART nominal
2 x tFAULT nominal
11
0 x tFAULT
2 x tDISC nominal
4 x tSTART nominal
4 x tFAULT nominal
______________________________________________________________________________________
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
CL_DISC, together with EN_HP_CL_ (R15h[6:4]),
EN_HP_ALL (R15h[7]), and ENx_CL6 (R1Ch[7:4]) are
used to program the high-power mode. See Table 3 for
details.
Setting OUT_ISO high (Table 21), forces DET_ to a
high-impedance state.
A reset sets R17h = 0xC0.
Table 21. Miscellaneous Configurations 1
ADDRESS = 17h
SYMBOL
INT_EN
BIT
R/W
7
R/W
DESCRIPTION
A logic-high enables INT functionality
RSTR_EN
6
R
A logic-high enables the autorestart protection time off (as set by the RSTR[1:0] bits)
Reserved
5
R
Reserved
Reserved
4
R
Reserved
POFF_CL
3
R
A logic-high prevents power-up after a classification failure (I > 50mA, valid only in AUTO
mode)
CL_DISC
2
R/W
A logic-high enables reduced current-limit voltage threshold (VFLT_LIM) according to port
OUT_ISO
1
R/W
Forces DET_ to high impedance. Does not interfere with other circuit operation.
Power-enable pushbutton for semi and manual modes
is found in Table 22. Setting PWR_ON_ to 1 turns on
power to the corresponding port. Setting PWR_OFF_ to
1 turns off power to the port. PWR_ON_ is ignored
when the port is already powered and during shutdown. PWR_OFF_ is ignored when the port is already
off and during shutdown. After execution, the bits reset
to 0. During detection or classification, if PWR_ON_
goes high, the MAX5952 gracefully terminates the current operation and turns on power to the port. The
MAX5952 ignores the PWR_ON_ in auto mode. A reset
sets R19h = 00h.
Table 22. Power-Enable Pushbuttons
ADDRESS = 19h
SYMBOL
DESCRIPTION
BIT
R/W
PWR_OFF4
7
W
A logic-high powers off port 4
PWR_OFF3
6
W
A logic-high powers off port 3
PWR_OFF2
5
W
A logic-high powers off port 2
PWR_OFF1
4
W
A logic-high powers off port 1
PWR_ON4
3
W
A logic-high powers on port 4
PWR_ON3
2
W
A logic-high powers on port 3
PWR_ON2
1
W
A logic-high powers on port 2
PWR_ON1
0
W
A logic-high powers on port 1
______________________________________________________________________________________
35
MAX5952
Setting CL_DISC to 1 (Table 21) enables port over
class current protection, where MAX5952 scales down
the overcurrent limit (VFLT_LIM) according to the port
classification status. This feature provides protection to
the system against PDs that violate their maximum
class current allowance.
The higher current setting is enabled only after a successful startup so that the PD powers up as a normal
15W device.
MAX5952
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
Writing a 1 to CLR_INT (Table 23) clears all the event
registers and the corresponding interrupt bits in register R00h. Writing a 1 to RESET_P_ turns off power to the
corresponding port and resets only the status and
event registers of that port. After execution, the bits
reset to 0. Writing a 1 to RESET_IC causes a global
software reset, after which the register map is set back
to its reset state. A reset sets R1Ah = 00h.
Table 23. Global Pushbuttons
ADDRESS = 1Ah
SYMBOL
DESCRIPTION
BIT
R/W
CLR_INT
7
W
Reserved
6
Reserved
5
RESET_IC
4
W
A logic-high resets the MAX5952
RESET_P4
3
W
A logic-high softly resets port 4
RESET_P3
2
W
A logic-high softly resets port 3
RESET_P2
1
W
A logic-high softly resets port 2
RESET_P1
0
W
A logic-high softly resets port 1
A logic-high clears all interrupts
Reserved
Reserved
The ID register (Table 24) keeps track of the device ID
number and revision. The MAX5952’s ID_CODE[4:0] =
11000b. Contact the factory for REV[2:0] value.
Table 24. ID Register
ADDRESS = 1Bh
SYMBOL
ID_CODE
REV
36
DESCRIPTION
BIT
R/W
7
R
ID_CODE[4]
6
R
ID_CODE[3]
5
R
ID_CODE[2]
4
R
ID_CODE[1]
3
R
ID_CODE[0]
2
R
REV [2]
1
R
REV [1]
0
R
REV [0]
______________________________________________________________________________________
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
SMODE_ also goes high each and every time the software tries to power on a port, but is denied since the
port is in hardware mode. A reset sets R1Ch = 00h.
Table 25. SMODE Enable Register
ADDRESS = 1Ch
SYMBOL
DESCRIPTION
BIT
CoR
SMODE4
3
CoR
Port 4 hardware control flag
SMODE3
2
CoR
Port 3 hardware control flag
SMODE2
1
CoR
Port 2 hardware control flag
SMODE1
0
CoR
Port 1 hardware control flag
Set EN_WHDOG (R1Fh[7]) to 1 to enable the watchdog
function. When activated, the watchdog timer counter,
WDTIME[7:0], continuously decrements toward zero
once every 164ms. Once the counter reaches zero
(also called watchdog expiry), the MAX5952 enters
hardware-controlled mode and each port shifts to a
mode set by the HWMODE_ bit in register R1Fh (Table
27). Use software to set WDTIME (Table 26) and continuously set this register to some nonzero value before
the register reaches zero to prevent a watchdog expiry.
In this way, the software gracefully manages the power
to ports upon a system crash or switchover.
While in hardware-controlled mode, the MAX5952
ignores all requests to turn the power on and the flag
SMODE_ indicates that the hardware has taken control
of the MAX5952 operation. In addition, the software is
not allowed to change the mode of operation in hardware-controlled mode. A reset sets R1Eh = 00h.
Table 26. Watchdog Register
ADDRESS = 1Eh
SYMBOL
WDTIME
DESCRIPTION
BIT
R/W
7
R/W
WDTIME[7]
6
R/W
WDTIME[6]
5
R/W
WDTIME[5]
4
R/W
WDTIME[4]
3
R/W
WDTIME[3]
2
R/W
WDTIME[2]
1
R/W
WDTIME[1]
0
R/W
WDTIME[0]
______________________________________________________________________________________
37
MAX5952
Enable the SMODE function (Table 25) by setting
EN_WHDOG (R1Fh[7]) to 1. SMODE_ bit goes high
when the watchdog counter reaches zero and the
port(s) switch over to hardware-controlled mode.
MAX5952
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
Setting EN_WHDOG (Table 27) high activates the
watchdog counter. When the counter reaches zero, the
port switches to the hardware-controlled mode determined by the corresponding HWMODE_ bit. A low in
HWMODE_ switches the port into shutdown by setting
the bits in register R12h to 00. A high in HWMODE_
switches the port into auto mode by setting the bits in
register R12h to 11. If WD_INT_EN is set, an interrupt is
sent if any of the SMODE bits are set. A reset sets R1Fh
= 00h.
Table 27. Switch Mode Register
ADDRESS = 1Fh
SYMBOL
BIT
DESCRIPTION
R/W
EN_WHDOG
7
R/W
A logic-high enables the watchdog function
WD_INT_EN
6
R/W
Enables interrupt on SMODE_ bits
Reserved
5
—
Reserved
Reserved
4
R/W
Reserved
HWMODE4
3
R/W
Port 4 switches to AUTO if logic-high and to SHUTDOWN if logic-low when watchdog timer
expires
HWMODE3
2
R/W
Port 3 switches to AUTO if logic-high and to SHUTDOWN if logic-low when watchdog timer
expires
HWMODE2
1
R/W
Port 2 switches to AUTO if logic-high and to SHUTDOWN if logic-low when watchdog timer
expires
HWMODE1
0
R/W
Port 1 switches to AUTO if logic-high and to SHUTDOWN if logic-low when watchdog timer
expires
The CLC_EN enables the large capacitor detection feature. When CLC_EN is set the device can recognize a
capacitor load up to 100µF. If the CLC_EN is reset, the
MAX5952 performs normal detection.
AC_TH allows programming of the threshold of the AC
disconnect comparator. The threshold is defined as a
current since the comparators verify that the peak of
the current pulses sensed at the DET_ input exceed a
preset threshold. The current threshold is defined as
follows:
IAC_TH = 226.68µA + 28.33 x NAC_TH
where NAC_TH is the decimal value of AC_TH.
When set low, DET_BY inhibits port power-on if the discovery detection was bypassed in auto mode. When
set high, DET_BY allows the device to turn on power to
a non-IEEE 802.3af load without doing detection. If
OSCF_RS is set high, the OSC_FAIL bit is ignored. A
reset or power-up sets R23h = 04h. Default IAC_TH is
340µA.
Table 28. Program Register
ADDRESS = 23h
SYMBOL
DESCRIPTION
BIT
R/W
Reserved
7
—
Reserved
Reserved
6
—
Reserved
CLC_EN
5
R/W
Large capacitor detection enable
DET_BY
4
R/W
Enables skipping detection in AUTO mode
OSCF_RS
3
R/W
OSC_FAIL reset bit
2
R/W
AC_TH[2]
1
R/W
AC_TH[1]
0
R/W
AC_TH[0]
AC_TH
38
______________________________________________________________________________________
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
MAX5952
Table 29. High-Power Mode Register
ADDRESS = 24h
SYMBOL
Reserved
DESCRIPTION
BIT
R/W
7
—
Reserved
3
—
Reserved
2
—
Reserved
1
—
Reserved
0
—
Reserved
Table 30. Reserved
ADDRESS = 25h
SYMBOL
Reserved
DESCRIPTION
BIT
R/W
7
—
Reserved
6
—
Reserved
5
—
Reserved
4
—
Reserved
3
—
Reserved
2
—
Reserved
1
—
Reserved
0
—
Reserved
Table 31. Reserved
ADDRESS = 26h
SYMBOL
Reserved
DESCRIPTION
BIT
R/W
7
—
Reserved
6
—
Reserved
5
—
Reserved
4
—
Reserved
3
—
Reserved
2
—
Reserved
1
—
Reserved
0
—
Reserved
______________________________________________________________________________________
39
MAX5952
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
The IVEE bits enable the current-limit scaling (Table
32). This feature is used to reduce the current limit for
systems running at higher voltage to maintain the
desired output power. Table 33 sets the current-limit
scaling register. A reset or power-up sets R29h = 00h.
Table 32. Miscellaneous Configurations 2
Table 33. Current-Limit Scaling Register
ADDRESS = 29h
SYMBOL
Reserved
IVEE
IVEE[1:0]
(ADDRESS = 29h)
CURRENT LIMIT
(%)
Reserved
00
Default
—
Reserved
01
-5
—
Reserved
10
-10
4
—
Reserved
11
-15
3
—
Reserved
2
—
Reserved
1
R/W
IVEE[1]
0
R/W
IVEE[0]
BIT
R/W
7
—
6
5
DESCRIPTION
The three ICUT_ bits (Tables 34a and 34b) allow programming of the current-limit and overcurrent thresholds
in excess of the IEEE 802.3af standard limit. The
MAX5952 can automatically set the ICUT register or can
be manually written to by the software (see Table 3).
Class 1 and 2 limits can also be programmed by software independently from the classification status. See
Table 3. A reset or power-up sets R2Ah = R2Bh = 00h.
Table 34a. ICUT Registers 1 and 2
ADDRESS = 2Ah
SYMBOL
Reserved
ICUT2
Reserved
ICUT1
DESCRIPTION
BIT
R/W
7
—
Reserved
6
R/W
ICUT2[2]
5
R/W
ICUT2[1]
4
R/W
ICUT2[0]
3
—
Reserved
2
R/W
ICUT1[2]
1
R/W
ICUT1[1]
0
R/W
ICUT1[0]
Table 34b. ICUT Registers 3 and 4
ADDRESS = 2Bh
SYMBOL
Reserved
BIT
DESCRIPTION
R/W
7
—
Reserved
6
R/W
ICUT4[2]
ICUT4
5
R/W
ICUT4[1]
4
R/W
ICUT4[0]
Reserved
3
—
Reserved
2
R/W
ICUT3[2]
1
R/W
ICUT3[1]
0
R/W
ICUT3[0]
ICUT3
40
______________________________________________________________________________________
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
MAX5952
Table 34c. ICUT Register Bit Values for Current-Limit Threshold
ICUT_[2:0] (ADDRESS = 2Ah, 2Bh)
SCALE FACTOR
TYPICAL CURRENT-LIMIT THRESHOLD (mA)
000
1x
375
001
1.5x
563
010
1.75x
656
011
2x
750
100
2.25x
844
101
2.5x
938
110
0.3x
Class 1
111
0.53x
Class 2
Table 35. Classification Status Registers
ADDRESS = 2Ch, 2Dh, 2Eh, 2Fh
SYMBOL
Reserved
DESCRIPTION
BIT
R/W
7
—
Reserved
6
—
Reserved
The MAX5952 provides current readout for each port
during classification and normal power mode. The current per port information is separated into 9 bits. They
are organized into 2 consecutive registers for each one
of the ports. The information can be quickly retrieved
using the auto-increment option of the address pointer.
To avoid the LSB register changing while reading the
MSB, the information is frozen once the addressing
byte points to any of the current readout registers.
During power mode, the current value can be calculated as
IPORT = NIPD_ x 1.953125mA
During classification, the current is
ICLASS = NIPD_ x 0.0975mA
where NIPD_ is the decimal value of the 9-bit word. The
ADC saturates both at full scale and at zero. A reset
sets R30h–R37h = 00h.
Table 36. Current Registers
ADDRESS = 30h, 31h, 32h, 33h, 34h,
35h, 36h, 37h
SYMBOL
IPD_
DESCRIPTION
BIT
R/W
7
W
IPD_[8]
6
W
IPD_[7]
5
W
IPD_[6]
4
W
IPD_[5]
3
W
IPD_[4]
2
W
IPD_[3]
1
W
IPD_[2]
0
W
IPD_[1]/IPD_[0]
______________________________________________________________________________________
41
MAX5952
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
Table 37. Register Summary
ADDR
REGISTER NAME
R/W
PORT
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
RESET
STATE
INTERRUPTS
00h
Interrupt
RO
G
SUP_FLT
TSTR_FLT
IMAX_FLT
CL_END
DET_END
LD_DISC
PG_INT
PE_INT
0000,0000
01h
Int Mask
R/W
G
MASK7
MASK6
MASK5
MASK4
MASK3
MASK2
MASK1
MASK0
AAA0,0A00
4321
PG_CHG4
PG_CHG3
PG_CHG2
PG_CHG1
PWEN_
CHG4
PWEN_
CHG3
PWEN_
CHG2
PWEN_
CHG1
0000,0000
CL_END4
CL_END3
CL_END2
CL_END1
DET_END4
DET_END3
DET_END2
DET_END1
LD_DISC4
LD_DISC3
LD_DISC2
LD_DISC1
IMAX_FLT4
IMAX_FLT3
IMAX_FLT2
IMAX_FLT1
IVC4
IVC3
IVC2
IVC1
STRT_FLT4
STRT_FLT3
STRT_FLT2
STRT_FLT1
TSD
VDD_OV
VDD_UV
VEE_UVLO
VEE_OV
VEE_UV
OSC_FAIL
VDD_UVLO
EVENTS
02h
Power Event
RO
03h
Power Event CoR
CoR
04h
Detect Event
RO
05h
Detect Event CoR
CoR
06h
Fault Event
RO
07h
Fault Event CoR
CoR
08h
Tstart Event
RO
09h
Tstart Event CoR
CoR
0Ah
Supply Event
RO
0Bh
Supply Event CoR
CoR
0Ch
Port 1 Status
RO
1
Reserved
CLASS1[2]
CLASS1[1]
CLASS1[0]
Reserved
DET_ST1[2]
DET_ST1[1]
DET_ST1[0]
0000,0000
0Dh
Port 2 Status
RO
2
Reserved
CLASS2[2]
CLASS2[1]
CLASS2[0]
Reserved
DET_ST2[2]
DET_ST2[1]
DET_ST2[0]
0000,0000
0Eh
Port 3 Status
RO
3
Reserved
CLASS3[2]
CLASS3[1]
CLASS3[0]
Reserved
DET_ST3[2]
DET_ST3[1]
DET_ST3[0]
0000,0000
0Fh
Port 4 Status
RO
4
Reserved
CLASS4[2]
CLASS4[1]
CLASS4[0]
Reserved
DET_ST4[2]
DET_ST4[1]
DET_ST4[0]
0000,0000
10h
Power Status
RO
4321
PGOOD4
PGOOD3
PGOOD2
PGOOD1
PWR_EN4
PWR_EN3
PWR_EN2
PWR_EN1
0000,0000
11h
Pin Status
RO
G
Reserved
Reserved
A3
A2
A1
A0
MIDSPAN
AUTO
00A3A2,
A1A0MA
AAAA,AAAA
4321
4321
4321
4321
0000,0000
0000,0000
0000,0000
0001,0000*
STATUS
CONFIGURATION
12h
Operating Mode
R/W
4321
P4_M1
P4_M0
P3_M1
P3_M0
P2_M1
P2_M0
P1_M1
P1_M0
13h
Disconnect Enable
R/W
4321
ACD_EN4
ACD_EN3
ACD_EN2
ACD_EN1
DCD_EN4
DCD_EN3
DCD_EN2
DCD_EN1
0000,AAAA
14h
Det/Class Enable
R/W
4321
CLASS_EN4
CLASS_EN3
CLASS_EN2
CLASS_EN1
DET_EN4
DET_EN3
DET_EN2
DET_EN1
AAAA,AAAA
15h
Backoff Enable
R/W
4321
—
—
—
—
BCKOFF4
BCKOFF3
BCKOFF2
BCKOFF1
0000,XXXX
16h
Timing Config
R/W
G
RSTR[1]
RSTR[0]
TSTART[1]
TSTART[0]
TFAULT[1]
TFAULT[0]
TDISC[1]
TDISC[0]
0000,0000
17h
Misc Config 1
R/W
G
INT_EN
RSTR_EN
Reserved
Reserved
POFF_CL
CL_DISC
OUT_ISO
HP_TIME
1100,0000
Reserved
Reserved
PUSHBUTTONS
18h
Reserved
R/W
G
Reserved
Reserved
19h
Power Enable
WO
4321
PWR_OFF4
PWR_OFF3
1Ah
Global
WO
G
CLR_INT
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
PWR_ON4
PWR_ON3
PWR_ON2
PWR_ON1
0000,0000
RESET_IC
RESET_P4
RESET_P3
RESET_P2
RESET_P1
0000,0000
PWR_OFF2 PWR_OFF1
GENERAL
1Bh
ID
RO
G
ID_CODE[4]
ID_CODE[3]
ID_CODE[2]
ID_CODE[1]
ID_CODE[0]
REV [2]
REV [1]
REV [0]
1100,0000
1Ch
SMODE Register
CoR
4321
—
—
—
—
SMODE4
SMODE3
SMODE2
SMODE1
0000,0000
1Dh
Reserved
G
Reserved
Reserved
Reserved
Reserved
1EH
Watchdog Register
R/W
G
WDTIME[7]
WDTIME[6]
1FH
Switch Mode
Register
R/W
4321
EN_WHDOG
WD_INT_EN
42
WDTIME[5] WDTIME[4]
reserved
CSCM
Reserved
Reserved
Reserved
Reserved
WDTIME[3]
WDTIME[2]
WDTIME[1]
WDTIME[0]
0000,0000
HWMODE4
HWMODE3
HWMODE2
HWMODE1
0000,0000
______________________________________________________________________________________
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
ADDR
REGISTER NAME
R/W
PORT
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
RESET
STATE
MAXIM RESERVED
20H
Reserved
G
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
21H
Reserved
G
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
22H
Reserved
G
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
23H
Program 1
R/W
4321
Reserved
Reserved
CLC_EN
DET_BY
OSCF_RS
AC_TH[2]
AC_TH[1]
AC_TH[0]
24h
High Power Mode
R/W
G
Reserved
—
—
—
Reserved
Reserved
Reserved
Reserved
0000,0000
25h
Reserved
—
G
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
0000,0000
26h
Reserved
—
G
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
0000,0000
27H
Reserved
G
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
28H
Reserved
G
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
29H
Misc Config 2
R/W
1234
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
IVEE[1]
IVEE[0]
0000,0000
2AH
ICUT Register 1
R/W
21
Reserved
ICUT2[2]
ICUT2[1]
ICUT2[0]
Reserved
ICUT1[2]
ICUT1[1]
ICUT1[0]
0000,0000
2BH
ICUT Register 2
R/W
43
Reserved
ICUT4[2]
ICUT4[1]
ICUT4[0]
Reserved
ICUT3[2]
ICUT3[1]
ICUT[30]
0000,0000
0000,0000
CLASSIFICATION REGISTERS
2CH
Port 1 Class
RO
1
Reserved
Reserved
—
—
—
—
—
—
0000,0000
2DH
Port 2 Class
RO
2
Reserved
Reserved
—
—
—
—
—
—
0000,0000
2EH
Port 3 Class
RO
3
Reserved
Reserved
—
—
—
—
—
—
0000,0000
2FH
Port 4 Class
RO
4
Reserved
Reserved
—
—
—
—
—
—
0000,0000
CURRENT REGISTER
30H
Current Port 1 (MSB)
RO
1
IPD1[8]
IPD1[7]
IPD1[6]
IPD1[5]
IPD1[4]
IPD1[3]
IPD1[2]
IPD1[1]
0000,0000
31H
Current Port 1 (LSB)
RO
1
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
IPD1[0]
0000,0000
32H
Current Port 2 (MSB)
RO
2
IPD2[8]
IPD2[7]
IPD2[6]
IPD2[5]
IPD2[4]
IPD2[3]
IPD2[2]
IPD2[1]
0000,0000
33H
Current Port 2 (LSB)
RO
2
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
IPD2[0]
0000,0000
34H
Current Port 3 (MSB)
RO
3
IPD3[8]
IPD3[7]
IPD3[6]
IPD3[5]
IPD3[4]
IPD3[3]
IPD3[2]
IPD3[1]
0000,0000
35H
Current Port 3 (LSB)
RO
3
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
IPD3[0]
0000,0000
36H
Current Port 4 (MSB)
RO
4
IPD4[8]
IPD4[7]
IPD4[6]
IPD4[5]
IPD4[4]
IPD4[3]
IPD4[2]
IPD4[1]
0000,0000
37H
Current Port 4 (LSB)
RO
4
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
IPD4[0]
0000,0000
*UV and UVLO bits of VEE and VDD asserted depends on the order VEE and VDD supplies are brought up.
A = AUTO pin state before reset.
M = MIDSPAN state before reset.
A3...0 = ADDRESS input states before reset.
______________________________________________________________________________________
43
MAX5952
Table 37. Register Summary (continued)
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
MAX5952
Applications Information
RJ–45
CONNECTOR
1
3
RX1+
RD1+
RX1-
RD1-
24
1
22
2
1/2 OF
21
H2005A TX1+
4
TD1+*
19
TX1-
PHY
5
3
6
TD1-
-48VOUT
0.1µF
RXT1
23
75Ω
4
0.1µF
5
0.1µF
TXCT1
75Ω
20
1000pF
250VAC
75Ω
75Ω
7
0.1µF
8
-48VRTN
VCC (3.3V)
VDD
ISOLATION
1.8V TO 5V,
(REF TO DGND)
3kΩ
AGND
VDD
180Ω
A0
A1
A2
A3
1kΩ
RESET
INTERNAL
50kΩ PULLUP
3kΩ
HPCL063L
SERIAL INTERFACE
VCCRTN
4.7kΩ
INT
SDAOUT
OPTIONAL BUFFER
180Ω
MIDSPAN
INTERNAL PULLDOWN
(SIGNAL MODE)
MAX5952
HPCL063L
OPTIONAL BUFFER
180Ω
INTERNAL PULLDOWN
(MANUAL MODE)
3kΩ
SDAIN
SDA
AUTO
OSC_IN
SINE WAVE
100Hz ±10%
PEAK AMPLITUDE 2.2V ±0.1V
VALLEY AMPLITUDE 0.2V ±0.1V
3kΩ
SCL
HPCL063L
ON
SHD_
SCL
OFF
OPTIONAL BUFFER
DGND
VEE
SENSE_ GATE_
OUT_
0.5Ω
1%
100Ω
DET_
1N4448
1kΩ
0.47µF
100V
SMBJ
58CA
-48V
1N4002
FDT3612
100V, 120mΩ
SOT-223
*USE HALO TG111-HRPE40NY OR
PULSE HX6015NL FOR HIGH POWER
1 OF 4 CHANNELS
Figure 13. PoE System Block Diagram
44
______________________________________________________________________________________
0.1µF
2.2MΩ
-48VOUT
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
MAX5952
RJ–45
CONNECTOR
1
2
DATA
3
6
4
5
7
8
-48VOUT
-48VRTN
VCC (3.3V)
VDD
ISOLATION
1.8V TO 5V
(REF TO DGND)
3kΩ
AGND
VDD
180Ω
A0
A1
A2
A3
1kΩ
RESET
INTERNAL
50kΩ PULLUP
3kΩ
HPCL063L
SERIAL INTERFACE
VCCRTN
4.7kΩ
INT
SDAOUT
OPTIONAL BUFFER
180Ω
SDAIN
MAX5952
HPCL063L
SDA
OPTIONAL BUFFER
180Ω
AUTO
INTERNAL PULLDOWN
(MANUAL MODE)
MIDSPAN
INTERNAL PULLDOWN
(SIGNAL MODE)
3kΩ
OSC_IN
SINE WAVE
100Hz ±10%
PEAK AMPLITUDE 2.2V ±0.1V
VALLEY AMPLITUDE 0.2V ±0.1V
3kΩ
SCL
HPCL063L
ON
SHD_
SCL
OFF
OPTIONAL BUFFER
DGND
VEE
SENSE_ GATE_
OUT_
0.5Ω
1%
100Ω
DET_
1kΩ
1N4448
0.47µF
100V
SMBJ
58CA
0.1µF
2.2MΩ
-48VOUT
-48V
1N4002
FDT3612
100V, 120mΩ
SOT-223
1 OF 4 CHANNELS
Figure 14. PoE System Block Diagram
______________________________________________________________________________________
45
MAX5952
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
R10
2Ω
L1
68µH, DO3308P-683
R6
1Ω
D1
DIODES INC.: B1100
C3
15nF
C4
220µF
Sanyo 6SVPA220MAA
R5
1kΩ
R1
2.61kΩ
+3.3V
300mA
C5
4.7µF
Q2
MMBTA56
Q4
MMBTA56
GND
+3.3V
GND
GND
DRAIN
1
2
3
C6
0.47µF
100V
4
V+
MAX5020
VCC
VDD
NDRV
FB
GND
CS
SS_SHDN
8
R8
30Ω
7
6
Q3
MMBTA56
Q1
Si2328 DS
C9
4.7nF
SOURCE
5
C7
0.22µF
C1
0.1µF
C2
0.022µF
GATE
C8
2.2µF
R4
1Ω
R9
1Ω
-48V
R2
6.81kΩ
R7
1.02kΩ
R3
2.61kΩ
-48V
Figure 15. -48V to +3.3V (300mA) Boost Converter Solution for VDIG
Figure 16. Layout Example for Boost Converter Solution for VDIG
46
______________________________________________________________________________________
965 (mils)
1700 (mils)
965 (mils)
1700 (mils)
965 (mils)
1700 (mils)
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
DESIGNATION
DESCRIPTION
C1
0.1µF, 25V ceramic capacitor
C2
0.022µF, 25V ceramic capacitor
C3
15nF, 25V ceramic capacitor
DESIGNATION
Q1
Q2, Q3, Q4
DESCRIPTION
Si2328DS
Vishay n-channel MOSFET, SOT23
MMBTA56 small-signal PNP
R1, R3
2.61kΩ ±1% resistors
R2
6.81kΩ ±1% resistor
C4
220µF capacitor Sanyo 6SVPA220MAA
C5
4.7µF, 16V ceramic capacitor
C6
0.47µF, 100V ceramic capacitor
R4, R6, R9
C7
0.22µF, 16V ceramic capacitor
R5
1kΩ ±1% resistor
C8
2.2µF, 16V ceramic capacitor
R7
1.02kΩ ±1% resistor
C9
4.7nF, 16V ceramic capacitor
R8
30Ω ±1% resistor
D1
B1100 100V Schottky diode
R10
2Ω ±1% resistor
U1
High-voltage PWM IC
MAX5020ESA (8-pin SO)
68µH inductor
Coilcraft DO3308P-683 or equivalent
L1
1Ω ±1% resistors
Pin Configuration
Selector Guide
PART
TOP VIEW
RESET 1
+
36 OSC
2
35 AUTO
INT 3
34 OUT1
MIDSPAN
SCL
4
33 GATE1
SDAOUT
5
32 SENSE1
SDAIN
6
A3
7
30 GATE2
A2
8
29 SENSE2
A1
9
28 VEE
MAX5952
A0 10
SENSE RESISTOR (Ω)
VDD (V)
MAX5952A_
0.5
3.3
MAX5952C_
0.5
5
31 OUT2
27 OUT3
DET1 11
26 GATE3
DET2 12
25 SENSE3
DET3 13
24 OUT4
DET4 14
23 GATE4
DGND 15
22 SENSE4
VDD 16
21 AGND
SHD1 17
20 SHD4
SHD2 18
19 SHD3
SSOP
______________________________________________________________________________________
47
MAX5952
Component List for VDIG Supply
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
MAX5952
Typical Operating Circuits
-48V RTN
OUTPUT TO PORT
-48VRTN
VCC (3.3V)
ISOLATION
VDD
1.8V TO 3.7V,
(REF TO DGND)
3kΩ
AGND
VDD
180Ω
A0
A1
A2
A3
1kΩ
RESET
3kΩ
INTERNAL
50kΩ PULLUP
SERIAL INTERFACE
VCCRTN
HPCL063L
180Ω
SDAOUT
OPTIONAL BUFFER
INT
3kΩ
AUTO
INTERNAL PULLDOWN
(MANUAL MODE)
MIDSPAN
INTERNAL PULLDOWN
(SIGNAL MODE)
SDAIN
MAX5952
HPCL063L
SDA
OPTIONAL BUFFER
180Ω
4.7kΩ
OSC_IN
3kΩ
N.C.
SCL
HPCL063L
ON
SHD_
SCL
OFF
OPTIONAL BUFFER
DGND
VEE
SENSE_ GATE_
OUT_
0.5Ω
1%
100Ω
DET_
1N4448
-48V
OUTPUT TO
PORT
-48V
FDT3612
100V, 120mΩ
SOT-223
NOTE: ALL SIGNAL PINS ARE REFERENCED TO DGND.
DGND RANGE IS BETWEEN VEE AND (AGND + 4V).
CAN BE UP TO 100kΩ
1 OF 4 CHANNELS
Typical Operating Circuit 1 (without AC Load Removal Detection)
48
______________________________________________________________________________________
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
-48V RTN
OUTPUT TO PORT
-48VRTN
VDD
ISOLATION
VCC (3.3V)
1.8V TO 3.7V,
(REF TO DGND)
3kΩ
AGND
VDD
180Ω
A0
A1
A3
A2
1kΩ
RESET
INTERNAL
50kΩ PULLUP
3kΩ
HPCL063L
SERIAL INTERFACE
VCCRTN
4.7kΩ
INT
SDAOUT
OPTIONAL BUFFER
180Ω
SDAIN
MAX5952
HPCL063L
SDA
OPTIONAL BUFFER
180Ω
AUTO
INTERNAL PULLDOWN
(MANUAL MODE)
MIDSPAN
INTERNAL PULLDOWN
(SIGNAL MODE)
3kΩ
OSC_IN
SINE WAVE
100Hz ±10%
PEAK AMPLITUDE 2.2V ±0.1V
VALLEY AMPLITUDE 0.2V ±0.1V
3kΩ
SCL
HPCL063L
ON
SHD_
SCL
OFF
OPTIONAL BUFFER
DGND
VEE
SENSE_ GATE_
OUT_
0.5Ω
1%
DET_
100Ω
1kΩ
1N4448
0.47μF
100V
-48V
OUTPUT TO
PORT
-48V
NOTE: ALL SIGNAL PINS ARE REFERENCED TO DGND.
DGND MUST BE CONNECTED DIRECTLY TO AGND
FOR AC DISCONNECT DETECTION CIRCUIT TO OPERATE.
1N4002
FDT3612
100V, 120mΩ
SOT-223
CAN BE UP TO 100kΩ
1 OF 4 CHANNELS
Typical Operating Circuit 2 (with AC Load Removal Detection)
Chip Information
PROCESS: BiCMOS
Package Information
For the latest package outline information and land patterns, go
to www.maxim-ic.com/packages. Note that a “+”, “#”, or “-” in
the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status.
PACKAGE TYPE
PACKAGE CODE
DOCUMENT NO.
36 SSOP
A36-4
21-0040
______________________________________________________________________________________
49
MAX5952
Typical Operating Circuits (continued)
MAX5952
High-Power, Quad, PSE Controller
for Power-Over-Ethernet
Revision History
REVISION
NUMBER
REVISION
DATE
0
7/07
Initial release
1
1/10
Revised the General Description, Features, Electrical Characteristics
table, and Detailed Description.
DESCRIPTION
PAGES
CHANGED
—
1, 7, 15
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
50 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2010 Maxim Integrated Products
Maxim is a registered trademark of Maxim Integrated Products, Inc.