Title 21 W Standby Power Supply using TNY280P Specification Input: 85 – 295 VAC (110 – 420 VDC) Outputs: 5 V / 4 A; 15 V / 67 mA Application General PC-Standby Supply Author Power Integrations Applications Department Document Number DER-114 Date June 28, 2006 Revision 1.0 Summary and Features • • • • • High standby efficiency: PIN < 0.70 W @ POUT = 0.5 W, at 230 VAC input Under-voltage lockout (UVLO) function: glitch-free startup and shutdown Two means of implementing output overvoltage protection (OVP) EEL22 transformer core meets clearance and creepage requirements Output overload, short circuit and open feedback loop protection The products and applications illustrated herein (including circuits external to the products and transformer construction) may be covered by one or more U.S. and foreign patents or potentially by pending U.S. and foreign patent applications assigned to Power Integrations. A complete list of Power Integrations’ patents may be found at www.powerint.com. Power Integrations 5245 Hellyer Avenue, San Jose, CA 95138 USA. Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com DER-114 PC Standby Power Supply – TNY280P June 28, 2006 Table Of Contents 1 2 3 4 Introduction .................................................................................................................3 Power Supply Specification ........................................................................................4 Schematic ...................................................................................................................5 Circuit Description.......................................................................................................6 4.1 Input Rectifier & filter ...........................................................................................6 4.2 TNY280 Primary ..................................................................................................6 4.3 Output Rectification .............................................................................................7 4.4 Output Feedback .................................................................................................7 4.5 UV Lockout ..........................................................................................................7 4.6 OV Protection ......................................................................................................7 5 PCB Layout.................................................................................................................9 6 Bill Of Materials.........................................................................................................10 7 Transformer Specification .........................................................................................11 7.1 Electrical Diagram..............................................................................................11 7.2 Electrical Specifications .....................................................................................11 7.3 Materials ............................................................................................................11 7.4 Transformer Build Diagram................................................................................12 7.5 Transformer Construction ..................................................................................12 8 Transformer Spreadsheets .......................................................................................13 9 Performance Data.....................................................................................................16 9.1 Efficiency ...........................................................................................................16 9.2 No-load Input Power ..........................................................................................16 9.3 0.5 W (5 V, 0.1 A) Load Input Power .................................................................17 9.4 Available Standby Output Power .......................................................................17 9.5 Regulation .........................................................................................................18 9.5.1 Load ...........................................................................................................18 9.5.2 Line.............................................................................................................18 10 Thermal Performance............................................................................................19 11 Waveforms ............................................................................................................20 11.1 Drain Voltage and Current, Normal Operation...................................................20 11.2 Drain Voltage & Current Startup Profile .............................................................21 11.3 Output Voltage Startup Profile ...........................................................................21 11.4 OV Shutdown ....................................................................................................22 11.5 Load Transient Response (3 A to 4 A Load Step) .............................................23 11.6 Output Ripple Measurements ............................................................................24 11.6.1 Ripple Measurement Technique.................................................................24 11.6.2 Measurement Results.................................................................................25 12 Design Notes:........................................................................................................26 13 Revision History ....................................................................................................27 Important Note: Although this board is designed to satisfy safety isolation requirements, the engineering prototype has not been agency approved. Therefore, all testing should be performed using an isolation transformer to provide the AC input to the prototype board. Page 2 of 28 Power Integrations Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com DER-114 PC Standby Power Supply – TNY280P June 28, 2006 1 Introduction This engineering report describes a universal input 5 V, 4 A power supply designed around a TNY280P device from the TinySwitch-III family of ICs. Although designed as an auxiliary or bias supply for a personal computer (PC) power supply, this design can also be used as a general-purpose evaluation platform for TinySwitch-III devices. Typically, PC power supplies have a power factor corrected (PFC) input stage. However, since the bias supply must operate before the PFC stage is active, this supply has been designed for universal input operation. Input rectification and input storage capacitance have been included, for evaluation purposes. This stage and the EMI filter components would normally be part of the main PC supply, in an actual application. This report contains the power supply specification, the circuit diagram, a complete bill of materials (BOM), the PI Xls transformer spreadsheet design results, complete transformer documentation, the printed circuit board (PCB) layout and relevant performance data. Figure 1– Populated Circuit Board Photograph. Page 3 of 28 Power Integrations Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com DER-114 PC Standby Power Supply – TNY280P June 28, 2006 2 Power Supply Specification Description Input Voltage Frequency No-load Input Power (230 VAC) Output Output Voltage 1 Output Ripple Voltage 1 Output Current 1 Output Voltage 2 Output Current 2 Total Output Power Continuous Output Power Efficiency Full Load Ambient Temperature Page 4 of 28 Symbol Min Typ Max Units Comment VIN fLINE 85 47 VAC Hz W Equivalent to 100 – 420 VDC 50/60 295 64 0.3 VOUT1 VRIPPLE1 IOUT1 VOUT2 4.75 5 5.25 50 4 18 67 V mV A V mA 21 W 50 o 12 15 POUT η TAMB 76 0 % C ± 5% 20 MHz bandwidth 100 mA minimum load on VOUT1 & 40 mA load on auxiliary output o Measured at POUT 25 C Free convection, sea level Power Integrations Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com DER-114 PC Standby Power Supply – TNY280P June 28, 2006 3 Schematic Figure 2 – Circuit Diagram. Page 5 of 28 Power Integrations Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com DER-114 PC Standby Power Supply – TNY280P June 28, 2006 4 Circuit Description This dual output converter is configured as a Flyback. The main output provides 4 A at 5 V, while the bias winding on transformer T1 is used to generate a 15 V output that can supply up to 67 mA. The converter will operate over an input voltage range of 85 – 295 VAC or 100 – 420 VDC. The 5 V output is referenced to a TL431 located on the secondary side, and feedback is passed back to the primary through optocoupler (U2). 4.1 Input Rectifier & filter This circuit is designed for standby applications and components F1, RT1, D1-D4 & C1 are only provided for standalone testing. Fuse F1 will effectively isolate the converter from the supply source in the event of short circuit failure. Thermistor RT1 limits the inrush current at startup. Diodes D1, D2, D3 & D4 form a bridge rectifier, which charges the bulk storage capacitor C1. 4.2 TNY280 Primary The TNY280P device (U1) is an integrated circuit, which includes a power MOSFET, an oscillator, control, start-up and protection functions. A clamp circuit (D5, VR1, C3, R1 & R3) limits the voltage that appears on the drain of U1 each time its MOSFET turns off. During normal operation VR1 does not conduct and clamping is performed by D5, C3, R1 & R3. Typically, VR1 will only conduct during fault conditions such as overload. This approach allows the RCD clamp (R1, R3, C3 & D5) to be sized for normal operation, which maximizes efficiency at light load. The output of the bias/auxiliary supply winding is rectified by diode D6 and filtered by capacitor C4. The rectified and filtered output of the bias winding (terminals J5 & J6) can be used to power external circuitry on the primary side, such as the PFC and main converter control circuits. The bias winding is also used to supply current to the TNY280 BYPASS/MULTIFUNCTION (BP/M) pin during steady state operation. The value of R4 is selected to deliver the IC supply current to the BP/M pin, thereby inhibiting the internal high-voltage current source that normally charges the BP/M pin capacitor (C2). This results in reduced input power consumption under light load and no load conditions. Capacitor C2 provides high frequency decoupling of the internally generated 5.85 V IC supply voltage. Three different capacitor values could be used for C2, which would select one of three internal current limit sets. A 0.1 uF capacitor was used in this design, which selects the standard current limit set for a TNY280P. The transistor of optocoupler U2 pulls current out of the ENABLE/UNDER-VOLTAGE (EN/UV) pin of U1. The IC keeps switching as long as the current drawn from its EN/UV pin is less than 90 µA. It stops switching whenever the current drawn from the EN/UV pin exceeds that threshold, which ranges from 90 µA to 150 µA (with the typical value being 115 µA). By enabling and disabling switching pulses, the feedback loop regulates the output voltage of the power supply. Page 6 of 28 Power Integrations Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com DER-114 PC Standby Power Supply – TNY280P June 28, 2006 An internal state machine sets the MOSFET current limit to one of four levels, depending on the main output load current. This ensures that the effective switching frequency remains above the audible frequency range. The lowest current limit (used at no-load) makes the transformer flux density so low that dip-varnished transformers produce no perceptible audible noise. 4.3 Output Rectification Diode D7 rectifies the main output. Low ESR capacitors C7, C8 & C9 attenuate the switching ripple. A post filter (L1 & C10) further reduces switching ripple and noise on the main output. 4.4 Output Feedback Resistors R6 and R7 form a voltage divider network. A portion of the output voltage is fed into the input terminal of the TL431 (U3). The TL431 varies its cathode voltage in an attempt to keep its input voltage constant (equal to 2.5 V, ±2%). As the cathode voltage changes, the current through the LED and transistor within U2 change. Whenever the EN/UV pin current exceeds its threshold, the next switching cycle is disabled. Whenever the EN/UV pin current falls below the threshold, the next switching cycle is enabled. As the load is reduced, the number of enabled switching cycles decreases, which lowers the effective switching frequency and the switching losses. This results in almost constant efficiency down to very light loads, which is ideal for meeting energy efficiency requirements. Capacitor C12 rolls off the gain of U3 with frequency, to ensure stable operation. Capacitor C11 prevents the output voltage from overshooting at startup. 4.5 UV Lockout Optional resistors R11 and R12–connected between the DC bus and the EN/UV pin of U1–enable the under-voltage lockout function. When these resistors are used, start-up is inhibited until the current into the EN/UV pin exceeds 25 µA. The values of R11 and R12 sets a startup voltage threshold that prevents output voltage glitches when the input voltage is abnormally low, such as when the AC input capacitor is discharging during shutdown. Additionally, the UVLO status is checked whenever a loss of regulation occurs–such as during an output overload or short-circuit. This effectively latches U1 off until the input voltage is removed and reapplied. With the values of R11 and R12 shown in figure 2, the UVLO threshold is approximately 100 VDC (71 VAC). 4.6 OVP This supply has two different overvoltage protection circuits. The first OVP function is provided by VR2 and the latching shutdown function built into U1. If the feedback loop became an open circuit–due to the failure of U2, for example–the main output voltage and the bias winding voltage would both rise. Once the bias voltage exceeded the sum of the voltage across VR2 and the BP/M pin voltage, current would flow into the BP/M pin. When that current exceeds the OV shutdown threshold (≈5.5 mA), the latching shutdown function is triggered and MOSFET switching is disabled. MOSFET switching remains disabled until the BP/M pin capacitor (C2) is discharged below 4.8 V. Page 7 of 28 Power Integrations Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com DER-114 PC Standby Power Supply – TNY280P June 28, 2006 The second OVP function is provided by VR3, U4 and R10, and is enabled when jumpers JP1 and JP2 are installed (forms a second feedback loop). If the primary feedback loop became an open circuit, the output voltage would rise. The EN/UV pin would be pulled low once the output voltage exceeded the voltage across VR3 and the LED within U4. The output voltage would then be regulated at a slightly higher voltage than that of the primary feedback loop. Page 8 of 28 Power Integrations Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com DER-114 PC Standby Power Supply – TNY280P June 28, 2006 5 PCB Layout Figure 3 – Printed Circuit Layout. Page 9 of 28 Power Integrations Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com DER-114 PC Standby Power Supply – TNY280P June 28, 2006 6 Bill Of Materials Item Qty Part Ref Value 1 1 C1 100 µF 2 3 2 1 C2 C12 C3 100 nF 1 nF 4 5 6 1 1 1 C4 C5 C6 100 µF 1 nF 470 pF 7 3 C7 C8 C9 1500 µF 8 1 C10 470 µF 9 10 11 1 1 4 C11 C13 D1 D2 D3 D4 2.2 µF 22 nF 1N4007 12 2 D5 D6 1N4937 13 14 1 1 D7 F1 15TQ060 3.15 A 15 16 1 2 HS1 J1 J4 6032B-TT CON1 17 18 3 1 J2 J5 J6 J3 CON1 CON1 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 2 1 1 1 1 1 1 2 1 1 1 2 1 1 1 JP1 JP2 L1 R1 R2 R3 R4 R5 R6 R7 R8 R9 R10 R11 R12 R13 RT1 T1 J 3.3 µH 200 kΩ 3 kΩ 30 Ω 16 kΩ 33 Ω 10 kΩ 47 Ω 1 kΩ 100 Ω 2.0 MΩ 4.7 Ω 16 Ω EEL22 34 1 U1 TNY280P 35 2 U2 U4 PC817A 36 1 U3 37 38 39 1 1 1 VR1 VR2 VR3 TL431 P6KE150 A 1N5247B 1N5231C Page 10 of 28 Description 100 µF, 450 V, Electrolytic, Low ESR, (18 x 30) 100 nF, 50 V, Ceramic, X7R 1 nF, 1 kV, Disc Ceramic 100 µF, 35 V, Electrolytic, Gen. Purpose, (8 x 11.5) 1 nF, Ceramic, Y1 470 pF, 100 V, Ceramic, X7R 1500 µF, 10 V, Electrolytic, Very Low ESR, 22 mΩ, (10 x 25) 470 µF, 10 V, Electrolytic, Low ESR, 120 mΩ, (8 x 12) 2.2 µF, 50 V, Electrolytic, Gen. Purpose, (5 x 11) 22 nF, 630 V, Film 1000 V, 1 A, Rectifier, DO-41 600 V, 1 A, Fast Recovery Diode, 200 ns, DO-41 60 V, 15 A, Schottky, TO-220AC 3.15 A, 250 V, Fast, TR5 HEATSINK, Straight Fin, 8.3 °C/W, TO-220 Test Point, BLK,THRU-HOLE MOUNT Test Point, WHT,THRU-HOLE MOUNT Test Point, RED,THRU-HOLE MOUNT Wire Jumper, Non insulated, 22 AWG, 0.2 in 3.3 µH, 5.5 A, 8.5 x 11 mm 200 kΩ, 5%, 1/2 W, Carbon Film 3 kΩ, 5%, 1/2 W, Carbon Film 30 Ω, 5%, 1/2 W, Carbon Film 16 kΩ, 5%, 1/4 W, Carbon Film 33 Ω, 5%, 1/4 W, Carbon Film 10 kΩ, 1%, 1/4 W, Metal Film 47 Ω, 5%, 1/4 W, Carbon Film 1 kΩ, 5%, 1/4 W, Carbon Film 100 Ω, 5%, 1/4 W, Carbon Film 2.0 MΩ, 5%, 1/4 W, Carbon Film 4.7 Ω, 5%, 1/4 W, Carbon Film NTC Thermistor, 16 Ω, 2.7 A Bobbin, EEL22, Vertical, 10 pins TinySwitch-III, TNY280P, DIP-8C Opto coupler, 35 V, CTR 80-160%, 4DIP 2.495 V Shunt Regulator IC, 2%, 0 to 70C, TO-92 150 V, 5 W, 5%, TVS, DO204AC (DO15) 17 V, 5%, 500 mW, DO-35 5.1 V, 2%, 500 mW, DO-35 Mfg Part Number EPAG451ELL101M M35S B37987F5104K000 / ECU-S1H104KBB ECK-D3A102KBP KME35VB101M6X1 1LL 440LD10 ECU-S2A471KBA EKZE100ELL152MJ 25S ELXZ100ELL471MH 12D EKME500ELL2R2M E11D ECQ-E6223KF 1N4007 1N4937 Mfg Nippon ChemiCon Epcos/Panasonic Panasonic Nippon ChemiCon Vishay Panasonic Nippon ChemiCon Nippon ChemiCon Nippon ChemiCon Panasonic Vishay 15TQ060 370 1315 041 Vishay International Rectifier Wickmann 6032B-TT 5011 AAVID/Thermalloy Keystone 5012 5010 Keystone Keystone 298 R622LY-3R3M CFR-50JB-200K CFR-50JB-3K0 CFR-50JB-30R CFR-25JB-16K CFR-25JB-33R MFR-25FBF-10K0 CFR-25JB-47R CFR-25JB-1K0 CFR-25JB-100R CFR-25JB-2M0 CFR-25JB-4R7 CL170 YC-2207 TNY280P Alpha Toko Yageo Yageo Yageo Yageo Yageo Yageo Yageo Yageo Yageo Yageo Yageo Thermometrics Ying Chin Power Integrations PC817X1 Sharp TL431CLP Texas Instruments P6KE150A 1N5247B 1N5231C Vishay Microsemi Microsemi Power Integrations Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com DER-114 PC Standby Power Supply – TNY280P June 28, 2006 7 Transformer Specification 7.1 Electrical Diagram Figure 4 – Transformer Electrical Diagram. 7.2 Electrical Specifications Electrical Strength Primary Inductance Resonant Frequency Primary Leakage Inductance 7.3 1 second, 60 Hz, from Pins 1-5 to Pins 7-10 Pins 1-3, all other windings open, measured at 100 kHz, 0.4 VRMS Pins 1-3, all other windings open Pins 1-3, with Pins 7-10 shorted, measured at 100 kHz, 0.4 VRMS 3000 VAC 1084 µH, -/+10% 1200 kHz (Min.) 28 µH (Max.) Materials Item [1] [2] [3] [4] [5] [6] [7] [8] [9] Description Core: PC40 - EEL22 with air gap GAPPED ALG VALUE- 131nH/T2 Bobbin: EEL-22, 10 Pin Bobbin (Ying Chin YC-2207/ Pin Shine P-2204 or equivalent) Magnet Wire: #28 AWG Heavy Nyleze Copper Foil 12 mm X 0.1 mm Tape: 3M #44 Polyester Web Margin Tape 3 mm wide Tape, 3M 1298 Polyester Film 18.5 mm, 0.002” Thick Tape, 3M 1298 Polyester Film 12.5 mm, 0.002” Thick Tape, 3M 1298 Polyester Film 4 mm, 0.002” Thick Varnish Page 11 of 28 Power Integrations Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com DER-114 7.4 PC Standby Power Supply – TNY280P June 28, 2006 Transformer Build Diagram Figure 5a – Transformer Build Diagram. Figure 5b – Secondary Tape Preparation. 7.5 Figure 5c – Secondary Tape Cross-Section Transformer Construction Bobbin Preparation Primary Margin Primary WD#1 Basic Insulation Secondary Margin Secondary WD # 2 Basic Insulation Bias Margin Bias Winding WD # 3 Basic Insulation Primary Margin Primary WD#4 Outer Wrap Core Assembly Varnish Page 12 of 28 Set up Bobbin with pins oriented to the left hand side Apply 3.0 mm wide margin to both sides of bobbin using item [5]. Match height of primary windings. Start at Pin 3. Wind 30 turns of item [3] in approximately 1 layer. Add 1 Layer of Tape [7] for insulation. Wind remaining 30 primary turns, finish on Pin 2. Use two layers of item [6] for basic insulation. Apply 3.0 mm wide margin to both sides of bobbin using item [5]. Match height of secondary winding. Prepare Copper Foil as shown in figure 5b & 5c above. Starting at Pin 10, wind 5 turns of item [4]. Finish at Pin 7. Use two layers of item [6] for basic insulation. Apply 3.0 mm wide margin to both sides of bobbin using item [5]. Match height of bias winding Start at Pins 4. Wind 14 turns of item [3]. Spread turns evenly across bobbin. Finish on Pins 5. Use two layers of item [6] for insulation Apply 3.0 mm wide margin to both sides of bobbin using item [5]. Match height of 1 layer of primary winding. Start at Pin 2. Wind 31 turns of item [3] and end at pin 1. Wrap windings with 2 layers of tape item [6]. Assemble cores item [1] on bobbin and secure using item [8]. Dip Varnish using item [9] Power Integrations Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com DER-114 PC Standby Power Supply – TNY280P June 28, 2006 8 Transformer Spreadsheets (Note – Output current is made 4.20 A in the spreadsheet to account for load on the auxiliary output) ACDC_TinySwitchIII_020706; Rev.1.6; ACDC_TinySwitch-III_020706_Rev1-6.xls; Copyright Power TinySwitch-III Continuous/Discontinuous Integrations 2006 INPUT INFO OUTPUT UNIT Flyback Transformer Design Spreadsheet ENTER APPLICATION VARIABLES VACMIN 85 Volts Minimum AC Input Voltage VACMAX 295 Volts Maximum AC Input Voltage fL 50 Hertz AC Mains Frequency VO 5.00 Volts Output Voltage (at continuous power) Power Supply Output Current (corresponding to peak power) IO 4.20 Amps Power 21 Watts Continuous Output Power Efficiency Estimate at output terminals. Enter 0.7 if no better data available n 0.75 Z Factor. Ratio of secondary side losses to the total losses in the power supply. Use 0.5 if Z 0.50 no better data available tC 3.00 mSeconds Bridge Rectifier Conduction Time Estimate CIN 100.00 100 uFarads Input Capacitance ENTER TinySwitch-III VARIABLES TinySwitch-III TNY280 Chosen Device User defined TinySwitch-III TNY280 TNY280 Standard Current Limit 0.698 0.750 0.802 124000 Amps Amps Amps Hertz 66.825 A^2kHz 100 Volts VDS VD KP 10 0.5 0.49 Volts Volts KP_TRANSIENT 0.27 ENTER BIAS WINDING VARIABLES VB 15 VDB NB VZOV 15.00 0.70 13.64 21.00 Volts Volts V_UV_TARGET 112.88 Volts V_UV_ACTUAL RUV_IDEAL 109.70 4.43 Volts Mohms RUV_ACTUAL 4.30 Mohms Chose Configuration ILIMITMIN ILIMITTYP ILIMITMAX fSmin STD I^2fmin VOR 100.00 Volts Enter "RED" for reduced current limit (sealed adapters), "STD" for standard current limit or "INC" for increased current limit (peak or higher power applications) Minimum Current Limit Typical Current Limit Maximum Current Limit Minimum Device Switching Frequency I^2f (product of current limit squared and frequency is trimmed for tighter tolerance) Reflected Output Voltage (VOR < 135 V Recommended) TinySwitch-III on-state Drain to Source Voltage Output Winding Diode Forward Voltage Drop Ripple to Peak Current Ratio (KP < 6) Transient Ripple to Peak Current Ratio. Ensure KP_TRANSIENT > 0.25 Bias Winding Voltage Bias Winding Diode Forward Voltage Drop Bias Winding Number of Turns Over Voltage Protection zener diode. UVLO VARIABLES ENTER TRANSFORMER CORE/CONSTRUCTION VARIABLES Core Type EEL22 EEL22 Core EEL22 EEL22_BOBB Bobbin IN Page 13 of 28 Target under-voltage threshold, above which the power supply with start Typical start-up voltage based on standard value of RUV_ACTUAL Calculated value for UV Lockout resistor Closest standard value of resistor to RUV_IDEAL P/N: User-Selected transformer core PC40EE22/29/6-Z P/N: EEL22_BOBBIN Power Integrations Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com DER-114 PC Standby Power Supply – TNY280P AE LE AL BW M L NS 3.20 3.00 5 DC INPUT VOLTAGE PARAMETERS VMIN VMAX June 28, 2006 0.358 6.32 1400 18 cm^2 cm nH/T^2 mm Core Effective Cross Sectional Area Core Effective Path Length Ungapped Core Effective Inductance Bobbin Physical Winding Width Safety Margin Width (Half the Primary to Secondary Creepage Distance) Number of Primary Layers Number of Secondary Turns 3.2 3 5 mm 103 417 Volts Volts Minimum DC Input Voltage Maximum DC Input Voltage Amps Amps Amps Amps Duty Ratio at full load, minimum primary inductance and minimum input voltage Average Primary Current Minimum Peak Primary Current Primary Ripple Current Primary RMS Current CURRENT WAVEFORM SHAPE PARAMETERS DMAX IAVG IP IR IRMS 0.52 0.30 0.6980 0.3448 0.44 TRANSFORMER PRIMARY DESIGN PARAMETERS LP LP_TOLERANCE NP ALG 1084 10 91 131 uHenries % BM 2671 Gauss BAC ur LG BWE 660 1967 0.31 34.8 Gauss OD 0.383 mm INS DIA 0.06 0.324 mm mm AWG CM 28 161 AWG Cmils CMA 364 Cmils/Amp 10.00 nH/T^2 mm mm TRANSFORMER SECONDARY DESIGN PARAMETERS Lumped parameters ISP 12.69 ISRMS 7.75 IRIPPLE 6.51 Amps Amps Amps CMS 1550 Cmils 18 AWG AWGS Typical Primary Inductance. +/- 10% to ensure a minimum primary inductance of 985 uH Primary inductance tolerance Primary Winding Number of Turns Gapped Core Effective Inductance Maximum Operating Flux Density, BM<3000 is recommended AC Flux Density for Core Loss Curves (0.5 X Peak to Peak) Relative Permeability of Ungapped Core Gap Length (Lg > 0.1 mm) Effective Bobbin Width Maximum Primary Wire Diameter including insulation Estimated Total Insulation Thickness (= 2 * film thickness) Bare conductor diameter Primary Wire Gauge (Rounded to next smaller standard AWG value) Bare conductor effective area in circular mils Primary Winding Current Capacity (200 < CMA < 500) Peak Secondary Current Secondary RMS Current Output Capacitor RMS Ripple Current Secondary Bare Conductor minimum circular mils Secondary Wire Gauge (Rounded up to next larger standard AWG value) VOLTAGE STRESS PARAMETERS VDRAIN 647 Volts PIVS 28 Volts TRANSFORMER SECONDARY DESIGN PARAMETERS (MULTIPLE OUTPUTS) 1st output VO1 5 Volts Page 14 of 28 Maximum Drain Voltage Estimate (Assumes 20% zener clamp tolerance and an additional 10% temperature tolerance) Output Rectifier Maximum Peak Inverse Voltage Main Output Voltage (if unused, defaults to Power Integrations Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com DER-114 IO1 PO1 VD1 NS1 ISRMS1 IRIPPLE1 PIVS1 Recommended Diodes PC Standby Power Supply – TNY280P 4.200 21.00 0.500 5.00 7.749 6.51 Amps Watts Volts Amps Amps 28 Volts MBR1060 CMS1 1550 Cmils AWGS1 DIAS1 18 1.03 AWG mm ODS1 2.32 mm Page 15 of 28 June 28, 2006 single output design) Output DC Current Output Power Output Diode Forward Voltage Drop Output Winding Number of Turns Output Winding RMS Current Output Capacitor RMS Ripple Current Output Rectifier Maximum Peak Inverse Voltage Recommended Diodes for this output Output Winding Bare Conductor minimum circular mils Wire Gauge (Rounded up to next larger standard AWG value) Minimum Bare Conductor Diameter Maximum Outside Diameter for Triple Insulated Wire Power Integrations Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com DER-114 PC Standby Power Supply – TNY280P June 28, 2006 9 Performance Data All measurements performed at room temperature, 60 Hz input frequency. 9.1 Efficiency (4 A Load on 5 V Output) Figure 6 – Efficiency vs. Input Voltage, Room Temperature, 60 Hz. 9.2 No-load Input Power Figure 7 – Zero Load Input Power vs. Input Line Voltage, Room Temperature, 60 Hz. Page 16 of 28 Power Integrations Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com DER-114 9.3 PC Standby Power Supply – TNY280P June 28, 2006 0.5 W (5 V, 0.1 A) Load Input Power Figure 8 – 0.5 W Load – Input Power with & without bias winding. 9.4 Available Standby Output Power The chart below shows the available output power vs. line voltage for an input power consumption of 1, 2 & 3 watts respectively. ON/OFF control is valuable in maintaining high efficiency under light load conditions, and helps meet many standby requirements. Figure 9 – Available Standby Output Power. Page 17 of 28 Power Integrations Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com DER-114 9.5 PC Standby Power Supply – TNY280P June 28, 2006 Regulation 9.5.1 Load Figure 10 – Load Regulation, Room Temperature. 9.5.2 Line Figure 11 – Line Regulation, Room Temperature, Full Load. Page 18 of 28 Power Integrations Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com DER-114 PC Standby Power Supply – TNY280P June 28, 2006 10 Thermal Performance Temperature measurement of key components were taken using T-type Thermocouples. The thermocouples were attached directly to the SOURCE pin of the TNY280P device and the case of the output rectifier. The thermocouples were glued to the output capacitor & to the external core and winding surfaces of the transformer T1. The cooling of the TNY280P is achieved through the copper plane on the PCB. It is necessary to provide adequately large copper area on the PCB attached to the SOURCE pins (5, 6, 7 and 8) of the DIP-8 package, to achieve the required cooling (se figure 3). These results indicate an acceptable temperature rise of key components when ambient is increased to 50 ºC. Temperature (°C) Item 85 VAC Page 19 of 28 115 VAC 230 VAC Ambient 25 25 25 Transformer (T1) core 49.9 45 44 Transformer (T1) coil 52.4 50.6 49.6 Tiny-Switch (U1) 62.3 56.3 49 Rectifier (D7) case 75 75 74 Power Integrations Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com DER-114 PC Standby Power Supply – TNY280P June 28, 2006 11 Waveforms 11.1 Drain Voltage and Current, Normal Operation Figure 12 – 90 VAC, Full Load. Upper: VDRAIN, 50 V / div Lower: IDRAIN, 0.4 A, 1 µs / div Figure 14 – 90 VAC, Full Load VDRAIN, 50 V, 10 µs / div. Page 20 of 28 Figure 13 – 283 VAC, Full Load Upper: VDRAIN, 100 V / div Lower: IDRAIN, 0.4 A, 0.5 µs / div Figure 15 – 283 VAC, Full Load VDRAIN, 100 V, 20 µs / div. Power Integrations Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com DER-114 PC Standby Power Supply – TNY280P June 28, 2006 11.2 Drain Voltage & Current Startup Profile Figure 16 – Start-up Profile, 90 VAC Upper: VDRAIN, 200 V / div Lower: IDRAIN, 0.4 A, 50 ms / div Figure 17 – Start-up Profile, 283 VAC Upper: VDRAIN, 200 V / div Lower: IDRAIN, 0.4 A, 50 ms / div 11.3 Output Voltage Startup Profile Figure 18 – Start-up Profile, 90 VAC (No Load) VOUT, 1 V, 5 ms / div. Page 21 of 28 Figure 19 – Start-up Profile, 90 VAC (Full Load) VOUT, 1 V, 5 ms / div. Power Integrations Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com DER-114 PC Standby Power Supply – TNY280P Figure 20 – Start-up Profile, 283 VAC (No Load) VOUT, 1 V, 5 ms / div June 28, 2006 Figure 21 – Start-up Profile, 283 VAC (Full Load) VOUT, 1 V, 5 ms / div. 11.4 OV Shutdown Two different OV Protection circuits can be designed with TinySwitch-III. Figure 22 shows operation of primary side OV protection circuit (JP1 and JP2 not installed) and feedback disconnected to cause OV condition at the output. Figure 23 shows OV protection offered by VR3, U4 & R10 circuit (Feedback disconnected during operation to cause OV condition at output). Figure 22 – 5 V Output Voltage. VOUT, 2 V, 200 ms / div Page 22 of 28 Figure 23 – 5 V Output Voltage. VOUT, 2 V, 20 ms / div. Power Integrations Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com DER-114 PC Standby Power Supply – TNY280P June 28, 2006 11.5 Load Transient Response (3 A to 4 A Load Step) In the figures shown below, signal averaging was used to enable better viewing of the load transient response. The oscilloscope was triggered using the load current step as a trigger source. Since the output switching and line frequency occur essentially at random with respect to the load transient, contributions to the output ripple from these sources will average out, leaving only the contribution from the load step response. The waveforms (Figures 24 and 25) show an instantaneous voltage change of 70 mV for a 75% - 100% step load change. Increasing the size of the output filter capacitor minimizes the 70 mV change. Figure 24 – Transient Response, 90 VAC Upper: VOUT, 100 mV, 2 ms / div Lower: IOUT, 3 A to 4 A Load Step Page 23 of 28 Figure 25 – Transient Response, 283 VAC Upper: VOUT, 100 mV, 2 ms / div Lower: IOUT, 3 A to 4 A Load Step Power Integrations Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com DER-114 PC Standby Power Supply – TNY280P June 28, 2006 11.6 Output Ripple Measurements 11.6.1 Ripple Measurement Technique For DC output ripple measurements, a modified oscilloscope test probe must be utilized in order to reduce spurious signals due to pickup. Details of the probe modification are provided in Figure 26 and Figure 27. The 5125BA probe adapter is affixed with two capacitors tied in parallel across the probe tip. The capacitors include one (1) 0.1 µF/50 V ceramic type and one (1) 1.0 µF/50 V aluminum electrolytic. The aluminum electrolytic type capacitor is polarized, so proper polarity across DC outputs must be maintained (see below). Probe Ground Probe Tip Figure 26 – Oscilloscope Probe Prepared for Ripple Measurement. (End Cap and Ground Lead Removed) Figure 27 – Oscilloscope Probe with Probe Master 5125BA BNC Adapter. (Modified with wires for probe ground for ripple measurement, and two parallel decoupling capacitors added) Page 24 of 28 Power Integrations Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com DER-114 PC Standby Power Supply – TNY280P June 28, 2006 11.6.2 Measurement Results Figure 28 – 5 V Ripple, 90 VAC, Full Load. VOUT, 20 mV, 10 ms / div Page 25 of 28 Figure 29 – 5 V Ripple, 283 VAC, Full Load. VOUT, 20 mV, 10 ms / div Power Integrations Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com DER-114 PC Standby Power Supply – TNY280P June 28, 2006 12 Design Notes: 1. Use of sufficient copper area directly under the TNY280P device, connected to the SOURCE pins of the IC is recommended for effective cooling. Generally, 1 square inch of symmetrical copper (2 oz) should be sufficient. However, actual temperature measurements should be used to determine adequacy. This is especially important when using the TinySwitch-III devices at or near the power levels specified on the datasheet output power table. 2. A dummy load (R2 in figure 2) was used in this design to ensure appropriate line & load regulation of the auxiliary output. Since this output is not directly regulated, it has a slightly higher output voltage when unloaded. The value of R13 should be selected, based on the current drawn by the external circuit that loads the auxiliary output. The filtering of the auxiliary output, and the need for an additional filter stage should be carefully evaluated, based on the load circuit’s requirements. 3. R13 & C4 form a RC filter to reduce the ripple voltage on the auxiliary output 4. In many applications, the snubber circuit (R3, C3 & R1) can be eliminated, depending on the EMC compliance requirements of the system. 5. The size and specification of the output diode (D7) heat sink depends on load and operating conditions. In some designs, where augmented airflow is available, a small surface-area heat sink may be sufficient. Page 26 of 28 Power Integrations Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com DER-114 PC Standby Power Supply – TNY280P June 28, 2006 13 Revision History Date Author 28-June-06 RJ Page 27 of 28 Revision 1.0 Description & changes Initial Release Reviewed PV / JJ / KM Power Integrations Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com DER-114 PC Standby Power Supply – TNY280P June 28, 2006 For the latest updates, visit our website: www.powerint.com Power Integrations may make changes to its products at any time. Power Integrations has no liability arising from your use of any information, device or circuit described herein nor does it convey any license under its patent rights or the rights of others. POWER INTEGRATIONS MAKES NO WARRANTIES HEREIN AND SPECIFICALLY DISCLAIMS ALL WARRANTIES INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY RIGHTS. PATENT INFORMATION The products and applications illustrated herein (including circuits external to the products and transformer construction) may be covered by one or more U.S. and foreign patents or potentially by pending U.S. and foreign patent applications assigned to Power Integrations. A complete list of Power Integrations’ patents may be found at www.powerint.com. The PI Logo, TOPSwitch, TinySwitch, LinkSwitch, DPA-Switch and EcoSmart are registered trademarks of Power Integrations. PI Expert and PI FACTS are trademarks of Power Integrations. © Copyright 2005 Power Integrations. Power Integrations Worldwide Sales Support Locations WORLD HEADQUARTERS 5245 Hellyer Avenue, San Jose, CA 95138, USA Main: +1-408-414-9200 Customer Service: Phone: +1-408-414-9665 Fax: +1-408-414-9765 e-mail: [email protected] GERMANY Rueckerstrasse 3 D-80336, Muenchen Germany Phone: +49-895-527-3910 Fax: +49-895-527-3920 e-mail: [email protected] JAPAN 1st Bldg Shin-Yokohama, 2-12-20 Kohoku-ku, Yokohama-shi, Kanagawa ken, Japan 222-0033 Phone: +81-45-471-1021 Fax: +81-45-471-3717 e-mail: [email protected] TAIWAN 5F-1, No. 316, Nei Hu Rd., Sec. 1 Nei Hu Dist. Taipei, Taiwan 114, R.O.C. Phone: +886-2-2659-4570 Fax: +886-2-2659-4550 e-mail: [email protected] CHINA (SHANGHAI) Rm 807-808A, Pacheer Commercial Centre, 555 Nanjing West Rd. Shanghai, P.R.C. 200041 Phone: +86-21-6215-5548 Fax: +86-21-6215-2468 e-mail: [email protected] INDIA (TECHNICAL SUPPORT) 261/A, Ground Floor 7th Main, 17th Cross, Sadashivanagar Bangalore, India 560080 Phone: +91-80-5113-8020 Fax: +91-80-5113-8023 e-mail: [email protected] KOREA RM 602, 6FL Korea City Air Terminal B/D, 159-6 Samsung-Dong, Kangnam-Gu, Seoul, 135-728, Korea Phone: +82-2-2016-6610 Fax: +82-2-2016-6630 e-mail: [email protected] UK (EUROPE & AFRICA HEADQUARTERS) 1st Floor, St. James’s House East Street, Fernham Surrey, GU9 7TJ United Kingdom Phone: +44 (0) 1252-730-140 Fax: +44 (0) 1252-727-689 e-mail: [email protected] CHINA (SHENZHEN) Room 2206-2207, Block A, Elec. Sci. Tech. Bldg 2070 Shennan Zhong Rd Shenzhen, Guangdong, China, 518031 Phone: +86-755-8379-3243 Fax: +86-755-8379-5828 e-mail: [email protected] ITALY Via Vittorio Veneto 12 20091 Bresso MI Italy Phone: +39-028-928-6000 Fax: +39-028-928-6009 e-mail: [email protected] SINGAPORE 51 Newton Road, #15-08/10 Goldhill Plaza, Singapore, 308900 Phone: +65-6358-2160 Fax: +65-6358-2015 e-mail: [email protected] APPLICATIONS HOTLINE World Wide +1-408-414-9660 Page 28 of 28 APPLICATIONS FAX World Wide +1-408-414-9760 Power Integrations Tel: +1 408 414 9200 Fax: +1 408 414 9201 www.powerint.com